Phone is Dead - A warning for others. - Galaxy S I9000 Q&A, Help & Troubleshooting

Ok, heres the deal.
My girlfriend has the same Galaxy S as i do, and i wanted to go back to stock.
Id grabbed all the needed files off her galaxy (boot.bin, cache.rfs, dbdata.rfs, factory.rfs, modem.bin, param.lfs, sbl.bin and zImage) and loaded up heimdall to flash them all back.
The flash finished successfully, the phone switched off, and i awaited a reboot.
It never came.
The phone is now in a Non- Functional state, wont turn on at all.
The battery was fully charged at the time, and ive also pulled her battery out and tried it, but still no go.
Im thinking something inside is fried.
Just thought id share my misfortune with you, just in case someone else was going to try the same thing.
If you were gonna try....think twice
So i guess its back to Optus shop on tuesday, and see what i can do about a replacement.
Cheers all.

you shouldn't use boot.bin ,Sbl.bin and param.lfs. It is not safe to play around these files, you could dump other files and flash it,without any problem,

Ok, well maybe thats what has killed it.
Ive tried all key combinations, but nothing at all.
Pretty convinced its fried.

OzzYGuY said:
Ok, well maybe thats what has killed it.
Ive tried all key combinations, but nothing at all.
Pretty convinced its fried.
Click to expand...
Click to collapse
I did the same thing on my phone and happened so, but I took it to service center and they repaired without changing the board or opening it(this is what I think because there were no trace of any physical repair), anyhow its working again. but before you may try some methods which I read in some forum as below:
Remove everything from your phone (SD card, sim, battery).
Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
Press and HOLD vol. up and vol. down.
As you are HOLDING these buttons, reattach your battery.
You should be in Download Mode.
there is another method which I will try to find and inform you

Thanks for the tip....but no go.
Screen still black....
Its like its not getting power at all.

Try and force it in to download mode [vol down - home key - power button] and then reflash it with a stock rom. If that fails then you could try holding just the power button in for a minute or 2 but if that also fails then your last option is to try and either get hold of a jig or make one to try and get it in to download mode.

Using the application Odin should fix this problem. as above said, about vol up vol down, im sure it is volume down,powerbutton and homekey when connecting to a comp when odin is open. Odin is ure failsafe. correct me if i am wrong with this information!
jonnyb

sean2476 said:
Try and force it in to download mode [vol down - home key - power button] and then reflash it with a stock rom. If that fails then you could try holding just the power button in for a minute or 2 but if that also fails then your last option is to try and either get hold of a jig or make one to try and get it in to download mode.
Click to expand...
Click to collapse
Ive tried all key combinations that we know.
Ive flashed it many times before, but i think this time after the flash, something has blown, in between the battery, and the power switch, so its not getting any power.
I think the only cure is to return to samsung for repair.
Ive tried everything that ive read from various google searches for the last 8 hours or so...and no hope.
Im almost positive theres no power getting from battery to the power switch.

Phone is Dead - A warning for others.
Yes follow instructions understand what you are doing first dont make it up as you go along .
I would guess you have destroyed boot loader .
Possible fix is download mode recovery jig .
Samsung service centre possible charge .
jje

Grabbing some resistors tomorrow, will see how that goes.

JJEgan said:
I would guess you have destroyed boot loader .
Possible fix is download mode recovery jig .
Samsung service centre possible charge .
Click to expand...
Click to collapse
If the Sbl.bin id non functional, the Jig can't do anything, you must use a RiffBox or equivalent sadly.

