I bought a new device and when I tried to upgrade it with an unofficial ROM I couldn't do the step of upgrading SPL and the indicator stayed stop at 0%
My Device boot loader shows :
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
I have tried all Hard-SPL Standard and Developers versions but I got the same result stopping at 0% including the RUU_Signed.nbh which is designed especially diamond came with 1.93 SPL originally
Please help me
fofo1881 said:
I bought a new device and when I tried to upgrade it with an unofficial ROM I couldn't do the step of upgrading SPL and the indicator stayed stop at 0%
My Device boot loader shows :
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
I have tried all Hard-SPL Standard and Developers versions but I got the same result stopping at 0% including the RUU_Signed.nbh which is designed especially diamond came with 1.93 SPL originally
Please help me
Click to expand...
Click to collapse
You have Hardspl installed already. You don't need to overwrite it again.
Kevbodian said:
You have Hardspl installed already. You don't need to overwrite it again.
Click to expand...
Click to collapse
But also when I try to upgrade directly with any cooked ROM I face the same problem
the upgrade stops on 0%
Plz help me if u have any idea
THX
What you show is the shipped SPL - so you will only be able to use offfical (if branded) operator customised ROMs.
more info to follow... (just on the phone)
There is a sticky thread about this problem
http://forum.xda-developers.com/showthread.php?t=409425
Just a tip..read that and your problem is gone
fofo1881 said:
I bought a new device and when I tried to upgrade it with an unofficial ROM I couldn't do the step of upgrading SPL and the indicator stayed stop at 0%
My Device boot loader shows :
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
I have tried all Hard-SPL Standard and Developers versions but I got the same result stopping at 0% including the RUU_Signed.nbh which is designed especially diamond came with 1.93 SPL originally
Please help me
Click to expand...
Click to collapse
If your phone shows this info after you flash hard-spl in your device, you dont have hard-spl in your device at all, so flash that first
you should seen 1.93Olinex forexample if u have flashed the 1,93unsigned hard-spl
R3PUBL1K said:
What you show is the shipped SPL - so you will only be able to use offfical (if branded) operator customised ROMs.
more info to follow... (just on the phone)
Click to expand...
Click to collapse
My device is not branded....
Do u mean that it will never accept upgrading to coocked ROMs ?
DO u think that there is no method yet ? or we will find new methods in the future ?
alas
fofo1881 said:
My device is not branded....
Do u mean that it will never accept upgrading to coocked ROMs ?
DO u think that there is no method yet ? or we will find new methods in the future ?
alas
Click to expand...
Click to collapse
No I am not saying that - If you dont have either OliNex or Jockeys HARDSPL then you could only use offical ROMs....etc etc...
So you really need to sort this issue out then you will be free to load any cooked ROM depending on your region
Remember that OliNex's SPLs have protection in them so that you can only update while you machine is connected via activesync.
When you try and Run the olinex SPL then you should get a popup on you devices screen asking you to confirm you want to run this application. Do you get this far?
Have you tried Jockys?
R3PUBL1K said:
When you try and Run the olinex SPL then you should get a popup on you devices screen asking you to confirm you want to run this application. Do you get this far?
Click to expand...
Click to collapse
I've done that but it was useless and I've got the same problem 0%
R3PUBL1K said:
Have you tried Jockys?
Click to expand...
Click to collapse
I have not heared about it also i couldn't find it in the forum
would u lead me please ?
fofo1881 said:
I've done that but it was useless and I've got the same problem 0%
I have not heared about it also i couldn't find it in the forum
would u lead me please ?
Click to expand...
Click to collapse
Try here JOCKY
omar 1958 said:
Before flashing Olinex Hardspl you need to do three things:
1. Download Net framework Compact from herehttp://www.microsoft.com/downloads/details.aspx?FamilyID=e3821449-3c6b-42f1-9fd9-0041345b3385&displaylang=en Connect device to pc and wait for Active Sync to finish. Now run the download and follow instructions, make sure to install to device and NOT to storage. Reboot your phone.
2. Download and install Cert_SPCS. (Attached).
3. Download and Install EnableRapi. (Attached). On installation of this, your phone might come with the comment that this file is already on the phone and installing this file will remove the old one, accept the new installation and reboot.
Having done the above, you are now ready to flash HardSPL. For further help read this http://forum.xda-developers.com/showthread.php?t=476738
Good Luck this time round.
Click to expand...
Click to collapse
Never had to this before - but I've never had any issues flashing Hard SPL to devices - over 50 different handsets
Hey, I gotta apologize for my above post. I read the 1.93.000 as 1.93.Olinex.
