[Q] Help me pls.. I think I've really bricked my P990 - LG Optimus 2x

Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...

humblepie88 said:
Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...
Click to expand...
Click to collapse
Try using SmartFlashTool, download the LG stock ROM (can be found here in XDA forum, i'll help you find the link), flash the .bin and .fls files.

humblepie88 said:
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
...
"Hold the vol+ button and power key before plugging in but the smarttool did not find the com port..."
Click to expand...
Click to collapse
Turn off the phone. Hold Vol-DOWN while plugging it in. Start Smartflash and see the com-ports magically appear.

Follow trymhansen's instructions. He helped me before with my softbricked phone.

I hope you get your O2X back to life! Keep us posted
Best of luck to you!
PS. I also believe you should pull out the battery after turning off the phone in Trym's instructions. Trym correct me if I'm wrong please.

Hi All,
Thanks for your kind replies. I did follow your instruction. Take out the battery (I removed the ext SDcard as well), press and hold -vol and plug in the phone via USB. Afterwhich start up smartflash tool.. still nothing happens and no com ports are found.. The version of smartflashtool that I used is Dec 2010. Do I need to get the latest one and also the LG united drivers installed?
I also tried starting smartflash tool before the sequence.. still the same. BTW.. my OS is Win 7. Is it supported?
Really at my end's wit. Hope I can bring my phone back to life soon and I'm not really bricking it. I heard Samsung phones are not that easy to brick and can get to the recovery mode pretty easily. is it true?
Please help me.. thanks

Hi bros,
Attached are my screenshots from the device manager and smartflash tool... both seems not able to find the phone and allocate a com port. I've tried installing the latest LG mobile driver 3.6 but no help as well

Have you followed instructions as described here http://forum.xda-developers.com/showthread.php?t=1008070 ?
Also, try to attach your phone directly to computer, using usb ports from computer mainboard. I have experienced problems when attaching it via extension usb cord or attaching it to computer case ports. (I hope that you can understand what I have mean to say with usb )

Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...

humblepie88 said:
Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...
Click to expand...
Click to collapse
launch smartflashtool first, extract the .fls and .bin files, hold down volume at the same time plug in the usb port to your comp. you must see a s/w updating logo in your phone's screen and smartflash should detect your phone. then click start!
Sent using a phone.

Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..

humblepie88 said:
Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..
Click to expand...
Click to collapse
does the laptop have lg drivers installed?
Sent using a phone.

inflance hotota
mrgian said:
does the laptop have lg drivers installed?
Sent using a phone.
Click to expand...
Click to collapse
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable

humblepie88 said:
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable
Click to expand...
Click to collapse
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.

try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help

chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
you got a point there.
Sent using a phone.

humblepie88 said:
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
Click to expand...
Click to collapse
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.

LarsPT said:
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.
Click to expand...
Click to collapse
I've tried the recovery via 2 diff laptops and plugging in directly to one of the side USB ports but to no avail as well.. I think I've plugged in the phone correctly but there's no reaction at all/

mrgian said:
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.
Click to expand...
Click to collapse
How to enter CWM? I can't even power up the phone and no reaction at all when plugged into USB via smartflash.. the screen remains black. It's liked the whole phone is burned or something... but strange thing is that it can detect APX and asked to install drivers... but after successfully installing the Nvidia boot recovery driver.. the com ports does not get discovered.. What is wrong?

chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
I plugged in the phone with battery but there was no charge logo or whatever.. the screen remains blank.. I'll try to leave it charging and see what happens. But I've remembered there was still about 80% power when this disaster happened and I've taken out the battery since.. so the charge should have remain? Btw.. where can I get this ext3 back.zip and how to use it? thanks

