Hi,
i upgraded my charmer with the new uk t-mobile rom and my nproblem is that the battery does not charge,and i don't know how to do
have you some suggestions???
Waiting your answer,thanks a lot,Antonio
Hi did you get a answer
Hi I have the ssame problem, did anybody come up with any ideas ?
Cheers
TBW
Battery Problem
Hi, I have too this problem with wm6 rom have you some suggestions??? pleas
Hi...nobody can help us???
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
vlodeck said:
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
Click to expand...
Click to collapse
i have the same problem and doesn«t work for me
Then my guess is you flashed a ROM not intended for your device.
now how i can solve this?
Reflash a charmer rom? And if that doesn't work, try a prophet WM5 rom.
it says that i don't have enough battery, is lower than 50%
Use the NO_ID RUU version instead.
i already try a few roms and i can't flash the pda with none of them
You will need to reboot in BootLoader mode first (powerkey+camera+reset).
hello!
a downgrade my Charmer and now the battrery is 0%, when i connect to usb phone don't want to start, on charger it startet but battery dont want to charge. help pls ...
Hi,
I have solve this problem but I'm not sure how I've done this.
1. dowlnoad cab from this link http://forum.xda-developers.com/showthread.php?t=327988
2. I have use program Wizard Service Tool and clear everything what is possible including format.
3. reset
4. format after strart camera+record+soft reset
5. after reset bootloader mode, and first time my phone has connet in BLmode with USB.
6. Then I have run original T-mobile RUU and it's working
My battery has been on 0% in system as well but after downgrade battery states about 70%
have a same problem.
did anybody else solve this problem? anybody used SD flashing method?
i've solved problem partly - now battery charges, but i can't start it without power supply. so what have i done:
1) i've downloaded ShellTool_bugfixed.zip (you can easily find it google).
2) unpack it.
3) copy Cert_SPCS.cab and EnableRapi.cab to you WM and install
4) extract nk.nbf from original Charmer ROM into ShellTool folder
5) start ShellTool.
6) press Get ROM Info
7) press Extract OS
10) press Flash OS
11) press ОК
Followed all this steps, now i've got an original charmer os, but bootloader is still from previous crap ROM. so there is trouble with starting it up. If you phone doesn't start even when you charging it from power socket, so try to wet contacts on battery - it should work.
now i thinking how to re-flash bootloader, cuz it cannot enter into bootloader witout power supply from socket. It's no possible to flash it from PC, cuz it cannot enter a booloader plugged into USB port. It seem that there is not enough power impulse to startup.
Related
Hi guys,
I have a big problem with my charmer.
At the begining I tried to work with my charmer and it was OK, but after a short time it resets from alone. It was the same situation everytime, when the charmer was starting and I did the calibration of the touch screen it was reseting always as soon as I pressed the cross on the right bottom.
Next step was to flash the ROM - it was sucessful, but the same situation
-> Reseting at the calibration.
I did once again a flash but it resetet during flashing and now I have the situation, that I can enter boot loader but as soon as I connect it resets.
Battery I checked -> It is OK.
So does anybody have a Rom on SD card ? -> I have no other joice, this is my last chance to get it running again.
Thanks for your help in advance
Best regards
Helldriver
Hi
1. Kill (task manager) wescomm.exe (this is related with activesync installed on your PC).
2. Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
3. Now connect your USB cable to your phone
4. Download T-Mobile compactii_aku2.0_05-2006 rom and Flash it works for me
jerry
Not working with USB
Thanks for your comment, but it is not working, due to the fact that the MDA tripps as soon as I connect the USB cable (even if I kill the wecomm.exe).
Therefore my only chace is the SD-card
So if anybody has a ROM on SD card, please help me getting my Charmer running again.
Regards
Helldriver
Hi Gents
is there somebody who can help me ?
I really need a SD-card rom
Thanks
Helldriver
Sorry ,but I am noob. How can i flash it??? And how can i kill wescomm.exe???
Rom backup
Hi all,
Still searching for the SD ROm image... Can someone upload?
Please...
When i turn on my phone I get the Tri Colored screeen
and it says: Upgrade ROM error code please try again.
and then the phone turns off and on.... Please help....
please please HELP SOMEONE!!!!
Don't dispair! I had the same problem and got out of the situation: http://forum.xda-developers.com/showthread.php?t=505377&p=3677341
You probably have the wrong Original Rom from HTC installed (may wrong language).
