Hi all,
Just spent a VERY frustrating day - read all i could find and learned much more than I wanted to know about PCs (I use a MAc).
Upgraded to wm5 using Build 14343. Now I cannot load anything into the phone using Activesync OR Missing Sync. Activesync won't recognise the phone at all, and I tried every suggestion on the boards - firewall ports, tcp/ip, reinstalling 4.5 then back to 4.2.
It's interesting that Missing Sync (Mac) will recognise and sync but won't allow me to install - .cabs just vanish into the ether.
Is WM5 actually worth it all? It seems like I've lost a lot of useful capability (buttons, camera, etc) for no great reason.
Any solves greatly appreciated. Now I'm going to bed.
Paul D
Baniaczek's WM5 ROM is great for me. It has tons of things way better than the original Wm2003. Connects to ActiveSync without a problem. Try to put that one on the device.
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM5_Home
Better File Same problem
I've upgraded the ROM.
Still no activesync. Ran the troubleshooter.
Said there's an issue with RNDIS not giving an IP address.
I've checked the LAN connection in Network settings but it won't repair.
I'm not even sure that Activesync created the link as there doesn't seem to be the "Connect using WM device" that it says should be there.
What now?
*&^%$* WinDoze. Roll on iPhone OSX.
Ahh. This is clearly an issue with the PC. If you were able to upgrade the rom - that prooves that your cable and your BA is okay. There must be some Antivirus, or Firewall problem. If you're using BitDefender Antivirus, for example, this is a known issue. You need to update it. Other antiviruses/firewalls may have similar issues.
Try to move to another PC, or reinstall your Windows PC. This problem is not related to your BA.
Another idea:
Unplug device, then
Start > Settings > Connections > USB to PC:
Disable the Advanced network functionality > ok
Plug it back
This will make your PDA connect to the PC via a Serial link (Like Wm2003 used to), rather than a network link (Like WM5 uses to).
It's still a PC problem though.
reflash again your pda.
today i had the same problem after one clean intall.
upgraded again with the same rom (the one you can see in my signature) and now, i am able to use active synch.
Ok Some Progress
I disabled the "advanced network functionality".
Active Sync no luck - it isn't correctly installing the hardware in Virtual PC on the Mac. I don't know why.
However, Missing Sync now actually begins to load activesync on the PPC, and then gives this message:
"Cannot start communications with the desktop computer. The communications port is not available. Another program may be using the port, or it may not be valid.
Quit any programs that may be using the port and reconnect. If the problem persists, restart your device using hte instructions provided by the manufacturer."
I remember reading somewhere that Baniaczek had assigned certain ports to certain things. How do I find out which it wants and change it?
thanks guys, we may lick this yet.
Paul D
Same message in VPC
Hooray,
I now get the same message in Virtual PC, after disabling "Virtual switch networking" and restarting the PC.
This means that the issue is now the port on the PPC.
PaulD
That's great..
I don't think so...
In baniaczek's rom, COM6 is assigned to shared GPS, but that can be easily changed from the settings, by setting it to none.
Go with your BA to a real PC that has only WinXP and ActiveSync installed, and nothing else (especially no Antiviruses). And no virtual PC's, as they depend on the host os! It's normal, because if your host OS can't connect, the virtual OS inside will have the same door closed.
I had the same problem before, and I definitely state that this is a PC problem, not a device problem. Same hardware connected to a different PC, will work, you'll see...
Reflashing the rom may help, as it will be detected as a new harware, that your system will let in. But you say you already did that...
Won't actually solve the problem
If I had a PC, that would be the easy solve. I don't, and really need the &$# thing to work on the machine I have.
For the moment I went back to the original Mamaich 14343. I can get .cabs into the phone via the card reader (the original problem on the Mac is that Missing Sync 3.0.2 has installing issues).
that doesn't allow me to load .exe, for which I need activesync, on my Mac, which runs VPC 7.0.2.
I really need to find out why VPC isn't working with TCP/IP.
Baniaczek's ROM is the best apparently, but has a com issue. It is also much easier to installl than any others I've found. I tried Xplode's ROM kitchen but the exe file wont run.
