Related
I will soon be opening up my phone (T-mobile Pocket PC Phone Edition) to replace the glass screen with a new one ordered online. I've never even opened the phone before and was wondering if someone has performed this operation before. I would really appreciate any pointers, tricks, cautions, pictures, etc.
Thanks.
lawrence... where did u get the replacement??
i wonder if they got replacement cases! i chiped mine
The company I bought the screen from was GetHighTech, Inc, in California. By coincidence, they are about an hour's drive away from my home.
They only sell the glass screen and high capacity battery replacements. The screen comes with absolutely no documentation or instructions. I just got it a few minutes ago.
just wanted to see if you had any luck with the changeout.
Screen replaced successfully: observations
It was a tricky operation, but I finally managed to replace my broken touch screen. And the patient is alive, and only a little worse off for the experience.
I was held back for a week until I could get the right size torx screwdrivers to remove the back cover. Once inside, it was a very very tricky process slicing off the broken screen with a razor blade. It was glued to the lcd display. This would have been hard even if the screen was not shattered. Definitely needed goggles to protect against flying splinters of glass. I used cotton swabs and 99% alcohol to clean the glass dust off the glue around the edges of the lcd, then I put the new screen on while that residual gum was still a bit tacky.
There was a very thin existing plastic cover over the lcd in between the glass touch screen and the rest of the lcd. Since it did not come off with the glass, I left it in place even though it had a couple of small scratches from contact with the broken glass. It seems like it was there to keep dust off the lcd or something like that.
This was my first time inside the phone. I noticed that replacing the whole LCD component would have been a trivial task by comparision to replacing the glass alone. And even easier would have been adding a new battery.
cracked lcd on xda
hi, does anybody know where i can get a replacement for the lcd screen on my xda... its totally mashed and i need to unlock it but the screen is bad...
i live in uk... any ideas guys..
pls help out
has anyone give me pls an idea how much a new replacement screen for XDA might cost
currently I am having two XDA (one XDA and one MDA), MDA has a broken screen ... I'd like to know how much is the material (screen), I have so. to do the actual job of screen replacement
regards, monika
I replaced my touchscreen a few weeks ago. Like Lawrence said it's a little tricky and you need to be patient.
I bought my touchscreen from www.pdasmart.com/pdaphone.htm for $75 and they gave great instructions.
thank you for your kind answer
hmmm, seems like it is nice to live in US ... where all the things for XDA are almost readily available :wink:
regards, monika
Protective Acryclic Cover over the Digitizer
I have an odd problem. I have an SX56 with a broken protective cover. The protective cover is the acrylic sheet that sits between the digitizer and the outside world. Everything else works fine including the digitizer. I have found every replacement part except that cover. I've even tried local plastic stores. They don't carry the proper thickness (0.125mm).
Any thoughts or sources besides sending it in for a $200 repair?
heey fellow forum readers,
i hace got a oil stain under my screen
can somone tell me what it can be?
thnxs fore the info
Hello my friend.
Well actually that is very bad news. If you are inside the guarantee go to your dealer because this is a hardware and manufacture problem. Its a common problem on the latest hi res touch screens for htc.
I have the HTC touch diamond and i have the "Oily square of death" which is a like a rectangle just in the middle of the screen which looks like oil. My be your screen has become less responsive, some are reporting that with the time the screen goes completly useless and does not work at all.
There is no way you can fix it by yourself. I know its hard to know, still is a common problem So sad my friend.
Regards-
Bad situation. Sorry to hear that.
I dropped my TD2 to the ground today and i was very scared. I hope its okay.
this is caused by too much pressure on the screen by for example carrying the phone in your pocket and sitting down. i had the same problem and abviously the screen lowered itself into the phonecase. have a look on the phone sidewards and i think you will notice the same. i had luck and had an guarantee exchange. but normaly htc does not cover screen problems! take care with that phone.. even the manual says.. dont carry it in the pocket and sit down.. which is quite ridicolous for a mobile phone isnt it?
I had a dust particle under the touch screen (between the touch screen and display).
I've took the phone to my designated service (which was not an original HTC service) and they've cleaned it up. Now it's ok.
Maybe you should do the same.
thnxs
thnxs fore the reactions
i have contacted my phoneshop
the said it is a commen problem and it wil be cofferd
thnxs fore al the tips and help
Hmmm... I have the smae on my T-Mo Compact V.. wonder if they will cover it?
POSSIBLE SOLUTION!!!!
I fixed the very problem you guys are having with duct tape. Yes duct tape. The problem is not that the layers are separated, but that they are stuck together. So basically, your phone is acting as if it's continually being pressed, I put duct tape on the screen and gently removed it. I had to do this about twenty times, but eventually it separated the layers and the phone works like new. I know it sounds crazy, but it worked. I am aware of one other person who has had success with this method. I saw him post it on another forum. I believe this method will work for many of you so please try it and please be patient. As I said, it took several adhesions and removals before it worked.
momojopoe said:
POSSIBLE SOLUTION!!!!