Related

Captivate dead? Boot to blank black screen

Need some help trying to figure out how to make my Captivate turn on...I press power and get the AT&T slash screen and then the galaxy s logo loads for about 3 minutes and goes to blank dark screen with the capacitive buttons lit. this is not good because my **** won't boot into recovery either
You should flash to stock then...pull battery, hold volume buttons and plug in usb with odin loaded and ready on the computer. There's plenty of threads to help you out
Sent from my phone so excuse the spelling errors
Funnily enough... My phone just did that too. I was installing Mort Widget and it just totally bricked...
I'm rather p!ssed at this...
Course this was after it deleted all my email accounts and SMS.
What you'll need.
Odin (search or look in any of the ROM/Firmware threads, for example the i9000 ROM or unofficial JH2 or JH3 ROM)
Your USB cable.
The firmware files.
Steps:
Remove battery, SIM card and micro SD card.
Open Odin on the computer.
Put the battery back in.
Plug in the USB cable to the phone.
Hold both volume up and down.
With VOL up/down held in, plug usb cable to the computer.
Your phone will show the beloved DOWNLOADING yellow image.
Odin:
Simply select the rom/firmware you want to flash to and enjoy.
I can confirm this will not overwrite the phone's internal 16gb storage, which is where most apps save backups to.
Future steps:
Before trying anything crazy, copy the entire phone internal 16gb storage to your computer. If you brick, you can always get a new captivate, copy the junk back and run a restore.
I recommend Titanium backup (donate the $6, the backup/restore is SUPER SUPER fast) along with Clockwork recovery. Clockwork's Nandroid makes full kernel backups and you can boot to recovery from the phone itself. No more adb reboot download or adb reboot recovery.
sorry for my english i have a 19000m the one from bell my phone boot with the GALAXY S LOGO WITH THE MUSIC BUT AFTER THAT BLACK SCREEN CAN I REPAIR THAT ?
Yes, odin is about your only hope here... Even if you boot into the bios and try to do a factory reset it will come up with error after error...
Reflashing will totally wipe and start fresh.
I am curious however. I think i isolated where my problem came from but I am still curious...
Did you try to sideload anything?
It happened to me twice with Bell's Vibrant version. The first time, just after one week after getting it (not rooted). They simply gave me a brand new one.
The second one took 3 week to go dead. Knowing my way around Linux Embedded systems, this time I investigated the issue. In recovery mode, there were error messages saying that the system could not fine the internal flash memory partitions. I could confirm from the kernel messages that partitions on internal sdcard had disappeared. I did factory reset, reflash original stock firmware with Odin, but it did nothing.
I Sent the phone back for repair and three weeks later, they gave me another one (probably refurbished!!).
My phone just turns on, with a black screen and the capacitive buttons lit up. Nothing else happens. When I try to go into download mode, it only goes back to this black screen. I does however detect that the phone is connected driver wise on the computer, but does not show up in Hemidall or Odin. I've tried just about everything
i used ODIN to resotore the phont to stock
but when it finsh...i get black screen
and the phone dose not work or do anything.
any help plzzz
isa.ahmed said:
i used ODIN to resotore the phont to stock
but when it finsh...i get black screen
and the phone dose not work or do anything.
any help plzzz
Click to expand...
Click to collapse
Does it light up or display anything and then go black, or does it just do nothing? If it does nothing, you're probably bricked, but try this anyway just in case your phone still has some life in it:
open Odin; press and hold both volume buttons and plug in your USB. If Odin lights up yellow, flash.
If that doesn't work, buy or build a jig, use it, and see if it goes into download mode. If it doesn't, plug the cable in anyway and see if Odin recognizes it. If it does, flash.
If that doesn't work, you're probably bricked. JTAG or Unbrickable Mod are your options from here, neither of which I personally know anything about but you can search around and find someone who can help you.
Hard Bricked= No signs of life, black screen no matter what, no response to USB plug in. Nothing but Unbrickable mod or JTAG will fix, I WOULD SUGGEST getting Unbrickable because you only have to get it once, and it cost the same as JTAG.
Soft Bricked= DL mode access is available(by jig or button combo and usb), recovery too, has some life in it. Can use ODIN/HEIMDALL to fix it.
when the flashing finsh and say done...and show the green light in the ODIN. the phone did not start up
dose this mean it break or dead charger?
as m not shure if the battery is full or not.
anyway i can pass the battery by over it with cuted USB cable?
isa.ahmed said:
when the flashing finsh and say done...and show the green light in the ODIN. the phone did not start up
dose this mean it break or dead charger?
as m not shure if the battery is full or not.
anyway i can pass the battery by over it with cuted USB cable?
Click to expand...
Click to collapse
If you got a green light, I would think it should at least turn on. However, if it was a successful flash, it should charge with the phone off. A bricked phone and a bad charger would both look the same: dead.
Try a different charger or battery if you think your battery could that dead. However if your battery died during your flash, that could also be the cause of your brick.
i charge the battery...and nothing happend
will the USB JAG solve it?
as i read in some post this will not
i need to send to some one to do it by opeing the phont it self
isa.ahmed said:
i charge the battery...and nothing happend
will the USB JAG solve it?
as i read in some post this will not
i need to send to some one to do it by opeing the phont it self
Click to expand...
Click to collapse
A jig is worth trying, but I suspect it will not solve your issue. You are correct, you need to send it to someone to have it fixed. Send a PM to AdamOutler or Connexion2005 and they can point you in the right direction.
what a crapy phone
i had Moto Defy and i never face same issue
so now am end with usellss phone..and need to theough away
what a waist of mony
isa.ahmed said:
what a crapy phone
i had Moto Defy and i never face same issue
so now am end with usellss phone..and need to theough away
what a waist of mony
Click to expand...
Click to collapse
You moto defy never flashed boot loaders since Motorola always had them locked down, and if you didn't know what you were doing flashing the stock Emma's that had boot loaders then it is not the phones fault. You should never really have to flash boot loaders and that is the ONLY risky part in flashing on these phones. Other than that Samsung cappys are almost TRUELY unbrickable (HARD BRICK) unless you mess up flashing boot loaders. WHICH YOU DID WHETHER YOU KNEW IT OR NOT BY FLASHING THE STOCK ODIN. SEND IT FOR UNBRICKABLE MOD, it is cheap repair and you WONT run into your same mistake ever again.
Sent from My KickAss CM7 Captivate
so no way i can do it here?
need to send it?to who i send? and who to trust?
i found some one will do for 50$
http://www.mobiletechvideos.com/blog/?page_id=776
Adam Outler
Sent from my SGH-I897 using xda premium
and other issue, i never toch the bootloader of it
i only re flash the OS of it only..and end with black screen.
this gay he will do what?
can the agent do it?
as it will be easer than to send it
can i have link of who will do it

