Stuck in loop! - Galaxy S I9000 Q&A, Help & Troubleshooting

I have a galaxy S
When i get to the homescreen, 10 seconds later it loops back to the intro animation (Animated S)
This does not happen if i immediatly go into airplane mode
i have found that wifi is what is causing the issue here
SO, Assuming i can only using my device an airplane mode
how can i flash a new rom?
i am rooted
clockwork is not installed.
when i get into recovery its just the stock recovery window, if i try to apply an update.zip i just get... verification failed
i have tried wiping.

antipesto93 said:
I have a galaxy S
When i get to the homescreen, 10 seconds later it loops back to the intro animation (Animated S)
This does not happen if i immediatly go into airplane mode
i have found that wifi is what is causing the issue here
SO, Assuming i can only using my device an airplane mode
how can i flash a new rom?
clockwork is not installed.
when i get into recovery its just the stock recovery window, if i try to apply an update.zip i just get... verification failed
i have tried wiping.
Click to expand...
Click to collapse
So you are on complete stock? No root?
If so I would suggest pulling the battery, waiting a few minutes, replacing it and trying to boot up again. If it still loops, take it to your carrier for repair.
Sent from my GT-I9000 using XDA Premium App

edit: yeah i am rooted
the recovery is defiantly stock
it was purchased second hand

Dont go to vendor!!! yet
antipesto93 said:
Yeah complete stock, it was rooted but i wiped/restored so i assume its at stock now
the recovery is defiantly stock
it was purchased second hand
Click to expand...
Click to collapse
No dont turn it in to repair yet first try downloading odin and do as follows (very easy way to fix it)
http://www.theandroidsoul.com/fuguroot-galaxy-s-how-to If u r rooted then skip this link!!!
thne go and do
http://forum.xda-developers.com/showthread.php?t=1025348
Edit : If u r rooted then ur vendor might not help u as rooting breaks the warrenty.

Zionator said:
No dont turn it in to repair yet first try downloading odin and do as follows (very easy way to fix it)
http://www.theandroidsoul.com/fuguroot-galaxy-s-how-to If u r rooted then skip this link!!!
thne go and do
http://forum.xda-developers.com/showthread.php?t=1025348
Edit : If u r rooted then ur vendor might not help u as rooting breaks the warrenty.
Click to expand...
Click to collapse
OH
MY
GOD
THANK YOU SO MUCH
Did the ODA kernal thing and its working FINE now
If i could i would hug you

antipesto93 said:
OH
MY
GOD
THANK YOU SO MUCH
Did the ODA kernal thing and its working FINE now
If i could i would hug you
Click to expand...
Click to collapse
lol no worrys xda is here for all to help one and other
I know how it is to be stuck with something annoyin.
Ps. u could give me a thanks button press tho hehe so my zero becomes a one

Zionator said:
lol no worrys xda is here for all to help one and other
I know how it is to be stuck with something annoyin.
Ps. u could give me a thanks button press tho hehe so my zero becomes a one
Click to expand...
Click to collapse
edit: done