Paul D
hey, reinstall again the rom!
OK OK
Ok Sandstorm, I'll try it when I get the chance. At the moment the phone works but this ROMisn't as good as Baniaczek's.
Thankx for the tips
PauL D
Device won't install
Ok Internet works. TCP/IP works.
Issue now is that the device won't install properly - keeps giving a #10 error (device won't start).
So I can't reflash the ROM or anything until I get XP recognising the connection.
Paul D
turn on the upgrade program, "kill" the active synch running processes in your xp taskmanager, set the device in "bootloader" mode, place it in the crade and run the upgrade.
When i do my upgrades, i never do them with active synch enabled.
upgraded ROM again
Upgraded again - still no change
I flashed again to Baniaczek's ROM. Still will not install correctly in VPC. XP says I have a Generic Blue Angel connected via USB, but will NOT install the WM5 device.
Is this a COM port issue? Can I change that (details please)? For some reason, VPC simply won't recognise the WM5.
I have turned off "Advanced network connections" on the XDA. Nothing. Turned it back on.
I have it set to: server-assigned Ip address.
I have tried to change the IP settings manually, but never had a response. I might fiddle with that again.
AAAAAARRRGH!
thanks all,
Paul D
Related
After a hard reset on the TyTn my computer is no longer detecting it when I connect the phone to USB cable. The computer makes a sound when I connect it, but Windows Mobile Device Centrer say that TyTn II is not connected, and it does not show up in My Computer eather.
I've tryed to delete the partnership and reconnect the phone, but nothing happens.
Can anyone help me please! Now I cant install any of my programs og transfer files between the computer and the pocket pc/phone.
Try this:
tap Start > Settings > Connections.
tap USB to computer.
Uncheck the Enable advanced network functionality box
Try this:
tap Start > Settings > Connections.
tap USB to computer.
Uncheck the Enable advanced network functionality box
I uninstalled Windows Mobile Device Centrer and then tryed the tip you described here. At first it looked ok, my computer detected the device and installed the drivers and reinstalled Windows Mobile Device Centrer.
But my device is still not showing up in Windows Mobile Device Centrer or My Computer
Check your personal firewall settings and open the ports MS asks you to at the Windows Mobile home/support page...
Go into task manager & see if Activesync is running. I have the same problem with my tilt & if I kill activesync then reattach it takes a moment the first time, but then it works.
Make sure you are running the latest version of WMDC. I absolutely could not get WMDC to work with my HTC Wizard for months. After MS came out with an updated version of WMDC (around June, I think) it started working fine.
If you absolutely can't get it to work, consider using emoze for over the air syncing of cal, contacts, mail, etc. (or an on-line exchange account.) I had to do that for a few months until I got it to work. Emoze has the advantage of being free. Unfortunately, neither will allow file syncronization, tho.
There is no activesync running.
And everything was working just fine before my device went "mental" and I had to hard reset. So before the hard reset I could use WMDC on this computer, transfer files and run active sync. But now I cant.
I also got an online exchange account so I can sync calender and contacts. But I want to be albe to transfer files to my computer and install new software.
My WMDC version is: 6.1.6965
Some more info about the computer may help. For instance, I take it from your usage fo Windows Mobile Device Center that you are running Vista. In any case, since the problem is with the computer and not the Kaiser, I would see if the manufacturer would provide some support.
Yes, im running Vista and I buildt the PC my self.
But Im not sure its realy the PC that is the problem, because I made the changes (Hard Reset) to the device and thats what caused the problem.
Anyway, I was hoping for some way to debug/troubleshoot this problem.
I am having the same problem. I sync to any one of 8 computers at work and one at home. Work runs XP PRO and Home VISTA Ultimate x64 all worked fine untill this week. I have not made any changes since the last sync, the computers know it's hooked up due to activesync opening and trying to connect when I plug in via USB. But it never connects. I want to flash to Dutty's newest ROM but can't connect. I sync all contacts and e-mail wirelessly but need the computer to flash (I do not have a sd card yet) Any idead would be great! I have tried the ideas listed above but no joy. I have not hard reset the device as of yet ( I need some things off of it first)
Steve
BUMP
I really need help with this!!! I'm pulling my hair out!
