Related
aladin2000 said:
Hi,
do you tried also a buttom to call with voice command application or a phone call ?
I've a HTC S100 and the sound is well but it's very difficult to start a voice commande or to recall last call because seem that the function "hand free" sometime is lose.
Sorry for my poor English !
Regards
aladino
Click to expand...
Click to collapse
I have the same problem with my handsfree headsets an Tytn II (kaiser):
i have a motorola H700 and a Scalarider headset for helmets.
They are bot NON-ADP and thyey support handsfree.
Sometimes the button on them stop working and I can't do voice dialing with Voice command neither repeat last call.
They appear as connected and If I manually call a number they work.
To get the button works again I have to restart the phone.
Maybe a fault in the microsoft bluetooth stack?
Also: my Motorola H700 has a flip and when you open it the headset turn on and get connected.
You should be able to answer phone calls by opening the flip.
Sometimes it works, but most of the time it doesn't connect if I open it while the phone is ringing and in that case I have to restart bluetooth connection to make it work again.
Microsoft or HTC should check end improve bluetooth stack!
Any hack around?
Can't we put the broadcom instead of microsoft stack on kaiser?
I wrote to HTC Support about this problem and they answered :
"Customer email address:XXXXXXXXXX
Good Afternoon,
The multi function button is the one small button with the led light in, not the big play/pause button.
If you try the other button, it should work.
Thank you for your enquiry, Should you have any other problem, please do not hesitate to call us. Your Local number can be found at http://www.europe.htc.com/support/csbyphone.html
Best regards,
XXXXX
HTC Europe
[email protected]
http://www.htc.com "
That's incredible don't you ?
They beleive I'm idiot ?
Regards
aladino
Astonished!
Amazing answer!
Are they idiot?
I'll write them too,
I hope someone cleverer will read the my mail
and suggest the bug to the technical stuff.
I have a motorola H350 and have been experiencing the same problems. It's driving me mad. The problem makes the use of the hands free totally useless as it seems to stop working at the drop of a hat.
What I've found so far.
To get it working you need to turn on the ear piece.
Then turn on the bluetooth on the phone.
If you do this any other way it doesn't work. Once it's working you may or may not be able to hang up with the button. If that's the case it won't answer with the button either.
Once it's working it seems to work ok till either the headset or the phone's bluetooth is turned off.
Voice dial will not fire up until the main procedure if followed and sometimes it takes several tries.
I was wondering if this was something to do with the motorola but seemingly it's to do with the stack so getting another device isn't going to help I guess.
The bluetooth worked perfectly on the Hermes but immediately I got the Kaiser one thing alerted me to the fact that something was different.
With the Hermes, as soon as I turned on the bluetooth and the earpiece the phone would alert me to the fact that the motorola wanted to connect.
With the Kaiser nothing, even when I searched for a device. I had to find out how to put the earpiece into search mode before it would find it.
Very flakey and very disappointing. I hope someone finds a fix for this.
Anyone else experiencing these problems?
I've got an H700 and Jawbone. I do notice more crackle type sounds and lower volume on both using Kaiser compared to my 8525. The H700 connects within 1-2 seconds when opening it's flip and I have noticed that on occasion, if I walk away from the phone (eg. phone on desk) the headset may not reconnect when I return. The Jawbone has been fairly good at connecting and staying functional at all times but the volume is lower as noted by many people.
I would say that the stack overall is better than the 8525's for all the devices I've tried (3 headsets, 2 Laptops, 1 Garmin Streetpilot with BT Phone interface)
I am also losing the Voice speed dial & redial button from time to time. It also worked that way with my hermes, so I kinda get used to it...
I am now wondering if it is related to my BT earpiece (nokia bh-200 or something like this) of if it is the BT stack which has never been really working on all the device I could test (hermes, trinity, kaiser).
I allmost never had issue recieving call (I don't recieve much call while using the BT earpiece) but it is sometime impossible to initiate a call through the BT earpiece.
The simplest way for me to lose the voice recognition is to:
-Start BT on the phone
-Start BT earpiece
Phone recognize the earpiece, everything is fine
-Restart the phone
Phone & BT reconnect, but voice recognition & redial are gone
I would really appreciate of some of you could test my little procedure and report if it works of not. If it is working for some other BT earpiece I may change mine and get rid of this eternal annoying issue.
