Database Develop

Can't flash Kaiser HardSPL in any way???

Iv'e tryed to flash HardSPL to Kaiser... Downloaded various unlockers/flashers, even SD card solution... When trying to flash over usb with some Kaiser-HardSPL.exe - after entering tricolor mode and when progressbar appears it always stuck on 0%, and nothing happens... Update utility shows error (Rom update utility encountered communication error or smth.) and sugests me to do recovery. Tryed everything - SoftSpl1.56, Softspl1.93, SSpl-kais...
Other method i've tryed - SD card
Iv'e followed instructions, formatted card, copied those two files (http://forum.xda-developers.com/showthread.php?t=420683) to sd card, but after resetting Kaiser it only shows "Loading..." and hangs... no restart, nothing... just "loading..." on screen...
Bootloader menu shows following versions:
KAIS130
SPL-3.29.0000
CPLD-8

somehow... after trying another 1000 -th time... it just flashed...

Have exactly the same problem, tried all other solutions! any idea on what the last method was that worked?

When flashing via USB it will hang at 0% (and fail w/ 260 error on PC side) if the SD card is left in. I've made that mistake more than once.
Remember to remove SIM, too.

I don't have sd card and I've got the same problem...
Any ideas?

I have the same problem. I want to upgrade Hard SPL 3.24 to newer version. I always get 262 error. Also tried all possible ways (MicroSD uses FAT32, but I didn't formatted It, because I don't have SD adapter).
Sometimes It's shown that flashing complete, but HardSPL version still is the same.

Read you noobs
FOLLOW THE DIRECTIONS
http://forum.xda-developers.com/showthread.php?t=396922

latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time

Biker182 said:
latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time
Click to expand...
Click to collapse
good, also check the contact pins, sometimes they get bent.

hmmm...
i STILL can't get hardspl to work at all...just get stuck at 0%

sabzi43 said:
i STILL can't get hardspl to work at all...just get stuck at 0%
Click to expand...
Click to collapse
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.

aaaaahhhhh
WarByte said:
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.
Click to expand...
Click to collapse
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!

sabzi43 said:
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!
Click to expand...
Click to collapse
copy sspl.exe into your device and run it then you can flash with CustomRUU
to much better you are using ActiveSync on Windows XP

Thanks so much!!! i got it to work!!!! i actually used a jump spl instead, but i now am running win 6.5 on my kaiser!!!!!!! and i'm beyond stoked
THANKS Y'ALL!

Unbrick Trinity From SD

Need a favours over here. Recently, i bricked my trinity. P3600 more precisely Dopod D810 (i flashed wrong ROM -> Unpacking cooked rom for trinity but i merge it with -Hermes cmd in NBMerge! houh... so stupid! ). Soo... just not what i expected, Rom flashing stop on half, SR my trin and tada.... 3Color screen bootloader popup! haaarggg, i try flashing another rom using any rom that has same CID *official or cooked rom* (some are 100% thru, but someother not) but like usual it won't start the windows (just blank/black screen with green led[ always on!) Never been like this before! Have been flashing several times using any cooked rom by great chef on trinity but this time! :doh: damn it! my bad.
i found solution on the forum *Unbricking Trinity Stuck on Bootloader* but since my usb port can't be detected on my vista/xp machine, whether i disable AS and changed my usb cable it doesnt work at all, on mtty too! so i can't use that utility. i try run install sspl olipro 1.3 but it never changed my spl at all. now i can't use my trin at all cuz allready dead.
btw this is the info on trin 3color screen bootloader:
IPL 1.00
SPL 3.20 OLIPRO
anysolution for bringing back my trinity from the death? maybe a tools/utility to unbrick trinity from SD or something like that, which not involved any pc connection, without bring this devices to htc center of course.
I hope any expertise on this forum would helped me sort out this probs.
Sorry for my english and thanks for reading my post.

Read this :http://forum.xda-developers.com/showthread.php?t=308691 download splxploit-windows.zip (935.1 KB, 7619 views) put phone in bootloader run splxploit when bootloader change
After this download full rom here is link:http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
Then flash full rom bat do not disconnect usb cable in any step.
Before use any step disable active sync.

Usb are dead
Gsmhacks thanks for ure reply. I have tried that one, and lot read ing on wiki. But since i cant use the usb i cant use that splexploit whether on live linuxcd, or .Net version even win version. The usb port cant be opened . I think i broke the usb pin. From the beginning everytime i flashed my trin i never used ruu utility, i always do the sd card method and that is the best and easiest method and it works for me.
I just curious perhaps can anyone or is there any utility to unbrick trin via sd card. I knew a lot a people has bring their trinity life from dead by using htc stackflow splexploit. I hope that was work for me too! Too bad my usb are dead. Damn!

