For the past few months I've been flashing separate Energy Roms onto my tilt 2. I finally found one that I liked and stuck with it for the past few weeks, which was the Dinik Glass Energy rom.
Everything was running great until last night when I was watching a video on You tube and everything froze up. I pulled the battery out and turned the phone back on and now it keeps going to the boot loader screen....
I've tried re flashing different roms to see if that would work but I've gotten nothing out of it.
If anyone could let me know of anything that i could possibly do to try and fix this I would be highly appreciative of it.
I dont know what may have caused the problem but in your situation i would have tried to do task29, flash radio and then flash a new ROM. this is normally how i flash my roms but task29 may remove somethin that may be causing the problem. if you have already done so, sorry for wasting 5 secs of your life ... let me know if it worked
Can you show me where I can dl task 29 at?
I had the same thing happen to my tilt2 last week!
Use task 29,
dont freak out when it only shows the screen that says touch pro 2.
Enter into bootloader and run ruu from there, it will fix everything.
Dont flash with sd card in or it will happen again.
I had to clear my sd card and reload it! good luck.
one more thing after task 29 do not disconnect from usb until you load next rom, that is what worked for me best.
hope it helps
I used the RUU and i tried reloading the ROM but it still starts in boot loader screen every time.
Should I just hit the hard reset?
you have nothing to loose by a hard reset at this point ... IF that works.
If I hard reset it will I have to flash a hard spl again?
Ok i noticed that yoy are pritty confused about the terminolog, so here is some help:
1. Task 29 - delets your rom of the phone so your phone become practicly unuseble.
2. HardSpl - "Unocks" (allowes) the phone for flashing custom made roms - i.e. all roms and ro preform Task 29.
3. Hard rest - reinstalls allready flashed rom.
4. Soft reset restart the phone - on/of
5. BOOTLOADER - allowes you to flash without activesync and from Sd card.
When any problem turns on with phene i usually check to see if there is any connection running. I discovered that too much internet over phone makes a phone buggy dissregarding the rom.
You dont have to hardspl phone again, once you did is enough.
Okay well here is the problem then... every time I turn the phone on it goes straight to bootloader. The only button I press to turn the phone on is the main power button. I've ran the custom RUU twice now. I've tried flashing a new rom onto the phone via sd card but it still turns on in bootloader mode. I'm nearly freaking out now because I'm led to believe I've got a bricked piece of $hit.
I hate sounding like a noob but if there is some way someone could run a step by step process to me that works I might through some $$ via pay pal.
Joe Mustard said:
Okay well here is the problem then... every time I turn the phone on it goes straight to bootloader. The only button I press to turn the phone on is the main power button. I've ran the custom RUU twice now. I've tried flashing a new rom onto the phone via sd card but it still turns on in bootloader mode. I'm nearly freaking out now because I'm led to believe I've got a bricked piece of $hit.
I hate sounding like a noob but if there is some way someone could run a step by step process to me that works I might through some $$ via pay pal.
Click to expand...
Click to collapse
I had the same problem with a phone about a month ago. I was able to flash the stock rom and it would boot up then put on the stock SPL and relock the phone. Sometimes I was able to take the battery out and get it to boot but even with the stock ROM I was getting the bootloader at startup. So once I reloaded the stock ROM and relocked it, I returned it and got a replacement.
Sorry, nothing I did every resolved the problem.
good luck.
I agree with taking everything back to stock
flash stock rom
do a spl relock
and start over...
oh, and dont forget about radios! idk if that could be part of the problem tho
I never changed the radio's so I should be good to go then, just the stock rom?
Try this :
- Enter bootloader
- Connect USB cable so "serial" in the bootloader changed to "USB"
- Perform Task29
- Reset
- If the phone enters bootloader skip this step. If not, hold volume down key while resetting (push the reset switch with stylus). The phone will enter bootloader.
- Flash a stock ROM. Download it from HTC website if you don't have one.
- Reboot.