sad story, hope never will happen to me

If its still under warranty just go to samsung service centre and tel them you tried upgrading firm ware over the kies and phone did not boot after that. Its not easy for samsung to find what you did with the phone. they will replace mobo free if warranty is valid.
Sent from my GT-I9003 using XDA App

trip007in said:
If its still under warranty just go to samsung service centre and tel them you tried upgrading firm ware over the kies and phone did not boot after that. Its not easy for samsung to find what you did with the phone. they will replace mobo free if warranty is valid.
Sent from my GT-I9003 using XDA App
Click to expand...
Click to collapse
Yeah will do.
Mrs will take the phone in to where she bought it on tuesday, and see what the process is.
Phone still under warranty so i doubt ill have any worries getting it repaired.
Bought a jig this morning for $8.00.
Knew it wouldnt get my phone goin after reading that if the secondary boot loader was not intact that it wouldnt work. As id flashed the sbl.bin i knew it was toasted, but for 8.00, having a jig handy is worth every cent anyhow.
Have my Galaxy Tab to use as a phone untill the "S" is repaired, so thats a bonus.
Although im without a phone for possibly 2 weeks or so, i dont regret flashing it.
Its a good learning curve, and one ill remember.
At least i know now, that even though heimdal has slots for the bootloaders, DONT USE THEM
Its all good, and im not discouraged in any way from flashing it again as soon as its repaired lol.
All in all its been a good lesson learned.
Ive learned about the download jig, which of was unaware of earlier.
Thanks to all those who replied with info....i do appreciate it.
Will post back results of the phone return....when i know more.
Cheers

Thats the spirirt dude. I was in the same situation as yours. Got my motherboard replaced under warranty period, they took 2 weeks but were quite helpful. I said kies update bricked my phone. They replaced it for me. All happened within 2 weeks of the phone purchase. so it was bit tenseful situation. I own I9003.

Got my Galaxy back yesterday.
Turns out the main board was fried.
They replaced the board...and am now functional again...
Its the stock DTJP3 firmware.....but not for long LOL
Think ill leave heimdalls boot options blank from now on...better still, ill use Odin instead.

OzzYGuY said:
Got my Galaxy back yesterday.
Turns out the main board was fried.
They replaced the board...and am now functional again...
Its the stock DTJP3 firmware.....but not for long LOL
Think ill leave heimdalls boot options blank from now on...better still, ill use Odin instead.
Click to expand...
Click to collapse
hey..i have the same problem..going to svc tmmr...how long did it take?

Related

HELP: I accidently installed a Sam. CAPTIVATE rom on a Galaxy S i9000- Not booting up