To solve the situation you will need USPL. USPL will install. If you are using Windows Vista you will probably have to update the drivers (See the thread).
Once USPL is running install the Original HTC 1.56-ROM.
but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...
nobody else can help??????
Try to take out the battery for one minute or two, then see what happens when switching on.
If ok (usual start) make usual normal bootloader state, and see what is your SPL. Then decide which flash you have to do.
Mr. Nick said:
but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...
Click to expand...
Click to collapse
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1
please help me!!!!!
dalamario said:
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1
Click to expand...
Click to collapse
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.
from my experience with HTC Wizard and what you are describing it
sounds like
your battery is very close to dead
you need to find a way to recharge it
your phone is protecting it by shutting off
also i don't know how valid this is for the Blackstone
but the wizard would not charge in tri-color mode
(again for battery sake)
so make sure you have a nicely charged battery (buy a spare or a table charger)
and then try to flash something again
P.S. i don't know how one sentence cries for help peppered with EXCLAMATION points encourage anyone to help you
nguyenbathanh said:
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.
Click to expand...
Click to collapse
A clarification of the above post. When you have 3 colors (actually 4 with white color) and USB on the white band you have to start blac_uspl.exe. That will replace the original bootloader of your phone with cracked temporary bootloader named USPL. At this stage it shall no more give errors and you may flash it from the PC or from the memory card.
The suggestion for the battery also seems fair.
Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
You have to copy the BLACIMG.nbh on the microSD using a USB card reader, not your phone. Then with the microSD on the phone, in the tri-color screen, it will automatically flash your ROM, if you don't have low battery of course.
If you want to use USPL to flash a coocked ROM (for your original official rom is not needed). Your phone have to stay at tri-color screen for more then 10s.
Perhaps your problem is a low battery as someone already suggested.
Do you have tried to remove battery and put it back, let the phone off and charge it with the wall charger?
lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry
wow
Mr. Nick said:
lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry
Click to expand...
Click to collapse
LoL
Dont stress so much next time. When your stressed out you dont think with a clear head. Glad it worked out for you.
The changing of ROM only seems can not brick your phone. Only unsuccessful changing of SPL can. Until SPL is OK you may ever flash new ROM.
Hey guys i have a Imate k-jam..but its stuck like hell..i mean i tried just about everything i could to get it out of bootloader...whenever i press the power button the phone just automatically goes into bootloader mode..and nothing loads..i tried buttons roms..but it stuck at 98%..den i tried the other rom in a walk thorugh and it upgraded and changed my IPL from 1.01 to 1.06 (SPL is the same 1.01) so what should i do? I tried to install a official rom from Imate support but it says that it cant be installed in my device ..i even tried the SD backup method but it doesnt work as well and the app (on computer) just hangs even though it shows the table and other allocations.. PLZ HELP!
sephiroth_vg said:
Hey guys i have a Imate k-jam..but its stuck like hell..i mean i tried just about everything i could to get it out of bootloader...whenever i press the power button the phone just automatically goes into bootloader mode..and nothing loads..i tried buttons roms..but it stuck at 98%..den i tried the other rom in a walk thorugh and it upgraded and changed my IPL from 1.01 to 1.06 (SPL is the same 1.01) so what should i do? I tried to install a official rom from Imate support but it says that it cant be installed in my device ..i even tried the SD backup method but it doesnt work as well and the app (on computer) just hangs even though it shows the table and other allocations.. PLZ HELP!
Click to expand...
Click to collapse
u prob. d/c ur cable when you were flashing a rom
this happened to me
the solution for me was to just reflash a rom
Hello,
sephiroth_vg said:
Hey guys i have a Imate k-jam..but its stuck like hell..i mean i tried just about everything i could to get it out of bootloader...whenever i press the power button the phone just automatically goes into bootloader mode..and nothing loads..i tried buttons roms..but it stuck at 98%..den i tried the other rom in a walk thorugh and it upgraded and changed my IPL from 1.01 to 1.06 (SPL is the same 1.01) so what should i do? I tried to install a official rom from Imate support but it says that it cant be installed in my device ..i even tried the SD backup method but it doesnt work as well and the app (on computer) just hangs even though it shows the table and other allocations.. PLZ HELP!
Click to expand...