Ow, the stock ROM also contains Radio. So Flashing with stock ROM will flash your radio also.
gabmurillo said:
I had the same problem with a phone about a month ago. I was able to flash the stock rom and it would boot up then put on the stock SPL and relock the phone. Sometimes I was able to take the battery out and get it to boot but even with the stock ROM I was getting the bootloader at startup. So once I reloaded the stock ROM and relocked it, I returned it and got a replacement.
Sorry, nothing I did every resolved the problem.
good luck.
Click to expand...
Click to collapse
When you returned your phone and got a replacement was your phone starting in boot loader?
If so how did the workers at the ATT store react to that so I know what to expect?
shadixs said:
Try this :
- Enter bootloader
- Connect USB cable so "serial" in the bootloader changed to "USB"
- Perform Task29
- Reset
- If the phone enters bootloader skip this step. If not, hold volume down key while resetting (push the reset switch with stylus). The phone will enter bootloader.
- Flash a stock ROM. Download it from HTC website if you don't have one.
- Reboot.
Ow, the stock ROM also contains Radio. So Flashing with stock ROM will flash your radio also.
Click to expand...
Click to collapse
How would you recommend that I flash the stock ROM back on?
I'm kind of confused because I've always flashed with my SD card, how do I do it through my USB? Could you give me a step by step?
Well, those steps I wrote are basically "step-by-step how to flash from usb".
Allow me to clear it:
- Enter bootloader -> Hold volume down button while pushing the reset switch
- Connect USB cable to your computer. and wait until the "serial" word in the bootloader changed to "USB"
- Perform Task29, download task29 and unzip it. run ROMUpdateUtility.exe. Follow the instruction.
- Reset/reboot. well, the phone will reboot itself after task29 is completed
- If the phone enters bootloader skip this step. If not, hold volume down key while resetting (push the reset switch with stylus). The phone will enter bootloader. Connect the usb cable again to your computer (if you disconnect it.) and wait until the word "serial" changed to "usb" again.
- Flash a stock ROM. Download it from HTC website if you don't have one. Just run the exe file you downloaded and follow the wizard.
- Reboot.
I reccomend you to flash with stock ROM because Stock ROMs are "Guaranteed to work(at least by HTC )" and contains radio that may be the cause of your problem. there's no need to flash to stock SPL, yet.
I was stuck in bootloader...
You can find task 29 here. I always do this before flashing.
After task 29, make sure USB is still plugged in and enter bootloader by holding Volume Down key while hitting the reset button. You should see USB on the bottom of the bootloader screen.
Now you should be able to flash the NRG ROM by running the RUU in the same folder as your ROM (rhodium.nbh file).
If this doesn't help, search the entire forum for "stuck in bootloader." I did this and it saved me the hassle of the warranty process.
Before
[/URL]
Joe Mustard said:
Can you show me where I can dl task 29 at?
Click to expand...
Click to collapse
Joe Mustard said:
When you returned your phone and got a replacement was your phone starting in boot loader?
If so how did the workers at the ATT store react to that so I know what to expect?
Click to expand...
Click to collapse
I was able to get it to boot to the ROM by removing the battery several times and reinserting, powering on until it boot. I am on TMobile and called them and they sent me a new phone and returned the old through the mail after expalining the problem. So never went into the store.
good luck.
Related
I have a problem and I've search the forums and search google and I find people with somewhat of the same situation im in... but the methods to fix them don't work.
My problem is,
I have a T-Mobile WING (Herald)
I am flashed on soft SPL with SPL 4.70.Yang
I am ROM flashed to Touch-It WM6.1
I want to flash back to the stock T-Mobile Rom
I run the Stock RUU and it enters the bootloader and at 1% the wing resets
I then get a connection error 260 and the flash will not proceed.
I have tryed restarting my device/computer. unplugging my usb putting in another slot... and still nothing. Any help would be appreciated I'm really unhappy with Touch-It and want to go back to stock and do some customization that way.
you need to extract the .nbh file from the stock rom using 7-zip or winrar on the ruu executable. Make sure you don't extract the spl.nbh file. I think the file you want is something like RUU_signed.nbh
then put it into your HardSPL folder and flash away
Yep. Besides, 4.70.Yang is a HardSPL, not a softspl. If you want the SPL to also return back to stock for warranty issues, then just use USPL along with the tmobile NBH. If not, do what fzzyrn said for the best results.