R3PUBL1K said:
Remember that OliNex's SPLs have protection in them so that you can only update while you machine is connected via activesync.
Click to expand...
Click to collapse
What do you meen? I have olinex1.93 and never use Active sync to flash a rom (or start AC), I put my phone in bootloader manualy and flash. Or is Ac startup even is this situation?
omaga said:
What do you meen? I have olinex1.93 and never use Active sync to flash a rom (or start AC), I put my phone in bootloader manualy and flash. Or is Ac startup even is this situation?
Click to expand...
Click to collapse
I was trying to explain that don't try flash (another) SPL using HardSPL as olinex one has overwrite protection.
Flashing ROMs this way is no problem - but not recommended
Upgrading is not possible
R3PUBL1K said:
I was trying to explain that don't try flash (another) SPL using HardSPL as olinex one has overwrite protection.
Flashing ROMs this way is no problem - but not recommended
Click to expand...
Click to collapse
I found that this new version of devices is HardCoded with original HTC-SPL
So its seems that upgrading to unofficial ROMs is not possible yet ...
thank u all for your concern
R3PUBL1K said:
I was trying to explain that don't try flash (another) SPL using HardSPL as olinex one has overwrite protection.
Flashing ROMs this way is no problem - but not recommended
Click to expand...
Click to collapse
I have Olinex 1.30 and have previously upgraded from ROM 1.34 to 1.93. However, I have tried upgrading the ROM to 2.03.831 but it doesn't work.
Do I need to upgrade the Hard SPL to 1.93 signed? Where can i get the file?
Thanks.
Hello,
try the "RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip" from THIS thread as this was the only one that worked for me. I recently flashed a O2 branded Diamond and was also about to give up...it was my last try/chance and eventually I succseeded in flashing any Diamond ROM until 100%.
...bye DonQ
does it means I have to overwrite my HardSPL 1.30 signed?
Got a new Diamond and same issue, can not hardSPL1.93 Olinex over this new original SPL 1.93.000
Hey I succeeded to work this out!!
Here's what I did:
Download this file: Unsigned-Hard-SPL-Diamond-OliNex.zip
and this: RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip (you can choose another developer version such as HardSPL_Olinex137_Unsigned.zip)
Now copy the file RUU_Signed.nbh of seconde archive to replace the one in the first archive. Then run the ROMUpdateUtility.exe of the 1st archive. As the moment the percentage bar appears, run the SSPL-Manual.exe of the 1st archive from your PDA (of course, this file must be copied to PDA before via ActiveSync).
Just run again ROMUpdateUtility.exe if you have a phone not responding error.
Then there you go...
4fun00 said:
Hey I succeeded to work this out!!
Here's what I did:
Download this file: Unsigned-Hard-SPL-Diamond-OliNex.zip
and this: RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip (you can choose another developer version such as HardSPL_Olinex137_Unsigned.zip)
Now copy the file RUU_Signed.nbh of seconde archive to replace the one in the first archive. Then run the ROMUpdateUtility.exe of the 1st archive. As the moment the percentage bar appears, run the SSPL-Manual.exe of the 1st archive from your PDA (of course, this file must be copied to PDA before via ActiveSync).
Just run again ROMUpdateUtility.exe if you have a phone not responding error.
Then there you go...
Click to expand...
Click to collapse
Ok now, I got the same situation as described above, but the phone's software won't boot. I can just put it in the bootloader mode. I cannot put the SSPL Manual file on the device. How do I reflash it then? USPL said that this version is not supported. Any ideas? Thanks for any input.
Related
So, guys, here is the first test SSPL for breeze. I have no breeze, so please report if it works.
extract to your device root!!!
start spl.lnk AND immediately press POWER and CAMERA buttons. (or try hust CAMERA)
if the screen shows sth like spl 1.01 DFR, then everything is ok - it is my spl
this version was intended to allow you to flash any CID rom update and unsigned nbh files. the next release will be based on the latest spl and include compatibility with new RUU of 1.34 rom updates and the feature to fix bad blocks.
EDIT - may 10, 2007 - SSPL V1 works successfully
CID check - disabled
NBH check - disabled
attached spl in nbh format for flashing - breeimg.zip
Thanks to:
DES for his SSPL
Olipro for his hard spl which actually saved me from hours of IDA analysing - I simply compared his spl to original and patched the one from breeze
at first try...
i have exactly what i descriped here:
http://forum.xda-developers.com/showpost.php?p=1253965&postcount=782
after the reboot i can't get into the bootloader...
what did you changed in the spl ?! or in the sspl.exe ??