My LG OB bricked? :(

hello everybody. i have problem... today i restart my lg ob after changing theme in nova script(i had nova v8) and after this restart phone does not goes to the system. Its restarts normal, i saw lg logo but after that, instead of bootanimation i saw black screen with blinking touch keys(menu, home, back, search). I pulled of battery for few seconds and put it back...turn on phone and...the same... :/ next i goes to emergency recovery and flash nova8 again and guess what? still the same!!!! after lg logo black screen with blinking touch keys! i tried to flash stock s/w with kdz updater, i tried 10a and 10e version and still the same! do u have maybe some other ideas how can i try to flash this that would maybe help me? or maybe i have to sent phone to service?
sorry for my english
Try factory-reset via recovery.
miticogirl said:
Try factory-reset via recovery.
Click to expand...
Click to collapse
but now i dont have nova or cwm recovery ;/
try hard reset (search for it )
Download LGMobile Update http://forum.xda-developers.com/showthread.php?t=1111771 in this Update Kit. Then turn of phone, pull of battery and press and hold Vol+ button and plug in USB and then in LGMobile Update click on "Custommer Support" and Recovery Phone. Write your IMEI and click check. It can take a lot of time because it will download a new firmware.
fatcobrah said:
try hard reset (search for it )
Click to expand...
Click to collapse
how can i do hard reset if my phone does not boot to system? i tried software recovery in lg mobile update but it does not helped too ;/
miticogirl said:
Download LGMobile Update http://forum.xda-developers.com/showthread.php?t=1111771 in this Update Kit. Then turn of phone, pull of battery and press and hold Vol+ button and plug in USB and then in LGMobile Update click on "Custommer Support" and Recovery Phone. Write your IMEI and click check. It can take a lot of time because it will download a new firmware.
Click to expand...
Click to collapse
yep..i've done this twice but no luck ;/
Send phone to service, they will change your mainboard or they will give you new phone.
yeaa..thought the same... thanks for answers !
dzynio said:
yeaa..thought the same... thanks for answers !
Click to expand...
Click to collapse
try with KDZ Updater...
dzynio said:
yep..i've done this twice but no luck ;/
Click to expand...
Click to collapse
nah, keep on holding that volume up then plug in the USB. have you installed the USB drivers?
Turn your phone off. Use eRecovery! Turn phone on then repeatedly hit Vol Down key then do factory reset. If no luck use KDZ updater.
gabwerkz said:
nah, keep on holding that volume up then plug in the USB. have you installed the USB drivers?
Click to expand...
Click to collapse
yes, i plug usb cable to device with holding vol+ and 'sw upgrade, please wait...' screen appear. I tried again few minutes ago with kdz updater and via lg mobile update phone recovery and no luck. Phone is rebooting (black screen with blinking touch keys) when installing software on 90% ;/ of course installing software goes to 100% and says its completed and ok, but phone reboots on 90% ;/. I have installed all drivers, i tried on my laptop (win7) and my dad (win xp).
dzynio said:
yes, i plug usb cable to device with holding vol+ and 'sw upgrade, please wait...' screen appear. I tried again few minutes ago with kdz updater and via lg mobile update phone recovery and no luck. Phone is rebooting (black screen with blinking touch keys) when installing software on 90% ;/ of course installing software goes to 100% and says its completed and ok, but phone reboots on 90% ;/. I have installed all drivers, i tried on my laptop (win7) and my dad (win xp).
Click to expand...
Click to collapse
it's normal reboot on 90% and next go to 100%, i do that with windows XP and work...
fortunat0 said:
it's normal reboot on 90% and next go to 100%, i do that with windows XP and work...
Click to expand...
Click to collapse
so maybe its normal, but really...i've tried a couple of times with kdz and phone recovery by lg mobile and still the same, black screen, blinking touch keys. And i dont have eRecovery any more beacause i flashed stock s/w but it dont work ;/
that's a big hello of a problem.... I jonno what else u can do... if I were u then I would flash it again and again... then maybe for the customer care center... although I think ur warranty is being voided so u will not be able to repair it for free... let's hope for the best and let us know what happens next... best of luck...
Przykro ki kolego, nie naprawisz tego sam. Musisz odeslac telefon do serwisu LG w Mławie...
Sorry pal, you can't fix it yourself. You must send it to LG service centre in Mława (Poland)...
Sent from my LG-P970 using XDA Premium App
shourov said:
that's a big hello of a problem.... I jonno what else u can do... if I were u then I would flash it again and again... then maybe for the customer care center... although I think ur warranty is being voided so u will not be able to repair it for free... let's hope for the best and let us know what happens next... best of luck...
Click to expand...
Click to collapse
+1 for this. Flash and flash. Try upgrading to V10E via KDZ. Me thinks it's a bootloader problem. Does LG SECURITY TEAM appears or not?
Sent from my LG-P970 using xda premium
yeah..i flashed this several times...with kdz updater and by lg mobile update->phone recovery. I flashed 10A and 10E...results the same. I dont know how LG SECURITY TEAM looks like but i didnt see anything else besides LG LOGO--> Black screen with blinking touch keys and just Black screen with blinking keys (even without lg logo). I give up with this, there is no hope for this phone i think, today im sending this to the service. Thanks for helping me i will certainly write here what happend if i get phone back
I also stuck on the same thing
Really for that reason i hate LG Black