PLEASE HELP: Calling all experts!!!
After installing the: [STOCK ROM] Odin3 One-Click Downloader and Drivers CAPTIVATE ONLY
My Galaxy S 19000 is stuck on the at&t boot screen.. the at&t logo just keeps flashing...
I cannot get into download mode...
PC is not recognising phone via Kies, odin or anything else...
Something tells me I have made a huge mistake somewhere along the line.. any fix???
Thank you
If no recovery/download mode working...
Only UART/JTAG, check on progress on this.
Thank you for your help...
Quite expensive options aren't these, GOOD THING I HAVE INSURANCE!!!
There must be a software way around this thou...
HELP!!!!
If your phone can't get into download mode due to it being disabled it looks like your pretty much screwed. You could phone samsung and see if they'd fix it.
Sent from my GT-I9000 using XDA App
If you can get to the AT&T logo part, I'm assuming you should still be able to get to download mode. Did your phone have dl mode before?
Thread moved to Q&A section
Yes my phone could get into dl mode b4 but now it doesn't work any more, phone just keeps on showing at&t logo and rebooting.
When I put the USB lead in the phone does not switch on at all..
thanks 2 all for assistance in this horrible mess negligence has left me in.
the USA models goes into download mode by using the volume up + volume down + power
see if that works
Thanks for your reply...
no joy... any other viable button combinations I could try? I've already tried many to no avail...
I'm no expert on the matter but don't you think that since you flashed a Captivate ROM on an I9000 that the home button wouldn't work since the Captivate doesn't share the same home button? Logically I would try looking for what the combo is for the Captivate to get into download or recovery mode. Now, I may be wrong and it may not work if the captivate uses its home button to enter the home button but it's worth a shot.
Edit: I just checked here and it says you hold both the volume up and volume down button while you press the power button. Try that.
With the device off, try holding both vol + & - then plugging in usb cable. Thats how a captivate enters download mode. If flashing the i9000 on captivate changes the button sequence it could not hurt to try.
Sent from my SAMSUNG-SGH-I897 using XDA App
@ Bell & foom....
I understand both your thought pattern and YES this was mine also...
However thus far no combinations have worked, still continually looping the at&t logo.
If I plug in the charger or USB whilst its doing this it kills the device, it wont switch on...
Knowing the different CAPTIVATE button comb. to recovery or download mode would be a big help right now.. also how the buttons would be mapped... i.e Captivate rom. on GALAXY S device?
How would one fix a captivate that was continually re-booting at operator logo start-up? Might be another way to angle this?
Thanks....
Think u are better off paying the guys at samsung or phone repair store to load the right firmware back in if u dont have the 3 btn combo...
Sent from my GT-I9000 using XDA App
try downloading that one click unroot program, plug the sgs into the computer and then force unroot, although the unroot won't work it should then allow the sgs to enter recovery mode.
Unfortunately my PC is not recognising the phone...
Plugging the USB in while the phone is switched OFF does nothing....
lugging the USB in while the phone is switched ON.. Turns it off...
Same things happen when the Charger is plugged in.. Althou the phone seems to still charge!!!
Arghhh..
Thanks for your suggestion thou.. Any more help/ ideas are welcomed...
Last resort maybe try heating up the phone like the others did to force download mode?
Sent from my GT-I9000 using XDA App
so any news on this? i too have successfully flashed the captivate rom on my unbranded i9000 the official repair shop i first took it to (mttc <Lithuania>) told me that it needs a new motherboard, and it would cost me 700LTL(270 $us)... kinda sounded like bull****, so a week ago i took it to a private repair shop, they said they had jtag, so i should be hearing from them this week, if not, i'll buy the stupid riff box myself and repair it..
no button combination worked for me, and the symptoms were exactly the same, flashing att, usb kills it etc. etc.
well, my advice would be to keep contacting different local repair shops, and asking do they have a jtag that supports the samsung galaxy s, if they do, the repair shouldn't cost more than 25$, at least thats what I've been told. good luck, and stay in touch, update on your process, cause the number of people flashing the wrong rom on the i9000 is horrifying.
it kinda sux that its so easy to brick the sgs... and its wrong for people to state that "if you have 3button combo enabled, you are safe", well thats just bull****.
No GOOD news as of yet, but I am in the process of to admitting my SGS to a official samsung service centre.. I was also thinking of sending it directly to them for repair...
???
Still been trying some other things to try and jump-start this blasted thing in the meantime but NOTHING IS WORKING!!!!
I to am thinking about purchasing this riff box or JTAG but it would be for a ONE TIME USE only... Seems like a waste of money when I can just claim a new SGS through insurance only thing is playing the WAITING GAME!!!
I Shall definitely update this thread with any progress made in the coming days...
Here I was thinking I was a lone soldier with this dilemma...
Also I agree... SGS = Too easily bricked.. and no solution?? Other than splashing out 100+ £/$... in your words truly SUXXXXXXX!!!!
Konshens said:
Also I agree... SGS = Too easily bricked.. and no solution??
Click to expand...
Click to collapse
Sorry, but ANY phone (or even any electronic component for that matter) is easily bricked if you flash firmware from a completely different device onto it.
Electroz said:
Sorry, but ANY phone (or even any electronic component for that matter) is easily bricked if you flash firmware from a completely different device onto it.
Click to expand...
Click to collapse
well, afaik, its very hard to fully brick a new htc device.
anyway, i suggest you try finding a jtag repair shop first, as samsung will take a lot of time to "repair" it, or even tell you that it needs a new motherboard..

Disconnected from PC in the middle of Odin restore-phone wont' boot.