Here what you need bat only work if you have hard spl
If you install hard spl before brick trinity you can use SD CARD to flash trinity. YOu need to formate sd card to FAT32 with Card Reader donwload full rom here is link: http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
then extract and file RUU_Signed.nbh rename to TRINIMG.nbh and copy it to the root folder of your miniSD card.
Here is full instruction again also first format sd card to FAT32 !!!! VERY IMORTANT to format sd card to FAT32 or all other step will not work THEN:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (or you can also use winrar via wine).
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
and you will flash and unbrick trinity bat this only work if you install before this hard spl i mean cid unlock trinity. if not you must fix usb port.

That will work? I hope so
Ok then i'll try flashing using that rom. Oo, i have install hardspl btw and so far flashing using sdcard method no probs. But after i bricked my trin flashing doesnt smooth like be4. Always gave me error 0018003 update fail on the halfway, i guess because i have bad nand on trin and probably cuz cooked rom.
Can u give me another link, perhaps on xda ftp. rapids so slow 4 me. Btw i have download dopodasiawwe official rom on xda ftp *twice but still when i tried to run the package it gave me corrupt archive integrity fail w!f.
Thanks gsmhackerns, i downloading the package now!

Perhaps you can find a way to make a goldcard for Trinity?
See http://forum.xda-developers.com/showthread.php?t=437996

That's what i looking for! Thanks.
Humm, superb. Yay, great! Thank you stepw. Even its for elf with a little mod i hope this will work. Once again thank you.
Stepw, i have tried making the gold card, everything went ok. I have temp. cid *supercid* but the probs now is i can't download http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.execan someone uploaded to somewhere else. Rapidshare crap! perhaps on xda ftp.
thanks!

goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also

cmonex said:
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
Click to expand...
Click to collapse
Indeed. Youre right cmonex, it doesnt make any difference at all 4 my trin. After several tried using and making goldcard 4 trin, finally i made working goldcard4trin, but gosh it still stuck when i tried to update the os (update os fail) humm anyone.

Sorry for wasting your time with Goldcard, I have overlooked that you have a hard spl on your Trinity. In this case goldcard doesn't make a lot of difference.
And there's no trindiag.nb to the best of my knowledge that could be used instead of SSPL cmonex is suggesting to run from SD.
Back to the topic, sounds like you have some "bad" blocks in flash and OS can't be flashed. Bad blocks can be reset with "task 2a" command, see this thread for more details:
http://forum.xda-developers.com/showthread.php?t=330496
The question is how to run it without USB and I don't have an answer for you
Some people have previously mentioned they managed to flash smaller OS images when larger images failed, perhaps if you try flashing some minimal vanilla ROM, it will succeed?

Bad NAND, Yup!
Ya... as i mention before yup i do have bad nand block on my devices. Using manila rom with smaller img size the flash went 'OK'. But it doesn't boot at all infact just black screen with green led on.
Okay the only solution probably use mtty and do task 2a if i'm not mistaken. But like you said "The problem is the USB port". I think the port is ok cuz i already tested it connecting my usb to my trin without inserting the battery and the red led *magenta* is on. humm, weird!
But if something can make it working without involving any pc connection it would be a great achievement. hahah! well i supposed i have to put my trin on bunker before someone can make it happens
I asked SEA in my country and they recommend me to changed the machine it self and they charge me around US $160 ho...ho.. too "wideeeeee" for college boy like me

Same problem, i flashed the rom
RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship
and after that i tried to flash a new radio!
power+cam and the cell phone did not show usb, then i used sspl to rum the radio but it locked at 0%
after that it is stucked at bootloader screen
ipl 1.0
spl 3.20 .....
but no usb and no sd card !!
did i lost the cell phone?
there is no jtag ou something like that ?

so now... you still want this SSPL? i'm thinking of patching one up to automatically run task 2a maybe. or just restore stock spl for warranty service if that's what you have in mind. but you didn't really reply to that offer?

Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english

Needed!
Cmonex, sorry for longtime haven't seeing this thread again. okay i really need your help btw if you willing to help me. The spl your talking about perhaps can sort out the probs (i hope) at least we tried. as for task2a cmd to clear the bad nand block is none usefull for me since usb conn. are definitely drop dead.
how about patch the SSPL to do task2a cmd to solve the bad NAND block first.

dinizbruno said:
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Click to expand...
Click to collapse
no usb, no sd, no chance sorry. jtag it or get it serviced or get another phone.
as for jtag, hermes jtag has been worked out by scholbert. trinity is probably the same, but you will have to find the pins. the rest of the process will be the same.

Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,

The O.S is more important to these operations than can be stressed - for a 99% safe flash Win XP is your best bet , I have had nothing but error 260,270 halfway flashed roms and usb faults running on vista and since I had my original bricking episode - NOTHING , I repeat NOTHING including genuine roms has flashed without a recovery or at least without doing something strange in the process - SPLXPLOIT has been a saviour here , without it I would've been lost.
Cant the O.P simply use another machine to test out the USB theory ?

ALIVE AGAINnnnnnnnnnnnn!!!!!!!!
My p3600 was stucked att bootloader, and wont give "usb" and do not read TINIMG.NBH (tried on elf with ELFIMG.nbh and the card was great)!
I did a golcard with the post on elf about it and the cell with the gold card inside was the same, no trinimg.nbh and no usb.............
BUT..............
with the goldcard inside, turned OFF, i placed it on the usb cable off the pc and the device booted to the bootloader screen, but this time he got "USB" , before flashing anything i removed the card , and putted switched off in the usb, booted with "serial" with card and pressing power and then placing usb still "serial" message!
I putted the card, did not switched on , placed on the usb and waited for it to boot for it self , and for my surprise "usb".
Flashed stock rom, and it booted nice!!!
Please try!
saved my day!

sidekraouf95 said:
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
Click to expand...
Click to collapse
I have to know how to repair my phone please... nobody can explain precisely how to put my phone on bootloader using my sd card directly from my computer under vista...???

Help! Problems flashing X1

Hey everyone. I'm tearing my hair out trying to get this sorted but I just don't know what to do!
So, when I got my X1 as everyone on here should do, was flash my X1 with the HardSPL and some custom roms, this was a few months back. Then, shock! Horror! My case went and broke, (cracked near the volume button build W44) so I sent it back to SE for repair. I sent it back reset back to defaults but left the hardspl on there.
SE sent me a brand new phone (I think... This one says under the battery build w50, but the battery says w32..) I received it today. I thought it would be my old one repaired but SE had other ideas. Booted up and have Image Version: 1.03.931.10 and HardSPL 72.000 I think I said that correctly...
Now since sending it for repair and receiving it back, their seems to be quite a few wm6.5 roms floating about, and obviously I can't use the stock software as that wouldn't be right!
Now I have tried flashing the hardspl to the phone through my Vista PC and all it keeps giving me is connection errors. I thought maybe it was already flashed so I tried flashing just a rom, and that just made the phone get stuck on loading (flash by memory card). I thought it might be Vista, so I tried doing it on my other PC (XP) and I get the same issue. This bloody thing won't flash!
I have had "Connection Problems" - "Update Errors" with different numbers. The current one being Error [260] CONNECTION.
Now I have been searching around through the hardspl thread and other places trying to find out what I need to do or how I can fix it, but everything I try doesn't make a difference. I did read some other people with recently repaired phones having the same problem and perhaps SE have put a new spl thingy-ma-jiggy on there. (Please forgive the technical jargon, I have no idea what im on about.) I have also tried the ticking/unticking advanced network functionality, but that hasn't made a difference either.
So by the end of typing this, I have little hair left. Let's hope you can all help, before I have none left!
I would appreciate ANY help! Really.
Just wanted to add, I was at first getting the phone to a loading bar when flashing, but it would stay at 0% then flag up an error on the PC. Now after the tri-colour bars, the phone just sticks on Loading...

Well just to update. I have been trying to sort this since posting. I flashed the rom to an old UK generic one, as I read in another topic people had to do that before HardSPL. Done that, and tried flashing the hardspl. Same thing, just getting connection errors.
I tried going into bootloader and running the hardspl from there. It works and the phone gets to 10% and then gives an UPDATE ERROR. The phone is now bricked, and I have to reflash the original wm rom to get it back.
Though the Tricolour screen now shows 0.52.Olinex
Any ideas?

Shameless bump for help.

very stupid situation.
i have the same situation in puncto of flashing.
i get my phone three month ago.
after hardspl i .... sorry, no hardspl ... the phone says at 0% bla bla bla
i solve the problem by consulting one night absolutly stressing again and again and again .... google ... xda ... google
than 3 thinks at one time was the solution:
0. need activesync - connect !!!!
1. SDA_ApplicationUnlock.exe for desktop pc
2. enterbootloader.exe for pocketpc (please, the right version, it exist for eten too, but we need the xpediaversion ..)
3. changing registry-entries
how to:
activesync-connect, than copy "enterbootloader.exe" to pocketpc. it must be root, not sd-card. use a pocketpc-registry-program to change these values :
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies\0000101b = 1
if not exist than add the key.
now, start desktop-program, follow instruction EXCEPT reboot.
start "enterbootloader.exe" on pocketpc. now, you can install hardspl and the device is flashable for ever.
thats works on me, hope it could help you too.

