Related
Hi there Android people.
I am having some issues with running the current Cyanogen *4.2.11.1*.
Phone: G1 Drea100 PVT 32B with stock 1GB SD
using anmon RA 1.5.2 recovery image
-wipe all available in menu.
-created a new partition- FAT32, Ext1 (upgraded to 4), Swap 32MB
-wiped all again.
-repair SD: ext
-flash signed-dream-devphone-userbug-ota-14721
-Once the flash above completed I did not restart, I simply flashed to update-cm-4.2.11.1
-reboot
Once it boots, my home process stops responding if I touch anything. This last for about 15 seconds, after that it seems to responds fine, but the browser and market place seems to auto-close on me from time to time, and I get random phone reboots, after a few reboots my phone simply stops turning on. I have to wait about 10 minutes to get into recovery and try to flash all over again.
I tried fix_permissions in the terminal, no luck.
I did some reading and noticed a lot of people are running different Radio/SPL versions other than stock, I am no super user, so I don't know if any of this effects ROMs, or if I should be flashing either for any sort of benefits I am missing out on? could this be the issue? Current SPL/Radio below:
HSPL10.95.3000
CDLP-4
Radio-2.22.19.261
Any input would be much appreciated.
Thanks,
D3AD PIX3L said:
Hi there Android people.
I am having some issues with running the current Cyanogen *4.2.11.1*.
Phone: G1 Drea100 PVT 32B with stock 1GB SD
using anmon RA 1.5.2 recovery image
-wipe all available in menu.
-created a new partition- FAT32, Ext1 (upgraded to 4), Swap 32MB
-wiped all again.
-repair SD: ext
-flash signed-dream-devphone-userbug-ota-14721
-Once the flash above completed I did not restart, I simply flashed to update-cm-4.2.11.1
-reboot
Once it boots, my home process stops responding if I touch anything. This last for about 15 seconds, after that it seems to responds fine, but the browser and market place seems to auto-close on me from time to time, and I get random phone reboots, after a few reboots my phone simply stops turning on. I have to wait about 10 minutes to get into recovery and try to flash all over again.
I tried fix_permissions in the terminal, no luck.
I did some reading and noticed a lot of people are running different Radio/SPL versions other than stock, I am no super user, so I don't know if any of this effects ROMs, or if I should be flashing either for any sort of benefits I am missing out on? could this be the issue? Current SPL/Radio below:
HSPL10.95.3000
CDLP-4
Radio-2.22.19.261
Any input would be much appreciated.
Thanks,
Click to expand...
Click to collapse
Why did you use "signed-dream-devphone-userbug-ota-14721"
I'm no pro but I used the base image that cyanogen recommends on his wiki page. The DRC83 defanged located here:
http://wiki.cyanogenmod.com/index.php/Latest_version#Defanged_DRC83
staunty said:
Why did you use "signed-dream-devphone-userbug-ota-14721"
I'm no pro but I used the base image that cyanogen recommends on his wiki page. The DRC83 defanged located here:
http://wiki.cyanogenmod.com/index.php/Latest_version#Defanged_DRC83
Click to expand...
Click to collapse
He used that because it is the proper image to use. A defanged file simply means that it has been rendered safe to download with no fear of infection. The link on his site is to the file used by the OP, so no worries there. Also, your radio is good, so do not worry about that either.
I have to ask, because you did not mention part of the process that should be happening. You flash the HTC image, then you do not reboot and flash the CyanogenROM. At this point you reboot. What happens? It should flash the radio, go to an HTC screen, stay for awhile, then reboot itself back to recovery where it gives a message regarding the cache being cleared. At this point you reboot for the actual boot process. Is this not happening for you?
cloverdale said:
He used that because it is the proper image to use. A defanged file simply means that it has been rendered safe to download with no fear of infection. The link on his site is to the file used by the OP, so no worries there. Also, your radio is good, so do not worry about that either.
I have to ask, because you did not mention part of the process that should be happening. You flash the HTC image, then you do not reboot and flash the CyanogenROM. At this point you reboot. What happens? It should flash the radio, go to an HTC screen, stay for awhile, then reboot itself back to recovery where it gives a message regarding the cache being cleared. At this point you reboot for the actual boot process. Is this not happening for you?
Click to expand...
Click to collapse
You are correct- after flashing CM the phone will flash the radio and reboot to the recovery screen where I will reboot again. Sorry for not including that detail.
Home process hanging in the beginning is not a problem, most people have that happenning. Eventhough home screen is shown, Android is still booting up, you just have to wait a little bit for everything to finish up.
Problems with stock apps usually indicate that something went wrong with instalation of the rom (i.e HTC 1.6 rom was not installed properly) so you may want to re-flash that again followed by CM rom of your choice.
Next time you phone reboots itself, try to get a log (there's more on how to do it in Cyan's thread), it's the only way to find out what happens.