I try... It's WORK!!!!!
what did you do??
edit:
ok, strange things goes on here ... just tryied it another time yet...
ipl-sspl by Des
SPL-1.01
should work
if i have time today i will try to made an cooked rom ...
if this works i look for a way to extract the files out of the excalibur wm6 rom ...
edit2:
i now have the problem that i can't connect mtty to bootloader... mtty ends with error when producing the cmd command line... i just had this problem with hermes to... i have 2 mtty version on all the 2 the same error...
i will try it now on a other machine..
1) Rename the BREEZE_HTCEUR_1.34.251.1_SHIP.nbh file to BREEIMG.nbh
2) Copy to sd card
3) start spl.lnk and immediately press POWER and CAMERA buttons
4) Phohe start in bootloader and flash new rom. (but no new radio)
THX
Thx for the replies, i`ll try to make a newer sspl. also, let`s begin the work for wm6 for breeze based on hermes rom... but in another thread some time later
can anyone confirm that they have sucessfully flashed a cooked ROM onto a breeze? Please update the wiki.
doedoe said:
can anyone confirm that they have sucessfully flashed a cooked ROM onto a breeze? Please update the wiki.
Click to expand...
Click to collapse
Hi, i work on it!!
on afternoon/evening i will try to cook a rom with a few freeware tools bases on the actuell rom!!
i can begin working on wm6 rom recently when extract the excalibur content... because of the problem that breeze is a smartphone an hermes a ppc there would be some problems with coredll's of the system! because of that i need smartphone wm6 rom... befor that there is no wm6 on breeze possible!
....
can anyone else can try mtty with the sspl ?
-----
engel98 said:
1) Rename the BREEZE_HTCEUR_1.34.251.1_SHIP.nbh file to BREEIMG.nbh
2) Copy to sd card
3) start spl.lnk and immediately press POWER and CAMERA buttons
4) Phohe start in bootloader and flash new rom. (but no new radio)
Click to expand...
Click to collapse
this should work when you have a new spl installed - and you want to flash another cid rom!!
has nothing to do with unsigned code!!
!!! only for understanding!!
hey what should i say...
it just look like that it works...
i have cooked a rom now...
only small reg changes!!
i have flashed it with hermes RUUUpdaterV2
only a OS file!
Phone boots! now i have to check if the changes are taken over!!
But why not ;Þ
Please post to the wiki.
I am hoping that we can use tornado WM6 code to cook a WM6 image...
I just added some Infos to wiki!!
Updated:
Breeze/MTeoR Upgrading Guide (4Hard/S-SPL)
Custom RUU Updater
I can also confirm that this SSPL truly works, but I am still unable to flash 1.38 radio over 1.29 currently installed with this SSPL version.
Any hints when could we expect SSPL based on some newer SPL release (like 1.09 or 1.10)?
just extract the radio rom what you want from an shipped rom ...
take it and re nbh's it with the nbgehn utility ... than put it in the custom ruu folder start ruuwrapper and flash it...
futureshock said:
just extract the radio rom what you want from an shipped rom ...
take it and re nbh's it with the nbgehn utility ... than put it in the custom ruu folder start ruuwrapper and flash it...
Click to expand...
Click to collapse
Tried that 3 times already. Doesn't work! Although process finishes whithout any glitches, System Info still says Radio ROM 1.29.00, and my phone still acts like crap...
.... i tried it too ... no problem... you should have done a mistake...
download an usb sniffer and let it run when updating... maybe then we can see the error...
but i had done it too... with sspl had no problems!!
I confirm this is also work on my dopod 595.
Now I need to search how to change the splash screen
what would you want to change??
futureshock said:
.... i tried it too ... no problem... you should have done a mistake...
download an usb sniffer and let it run when updating... maybe then we can see the error...
but i had done it too... with sspl had no problems!!
Click to expand...
Click to collapse
This is what I did/have...
- I have installed Radio ROM 1.29.00.10 (with older 1.32.251.1 RUU)
- My MTeoR is CIDed QTEK_A07 - all available RUUs fail with INVALID VENDOR ID error
- If I use SSPL (linked in this thread), my MTeoR actually does start SuperCIDed and I can run any RUU or custom ROM, and although all of them complete with success Radio ROM DOES NOT CHANGE at all.
My theory is (based on posts in Hermes upgrading forum) that Radio ROM 1.29 installed Radio BL 0108 which in turn does not allow flashing Radio ROM when started SPL is pre-1.09 codebase. I presume that it flashes with 1.09, 1.10 or newer only (makes sense because HTC released new 1.34 RUU which first installs SPL 1.09, then the rest of ROM).
Can anyone concur with my assessment or am I completely wrong?