Screwed the pooch totally this time..

Not sure how I did it, but I am stuck at the Red LG logo with the white LG letters and my phone will go no further. It will not shut down without a battery pull. I have tried to do the hold down volume and factory reset the phone, same screen pops back up. Plugged in does nothing either. It is like it lost the ability to boot.
I ask here for maybe some guidance from a dev. If wrong place, please move it.
I can not get into the recovery, regular boot, computer to recognize it.. Nothing at all... Is there an actual boot image to put on the sd card to boot to?
Any suggestions??
eghill1125 said:
Not sure how I did it, but I am stuck at the Red LG logo with the white LG letters and my phone will go no further. It will not shut down without a battery pull. I have tried to do the hold down volume and factory reset the phone, same screen pops back up. Plugged in does nothing either. It is like it lost the ability to boot.
I ask here for maybe some guidance from a dev. If wrong place, please move it.
I can not get into the recovery, regular boot, computer to recognize it.. Nothing at all... Is there an actual boot image to put on the sd card to boot to?
Any suggestions??
Click to expand...
Click to collapse
What did you do right before this point?
I think my mistake was going into Rom Manager to see if I had anything showing clockwork installed. Phone restarted and i was at this point since. Not sure if I told it to update a clockwork or not. Head is fried now from messing with it..
eghill1125 said:
I think my mistake was going into Rom Manager to see if I had anything showing clockwork installed. Phone restarted and i was at this point since. Not sure if I told it to update a clockwork or not. Head is fried now from messing with it..
Click to expand...
Click to collapse
Ok, I can get you fixed but I can just about promise you that you will be in test mode,
I don't own this phone (almost did) but curious, how Wood you fix that? Does LG have a tool like rsd lite (moto) or odin4 (sammy) ?
Sent from my DROID RAZR using Tapatalk
Try this: http://forum.xda-developers.com/showthread.php?t=1337386
I looked at that thread, but I can't see how I would go about that when I can not get anything on the phone beside the LG logo. I can't plug it in and select internet connection or install any software drivers from the phone on the first line. I have called Verizon and they are sending me out another phone, but I would like to get this one fixed if I can..
eghill1125 said:
I looked at that thread, but I can't see how I would go about that when I can not get anything on the phone beside the LG logo. I can't plug it in and select internet connection or install any software drivers from the phone on the first line. I have called Verizon and they are sending me out another phone, but I would like to get this one fixed if I can..
Click to expand...
Click to collapse
You can get into emergency mode to flash the tot file in lgnspt.
1 Pull Battery
2 Press and hold volume up + power
3 Plug phone into computer (while still holding buttons)
4 Put battery back in (while still holding buttons)
5 You should now enter emergency mode
Can u enter CWM? By holding down pwer and vol down. Then confirm data wipe (it won't) then reboot into cwm? If u can try to install a rom
Sent from my ADR6425LVW using xda premium
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums & Read the Forum Rules
Moving to General