Last, but not least, stock 1GB card is not advised for swap/apps2sd because if it's slow speed (it's class 2). Get one that's faster (class 6 preffered) and try that out, it may be the source of your problems after all.
Good luck.
how do i install this Cyanogen on my G1 with 1.6 firmware ?
simple007 said:
how do i install this Cyanogen on my G1 with 1.6 firmware ?
Click to expand...
Click to collapse
http://tinyurl.com/yjuy6u3
But in all seriousness
http://wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_G1/Dream_Firmware_to_CyanogenMod
This would work. Please use search, this is such a n00b question.
Did another fresh install, so far no issues.
I will get a log the next time I install to see if I can track down the issue.
Also had time to install Enoch 4.2.11.2 theme. <3 this theme.
I will be heading to Frys today to pick up some cooling fans for the old PC, I will take a look for new mini SD
thank you to everyone that responded.
Just got home from Frys Electronics.
Purchases an A-DATA 8GB Class 6 microSD.
wiping/flashing again.
I am having a hard time learning about the swap file part of all this... I can find guides on how to create a Swap Partition, but not sure how to make it work and/or optimize it.
So I created a 32MB Swap- Previously I read the commands to enable Swap through the terminal- "linux_swap_en=1" I have used this and it does indeed turn on swap, but is there some sort of command to optimize? I believe tweaking the swap files is adjusting the "swappiness"?
The other way I enabled the Swap file was from the spare parts menu- Enabling Compache enabled my Swap file. Does this need adjustment? for size? or any other parameters? Or is this kind of an auto on for Swap?
Sorry I am a total noob, and want to know if I am missing out, I just keep loving this phone more and more.
I will be buying Cyanogen some beer soon ^_^
I've played with swap a long time ago and never quite understood it neither. As of lately, I've been running 10mb hack (in the developement section) and it works great. If you're inclined to get the swap thing going I suggest you read this thread. This will give you an idea of how to enable and tweak swap-related tasks.
Glad to hear that you have original problems taken care of (so far at least).
Good luck.
I think I just may have bricked my phone...
I did all the steps stated in my first post while flashing to 4.2.12.2 and got things going great. Flashed Enoch's Theme 4.2.12.2. Everything was rocking.
Then today, it shut it self off, I rebooted. Got to Enoch load screen then shut off, tried it again, and it won't even get past the G1 splash screen. I have had this happen a few times before, where it would power off randomly and I had to pull the battery, wait like 5 minutes and then get into recovery and clear/flash again. Now I am getting into recovery but after a minute or so it just shuts itself off again.
Can't wipe, Can't flash, cant even get into Cam+power to flash back to previous RC...
Not really sure what to do at this point...
If I do manage to get it running again, I do wonder why its doing this.
I use Cachemate to clear my catche and task killer to kill apps. Could Cachemate be the culprit in this mess, its the only app that I own that uses root? Not sure what else to blame it on other than the G1 one being one big POS and is only good if you can even get a ROM to run on it. I am 5 minutes away from ordering a Nexus.
once again thanks in advance for any input you can provide.
D3AD PIX3L said:
I think I just may have bricked my phone...
I did all the steps stated in my first post while flashing to 4.2.12.2 and got things going great. Flashed Enoch's Theme 4.2.12.2. Everything was rocking.
Then today, it shut it self off, I rebooted. Got to Enoch load screen then shut off, tried it again, and it won't even get past the G1 splash screen. I have had this happen a few times before, where it would power off randomly and I had to pull the battery, wait like 5 minutes and then get into recovery and clear/flash again. Now I am getting into recovery but after a minute or so it just shuts itself off again.
Can't wipe, Can't flash, cant even get into Cam+power to flash back to previous RC...
Not really sure what to do at this point...
If I do manage to get it running again, I do wonder why its doing this.
I use Cachemate to clear my catche and task killer to kill apps. Could Cachemate be the culprit in this mess, its the only app that I own that uses root? Not sure what else to blame it on other than the G1 one being one big POS and is only good if you can even get a ROM to run on it. I am 5 minutes away from ordering a Nexus.
once again thanks in advance for any input you can provide.
Click to expand...
Click to collapse
This sounds like a hardware issue, and not a bricking. Try a new battery, this may fix it, otherwise I am not sure.
cloverdale said:
This sounds like a hardware issue, and not a bricking. Try a new battery, this may fix it, otherwise I am not sure.
Click to expand...
Click to collapse
I will try the other battery I have at home in my other G1 and report back
D3AD PIX3L said:
I will try the other battery I have at home in my other G1 and report back
Click to expand...
Click to collapse
I tried it.
Same issue.
I did noticed that the batter pins were abnormal... One was sticking out more which was normal according to my other G1, the other 2 were shoved down. I tried to mess with the 2 to get them to pop back up to their normal position with no luck.
I am thinking about ordering a replacement.
okay, so tonight I am going to take the G1 apart and see if I can get those pins straightened out. Not sure if it will help, but its better than declaring it a paper weight.
will post the outcome.
