Database Develop

[Q] Restoring Captivate from AT&T World Phone Screen

Hey folks. I'm hoping to get through this in one piece, with one walkthrough.
I recently messed up in flashing a Rom to my Captivate. It cleared the phone of firmware and left me with the AT&T splash screen.
I bought a jig, and am now at the "Downloading..." screen and am trying to take this slowly to ensure a properly functioning phone (I've been without for two weeks now).
I've read through the sticky post [link]http://forum.xda-developers.com/showthread.php?t=884364[/link] and have most of the downloads. The Odin link is dead, and I don't have the proper version (I used a version I later found out was bad).
What I'm hoping for is to get someone to show me where the proper version of Odin is, and maybe give me a quick guide to doing this for a Rogers Galaxy S Captivate.
I hope I'm not coming off as lazy, but I tried this solo, and it went awry. Thanks for any help in advance.

This is the link for Odin. http://forum.xda-developers.com/showthread.php?t=731989
You want to Open Odin, then use the jig to put the phone in download mode, connect usb to your computer and wait until odin recognizes your phone. Click Start and sit back and wait. You should then be able to put whatever rom you want on the sd card and flash

Okay. I got the proper download, and used Odin. It reported success.
I haven't unplugged the phone from the computer yet, but it's also not showing as a drive on my computer. I'm at the stage where I'm supposed to root the phone after using Odin and before flashing.
Should I unplug the phone, or is that going to send me back to square one?

JavaMac said:
Okay. I got the proper download, and used Odin. It reported success.
I haven't unplugged the phone from the computer yet, but it's also not showing as a drive on my computer. I'm at the stage where I'm supposed to root the phone after using Odin and before flashing.
Should I unplug the phone, or is that going to send me back to square one?
Click to expand...
Click to collapse
If you used that Odin 1 click you will have the AT&T version, it will work but you will have the AT&T boot up screen. After it is finished your phone should reboot by itself. If it didn't try pulling the battery and then turn it back on.

Driver Installation Issue at Fault?
Okay, so I'm starting to wonder what's going on with the communication between my phone and my computer. I have the drivers, but when I try to install them (64 bit, for a dual-core, right?), it claims to fail.
I think maybe that this is the reason I can't get the computer to recognize the drive. Also, when plugged in last time, it said it failed to install drivers again. Even when the phone was operational, I had issues with that.
So . . . I'm wondering if maybe I solve that and the issue becomes seamless. Any thoughts on this would be appreciated, as it seems I'm stuck until I get the phone to register. Even Odin won't see it now, although I've already passed that step. F-Bomb.

Did you get the drivers right from samsung web site if not thats why they wont install i had same thing when i got my cappy.
I got drivers from.samsung.com installed em worked perfect sence. i kept the download saved had to install em a few times over the last 9 or so months. Only because of all the dam software hardware i run. Good luck
Sent from my GT-I9000 using XDA App

Just because it's a dual core processor in the computer doesn't mean you have a 64 bit OS.
You might want to know what version of windows you have...just a thought.

Okay . . . I can't seem to resolve this driver problem, nor can I move forward in the previous issue of getting my phone back to a functional state.
I can't imagine what I'm doing wrong that everyone else managed to avoid. Could I maybe request some one-on-one time with an experienced Rogers user? Just to recall the exact steps they took in order to successfully UNSCREW their phone.
Again, I appreciate all the help. Every post is making progress. I'm just frustrated at my ineptness with solid state installations.

I'm still not able to install the drivers or get my computer to register the phone as a drive. I did a bit more reading, but I've found nothing but different driver links. Has anyone else had this installation failure?

I have had driver problems before...try plugging up phone; on computer control panel, device managment , go to were it has device (just click then till se something about samsung) then uninstall drivers, next unplug phone, reinstall drivers that are on design gears (developer) thread for odin one click, next plug up phone sbf it will say new hardware and install drivers then see if that works... Ps if need to just pm me and I will get back to you to try and help
Sent from my SAMSUNG-SGH-I897 using XDA Premium App

A side note: I just tried it from my computer and the link if good and they work
Sent from my SAMSUNG-SGH-I897 using XDA Premium App

Try it again, however this time plug your USB cable into the USB port in the back of the computer.