The USB cord was removed from my phone in the middle of an Odin restore (it was stuck at factoryfs.rfs). Now the phone won't boot and it isn't recognized by my computer when plugged in. Did I find a way to brick this thing? Any help would be appreciated. This is my fourth Captivate and I'm sure AT&T is going to start to give me a hard time. Thanks.
build a jig or buy one on ebay. you need to get into download mode and reflash to sotck.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
http://forum.xda-developers.com/showthread.php?t=731989
Try all 3 methods to get into download mode first
yes, you can try the key combo first. but as i know, build 1010 or later wont work for the key combo.
Got it back to d/l mode. Now it's stuck at factoryfs.rfs-same as last time. I'm finished with this phone. AT&T can send me another. This is what happened to the past two phones. Stuck on a Odin restore and can't get it up again.
Edit: Just booted up. That's a relief. Thanks.
Thare187 said:
Got it back to d/l mode. Now it's stuck at factoryfs.rfs-same as last time. I'm finished with this phone. AT&T can send me another. This is what happened to the past two phones. Stuck on a Odin restore and can't get it up again.
Click to expand...
Click to collapse
If it had happened on more than one phone, you may consider looking at odin...maybe remove and reinstall our check your drivers or computer...just double check all of little stuff that might be so obvious that they are not obvious
********
Sent from my Samsung Captivate using the XDA app
ROM: Paragon RC5 1200 mhz/100hz kernel
so if your potentially bricking the phones, what do you tell AT&T that happened? and do they not ever check or whats the deal?
As far as I know at the wareenty centers they check for physical and water if they do attempt to boot as long as nothing looks custom they wont bother with checking the recovery or key combos samsung takes care of the rest they just want functional hardware..oh dont mention anything about modding. If anything syncing crashed is the best explaination. Tested.
Sent from my replaced cappy XD
Just dont become a familair face or it might get flaged on your account. Study up before doing somthing new. Just crashed my test cappy writing this had to stop and reflash heh live and learn.
A tech here on the forums said they can tell if it has been modified in just "3 clicks".
Sent from my SAMSUNG-SGH-IDK?
noobfail said:
A tech here on the forums said they can tell if it has been modified in just "3 clicks".
Sent from my SAMSUNG-SGH-IDK?
Click to expand...
Click to collapse
Lol....uh huh....i also have a direct line to the white house
********
Sent from my Samsung Captivate using the XDA app
ROM: Paragon RC5 1200 mhz/100hz kernel
Omg really?!
Sent from my SAMSUNG-SGH-IDK?
Just messin' around....what kind of tech? Att, samsung or other?
********
Sent from my Samsung Captivate using the XDA app
ROM: Paragon RC5 1200 mhz/100hz kernel
He said he was a manager of an actual at&t walk in tech support store.
I rooted a phone and flashed to stock and returned it with no problems.
Sent from my SAMSUNG-SGH-IDK?
Sorry I'm late getting back. My phone is up and running again. Got in to D/L mode and flashed back to stock. Got stuck on the AT&T logo, but used Odin one more time and it booted right up. The first time I brought in the phone, the tech took it to the display for 2 minutes and called the warranty dept for me. I think that it helped that the Chiefs playoff game was on. They didn't seem to want to be bothered! The phone rep asked about water and physical damage. No questions about modding. The second time I did it at home over the phone. Again, no questions about modding. I told the rep both times that I was trying to transfer music to the phone via Kies and it crapped out on me. It always help to play dumb and act like you don't know too much.
Thare187 said:
Sorry I'm late getting back. My phone is up and running again. Got in to D/L mode and flashed back to stock. Got stuck on the AT&T logo, but used Odin one more time and it booted right up. The first time I brought in the phone, the tech took it to the display for 2 minutes and called the warranty dept for me. I think that it helped that the Chiefs playoff game was on. They didn't seem to want to be bothered! The phone rep asked about water and physical damage. No questions about modding. The second time I did it at home over the phone. Again, no questions about modding. I told the rep both times that I was trying to transfer music to the phone via Kies and it crapped out on me. It always help to play dumb and act like you don't know too much.
Click to expand...
Click to collapse
I had the same exact problem when i was just starting to mess around with roms and my biggest issue was the sequence that it took to flash properly. i kept opening odin then putting my phone in download mode and THEN plugging it into use as opposed to how it should have been which is holding vol up and vol down pressed then plugging in usb.
bugity said:
I had the same exact problem when i was just starting to mess around with roms and my biggest issue was the sequence that it took to flash properly. i kept opening odin then putting my phone in download mode and THEN plugging it into use as opposed to how it should have been which is holding vol up and vol down pressed then plugging in usb.
Click to expand...
Click to collapse
That's the weird thing. I'm somewhat new, but have been flashing my Captivate since Sept. When the original Cognition came out I was flashing daily. I think my problem was, it took longer than usual to flash to stock, I got impatient and didn't realize I could get to D/L mode by taking the battery out, holding power and inserting battery. I always used the button combo. Live and learn.
same problem
Ok i have the same problem as the original post stated, running odin and disconnected right at the beginning of the rom flash! this phone wont power up, and my jig (which i have used before) will not work! Is it done for!?
Ur last hope lays in adams Am I bricked thread, where u'll find an app that checks what state ur phone is in (linux or ubuntu needed)
nevermind, I tried harder and the jig worked, its one of the homemade jigs, where you cut up your charger, and use resistors to create the circut . . . . jankety but i got it to work thanks anyway though
Glad you got it, but I would buy a jig and keep it in a drawer. Just in case.