Ohhh,thank.It works perfectly on my HTC MTEOR from O2 Czech Republic.
sp3dev said:
So, guys, here is the first test SSPL for breeze. I have no breeze, so please report if it works.
SSPL V1 works successfully
CID check - disabled
NBH check - disabled
Click to expand...
Click to collapse
WOW
I have now read for weeks the Hermes/Trinity threads wondering if this would be possible for "simple" smartphones too - and you did it
So while it is possible for the MTeor, maybe your kind of patching the SPL would also work for the Excalibur/S620?
I would love to flash my O2 Cosmo, but want to have an original ROM Backup for warranty/fallback reasons.
I also found out that it is possible to extract and cook ROMs for it like the way for the Hermes - but I cannot flash because of this f****g need for signed .nbh.
May be you are able to do this MAGIC on a Excalibur SPL too?
I would try out on my phone if you want to take the challange - if it doesn't work I think I'll have to get a MTeor
Anyway - lots of thanks for your work - and giving me back my hope on smartphone ROMcooking
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
If i were you I'd use this one =)
futureshock said:
ok i found it i didn't read further the 1st page on sspl thread
edit:
have repacked it with runme.bat and 77.7er SSPL ...
Radinly_1.54.30.10
Click to expand...
Click to collapse
At least I did and it worked =)
and then I'll highly recommend this WIM6.1 release by FutureShock: http://forum.xda-developers.com/showthread.php?p=2094056#post2094056
GL =)
I've GOT IT!!! using various mix and match method, im flashing the phone now!!! fingers crossed it'll boot later
UPDATE: DOESNT WORK! PLEASE HELP
It sure will.. Even I got it to work really fine
crap!. doesnt work. it's still SPL 1.09 and stuck at 2nd boot screen.
is there a ROM editor that works for meteor? can someone please suggest one that can be used to sign the nbh file.
jerpelea, or futureshock, please help
not good news
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
PiGeonCZ said:
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
Click to expand...
Click to collapse
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
alexnvidia said:
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
Click to expand...
Click to collapse
why did you format ?
try to reflash 1.09 spl
and after this wwe one of 1.34 roms to get 1.10 spl
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
Click to expand...
Click to collapse
jerpelea: First of all I will say thank you for taking all that time you do spend on the ROM cooking/building/making/what-ever-is-the-right-name and I/we really appreciate it!
jerpelea said:
but i dont know if you have the knowledge
Click to expand...
Click to collapse
I think that comment was really unnecessary!
As a n00b I know how hard it is to understand what’s happening. I did read the wiki’s and still I didn’t get HOW TO upgrade a ROM until I found a great post in FutureShock’s thread
darkDirk said:
First of all:
It's fantastic what you are doing with wm6.1 and the Breeze, Futureshock !
I am new and trying to upgrade it myself, but at first I didn't have any luck.
Here is a simple newby step-by-step manual:
- Download and extract a MTeoR-FutureShock-WM61-xxxx.x.rar
- Check your Mteor battery in more then 50 % full
- connect the Mteor to the computer via usb and check if Activesync works
- go with DOS (cmd line) to the directory and start runme.bat
- On the Mteor press camera and powerbutton at the same time.
- then immediately press any key on the computer to continue the batch script.
- now you should see the 3-color bootscreen
- press any key to start the rom-update program and follow its directions.
When the update is finished (in less then 5 minutes), then wait untill the first boot is complete.
If you don't get the 3-color bootscreen or you the update on the Mteor stays on 0 % and the rom-updater displays an error, try testing this:
On the Mteor start the explorer and in the root directory (press UP once) find SSPL.EXE en start it.
If the Mteor won't start the program and there is an error like "insufficient trustlevel".
You need to remove the application lock on your Mteor.
Run SDA_ApplicationUnlock.exe on your PC with Activesync working and then install SP_AllowCertificateInstall.cab on the Mteor.
You will find those two in the .rar in ".\opt Software\Unlock Tools"
Then redo from the start.
Then, Have fun !! (Futureshock & DarkDirk)
P.S. works on a BREE100 with IPL-0.90 and SPL-2.05.
Click to expand...
Click to collapse
But I still do not know what SSPL, SPL, IPL or whatever there is does to me or/and the phone.
Anyway. Thanks for all the work.
if someone has a corrupt CID just send me an pm...
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
with all the respect what you do for this community, isn't taht you who advice us to update the SPL before trying your images?
in this thread http://forum.xda-developers.com/showthread.php?t=384398 you should probably higlight that the update should be done only on WWE devices.
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
alexnvidia said:
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
Click to expand...