Just out of curiousity (and I don't exactly know where I'm going with this) will your phone turn on and stay on if you plug it in (usb or charger)?
borodin1 said:
Just out of curiousity (and I don't exactly know where I'm going with this) will your phone turn on and stay on if you plug it in (usb or charger)?
Click to expand...
Click to collapse
It does not.
I think i will take both phones apart and swap out the screen since that is why I don't use the one. I watched a visual walkthrough seems easy enough
Has anyone disassembled their G1 and reassembled successfully? any tips?
Started to take apart the non-cracked bricked G1.
Once I removed the motherboard and started on the next step, I realized how bad it would be to end up getting the parts swapped and then have it not work... Put it back together and loaded up the latest Cyanogen on my working cracked G1.
*shrugs* it will do for now.
Waiting till the end of next month to order my Nexus 1, then I will have fun ripping apart both G1's and hopefully end up with one great looking, fully functional G1 to possibly sell or keep as an extra phone...
thanks to all who replied!
I've been searching, and reading, and my eyes hurt. I normally don't like to post threads, but I'm left with no choice. If this topic has been covered, then I guess my searchin' skillz are stating to lack. Here is my delimna:
Rooted, Lagfix, enabled Side-loading, recently installed ClockworkMod, stock firmware. I ran a backup using ROM Manager/ClockworkMod. I was attempting to install the Mobile AP fix for WiFi Hotspotting from designgears. I downloaded the new kernel per instructions (Mobile AP ony). I first tried installing it using ROM Manager's boot option into Clockwork without renaming MobileAP.zip. Still received black screen when I open the Mobile AP settings that the new kernel was trying to fix. So I thought that the flash didn't work, so this time I renamed the kernel file to update.zip and did the standard method of flash using stock recovery mode.
Now the phone boots to the Galaxy S screen, then just a black screen. The bottom row buttons seem to be active, but nothing happens. Holding power....nothing. I have to pull the battery; however, I can boot into stock recovery.
Now here's the delimna. I can boot into recovery, but the update.zip file is NOT the one for ClockworkMod, its the modified kernel. Is there a way that I can browse the files on the phone so I can change the update.zip file? I want to put Clockwork's in place so I can restore using my backup made yesterday....It's not a huge order if I have to flashback to stock and lose everything as I usually do that everynow and again anyways (usually I'm prepared). I won't lose anything important that isn't already backed up except maybe some pictures....
BUT, I can't help but try. It's just me I like to break stuff and fix 'em. I want to try to run that backup I made. I have Odin, and I tried flashing the kernel back to stock (i had one hell of a time finding information on how to use it). As a matter of fact, I found instructions on HOW to use it, but I gave up trying to find useful information on how the program runs (like a user guide, what else can it do, that sort of thing....). I spent hours reading thread after thread........information overload I guess.
I figured someone might point me in the right direction. How can I browse/edit the contents of the phone while in Recovery or Download mode?
You could try letting the phone boot up, yes I know it's only a black screen, then plug in the usb to your PC and see if ADB works.
If so then just adb shell into it and work with command line.
I'm not sure if ADB would work in stock recovery mode but that's worth a shot too.
Excellent idea, but no luck. I can get the computer to recognize the phone in recovery mode, but ADB shows the device offline, and Windows Explorer shows 2 drives with the whole "insert disk into drive ..." message. Can't boot phone to enable "development mode", that might have something to do with it......unless I'm missing something?
swedishcancerboi said:
Excellent idea, but no luck. I can get the computer to recognize the phone in recovery mode, but ADB shows the device offline, and Windows Explorer shows 2 drives with the whole "insert disk into drive ..." message. Can't boot phone to enable "development mode", that might have something to do with it......unless I'm missing something?
Click to expand...
Click to collapse
Wasn't sure if that would work or not.
So, if you turn it on and just let it sit as long as a normal boot, then try adb does anything work?
I actually let it sit for ~15 minutes. computer doesn't even register the usb being plugged in. I'm going to give it another go or two, but in about an hour I'm going to have to call it quits and just flash it with Odin. Don't want to give up yet, but I am driving out of town later this afternoon and must have my phone for the trip. Maybe I'll break it again tomorrow and play with it over the weekend!
Let me know if you have any other ideas. I'll let you know when I give up.
While on that subject (watch someone tell me to move my post after this.....), maybe I'll experiment with a new ROM. Any recommendations? (without OC, device is fast enough). I haven't read much on the different flavors available at the moment (I think I read something about a 2.2 from I9000 or something?).
swedishcancerboi said:
While on that subject (watch someone tell me to move my post after this.....), maybe I'll experiment with a new ROM. Any recommendations? (without OC, device is fast enough). I haven't read much on the different flavors available at the moment (I think I read something about a 2.2 from I9000 or something?).
Click to expand...