[Q] In a LOT of trouble!

So a few days back i flashed the serendipity VII rom on to my previouly 2.2 Cappy, and it worked like a charm... a day later i was experimenting with a few ROMS all 2.3, and they worked, and to my luck I flashed a 2.2 ROM (Cognition 4) (by mistake i might add) and there it was a complete black screen brick!
since then Iv tried various methods to bring it back to life, the 3button thing, the taking the battery out holding down the 3 buttons connecting the usb and putting the battery back in, then releasing power only... Iv tried to even get it JTAGed, which was a disaster since the JTAG guy tried and cudnt get the thing to show connectivity... ANY HELP??
I fail to accept that this is the end... Please HELPP!!!!!
just keep trying to get into dl mode by using other usb ports, a jig, holding buttons while battery removed and install battery then plug in phone, happened to me plenty of times but was persistant that it finally got into dl mode.
Try making a jig and putting phone in download mode then flash stock through odin -- do a search for jig in the captivate forums. It saved me many times. You can even make one for about $1.
If you had gingerbread then you may need to use the i9000 version of entering download mode. The key combination is different. Search around on the forum as plenty have already mentioned what it is. I just don't remember off the top of my head.
if it will not power on at all....it doesnt look good.
try holding volume down and power...see if that brings up download mode. a jig is only $8 shipped to your home and will work.
i had a similar scenario and a jig brought my cappy back to life!! ive had the same phone since september, the jig has saved me from at least 8 new phones
I have seen a black screen for download mode. The only way I knew I was in download was when I saw the yellow band appear in Odin. Open Odin, and try different button combinations that will get you into download mode until you see Odin recognize your phone.
I'm sure you've tried, but these are 2 other key combos. I've had that happen to me in the past and it can be frustrating.
1. volume up + volume down
2. volume down + power
3. volume down + home (softkey) then power (this is the one that worked for me)
4. volume down + menu (softkey) then power
Hope everything works out for you. If all else fails, I'm sure a jig will work.
I learned this in the days of old, when we were flashing the baked Froyo's. Don't know if it applies or if you've tried it already, but what used to work for me was:
Open Odin
Pull the battery out, put it back in...don't turn it on.
Hold the volume down button
Plug in the usb
At no point in the process should you ever touch the power button. For your Odin version, I'd recommend using the Stock Odin, get factory and then try flashing your custom Rom again.
(Edit: I say volume down because that's the current button to enter download mode with Gingerbread. It used to be Volume Up and Down at the same time.)
ok first this does not belong in the dev section! belongs in Q&A so thing will get closed pretty soon. also other than a correct jtag u cant recover with jig, button combo or voodoo magic. u just mixed a i9000 GB bootloader along with a captivate froyo secondary boot which the Cog4 ROM has. use search and i think you can find someone who offers a jtag service
