Database Develop

Help me please...galaxy tab Exclamation mark

i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....

water30 said:
i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
Click to expand...
Click to collapse
what did you do to get to this screen? Is this after or before you upgraded firmware?

GANJDROID said:
what did you do to get to this screen? Is this after or before you upgraded firmware?
Click to expand...
Click to collapse
after upgrade firmware odin show reset but the my tab not reset then i just manual reset (i can take this method for my galaxys ) after that.....

Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again

i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?

primeroz said:
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
Click to expand...
Click to collapse
Read my above post. Go into download mode (volume down + home + power) you'll still have the same image but the phone WILL be in download mode. Then flash your previous firmware and you're sorted.
Sent from my GT-P1000

You probably got that by messing with the kernel. Fund the zImage from the firmware, extract it with a .tar extractor then use something like heimdall to flash the kernel and it should work.
Sent from my GT-P1000 using Tapatalk

Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.

Help please
slaia said:
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Click to expand...
Click to collapse
Having the same problem too... anyone can help?

If you see Phone-!-Pc on the Tab screen it is the download mode.
You can reflash it using Odin, however, you will need to do full Rom flash. I had similar problem and solved it by replashing.
I followed the latest guide published in this forum and Roto-JME rom with reformatting of internal sd.

Phone ! PC error FML!!!
GANJDROID said:
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
Click to expand...
Click to collapse
Where can i download the JM6 zip??

Hey guys,
I tried to manually update my tab to Gingerbread today via Odin, but it kept hanging on select partition (I discovered I used the wrong PIT for the firmware I was going to flash, but as I didn't select the firmware yet that shouldn't be a problem). At last I decided to quit Odin (which might have been stupid...) and try it again. Then it kept haning even earlier, so I tried to restart the device in download mode. However, whatever I try it keeps giving the Phone ! PC sign. If I try to just boot, if I try to go into recovery mode or if I try to go into download mode. I saw a lot of possible ways to solve the problem, but my PC doesn't recognize the tab anymore. If I connect it, it does give the "usb device connected" sound, but there is a popup which sais "USB Device not recognized. One of the USB Devices attached to this computer has malfunctioned and Windows does not recognize it. For assistance in solving this problem, click this message". I already tried to reinstall the driver but it doesn't work. Also Odin and Heimdall don't detect any device.
Does anyone know a solution for this problem? Maybe taking the battery out? (for which I have to buy a new triangle screwdriver, so I need to know if it could possibly work first. It takes some weeks to order such a thing I think...)
EDIT: I played around a bit with the drivers again, and suddenly both Heimdall and Odin recognized it. However Odin stopped recognizing it again. Then I pressed "read PIT" in Heimdall, which worked. After that the device started booting up to the Samsung logo animation and then powered off again. Now it doesn't do anything anymore, not even showing the Phone ! PC screen. I'll charge it overnight (maybe it's gone empty during the process), so I hope that helps.....

In some strange way, the phone works again..... So never mind my post above.

[Q] How to go back to standard firmware?

Hi,
was very interested in rooting my phone (Samsung Galaxy S) and putting a custom rom on it. I managed to put on Darky's latest rom last night. However it was giving me problems with the Android market (it crashed when it came to the installation part). Therefore, I want to get rid of all the modifications I made to my phone and go back to the settings how the phone was shipped to me.
How can I do that?
I already downloaded the original firmware (2.2.1) using this forum. It is a .tar file and I tried to flash it with Odin. Seemed to work at the beginning but there were still some elements, like apps, of the old Rom left. So I did the process again.
Now my phone starts up but after the boot screen I only have a black screen with the typical crash vibration patterns all the time. After flashing it again I get into the recovery mode showing errors.
Can somebody please tell me how to go back to my original firmware, without a custom rom, root access etc.?
I'm afraid that I will brick my phone now.
thank you
(I searched this forum but couldnt find anything related to my question)