Click to collapse
Hybrid from eugene is pretty fast especially if you add the voodoo kernel to it. Thats what I heard tho. Because when i tried it out it was pretty quick with out a lagfix and without autokiller. Only used it for 20 min tho as i couldn't get Titanium backup to work. I think the titanium problem is a hit or a miss.
well, I guess I'm going to have to load stock and wipe everything...oh well. Let's see how this goes. Then I'll start playing with ROMs this weekend. Thanks anyway!
swedishcancerboi said:
well, I guess I'm going to have to load stock and wipe everything...oh well. Let's see how this goes. Then I'll start playing with ROMs this weekend. Thanks anyway!
Click to expand...
Click to collapse
Well, if your going to do that take an extra 2 minutes and load Eugenes Hybrid R3 while your at it. It's extremely easy to do and in my opinion the fastest thing we can put on these phones right now.
Vibrant ROM? is that safe? I mean, I know they are all Galaxy S, but is the hardware really that identical?
I don't think eugenes captivate hybrid is actually a vibrant rom. I think he just borrowed some of the better parts.
Sent from my SAMSUNG-SGH-I897 using XDA App
Got it! I used the one click stock down loader to get the phone to boot. I then noticed that many of my files were still there, music, zips.....so I thought....maybe my backup is still there.
Instead of using my original root, I decided to try Unleash the Beast.applied it so I could load Rom Manager.i opened Rom manager and it showed my backup!
I tried restoring then without success (no update.zip) and had to flash clockwork (even though it showed it already loaded, guess it needed to be refreshed, makes sense since it is a fresh firmware), selected my restore and it ran like a charm.
I am just surprised. I thought the act of flashing the Rom would wipe everything. Apparently not if you never do the "master clear."
Thankfully I had just installed Rom Manager the day before and had a fresh backup. Looks liked I'm gonna have to start shelling out more beer money to the devs!
Now I can prepare to break it again and again. Let the fun begin!
Sent from my SAMSUNG-SGH-I897 using XDA App
Nice. Yeah, stuff you have stored on your "internal SD" is safe between flashes. Of course apps, contacts, etc get wiped, but that's an easy fix.
"the more you know," eh? Ha!
Sent from my SAMSUNG-SGH-I897 using XDA App
Phone worked fine with lagfix... but consumed too much battery and I decided to uninstall the lagfix with the mcr script...
Then applications stopped working and it gave errors, so the best thing to do is to reboot I thought NOT
Now it will not boot annymore and it's stuck after the nice Samsung intro after that my screen stays black and the only response is the illuminated keys..
Tried 3-button recovery but that didn't work.. no recovery no download mode..
I have one from The Netherlands, Europe/International version.
PLEASE HELP ??
you can try to flash a stock Euro ROM back into your phone with Odin and repartition enabled
if that doesn't work, then the next best thing is to send the SGS back to repair
How can Odin see my phone? The only thing I can see are 2 external sd card that I can't access.
use the 3 button Download Mode to get into the connection with Odin
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series
instructions on Wiki
How long have you waited for the samsung galaxy s intro to pass ? I had quite a shock myself when I rooted my phone. I just had to be patient and the phone went on to operate as usual after a long initial wait during the time the logo was shown... After that, every subsequent reboot was faster.
I haven't flashed my phone because Odin can't recognize my phone. It just hangs in the boot screen and there isn't happening anything. The phone just gets warm and does nothing... Looks like that lagfix f*cked up my root
Guess I must head back to the store ... and wait ... 2 weeks or more so...
Have you tried the heat fix to get the 3 button working?
Sent from my GT-I9000M using XDA App
Which lagfix were you using?
The One Click Lagfix takes awhile to boot up at first
KaliKot said:
Which lagfix were you using?
The One Click Lagfix takes awhile to boot up at first
Click to expand...
Click to collapse
he's un-installing/removing/deleting the lag fix out of the phone,
not installing it for the first time
AllGamer said:
he's un-installing/removing/deleting the lag fix out of the phone,
not installing it for the first time
Click to expand...
Click to collapse
You're right. After I heard it consumed very much energy I decided to UN-install the lagfix which messed up my root by partitioning it wrong...
Brought it back to the store today so I hope to have it back soon!
Then after delivery I will make sure I can access the 3-button combo!
same here. damn it, my JF5 don't have 3BR
already sent to SGS last friday. hope that I will get it back on this week.
We should tell others that who installed LagFix
DONT TRY TO UNINSTALL IT Unless you got your time to wait.
NXJeff said:
same here. damn it, my JF5 don't have 3BR
already sent to SGS last friday. hope that I will get it back on this week.
We should tell others that who installed LagFix
DONT TRY TO UNINSTALL IT Unless you got your time to wait.
Click to expand...
Click to collapse
Yeah that will be a very smart thing to do!