Well, I've seen a few mention it, but I think your going to need to make or puchase a jig. Hit radioshack and get 3 100kohm resistors, about $1. The directions are all over the forums here. I'd be willing to bet that will fix you up.
Also, once in a while it may still be alive even though the screen is black. Like someone else said, go ahead and start Odin, then plug your phone into USB. See if there is any response from Odin. It's worth a shot.
Either way, it's good to have a Jig handy.
claim warranty.
Odin 1 click to stock then start from scratch!
EsotericSYN said:
Odin 1 click to stock then start from scratch!
Click to expand...
Click to collapse
you need dl mode to do that, he's not even getting power up. go to att store and say it wont turn on today gimme replacement.
How did someone with just 2 posts make a thread in here? I thought you had to have 10+ posts just to post in a thread.
just contact samsung the captivate should be in warraty untill oct2011.. i also bricked my phone while on serendipity VII see Q&A Soft brick or hard Brick.i had my phone stuck on the battery charge screen. was not able to get to download mode or recovery and my battery wouldnt charge . so i called samsung just gave them my imei number and they said it was under warranty until oct 2011. i did not tell them i bricked it while flashing roms. i just told them my phone wont charge or turn on. i sent my phone to the samsung repair center in dallas tx. my phone was fix at no charge even though i had it rooted and running a custom rom. samsung just fixed my looping battery screen and put there stock froyo erasing all my apps and data.it took about 2 weeks to get all this done. got my phone back this monday and everything is working great....
so just contact samsung and say the phone wont turn on dont say you rooted it or flashed a room. samsung wont check to see if its rooted all they care about is that you didnt drop the phone or something like that.
cremefraiche said:
ok first this does not belong in the dev section! Belongs in q&a so thing will get closed pretty soon. Also other than a correct jtag u cant recover with jig, button combo or voodoo magic. U just mixed a i9000 gb bootloader along with a captivate froyo secondary boot which the cog4 rom has. Use search and i think you can find someone who offers a jtag service
Click to expand...
Click to collapse
listen to this man
Same exact thing happened to me on my last phone. Your phone is dead, dead, dead. Hard bricked. Nothing will bring it back. Take it to an AT&T store and tell them you were upgrading to 2.2 and the screen went black and now it wont come back on.
There is no jig or JTAG that will fix it, trust me, I tried
timbrendelaz said:
Same exact thing happened to me on my last phone. Your phone is dead, dead, dead. Hard bricked. Nothing will bring it back. Take it to an AT&T store and tell them you were upgrading to 2.2 and the screen went black and now it wont come back on.
There is no jig or JTAG that will fix it, trust me, I tried
Click to expand...
Click to collapse
at&t might help, but you have to hassle alot.Just contact samsung they will help for sure.i just sent them my bricked phone and they fixed it in two weeks at no charge. samsung will do it for free, im living prof.
I dont really buy into the fact that its dead, no way... its just that the revisions on the boot.bin and sbl.bin are different... shouldn't JTAG work? and cant claim warranty cuz im not in the US!!! there must be a way people.... im faar too poor to just give up without a fight!!!