Try a different firmware. Had the same issue when flashing a 2.1fw on an already 2.2 custom rom. Try a US 2.2 jpy. You can get any galaxy s firmware from (www samfirmware com).
Sent from my GT-I9000 using XDA App

thank you for the quick reply.
I am not 100% exactly sure if my procedure is right. Here is what I do:
1. Put your phone to download mode (hold down: volume down, home key, power)
2. Do not plug in your phone yet.
3. Start Odin3
4. Tick "Re-Partition", and also check that "Auto Reboot" and "F. Reset Time" have been ticked.
5. Click "PIT" button and select s1_odin_20100512.pit file.
6. Now, plug in the phone and wait until Odin finds it.
7. Click "Start" button... <Firmware update start...> <Get PIT for mapping...> appear. The phone will turn off and the screen indicates "Reset". Wait until Odin indicates "Pass".
8. Plug out your phone, remove the battery, put it back in and put phone to download mode again.
9. Click "Reset" button in Odin and untick "Re-Partition" box.
10. Do not select PIT file again. Just leave it empty.
11. I select here the downloaded firmware (2.2.1) in PDA. Everything else is blank (PHONE and CSC)
12. Phone installs and Odin shows pass
Now, the phone does not boot but goes into system recovery 3e showing an error message E: Cant mount /dev/block/st110
E: copy_dbdata_media:Cant mount DBDATA
After I select "reboot system now" the phone boots but gets stuck right after the Samsung logo disappears. then I only see a black screen and the vibration.
What am I doing wrong here?
thank you I really appreciate it!!

Follow instructions Block 2 method Odin and use the firmware you want .
http://forum.xda-developers.com/showthread.php?t=818556
jje

i can't go into recovery or download mode after flashing

Hi,
could anyone help!
my device is galaxy ace s5830i
i have already rooted my device and used CW Recovery and taken a copy of my original system .oki
i wanted to set up a custom rom i restarted and reset and deleted the cash then installed the rom.
i think it was Retribution beta
then i wanted to update to that custom rom (MindCR ICS)
all i did i restarted my phone of course went into R mode and reset and deleted the cash then installed that next custom rom .
after installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.

dana25 said:
After installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
Click to expand...
Click to collapse
I think you have a hard brick.....
Maybe JIG / JTAG can help.
Sent from my GT-S5830i using xda premium

RubenStauttener said:
I think you have a hard brick.....
Maybe JIG / JTAG can help.
Sent from my GT-S5830i using xda premium
Click to expand...
Click to collapse
would you provide me with that or tell me how?

dana25 said:
Hi,
could anyone help!
my device is galaxy ace s5830i
i have already rooted my device and used CW Recovery and taken a copy of my original system .oki
i wanted to set up a custom rom i restarted and reset and deleted the cash then installed the rom.
i think it was Retribution beta
then i wanted to update to that custom rom (MindCR ICS)
all i did i restarted my phone of course went into R mode and reset and deleted the cash then installed that next custom rom .
after installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
Click to expand...
Click to collapse
I have this problem before and i managed to use ODIN3 v1.83 (can use Odin3 v3.07) to detect my phone and flash a stock rom onto the device. I followed the advice given on this excellent thread by Supermini.
http://forum.xda-developers.com/showthread.php?t=1071970
As mentioned on his thread make sure you have the latest stock firmware from the sammobile site or by using Check Fus Downloader as per the guide in Rafael thread http://forum.xda-developers.com/showthread.php?t=1551156, a working samsung USB driver to detect your mobile on your PC and a copy of ODIN3 v1.83 (or v1.84, v1.87, v3.07 run ODIN in administrator mode if using in windows). Ultimately if this this fails you could always try a USB jig which can be purchased from ebay, etc. to get the phone into download mode.
Good luck and if this helps make sure you send a thank you to Supermini.