Related

Continuum v5.1, v5.2 got big trouble

Hi Experts,
I have a Cappy and i love Continuum 5 ROM. I never miss any versions from beta2 to RC 3, everything is ok, but now when contimuum v5.1 was released. I tried to flash it but i got a big problem in that version. The first, i encountered Boot Loop issue while booting, but it's not the biggest problem, my cappy is still boot up to the home screen, and here everything was became very bad. My Cappy got lag and cant interact with return and it reboot automatic after that.
Now, when v5.1 was released, i believed it'll be fixed, but it's still exists. .
my cappy cant boot up to home screen. it repeats booting to continuum animation and restart forever.
can anybody give me a suggestion for turning my cappy back !!!!!!!! Please help
Did you have full battery? I made this mistake too... Be sure that you did everything correctly..
Sent from my captivate using XDA App
I would suspect you could simply use the 1-CLICK ODIN program to restore the phone then follow the steps carefully for 5.1 (which is a pretty awesome ROM btw)
I'm sure i charged full battery before flashing.
ProBoner said:
I would suspect you could simply use the 1-CLICK ODIN program to restore the phone then follow the steps carefully for 5.1 (which is a pretty awesome ROM btw)
Click to expand...
Click to collapse
i flashed to stock room with odin3 1.7 (using PDA + PIT files. i did that successful many times with 2.2 ). but now, with 2.3.3 i got brick( maybe lost boot), although flashed by odin without any errors ( 1 succeed/ failed 0) .
now i cant make the cappy go to download mode. please helppppp.
3 buttons with no interaction !!
sounds like u flashed a stock rom that didnt have old bootloader, safe way to have done it is with non 3 button fix odinoneclick flash to stock. dunno if a JIG will help u get back into download mode
CremeFraiche said:
sounds like u flashed a stock rom that didnt have old bootloader, safe way to have done it is with non 3 button fix odinoneclick flash to stock. dunno if a JIG will help u get back into download mode
Click to expand...
Click to collapse
Really, can i get back by using JIG ? My cappy cant boot up anymore. still pess power button but nothing was display.
longdct said:
Really, can i get back by using JIG ? My cappy cant boot up anymore. still pess power button but nothing was display.
Click to expand...
Click to collapse
You do know that download mode volume down and power, or volume down and usb connection? Figure might as well say cause I had what looked to be black screen before, but went in download mode. And can you not odin one click?
Ps. I have had stay black till reboot but if it give com port even with black screen it is in download mode
Sent from my GT-I9000 using XDA Premium App
leezrd said:
You do know that download mode volume down and power, or volume down and usb connection? Figure might as well say cause I had what looked to be black screen before, but went in download mode. And can you not odin one click?
Ps. I have had stay black till reboot but if it give com port even with black screen it is in download mode
Sent from my GT-I9000 using XDA Premium App
Click to expand...
Click to collapse
Thanks Leezrd, i tried these methods but nothing was happened. the Odin3 cant recognize any com port
longdct said:
Thanks Leezrd, i tried these methods but nothing was happened. the Odin3 cant recognize any com port
Click to expand...
Click to collapse
Have you tried odin one click I heard that if odin 3 doesn't work odin one click will
Sent from my GT-I9000 using XDA Premium App
leezrd said:
Have you tried odin one click I heard that if odin 3 doesn't work odin one click will
Sent from my GT-I9000 using XDA Premium App
Click to expand...
Click to collapse
I wish i have a chance to do this. but now i cant go to download mode. it makes me so sad.
longdct said:
I wish i have a chance to do this. but now i cant go to download mode. it makes me so sad.
Click to expand...
Click to collapse
Get a jig and use it to get into DL mode. Please make 100% sure you know what you are doing before you flash.
longdct said:
I wish i have a chance to do this. but now i cant go to download mode. it makes me so sad.
Click to expand...
Click to collapse
Use command command prompt. "/android" Then "adb shell" then "su" then "roboot download" might not work with adb but could give it a try
Sent from my GT-I9000 using XDA Premium App
zelendel said:
Get a jig and use it to get into DL mode. Please make 100% sure you know what you are doing before you flash.
Click to expand...
Click to collapse
thanks for your help. if it really lost bootloader, JIG has any effect? if terrible thing is true. can u tell me how i can do to relive my phone ?
longdct said:
thanks for your help. if it really lost bootloader, JIG has any effect? if terrible thing is true. can u tell me how i can do to relive my phone ?
Click to expand...
Click to collapse
Your best bet is the jig. If that doesnt work then I would try and get a warrenty replacment. I went over the thread and it stated that if you get a bootloop you should boot into recovery and reflash the rom, did you do that?
longdct said:
thanks for your help. if it really lost bootloader, JIG has any effect? if terrible thing is true. can u tell me how i can do to relive my phone ?
Click to expand...
Click to collapse
If you lost bootloader then you will have to JTAG, if your under warranty you can say you were updating to froyo and it turned off and never turned back on
Sent from my GT-I9000 using XDA Premium App
zelendel said:
Your best bet is the jig. If that doesnt work then I would try and get a warrenty replacment. I went over the thread and it stated that if you get a bootloop you should boot into recovery and reflash the rom, did you do that?
Click to expand...
Click to collapse
he can't get a turn on so probably not able to get in recovery but to OP with gb recovery is volume up and power
Sent from my GT-I9000 using XDA Premium App
i was having some issues gettin my captivate into download mode using odin to go back to stock also. what worked for me however was to have usb plugged into comp and phone and THEN hold volume up and down. port was then recognized and i went to download. badda bing badda boom.
zelendel said:
Your best bet is the jig. If that doesnt work then I would try and get a warrenty replacment. I went over the thread and it stated that if you get a bootloop you should boot into recovery and reflash the rom, did you do that?
Click to expand...
Click to collapse
right. i got a bootloop when flash to v5.2. i tried to flash the rom in recovery mode many times, but it's still exists. even i flash back to RC3. i got only the android text animation on the screen.
thus i have to flash to the stock by that way. and now i got a brick
I've had problems in the past with getting to download mode on the cappy. I did some googling trying to find a way, ended up finding a very good page on it:
http://samsungcaptivate.wikia.com/wiki/Putting_the_Phone_into_Download_Mode
I hope that helps.
Had the same problem with my cappy. The problem is that after all you did, you have one bootloader from i9000 and another from i897. The jig won`t help. I`ve found the people that recovered the phone with JTAG.