Did any of you that had this problem find a solution? I have the exact same issue except a hard reset will fix it for a while, and then the problem will reoccur a few months later. No software has been added during the time frame. Very annoying.
i've got just the same problem! plaese help us!
i'm not able to install wmdc. it says it is for vista only. i'm currently on winxp. tried to install it via the disc provided..
lipanz said:
i'm not able to install wmdc. it says it is for vista only. i'm currently on winxp. tried to install it via the disc provided..
Click to expand...
Click to collapse
omg!
try activesync for XP. It came with the phone or you can download it from.
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-synch.mspx
Hi,
since a couple of days, my XDA II doesn't sync any more. It has still worked finefor a long time, since I have updated to WM6.
With my Orbit 1 async is always working fine.
When I connect it to the PC, the PC is always looking for a USB Driver.
Configuration:
Win XP; Async 4.5
XDAII WM6 by Shekhar 70C40CS
What I've tried: - changing USB-Connection and cable
- hard and Softreset
- changing USB to PC advanced network
- reinstalled async
- trying another PC
- reinstalling WM6 - no way, cause there is no USB driver
Maybe, that it is a hardware problem; but I doubt it, cause everytime, when I connect it to the PC, the PC ist trying to install a driver. So I think, there might be a software problem into the Himalaya.
Any ideas?
Sync problem - missing Driver.
Same problem with me on my notebook. Ask for help in another thread a few week ago, and got the advice to swith to active sync 4.5. I did so on my desctop and it worked wonderfull. On my notebook I stayed on as 3.8 because of my xda II and my old mda I. After I upgraded all my three xda to German WM6 i switched to as 4.5 german. I was verry suprised to get that fault window about the missing driver for that prototype thing and changing the vendor.
Not a mess I still have the desktop to install .exe and then copy the .cab files I need to my sd-cards. It´s not the known problem with the firewall (zone alarm), but it is a good question why as an the desctop works and the notebook doesn´t. Next I try to install the copied as-file from the desktop. Don´t know if it helps, I post if it does.
Hi, I had exactly the same problem, but I solved it in seconds because of Your last thread, thanx.
I had configured my windows firewall with "no exceptions".
I reactivated /checked the firewall-exceptions for ActiveSync on the PC and activated the extended networkfunctions under usb to pc on the xda and immediately everything worked fine.
Solved my problem too. Nice to help you.
Fine that I helped you, it wasn´t my purpose.
I got rid of that dammned thing about the missing driver for Prototype.
Read the hints of Jo_III in Post #28 and #31:
http://forum.xda-developers.com/showthread.php?t=341221
and follow exactly.
Insert in /windows with the name changed, rename it afterwards.
No question, why this is possible without the massage that it is impossible, as you get it, when you try to replace directly, but it works!!
Then soft reset and change /settings/connections Advanced Network Funtionality to disable/unchequed.
The funny thing with me is, that on my Dektop-PC both works.
Advanced Network Funktionality enabled the driver is for the Prototype.
This funktion disabled finds a WinCe Device.
Both works fine. No freesed PPC when disabled any more.
On my own notebook I can connect to the PC only in disabled Mode. When enabled this prototype driver problem is still there.
On the notebook of my beloved wife as4.0 recognizes the PPC an a WinCE Device but has a problem code 10. Think it´s normal as it is 4.0 and 4.5 installs new usbdriver while upgrading.
I tryed to upgrade to 4.5 and the windows installer crashed. I love it, really nice. I don´t want to fix this, I think, for me it is OK to ignore this.
This funny behavior, as i discribed it above, all my upgraded XDA/Qtek (all three of them) do.
PS. I use the German Rom of Teijalk with HTC Home and SCLPC++ Cube and I love it. Works perfekt and really fast and stable even with lots of proggis on RamDisk and few RAMStorage left, still really fast with my Pluscom WLan Card.
The Link is:
http://rapidshare.com/files/88608779/WM6ger.zip.html
More stuff like this. Thank You - thombs up!
The info above is wrong.
