i ccan't figure this out does anyone can tell me the procedure?
were to download and how to install??
Do a search. on either google or on this forum before asking plz.
This question has been answerd before.
But sins there was no thread that was acualy called like your question ill post the answer and maby next time when someone search they will defenetly find the answer
Go to the link below and download the program and install it on your computer.
When its done it will install it on your phone aswell. (so keep it connectded to the computer while you install it)
http://www.microsoft.com/downloads/d...displaylang=en
Go here
http://www.microsoft.com/downloads/...49-3C6B-42F1-9FD9-0041345B3385&displaylang=en
If you read the instructions, it will tell u.
This package uses ActiveSync 4.0 to update the device. Before running NETCFSetupv35.msi, connect your device to your PC. If your device is not connected, ActiveSync will store the CAB file and will not install the package until you connect. If you are not using ActiveSync, run the CAB files on the device that correspond to the device–specific CAB files found in the install folder.
For now, it's not possible to download directly the cab file from MS site
google for the following files:
- NETCFv35.wm.armv4i.cab
- netcfcfg.cab (saves yourself from editing registry)
You will identify trust-worthy locations easy
Easier than you can imagine.
Search MODACO forum ( www.modaco.com ) NETCFCFG.cab and NETCFv35.vm.armv4i.cab
Install both and you will have a simple application in program menu to choose between net 2.0 and 3.5. DONE
You can also choose to use 2.0 for some applications and 3.5 for other
thnks y´all i found it on modaco, got it worked!!
pls help, I can't install it
it writes: "installation error. stop all applications and processes, maximize available storage space, and run installation again. Support info: 3"
I cant even uninstall it, and I get this msg always
"installation error. stop all applications and processes, maximize available storage space, and run installation again. Support info: 3"
Solution: I kill Kaiser Notification and then I can install .NET Framework without this problem. This app. using .NET Framework.
So I think the solution is in closing/killing all running applications.
What is the "kaiser notification"?
I have the same install error.
Thank you.
i have the same installation error as the last two posters. i tried killing every program i can and i still get the error
me too !......still can not install netcf v3.5 !!
After 2 days searching high & low through internet all discussion session, still can not find a solution. Therefore I made a self tracing and tried all kinds of method, at last I found a solution without doing a hard reset !!
rename mscoree.dll under windows\ to mscoree.dll.txt
re-install netcf v3.5
no more any error code comes up
thats it !!
I am running a tytn II, with the same problem. Install, i get the error. I can't uninstall, atleast not when I try through the 3.5 installer (remove or repair) or the "remove programs" on the kaiser.
I have hard reset the phone 2x,and regardless of whether I am installing from the exe or the cab file on the phone, still get the same error as everyone else.
This past time, i tried changing the name of the mscoree.dll under windows\ to mscoree.dll.txt and mscoree35.dll to mscoree35.dll.txt
same problem. I'm really beyond annoyed. Can someone help?
have a sprint diamond, how do i check which version i have and if its the newest?
it seems like all the programs i try and install say it requires a newer version than the one installed on the device but its only a month old so im not sure.. any help would be great..
thanks!!
I have the same question. I've searched all over and can't find an explanation of what .Net 3.5 is or how to find out if I have it already. I have a Sprint (CDMA) HTC Touch Diamond. Thanks.
I had the same problem on my HTC Kaiser, but I found a solution.
I found a program that acts like safe mode on a computer.
So if you install that program and restart in safe mode (you need to select safe mode when you boot), you will be able to install the compact framework 3.5.
Probable some locked files prevent the normal installation.
The program is an evaluation version, limited to 14 days, but since you only need it for the framework, you don't need to keep if you don't want to.
The app: SafeMode 3
...still not working on my touch diamond.
i've renamed the dll and tried the safe mode app. But I still get the same error.
btw: i have this problem since i installed a cooked rom.
Thanks. Was also having the install issue (I had previously installed and then removed 3.5 but good old ms clearly didn't remove correctly).
Renaming mscoree.dll worked (I tried mscoree2.5.dll before but that didn't work as it was in use so I couldn't rename that).
Glad it worked, was facing dropping back to previous backups or installing a task manager to kill processes (a good task manager program will show all your processes), just to reinstall 3.5.
another thing that goes wrong with the 6.5 wm and tf3d installed:
when you go to the movies, and you put your phone into vibrate, with the left volume keys, the phone goes into vibrate fine,
but when you set it back to full volume, the next time someone calls, it only vibrates, you have to go to: Settings, Sound and change the ringtone manualy to make it ring again...
Sorry, Wrong Forum...
Related
Having problems as of late installing certain programs
So far;
Pocket CM (all versions) don't install i can choose the location (and i have tried them all) and then i get an error that it couldn't be done
Bandswitch 2.4.1 just says install was unsuccessful as I click on the cab
Mobile justice - same thing, even after installing certificate
EDIT: another one on the list Reperion same issue as Pocket CM
EDIT #2 Looks like its a problem with either my Storage Card or Transferring to it via Activesync
I have tried moving the cabs to the device and install (instead of the storage card) same thing.