Click to collapse
Do this:
Step 1. You`re phone is in bootloader mode (3 color screen) ok? Connect your phone to PC.
On Desktop go to My Computer icon -> Right Click -> Select Manage from the list.
Computer Management -> Select Device Manager.
On the bottom of the list you must have Windows CE USB Devices, if it`s there then you`re phone is connected! If you`re phone ain`t connected please right click on Human Interface Devices, and click on Scan for hardware changes!
Step 2. Go to http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades and get the Aku 3 Official ROM and flash it to you`re phone. (T-Mobile UK 3.8.2.1 WWE (AKU 3.3 & 3.0) OS:3.8.2.119 Radio:02.69.11)
In case you don`t have battery more than 50%:
Step 3. Let`s charge it! Phone must be off. Put the charger in... and hold the power button until you`re phone starts charging. It take`s about 10-15 seconds. Max. 30 seconds and some times 1 minute.
If this doesn`t help you, please do this again: http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Regards! & Good Luck!
eXPLOiTeD said:
Do this:
Step 1. You`re phone is in bootloader mode (3 color screen) ok? Connect your phone to PC.
On Desktop go to My Computer icon -> Right Click -> Select Manage from the list.
Computer Management -> Select Device Manager.
On the bottom of the list you must have Windows CE USB Devices, if it`s there then you`re phone is connected! If you`re phone ain`t connected please right click on Human Interface Devices, and click on Scan for hardware changes!
Step 2. Go to http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades and get the Aku 3 Official ROM and flash it to you`re phone. (T-Mobile UK 3.8.2.1 WWE (AKU 3.3 & 3.0) OS:3.8.2.119 Radio:02.69.11)
In case you don`t have battery more than 50%:
Step 3. Let`s charge it! Phone must be off. Put the charger in... and hold the power button until you`re phone starts charging. It take`s about 10-15 seconds. Max. 30 seconds and some times 1 minute.
If this doesn`t help you, please do this again: http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Regards! & Good Luck!
Click to expand...
Click to collapse
the phone doesnt giv any nidication tht its charging...and when i connect it the ruu doesnt detect the phone (it is shown in device manager though)...and my device is CID locked (aka no chnages made to anything since it was bought).. the only indication that its charging is that the mobile gets a bit hot after a while..and i guess that means its charging..
also the upper right hand corner there is ruu or rru written in the corner..(in bootloader)
Hello, Maybe this helps....
sephiroth_vg said:
the phone doesnt giv any nidication tht its charging...and when i connect it the ruu doesnt detect the phone (it is shown in device manager though)...and my device is CID locked (aka no chnages made to anything since it was bought).. the only indication that its charging is that the mobile gets a bit hot after a while..and i guess that means its charging..
also the upper right hand corner there is ruu or rru written in the corner..(in bootloader)
Click to expand...
Click to collapse
ok... if it`s shown in device manager the the phone is detected by the PC that`s in bootloader mode and connected....
If your phone is CID locked... i have to flash to a official IMATE K-JAM ROM.... you can` find some here... http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
And when you try to charge the phone... orange light must apear, if you say that it don`t indicate... then i think it doesn`t charge...
Regards & Good Luck!
man sadly no orange light.....the screen just turns white when i plug it in...sometimes even that doesnt happen...but a VERY RARE (2 times) the red light flashed for just a fraction of a second...and the links for imate roms are dead..i tried access to the ftp site and there is nothing left in the imate folder at all...anyways..i tried to flash the rom from imate website...even that wouldnt flash..says phone not detected..
help meeee, i just flashed my diamond with this rom: RUU_Diamond_Dopod_CHS_1.39.706.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe and after the restart it brings the message:
Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center.
I've read in other posts concerning this message that i just need to take out the battery and wait 10-15 minutes. does not work for me. i still get the message:
Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center.
I tried to flash it again, but the problem is that the diamond is not recognized on my computer anymore it looks like it doe sent have any usb connection capability any more.
Please help me.
Thank you soo much in advance.
P.s. Is there a combination of buttons to press so i can get the diamond in a flash mode so i can flash the proper OS on it?
come on guys, did i really brick my phone? does anyone have any idea what i should do now?
i had this same problem - take the battery out for about 2 minutes and then power it back on. that _did_ work for me. if you have done it and it didnt work i dont know.
simple question
do you have an original diamond or a dopod?
if you have an original diamond .... you flashed a dopod ROM on it..., did you put a HardSPL on it?
if you have a dopod...really dont know what happens with those ): sorry
Mariano.
i have an original diamond.
yes hardspl was on it.
i can go to the hardreset options by presseing home, vollume down and reset button. but this still doesent let me flash the orignal OS on the system.
what can i do, i really need your help guys!