Thanks
Jabra BT500
I have the Jabra BT500 and same problem with the TyTn II.
The earpiece can't initiate a voice call...
Looks like HTC (or Windows), starts to deliver ROMs like Mr. Bill Gates does with his M$ crap...
If someone find a solution for this Bluetooth problem, please post it!!!!
Thanks a lot,
Kaiser and Moto H700 just do not work together
I also have a problem with the Kaiser and a Moto H700. The M700 button stops working randomly, the BT connection sometimes disconnect during the call at will.
I can still use H700 successfully with my old Nokia 6680, so the problem clearly is in the Kaisers BT stack.
I’ve made the BT update that HTC posted just recently for TyTN II, but it had no effect.
Fortunately, I have my old Moto H500. This one is working OK with the Kaiser, but. Like it was pointed here before me, the only way to get it working you need to turn on the ear piece. Then turn on the Bluetooth on the phone.
In case if the Bluetooth connection was disrupted for some reason, the only way to make it work is again swath Kaiser BT off then turn on the ear piece and switch on the TyTNs BT.
The Kaiser’s BT stack is not good also connecting with a PC, the connection is just not stable.
Just wanted to chime in and say I've had the exact same problems with my Tilt and Motorola H700 as various people have described here. I posted about it on the AT&T forum too, and no one there has any working solution either, AFAIK. I too tried the "fix" from HTC, and to no avail.
This is a pretty big disappointment for me; I love my Tilt, but Bluetooth is not new technology, and it's really inconvenient that it works so poorly on this phone.
Motorola headsets seem to have a problem with this device. I had trouble getting my H500 to connect and the voice button to work. Once I reset the phone when the headset was on and it wouldn't connect. I tried deleting and re-pairing. It took another reset to get it back. Fortunately I don't use that headset anymore.
jameselee said:
Just wanted to chime in and say I've had the exact same problems with my Tilt and Motorola H700 as various people have described here. I posted about it on the AT&T forum too, and no one there has any working solution either, AFAIK. I too tried the "fix" from HTC, and to no avail.
This is a pretty big disappointment for me; I love my Tilt, but Bluetooth is not new technology, and it's really inconvenient that it works so poorly on this phone.
Click to expand...
Click to collapse
The same problem.
But this time with the Sony Ericsson BT HBH - DS980.
I also put the "fix" from HTC, I gave them back and they change them with another brand new Sony Ericsson BT HBH - DS980, but the problem exists.
costas2by4AIO said:
The same problem.
But this time with the Sony Ericsson BT HBH - DS980.
I also put the "fix" from HTC, I gave them back and they change them with another brand new Sony Ericsson BT HBH - DS980, but the problem exists.
Click to expand...
Click to collapse
I just bought the same headset... cant get it work with the TyTN II - Kaiser but pairs without any problem with my TyTN I - Hermes... clearly it is the BT Stack
Way beyond my abilities, but cant the BT stack on Hermes be cooked into a rom for the Kaiser ?
I have a Motorola HT820 and a Motorola S9 both devices are working flawless with the kaiser.
Now i own a motorola S705 too , with this device my kaiser suddenly turn the bluetooth off (
regards
Anyone else got this issue and is there a new bluetooth stack or something to resolve it?
When I click the answer button on any bluetooth headset (currently using the iqua solar powered one), the sound is temporarily diverted to by mobile before the bluetooth properly picks up, and also during that slugging moment, any ringtone playing is diverted to the caller's earpiece (i.e. sent out by my mic).
One caller complained it had nearly deafened them.
Anyone able to help?
Having the same issue with my parrot bluetooth and my Tilt
Can someone purrlleeeease help with this issue? I am now scared to answer any calls, lest I get shouted at with, "GOD WHAT WAS THAT NOISE? IT NEARLY DEAFENED ME!"
You really haven't give a lot of info here.
I mean what Rom are you running, what BT hardware and reg tweaks do your use etc.
Info is required to be of any assistance.
Note my signature shows exactly what Rom(s) I'm currently using.
