Hello,
I've searched a lot how to put the Herald in the boot loader mode.
Please, help me.
Thank you advance.
LAter edit: i found out: i had to keep pressed the camera button lol
If you searched a lil bit more you'll find that piece of info in herehttp://wiki.xda-developers.com/index.php?pagename=Herald_Resets
in the Wiki herald section
sandibad said:
Hello,
I've searched a lot how to put the Herald in the boot loader mode.
Please, help me.
Thank you advance.
LAter edit: i found out: i had to keep pressed the camera button lol
Click to expand...
Click to collapse
and in nearly everypost about unbricking and flashing.
Pleas read, read, read.
and btw: commmanager + camera + softreset.
Looking for
In fact, i read houdreds of time all the posts... at 5 AM...
Because by Herald was in the "white screen" and i was desperate...loking for solution ...
In fact, I have to wait for the official WM6 because that one didn't worked for me.
Thks for assistance.
papamopps said:
and in nearly everypost about unbricking and flashing.
Pleas read, read, read.
and btw: commmanager + camera + softreset.
Click to expand...
Click to collapse
No need to press comm.button. Just press camera and softreset at once, release the softreset first than camera button. That's all!
nugift said:
No need to press comm.button. Just press camera and softreset at once, release the softreset first than camera button. That's all!
Click to expand...
Click to collapse
OK. Thanks
BTW - my device is unbricked. BUT it was made by repairservice - for warenty. lol.
I´m happy again. Hehe
papamopps said:
OK. Thanks
BTW - my device is unbricked. BUT it was made by repairservice - for warenty. lol.
I´m happy again. Hehe
Click to expand...
Click to collapse
Damn you did not have to pay?? sweet!
Newbie here.....
I have an HTC P4350. During the upgrade, there was a disconnect with my computer to the phone, now I have that colored screen when I start up. I tried the hard and soft reset and also the Boot loader method.
Anyone have any other suggestions?
Do you think if the phone went back to HTC, they would be able to fix it?
Thanks for your help
You should be able to flash the original RUU when you're in bootloader mode ('the three colored screen') and connected to the PC with your USB cable. Worked for me anyways.
Just put your phone in bootloader mode, connect it to your computer and run the RUU.
R_phAn said:
You should be able to flash the original RUU when you're in bootloader mode ('the three colored screen') and connected to the PC with your USB cable. Worked for me anyways.
Just put your phone in bootloader mode, connect it to your computer and run the RUU.
Click to expand...
Click to collapse
The problem is that it won't connect to the computer via activeSync, until that happens the phone cannot be updated.
passmoregas23 said:
The problem is that it won't connect to the computer via activeSync, until that happens the phone cannot be updated.
Click to expand...
Click to collapse
Have you tried it before you said that it would not work? Seriously? When in bootloader mode, the computer doesn't connect via activesync (how could it, there is no operating system on the phone). Get into bootloader mode, connect the phone to the computer (yes, i know activesync doesn't show a connection at this point) and run the stock RUU for your device. If this does not work, then there is something seriously wrong with your device.
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
dcmtnbkr said:
Have you tried it before you said that it would not work? Seriously? When in bootloader mode, the computer doesn't connect via activesync (how could it, there is no operating system on the phone). Get into bootloader mode, connect the phone to the computer (yes, i know activesync doesn't show a connection at this point) and run the stock RUU for your device. If this does not work, then there is something seriously wrong with your device.
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
Click to expand...
Click to collapse
To add to this, when in bootloader and plugged into your PC, it will say "USB" at the bottom. That's how you know it's connected properly.
If you're having troubles and you're running Vista...
http://www.modaco.com/RUU-Vista-done-u-t252977.html
dcmtnbkr said:
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
Click to expand...
Click to collapse
Dude, I have searched for a resolve to my problem, and I do appreciate peoples help. I don't waste time of good Samaritans. I did run the RRU and I received an 260 error, which is another topic which I did research on as well.
I'm going to send the phone back to HTC and let them fix it.
Related
Today, I upgrade my HK XDA2s from eng to chinese, the chinese rom which was download from ftp , named "XDA_IIs_Chinese_CHT_1.31.00_ ExtRom_1.31.900_Radio_1.08.00.rar" (Thanks the giver)
During the installation, I have successfully to edit the 3 rom header file to avoid the country ID problem.