Only on my Qtek this solved my problem. Both of my XDA can´t deaktivate RDNIS for serial connection, when I try to uncheque Advanced Net Funktionality.
Don´t know why, I did the same on the other device without an error.
(Now I examined, that I used Port 8 twice. Once for serial to USB connection and second for external GPS connection, so it wasn´t able to deactivate this funktion anymore. I changed Port and everything is fine again.)
Final problem solved
totoche330 got the solution to my XDA sync problem in the thread above.
After Hard reset (No,Yes,Yes) inserting and renaming the dll. Soft reset and deactivating adv net funktionality. Works.
Don´t know why it didn´t work as it worked with my Qtek with all the programs installed, but dosn´t matter.
The problem of my notebook might have some reason:
The missing driver is called a Remote Network Driver Interface Specification to USB (RNDIS).
I think, I disabled everything to remote, because of one up to 25 trojan attacks.
I cured my xp, but i didn´t do a new setup. On the other hand it´s the only XP-Pro SP2. Desktop and other notebook are Home Edition SP2, but this is not important anymore. All PPC sync and that´s what it was about.
Two or three hours work and all the progs are back again. I hope, you can solve your problems too. Good Luck.
Does noone can write a driver for the cf-slot of the backpack?
Sometimes after soft reset you have to cheque and uncheque adv net funktionality inorder to get synced!!
Hi, i have recently installed ms active sync 4.5. However my tytn ii will not establish a connection with my pc. It charges just fine but does not connect. I have searched all over but did not find a solution to my problem. i was wondering if it mightbe the cable i got with my device when i purchased it. it is a usb to "mini usb" like the motorolas and nokia 6300 use. Could this be my problem?
I doubt it's because of the cable (though could be). Try unchecking start>settings>connections>usb to pc.
I have the same problem, and have tried connecting with and without advanced network functionality.
activesync does not respond at all, even when trying to connect from activesync on my pc.
I have the same problem, charging o.k., but USB connecting not work
Before I had same problem. The reason was I have installed some 3rd party program what somehow blocked the sync.
I have un-installed this program but it couldn't help because the registry setting was modified by this software. So finally I ended up with a hard reset and reinstall everything. After that the sync just work fine again.
Sigh, i thought it might come to that.
hard reset 2x, no effect
flah rom from SD card, Duty V1 Daimond....no effect
flah rom from SD card, L26 V6 Daimond.... I have the same problem, charging ok, USB data connecting not work...
Well, hard reset complete to no effect. So frustrating!!!! I have been troubleshooting for ages and have nothing to show for it. Surely someone on this forum has solved this problen before.
Hi
I had the same problem following a rebuild of my laptop.
Problem traced to my firewall which had blocked the connection.
Once rule changed to allow no further problems.
Hi colinm, what did you do exactly? It may help me out of this situation.
Doesn't anyone know anything about this?
Yeah i had it get the latest update for active sync from windows its a latest driver pack goto teh windows home and look on there it sorted my one out
what version is it? i have 4.5 right now.
If you could provide a direct link that would be great.
I was trying in 2 different PC ( Vista, Win XP), but the same problem, cable is ok....
I would really like to know what the more experienced members think about this but no-one really seems to want to reply. also i would like to know is the usb data cable plug identical to the htc original handsfree plug which is an exact fit. as i mentioned before my data cable is more like a mini usb, like the motorolas use. it fits (not perfectly like the handsfree), charges but there is no recognition between the device and the pc (xpSP2 running activesync 4.5 which came with the device).
Please help, i may seem to be a noob but i have tried available advice and troubleshooting has become repetitive.
My Mobile Device Center from my Tilt to Windows Vista stopped working a few weeks ago. Tried everything to no avail.
there was one thing that i couldn't do while troubleshooting.
"Do the following:
Disconnect the device.
Open Network Connections in Control Panel on the PC.
Note If your Control Panel is set to Category View, open Network and Internet Connections, and then open Network Connections
Right-click the local area connection created by ActiveSync, and click Properties. In the Connect using box, Windows Mobile-based device is displayed.
In This connection uses the following items, select every check box (to select all protocols).