Click to collapse
run terratem
type info2
if it sais A07 then just flash rusian 1.34 rom and enerithing will be fine
application unlock it
run sspl 77.7
flash wm6.1
if it says enithing else you need to locate your original rom
till now i found that it sais a07 in most cases
BR
alexnvidia said:
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
Click to expand...
Click to collapse
it depends on the info displayed on terraterm
for A07 you can use the russian rom to recover
this is what i got from terraterm. same as mtty.
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
i did flashed back to my original ROM after the first stuck in WM screen incident. and amazingly the flashing process works after several mix and match. after the original (WM5) ROM completed flashing, my IPL is downgraded back to 0.9 and SPL is still 1.09, and im still stuck at the WM logo screen (this time WM5 logo).
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
futureshock said:
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
Click to expand...
Click to collapse
i tried SD card flashing too yesterday. it says not allowed. i have already flashed over the original dopod 595 ROM and my phone is now WM5. the flashing is 100% successful, but it is still stuck at the second boot WM screen.
i think im in a really screw up position now. i have SPL 1.09 and IPL 0.9. i dont know what is corrupted now. is it the CID? SPL?
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
futureshock said:
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
Click to expand...
Click to collapse
both mtty and terraterm give me the same msg when i type info 2. it says time out (refer above for exact error message).
the original dopod 595 rom has SPL2.05. and it was successfully flashed into the phone. when the phone reboots, it is still stuck at 2nd boot screen (WM logo). i checked, the SPL is still 1.09, but IPL has been downgraded to 0.9.
Hi, i've bough a p3600 on ebay.
The seller tell me the phone is out because he flash a bad radio version on the phone.
I try to upgrade some file. ( Rom OS, Radio, SPL,etc ...)
I try the splexploit...
BUT ... The phone already stay on startup. i can see HTC startup screen,the windows startup screen ...but never the today screen.
I try hard reset, htc official rom, cookeed rom,...but when i flash a rom with "gsm", the update freeze at 13%
I try with usb and with sdcard..same thing, already stay at 13% !
But if i flash hard spl, 100%, if i flash OS, 100%, just the radio freeze at 13%
Any idea please ?
update
after the boot, i've got a "no gsm" message near the radio version
other people got the same problem like me ...
God oli, help me please
I more or less had the same thing and solved it with the sc card flash page.
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
A rom that works for me to flash it back to the working original
http://www.allaboutphones.nl/forum/request-originele-spv-m700-rom-p3600-rom-t727.html
To download you have to register with them.
GL
Hi, updating the radio to 1.56 crashed, now I have the No gsm message and doesn't boot, running mtty from bootloader with info2 command it says supercid but I can't update any official rom SPA, WWE, ITA... the error is "vender id invalid". I've tried the sd method but returns to bootloader .
Any help will be appreciated.
You should try SSPL : http://forum.xda-developers.com/showthread.php?t=293632
And if it doesn't work the Des' Crash-Proof SPL :
http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66
and try to flash a radio rom again !
doesn't work
try again and again ...the phone block at 13% ( when the radio upgrade begin) ...
pfffff
I've the same problem and after several attempts without result I sent the phone to the workshop and they told me the problem is with the main board! (this cost almost the price of phone itself). Moreover, I've seen some where here that the problem could be caused by radio chip but I couldnt get the detail.
If you find a solution give me a tip.
i've test lot of thing.
I progress with mtty. but i've got a problem ..i can't downgrade the phone under SPL 1.05.
SPL 1.04 can "reset" the radio, or enter directly to the radio bootloader. With that, i can save my phone.
Try mmty (see the wiki => bootloader info) and with the mfg spl, you can try the method.
Guys,
I've got the same problem...
I've sim and cid unlocked my spv m700 some time ago, using wonderful software from pof. Everything went smooth.
Today I've decided to update radio rom to 1.38.00.11 to enable gps.
I've launched RUU, everything was ok till 44%, when I've got message "Communication error".
After that program tried to recover rom without success, I've got another message "Image corrupted"...
I've tried to reboot my spv (both SR and HR), after rebooting I see:
M 05
B 05 D 1.23
then those symbols disappear and I see only Orange logo.
That's it... The end...
Should I reload radio rom or both rom and radio rom to my DEAD spv? If yes - how?
Please help as I'm very disappointed, frustrated and so on!
Thank you!
Update: A-A-A!!! I did it! I revived my spv! Let me explain how (I'm kinda new to all this rom and and ssl things, so forgive me for mistakes, if there are any):
1 I ran unbrick software. Yesterday it did not work (said, that could not find smth), but today it worked fine.
2 I ran RUU and BINGO! That's it!
BTW, I have vista, but it still worked (I think, thanks to Windows Mobile Device Center, which I have installed).