Many thanks. Here are my versions:
HTC TyTN II
ROM: 1.0 Sleuth
ROM date: 08/28/07
Radio version: 1.27.12.11
Protocol version: 22.45.88.07H
Essentially I think a new Bluetooth stack might solve it, but I really wish to avoid losing all data by flashing a new ROM altogether.
A new Bluetooth stack on its own would be wonderful... or a way to restore my data back to a newer ROM. Would Sprite Backup do that if I use Sleuth's WM6.1 ROM?
CJSnet said:
Would Sprite Backup do that if I use Sleuth's WM6.1 ROM?
Click to expand...
Click to collapse
I know the commercial version is supposed to support "Rom Upgrade" support but I'm not sure if that is in the version that is floating around the forums.
What you can do though is make a backup prior to upgrading.
Then upgrade to test if the problem is fixed in one of WM6.1 roms.
Then downgrade and restore your back-up.
Now you will know if there is even a point to expending the effort of trying to extract the BT Stack.
Don't take offense at this next statement but if you put forth that effort it might endear someone more skilled to your cause as you've provided a "Proof of Concept" so to speak.
Okay I have just upgraded to Sleuth's v3 (WM6.1). Sadly the bluetooth issue remains, despite the new Radio version.
If someone calls, and I answer using the bluetooth headset, for 1 second their audio is output to the speaker of the Kaiser. I believe it is during that second that they also hear the end of the ring tone, which is what deafens them.
An unsatisfactory workaround is to use a quite ringtone or vibrate only, but that is hardly ideal. If anyone knows of any other solution or a bluetooth stack that is a bit snappier when answering via headset, it would be great appreciated
CJSnet said:
Okay I have just upgraded to Sleuth's v3 (WM6.1). Sadly the bluetooth issue remains, despite the new Radio version.
If someone calls, and I answer using the bluetooth headset, for 1 second their audio is output to the speaker of the Kaiser. I believe it is during that second that they also hear the end of the ring tone, which is what deafens them.
An unsatisfactory workaround is to use a quite ringtone or vibrate only, but that is hardly ideal. If anyone knows of any other solution or a bluetooth stack that is a bit snappier when answering via headset, it would be great appreciated
Click to expand...
Click to collapse
Same issue here with the same new ROM.
I'm having the same problem. When I push the button on my BT HF it gives a horrible noise to the caller at the other end for a second. In my case I doubt it is ring tone, it doesn't sound anythin like the tone I'm using, it's just like loud crackling or smth.
I can't give you any version numbers cause by TyTN II is sent off to warranty (3rd time already). This time it stopped accepting and making calls while showing 3G symbol. Previously I had band selection on auto and had no problems. Now even after hard reset no calls could be made so off it went again. The first two faults where the speaker and the "Fn" light.
I am having the same problem, the handet is at HTC's repair facility for this and a few nagging issues. I will report what they find.
Mine isn't so much the ringtone it just sounds like a loud static sound. I thought it was the headset but I tried it with 3 different headsets and the Bluethooth in my car and they all have the same problem.
Got my phone back today and I can't say I'm impressed with HTC. First they requested that I send it in the original box then must have thrown it out and sent it in some crap box without enough padding. They didn't even send a note or invoice saying what had been done, which was nothing.
They claim they couldn't find anything wrong and when I called support the guy thought it a joke.
Needless to say it is still deafening and I am pissed.
Same Issue Here... It is almost as if there is a dely in cutting off the WAV/WMA file. Bluetooth Picks up and and both parties get the end of the ring tone.
Had the issued with the origional AT&T rom
Have the issue with Slueth 3.0 and Alex 5.2
If anyone finds a fix please let me know...
I am using PhoneAlarm - Don't know if that is related.
I've had the same complaints from some of my callers, and try to answer between rings as much as possible. The complaints have gone way down. Of course, we shouldn't have to jump thru hoops to answer our phones!
Does anyone have contact info to point HTC to this worrying thread? We need a patch release ASAP. A phone that can't answer calls properly? Yikes.
No issues with my BlueAnt Z9. Have you guys tried different headsets?
I think you may have just been lucky. It is uncommon to A) answer during the ringtone, and B) have the caller complain about the loud noise.
It happens on my Bluetooth earpiece, and Nokia car kit, and JVC car kit. So, it is for HTC to resolve.
I've tried three headsets and it happens on all of them. It happens even when I have the phone on vibrate.