Viprdxd said:
I have this problem before and i managed to use ODIN3 v1.83 (can use Odin3 v3.07) to detect my phone and flash a stock rom onto the device. I followed the advice given on this excellent thread by Supermini.
http://forum.xda-developers.com/showthread.php?t=1071970
As mentioned on his thread make sure you have the latest stock firmware from the sammobile site or by using Check Fus Downloader as per the guide in Rafael thread http://forum.xda-developers.com/showthread.php?t=1551156, a working samsung USB driver to detect your mobile on your PC and a copy of ODIN3 v1.83 (or v1.84, v1.87, v3.07 run ODIN in administrator mode if using in windows). Ultimately if this this fails you could always try a USB jig which can be purchased from ebay, etc. to get the phone into download mode.
Good luck and if this helps make sure you send a thank you to Supermini.
Click to expand...
Click to collapse
thanks and sorry for late but as i told you i cant go into rev or download mode i tried to use odin 1.8 and the latest version but it doesn't recognize my phone shall i lose hope!

bro i think u most probably bricked ur phone but dont worry try opening download mode. then using the odin u install ur stock rom. Then u can access ur r mode. but try to read the entire procedure..of flashing the rom.

dana25 said:
thanks and sorry for late but as i told you i cant go into rev or download mode i tried to use odin 1.8 and the latest version but it doesn't recognize my phone shall i lose hope!
Click to expand...
Click to collapse
So . . . last thing to rescue your phone is buy on e-bay or in other place JIG if it isn't help you then try in phone service and say you tried install new ROM with Kies and your phone is brick (maybe it'll work).

Say to Service Centre Representatives that you kept your at charging last night
And when you woke up
It was not booting up
Pretend as if you dunno anything about root or ROM
They fixed my bricked phone
I am not sure if I am breaking any forum rule by telling this

Hey bro sorry for the late reply also, please before you do anything else try following my instructions.
1) download Odin v3.07
2) source the stock firmware you want to flash from sammobile.
3) make sure you have the Samsung mobile driver.
4) open and run Odin as administrator and load the single file in the PDA and highlight the tick box.
5) shut the phone down and take out your Sim card.
6) put the mobile into download mode as normal (press both up/down vol keys +power)
7) connect the phone to the PC and check in Odin to make sure its com port is detected.
8) then flash through Odin as normal.
I understand what your saying about no download screen appearing, I have found through experience that custom kernels can cause no download screen to appear. Normally with stock kernel this is not a problem but with custom kernels sometimes all you get is a black screen. Ignore this and just make sure that Odin is detecting the phone and try to flash, chances are it will flash the stock ROM and kernel. If you get the setup connection error in Odin and the fail 0\1 just try another USB port on your PC and keep persevering.
Please keep us updated so we can help you if you need it.
Sent from my Nexus 7 using xda app-developers app

Why will it be hardbricked if the custom roms are based on s5830i stock roms?

But it is probable that we did I not flash the rom properly as per procedure..so is there a chance that it be bricked? Else the rom may have some problem... just telling the probability
Sent from my GT-S5830i using xda premium

Help me .
help me on fixing my ace s5830i , my problem is after flashing it with RazoDroiD my phone seems to be ok , i decided to change my firmware by a stockrom using Odin mode or the Volume Up+Down+On off it stays on blank screen . Can you help me on fixing this ? and what do you call this problem .

Try following my instructions.
1) download Odin v3.07
2) source the stock firmware you want to flash from sammobile.
3) make sure you have the Samsung mobile driver.
4) open and run Odin as administrator and load the single file in the PDA and highlight the tick box.
5) shut the phone down and take out your Sim card.
6) put the mobile into download mode as normal (press both up/down vol keys +power)
7) connect the phone to the PC and check in Odin to make sure its com port is detected.
8) then flash through Odin as normal.
I understand what your saying about no download screen appearing, I have found through experience that custom kernels can cause no download screen to appear. Normally with stock kernel this is not a problem but with custom kernels sometimes all you get is a black screen. Ignore this and just make sure that Odin is detecting the phone and try to flash, chances are it will flash the stock ROM and kernel. If you get the setup connection error in Odin and the fail 0\1 just try another USB port on your PC and keep persevering.
Follow this and don't worry about black screen just make sure Odin detects your PC com port.
Sent from my Nexus 7 using xda app-developers app

[Q] After rooting phone is not starting, please help...