Got to this thread:http://forum.xda-developers.com/showthread.php?t=421304
Go to post #2 and download the Herald-USPL-beta3
extract the nbh file from your rom and place it in the ruu folder that is located in the flash center folder.
run the utility.
spacemonkey333 said:
Got to this thread:http://forum.xda-developers.com/showthread.php?t=421304
Go to post #2 and download the Herald-USPL-beta3
extract the nbh file from your rom and place it in the ruu folder that is located in the flash center folder.
run the utility.
Click to expand...
Click to collapse
And that links to this.
My T-mobile Dash 620
I HAVE THE SAME PROBLEM . I WAS UPDATIND THE ROM OF MY 620 WITH HTC_S620_WWE_BT_3.66.424.1_4.1.13.44_02.94.90_Ship AND THE PHONE RESTART ADN WHEN THE PROCCESS GOT 25% POP UP A MESSAGE ERROR 260 AND IT WAS RECOMMENDING ME UNPLUG THE USB CABLE AND REMOVE THE BATTERY AND CONNECT IT AGAING SO. I TRIED HARD RESET AND IT DOESNT CONNECT THRU ACTIVESYNC AND ITS STUCK AT THE BOOTLOADER SCREEN (HTC). I TRIED REFLASHING RADIO AND NOTHING WORKS. PLEASE HELP ME. I BROKE MY PHONE.
ROMEROPOLACO said:
I HAVE THE SAME PROBLEM . I WAS UPDATIND THE ROM OF MY 620 WITH HTC_S620_WWE_BT_3.66.424.1_4.1.13.44_02.94.90_Ship AND THE PHONE RESTART ADN WHEN THE PROCCESS GOT 25% POP UP A MESSAGE ERROR 260 AND IT WAS RECOMMENDING ME UNPLUG THE USB CABLE AND REMOVE THE BATTERY AND CONNECT IT AGAING SO. I TRIED HARD RESET AND IT DOESNT CONNECT THRU ACTIVESYNC AND ITS STUCK AT THE BOOTLOADER SCREEN (HTC). I TRIED REFLASHING RADIO AND NOTHING WORKS. PLEASE HELP ME. I BROKE MY PHONE.
Click to expand...
Click to collapse
The S620 is not a herald and every phone is different, so I'm not sure if we could help you out. Does your phone have a HardSPL? Have you used HardSPL before? Even if the activesync icon doesn't start trying to sync it doesn't mean that it's not connected, it just means that it has nothing to sync (since it's in bootloader mode.)
I FIXED
I Did These Steps:
I Turned My Phone Off
I Pressed The Camera Icon Button
I Turned The Phone On (no Loose The Camera Button)
It Got Into Boot Mode
I Plugged To The Usb Cable
I Oppenned The Ruu For My Phone Version
And Wowla Fixed
Thank You Guys For Your Help
The Answer is in a Careful Search
This post is being made to you about... a month too late. But that's because I just got the Wing yesterday and started trying out roms today. Anyway, ran into the same problem earlier today and found the answer in the forums. I've written the following for those who might need all the steps. In your case, read from step 3. Anyway, in case you still have this problem, here's what you do:
1. Hold camera button when pressing the soft reset to get into the bootloader; it should be in red blue green and white. something like that.
2. Connect the usb to the computer and run the stock RUU Utility (this can be found on the official t-mobile website. look under something like support/downloads for the Tmobile Wing)
3. When it hits the 1%, the phone will automatically restart. When it does this, it breaks the connection between the computer and the phone. At that instant, hold the camera button and the soft reset button. Then, when you let go of the reset button, it should go back to boot loader.