Drivers were installed properly with Toolbox. Thanks for the help

[Q] One Click Unbrick questions

I have done the unfortunate thing and bricked my phone, now I did see a post in here on this subject but I am not able to open this program/app on either Ubuntu or Windows 7 PC's.
Now my questions...
Is this the only way to unbrick my phone?
Using Linux or Windows, which one works better?
I am using the Rogers one i896, the screen just stays at i896. I will explain what I was trying to do, I had installed Clockworkmod on my rooted phone on the intentions to install another ROM on my phone. I boycotted this idea as I saw another way that had me download the zip, enable debugging, turnoff and place into recovery mode...that is where I got stuck. I obviously made a mistake somewhere, does anyone have any ideas how to unbrick my phone. Not too make it sound worse but I have to use my wife's old Blackberry...a pink flip!

Linux works better. After dl, right click, permissions, check the little box that says make it executable. Click ok. Now right click on it, open with java (either open jdk, or sun java ). The app should open.

Thanks very much, I was now able to install on Linux but after all this the unbrick did not work. It tells me to plug my phone in, the phone is in the USB port it has always been in. I turned the phone in the off position and all it does is show a load symbol similar to the one before the battery charge comes on, when it goes on it just stops at the i896 screen and does nothing else. Any other ideas on how to unbrick this phone? or am I done and got to get a new one? I'd rather keep this one

Ok not to say nothing is working, but I have a yellow triangle with Android digging, says downloading below and at the bottom do not turn off target!!! What does this mean?

coltiger said:
Ok not to say nothing is working, but I have a yellow triangle with Android digging, says downloading below and at the bottom do not turn off target!!! What does this mean?
Click to expand...
Click to collapse
Plug it into the computer and hit the button.

I tried that but my pc doesnt pickup my Samsung anymore, it is like it doesnt exist when I plug in. I am gonna reboot the PC and retry.

Are you using a Linux machine?

yes I am I have Ubuntu 11.10 installed, I never had this trouble before with it recognizing the phone.

If you can get download mode, flash back to stock.

It goes into download mode but not sure how to flash to stock

There is a sticky in the development section for stock ROM.

http://forum.xda-developers.com/showthread.php?t=1285616

Thanks guys, I have read the instructions and all is fine except that I am using Rogers version i896, if it doesn't make any difference then I will load the AT&T if there would be issues. Second issue I am running into is while my phone goes into download mode, my PC's continue to not see my phone, I have removed everything including the SD card. Any ideas how to get the phone to be recognized as I think this would solve a lot

My friend recently had similar problems and it turned out to be a bad cable. Don't overlook the obvious.
/e
Sent from my SGH-I897 using xda premium

Help with Soft brick! Edited with "MY" solution!

Before ppl start asking me, this is what happened. I gave my Cappy to my daughter and after months of running Dlev Rom, I decided to upgrade to ICS. She was not happy with the rom and wanted to go back to gingerbread. I tried downgrading via recovery but had issues with the downgrade. Long story short....ignorant me, I used Odin and end it up with eclair.
Now here is where the problem started. The phone was succesfully flashed with eclair but button combo wasnt working at all. So, I rooted first and then with adb, I adb reboot download, then once in download, I flashed ginger bootloaders and thats how i end it up with the infamous phone /!\ comp. soft brick. Since originally i had no button combo working, I cant get into download mode. My comp just wont recognize the Cappy.
I have searched for hours and tried all ways possible to get into DL mode but "nada"! Even with Odin opened or heimdall, batt out, batt in, all combinations of buttons...nada (nothing), no luck. Also tried the program by Adam to unbrick the Cappy (that I've found searching) but still nada! I have windows 7 with java and that program by Adam just wont work on my comp.
Can someone try to help me on what can I do without sending my daughter's Cappy to a shop...lol?
Edit: In this post I explain what got "me" out of the softbrick after 2 days of trying! It might not work for who ever falls in a similar situation and even mayb is not a proper way of doing things, but it worked on my end!!! http://forum.xda-developers.com/showpost.php?p=26305016&postcount=23

You can use that screen as a download mode.
Remove Java. And then go download Java JRE.
Java JRE 32 bit
Java JRE 64 bit
Try going and grabbing the Heimdall KK4 1 click. Or you could try any of the Gingerbread Heimdall packages in the OneClick Master Collection
I think you'll be fine to run Heimdall after the Java reinstall.

Red_81 said:
Try this:
Take out battery
Plug in usb cable
Hold volume+ and volume-
Pop in battery
This should take you straight into download mode. Just have to flash a new ROM/Stock Image
This came from another post about 10 down from yours.
Click to expand...
Click to collapse
Lol....Trust me, I've done that and all ways possible. At least the phone isnt hard bricked. All i need is DL mode and I should be good! Thx sweety!