The main guideline will be: Don't do anything stupid before you can access the recovery and download mode
Got my phone back, but still hecitating to do the 3-button flash since there are more people that have bricked their phone with it.
Hopefully the Froyo update comes soon! (in one of these days )
i rooted my NC with 1.1.0 and everything was perfect. installed and backup with CWR v 3.0.0.5. I have been stuck in the two screens of cwr. I CANNOT TURN off the nc so 8 aborted on/off s do not work. I cannot restore from sd card since it boots back into cwr, so i have not been able to use any removal code. the Monster pack is not for 1.1. I think I may be bricked. How do I get out of this clockwork recovery program (i have tried all of the options in it too, including fixing permissions, recoveries and endless useless reboots. HELP!
Hold the power button and it will turn off.
i have done that but it turns itself right back on again. it will not stay off. when it does go back on, it goes right back into clockworkmod recover (orange menu screen, landscape only)
Try going here and see if that gets you out of trouble .. Hope it helps
I can't say for a fact that this will make a difference for you, but it certainly can't hurt. Make sure you plug in your Nook Color to the charger, then do the manual power off (as in hold the power button). That should force it to reboot.
Those were the instructions I was given when CWR froze up on me during a kernel flash and it worked. Good luck.
got any mortar-bricked!
got it tuned off. now totally dead.. does not respond to power switch at all now. beware of CWR!!!
Boot CWR off monsterpack SDcard and restore stock system.img/boot.img. This saved me. This is definitely auto-nooter 3.0.0 related because pre-rooted BN 1.1.0 flashable does not have this problem.
ddd22 said:
got it tuned off. now totally dead.. does not respond to power switch at all now. beware of CWR!!!
Click to expand...
Click to collapse
no can do...cannot be turned on. stone dead
It is not. Trust me, I've has this thing twice today. boot partition on emmc is messed up I guess. You CAN boot from CWR on SD card.
ddd22 said:
no can do...cannot be turned on. stone dead
Click to expand...
Click to collapse
With all due respect, I dont understand how that can be. When I press, or press and hold the power key, nothing at all happens. no screen or light activity of any kind... like someone removed a battery.
After your reply, thinking perhaps my removed micro sd card might make a difference, i put it back in and tried again to power on the NC.. nothing happens still. Are you telling me that somehow if i change the content of my SD card to the Monster Pack that somehow that firmware code is going to turn on the Nook even though i cannot power cycle it at all without that magic? I dont understand how this could be and creating that card is a fairly steep search and discovery mission for me which i am willing to do if it has a chance of working.
btw, the battery is fully charged according to the green N on the usb cable.
Thank you so much for your response.
zdrifter said:
Try going here and see if that gets you out of trouble .. Hope it helps
Click to expand...
Click to collapse
What he/she said.. Happened to me once today. Remove the CWR and you should be good to go
how do i do that when no matter what i do the NC will not power on at all...zero. I can no longer even establish a usb connection to the computer.. it detects something and then tries and fails to install required drivers (which were previously installed and previously working). As much as I wish you all are right and I am missing something, I think I may be the first fool to brick the unbrickable!
You will need to make a bootable SD card and boot off that.
i made a bootable cwr sd from the monster rootpack. same nothing happens. will not power on in any way shape or form. will now remake the card with the full rootpack and pray that i can eat my words.
chomp chomp chomp
(the glorious sounds of words being eaten). you both were 100% correct and trust you i should have even more. I followed your advice despite my doubts and I wrote the rootpack image to the sd card and held the power button for about 15 seconds and alive she came! now i am at least back to my cwr that i cant get out of. i now could use a little more of your wisdom as to the best next steps. should i remove cwr then reflash with say 1.1.0R2 or should i figure out how to use cwr to do that flash, and remove it after the flash is completed. obviously a newbee to flashing this device (less than a week old), but have been following Energy on HTC flashes for long times. There is so much information here, it is almost too much when you first step in and your collective willingness to help this doubting thomas is extremely appreciated. my apologies and my deepest thanks. more reading coming up..
resolved!
i added the zip for 1.1.0 -r2 to the monster sd boot card and installed the rom from there. setting it up now. thanks to all for not listening to my doubt and telling me to continue as instructed. forever grateful
ddd-22 - did you install from CWR after rooting 1.1 using the modified Autonooter, or did you sideload the rooted 1.1?
I installed CWR from a 1.1 that was rooted using Autonooter (modified for 1.1) and ended up in a CWR reboot loop similar to what you had.
Yeah- I attempted to run the OC rom after autonootered to 1.1 and got into the loop. Has anyone had succes in loading the OC rom after autonootering to 1.1? Thanks
Thank you for this thread. The exact same thing happened to me after trying to flash a kernel using CWR and autonooter3.0. Thought I was bricked for sure!