I spent an hour on the phone with HTC support and they are awful, even after telling her that it happens on three different headsets she says that is sounds like a headset issue not an issue with the phone.
When I explained for the third time that I would agree if it happend with one headset but since it happens with all of the headsets it would support my arguement that it is an issue with the phone.
It was like talking to a wall. I wish I had an alternitive to HTC at this point, I love their design and have never had a problem with any of their other phones but this their lack of support is amazing.
I think its with all HTC phones. Happened with my Dash - Wing and now Tilt.
But I've never had anyone complain about hearing music on their end...I can just hear it on my headset for about 1 sec. I've also had my SMS tone play wile on a call and also my VM tone play while on a call and I've asked them if they heard that and they said no.
I also only use noise cancelling headsets.
VooDoo1 said:
I think its with all HTC phones. Happened with my Dash - Wing and now Tilt.
But I've never had anyone complain about hearing music on their end...I can just hear it on my headset for about 1 sec. I've also had my SMS tone play wile on a call and also my VM tone play while on a call and I've asked them if they heard that and they said no.
I also only use noise cancelling headsets.
Click to expand...
Click to collapse
I've never had a problem with any other handset, I've had a Qtek 9100, MDA, O2 Exec, Wing and a Dash.... crap I spent a lot on phones. The only one I've had problems with is the TyTNII.
Same problem here. And sometimes the speaker will very briefly go into speaker mode as I answer! Not good.
Hi everyone. I have had my Tilt for 4months now and it has given me a lot of joy. I have flashed and reflashed with no problems at all. I am currently using Schap's 4.31 Rom with 1.27.12.11 radio.
About a month ago i installed a new car stereo that has bluetooth connectivity with my phone - worked like a charm, paired very easily and generally appeared to be working with no probs.
Then i noticed that if i was in a bluetooth conversation and somebody else was calling (on call waiting), if i switched calls i could not hear anything, and if i ignored the second call, when the person on call waiting hang up, both conversations were terminated. I thought it was odd, but i just deactivated call waiting and thought, "let them try calling me later".
The other, a lot more serious problem, is that sometimes, randomly as far as i realised, the phone will go totally silent - incoming calls won't ring, and when i try to make a call, when i press "talk" then phone does not make that beep that it makes when an outgoing call is initiated. Should the person i call pick up i cannot hear them at all.
A soft reset takes care of this problem, but it has happened to me 3 times already, and i think it was after a bluetooth call.
Has anybody faced this problem before? I need to be available on the phone 24/7 due to my work and i really need to find a solution for this. Yesterday afternoon i took a nap for 45 minutes and had six missed calls that i never heard cause the phone never rang.
The phone is always on "ring" and at full volume.
Any ideas would be welcome.
Thanks
Alkis
Same issue
I'm assuming since I also am facing this same problem that it is not uncommon. It seems to me that it happens after a bluetooth device is turned off. Somehow it sets the volume on everything to mute. I thought only a soft reset would fix it until I discovered that it was just shutting off the volume. Still annoying, though.
Tilt problems with phone going silent
This problem has occurred with my phone every since upgrading to the WM 6.1 and it is related to a bluetooth device being hooked up. Often when someone calls the ringer will go from vibrate to on, but the volume turns all the way off. It will then cycle to off completely. The cycling occurs when a call comes in or when I hang up. I can stop this problem from happening by disconnecting the bluetooth head set. I have tried three different headsets and the problem occurs with all of them (Jawbone I, Jawbone II, and Plantronics) so I know it is not the brand of headset. HTC said to try a download of a screen dimmer problem, but have not done that yet. Anyone have any better advice?
did u guys ever find a solution to this?
its quite annoying missing calls because my phone decides to go silent for some reason
Same issue with GPS
I have the same issue, even when using software that accesses the GPS via bluetooth port. Muting is irritating, but at least voicemail catches messages. What really bothers me is that sometimes the mute is turned off and the volume up, especially when in a private meeting where we do not want interruptions
Gregg
HTC Tytn II bluetooth causes silent setting
I too have had the issue where my phone will go into total silent mode after using my bluetooth stereo hands-free feature. It doen't happen after using my bluetooth headset though.