All thing go well, and the PC screen saying "Congradulation" at last.
However, after I soft reset my XDA 2s, the device hang on the start up screen, can't reboot further more.
Can anyone tell me how to solve it OR any steps I miss ?
Thanks
Did you do a Hard reset (power and reset) after the install like it told you to do on the screen?
MDAIIIUser said:
Did you do a Hard reset (power and reset) after the install like it told you to do on the screen?
Click to expand...
Click to collapse
Thanks MDAIIIuser reply.
After seeing the PC screen said "Congradulation"
I've try 1) Softreset and 2) hardreset too
But the problem stilll exist.
Thanks
Sorry, can't help out! never been down that path, alas wiki has no info on that issue.
MDAIIIUser said:
Sorry, can't help out! never been down that path, alas wiki has no info on that issue.
Click to expand...
Click to collapse
Thanks MDAIIIuser, you already help me a lot.
Hope other member who 've encounter the same problem can sharing with us.
Furthermore, MDAIIIuser, while using the rom mention above
"XDA_IIs_Chinese_CHT_1.31.00_ ExtRom_1.31.900_Radio_1.08.00.rar"
which is download from ftp server.
After upgrade, the start up screen is "Qtek" with KPN wording. It is very strange that why the chinese rom got "Qtek" wording.
It is there have something wrong on that files ?
You did what we all would have done, sorry that it was a waste of time.
This is another case of
FUNNY HA HA ... NOT
Check the thread on the t-mobile new rom found (cant post link am on mda). Here you will see that i found a new rom on ftp, posted it to wiki, downloded it and then cooked it to find out that it was a qtec rom.
What a waste of time that was.
We have one very sad person that thinks its funny to delete Ftp files, Ftp dirs and now post files that he/she knows would intrest some of us based on the threads that have been posted.
I for one will take more care when posting to wiki, pity as it takes the fun away.
after i finished update, i discover this topic....
I also hit this problem right now.
Can anyone tell me what can i do?
Dont think amy of our CHT are good, might try to download then and see if they work.
The link is in wiki, see my signature, you need the page with ship.exe in it.
idox said:
after i finished update, i discover this topic....
I also hit this problem right now.
Can anyone tell me what can i do?
Click to expand...
Click to collapse
Tell me which CHT ROM you did and how you flush Rom , maybe I can help,I try all CHT Rom in here except Dopod114 ROM was broken others all can flush,pm to me or replay in here I will help same as MDAIIIUser help me.
My new XDA IIs got a same problem here. It's dead. Anybody got a solution?
Do not worry. I have got the same problem before. I suggest you just flash back to your own rom.
bbrcn said:
My new XDA IIs got a same problem here. It's dead. Anybody got a solution?
Click to expand...
Click to collapse
re-flushing rom again , it's happen to me before,if you see usb 2.07 that need to re-flush again
Thanks for you two reply.
Yes I had thought about to it that way. But my problem is more serious the XDA stop at start screan the computer even can't detected it. I can't even do synch how can I flush it back? Is there any other way like "PC safe mode"? Anybody got a idea?
OK, move battery out wait 15 min , and put it back ,also reboot your pc,if don't work , try to remove and re-install ActiveSync .
try to doing soft reset first.
Thanx MWang.
Yes I tried what you said, still not working. The xda freezed at the first second it start. I think that is why pc can't detected it. Also soft reset will only turn off the xda and it won't start unless you use hard reset.
bbrcn said:
Thanx MWang.
Yes I tried what you said, still not working. The xda freezed at the first second it start. I think that is why pc can't detected it. Also soft reset will only turn off the xda and it won't start unless you use hard reset.
Click to expand...
Click to collapse
ok YOU DIDN'T SET ON Boot Loader Mode,TRY by pressing the camera button, power button and then the reset button and hold for a few seconds THAN YOU WILL SEE USB V-2.07 THAN PUT IN THE cradle THAN FLUSH YOU NEW ROM, I THINK SHOULD WORKING.
It do works by press voice record, power, reset together! :? Anyway it works again, just great!!
I'm really appriciated for your help mwang thank you!
ionutzu said:
Hi there,
I installed a bunch of stuff on the AKU3.2 Rom H-tec innov / O2 ROM which i found on the ftp and now when i soft-reset the phone, it either gets stuck (in windows) on Today, where it only loads like half of it and is consequently stuck or it resets again...