I am back to business and glad not to have an expensive paper weight!
though i am on the way to recovery, not fully there yet. the r2 prerooted version was great except i could not log onto gmail... it kept seeing the NC as a phone and was looking for a cellular network, and gave me the message "a reliable connection with google servers could not be made" or some such verbage.. In the pre rooted 1.1. r2, i followed the directions going through youtube etc, but that did not work. so i decided to try to restore the backup i made when i first got caught in the doloop. which i did again, so it is back to monster to start over again and clear out the NC. I have been scouring other sites and many people have been having this problem. I wish i could remember how i installed cwr (method) but cant. however, what i found fairly consistently, and i believe i made the same mistake, was not restarting the NC before i made the backup. seems that is what got a lot of folks into this doloop crisis. if anyone has a plan of how i should get back to my previous state of bliss, let me know. I am remaking monster pack again and clearing out my machine.
Sorry for the long read, this is half rant and half question.
Alright, I got a captivate a long time ago (about a year and 3 months ago), loved it, rooted it and installed cyanogenmod as soon as I got home, changed roms and kernals constantly, did whatever I wanted to do.
About 3 months ago my screen stopped working.. So I take it in and they give me a refurb captivate, looked brand new so I didn't mind. However, when I tried to get into recovery it didn't work, the 3-button-method just wouldn't work at all, period, so I try to get it to work, gets stuck in bootloop.. pretty much every time I try to flash a rom something goes wrong and I get stuck in a bootloop but I can usually get into recovery or download mode because I had CWM.
So I'm on maxq's rom and it's working great for the past 2 months, decide not to mess with kernals or anything, however today I decided to try ICS, load it up, everything's fine, then I realize my soft keys aren't working, search for awhile, can't find anything, finally just manually start looking through the rom pages, and someone said that if you have the problem to just odin back to stock and try again.
I odin back to stock, but now 3 button combo doesn't work.. So more searching, find that I can run the 3e fix by TRusselo, doesn't work because I need root, more searching on how to root without recovery, find "SuperOneClick", root with superoneclick, then run 3e fix, everything is working fine, I check my email and load the ICS files onto SD card, go to restart and go into recovery mode.. Bricked, stuck in a bootloop, won't go to recovery, won't go to download, nothing.
Why the **** was I able to do anything I wanted with my old captivate, but if I even root this one it bricks? And what did I do to even brick it? I only ran the 2 programs and both of them worked flawlessly.
I guess my only option is to usb jig it, but honestly now I'm convinced that the phone is just faulty, I want to run the thing over.
-Pirate said:
So I'm on maxq's rom and it's working great for the past 2 months, decide not to mess with kernals or anything, however today I decided to try ICS, load it up, everything's fine, then I realize my soft keys aren't working, search for awhile, can't find anything, finally just manually start looking through the rom pages, and someone said that if you have the problem to just odin back to stock and try again.
Click to expand...
Click to collapse
If you would have actually searched you would have known it was a bug in the glitch. There are atleast 40 pages about that.
-Pirate said:
I odin back to stock, but now 3 button combo doesn't work.. So more searching, find that I can run the 3e fix by TRusselo, doesn't work because I need root, more searching on how to root without recovery, find "SuperOneClick", root with superoneclick, then run 3e fix, everything is working fine, I check my email and load the ICS files onto SD card, go to restart and go into recovery mode.. Bricked, stuck in a bootloop, won't go to recovery, won't go to download, nothing.
Click to expand...
Click to collapse
If you flashed ICS you should know it takes 2 flashes for it to work first time. Having a jig around is always a good idea as well.
-Pirate said:
Why the **** was I able to do anything I wanted with my old captivate, but if I even root this one it bricks? And what did I do to even brick it? I only ran the 2 programs and both of them worked flawlessly.
Click to expand...
Click to collapse
Stuff doesn't work as intended. Keep in mind everything is still in dev and not all devices are the same. But you should have searched a little more and it would have ran =/
U def don't need a jig. If it's booting it's not bricked. Try removing battery, start Odin, hold down power and down, plug in and put battery in. This should bring u to download mode.
prbassplayer said:
If you would have actually searched you would have known it was a bug in the glitch. There are atleast 40 pages about that.
Click to expand...
Click to collapse
I did start to see a few people with the problem, however many people do not follow up with what fixes their problem, and I did what a few people had said to do.
prbassplayer said:
If you flashed ICS you should know it takes 2 flashes for it to work first time. Having a jig around is always a good idea as well.
Click to expand...
Click to collapse
I should of mentioned that I did flash a few times, 3 total I think, it was getting stuck at boot.
prbassplayer said:
Stuff doesn't work as intended. Keep in mind everything is still in dev and not all devices are the same. But you should have searched a little more and it would have ran =/
Click to expand...
Click to collapse
I understand that **** happens but honestly my old captivate could always get into recover mode and download mode no matter what, it's extremely frustrating that something changed with the newer models. One of my questions was what caused the brick? I did nothing wrong from what I see and it was running perfectly until I tried to restart/boot into recovery.