Thanks for the reply. Not had time to try it till this morning. Ok so, after spending about an hour trying to find the correct enterbootloader.exe I finally realized, that the hardspl package includes it. *Duh!* So that was time wasted.
I changes the registry values as you said with Resco registry editor, and follower the unlock then enterbootloader.exe Start HardSPL package. Starts to install. Gets to 10% then I get
ERROR [262] : UPDATE ERROR
The rom update utility has encountered communication errors during the update process.
So im open to suggestions if anyone has any. I just can't understand why it's not working. It's not a problem with my computer or cables. I flashed the phone before I sent it for repair and I have tried doing it on two computers one with XP 32bit and one with Vista 64bit.

hmm. would u like to install a custom rom, or a stock rom?
msg me, and i hope, i can halp u.

I want to have the hardspl on there so I can flash custom roms.

If it's a case of the software/firmware/hardspl whatever you call it, has been updated by SE. How would one go about getting it flashed? Would we have to wait for an update HardSPL to be released?

U read this thread?
My first hardspl was from this thread. New X1 will come tomorrow back from SE (vibration was defect +++ some more problems with case), and i will try it again with this thread.
hope, this will help u mate.

Yeah, I have been through that thread with a fine toothcombe trying everything suggested to see if I can make it work.
When you get yours back, if you have to do anything out of the ordinary to get it to flash or can't do it. Please come and let me know in this thread. If they have updated yours like mine, and yours won't flash, at least I won't be the only one!

k, i will msg u tomorrow around 2pm.

Cheers.
In the meantime. Does anyone have any other suggestions I could try?

Bump, for some help.

now i know, what is exatcly your problem.... <--- SAME Problem
i hope, i will find a solution and msg u then. if u´ll got a solution for this prob, msg me too plz.

Solution found in this Thread!
Download this and unzip it to your device. ++ run it. It will start your X1 in Bootloader menu and say "0.52.OliNex".
Then start hardspl while X1 is in Bootloadermenu....
FINISH =)

Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.

vwrmic said:
Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.
Click to expand...
Click to collapse
hmmm... it works fine on my new x1. are u sure, that u start the ssplmanual on your x1 and not on your computer?

Yea, im not sure what the problem was with it. Thankfully I have it done and dusted today! Because I flashed it earlier to an older official version, and you said you got it working. I presumed you had - had yours flashed to the newest version due to it being off for repair. So I reflashed the official update and fully updated it. Then tried hardspl which didn't work. Tried with the advanced USB thing off, tried again with how you said you did it above, and Viola!
Hip hip hoorah! Thanks for the help. Can finally use me bleedin phone now!

no problem mate hf with your x1

hello,
i see smilies and yea's ...
for me to understanding (for next time or other users):
1. complete official update (if exists)
2. flashing (hardspl) without "advanced usb"
thats all?
cool.

Upgrade to 6 stuck on windows loading

Hi,
I got given a couple of Treo 750 phones. Both on the Optus Australian Network so I scratched around for days and found the upgrade software. Shows update 2.27
1st one went perfect.
2nd one on same computer got through copying files and executing update and stalled at the start of completing update.
I got the Windows mobile screen show and it just was not loading for ages. Previous one loaded and then asked for input of Date, touch screen settings etc.
The installer can be re run but says no USB connection at the moment.
I have done a hard reset and get the palm display then locks on the Windows Mobile screen.
I saw procedures to use the Mini SD card but the cards I have won't work in any treo, they are not SDHC type but standard 2G ones.
I next found the recovery tool but holding the left lower button and then hitting reset did not work but does work on my good phone where it shows the coloured bars and SPL....
The left button is a bit dodgy so I suspect it may be faulty. Is there anything else I can try?
EDIT: Ok I pulled apart the phone, looks like it had a hard life as broken case around two screws and they would not unscrew easily. Found the tiny button had dry solder joints. Fixed that up and was able to recover using the reset proceedure.
Phone now working.

could you explain in more detail what you did. thanks man

webafile said:
could you explain in more detail what you did. thanks man
Click to expand...
Click to collapse
What would you like to know?
Once I physicaly repaired the phone as indicated in the edit I was able to hold the left hand button (which was faulty) and the reset at the same time that allowed me to get into the SPL mode and recover the phone.
I understand it very little and most posts on these forums are over my head.
I would like windows 6.1 but there is so much information that seems to conflict that I don't know I am game since it is now working on an official 6.0 Optus version.
I am happy to help but if you can maybe tell me where you are at the moment and what you want to acheive and what you have tried I hope I can fill in the gaps for you.

because im new to this to and i got stuck in the windows screen also. so i would like to know what to download and where from and step by step if you could please.
thanks man

webafile said:
because im new to this to and i got stuck in the windows screen also. so i would like to know what to download and where from and step by step if you could please.
Click to expand...
Click to collapse
Ok to start with what country are you in and what telco were you with eg Vodafone etc as you will need that as a start.