[Q] another bricked captivate

i just went thru a problem with a broken power button. long story short i claimed my warranty and got a refurb. the refurb had 2.2 on it. like a jerk i thought it would be fine to use this guide ( https://docs.google.com/document/pub?id=1ItSONRa9nzI7MKeKqwIdHCTRA3RRiOM_6LcJGnK4p6Y ) just like i did with my previous phone to get miui back on my phone. i had to downgrade to 2.1 on my old phone but for some reason i thought it would be fine to use the 'safe froyo base' with my already froyo phone...
anyways i got as far as odin saying it was setting partition and it would go any further. no option but to unplug and try again. before trying i tried to boot and take a look at kies. the phone wouldnt boot. just a black screen. so.. i went ahead and tried odin again since i could still get into download mode. it still hung at the same spot. pulled the plug again and put it into download mode and got the great idea of using 1-click to go back to 2.1 stock. then it hung after, i think the 3rd message that it spits out in the log. cant remember what it said but it was a normal msg. so i pulled the plug and tried to put it into download mode again. NO LUCK. and still doesnt boot.
SO, i have a non-booting, non-download mode, non-recovery mode, no signs of life captivate...
is it a refurbished turd or is there hope with a jig or something else?
i know, long story short
those instructions were for i9000 not captivate...
odin sometimes gets stuck on set partition and i wipes the params.lfs partition where the download mode image is stored.
ill bet you 100 bucks if you restart odin. take out your battery, put back in, hold both volume buttons and plug in usb, THE SCREEN WILL NOT come on, BUT odin WILL turn YELLOW in the first box and windows will beep that it found the device.
Odin will flash with a black screen. when the flash starts, you will see a blue bar on the black screen.
use the one click stock roms in the XDA CAPTIVATE development section.
use XDA. period.
so you're saying use the same method again? or use an odin 1-click stock. 2.1, 2.2, or does it even matter? cuz im pretty sure in my rage of panic i tried both one click and full another time and nothing happened. ive got nothing to lose by trying again tho. thanks for the reply.
edit: just tried what you said with the one click i have and no go. ran odin as administrator. dont have time til after work for the full method or a different one click. but i will definatley try.
FYI, regarding your question about a jig, I just had a similar problem (thread http://forum.xda-developers.com/showthread.php?p=19581785#post19581785 I tried every option on this board and many others to get into download mode without success. The jig worked (thankfully!). might be worth trying it before giving up. as for me, no more flashing until I get Outler's Unbrickable Mod.
befreewv said:
FYI, regarding your question about a jig, I just had a similar problem (thread http://forum.xda-developers.com/showthread.php?p=19581785#post19581785 I tried every option on this board and many others to get into download mode without success. The jig worked (thankfully!). might be worth trying it before giving up. as for me, no more flashing until I get Outler's Unbrickable Mod.
Click to expand...
Click to collapse
thanks for the reply. im gonna give it a few more tries before attempting the jig. my power has been out for the last 11 hours so i havent been able to use my pc... or anything really. lost all my food in refrigerator and freezer too .
im gonna mess with this thing a bit more to see if i can make a pearl out of swine poop.
maybe someone can answer me this:
considering what i did to get the phone into this state, if i try to exchange it and tell at&t that i just powered off and it simpy wouldnt power back on is there any way for them tell if it was because of what i did?
anyone? still searching and trying to get dl mode or at least my pc/odin to recognize the device. nothing has worked yet. im downloading sdk now to try adb. i have a feeling that if adb doesnt work then AdamOutler will be $30 richer . and i have an even bigger feeling that adb will not work.
nawlage, PM sent.
4-2ndtwin said:
nawlage, PM sent.
Click to expand...
Click to collapse
thanks, just read it. the thing is, the phone has no signs of life. pbl or sbl seems to be borked but not possitive. ive heard that what i did shouldnt brick it like it has been bricked.
just tried using adb. couldnt even get to it after downloading sdk. there was a read me where adb normally is and said it was moved in the version i have. i tried to install it and it just said nothing was done. could create the directory. i gotta go to work now so i cant try anything else til i get home.
looks like im gonna try for another warranty claim on the grounds that i was putting my saved data from my old phone onto my replacement with kies when the power went out and my phone froze. pulled battery and wouldnt turn back on. if im denied then ill prolly pay for the unbrickable mod. might get the mod even if i get the warranty refurb. seems like a good investment. ill post the results. thanks to those who gave ideas.
EDIT 11/25: i ended up telling them that it worked fine when i went to bed and woke up 4 hours later and it was off and wouldnt turn on. the rep tried all the things i already tried while i snickered to myself and he said 'yeah its dead'. i got another refurb stock uckb2.

[Q] I messed up. Can get into download mode that's all..