[Q] Bricked ! nvflash not work.

Need help.
My optimus 2x seem to be bricked.
nothing shown at the screen. (just blank)
i can't enter the cwm.
smartflash also cannot detect my phone.
I try to use nvflash but it stuck at "waiting for bootloader to initialize"
anything i can do to revive my phone ?
or is it totally bricked ?
Hi,
Congratz for being the first person I ever read on o2x thread whom actually 'succesfully' bricked his phone. I've been here since o2x thread was born..alot of ppl use the term 'bricked' loosely but hasn't actually really bricked their phones.
If you lost ADB, Fastboot, unable to Nvflash/Smartflash... your phone is, sad to say, gone.
Anyway, I really hope you can share what you did to eventually get into this state, atleast you can help others to prevent bricking their o2x.
Thanks.
Well congratz, now move to something that is properly supported
Sent from my Optimus 2X using XDA
Haha.
can I get medal for this "achievement" ?
I bought it as faulty phone around usd 16. so I don't know what happen to it.
Ouh...usd16.. pretty useful for spare parts.
If you bought it for 16 dollars then I would advise you to sell the phone for spare parts. Even the glass costs 20 or more dollars.
Sent from my Optimus 2X using XDA
hmmmm, dudes, idk if im right buuuuuuuuuut... happened to me, i thought it was completelt dead, when after all i found out that my pc didnt recognise my lg o2x as an apx platform so it would always fail, sooooo, i did it on my sisters pc which never had lg drivers and i resurected my phone id advise to try it...
---------- Post added at 11:38 PM ---------- Previous post was at 11:35 PM ----------
ohhh, long story short and translated, if you have ever installed lg drivers on your pc, forget about it being recognised as an apx platform, even if you uninstall all lg software
1.From PC,manually place Stock LG Rom(V20Q.zip or [?]) on Your SD card then reinsert in phone.
2.Don't connect phone to PC or power (AC)
3.pull the battery out and reinsert it( now connect power (AC)
Hold the Volume Down button (keep pressed!!) then press and hold the Power button until the device turns on and you see the recovery menu
4.then proceed as you normally would meaning install .zip from SD card
Hope it helps
-JAZZMAN- said:
1.From PC,manually place Stock LG Rom(V20Q.zip or [?]) on Your SD card then reinsert in phone.
2. pull the battery out and reinsert it
Hold the Volume Down button
(keep pressed!!) then press and hold the Power down button until the device turns on and you see the recovery menu
3.then proceed as you normally would meaning install .zip from SD card
Hope it helps
Click to expand...
Click to collapse
dude O_O
he said the phone wont even load recovery O_O
skylinegt77 said:
dude O_O
he said the phone wont even load recovery O_O
Click to expand...
Click to collapse
Yes,I read that, But neither would mine after using ext3 converter without backup!
So after eating a big bowl of "BOOTLOOPS" I utilized the phones hard reset mode thinking It would lead to a factory reset but instead got the CWM recovery menu
after which I flashed and Voila 0_0
Also "DUDE" at least I'm trying to offer help instead of joking about such a serious concern...I guess... well only maybe when it's your phone and you have no answers<---this looks better
-JAZZMAN- said:
Yes,I read that, But neither would mine after using ext3 converter without backup!
So after eating a big bowl of "BOOTLOOPS" I utilized the phones hard reset mode thinking It would lead to a factory reset but instead got the CWM recovery menu
after which I flashed and Voila 0_0
Also "DUDE" at least I'm trying to offer help instead of joking about such a serious concern...I guess... well only maybe when it's your phone and you have no answers<---this looks better
Click to expand...
Click to collapse
You should really read again OP, it can't load bootloader.. So it can't boot to anything as bootloader is the essential part of the phone that loads after either recovery partition, or /boot Android one.
aris.syah said:
Need help.
My optimus 2x seem to be bricked.
nothing shown at the screen. (just blank)
i can't enter the cwm.
smartflash also cannot detect my phone.
I try to use nvflash but it stuck at "waiting for bootloader to initialize"
anything i can do to revive my phone ?
or is it totally bricked ?
Click to expand...
Click to collapse
Just to check: are you sure to boot the phone in Apx mode? Battery off, volume up pressed, then plug AC ?
Striatum_bdr said:
You should really read again OP, it can't load bootloader.. So it can't boot to anything as bootloader is the essential part of the phone that loads after either recovery partition, or /boot Android one.
Click to expand...
Click to collapse
Once again, I know and understand!!!!!
New to LG but not to how this process works so please stop with the "Dear N00B"
responses
I was only offering a suggestion that maybe wasn't tried even if proven futile!
also, for the most part, the days of "bricks" are pretty much over so there is always the slimmest possibility for hope. Wouldn't you exhaust every possibility....
Anyway,enough said on this I hope that he finds a solution
hi there,
N00B here...i had this kind of problem too...my laptop still recognize it as nvidia bootloader for mobile device AKA APX driver, but it never flashed in the nvflash way...
holding volume down and insert charging cord also give me nothing...