[Q] Help? boot loop at samsung logo!!

Help i was playing fruit ninja on my ace with cm 7.2 by vo-1..... after some time my phone became very hot so i turned if off for a while then switched it back on then this what happens it loops on samsung logo ...i cant boot into CWM recovery but luckily i could go into download mode and i tried to flash stock rom through odin but unfortunately after completion when it tries to boot it loops continuosly on samsung logo;-(
ANY HELP?..
Try to flash a mulit-package rom like 2.3.3 KP0.
Farooq95 said:
Help i was playing fruit ninja on my ace with cm 7.2 by vo-1..... after some time my phone became very hot so i turned if off for a while then switched it back on then this what happens it loops on samsung logo ...i cant boot into CWM recovery but luckily i could go into download mode and i tried to flash stock rom through odin but unfortunately after completion when it tries to boot it loops continuosly on samsung logo;-(
ANY HELP?..
Click to expand...
Click to collapse
no need! just do a factory wipe! thats it!
Sent from my GT-S5830 using xda premium
jinavs did you read this:
i cant boot into CWM recovery
Click to expand...
Click to collapse
But Farooq95 have you try to go to the stock recovery after flashing the stock rom?
dragonnn said:
Try to flash a mulit-package rom like 2.3.3 KP0.
Click to expand...
Click to collapse
yes i even tried to go into stock recovery but same thing happens
When you flash the mulit-package and you can't go into recovery then I think you phone is damaged. Only what can you try more is using adb to get into recovery:
Code:
adb reboot recovery
At boot loop you mean the Samsung boot animation - or the logo that displays immediately when you try turn on you phone?
dragonnn said:
Try to flash a mulit-package rom like 2.3.3 KP0.
Click to expand...
Click to collapse
i have flashed stock S5830JPKKP9 wich is my baseband But can u provide me link for 2.3.3 kpo
Is S5830JPKKP9 a mulit-package? When yes than it isn't necessary to flash 2.3.3 KP0, doesn't make any difference. You can found 2.3.3 KP0 here https://hotfile.com/dl/127701476/7d30a8b/S5830XWKPO.rar.html but this is an European rom.
The logo when i immediately turn on da phone
I have bad news to you - I think you phone is damaged. Only what you can do is flash a mulit-package. When this doesn't help you must go to the service center. But try before turn on you phone put out the battery for a few minutes.
EDIT
Have posted wrong link, post edited - now it's ok.
Thanks for your effort ill try that... but wat is multipackage? Can i use adb to get into recovery as u said before?
multipackage is an firmware that is split in more files - flashing it make a eraser of all internal memory (have update my previous post whit correct link). You can try adb, but I think you will get "error - no device" because adb works on when the kernel boots - that means it will help when you have a classic boot loop on the boot animation - not on the SAMSUNG logo.
Are u sure that there is no other way to fix this?
Definitely yes.
Pls say cause im taking this to service centre 2morrow
I think the problem is you have overheat you phone - did you play on it when charging the battery? And second I think it isn't good to turn of you phone when he gets hoot - better to let it on and cools slow down.
I found out what really caused this problem so the day before i installed this app called "mobile odin" it asked me root permissons so i allowed it..then it said that the app is not compable with my device and then it asked me to allow it to create a dump file and it said that it could take almost 30 mins to complete and make that app compatible with my device...so i allowed it after 30min it said finished dumping after that i didnt switch off or reboot the phone that day...but i rebooted the phone the other day when it became hot while playing which caused this problem...i am saying this because some other user bricked his/her phone the same way!
I think I lost my phone now the same why -.- damit
Farooq95 said:
I found out what really caused this problem so the day before i installed this app called "mobile odin" it asked me root permissons so i allowed it..then it said that the app is not compable with my device and then it asked me to allow it to create a dump file and it said that it could take almost 30 mins to complete and make that app compatible with my device...so i allowed it after 30min it said finished dumping after that i didnt switch off or reboot the phone that day...but i rebooted the phone the other day when it became hot while playing which caused this problem...i am saying this because some other user bricked his/her phone the same way!
Click to expand...
Click to collapse
While MobileOdin is not compatible with a Galaxy Ace http://forum.xda-developers.com/showthread.php?t=1347899 I'm not sure how it would have bricked your phone when you didn't actually ask it to do anything.
As others have said, considering the inability to enter recovery after flashing a new bootlader & rom etc, a hardware error appears more likely perhaps as a result of overheating.
Too late it had to replace motherboard....
Sent from my GT-I9100 using xda app-developers app