Also, I killed wmd process in Task manager in the beginning (have read this recommendation somewhere).
Thanks to everybody for their help!
nyco,
could you please explain briefly what you did exactly and which radio and rom you used
thanks and regards
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Thanks stepw...
when I hit task 2A nothing happens.
Original ROM doesnt respond. I flash with cooked ones. Result 100% successful. I restart the phone- hang at boot screen.
stepw said:
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Click to expand...
Click to collapse
Hi,
I'm already under the hard SPL. and "task 2A" not working.
Macars, try only with radio ripped or full original rom (from htc or cooked with radio) because some cooked rom have only OS.
Can you tell me what SPL you have?
Hard SPL?
Have you try splxploit ?
Can you tell me what rom you try oviplokos1 ?
thanks,
it shows SPL 9.99 and with this I cannot flash anything so what I do is to update with splxploit and then the phone changes to SPL 1.2 olipro. With 1.2 I can only flash coocked ROM and will go until the end 100% successful- (original ROM the phone does not respond), but when restarts with newly loaded cooked ROM the phone hangs at window login screen and when put it in bootloader the SPL 9.99 returns again.... the story goes on like this.
I'm becoming mad....
hi,
you can only flash cooked rom because the rom you flash contains only OS. When you flash HTC rom, the rom contains os+radio+spl+....other thing ...
Try this method to downgrade your SPL (9.99) to oli 3.20 :
1°) run splxploit
2°)when the phone reboot on the spl 1.20 oli, run HardSPL 3.20 olipro. (search on the wiki or the trinity forum
3°)upgrade to 3.20 oli ...
Now, when you go to the bootloader, you can see SPL 3.20 oli.
Try reflashing a radio only (see the upgrading topic, you will see radio 1.56.xxxx)
Tell me if this method work.
When i'm on spl 3.20 oli, i can load radio rom to 0%
when I downgrade my phone to spl 1.05, and i can run the upgrading to 7% (best score )
To downgrade to SPL 1.05:
edit the "unbrick.bat" on the splxploit folder.
Replace TRIN_HardSPL.nb to TRIN_SPL105.nb
try to find SPL 1.04. I'm sure if i got the spl 1.04 i can revive the phone
Did exactly as you said final result:
When i'm on spl 3.20 oli, i can load radio rom to 0% (and stays there )
hi,
ok, try to load spl 1.05 with splxploit, and when it is load, run radio upgrade (1.56.xxxx)
Try to find spl 1.04 and mtty it can be reset the radio bootloader
if you find 1.04, give me it
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
macars said:
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
Click to expand...
Click to collapse
arf :/
You got exactly the same problem i have.
did you check if you have bad block (with mtty)
try format the phone with mtty.
i contact pof, but he doesn't answer me
yes, the xperia seems to have a normal HTC SPL... so it will probably need a hardspl. =)
[size=+2]UPDATE: RELEASE TIME[/size]
[size=+2]NOTE: This is NOT a SIM unlocker - it also doesn't unlock Security for other radios. if you need that, GO HERE[/size]
UPDATE - NEW: 0.78.OliNex Hard-SPL, I was asked to help with this as 0.78 seems to work better for some newer devices. it's the attachment xperia078_2.zip - to flash this over your existing Hard-SPL, you can just use customruu or SD flash. you can also flash it via SSPL (such as Xperia-SSPL-Manual EXE) or if you overwrite NBH file in X1_HardSPL_v1 after running the exe.
thanks for any donations, you can see the donation link in our signature - the big link saying "elite project".
Instructions to flash Hard-SPL:
it's recommended you run the basic package, and don't flash the other attachment (MFG SPL - it is only for hackers).
0a) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/...fd-ae52-4e35-b531-508d977d32a6&DisplayLang=en
0b) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center.mspx
1) download Hard-SPL package from attachment, extract to an empty folder.
2) it is recommended you download only the X1_HardSPL_v1.zip unless you want to tinker with MFG SPL (MFG SPL 0.52 is a separate attachment).
3) you must Have Phone Synced with PC in Windows Mobile!
4) run X1_HardSPL.exe. (if you want to flash MFG SPL: at this point replace the extracted RUU_Signed.nbh with the MFG version of RUU_Signed.nbh)
5) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
6) it should go to tricolour screen now and say 0.52.OliNex.MFG (this is SSPL!).
7) Hard-SPL flashes, device automatically reboots, job done.
8 ) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.72.OliNex (or 0.52.OliNex MFG).