Baby Liz Sandra said:
Before ppl start asking me, this is what happened. I gave my Cappy to my daughter and after months of running Dlev Rom, I decided to upgrade to ICS. She was not happy with the rom and wanted to go back to gingerbread. I tried downgrading via recovery but had issues with the downgrade. Long story short....ignorant me, I used Odin and end it up with eclair.
Now here is where the problem started. The phone was succesfully flashed with eclair but button combo wasnt working at all. So, I rooted first and then with adb, I adb reboot download, then once in download, I flashed ginger bootloaders and thats how i end it up with the infamous phone /!\ comp. soft brick. Since originally i had no button combo working, I cant get into download mode. My comp just wont recognize the Cappy.
I have searched for hours and tried all ways possible to get into DL mode but "nada"! Even with Odin opened or heimdall, batt out, batt in, all combinations of buttons...nada (nothing), no luck. Also tried the program by Adam to unbrick the Cappy (that I've found searching) but still nada! I have windows 7 with java and that program by Adam just wont work on my comp.
Can someone try to help me on what can I do without sending my daughter's Cappy to a shop...lol?
Click to expand...
Click to collapse
The [Phone /!\ Computer] screen is another method of Download Mode. You should still get Odin to recognize the phone. If Odin recognizes the phone, you should flash KI2 from This thread, since it has CWM injected. Once you have CWM, you have a clean slate to install any ROM you desire.
If Odin does NOT recognize you phone no matter which USB port you connect the phone to (as it happened to me once), you could try what I did. I downloaded Windows installer for Ubuntu Desktop, and that got me Linux. Once I had Linux, flashed KB2 from the ROM thread linked above. Why Linux? Because I never got Heimdall to work on Windows, but I did on Linux. After my phone was completely stock, I followed the instructions on TRusello's Guide to Flashing ANY ROM to get my phone set up the way I wanted.
I'm sure there are faster ways than the one I just gave you, but I can vouch that my method works, and you might get your phone sorted out while you wait for a better response. Good luck!

That will teach me to edit my post without refreshing first!

kafepuya said:
The [Phone /!\ Computer] screen is another method of Download Mode. You should still get Odin to recognize the phone. If Odin recognizes the phone, you should flash KI2 from This thread, since it has CWM injected. Once you have CWM, you have a clean slate to install any ROM you desire.
If Odin does NOT recognize you phone no matter which USB port you connect the phone to (as it happened to me once), you could try what I did. I downloaded Windows installer for Ubuntu Desktop, and that got me Linux. Once I had Linux, flashed KB2 from the ROM thread linked above. Why Linux? Because I never got Heimdall to work on Windows, but I did on Linux. After my phone was completely stock, I followed the instructions on TRusello's Guide to Flashing ANY ROM to get my phone set up the way I wanted.
I'm sure there are faster ways than the one I just gave you, but I can vouch that my method works, and you might get your phone sorted out while you wait for a better response. Good luck!
Click to expand...
Click to collapse
Yeeee....finally someone with a good heart and willing to share knowledge!!! And BTW, yes I tried all usb ports. The difference between your comp and mine is that I can run heimdall but like I said, way i plug the usb, my comp nor heimdall and/or Odin recognize the phone after the brick.
I'm not home at the moment but thank you from the bottom of my heart for your info. I'll get home kind of late tonight but I will follow your info to the tee and keep u post it...if u dont mind!
Thx and a kiss for you sweety!
Sent from my SGS II 4G using XDA Premium App

Heimdall and odin use different drivers, Once you install Heimdal and use your phone on a USB port, that USB port will only work with Heimdall. Odin will no longer work on that USB port, Until you uninstall the heimdall drivers

TRusselo said:
Heimdall and odin use different drivers, Once you install Heimdal and use your phone on a USB port, that USB port will only work with Heimdall. Odin will no longer work on that USB port, Until you uninstall the heimdall drivers
Click to expand...
Click to collapse
Short and sweet...i installed ubuntu last night on my pc and I thought i lost windows. Did some search and I can choose when my pc start up either W7 or ubuntu. Went to bed at 4am trying to install java to ubuntu with no luck. To b honest, i'm about to quit trying to get this phone in DL mode. My daughter hates me and my husband told me, u messed it up...u fix it! Agh!!!!! I'm trying again but if I cant get it to work I rather just buy my kid a new phone....and thats a shame because that Cappy has been a warrior!
Any other method to get DL mode??? PLEASE...SOMEONE????

Once you're at that screen, it is download mode. You could try a jig. You can build one or buy one.
Did you reinstall java on Windows 7 and then try Heimdall?

Red_81 said:
Once you're at that screen, it is download mode. You could try a jig. You can build one or buy one.
Did you reinstall java on Windows 7 and then try Heimdall?
Click to expand...
Click to collapse
Yes I did and pc still not recognize device. Tried all ports and different usb cable...still no go!