Hi,
I have Samsung Galaxy S I9000 running Ginger Bread.
I wanted to upgrade my phone to Ice Cream Sandwitch or Jelly Beans. In order to do it, I started with below steps to root my mobile.
1. Installed latest Clockwise Mode application into my phone.
2. Installed Odin3 v1.7 in my laptop.
3. Downloaded CF-Root-XX_XEU_JPY-v1.3-BusyBox-1.17.1.tar on my laptop.
4. Started Odin first.
5. Disconnected mobile and started in download mode with Volume Down + Home Button + Power Key.
5. After starting the download mode, connected mobile to laptop using the USB.
6. Keep all the default values in Odin3 i.e. Re-Partition option unchecked, Auto Reboot and F-Reset Time option enabled. Selected tar file CF-Root-XX_XEU_JPY-v1.3-BusyBox-1.17.1.tar in PDA option.
7. Connected mobile and it detected ID Comm [Highlighted in Yellow].
8. Finally click on Start button.
After starting the process was completed and Yellow color changed to Green one, phone was auto reboot.
But after reboot it is just stuck on start of screen and not going ahead. I wait for 2 hours but still not working.
Could you please help me how I can solve this issue now?

Did you try to pull battery out and restart the phone again?
Do you still can go in CWM with 3 button combo again?
If yes then try to flash a ICS or JB kernel (depending on what ROM you finally want to have on your phone) via CWM and then go in advanced and restart recovery (if available), otherwise just try to flash the rom.zip on top.
If CWM is not possible, the go in download mode an falsh a tar version of kernel via ODIN.
Here are different semaphore kernels for each android version:
http://78.46.194.137/downloads/gt-i9000-ics
http://www.semaphore.gr/downloads/gt-i9000-jb
For ics it should work after 1. flash, but for JB you have to flash it 2 or even 3 times, if after restart phone does not boot. Then battery out again, start in recovery and flash zip again.
Good luck and good success .

I think, at this position, installing a new gingerbread stock ROM will be preferable. Try installing XXJVU. Then root with cwm and install any slim bean version in case you are interested to use jelly bean.
Sent from my GT-I9000 using xda app-developers app

Sure that will be the best way....but my suggestions do not take much time, so why not give them a try .
But if its not going, then a restock is the best you are right:
What I always do for restock is using slappys rescue kit.
Unzip it and flash the Rom via Odin. There is everything, also a txt file with a guide included.
http://forum.xda-developers.com/showpost.php?p=29114573&postcount=2
If you want to have slim rom then its recommended to flash CM9 first or flash a modem afterwards via cvm, because slim does not have a modem included.
And/Or just follow the installation guides/recommendations from the single ROM Threads.

Thanks Guys for your help.
My issue is resolved with below post.
http://forum.xda-developers.com/showthread.php?t=1809098

phone not starting
guys i cant start my phone....even the three buttons ar not working...it is just loading and loading....help please
model-gt-s5830i

viral1999 said:
guys i cant start my phone....even the three buttons ar not working...it is just loading and loading....help please
model-gt-s5830i
Click to expand...
Click to collapse
You are here in totally wrong section: this is a i9000 help thread section. Hopefully you didn't flash a i9000 rom, otherwise your phone is hard bricked.
tetakpatalked from Nexus 7 flo

Me 2: It was from low battery in my case
I had similar problem when rooting my Samsung Galaxy S5 smartphone with Odin3. After rooting with a success message my phone was showing just the Samsung Logo each time I was trying to turn it on without loading OS. I googled and directed here and connected my phone to the charger as its mentioned in a link you provided which solved your problem. It turned on automatically after a few minutes while of charging and when turned on it was charged approximately 40%.
As I was very afraid my phone got serious harm at first I hope this maybe a sedative probability for duds really worry about what happened to their smartphone.