It happens pretty regular that after using the bluetooth hands-free of my JVC car stereo that when I take the phone elsewhere it is totally silent. no ringer, no alarm (Ptravel alarm is what I use), no audio if I make a call (or receive a call).
It also will cause the phone to be silent on subsequent calls on the bluetooth stereo hands-free: ie: I take a call, hang up and another call will come in and I can answer it but have no audio.
My Tytn II is running the HTC (AT&T) WM 6.1 upgrade. The only thing I have done is use the Advanced configuration manager and the Kaiser tweak to change a few settings for performance and visual enhancements.
I see others are having the same problems.....Has anyone else used the tweaks and maybe that is root of the problem?
Has anyone discovered a fix (really important). My only options are to soft reset every time I get out of the car or not use the JVC bluetooth capability (which is why I replaced the stock radio in the first place).
Thanks
Hi rrackman,
I'd advice for you to look at the following thread:
http://forum.xda-developers.com/showthread.php?t=438457
It's quite long, so better subscribe to it and wait for responses. Several people with Tilt's have the same problem. Myself I have a JVC NX-7000 and an unbranded Kaiser (HTC TyTN II). It works fine with WM6.0, but I have the same issues you mention with WM6.1. First advice while we're searching for the solution: downgrade to WM6.0...
Regards,
Nika.
Is there a solution to this problem?
Try WM6.0 ROM - check out the thread I mention in my sig.
Regards,
Nika.
I did indeed take a look at the thread you linked earlier. Sorry for making the quick post earlier, I should have mentioned that this is regarding the "unexplained volume drop to zero" symptom, not the NSI symptom. Fortunately I don't have the NSI problem, just the drop to zero problem.
Of course downgrading to 6.0 would be the key solution, was just hoping to find a way to avoid doing just that. My phone never had the problem prior to 6.1 and was running the exact same list of applications and settings.
Hello. I've been relentlessly searching everywhere for a solution to my plight.
My Diamond touch works fine for the first few incoming and outgoing calls but then all of a sudden there is no incoming or outgoing audio when I make or receive a call. I.E. the call connects but I can't hear the caller and they can't hear me. The phone still rings and caller display still works. Likewise I can still place a call in the normal way. Just no audio in either direction. Soft reset sometimes restores normal operation but sometimes a hard reset is required.
The phone was originally on UK Orange network but is now unlocked and running on UK O2.
I got to grips with flashing quickly enough and I have now tried upteen combinations of roms and radios but nothing seems to help.
Has anyone else had this problem ? Or better still managed to cure it ?
Any help or suggestions would be so so so appreciated.
Oh yeah just in case it's relevent.. The phone seems to work perfectly in every other way. wifi, bluetooth, 3G, gps etc. Battery life is a wee bit pants but I'm not too concerned about that.
Thanks in advance guys !
brianbelfast said:
Hello. I've been relentlessly searching everywhere for a solution to my plight.
My Diamond touch works fine for the first few incoming and outgoing calls but then all of a sudden there is no incoming or outgoing audio when I make or receive a call. I.E. the call connects but I can't hear the caller and they can't hear me. The phone still rings and caller display still works. Likewise I can still place a call in the normal way. Just no audio in either direction. Soft reset sometimes restores normal operation but sometimes a hard reset is required.
The phone was originally on UK Orange network but is now unlocked and running on UK O2.
I got to grips with flashing quickly enough and I have now tried upteen combinations of roms and radios but nothing seems to help.
Has anyone else had this problem ? Or better still managed to cure it ?
Any help or suggestions would be so so so appreciated.
Oh yeah just in case it's relevent.. The phone seems to work perfectly in every other way. wifi, bluetooth, 3G, gps etc. Battery life is a wee bit pants but I'm not too concerned about that.
Thanks in advance guys !
Click to expand...
Click to collapse
M8. I don't think you're on your own on this one. I have the same problem ...or similar. My phone pairs OK but drops the blue tooth connection usually on audio but quite often altogether. Re-pairing is a pain in the A$$. It's definitely a phone issue as I have the older qtek and a nokia that work with my kenwood system without a hitch but pair up the diamond and I'm pulling my hair out after 5 minutes.
I've tried the latest stable radio, setting pin code to 0000 & also turning off security but it still drops connection after an outgoing or incoming call.