Reconnect the device."
i cannot see the network icon active sync has created. which leads me to believe that this might be the problem. does anyone know how to fix this?
will updating to SP3 do anything, gonna try will let you know.
link with answer:
http://forum.xda-developers.com/showthread.php?t=362679
thanks champ worked a treat. eventually.
Hi,
I am getting a bit frustrated over this.
When I connect my X1 to my Vista x86 nothing happens (well the USB task tray icon show for about a second and vanishes again).
When I disable the "advanced option" in the USB/PC connection settings in the X1 I at least get a USB connection with something identified as "PocketPC USB Sync".
Any idea why this is happening and how I can get a real connection with the win mobile device center?
Thanks for helping me out!
Cheers,
Tillman
maybe give this a try:
http://modernnomads.info/wiki/index.php?page=Windows+Mobile+Device+Center+Troubleshooting
I've once had the issues of not able to connect my Windows Mobile device with vista too, and it can get very annoying.. good luck with it.
You might want to try and disable the firewall and then connect the device. I had this problem with Sygate Personal Firewall (sygate was bought by symantec and personal firewall is now terminated and no longer available)
Thanks for the quick response guys!
I already tried disabling the firewall (nod32) but that did not help.
Also checked all services - everything is peachy in that department.
But still - no connection.
When I switch back to "legacy mode" (disabling the advanced option in usb/pc settings on the device) then the device will tell me that I need to install active sync 4.5 or higher and wmdc still does not connect.
This is really strange...and annoying and the same time.
Any more ideas or any way for me to debug what's going on?
Thanks for you help!
Have you intalled "Windows Mobile Device Center 6.1" on your Vista-PC?
The MobileDeviceCenter should be standard without the need to install...
At my Vista Home the X1 had no problems to connect.
Open the Mobile Device Center and delete all old connections of other PPC. Then start your PC again, Softreset your X1 and try again. This should help. I had the problems too, when first connecting, because he didn't liked my G900-connection which was first
After this I too could install my G900 again and no problems since yet (2 weeks).
pf said:
The MobileDeviceCenter should be standard without the need to install...
At my Vista Home the X1 had no problems to connect.
Open the Mobile Device Center and delete all old connections of other PPC. Then start your PC again, Softreset your X1 and try again. This should help. I had the problems too, when first connecting, because he didn't liked my G900-connection which was first
After this I too could install my G900 again and no problems since yet (2 weeks).
Click to expand...
Click to collapse
Well sometimes the Mobile Device center could stuff up or not work due to some issues such as installation of Mobile Device Center 6.1 went wrong. I have experienced that I think I didn't follow the procedures correctly and things just wouldn't work. Eventually I had to do some uninstall and reinstall many times to finally get it working.
When I first plugged mine it it installed some drivers but didn't show up in the Mobile Device Center; unplugging and replugging in caused it to work...did you change settings in between plugging in for the second time?
What I have tried so far (and nothing worked):
Uninstall / reinstall WMDC
Uninstall / reinstall Win Mobile Remote Adapter (yes, this does show up once I am connected with "advanced" USB mode)
Uninstall / reinstall "PocketPC USB Sync" (shows when X1 is set to legacy USB mode)
When in "advanced" mode I can also see a new LAN connection showing up in network overview.
The same X1 on a different Vista 32bit right next to this one will connect just fine. So it's definitely about a driver or config thing with this Vista.
This is driving me...well you know what.
btw, you did try restarting your comp when performing some of those steps, and you did try different USB ports right?
I know that you had to ask.
Yes I did. I have rebooted the system several times in between all those reinstallation tasks.
By the way. When I am in USB legacy mode and reconnect the USB cable then the X1 will show a messagebox telling me that it's connecting with the host and that the user credentials / user account (having to translate here) are correct.
But still NO connection visible in WMDC.
I had the same problem with my X1. I assumed that because my HTC Diamond worked the X1 would as well.
I finally installed WMDC from the SE install cd, and bingo!! al good. Hope it works for you...
Wow!
Even though it does not work (yet) it's showing some new signs.
Installing WMDC from SE disc fails at 99% progress and then rolls back.
There's gotta be some installation error log this, right?