Tried after soft reset..same thing
At first i was going to just go into the individual threads for help, but since its now 3 programs, something is wrong
Trying to see if i am missing anything before doing a hard reset.
Any help would be great
Hi all,
I am facing a weired problem,
I have installed an application, it was installed very well, with no problems at all.
But when i flashed it with a new ROM, i have tried to installed that application again, i keep getting:
Installation of 1 ACERT_ARB.CAB was unsuccessful
shortly the whole package doesn't get installed at all.
I went through the program files, deleted any old stuff, tried to reinstall, but the same problem
i have put the old ROM back, but still no luck
am i missing something here? any advises please?
regards
i get that issue every now and again. I usually have to either use a different file explorer or do a soft reset and try again.
Thanks for sharing
i have found the solution finally
the current ROM doesn't support the CAB file i was installing,
i needed to do the following:
remove the SD card
reinstall the compatible ROM which support the CAB file
i hoop it it heps other they may had the same issue
reinstalled rom...
still problem continue
has a other solution?
I recently had this problem when trying to install a couple of CAB files. It appears that something was running that the CAB was trying to update. So, for example, I was trying to install "Inbox Extender" and POutlook (and/or tmail?) was running. Once I killed that, I could install the CAB.
CAB won't install suggestion
I saw this with several cabs that I ran using Resco Explorer and I had Kaiser Tweaks set to not delete the cab after install. The solution was to deselect that setting in Kaiser Tweak, ket a fresh (never run) copy of the cab file and run it using the generic file explorer. It has worked every time since then.
Acert_Arb.cab is no more working
NightStar404 said:
Hi all,
I am facing a weired problem,
I have installed an application, it was installed very well, with no problems at all.
But when i flashed it with a new ROM, i have tried to installed that application again, i keep getting:
Installation of 1 ACERT_ARB.CAB was unsuccessful
shortly the whole package doesn't get installed at all.
I went through the program files, deleted any old stuff, tried to reinstall, but the same problem
i have put the old ROM back, but still no luck
am i missing something here? any advises please?
regards
Click to expand...
Click to collapse
hello buddy,
Microsoft has made ACERT_ARB.CAB for limited time I think so. Now Microsoft has decided to claim $ for their OS windows mobile. They are working with www.penreader.com
ACERT_ARB.CAB is no more working.
visit this for more information:
http://social.microsoft.com/forums/.../thread/fa78dad9-7ede-472a-af0b-1f8dddaf7900/
http://www.penreader.com/pocket-pc/arabic/Language_Extender_Arabic.html
I cant install anything, .exe, cab, nothing. Please help!!!
I also can't install and run any .cab , .exe or haret. help us
I have Tytn II with L26_Kaiser_Diamond_V5 (Hybrid 3.29.707) Rom.
Installed Calligrapher 8.6 and unable to select either writeanywhere or writepad from the SIP menu or by anyother means. In short after installing calligrapher and softresetting i am not able to use it.
Can anyone please help
Don't know if it will work or not but, you might try installing the Default_IM_WM5.cab or SipChange.cab and see if one of them will let you select it.
no success
^^ Solution -- not working
Assuming-
1. you installed with the desktop loader EXE
2. you had an active ActiveSync session and your phone was properly connected and
3. you selected to have both Write Anywhere and Write Pad SIPs selected when finalizing install to PPC
You should have entries for both in the SIP and a folder under programs with the EXEs. If you cannot find any of this you haven't properly installed the program.
Reconnect your phone and make sure you have an active Sync session, run the setup EXE from your desktop and follow the instructions that appear on your screen. (See pic)
Yes of course
The program was installed from the desktop pc and softreset was done. Both writeanywhere and writepads are installed and it is shown on the list of SIPs (when we click small arrow near the keyboard icon) but unable to select them. I am able to access the options menu of calligrapher from Start>settings>system>calligrapher.
ok now do this
http://forum.xda-developers.com/showthread.php?t=301433
Please see the image
boomermax
I had done that yesterday itself but the problem is menu showsup faster but unable to select writeanywhere or writepad.
so basically I've been no help at all...LOL
I'm sure you've uninstalled and reinstalled and have probably have redownloaded a fresh copy and tried installing that...
what happens when you select it from programs? Nothing?
Reinstalled
Reinstalled few times, when i select from programs nothing happens adn i don't know is it the problem of the L26 ROM or Windows 6.1 or the Calligrapher 8.6 --
if some one can help i will be grateful
Earlier also there was some problem without a solution for someone
http://forum.xda-developers.com/showthread.php?t=353077
try disabling the cube if you have it. I had this problem with transcriber, worked after I disabled the cube.
NO CUBE
I don't have cube but transcriber is working perfect only i have problem with calligrapher
still probably no help
have you tried having the installer remove transcriber from SIP during install?
Yes of course
Even without transcriber calligrapher will not work.
what if you tried this sequence and substituted calligrapher for the keyboard install?
http://forum.xda-developers.com/showpost.php?p=2271142&postcount=692
Phatware states calligrapher doesn't play well with third party apps that affect touch screen behavior and that is probably the problem here
not yet
^^ done without success
posted in another forum in reference to SIP troubles and Calligrapher...