4. At this point, the Rom Utility should give you the error. Do not take out the battery as instructed. Just disconnect the usb, reconnect the usb, wait for the computer to recognize it (it should appear in my computer) and then just continue the utility.
Good luck. =)
i had the same problem flashing my P4350 yesterday. tried a lot of different things, the solution for me was:
1. start flashing from the bootloader
2. just to hold the camera button when the phone restarted after 1% (nothing else, no soft reset or anything).
this resulted in the phone restarting in bootloader again, and after that it just resumed upgrading the rom.
koekiemonster said:
i had the same problem flashing my P4350 yesterday. tried a lot of different things, the solution for me was:
1. start flashing from the bootloader
2. just to hold the camera button when the phone restarted after 1% (nothing else, no soft reset or anything).
this resulted in the phone restarting in bootloader again, and after that it just resumed upgrading the rom.
Click to expand...
Click to collapse
This one works for me. Thx!
hi people.
hopefully 1 of you guys can help.
i flashed a dutty rom on my blackstone a while ago, and everything went fine. then a month or so later, for no reason, my fone just shuts off, 5 or 6 times a day. so i decided to flash the original software to see if its a hardware prob and then hopefully get the fone replaced.
the only problem is i managed to sync my fone ONCE since i put dutty's rom on and never since then. even in boot loader the fone only ever says "serial" and never, ever usb. i've tried different leads, different pc's, and these leads and pc's will connect to my old trinity which still flashes a dream!
so i reckon there must be some connection prob in the blackstone itself. any thoughts?
i read somewhere that you can flash from the memory card. so i got a rom, and copied it to the root of the card, then started in bootloader. it flashed up a grey screen with some writing on, then straight to the bootloader screen so fast, i never got chance to read what it said. did i not get something right?
the rom is titled "BLACIMG.nbh" on the card
thx in advance
two_bus said:
hi people.
hopefully 1 of you guys can help.
i flashed a dutty rom on my blackstone a while ago, and everything went fine. then a month or so later, for no reason, my fone just shuts off, 5 or 6 times a day. so i decided to flash the original software to see if its a hardware prob and then hopefully get the fone replaced.
the only problem is i managed to sync my fone ONCE since i put dutty's rom on and never since then. even in boot loader the fone only ever says "serial" and never, ever usb. i've tried different leads, different pc's, and these leads and pc's will connect to my old trinity which still flashes a dream!
so i reckon there must be some connection prob in the blackstone itself. any thoughts?
i read somewhere that you can flash from the memory card. so i got a rom, and copied it to the root of the card, then started in bootloader. it flashed up a grey screen with some writing on, then straight to the bootloader screen so fast, i never got chance to read what it said. did i not get something right?
the rom is titled "BLACIMG.nbh" on the card
thx in advance
Click to expand...
Click to collapse
First off all Flashing queries should be posted in this thread.
To answer your question.......If you are only getting 'serial' at bottom of bootloader I'd recommend flashing original stock rom which came with your device first before trying to flash a cooked rom. This original stock rom can be flashed even if it states 'serial' in bootloader (note - this is the only rom this will work with). Stock roms can be found here. Once you have flashed this stock rom, use this guide to flash rom
For your info, flashing from sd card should be done as follows:
Copy BLACIMG.nbh into the root dir of your Storage Card.
Be sure to have at least 30% of charge.
Turn off your device by using the Power Button
If you use HardSPL: Go to bootloader mode. Push and hold Vol Down + press Power button. The device will display a message and offer you to flash.
If you use USPL: Remove your microSD card first to prevent starting the flash, then go into bootloader mode. When in bootloader mode insert the card and follow the instructions on the USPL page to start USPL. The device will restart into USPL and will now present you the message to flash.
As soon as presented the message, push Power button to start flashing or Volume Down button to cancel.
The whole procedure will take about 3 minutes. After you finish and see the relative message, soft reset your device, you are ready.
Please post further flashing queries in dummies guide thread
Thread closed
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
I recently synced my HD after having flashed the EVO Grid 1.8 ROM.