Thanks for coming up with that suggestion. Really, I should try installing from vendor CDs more often instead of hunting down the latest version on the net.
TillmanZ said:
Wow!
Even though it does not work (yet) it's showing some new signs.
Installing WMDC from SE disc fails at 99% progress and then rolls back.
There's gotta be some installation error log this, right?
Thanks for coming up with that suggestion. Really, I should try installing from vendor CDs more often instead of hunting down the latest version on the net.
Click to expand...
Click to collapse
maybe give event viewer a try and check under Windows Logs (not sure if it will be application or system tho)
just in case you aren't sure, in vista either type in "Event Viewer" in the start menu search bar, or type in "eventvwr"
Don't you just like vista?
That helped (to install SE's WMDC). The issue was that my HTC Universal was still connected to one USB port (for testing purposes since that device is not recognized either).
As soon as I unplugged the HTC I was able to complete the WMDC installation.
Unfortunately though it still won't connect to my X1.
Any more ideas?
what is your settings in Windows Mobile Device Center connection Settings?
Well here is my settings that is working with my x1:
Allow USB connections checked
Allow connections to "DMA"
This computer is connected to "Automatic" (this shouldn't matter)
Allow automatic device authentication checked
Allow data connection on device when connected to PC (this shouldn't matter either)
also, while this link was in the first link that I have posted for trouble shooting, just want to make sure you actually tried The offical Windows Mobile Device Center troubleshooting guide?
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center-troubleshooting.mspx
namely these steps:
Quote"
If Windows Live OneCare is installed on your machine, it may be blocking the device connectivity. Please click here for the steps to configure Windows Live OneCare to allow the device to connect.
My device wasn’t connected during this installation.
While it is not a strict requirement that you have a device connected during the installation process of Windows Mobile Device Center, we highly recommend that you do.
"
I didn't have the DMA set (changed that now). Everything else already was like you described and it does not work.
This really freaks me out. I always hated my iTunes/iPhone connectivity but that honestly works much smoother. Of course I do understand that this behavior is non standard as I have experienced myself that the phone works with my other Vista machine but that does not really help me here.
Any update on this? I am having the same problem.
I'm having the _exact_ same problem too, but in Vista x64. I don't know why WMDC can be such a c**t sometimes, as I have never been able to 'sync' with my Media Center PC.
My only saving grace is that my laptop has Bluetooth, and syncing works great on it. I have never had success connecting the USB cable (with many options changed around of course) to either of these computers. Only Bluetooth syncing works for me...
Hopefully we can find the answer!
What USB cable are you using??? the one that came with Xperia??? Cos the one that came with my Xperia never worked out of the box, it could only charge...
I also got another extra cord which came in another box, that worked fine for both syncing and transferring data until today, now it says USB device not recognized, maybe I was trying the flash X1 with new ROM through SEUS, did the whole lower volume key and power button to get the 3 strips.
Now I am using the USB cable that came with my external HDD, that's currently working, hopefully it won't fail me.
so any ideas??? I don't want to keep changing cables...
Peoples,
After flashiong a new ROM I have lost internet connectivity on my device when connected with Activesync to PC.
Re-flashed a different ROM (HTC stock standard) then another and the problems persists...this is with no additional s/w loaded on the device.
This makes me think it is an issue with my PC and possibly activesync. I re-installed activsync, no fix!
The device connects (no problems) and synchronises and I can open the deivce on the PC and see all...
Can anyone guide me through checking my PC/internet connections so as to troubleshoot as this is driving me nuts!?!?!
BTW, thought it might be firewalled out by windows XP but all seems in order there...
Looking forward to any help soonest......
Just to add that all works OK using my home Wifi connection....just when connected to Activsync with the USB cable......
Solution found....yay!
Unbelievable but true....simple solution that I waster 8 hours trying to fix by installing new ROMs, re0-installing Activesync, USB driver....you name it!
The solution was to Open ActiveSync, go to File, Connection settings.
There you will see "This computer is connected to" - Automatic
Change the dropdown arrow to.....The Internet and now it works
This Activsync software is pure rubbish...always has been and always will be....
At least I'm back in business and I hope others learn from my grief!!!