USA and im with AT&A

Try the method describe in the thread below - Mine work
Hi, you might want to try this method
Follow it one by one and do not skip a step
http://forum.xda-developers.com/showthread.php?t=460783
I just did mine last Saturday (it was a Vodafone phone)
AT&T should be easier since the Windows 6 ROM is easier to get
If you'd like to update to WM 6.1, you should upgrade first to WM 6
Something i read about the radio not working to full capacity if you upgrade straight to 6.1
As for the WM 6 ROM, i'm sure you can find it
Good luck

Hi All,
I have a Treo 750 and it WAS running WM 6.0 Professional (OFFICIAL) and I got it onto the phone and then tried to install WM 6.5 and then I downgraded to 5.0 and tried to update back to 6 and it bricked my treo, any of you wonderful xda ppl have any solution?
Also, I have tried installing the ROM again (via SD updater) and it looks like this:
SPLASH1 OK
BOOTLOAD OK
GSM OK
Micro P OK
EXTROM FAIL
OS
Update Terminate
UPDATE FAIL
I cant install the windows installer one as WMDC 6.1 or ActiveSync 4.5 WILL NOT show the device up on the computer. I have Windows Vista Home Basic, and when I tried MTTY, the only ports I get are COM1, COM2, and COM3. I can't get the usb to show up. Even with MTTY 0.01 when I got the USB connection, it would not open. Is it Vista? Or am I not doing it right? ANY HELP WOULD BE APPRECIATED TO GET MY POOR TREO BACK!!!!!!!!!
Thanks
~Mike

Try this?
http://forum.xda-developers.com/showthread.php?t=427519

simunlocktreo said:
Try this?
http://forum.xda-developers.com/showthread.php?t=427519
Click to expand...
Click to collapse
Is this universal (i.e. Hermes/BA/Trinity) or just for the Treo 750. I think what bricked it in the first place was installing a custom rom by veisen (WM 6.5)
~Mike

Didnt Work
That one thing didn't work. It keeps coming up ERROR 226: FLASH WRITE ERROR Anything else???
~Mike

[Q] HardSPL Problem!!!

Hi everyone,
i've got a problem... i have tried to flash hardspl (bootloader) on my x1 but it doesnt work.
i have tried it like i read in the forum in different threads but i cant enter bootloader and when i start hardspl on my pc and take step by step as the program says... after the progression bar came - my phone display goes black and the front panel starts to shine and after a time i get a connection error on the hardspl program...
can anybody pls help me????

did you take out your micro sd card out of your phone?
That was my problem...........

I too have the same problem. I follow the instructions and HardSPL checks my x1. Then when I hit update (the rom). It gives me either error 202 or 246. Not sure why. Anyone?
EDIT: Problem persists with or without sdcard

hard spl
hi
i had some problems !
here is the best info
try every thing and search and read what i understud was that some phones have different ways to get in to the right hardspl mode i all most gave up and then it workt
DONT GIVE UP I WAS ON IT FOR 2 WEEKS
THE WORST THING IS I DONT REMEMBER WHAT I DID SORRY !
HASSE

tilsid said:
I too have the same problem. I follow the instructions and HardSPL checks my x1. Then when I hit update (the rom). It gives me either error 202 or 246. Not sure why. Anyone?
EDIT: Problem persists with or without sdcard
Click to expand...
Click to collapse
Several time ago i got that error too, but i never give up. Try another hardspl for xperia, when u click it, it will auto generate to extract some file, just click romupdate utility and follow the same procedure.
If still got some error, try install it from a fresh computer with usb 2.0 installe and active synch.
You just got that error becouse there is some miss connection with another usb device.

UPDATE: it worked
So I did a hard reset on the phone (settings-> clear storage) and then tried again. Worked like a charm. Installing ROM right now!
Thanks everyone!

Moved to X1 Q&A as not Rom Dev

it still not work...
i have tried all you write me...
no it says first "no file found" and trys to update over usb and than it says again connection error...
what shall i do?