How would I be able to solve this issue having that it doesn't connect to ActiveSync?
Thanks a bunch,
John
Click to expand...
Click to collapse
ionutzu said:
OK let me clarify.... phone is totally unresponsive. I turn it on, HTC Innovation screen pops then the O2 with all the version, it loads windows and you can't really do anything but turn it off... or hard reset which doesn't help because the next time it loads, it just does the same thing...
What can I do
Click to expand...
Click to collapse
Thought it might've been in the wrong section!
Try to put it in bootloader mode and reflash. Goodluck!
clemsyn said:
Try to put it in bootloader mode and reflash. Goodluck!
Click to expand...
Click to collapse
Thanks for your reply, could you direct me please to somewhere where i can read of how to put it in bootloader mode? I have no idea and I can't find it in the manual. Thanks
If you want, you can IM me on YIM: ionutz_ceo
Thanks a lot
I've achieved putting it into bootloader mode, how would I go about reflashing now?
lol, ok!
So basically this is the result of my 2 hour research::
If you're Wizard is frozen, you do this:
1. Turn off USB in ActiveSync
2. Download mtty
3. While phone is off, press Camera button then holding it press Power button on phone and it will load in bootloader mode
4. Connect mtty to the phone via usb
5. <<< Here is when my research parts ways
6a. You can use a sd card and put an image on it, using mtty reflash the phone (don't know how to do that or where to get the image)
6b. There's another way of reflashing the phone...
Can anyone fill me in on that?
ionutzu said:
lol, ok!
So basically this is the result of my 2 hour research::
If you're Wizard is frozen, you do this:
1. Turn off USB in ActiveSync
2. Download mtty
3. While phone is off, press Camera button then holding it press Power button on phone and it will load in bootloader mode
4. Connect mtty to the phone via usb
5. <<< Here is when my research parts ways
6a. You can use a sd card and put an image on it, using mtty reflash the phone (don't know how to do that or where to get the image)
6b. There's another way of reflashing the phone...
Can anyone fill me in on that?
Click to expand...
Click to collapse
That seems a bit more complicated than what is really needed.
Assuming that your device was a G3 before you started, you are CID unlocked and you didn't overwrite incompatible bootloaders on a G4 device by using a G3 only ROM:
Once you are in bootloader, connect your USB cable. You should see the letters USB in the lower corner of your device.
Reflash with an official AKU2 ROM (latest available from your carrier's website.)
to do this once you are in bootloader mode and see USB in the lower corner execute the rom installer.
Don't flash an AKU3 Rom until you read all the threads completely on them. Several programs that work with AKU2 do not work with AKU3 and will freeze your device - Which appears to be what you are experiencing. There is still work being done on AKU3 and they aren't for mainstream use yet. There are driver incompatibilities, database restructures and such that haven't been accounted for in some software. The most common issues are documented repeatedly in every AKU3 ROM thread.
Zzan said:
That seems a bit more complicated than what is really needed.
Assuming that your device was a G3 before you started, you are CID unlocked and you didn't overwrite incompatible bootloaders on a G4 device by using a G3 only ROM:
Once you are in bootloader, connect your USB cable. You should see the letters USB in the lower corner of your device.
Reflash with an official AKU2 ROM (latest available from your carrier's website.)
to do this once you are in bootloader mode and see USB in the lower corner execute the rom installer.
Don't flash an AKU3 Rom until you read all the threads completely on them. Several programs that work with AKU2 do not work with AKU3 and will freeze your device - Which appears to be what you are experiencing. There is still work being done on AKU3 and they aren't for mainstream use yet. There are driver incompatibilities, database restructures and such that haven't been accounted for in some software. The most common issues are documented repeatedly in every AKU3 ROM thread.
Click to expand...
Click to collapse
Yes I agree with this the other option is a bit more complicated. This is much easier
@ ionutzu
Please update how the solutions above worked for ya. Zzan's solution is standard and most used along with being the easiest & should definitely work.
^^ you guys are wonderful!
Pretty much this is how it works, I couldn't find the "easy" solution anywhere, but now I figured it out.