[Q] Have I managed to HARD-BRICK my phone?

Switched from one provider to another, got a new phone which uses micro-sim, and couldnt get the p880 to read the new sim card, so I have been using the new phone, which is greatly inferior to the p880..
With the p880 just sitting around unused, i decided i might as well try to mod it, then get a regular sim card for it and start using it again. I think i killed it instead.
Before it died on me, I formatted / wiped / factory reset and then used the LG Mobile Support tool to upgrade to whatever the newest official release was.. 4.1.2??
At this point, here is what it can do:
1) When attempting to just turn it on and USE it as normal, it turns on, gets to the animated LG logo and stays there forever.
2) Power + Vol Down = OEM LG recovery menu
3) Power + Vol Up = Some kind of Restore graphic
4) Power + Vol Up and Down (AVX) = nothing
5) Plugged into USB with battery removed and holding Vol Down = home row LEDs light up, nothing else
Windows sees the phone as a "removable disk H:" when I plug it in, but the LG recovery software does not see it, and it also does not show up in the device manager..
At this point, all that I can seem to access is the "apply update from ADB" option to do an "adb sideload" command in recovery mode.. When I send over the root tool, the phone is happy. If I attempt to send anything else over via sideload, I always get kicked out of the process when it gets to the "verifying installation package" portion. I can wipe / factory reset to my heart's content, but I can get absolutely no further than this after attempting for about six hours yesterday.
Any hope for me or do i have a dope looking paperweight? Will providing you guys either the IMEI or S/N shed any light into a path to recovery?
Thanks for your time!
You have a booting rom, the device is not even close to hard brick. Is your bootloader unlocked? If yes you can flash a custom recovery with fastboot and install any rom you want.
Sent from my OmniROM-powered LG Optimus 4X HD
@one30six
Use this thread http://forum.xda-developers.com/showthread.php?t=2069723 or
Use this thread http://forum.xda-developers.com/showthread.php?t=2179126 to recover your phone.
Read the instructions with care and act as stated.
Good Luck.
sPEADy said:
@one30six
Use this thread http://forum.xda-developers.com/showthread.php?t=2069723 or
Use this thread http://forum.xda-developers.com/showthread.php?t=2179126 to recover your phone.
Read the instructions with care and act as stated.
Good Luck.
Click to expand...
Click to collapse
thank you, speady.. it turned out to be the first solution that you suggested, which i had seen before during my scouring of these forums.. but the real basis of my problem was that i had my phone plugged into the front-facing USB port of my computer rather than the one directly connected to the motherboard (on the back).. i guess the phone wasnt getting enough juice out of the front port to boot to S/W Update mode.. i am back to stock LG software and am eventually going to mod to another ROM
THANK YOU!

Categories

Resources