I rooted my phone le tv without pc bt after rooting it is not starting pls help me how to start my mobile again

Imbhavya said:
I rooted my phone le tv without pc bt after rooting it is not starting pls help me how to start my mobile again
Click to expand...
Click to collapse
What exactly did you do, which phone model and what does it display now?
Sent from my A0001 using Tapatalk

[Q] Help Me Please!!??!! (clockworkmod recovery)

I have a Samsung Galaxy Mini and I succesfully rooted it, however it seems to be impossible to add cyanogen to it cause ii need clockworkmod recovery
1. I tried downloading it from the stock loader (on the update from sdcard place thing ) and it will just freeze when it comes to Replacing stock recovery with ClockWorkModRecovery. I have tried severall versions of it, including the one that came from the clockworkmod website but all of them just freeze
2. I tried connecting them to the pc but samsung kies can't see my phone and i can't even find all the files needed to use them on Odin
so what do I do????

MrRootGuy said:
I have a Samsung Galaxy Mini and I succesfully rooted it, however it seems to be impossible to add cyanogen to it cause ii need clockworkmod recovery
1. I tried downloading it from the stock loader (on the update from sdcard place thing ) and it will just freeze when it comes to Replacing stock recovery with ClockWorkModRecovery. I have tried severall versions of it, including the one that came from the clockworkmod website but all of them just freeze
2. I tried connecting them to the pc but samsung kies can't see my phone and i can't even find all the files needed to use them on Odin
so what do I do????
Click to expand...
Click to collapse
First of all make sure you installed drivers in Samsung Kies. After, make sure to have working version of odin. Tried connecting the booting into download and see if it detects it?

MrRootGuy said:
I have a Samsung Galaxy Mini and I succesfully rooted it, however it seems to be impossible to add cyanogen to it cause ii need clockworkmod recovery
1. I tried downloading it from the stock loader (on the update from sdcard place thing ) and it will just freeze when it comes to Replacing stock recovery with ClockWorkModRecovery. I have tried severall versions of it, including the one that came from the clockworkmod website but all of them just freeze
2. I tried connecting them to the pc but samsung kies can't see my phone and i can't even find all the files needed to use them on Odin
so what do I do????
Click to expand...
Click to collapse
Make sure your mini has gingerbread and samsung drivers installed on your pc/laptop.
Before you begin please make sure your battery has at least 70% of charge.
1. Download Odin Multidownloader v4.38 for GTS5570, Tass_v1.ops and Clockwork Mod Recovery v4.0.0.5(tass-recovery-cwm.tar) if you do not have them already. (Attachments)
2. Run Odin Multi downloader v4.38 and select the Tass_v1.ops by clicking OPS button.
3. Select One Package Option and Click One Package button and select the tass-recovery-cwm.tar file you downloaded.
Leave other settings to default (i.e. don’t change any other options/settings)
4. When you are done reboot your phone in download mode (Press Volume Down + Home + Power button to go to download mode)
5. Connect your phone in download mode to your computer via USB Cable.
6. When Odin detects your phone (If you see a com port number written in yellow background at the top left, then your phone is detected. View image.), click Start button.
7. Wait till Odin finishes the job (approx. 3-5 minutes) and when it reports ‘PASS’, you can disconnect your phone.
Go to the recovery mode (Press Home + Power button) and see your new recovery with tons of useful options. Now that you have CWM recovery you will be able to do just more than nandroid backups. You can also partition your sdcard as well as flash a custom rom on your galaxy pop. Go ahead and experiment with various options. But, be careful playing with your device’s recovery is very risky task if you lack appropriate information or skill.

Please help me i want to install cwm on my rooted gts5570 froyo using mobile odin lite..
send from my GT s5570 froyo..

Please any body answer...how to install cwm or upgrade my froyo gts5570 without computer...i have odin mobile lite also installed
send from my GT s5570 froyo..