Since it took over half an hour I disconnected the phone from the computer during the sync process. Now the screen freezes as soon as the smart mobility screen shows up. I soft reset' the phone as well as I tried hard resets. Still the phone doesn't go beyond the smart mobility screen and freezes.Is there another option to get the phone back apart from resetting it? Or is it completely bricked now. I've always successfully flashed the roms, so it can't be connected to a wrong ROM flash.Thank you for a feedback.
What you can try is place an ROM on your memory card (BLACIMG.nbn) and flash it. (shut down phone, hold vol down and power up).
Maybe this will do the trick. Good luck
Can you still get the phone into bootloader mode (tricolor screen)? It's likely you can - then just re-flash the rom (although to be safe I'd download it again).
Did you follow this guide to initally flash rom? If not, I'd suggest you do. As pointed out above, if you can still get into bootloader your device is not bricked. Just follow guide and reflash rom
just do like "jontelfer" said go to 'bootloader' for getting 'Tricolor' by pressing 'Volume Down' and 'Power' 1 time. Then u can see 'tricolor' and re-flash what ever rom you want.
I had try 'Xannytech ROM Grid Leo 2.5 (Internal Rel. 4.2.5.202)' and found the same as your problem 2 times already.
Now I'd change to test others.
I would be tempted to flash it back to original SPL and ROM and then start again from scratch. This happened to me a few months back, I couldnt flash any cooked ROMS at all until I reverted back to stock and started again.
Yeah and do not forget to hard reset after flashing. It can sound useless but it really helped me when I got some problems with some roms...
- Bya -
Thanks everyone. I flashed to a different ROM and it's working again now.
It's tougher than I thought to find an innovative, graphically sophisticated and most of all stable ROM.
good to hear had this ones before and gladly figured out how to go back and flashed it again with a stable rom!!
I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.
xgenvn said:
I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.
Click to expand...
Click to collapse
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??
circleofomega said:
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??
Click to expand...
Click to collapse
As i pay attention to the bootloader, i'm sure that it's already made the HardSPL and the phone can recognize the image on the SD Card or by USB method. The first ROM was flash on the phone is not me, this is my friend's phone, I'm just trying to help him around then.
I tried to flash the rom by USB method, but when i restarted the phone without the USB connected to PC, it did show the bootloader (i just touch the power button, not volumn button or any other key)~ then i plug USB which connect the phone to pc, soft reset it and it boot to the system again.
I try to flash it by SD-card method but it still the same. I mean that the phone can be flashed new ROM, but it's just keeping get into the bootloader everytime i restart the phone
If the image is on the SD Card it'll tell me to upgrade ROM, if the image is not on the SD Card then "No Image File!" was flashed on~
Any ideas? My friend tells me that this happened when he tried to install Sogou - chinese input application. Is there any conflicted that cause this matter?
for little detail, the phone always shows up Successfully, but it still enter the bootloader mode at next restart. Is my flash-job done or just a mistake one?
additionally, this may be bad... remove the battery doesnt work. Please help.
help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?
xgenvn said:
help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?
Click to expand...
Click to collapse
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.
D-jack said:
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.
Click to expand...
Click to collapse
I've just tried out the task29, it's done normally, then flash the new rom.
1. I dont think the rom are buggy, because i changed between 2 roms and it's the same matter.
2. I dont need to use bootloader/rom update combo button because it's directly entered whenever i turn on the phone (without connected to pc) (i really really dont know why)
3. Hard reset and i have my WM work again but it's still the romupdate at boot time.
I wonder if jumpSPL did all this problems, I tried mtty by task 0 and set 14 0 but it wont restart the phone, tried to format the ROM by mtty (task 32) but it wont weep out, errors given: bad... at address...
Why does it always want me to update the ROM? Is there anything wrong with jumpSPL?
the problem still, please help me give a look to this.
ouch, last time I use mttty were ancient wm2003 era. i'll try to look for info, but can't promised anything.
at this point it's recommended to reflash the complete original stock rom, undo hardspl.
check the hardspl thread about restoring to factory default. best luck to you.