Does anyone have a fix for this?
...and jetware 1.3 doesn't solve this either. Installed it the other day and pretty much the same ...audio is fine until a call is terminated and then it drops A2DP but sometimes stays connected on telephone. Other times both drop off!
bt stack
In my case it looks like the BT stack on the diamond is not compatible with the Kenwood DNX8220BT stack. I see quotes that HTC implemented their own stack for the Diamond so could someone put me out of my misery and tell me if it's possible to change the stack to something like that on the wizard as that works flawlessly with my Kenwood satnav?
ADD+
My phone does that weird thing too where I couldnt hear the other person on line. I have manage to found a quick fix for it tho.
Solution 1: During the call (when you notice you cant hear the other person), press the middle circle button (which will activate the screen if dimmed out), then press the speaker icon. This allows you to continue the conversation on speaker with the other person on line without having to soft/hard reset.
Solution 2 (works sometimes): During the call, reduce the volumn, wait a secnd or two, then raise it again.
Bt3030 - Shb6100/7100
Have the same problem with Philips shb7100 and shb6100. i also have tried the Jabra BT3030.
I used and test them on a Tyten and wizard no problem at all.
I had same problem before...found out is hardware problem...sent to htc care and after tat everything ok.
ADD+ said:
In my case it looks like the BT stack on the diamond is not compatible with the Kenwood DNX8220BT stack. I see quotes that HTC implemented their own stack for the Diamond so could someone put me out of my misery and tell me if it's possible to change the stack to something like that on the wizard as that works flawlessly with my Kenwood satnav?
ADD+
Click to expand...
Click to collapse
I have the exact same model (kenwood dnx8220bt and XDA ignito (diamond), same problem where everything is okay but when you go into the contacts menu and try to make a call, BT connection either drops or nothing happens when you try to make the call.... this is a joke.... how can my old HTC P3300 work with it without a problem and this newer Diamond flop like a fish...
any updates or news??
I've the same problem. No Sound after some call or others sounds play. When this happens and if I receive a call the others not listen my voice. This means that when audio disappear, speaker and also microphone not work, like the system can't comunicate with them. The volume control not resolve my problem. I've done HR and with nothing installed in my phone the problem come back again after few minutes. So it's not a problem of third part bad software, but htc orginal software or hardware problem.
Anyone solve it o have idea?
Thanks!
I join the list - having problems with my xcarlink which used to work with my P3300
Tried using A2DP Toggle which helped on the artemis but seems to have NO effect at all on Diamond
The Diamond does connect flawlessly to my jabra earpiece and my Sony ericsson bluetooth speaker
ninja_pimp said:
I had same problem before...found out is hardware problem...sent to htc care and after tat everything ok.
Click to expand...
Click to collapse
I have the same problem. Sent my HTC back twice for repair but still no solution. The first time they didn't found the problem, the second time they replaced the speaker.
What did they do with your phone to fix it?
According to this thread http://forum.xda-developers.com/showthread.php?t=431826 it is a hardware issue. The phone needs to go back to the supplier as it is faulty.
What is the silver button on the original handsfree kit meant to do? when i have an incoming call it wont pick up so, so is there meant to be another function to it or something? thanks
i second that also
this key doesn't answer the incoming call
is there someone else has this problem ?
anyone actally used the handsfree kit?
The wired one? I use mine all the time, answers calls here, and a double press makes it dial last number..
hi, i'am also having the same issues.
the silver button does not pick up calls.
has anyone found a solution for this?
I have the same problem
I live at HK
I have been to the Service Center,
But denied it is the handfree fault but the rom bug..
I argued with them, then changed to a new handfree,
but the problem still there....
Hi everybody,
I'm new here and very grateful for all the brilliant solutions you guys come up with to all sorts of issues with x1.
I have the same problem with my hands-free: the button doesn't work and neither does the microphone. Until now, I've thought of it as a simple matter of replacing the hands-free kit, but now I see the suggestion that this is a Rom bug! Will anyone be able to elaborate a bit on this?
thanks and best regards,
Sune
Really not sure it is real or not that is a rom or software bug,
but sure quite a number of problem of people experienced such problem!
I hope SE not to put a death ear on this issue.