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned OFF, press and hold the volume down button along with the power button, then release the power button, and finally release volume down button when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically(your device doesn't go to tricolour screen), please copy Xperia-SSPL-Manual.exe from the Xperia-SSPL-Manual.zip attachment to the device and run it. then once the screen is in SSPL (tricolour screen saying 0.52.OliNex), run RUU on the PC (i.e. the rest of the hardspl package) manually.
NOTE 3: this is unsigned Hard-SPL. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here - scroll down!
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL. use Xperia CustomRUU to flash other ROM images. for example this version: http://rapidshare.com/files/164933503/X1_CustomRUU.zip
***
IMPORTANT: extra Xperia-specific notes: the prerelease roms out there in the X1 ROMs thread are not going to flash on retail devices because the radios they include are only flashable on prerelease devices ("Security unlocked" message in SPL can be seen on these). so what you need to do is repack the NBH without the radio - this will only work with Hard-SPL though, as repacking breaks the HTC sign on the NBH file.
I had a tester upload a repackaged UK image, which will flash fine. you can find it in the x1 roms thread. =)
***
TROUBLESHOOTING TIPS:
- read the instructions.
- read the instructions.
- read the instructions.
- if you get connection error in RUU after the device goes to tricolour screen, then try a different USB port, also do not use USB hub, you can also try rebooting your PC, and can try using another PC. read the thread for even more tips that I don't remember now. also you can try unticking advanced network functionality in start menu / settings / connections / usbtopc applet.
- if hardspl EXE won't run, and you are on vista, try to right click it and use "run as Administrator" option
- if SSPL-Manual.exe or enterbootloader.exe fails to run (says missing component or similar), try a hard reset of the device.
***
extra how to: how to restore Stock SPL for warranty reasons.
step by step:
- this is ONLY for warranty reasons. i.e. the device needs repair and you have to send it to htc to get it serviced. if you plan to restore hardspl then don't even bother flashing this stock package, unless you are some kind of hacker/dev
- IMPORTANT: be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
- now the steps
1. download the stock spl package from this post.
2. download X1_HardSPL_v1 too, from this post.
3. run the hardspl package, but do not press Next button i.e do not go ahead with flash yet.
4. at this point, take the extracted stock SPL, a RUU_Signed.NBH file, and overwrite the other RUU_Signed.NBH in hardspl package.
5. go on with the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to tricolour screen with 0.52.OliNex version), it goes to 100%, reboots, done.
+1. to verify, enter bootloader (see description above in this post), and check version number on tricolour screen. it should say 0.72.0000.
OliNex said:
yes, the xperia seems to have a normal HTC SPL... so it will probably need a hardspl.
so, let us know if you have a prerelease device to test on... we looked in this forum and saw several people who have one. thanks.
Click to expand...
Click to collapse
I just got my xperia and i'll be willing to use my x1 to test hardspl. Its a retail version and not a prerelease x1 if thats any help.
I have, and have already dumped all rom to raw. You can pm me what you need or catch me on msn.
I can do my best to help.
What is a SPL ?
Does anyone have a working version of the hardspl for the X1 so we can try it? Thanks
Yeah we need SPL big time, any genius working on it?
I said that Olipro and cmonex will make Xperia Hard-SPL. So people, it's time for test :d
And the most important don't forget to say "thanks" and click on donate link
borce_razor said:
I said that Olipro and cmonex will make Xperia Hard-SPL. So people, it's time for test :d
And the most important don't forget to say "thanks" and click on donate link
Click to expand...
Click to collapse
THANX
but I dont see the test download
I sent them a msg a while back (weeks maybe) saying i had a proto x1 and was willing to sacrifice it for the cause. Still am - Nothing back though.
I for one will donate for the cause need a generic uk rom without the crap bluetooth problem
the_flyer said:
I for one will donate for the cause need a generic uk rom without the crap bluetooth problem
Click to expand...
Click to collapse
i've got a generic uk xperia but still have the dreaded bluetooth problem
damn. I have had more luck today with the bluetooth and touch wood havent had any problems since the wifi was switched off...
Have you tryed switching off standby mode? It sorted the bluetooth prob out for me, untill i installed afew new apps. Problem back again
[size=+2]UPDATE[/size]
we will start work today (we = OliNex = Olipro & cmonex)
I'll check the PM's soon, as we need testers.
as for donations: yes we would appreciate them much, would help a lot (the big link in first post, don't worry about it saying diamond/raphael)
P.S.: bluetooth etc offtopic problems should be posted elsewhere, please. thanks
Xleecher said:
I just got my xperia and i'll be willing to use my x1 to test hardspl. Its a retail version and not a prerelease x1 if thats any help.
Click to expand...
Click to collapse
retail version is better! PM me with your MSN contact address
@ Cmonex
I've got X1i (vodafone) retail as well and willing to help in beta testing too.