1. Turn on phone holding camera button + power button
2. Connect via USB
3. Make sure USB is written in bottom left corner of PPC screen
4. Run an original ROM update (that is, the ones coming straight from T-Mob, I've tried it with other roms, it doesn't work)
5. It should work, you should have a fresh copy
6. I guess put your customized rom and try again....
Thanks for the help.
ionutzu said:
^^ you guys are wonderful!
Pretty much this is how it works, I couldn't find the "easy" solution anywhere, but now I figured it out.
1. Turn on phone holding camera button + power button
2. Connect via USB
3. Make sure USB is written in bottom left corner of PPC screen
4. Run an original ROM update (that is, the ones coming straight from T-Mob, I've tried it with other roms, it doesn't work)
5. It should work, you should have a fresh copy
6. I guess put your customized rom and try again....
Thanks for the help.
Click to expand...
Click to collapse
Glad it worked out for you.
after i used button's 1.05 ROM i cant get no usb and its very slow not i cant install HTC Wizard Unlocker UPDATE Version 0.2b
Do you mean no activesync by no USB? Try flashing it again through bootloader screen or try flashing the official rom of your provider through the bootloader.
how to get to the bootloader screen
cesarrri12 said:
how to get to the bootloader screen
Click to expand...
Click to collapse
when you soft reset hold the camera button
so just press the power then hold the cam key
Just use teh soft reset on the side then hold the cam-key
ivanwinkel said:
Just use teh soft reset on the side then hold the cam-key
Click to expand...
Click to collapse
Once at the bootloader screen, what do you do next? I've been stuck here for a little while now and can't figure out what to do while in this mode.
itburnout said:
Once at the bootloader screen, what do you do next? I've been stuck here for a little while now and can't figure out what to do while in this mode.
Click to expand...
Click to collapse
Read all the stickies (also in WM6 forum)! It's all explained there.
http://forum.xda-developers.com/showthread.php?t=298613
vippie said:
Read all the stickies (also in WM6 forum)! It's all explained there.
http://forum.xda-developers.com/showthread.php?t=298613
Click to expand...
Click to collapse
Yes, I've been over that, and some of the related links from that thread, but so far I still can't find the missing piece. All of the tips point to using an updater to load Wizard Love, but I still get a communication error. I can't figure out what I'm doing wrong.
I'd also point out that while this may be my third 4th post, I'm not really new at this. I am new at having problems. I've flashed this phone probably a dozen times in the past year and have never had a problem. I've going over the sticky threads and tutorials, but what I'm missing is how I actually get wizard love to load. So far, it still does a check for the phone through activesync, then tries to run RUUGetinfo.exe and EnterBootloader.exe to which copies nk.nbf. So far the central issue seems to be establishing a connection. Since I am already in the boot loader (the red, green, blue, white screen) I need to be able to copy nk.nbf, which is what I cannot figure out. So far, I haven't found anything useful on this.
I'd also point out that while this may be my third 4th post, I'm not really new at this. I am new at having problems. I've flashed this phone probably a dozen times in the past year and have never had a problem. I've going over the sticky threads and tutorials, but what I'm missing is how I actually get wizard love to load. So far, it still does a check for the phone through activesync, then tries to run RUUGetinfo.exe and EnterBootloader.exe to which copies nk.nbf. So far the central issue seems to be establishing a connection. Since I am already in the boot loader (the red, green, blue, white screen) I need to be able to copy nk.nbf, which is what I cannot figure out. So far, I haven't found anything useful on this.
When you just plugin USB cable. Does it say USB on the left bottom of your screen? After this you should just use the RUU. Maybe it helps to uncheck allow USB connections in activesync.
Most people having problems flashing from bootloader (communication error) can succesfully flash from another XP machine. Have you tried that?
Greetings everyone,
I would like to ask for some advice.
I bought a HTC TYTN II and wanted to flash it to a ROM I found on the forum.
But to do that I had to use nueSPL-2.47.exe
That turned out to be a mistake as at the moment it started formatting to FAT32 the screen freezed. And I waited for around 15min. But nothing happend.
Now needless to say the device does not function. I tried a hard reset(Camera+Power+Reset) and just (Reset). But all I get is a screen darker than the pits off hell.
I am able to get the power light burning but that is it. Already tried putting the battery out and in again. But all to no avail. Maybe one of you can help me?
Thank you in advance.
-
Previous OS: Windows 6.1 (Dutch)
Active sync: 4.5.0
PC OS: Windows XP pro (English)
Just a thought but...you might want to check the Kaiser forum instead...