I hope someone can help me here, I'm posting with the belief that this may be a simple enough problem (With the hope).
I tried to install a Custom Recovery on my Galaxy S using this tutorial - wiki.cyanogenmod.org/w/Install_CM_for_galaxysmtd
I managed to get to step 6, and a blue bar appeared, but then i could not do step 7.
Now i cannot boot into recovery mode, nor will the phone boot past the Samsung Galaxy S logo.
I can still get into download mode, but Odin does not detect the phone.
. I have changed cable and tried different versions of Odin..
When i turn on the phone normally it shows the Samsung Galaxy S logo, blinks, and then reboots and does the same.
When i try to enter recovery, i get the same, unless i connect it to the PC. I then get an 8 pointed star, like the loading flash circle thing - the same as a flash video loading except it does not move.
I have also removed the battery and tried to enter recovery and download mode while inserting the battery.
I have removed the SIM and battery for a few minutes.
when i try to start Zadig, with the phone connected in Download mode, i get "Gadget Serial" as the device connected. I used to get "Samsung USB Composite Device"
I have tried many different things and read over the recommended threads on this forum. I think i need a bit more pointing in the right direction.
I really hope somebody can help me. I am very worried that i may have bricked it.
Thank you.
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
akash6969 said:
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
Click to expand...
Click to collapse
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.
Tomato_Jam said:
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.
Click to expand...
Click to collapse
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!
sorry to ask some stupid question, but can u make sure what versiom ur fone is?
is it i9000?, or i9001 or i9003? or korean anycall? as far as i know, flashing i9000 ROM to i9003 will hardbrick da device.
Sent from my GT-I9000 using xda premium
akash6969 said:
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!
Click to expand...
Click to collapse
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.
Tomato_Jam said:
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.
Click to expand...
Click to collapse
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD
You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1
Soryuu said:
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD
Click to expand...
Click to collapse
huskyT said:
You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1
Click to expand...
Click to collapse
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
 @Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).
Tomato_Jam said:
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
@Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).
Click to expand...
Click to collapse
Don't stress mate, we all have bad days, we all make mistakes
Sent from my GT-P7510 using Tapatalk HD
Well....
I would have been quicker if i had ordered a jig and done it myself.. (Worth mentioning, i had told guy in phone shop what happened, and about the required "jig")
I collected my phone from the shop today, after a week, and i was told "Your phone is f*****d". To which i replied, "what? are you sure, i mean, i have only flashed it with SGS2 firmware, i'm under the impression it is very hard to break/brick, if i have a jig."
He told me, "Nope, it's beyond repair, it won't work. If you want, i can use the screen and other parts, i'll buy it off you for €40"
No thanks.
So now i am on the lookout for a premade jig. Does anybody know where i can buy one?
I meant to last week, but things happened, and without a phone i was running around a bit...
I'm going to check ebay, but if somebody could recommend somebody reliable, i'd prefer that. Thanks.
I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....
rodman01 said:
I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....
Click to expand...
Click to collapse
Thanks.
I bought a jig, and it arrived today. Have phone in charger.
Do i just plug the jig in?
Or do i also do the three button press?
The screen is completely black, and nothing appears on it.
only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:
rodman01 said:
only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:
Click to expand...
Click to collapse
Thanks, going to leave it charging for a little longer, and try it.
If it doesn't work, would a motherboard for the Samsung Galaxy S be easy to replace? I have found one unlocked for €25.
EDIT
Found a tear down video here - http://www.youtube.com/watch?v=vxPWsLd05F4
yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.
rodman01 said:
yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.
Click to expand...
Click to collapse
Thanks again.
I am after removing it from the charger, and inserted the jig. It's in about 30 seconds now, and nothing is happening..
that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....
rodman01 said:
that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....
Click to expand...
Click to collapse
What seems to have happened, is i tried to flash it with SGS2 rom. So is it unbrickable?
I am not sure but I think that minimum the bootloader is damaged...there is one more possibility: to repair it via jtag...but for this you have to find someone, who ones one and can repair it....some of the guys don't take much money for such a repair, but with transport costs ets...perhaps it would be cheaper and faster if you take the new mainboard you mentioned.

Categories

Resources