I fixed the very problem you guys are having with duct tape. Yes duct tape. The problem is not that the layers are separated, but that they are stuck together. So basically, your phone is acting as if it's continually being pressed, I put duct tape on the screen and gently removed it. I had to do this about twenty times, but eventually it separated the layers and the phone works like new. I know it sounds crazy, but it worked. I am aware of one other person who has had success with this method. I saw him post it on another forum. I believe this method will work for many of you so please try it and please be patient. As I said, it took several adhesions and removals before it worked.
Click to expand...
Click to collapse
hehe nice...
if you cannot fix it with ducktape it is because You are not using much of it!
ducktape - a mans best friend!
reminds me of a time when we hooked up a projector with ductape during a conference
tape everywhere!
Tape works!!!
LOL
Last week I bought an Diamond 2 because the digitizer of my Cruise stoped responding. I tried the tape thing and... my cruise is working as a charme again.
Were there is duct tape there is hope
Wtf???Who came up with this????F***** awsome!!!The screen finally responded but seeing using a direct light there's still a square...Replacing a digitizer should sholve the problem,huh?
It hapend for me to this morning but the screen was still responsive.
Then I did the quick tape reperation and now whola rings are gone
hi
i think this tape sollution should be a sticky
had a go at the duct tape as a bit of a last ditch attempt.
still no luck, the oil stain disappeared however the screen remained mostly unresponsive.
a bit of screen mashing will press certain things in certain places, but not where the initial pressure was applied.
might keep trying it later.
word of warning though, careful if the sticky tape is strong, my digitiser started separating a little. i've resigned myself to a new one anyway so it wasnt much of a loss for me if ive made it worse.
just an fyi
Hi ,
anyone found a detailed guide on how to change the digitizer?
Tilt 2 Screen doing this.
OMG My Tilt 2 has the huge oil stain square thing now. Never had this before. First time I had it in my pants pocket ever without its case... 1 time. ATT says that I damaged the screen. By having it in my POCKET? WTF. This sucks. Ill try the Duct Tape thing. I hope that works.
IMO you can't expect a digitizer to withstand constant, direct pressure such as that inside of a tight jeans pocket. After all, it's just a few sheets of plastic with tiny gaps in between.
The digitizers employed on the TD2 and some other, newer models seem to be particularly sensitive, but nonetheless this is a common hazard with ANY resistive touchscreen. The plastic in a resistive touchscreen has to be soft and bendable, and because of that it is also susceptible to warping.
Capacitive touchscreens can be fitted with tough screen surfaces thanks to the relevant touchscreen components sitting behind the display panel and not in front of it.
I've used a hardcase with screen cover for the past six months since I bought my TD2. It makes the screen somewhat inaccessible on-the-go, so it's not the most practical solution. Still, it's the only way to truly protect the screen from pressure.
http://www.pdair.com/catalog/product_info.php?cPath=10100000_900000_11000630&products_id=17582
sorry to dig out this post...
I have the same problem, I am planning to send it back to HTC. Do you think there is a risk they don't take it within the guarantee (sorry for my bad english) as I installed hard SPL and a cooked rom ? Maybe should I reinstall official HTC rom...
thank you for your advise
So here's the deal. My screen bezel began to loosen a bit, so I restored the phone and took it into the sprint store to get it replaced through insurance. They proceeded to tell me that having the screen bezel clips break was a "cosmetic problem" and that would not be covered by insurance. If you don't know what I am talking about, there is a gap between the chrome bar and the gray plastic on the side of the phone. It is big enough to see the backlight from the screen, and I repeat "cosmetic". The tech decided it would be a good idea to just crank the torx screws as tight as can be, yet that didn't solve the issue. Anyone have any ideas on how I can actually get a replacement phone? The guy made a note on the account that I was having that problem so that he could notify me of another returned hero with a decent top, so I don't think going to another store will work.
Any common problems? Can overclock till meltdown?
So I like just about everything about the Sony Z compact line of phones but durability wise I have been unlucky. My first Z3 compact died from water damage and my 2nd one has a screen that is ready to fall off the device.
I choose to buy a HTC U11 to replace my Z3 compact as I have never owned a HTC phone before and thought I would try something different.
What I would like to ask here though is it worth trying to fix the Z3 compact to sell or not?
The only way to protect this phone:
The phone bends 0.1mm causes the phone screen to start opening. So it's not suitable for jeans pockets.
I remedied this by using an anodized aluminium bumper and tempered glass both sides.
Sony does a very bad repair of it's phones, and the issues will return, and their parts are expensive.
It is better to do it yourself and use B7000 glue, use plenty, easily removable for future repairs, no heat, clothes pegs, wait 48 hours before removing pegs or turning on the phone. And look for the best grade of screen with frame, Sony uses two manufacturers for its screens.
My Z3C has a screen that is lifting. This thread and others seem to indicate that fixing the screen is not hard but hardware is not my thing at all...
Would a phone repair place (in a shopping centre) be able to do this kind of repair? Is the phone much different to other phones that people would take in for screen replacements?