Oh and mbc663, thanks but download mode doesn't work at all, nor does recovery obviously.
I can't say exactly what you are doing. Best advice I can do Re download your .zips Flash back to stock GB and try again.
-Pirate said:
About 3 months ago my screen stopped working.. So I take it in and they give me a refurb captivate, looked brand new so I didn't mind. However, when I tried to get into recovery it didn't work, the 3-button-method just wouldn't work at all, period, so I try to get it to work, gets stuck in bootloop.. pretty much every time I try to flash a rom something goes wrong and I get stuck in a bootloop but I can usually get into recovery or download mode because I had CWM.
So I'm on maxq's rom and it's working great for the past 2 months, decide not to mess with kernals or anything, however today I decided to try ICS, load it up, everything's fine, then I realize my soft keys aren't working, search for awhile, can't find anything, finally just manually start looking through the rom pages, and someone said that if you have the problem to just odin back to stock and try again.
I odin back to stock, but now 3 button combo doesn't work.. So more searching, find that I can run the 3e fix by TRusselo, doesn't work because I need root, more searching on how to root without recovery, find "SuperOneClick", root with superoneclick, then run 3e fix, everything is working fine, I check my email and load the ICS files onto SD card, go to restart and go into recovery mode.. Bricked, stuck in a bootloop, won't go to recovery, won't go to download, nothing.
Why the **** was I able to do anything I wanted with my old captivate, but if I even root this one it bricks? And what did I do to even brick it? I only ran the 2 programs and both of them worked flawlessly.
I guess my only option is to usb jig it, but honestly now I'm convinced that the phone is just faulty, I want to run the thing over.
Click to expand...
Click to collapse
Last year, I had issues with my original Cap, and got a "new" one. I learned that the bulk of the Caps going out as replacements are referbs. The one I got was a 1008 build, and does not have 3 button recovery. There are minor differences with each and every Cap that's out there. That's why some have issues with ROM's and some don't, some can over clock like crazy, and some can't at all. My guess is you have a 1008 as well, but that really doesn't matter. You just have a different device and as you seem to already have learned.
It sounds like there is more research you need to do. Even though the devices are a bit different, if you are having issues with ROM's loading, then I would say it's more of a procedure issue, than one with your device.
My procedure, is,
Remove SD/Micro SD
Odin1 Click to Stock JF6, and Master Clear(This will erase EVERYTHING)
Root with One-Click Root
Use Sideload Wonder Machine to install ROM Manager, copy update.zip and 3buttonFix to my SD, then reboot into recovery
Once in recovery I install the 3buttonFix, and install my new ROM
For me this has proven to be a very good method versus going from one ROM to another. The Master Clear cleans EVERYTHING off of your SD, so there is no chance for anything to corrupt your new install. Anytime I read a post of a install gone FUBAR, USUALLY a Flash To Stock/Master Clear (FTS/MC) fixes it
Before using Odin 1 Click, check your devices build number!! If it is higher than 1012, I would NOT recommend using 1 click, there is a higher chance of hard brick on the newer devices
Kangi...if you flash a firmware package without bootloaders, you won't have to do the 3 button fix every time. And if you keep a copy of the update.zip on your pc you don't have to even root, let alone bother with side loading ROM manager.
Cezar has a no boots jf6 and after you run that, you can still use master clear in one click.
Sounds like you got one of the refurbs that is missing the SBL. Have you looked at this thread? http://forum.xda-developers.com/showthread.php?t=1129821
I've not had this problem myself but it sounds like that might help. If I remember reading correctly, once this is flashed it should stick as long as you don't flash any other bootloaders on top of it.
Its not missing the sbl. The sbl it has doesn't respond to key combos. Derpa sherpa moment for samsung I guess?
Rofl yeah...if it was missing the sbl it would be fuggin bricked!
studacris said:
Kangi...if you flash a firmware package without bootloaders, you won't have to do the 3 button fix every time. And if you keep a copy of the update.zip on your pc you don't have to even root, let alone bother with side loading ROM manager.
Cezar has a no boots jf6 and after you run that, you can still use master clear in one click.
Click to expand...
Click to collapse
I know, thanks. I'm such a creature of habit, I started doing it like this a bit over a year ago, and has worked flawlessly for me(just jinxed myself!) so I never saw a reason to "fix what aint broke".
I'll take a look at Cezar's thanks!
Yeah, missing SBL was a poor choice of words. My bad.
kangi26 said:
Last year, I had issues with my original Cap, and got a "new" one. I learned that the bulk of the Caps going out as replacements are referbs. The one I got was a 1008 build, and does not have 3 button recovery. There are minor differences with each and every Cap that's out there. That's why some have issues with ROM's and some don't, some can over clock like crazy, and some can't at all. My guess is you have a 1008 as well, but that really doesn't matter. You just have a different device and as you seem to already have learned.