It is really annoying as I quite often used the handfree.
hello everyone
the same problem on my russian x1 handsfree. Have tried to fix it with some patches - no results. Then I've bought Nokia Xpress music handsfree, and it works perfectly (and radio works too).
update
VERY SAD, but it doesn't fix the problem. bad quality of X1 jack - thats the problem. Xpress key doesn't answer the incoming call periodically too, but handsfree itself working good all the time
seljean said:
hello everyone
the same problem on my russian x1 handsfree. Have tried to fix it with some patches - no results. Then I've bought Nokia Xpress music handsfree, and it works perfectly (and radio works too).
update
VERY SAD, but it doesn't fix the problem. bad quality of X1 jack - thats the problem. Xpress key doesn't answer the incoming call periodically too, but handsfree itself working good all the time
Click to expand...
Click to collapse
The first time i got to know the headphone dosen;t work in answering call, I really feel astonished. It is such a basic function of phone, how can the genius of SE dose not test it. Do them think we will buy another handfree???
Really disappointed of SE.....
swazpurohit said:
What is the silver button on the original handsfree kit meant to do? when i have an incoming call it wont pick up so, so is there meant to be another function to it or something? thanks
Click to expand...
Click to collapse
Hi I'm Chris from Sri lanka,
Yes, I have the same issue! The handsfree seems to work when I remove it and re insert the jack during an incoming call, but not initially! It is very temeperamental and annoying. I also have a problem when I get an another call when I'm already on a call while using the handsfree. The current call goes to speaker phone and the party cannot hear wht I'm saying through my handsfree!
So I am forced to remove the handsfree and talk during such instances! Crazy this, especially since answering phone calls is one of the core functions of a cell phone! what's the point in having all the frills when answering a call is so tedious!
This is very disppointing, especially with such a high price tag to boot!
same case here. im really disappointed...
i guess that if i can when asus glaxy came out i will change mi xperia for that one... this phone is really "buggy"...
Same probleme here unfortunately.. I tried to remove all
additional programs related to dialing and volume,
switched to the new ROM, but no changes. Button on headset
does not work and microphone neither.
I also have same issue, both HK new stock ROM & cook rom also.
i'm form India, had purchased Xperia X1i and using Airtel network. when i connect my hands free and attend one call the moment second call come, automatically my loud speaker gets activated.
is any facing the same problem in Indai or any where else? will any one help me this.
is there any solutions?
squarecircle said:
Hi I'm Chris from Sri lanka,
Yes, I have the same issue! The handsfree seems to work when I remove it and re insert the jack during an incoming call, but not initially! It is very temeperamental and annoying. I also have a problem when I get an another call when I'm already on a call while using the handsfree. The current call goes to speaker phone and the party cannot hear wht I'm saying through my handsfree!
So I am forced to remove the handsfree and talk during such instances! Crazy this, especially since answering phone calls is one of the core functions of a cell phone! what's the point in having all the frills when answering a call is so tedious!
This is very disppointing, especially with such a high price tag to boot!
Click to expand...
Click to collapse
even i facing the same problem.
is there any solution
The handsfree seems to work when I remove it and re insert the jack during an incoming call, but not initially!
Click to expand...
Click to collapse
Samething here, and the above works for me too (Remove and re insert), but SE really need to fix this for us.
I believe it's a hardware problem, bad 3.5mm jack!
My right earphone's volume has fallen to one tenth. I have it for less than a month. Good listening but bad manufacturing quality.
Personally I don't think it's bad hardware, I think it's bad firmware/rom.
Currently, with GENERIC UK ROM R2AA010, three presses of headset button dials last number, long press disconnects. Not tried incoming call yet.
I really need to be able to customize this buttons function, especially to activate Voice Command, so that I can make calls, play music etc, without the need for touching the phone. Only then, will I be able to make a button for the handlebars on my motorbike.
Want to use a fully wired system to save on battery power, rather than bluetooth. Also, in all the years of using bluetooth, I have yet to find a combination of handset and headset that work seamlessly.
So far, not impressed with the lack of functionality of this headset, but can see why it works like this. Essentially SE should have included Voice Command, then this hardware/software combination would have been shipped working effectively. I think it is merely a cost saving exercise and SE need to provide a patch and fix in their next rom release.