[Q] Superbrick, Softbrick, Pixel Salad ?huh?

Seriously can someone please explain to me what the heck the above mean? I get the notion of a brick but what the heck is the difference between Super brick? Hard / Soft Brick? Finally, not really brick but what's Pixel Salad!?
Thanks!
altrstar said:
Seriously can someone please explain to me what the heck the above mean? I get the notion of a brick but what the heck is the difference between Super brick? Hard / Soft Brick? Finally, not really brick but what's Pixel Salad!?
Thanks!
Click to expand...
Click to collapse
Soft brick= a FAILURE of the device that can be reverted by the user
Hard brick= a FAILURE of the device that has to be reverted via external devices see jtag
Superbrick= a FAILURE of the device where the only solution the service center and a replacement of the component that malfunctions.
Pixel salad = a problem of the graphics unit or the screen to display correctly the image and put instead random colored pixels on some areas of the screen or the whole screen.
This is my interpretation of those issues everyone can correct it if he thinks that those expansions are incorrect.
Hope it helped you understanding few of those issues.
GL& HF
Sent from my GT-N7000 using Tapatalk 2
Braxos said:
Soft brick= a FAILURE of the device that can be reverted by the user
Hard brick= a FAILURE of the device that has to be reverted via external devices see jtag
Superbrick= a FAILURE of the device where the only solution the service center and a replacement of the component that malfunctions.
Pixel salad = a problem of the graphics unit or the screen to display correctly the image and put instead random colored pixels on some areas of the screen or the whole screen.
This is my interpretation of those issues everyone can correct it if he thinks that those expansions are incorrect.
Hope it helped you understanding few of those issues.
GL& HF
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
You are spot on!!
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me ?
Is there any possibilities to get the phone fixed?
Thank you all for your answers allready
Wish u all a nice day
Nefret90 said:
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me
Click to expand...
Click to collapse
I'm not 100% sure, but performing a flash under lpf isn't recommended. How did you root lpf after flashing? And when you say "did a direct reboot" what do you mean? Also when you say doesn't turn on at all, do you mean no display whatsoever or enters Samsung boot loop? Are you able to enter recovery or download mode?
Sent from my GT-N7000 using xda premium
Nefret90 said:
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me ?
Is there any possibilities to get the phone fixed?
Thank you all for your answers allready
Wish u all a nice day
Click to expand...
Click to collapse
You should have read the warning about LPx kernels (LP1, LP5, LP6, LPY, LPF)
Wiping or flashing in recovery will probably cause superbrick.
Sent from my GT-N7000 using XDA
Nefret90 said:
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me ?
Is there any possibilities to get the phone fixed?
Thank you all for your answers allready
Wish u all a nice day
Click to expand...
Click to collapse
The way to go from ANY non-CM9-based ICS Rom to a CM9-based Rom is via Gingerbread.
You should've first used PC Odin to go back to GB, root your Rom, then flash CM9.
You have most probably superbricked your phone.
SpyderTracks said:
I'm not 100% sure, but performing a flash under lpf isn't recommended. How did you root lpf after flashing? And when you say "did a direct reboot" what do you mean? Also when you say doesn't turn on at all, do you mean no display whatsoever or enters Samsung boot loop? Are you able to enter recovery or download mode?
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
Did root using cfs root trough Odin Pc. With a direct boot i mean that i just rebooted without doing the partiton thing just flashed the image and rebooted.
And when i say doesnt turn on at all i mean that absolutely nothing happens, no power at the screen no detection trough usb on pc no download mode or anything.
tryied to flash before and did just reboot, back then did just got the boot looop probem and did a recovery to ics. this last time i tried again to show a friend in a hurry and failed epicly
Nefret90 said:
Did root using cfs root trough Odin Pc. With a direct boot i mean that i just rebooted without doing the partiton thing just flashed the image and rebooted.
And when i say doesnt turn on at all i mean that absolutely nothing happens, no power at the screen no detection trough usb on pc no download mode or anything.
tryied to flash before and did just reboot, back then did just got the boot looop probem and did a recovery to ics. this last time i tried again to show a friend in a hurry and failed epicly
Click to expand...
Click to collapse
You are definitely bricked, I fear. Head to the nearest service centre.
I am from Kuwait ..
I purchased Samsung galaxy Note N7000 15 Days before
I have Installed King Droid ICS mania 2.1 later yesterday i updated to King droid ICS mania 3.0 and Samsung galaxy s3 Mod updated .. after that i restarted my NOTE but its not booting
i can go to Download mode and Recovery mode ..
even i can see the Install ZIP from SD card and all in CW ..when i Update it says
Can't Mount EMMC
I tried to Mount also But failure ..
I tried Stock rom of ICS official to Update Using ODIN 1.85 .. it stops at
<ID:0/008> factoryfs.img ..
I am worried I cant go for warranty Bcoz at Boot It says Binary count (5)
Please Help me Out

Galaxy Note stuck at Samsung logo after automatic update..PLEASE HELP..!!