"The main difference between CalliGrapher 8.6 and all previous versions is that it has been compiled with recently released Microsoft Visual Studio 2008. It is remotely possible that the new compiler has performance issues, but we have not heard anything about this and have not seen any evidence in our internal tests. The only difference that we’ve noticed when using the new development tool is that size of the compiled binary files slightly increased.
We will continue testing and will post additional information if we have any. "
Maybe trying previous version might help.
Also, taking the logic from this thread http://forum.xda-developers.com/showthread.php?t=398091 it might serve you to start from scratch and reload ROM then tackle this calligrapher issue then move on to loading other applications.
Partially success - Hard reset
I have done a hard reset.
installed first the calligrapher 8.6
soft reset
installed default_im_cab
changed sip through default_im_cab as writeanywhere
soft reset
Now writeanywhere is available and working in all applications except for Lexisgoo dictionary 3.1.1
Any help or suggesstions?
I've been trying to install the .NET framework for my Tilt, and it keeps spitting out "installation unsuccessful". It installs fine on my computer, then it goes to install it to my phone via ActiveSync (Windows Mobile Device Center actually because I use Vista). The installation screen on my Tilt pops up saying it's installing, but the bar doesn't move at all, and after a few seconds it just says it's unsuccessful without giving a reason!
I'm using the stock ATT Tilt rom, 6.1 version. I haven't done anything special to it, so I have no idea why it wouldn't work...
Can anyone spare some sage wisdom as to why this won't install? I'm trying to use wmVista and it needs 3.5 to work .
Note: I downloaded the .NET 3.5 right from Microsoft: http://www.microsoft.com/downloads/...49-3c6b-42f1-9fd9-0041345b3385&displaylang=en
Have you tried copying the NET CF3.5.cab directly to your Kaiser & then installing. The cab can be found in the installation folder on your PC or on this site if you do a search.
I've always installed from the cab file never from the PC installation so might be worth you trying it !
You might want to get the mobile version of .net 3.5...
http://frifor.com/download/IBI/NETCFv35.wm.armv4i.CAB
Download that to your memory card, then launch it with file explorer on your phone, and it should start to install all on its own. Install it to your device, not the media card, for quicker running .net 3.5, or if you want to save space install it to the media card, but it will run slower...
And FYI, the search function works very well, as well, if you had looked about 5 posts bellow this new one you created you would have seen a thread already dealing with this exact issue.
pjcforpres said:
You might want to get the mobile version of .net 3.5...
http://frifor.com/download/IBI/NETCFv35.wm.armv4i.CAB
Download that to your memory card, then launch it with file explorer on your phone, and it should start to install all on its own. Install it to your device, not the media card, for quicker running .net 3.5, or if you want to save space install it to the media card, but it will run slower...
And FYI, the search function works very well, as well, if you had looked about 5 posts bellow this new one you created you would have seen a thread already dealing with this exact issue.
Click to expand...
Click to collapse
Ah, I saw that thread before posting but I assumed by his first post that his problem was different than mine. I just check it out again and saw the direct downloads for the cab file, so I'm gonna try that out. Thank you for your help!
(I'm a new poster, but I've been lurking around these boards for a while now looking for stuff for my Tilt)
Hopefully this works...
i installed .NET CF 3.5 on my device then after installing my camera is just plain black and doesnt show any picture.
problem solved!
- i installed Resco Registry Explorer and .NET compact framework 3.5 on my Kaiser
- opened resco registry and searched for the .NET CF
- disabled .NET CF 2.0 by changing value from 1 to 0
- then enable .NET CF 3.5 by changing value from 0 to 1
I had the same problem, used your link, it worked perfectly. THANKS!!!!
Help 3.5 framework isn't working and I can't update it toboot...:-/
might have something to do with memaid as I moved a few dlls to the internal storage....but I'm not sure. Also tried uninstalling it and that seemed to fail..
Tried reinstalling and I'm getting:
Installation error. Stop all applications and processes, maximise available storage space, and run iinstallation again. Support info: 2'
I'm at my wits end as quite a few programs I liked using require this...Help please!
anyone know how i can completely remove .net framework and try again as the reinstall is failing and uninstall isnt working either perhaps ill have to do it manually?
I have *so* many programs installed that I don't want to flash a fresh ROM.....it'll take *way* too long to set my device up again. It'd take months perhaps.
pretty pretty pretty please help me :-/
Tried tweaking now can't see .net compact framework but install still fails with the same error code.
Can anyone help?.....
Please?
Deleted all reg entries at:
HK Local machine\software\microsoft\netframework...
Reinstall of 2.0 framework appeared successful....
Errors on reboot. Programs which require it crashing with:
File or assembly name
One program:
'System.Windows.Forms, Version=3.5.0.0, Culture=neutral, PublicKeyToken=969DB8053D3322AC', or one of its dependencies, was not found.'
AdvancedConfig givesthe same error (and I really need to tweak some of these settings back but it won't load!)
ShootMe! crashes simply with 'We're sorry' and I can't see the error report.....
Please someone help! I'm at my wits end. I'll try deleting the reg entries and installing .net framework 3.5 in the hope.....