Did device manager not recognize it or Odin/Heimdall not recognize it? I know my system wouldn't show it was connected but Odin/Heimdall still would.

Red_81 said:
Did device manager not recognize it or Odin/Heimdall not recognize it? I know my system wouldn't show it was connected but Odin/Heimdall still would.
Click to expand...
Click to collapse
Neither one recognize the device. With Odin you're supposse to see the yellow light meaning its connected...but nothing, and with heimdall clearly says disconected. I am sooo exausted looking for an answer as to what to do to get this phone on DL mode! I've used both programs in the past but the phone just dont want to come alive!

I understand how frustrating it can be to get a phone to respond.
I went back to your first post to make sure I didn't miss anything and I realized what the issue might be. Since the phone was upgraded to ICS it wouldn't be using the standard captivate drivers any more.
Let's try this:
Download and install the Android SDK
Add the Google USB Driver
Try ODIN/Heimdall again.
I think I had a similar issue when I was reverting a phone from CM7 back to Stock captivate.

Red_81 said:
I understand how frustrating it can be to get a phone to respond.
I went back to your first post to make sure I didn't miss anything and I realized what the issue might be. Since the phone was upgraded to ICS it wouldn't be using the standard captivate drivers any more.
Let's try this:
Download and install the Android SDK
Add the Google USB Driver
Try ODIN/Heimdall again.
I think I had a similar issue when I was reverting a phone from CM7 back to Stock captivate.
Click to expand...
Click to collapse
Oookkkk...will give this a try! Thank you.

Baby Liz Sandra said:
Oookkkk...will give this a try! Thank you.
Click to expand...
Click to collapse
I think it will work. Sorry it took so long for me to realize it. I actually had to do the same procedure within the last week but less sleep + work + cold is making me a little foggy.

Red_81 said:
I think it will work. Sorry it took so long for me to realize it. I actually had to do the same procedure within the last week but less sleep + work + cold is making me a little foggy.
Click to expand...
Click to collapse
Just finished installing both...restarting pc now and will report back. Thank you yet again!

Baby Liz Sandra said:
Just finished installing both...restarting pc now and will report back. Thank you yet again!
Click to expand...
Click to collapse
Ok...thats it! That did not work either. I connected my SGS II just to see if my pc would recognize the phone, and indeed my pc picked up the device as well as my husband's Sensation. So thats it! Just called Radio Shack for a jig and the guy never heard of that...lmao! You guys should see my daughter's look at me....awh!
Anyway...I'm subscribed to this thread so if anyone has another bright idea I'll give it a shot. Thanks again!

Sorry that didn't work either. Here's another thread about connection issues to the computer. I hope this helps
http://forum.xda-developers.com/showthread.php?t=1351224

Red_81 said:
Sorry that didn't work either. Here's another thread about connection issues to the computer. I hope this helps
http://forum.xda-developers.com/showthread.php?t=1351224
Click to expand...
Click to collapse
Well...thank you! Don't know if i should keep DLing stuff to my pc. Now I have ubuntu, sdk manager, hemidall, dont know how many odins, etc. My husband just ask me for a new pc because he tried to uninstall ubuntu and he was unsuccesfull at it. Now this softbrick is gonna cause me some major issues family wise. This really sucks! But hey, me been a female, I just learned that nothing is impossible for us. If my hubbie dont wanna help me...I'll get it done one way or another. I will see my daughter smile....believe that!!!!!
Thank you!

I have a 2.5 year old daughter and would do anything to see her smile.
Here is a guy here on XDA who makes the jigs. However, I still believe you just have a driver issue. At this point I can only say to take off all the drivers, odin, and heimdall and start fresh.
http://forum.xda-developers.com/member.php?u=500006
I used his kindle fire cable and it was great.