Hi guys,
First of all m a noob here and got here after doing alot opf research on google but have not find any solution yet. I have got a major issue with Galaxy note, never been rooted.
So I have been using ICS on my Galaxy Note for almost a month now, and a week ago, I saw a message telling me that an update had been downloaded and the phone would be rebooted to install the update.
I clicked the OK button in the dialog box, and my phone did reboot but is now stuck at the flashing Samsung logo (after the initial musical animation, which incidentally was terminated midway).The phone got quite hot after about 20 minutes, so I switched it off by pressing the power button. Then I switched it back on after a while, and it was stuck at the flashing Samsung logo. N now its stuck there..
Restart does not work...
Recharging does not work...
Battery swap does not work..
I contacted the service center, they say they will flash the firmware but all the data will be lost and also they are not taking this in WARRNTY.
Can anyone help me with this please.. its been dead for a week now.
sorry for bad english
re:
Also tried POWER OFF+VOL UP+HOME .. a android green logo comes up. but again phones goes to samsung logo and stucks...
however,POWER OFF+VOL DOWN+HOME button gets me to a yello triangle logo and asks if you want to install custom rom...
Please help me guys...!!
^^
where you using the stock kernel itself on ICS?
do the latter..
boot to download mode, then try to flash your phone back to GB using PC ODIN. Once it's in stock GB, work your way up again to ICS. And oh by the way.. sorry to tell you this, but I don't think you can recover back your data after since this process will erase everything on your phone.
letters_to_cleo said:
^^
where you using the stock kernel itself on ICS?
do the latter..
boot to download mode, then try to flash your phone back to GB using PC ODIN. Once it's in stock GB, work your way up again to ICS. And oh by the way.. sorry to tell you this, but I don't think you can recover back your data after since this process will erase everything on your phone.
Click to expand...
Click to collapse
Thank you for the quick rply Sir,
actually i have no idea about stock kernel, as i said my phone was unrooted ,and only thing i did was using just small cracked apps sometimes.
So which stock GB should i download, there are so many here and m confused which one will work for me.
Thanks in advance Sir.
ankyyy said:
Thank you for the quick rply Sir,
actually i have no idea about stock kernel, as i said my phone was unrooted ,and only thing i did was using just small cracked apps sometimes.
So which stock GB should i download, there are so many here and m confused which one will work for me.
Thanks in advance Sir.
Click to expand...
Click to collapse
hey.. dont' sir me.. we're not in the Army or in the military here okay Just call me John.. that's my name...
Here - >http://forum.xda-developers.com/showthread.php?t=1424997 (courtesy of our good 'ol doc Ketan), Look for the stock GB of your region ( Page #2) and download it on your PC. Use PC Odin to flash it to your phone (in download mode)
letters_to_cleo said:
hey.. dont' sir me.. we're not in the Army or in the military here okay Just call me John.. that's my name...
Here - >http://forum.xda-developers.com/showthread.php?t=1424997 (courtesy of our good 'ol doc Ketan), Look for the stock GB of your region ( Page #2) and download it on your PC. Use PC Odin to flash it to your phone (in download mode)
Click to expand...
Click to collapse
Ok, Thanks again John.
i have i more doubt. The stock rom thread says "Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly". i have installed kies but when i connect my phone to it, it gives me Mtb driver bot installed properly error.. would it create a problem?
Yes it would.. try to completely uninstall and reinstall Kies and try later on, to plug your phone again.
letters_to_cleo said:
Yes it would.. try to completely uninstall and reinstall Kies and try later on, to plug your phone again.
Click to expand...
Click to collapse
Ok John,
M following your steps now,reinstalling kies and then flashing with gb rom. Hope it would work well. Will update you whatever happens.
Thanks again Bro,,!!
Sure! no fret! you can do it.. have confidence in yourself bud.
By the way.. don't forget my sig below?