Posted in Titan forum. Moved to Kaiser forum.
You flashed a Titan SPL to your Kaiser?
Oh dear, not to worry, it might be fixable...
Can you get to your Bootloader?
Ta
Dave
Confused "Tytn" with "Titan", too bad.. That's already happened, if you search for "nuespl" in the Kaiser forum you should find a thread about someone else who had the same problem recently.
kilrah said:
Confused "Tytn" with "Titan", too bad.. That's already happened, if you search for "nuespl" in the Kaiser forum you should find a thread about someone else who had the same problem recently.
Click to expand...
Click to collapse
The other guy never fixed his phone
Dave
uh oh... what was your radio version? does the PC still try to load a driver when you connect the phone?
Wrong firmware now that explains things.
It seems that the soft/hard reset and boot loader are not working for me. All I ever get is the power light and no screen at all.
Just my luck.
My phone was a 3G version.
When I connect it via USB it does try and load drivers but it does not find the correct drivers. While the phone was ok the drivers were fine.
Strange.
I sure hope I do not have to send it to my supplier. Because the phone is just 2 weeks old ;-)
Jin_member_of_triforce said:
Wrong firmware now that explains things.
It seems that the soft/hard reset and boot loader are not working for me. All I ever get is the power light and no screen at all.
Just my luck.
My phone was a 3G version.
When I connect it via USB it does try and load drivers but it does not find the correct drivers. While the phone was ok the drivers were fine.
Strange.
Click to expand...
Click to collapse
are you able to load these drivers: http://forum.xda-developers.com/attachment.php?attachmentid=71038&d=1203255530
3G, okay, all of them are 3G... do you remember exact radio version. no problem if not, though.
Sorry I do not know the exact number.
I was able to install the drivers. So thanks for that.
But If I try and get onto my phone I have no folders. And active sync does not see the device. Maybe I need to use a program like artemis to get files on there?
There is of course a change I might be able to get files on there by putting my SD card in a card reader.
But does it boot from there?
Pocket controller-pro did not work for me.
Jin_member_of_triforce said:
Sorry I do not know the exact number.
I was able to install the drivers. So thanks for that.
But If I try and get onto my phone I have no folders. And active sync does not see the device. Maybe I need to use a program like artemis to get files on there?
Click to expand...
Click to collapse
that will not help, but there is another way... PM me, as it needs interactive step by step instructions.
im having the same issue i just ran the neuspl 2.47 and my htc tilt wont work the power light comes on and thats it can somepone please help me out i am in need of help badly!
Hello,
I have put a cdma rom on my gsm Tp2.
It doesn't boot anymore
I cannot make connection with my computer.
What can I do?
with phone off hold down the volume key while pressing power key & your phone should boot into bootloader mode (tri-color screen) at the bottom it should read serial now plug phone into computer via usb cable and flash a rom tell me if it worked!
lol I did that the very first time I flashed a phone...dont feel bad.
i did it too!
hatsiflatsi said:
Hello,
I have put a cdma rom on my gsm Tp2.
It doesn't boot anymore
I cannot make connection with my computer.
What can I do?
Click to expand...
Click to collapse
lol good luck. hope u dont really sound like borat
It's not bricked, you can just do what waffles said above, and you will be able to flash the correct ROM.
However, please be very careful not to flash the wrong type of radio to your phone, otherwise it *will* be permanently bricked.
Dear waffles510,
It worked. Thanks, many thanks. I walked around with my spare Nokia today wich was a nightmare. I missed al the tools on the TP2.
Now I wonder why I need to connect with the WMDC normally.
Thanks!
hatsiflatsi said:
Dear waffles510,
It worked. Thanks, many thanks. I walked around with my spare Nokia today wich was a nightmare. I missed al the tools on the TP2.
Now I wonder why I need to connect with the WMDC normally.
Thanks!
Click to expand...
Click to collapse
Simple answer, you don't need to It's just easier for new people.
hatsiflatsi said:
Dear waffles510,
It worked. Thanks, many thanks. I walked around with my spare Nokia today wich was a nightmare. I missed al the tools on the TP2.
Now I wonder why I need to connect with the WMDC normally.
Thanks!
Click to expand...
Click to collapse
No problem! im always happy to help.