Also donated £10.00
hassan said:
@ Cmonex
I've got X1i (vodafone) retail as well and willing to help in beta testing too.
Also donated £10.00
Click to expand...
Click to collapse
thanks have you got MSN ?
cmonex said:
thanks have you got MSN ?
Click to expand...
Click to collapse
Yes just click that small icon under uk flag in the right corner.
Donated £10. Thanks for your help with the hardspl guys.
Hi all, I've created HTC Jade CustomRUU patched to perform a 'task 32' instead of a 'task 28' after flashing an .nbh, so it will not format your device if you just flash a radio or a splash screen.
How to: Drop the .nbh file of your choice in the same folder as CustomRUU and start flashing.
Everyone NOTE:
AVG and other anitvirus's usually detect a virus in CustomRUU.exe, it's false error. Disable your antivirus while downloading and flashing.
Have fun.
@udK
should I understand that radio is possible to flash in? Pls to provide me a link with the radio topic.
thnx much
How's about the change and I know how to install because of I just buy it?
I don't know every things.
Why I can't to uprom from it? It show file can't open between uprom.
Hi and thanks for your great work.
What I would like to know, is if I can use this with my HTC Touch3G please? I know it is code named the HTC Jade, but is that what yr RUU is for?
If I can, do you know where the latest Touch3G roms can be found?
aussie
aussie_boi said:
Hi and thanks for your great work.
What I would like to know, is if I can use this with my HTC Touch3G please? I know it is code named the HTC Jade, but is that what yr RUU is for?
If I can, do you know where the latest Touch3G roms can be found?
aussie
Click to expand...
Click to collapse
Yes it will, but you can only flash stuff if you have HardSPL installed.
So until it's released this app isn't much use to you
"What is is used for...?" It flashes the image from your PC to your device. There is a RUU with all ROM updates (including the carrier ones), this is is patched to stop you wiping your data if you are just flashing a Splash screen or Radio.
Dave
Big Thank you Dave. I will be patient then and say a few prayers
aussie
re
can i flash rus rom whis this tools?
(have eng firmware on device)
streech said:
can i flash rus rom whis this tools?
(have eng firmware on device)
Click to expand...
Click to collapse
No, you have to have Hard SPL first.
Ta
Dave
Singapore machine
Just have a question....actually how to flash singapore machine?
waiwai888 said:
Just have a question....actually how to flash singapore machine?
Click to expand...
Click to collapse
Put Hard SPL on the phone (see the stickies), then download a ROM and flash the by running the RUU executable (it should be included with the ROM - or download and use this one).
Ta
Dave
Hi
I have installed HardSPL (and confirmed) and downloaded the Radio ROM http://forum.xda-developers.com/showthread.php?t=496737
When I run the CustomRUU.exe my device resets to boot mode with rainbow screen, changes to the grey screen with progress bar and USB at bottom, but then after short while it fails with connection error. Have tried on 3 different desktops with Vista/XP but same problem.
I have downloaded the CustomRUU.exe from here and tried, but same result.
Any ideas?
Just a quick one... Is this CustomRUU exactly the same as the one included in the Jade Kitchen?
If so, then I just drop the .NBH file (radio or splash screen) in the same folder and run CustomRUU, right?
TIA!
izzyzc said:
Just a quick one... Is this CustomRUU exactly the same as the one included in the Jade Kitchen?
If so, then I just drop the .NBH file (radio or splash screen) in the same folder and run CustomRUU, right?
TIA!
Click to expand...
Click to collapse
Yep
Ta
Dave
After installing HardSPL v41 and dropping the .nbh file into the same folder as CustomRUU, the device reboots and shows tricolor
My Jade boot into tricolor screen that says
Jade100 64M
SPL-1.40.0000
MicroP-Jade (LED) v5
but get stuck in the a grey screen at 0%
why does it get stuck 0% in the flashing screen?
Curtom RUU
FYI, I found a trojan on this file...
debrahimi said:
FYI, I found a trojan on this file...
Click to expand...
Click to collapse
It will be a false positive. Many of the RUU programs have the same problems - I have written two wrappers now for the Blackstone and Topaz to remove the AV warnings. I'll see if I can knock together a Jade one.
Dave
i wonder why I cant flash customRUU on my jade
Alphas said:
i wonder why I cant flash customRUU on my jade
Click to expand...
Click to collapse
Do you have Hard SPL??
yes of course, no matter how hard i tried, hardSPL doesnt get installed in the jade.
"...for non comercial purpose, please discuss with oli blah blah blah.." Why would I wanna discuss with him for something that doesnt flash my bootloader?