[Q] Boot loop, not sure what i did or how to fix

Hey,
Tried to root my galaxy s using this guide:
theandroidsoul .com/how-to-root-xwjw1-firmware-for-galaxy-s-i9000/
First attempt I somehow soft bricked it, did it again and it said sucess but now it's stuck in boot loop.
Complete noob and not really sure what went wrong or where to go from here, any help would be great.
what rom do you use?
自由自我 said:
what rom do you use?
Click to expand...
Click to collapse
I'm not really sure.. I've never messed with my phone much. stock?
Anyone?
Can you go to download mode?
Sent from my GT-I9000 using xda app-developers app
wget21 said:
Can you go to download mode?
Sent from my GT-I9000 using xda app-developers app
Click to expand...
Click to collapse
yeah i can.
loopn said:
Anyone?
Click to expand...
Click to collapse
Nothing to worry..
Access download mode and flash a stock Rom via Odin.
here instruction, but make sure its i9000 first n read carefully
http://forum.xda-developers.com/showthread.php?t=2149455
Sent from my GT-I9000 using xda premium
compacity said:
here instruction, but make sure its i9000 first n read carefully
http://forum.xda-developers.com/showthread.php?t=2149455
Sent from my GT-I9000 using xda premium
Click to expand...
Click to collapse
Is there anyway without losing my app data and such? The whole reason I wanted root was to backup my phone.
loopn said:
Is there anyway without losing my app data and such? The whole reason I wanted root was to backup my phone.
Click to expand...
Click to collapse
find cf root, or use semaphore kernel
bootloop becoz wrong kernel flashed, knowing ur build number is important to determine which cf root u needed
if u find da suitable kernel, bootloop will fix by flashing thru odin, but ur sayin u dont even know da version here, so it become more difficult.
here list of cf root
http://forum.xda-developers.com/showthread.php?t=788108
but as i said before da difficulty now is u dont even know ur build number n version but ur sayin u wanna backup ur app data but ur fone bootloop now.
Sent from my GT-I9000 using xda premium
same problem but a bit different
Hello people,
Uhm i am completely new to the forum but i got the same problem.
I somehow got stuck in a boot loop with my sgs gt-i9000.
It gets to the giant S logo and stays there then it starts buzzing now and then.
and i cant get into download mode or recovery mode.
i have been trying everything for almost half a year now and i still cant get in.
maybe you can help?
thanks in advance.
3 button combo? jig?
its juz bootloop, try jig if 3 button combo not working
u sure its i9000? not diff version of i9000?
Sent from my GT-I9000 using xda premium
im sure
The 3 button combo is not working, we tried a jig 2 and i tried multiple 3-BC repairs using Odin, Heimdall and KIES.
and yes i am sure it is a Samsung galaxy S GT-I9000.
scytch said:
The 3 button combo is not working, we tried a jig 2 and i tried multiple 3-BC repairs using Odin, Heimdall and KIES.
and yes i am sure it is a Samsung galaxy S GT-I9000.
Click to expand...
Click to collapse
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps!
Nope not one button combo works i tried it all.
scytch said:
Nope not one button combo works i tried it all.
Click to expand...
Click to collapse
Have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
You must read this ... Seriously everyone.
akash6969 said:
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps!
Click to expand...
Click to collapse
DUDE!!!! I have the samsung galaxy s4 att sgh-i337. I recently just tried flashing uxylon from the goo manager . I did standard procedure of factory reset twice, then cache and dalvik cache wipe two times. Just so happens as Im waiting for uXylon or whatever its spelled to flash , my phone decides to stay at the boot screen.... At this point im sweating. After a few minutes i take the battery out and restart regularly . I restart and wait 10 minutes thinking it still may flash uxylon. NOPE. :,( Now im getting really scared. I try to the custom recovery mode.... no twrp OR SYSTEM RECOVERY .... Now Im Falling over scared. I take out battery try again. power , home , volume up , repeatedly . It wont even say booting recovery it only says recovery options then black screen untill I release the buttons. . Then bootloop to logo no recovery. Now Im frantic. I look up adam outler's page on ODIN recovery with stock firmware and ddownload ucuadml and ucuamdb not knwoing which , if either of them , would flash through ODIN. So im frantically flying through the web for 3 hours searching some magic button combo or something that may help me just reach my recoveries in twrp (since the computer would not recognize even in download mode) . I look everywhere. EVERYWHERE. This point i figure i can try odin and its my last chance. Im waiting on the firware to download right now to this second as I type . Somehow God magically guided me to this page though ... because I did about 300 google searches looking for a way to get my twrp back and use my nandroids. NOTHING until now..... I run across this post and move down and come across your post. "have you tried this button combo ? " I read the next comment . "NO no combos worked." Clciked forward a few pages and found nothing. Im giving up ... its over... Either ODIN will work and flash my stock firmware or I will have no way to turn my paper weight back into a cell phone. As Im click the back button i come across THIS post YOUR actual comment. I read it and think ... I didnt try that. I tried it the way you posted. Home + volume up ... nothing happens .... I add the power button and it boots same way as before booloop. Im infuriated..... I press it again the way you posted and suddenly ..... TWRP's beautiful blue screen pops up !