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
gmesut said:
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
Click to expand...
Click to collapse
I had the same problem
and your solution (dear gmesut) works on it
only i can say thanks
gmesut said:
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
Click to expand...
Click to collapse
good tip,it responded in my hd mini
thanks gmesut
My TP2 stopped working ((((((
I was using it with some cooked ROM (i think it's not relevant what exactly). This morning i had my breakfast and i've got an SMS from an acquaintance. After this i couldn't see my home screen anymore, but i could still use start menu and so on. I wasn't first time as this error happened, so i didn't thought anything and just made a reboot. After this i saw bootloader screen and it was message about missing ROM shortly to see. Nohting else, only bootscreen, hard reset didn't work either. So i came home, connected my phone via USB to my notebook, powered it on and started to flash ROM. As flash was successfully complete, the phone rebooted and i saw... bootloader again!
So i don't know what to do now, anybody some thoughts?
Djablos said:
My TP2 stopped working ((((((
I was using it with some cooked ROM (i think it's not relevant what exactly). This morning i had my breakfast and i've got an SMS from an acquaintance. After this i couldn't see my home screen anymore, but i could still use start menu and so on. I wasn't first time as this error happened, so i didn't thought anything and just made a reboot. After this i saw bootloader screen and it was message about missing ROM shortly to see. Nohting else, only bootscreen, hard reset didn't work either. So i came home, connected my phone via USB to my notebook, powered it on and started to flash ROM. As flash was successfully complete, the phone rebooted and i saw... bootloader again!
So i don't know what to do now, anybody some thoughts?
Click to expand...
Click to collapse
If you have a GSM TP2 try running Task 29 before flashing the ROM. http://forum.xda-developers.com/showthread.php?t=649191 After Task 29 then reflash your ROM of choice and then hard reset to make suer everything took.
Good luck
blutruck said:
If you have a GSM TP2 try running Task 29 before flashing the ROM. http://forum.xda-developers.com/showthread.php?t=649191 After Task 29 then reflash your ROM of choice and then hard reset to make suer everything took.
Good luck
Click to expand...
Click to collapse
Yes, i have a GSM TP2. As you advised, i downloaded Task 29, unzipped it and run ROMUpdateUtility.exe from its folder. After 100% phone booted again to the bootloader, I went to ROM's folder and run CustomRUU.exe from it to flash the new ROM. After "success" i disconnected the USB-cable and started the phone... no changes. I still see the bootloader. And i still cannot hard reset my phone for some reason.
Djablos said:
Yes, i have a GSM TP2. As you advised, i downloaded Task 29, unzipped it and run ROMUpdateUtility.exe from its folder. After 100% phone booted again to the bootloader, I went to ROM's folder and run CustomRUU.exe from it to flash the new ROM. After "success" i disconnected the USB-cable and started the phone... no changes. I still see the bootloader. And i still cannot hard reset my phone for some reason.
Click to expand...
Click to collapse
How are you hard resetting your phone? All I do is power it off then hold the send and end keys and press and hold the power button until a message pops up asking if you want to hard reset. Press the vol up key to reset and after it completes press the vol up key to reboot.
Just a random thought here--is it possible your volume down button is stuck?
blutruck said:
How are you hard resetting your phone? All I do is power it off then hold the send and end keys and press and hold the power button until a message pops up asking if you want to hard reset. Press the vol up key to reset and after it completes press the vol up key to reboot.
Click to expand...
Click to collapse
Yeah, I do the same. I hold the both outer keys and the power button but no message pops up, just the bootloader.
BigWopHH said:
Just a random thought here--is it possible your volume down button is stuck?
Click to expand...
Click to collapse
It might be possible, but if i press it, it feels like its OK. However, is there any method to test all the buttons of my phone?
Any other thoughts? Without phone i am totally f*cked up, cause i am not in my hometown right now and i have to keep contact with my business partners in there.
It sounds like your bootloader is somehow broken, if it isn't a problem with the volume down key.