[Q] i9000 boots to black screen NO DOWNLOD MODE OR RECOVERY

Ok so I purchased an i9000M that was advertised as broken (got it for cheap) to see if I could get it going for my step daughter. I turn it on.... I get the samsung boot screen and goes black when it should be booting OS.
Windows still recognizes it somewhat. If I look in device manager under "portable devices" It shows a "j" and "k" drive that are identified as i9000 and i9000 sd or something like that. Although Windows sees it.... It wont mount these drives unfortunately.
Things I've tried ( Before someone suggests I use a JIG............. It doesn't and will not work on this phone)
USB JIG (tested and working on my Hercules)
SD Card Partition (EXT4 and FAT32) because I suspect borked internal storage
SD Card Partition (ReiserFS and FAT32) Still nothing......... then I realized the phone probably wasnt rooted
3 button combos ( every single combination) nada
plugging in USB cable while holding volume up and down...
ADB Reboot recovery/download ( not recognized because I cant turn on debugging)
ETC ETC ETC........
I have been searching google for hours for some kind of clue as to what can be done other than JTAG repair and All I come up with (no matter what site im on) is " Use a USB JIG" duhhhh Its getting rather annoying.
Im no stranger to flashing ( no expert) but this one has me stumped. I was considering buying a RIFFbox anyways but I thought maybe some experienced users out there might be able to suggest something.
My hope is that something can be done with the J and K drive that was mentioned. Perhaps I can format and somehow push a rom straight to the internal storage without any assistance from the phone itself...... I know..... wishful thinking. or perhaps boot straight from external SD???? That would be interesting!
More to this.... I realize this question has probably been asked a million times because it seems to be a common issue on this phone but I suppose my long winded question really boils down to my last paragraph which I havent seen suggested yet.
EDIT: I have a Windows 7 AND kubuntu 12.04 dual boot if any suggestions require linux
Any help would be greatly appriciated.

kibosh1981 said:
Any help would be greatly appriciated.
Click to expand...
Click to collapse
My Android Solutions should get you started but FIRST ensure your battery is no malfunctioning and Battery contacts are good and not loose.

xsenman said:
My Android Solutions should get you started but FIRST ensure your battery is no malfunctioning and Battery contacts are good and not loose.
Click to expand...
Click to collapse
Thanks. i will have a look and experiment tomorrow.
I'll report back my progress

if it pops up when you plug it into the computer, check if it does in odin. if does in there too try to flash a stock rom. or better yet take this download and follow the read me intructions, except the dl mode part cause you said it doesnt work. try both with the phone on and off. no it isnt the bell version of the pom but it will work. you will problably want to root it then install galaxy s unlock tool from the market and use that to unlock the phone aswell.(cause it not the bell rom)
http://www.mediafire.com/download.php?34oxweahfpy53dj

taz0697 said:
if it pops up when you plug it into the computer, check if it does in odin. if does in there too try to flash a stock rom. or better yet take this download and follow the read me intructions, except the dl mode part cause you said it doesnt work. try both with the phone on and off. no it isnt the bell version of the pom but it will work. you will problably want to root it then install galaxy s unlock tool from the market and use that to unlock the phone aswell.(cause it not the bell rom)
http://www.mediafire.com/download.php?34oxweahfpy53dj
Click to expand...
Click to collapse
As I mentioned.... no download mode, therefore.... No ODIN. Unless someone has some magical way to make it work otherwise. The computer knows its an I9000 at least. Kies says its in the wrong mode and I have no UI so debugging is out of the question.
Also: Xsenmen. I was unable to get any of the tools to connect. In one section you mention that AndroPlatina attempts to connect while booting? I was unable to get this to happen. I even tried the "heat trick" to no avail

[Q] Help Stuck

Ok to start off with I got this phone(Captivate) off one of my friends he has no idea what happened to it and I need help someone who knows what to do and how to do it.
I have tried everything
When I try to turn it on it just stays on the At&t screen
Phone will not connect to computer ( I have download all the correct drivers)
I have tried odin, Kies, it all.
It will go in to downloading and recovery mode.
But phone will not connect to computer any computer at all I have tried at least 10 different computers.
Any one at all got any idea how to fix this.
and sorry for posting or making a new thread I just didn't know where to put it.
Thanks guys. :cyclops:

darkstream83 said:
Ok to start off with I got this phone(Captivate) off one of my friends he has no idea what happened to it and I need help someone who knows what to do and how to do it.
I have tried everything
When I try to turn it on it just stays on the At&t screen
Phone will not connect to computer ( I have download all the correct drivers)
I have tried odin, Kies, it all.
It will go in to downloading and recovery mode.
But phone will not connect to computer any computer at all I have tried at least 10 different computers.
Any one at all got any idea how to fix this.
and sorry for posting or making a new thread I just didn't know where to put it.
Thanks guys. :cyclops:
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1953930 Check out that link. If you can get into download and recovery then a computer should recognize it in some form. Whether it sees it as the cappy it is or some unknown device it should still see it. However if it doesn't see anything at all you have a bad connection somewhere.

m1batt1 said:
http://forum.xda-developers.com/showthread.php?t=1953930 Check out that link. If you can get into download and recovery then a computer should recognize it in some form. Whether it sees it as the cappy it is or some unknown device it should still see it. However if it doesn't see anything at all you have a bad connection somewhere.
Click to expand...
Click to collapse
Thanks so much im going to try it right now.