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! I rostroe my cleanROM 1.0 nand and Im back up . I seriously just want to thank you for posting this little comment that you probably thought would never really help anyone at all. This truly TRULY just saved my phone . I mean you just saved my day , brother. Seriously thank you . Im so happy right now it's like I bought a brand new s4 lol. Thank you so much buddy. Real talk. :highfive:
sky_fox said:
DUDE!!!! I have the samsung galaxy s4 att sgh-i337. I recently just tried flashing uxylon from the goo manager . I did standard procedure of factory reset twice, then cache and dalvik cache wipe two times. Just so happens as Im waiting for uXylon or whatever its spelled to flash , my phone decides to stay at the boot screen.... At this point im sweating. After a few minutes i take the battery out and restart regularly . I restart and wait 10 minutes thinking it still may flash uxylon. NOPE. :,( Now im getting really scared. I try to the custom recovery mode.... no twrp OR SYSTEM RECOVERY .... Now Im Falling over scared. I take out battery try again. power , home , volume up , repeatedly . It wont even say booting recovery it only says recovery options then black screen untill I release the buttons. . Then bootloop to logo no recovery. Now Im frantic. I look up adam outler's page on ODIN recovery with stock firmware and ddownload ucuadml and ucuamdb not knwoing which , if either of them , would flash through ODIN. So im frantically flying through the web for 3 hours searching some magic button combo or something that may help me just reach my recoveries in twrp (since the computer would not recognize even in download mode) . I look everywhere. EVERYWHERE. This point i figure i can try odin and its my last chance. Im waiting on the firware to download right now to this second as I type . Somehow God magically guided me to this page though ... because I did about 300 google searches looking for a way to get my twrp back and use my nandroids. NOTHING until now..... I run across this post and move down and come across your post. "have you tried this button combo ? " I read the next comment . "NO no combos worked." Clciked forward a few pages and found nothing. Im giving up ... its over... Either ODIN will work and flash my stock firmware or I will have no way to turn my paper weight back into a cell phone. As Im click the back button i come across THIS post YOUR actual comment. I read it and think ... I didnt try that. I tried it the way you posted. Home + volume up ... nothing happens .... I add the power button and it boots same way as before booloop. Im infuriated..... I press it again the way you posted and suddenly ..... TWRP's beautiful blue screen pops up !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! I rostroe my cleanROM 1.0 nand and Im back up . I seriously just want to thank you for posting this little comment that you probably thought would never really help anyone at all. This truly TRULY just saved my phone . I mean you just saved my day , brother. Seriously thank you . Im so happy right now it's like I bought a brand new s4 lol. Thank you so much buddy. Real talk. :highfive:
Click to expand...
Click to collapse
Glad it worked for you!! Lots of people on this Forum have helped me out when I was in a similar situation, I'm really happy that it helped you..
Enjoy your phone!:good:
akash6969 said:
Glad it worked for you!! Lots of people on this Forum have helped me out when I was in a similar situation, I'm really happy that it helped you..
Enjoy your phone!:good:
Click to expand...
Click to collapse
Thats what its all about bro. Advancing that community . More commmunity helped out the more testing of these great works of the awesome developers. I know some on the forums would say thats wrong but you showed me what it all about. Good luck , man. Thanks for the help.
compacity said:
find cf root, or use semaphore kernel
bootloop becoz wrong kernel flashed, knowing ur build number is important to determine which cf root u needed
if u find da suitable kernel, bootloop will fix by flashing thru odin, but ur sayin u dont even know da version here, so it become more difficult.
here list of cf root
http://forum.xda-developers.com/showthread.php?t=788108
but as i said before da difficulty now is u dont even know ur build number n version but ur sayin u wanna backup ur app data but ur fone bootloop now.
Sent from my GT-I9000 using xda premium
Click to expand...
Click to collapse
Got it going again, now the storage doesnt seem to be working, won't scan on startup.

Categories

Resources