Try searching for information about the "mtty" utility. It's kinda complicated, but I think it's helped people in a similar situation.
steviewevie said:
It sounds like your bootloader is somehow broken, if it isn't a problem with the volume down key.
Try searching for information about the "mtty" utility. It's kinda complicated, but I think it's helped people in a similar situation.
Click to expand...
Click to collapse
Thank's I'll inform myself about "mtty" keyword. But if u say that the bootloader could be broken, maybe i should try to reflash HardSPL or go back to stock SPL?
Djablos said:
Thank's I'll inform myself about "mtty" keyword. But if u say that the bootloader could be broken, maybe i should try to reflash HardSPL or go back to stock SPL?
Click to expand...
Click to collapse
Yes, that's another alternative, at least you can try it.
steviewevie said:
Yes, that's another alternative, at least you can try it.
Click to expand...
Click to collapse
Now I am encountering bigger problems with my device. I tried to use MTTY ver 1.42 first. I couldnt use it because there wasn't an option to choose USB-port. Yes, i unchecked "Connect via USB" in WMDC and killed it then in task manager. Then i flashed stock SPL ver 0.79, hm nothing new. Then I tried to flash the original SPL, i.e. ver 0.84 and it got stuck by 0%. I waited and waited and waited, so i had to remove cable and the battery. After that nothing worked. No flashing worked at all, even Task 29 gets stuck by 0% every time........ I dont know what to do now.....
Can you get into the bootloader still ?
steviewevie said:
Can you get into the bootloader still ?
Click to expand...
Click to collapse
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
So does it still always go into the bootloader ? It won't boot ? If so, have you tried mtty to try and fix that ?
steviewevie said:
So does it still always go into the bootloader ? It won't boot ? If so, have you tried mtty to try and fix that ?
Click to expand...
Click to collapse
As i said above, i could not connect to the phone through mtty, but fortunately i have another laptop here with winxp on it so it works on it. I typed "set 16 0" and "task 8" and it booted again into the bootloader just like before.
Djablos said:
As i said above, i could not connect to the phone through mtty, but fortunately i have another laptop here with winxp on it so it works on it. I typed "set 16 0" and "task 8" and it booted again into the bootloader just like before.
Click to expand...
Click to collapse
Have you tried flashing a ROM using the storage card method? Might be some error being caused but your computer.
The following was taken from http://forum.xda-developers.com/showthread.php?t=550540
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
You might also want to try flashing from another computer.
Djablos said:
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
Click to expand...
Click to collapse
well it seems that you have flashed back to stock spl since it is showing you spl version (0.79)
which means you will have to hardspl it again in order to flash any custom roms again but it is probably unlikely that it will not work because when you reflash stock spl you are suppose to flash stock rom & radio first before flashing stock spl i'm just guessing i'm not to sure on this 1 i could be wrong though
P.S. - just a suggestion since you have stock spl back on the phone try & flash a stock rom to see if that works
Djablos said:
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
Click to expand...
Click to collapse
Is that maybe the problem ? Did you flash the stock SPL back onto it as you referred to earlier ? Because 0.79 is a stock SPL version, so it won't boot a custom ROM with that SPL.
So is the whole problem that you have a custom ROM and stock SPL ? I hope it's that simple, but fear it isn't.
I hope!
Hello,
if you have 0.79 hard spl,
1. you should install stock rom, not cooked. After go to bootloader mode.
2. Run Rhodium-HardSPL_V2_00R3.exe from http://forum.xda-developers.com/showpost.php?p=4363807&postcount=1
3. Install cooked rom!
It is working!
I hope it will help your problem!
blutruck said:
Have you tried flashing a ROM using the storage card method? Might be some error being caused but your computer.
You might also want to try flashing from another computer.
Click to expand...
Click to collapse
Yeah guys, here's what i did and what i see. Before i flashed stock SPL 0.79 i flashed stock ROM and stock radio. Then i tried to flash stock SPL 0.84 and it didn't work for some reason. OK, then I read an advice from Doo Doo and tried to flash stock ROM again. I was wondering that it worked... but as it got 100% the device entered bootloader mode again! But after this the version of SPL was 0.88
I cannot use storage card method because i don't have any possibility to get access to the card from my PC And I just tried to hard SPL my phone from another PC (winxp) so it didn't work either, stuck by 0%.
Try to older stock rom. Maybe it will install older spl...
Sorry, but I couldn't help this problem! :S