I don't care about the loss of waterproofing. The screen isn't even falling out, just lifted in the corner. I don't want to send the phone anywhere and be without it, or have it come back changed in unexpected ways...
a1291762 said:
My Z3C has a screen that is lifting. This thread and others seem to indicate that fixing the screen is not hard but hardware is not my thing at all...
Would a phone repair place (in a shopping centre) be able to do this kind of repair? Is the phone much different to other phones that people would take in for screen replacements?
I don't care about the loss of waterproofing. The screen isn't even falling out, just lifted in the corner. I don't want to send the phone anywhere and be without it, or have it come back changed in unexpected ways...
Click to expand...
Click to collapse
Phone shops including Sony themselves have difficulty in repairing this particular phone, I think any phone shop can do this repair, but, they must use the B7000 glue or similar, or silicone, and not the red tape they usually use, it's useless, as this phone can heat up, or the blue z3c ready cut tape is not so good either. And if you get the wrong screen (clone), the colours will not be as good.
Many phone repairers have the clone screens that are thicker than the original.
The screen sometimes is actually bent, along with the body, check on a flat surface.
Always buy a good screen together attached with the body, and never by itself.
So armed with this knowledge and or hardware, you could go talk with a phone repairer... The first 3 times, shop, but maybe the fourth repair, try doing it yourself, it's as easy as opening a PC, just smaller, just follow z3c repair guides and youtube, when you're ready. When attempting to repair the phone, for the very first time, do it over hours, maybe over the weekend, and not one sitting.
If you start loosing patience, leave it for a while etc.
[emoji12]
I got so comfortable with opening my phone, I put extra 0.3mm copper plates on the processor and gpu with Cooler Master Extreme Fusion paste etc. Lol.
But it's good to have an already damaged motherboard to work on.
Z3C LOS Omni Oreo
My screen is still working fine. Just lifting.
I do have some old phones I could practice on, assuming they have the same glass sandwich construction.
I will go look for some videos...
a1291762 said:
My screen is still working fine. Just lifting.
I do have some old phones I could practice on, assuming they have the same glass sandwich construction.
I will go look for some videos...
Click to expand...
Click to collapse
?
Z3C LOS Omni Oreo
I put up with my screen for a long time but eventually the glue gave out and I had no choice. It was good, then bad, but ultimately ok.
I didn't have any trouble taking the glass off the first time because the glue was barely hanging on. I had a look and noticed that the headphone jack's glue was also failing. Probably why it was becoming unreliable. I glued that and reseated the screen cable and it worked fine while sitting there so I glued everything on again.
It was a poor first attempt. I had both too much glue (blobs that leaked out) and not enough to actually seal around much of the screen. No problem. I took the glass off again and glued it again. This time I followed the instructions closer and glued the front screen before connecting the ribbon.
The second gluing was good but something with the ribbon was wrong because it only worked when I pressed on the lower part of the screen. Sigh.
Taking the glass off after a good glue was much harder. I finally got the spudger under the glass but I moved it sideways before removing the suction thing. It was too much pressure for the glass. The good news is that it was the rear glass and only the bottom half shattered. I got the rest off and started on the front.
Now that I knew to be more careful, I got the front off OK. Reseat. Test and working. I glued the front on first again, without disconnecting the cable. Tested and working. I glued the half back I had on (covers the camera).
Its working!
I use a case so the back isn't even a problem, but I ordered a new back from China (cheap). The headphone Jack seems better. I put a new screen protector on. In some ways the phone is rejuvenated.
I was apparently not careful enough when taking off the screen though. I appear to have some marks on my screen now. It's minor, probably won't notice during normal use, but there if you look.
I'm so glad to have my phone back. I've been using an iPhone for the last 3 weeks.
Thanks for the tips.
Edit: The hands free speaker works again too. Bonus
So I have noticed a "black" dot near the right edge about halfway down on my screen. I can feel what may be a scratch but definitely not a deep one. When I first saw it, I had a screen protector on it and thought a piece of dirt had gotten in between the screen protector and the screen but after I took it off I noticed this dot. Anyone had this problem. I would like to think Samsung would help me but my back glass has spider cracked and I'm not sure if they would still honor this. Anyways here's a few pictures, tell me what you think.
It is not ONE dead pixel, it is a group of pixels, most likely due to an impact, only fix would be screen replacement, sorry
Stunna4life888 said:
So I have noticed a "black" dot near the right edge about halfway down on my screen. I can feel what may be a scratch but definitely not a deep one. When I first saw it, I had a screen protector on it and thought a piece of dirt had gotten in between the screen protector and the screen but after I took it off I noticed this dot. Anyone had this problem. I would like to think Samsung would help me but my back glass has spider cracked and I'm not sure if they would still honor this. Anyways here's a few pictures, tell me what you think.
Click to expand...
Click to collapse
I had one little dead pixel, samsung replaced whole screen and battery
Well, that 'scratch' that was made is basically a drop to your phone.
Whatever it is that the phone fell on managed to poke into the OLED screen, probably missing the digitizer by a little, damaging that cluster (the shape and shading of that makes this make sense)