It sounds like there is more research you need to do. Even though the devices are a bit different, if you are having issues with ROM's loading, then I would say it's more of a procedure issue, than one with your device.
My procedure, is,
Remove SD/Micro SD
Odin1 Click to Stock JF6, and Master Clear(This will erase EVERYTHING)
Root with One-Click Root
Use Sideload Wonder Machine to install ROM Manager, copy update.zip and 3buttonFix to my SD, then reboot into recovery
Once in recovery I install the 3buttonFix, and install my new ROM
For me this has proven to be a very good method versus going from one ROM to another. The Master Clear cleans EVERYTHING off of your SD, so there is no chance for anything to corrupt your new install. Anytime I read a post of a install gone FUBAR, USUALLY a Flash To Stock/Master Clear (FTS/MC) fixes it
Before using Odin 1 Click, check your devices build number!! If it is higher than 1012, I would NOT recommend using 1 click, there is a higher chance of hard brick on the newer devices
Click to expand...
Click to collapse
I didn't think anyone else was going to reply to this thread, whoops.
Thank you for helping me, but I'm still having trouble.
Rom manager doesn't show up in Market, Sideload wonder machine tells me [INSTALL FAILED OLDER SDK] with any apk of Rom manager I find.
kangi26 said:
3buttonFix to my SD, then reboot into recovery
Click to expand...
Click to collapse
How do you reboot into recovery when 3buttonfix hasn't been applied yet?
This sucks and is extremely frustrating, I feel like my captivate is just trolling me.
-Pirate said:
I didn't think anyone else was going to reply to this thread, whoops.
Thank you for helping me, but I'm still having trouble.
Rom manager doesn't show up in Market, Sideload wonder machine tells me [INSTALL FAILED OLDER SDK] with any apk of Rom manager I find.
How do you reboot into recovery when 3buttonfix hasn't been applied yet?
This sucks and is extremely frustrating, I feel like my captivate is just trolling me.
Click to expand...
Click to collapse
When I get home later tonight I'll link you everything you'll need. Again, VERY important, what is your build number? If it's 1012 or higher, don't use Odin 1 click
Sent from a autonomous device
kangi26 said:
When I get home later tonight I'll link you everything you'll need. Again, VERY important, what is your build number? If it's 1012 or higher, don't use Odin 1 click
Sent from a autonomous device
Click to expand...
Click to collapse
Ok, finally got it working, I did exactly what you said, I found the rom manager 3.00.002 or whatever and that worked with sideloader, it took some messing around with but I'm running ICS now, thank you so much man, you've helped me so much, and now I can change roms and keep up to date without worrying about constantly soft-bricking.
As for my build number, I'm not sure, the only thing I see under build number in settings is: "IML74k"
-Pirate said:
Ok, finally got it working, I did exactly what you said, I found the rom manager 3.00.002 or whatever and that worked with sideloader, it took some messing around with but I'm running ICS now, thank you so much man, you've helped me so much, and now I can change roms and keep up to date without worrying about constantly soft-bricking.
As for my build number, I'm not sure, the only thing I see under build number in settings is: "IML74k"
Click to expand...
Click to collapse
The build number is actually under your battery, and looks like 10.06, 10.07, 10.08 and so on. It is the production date
Edit** And as a side note, do NOT try to use the 3buttonFix with a GB ROM, it WILL brick your phone in a really bad way. ONLY use it with 2.1 or 2.2
kangi26 said:
The build number is actually under your battery, and looks like 10.06, 10.07, 10.08 and so on. It is the production date
Edit** And as a side note, do NOT try to use the 3buttonFix with a GB ROM, it WILL brick your phone in a really bad way. ONLY use it with 2.1 or 2.2
Click to expand...
Click to collapse
Is it weird that I don't have a build number? It seems I can't post pictures without a few more posts, maybe this will work: deleted
And thanks for the warning on the 3buttonfix, I'm going to have to read more about bootloaders though, I don't understand what you and studacris were talking about earlier in the thread, haha.
-Pirate said:
Is it weird that I don't have a build number? It seems I can't post pictures without a few more posts, maybe this will work: imgurDOTcom/26sXGl.jpg
And thanks for the warning on the 3buttonfix, I'm going to have to read more about bootloaders though, I don't understand what you and studacris were talking about earlier in the thread, haha.
Click to expand...
Click to collapse
I havent seen that before, there doesnt seem to be a build#
Might want to pull that photo, it's not too good having your IMEI number publicly displayed
kangi26 said:
I havent seen that before, there doesnt seem to be a build#
Might want to pull that photo, it's not too good having your IMEI number publicly displayed
Click to expand...
Click to collapse
Maybe because it's a refurb? and whoops didn't think about that.
-Pirate said:
Maybe because it's a refurb? and whoops didn't think about that.
Click to expand...
Click to collapse
I'm not sure why, mine is a referb, and I have a sticker with mine on it. Ooh well, it is what it is
Sent from a autonomous device