I've cracked the outer layer of glass on my optimus x2 which I assume is just the digitizer (I'm new to all this smartphone jazz but i've had alot of experience with building computers and such and i can follow instructions) and i'm guessing the cheapest way to repair this thing is to do it myself. I emailed LG asking about what they can do with it and they were asking for £20 just to look at the damn thing so i can't imagine actually doing any work on it would be cheap.
(can't post links but it was just some cheap generic one from amazon for £30)
I'm guessing something like this would do the job but I also need some special adhesive to get the LCD to stick to the digitizer am i right? I'm worried that it will not be as responsive or i'll do it wrong and i only recently dished out £250 for this so i'd like to try and do this right. I've watched a couple of videos on youtube which have helped a bit but none went right through the process so if anyone with any experience doing this could tell me about it i'd be very grateful.
its not that hard. everything just peels off when heated with a hair drier.
the digitzer should come with sticky strips which go around the outside of the lcd and stick to the out side of the digitizer.
Also try to get a digitizer with a frame already on it. otherwise youll have a little bit of a hard time trying to remove the glass from the frame, then gluing in the new one with adhesive.
http://www.youtube.com/watch?v=K77Xepb6yd8
Just follow this guide exactly, you should be fine man
Supupa said:
its not that hard. everything just peels off when heated with a hair drier.
the digitzer should come with sticky strips which go around the outside of the lcd and stick to the out side of the digitizer.
Also try to get a digitizer with a frame already on it. otherwise youll have a little bit of a hard time trying to remove the glass from the frame, then gluing in the new one with adhesive.
Just follow this guide exactly, you should be fine man
Click to expand...
Click to collapse
Thanks for the reply, that's a lot of help Could you recommend any retailer that sells these? I can't work out if any of the ones i'm looking at come with the sticky strips. Would I also not need any adhesive if it comes with the frame? I'm not sure I trust myself too much with doing that either.....
I recently replaced my digitizer. I ordered a digitizer already in housing off ebay, shipped from Hong Kong. I would strongly recommend buying it with housing, as it's often difficult to completely make sure that dust does not get between the digitizer and the screen when you're using adhesive tape.
When disassemblying the o2x, I found the adhesive sticking the LCD to the digitizer frame was too strong for the LCD to come off just like that (be careful, it's quite fragile). I heated the LCD a bit using a hair dryer, to make it come of easier. This has the added effect that enough adhesive may stick to the LCD, so you don't need to replace it when placing it in the new frame.
I only added a couple of adhesive strips to the top and bottom of the new frame before mouting the LCD. That was pretty stupid, cause the extra 0.1mm between the digitizer and the LCD means that when tilting the phone ~60 degrees to the sides, I can see the backlights at the sides of the screen. Surprisingly this doesn't seem to add any noticeable backlight bleeding though, so it's not a problem at all. However, I'd suggest to try and see if the LCD sticks to the frame with the old adhesive, before using adhesive strips. And if using adhesive strips, make sure you remove all the old adhesive from the LCD, and use adhesive strips all around the frame.
The only minor things to look out for are:
- Be very careful with the LCD! It takes very little flexing before getting dead stripes/areas.
- Careful with the plastic at the USB port - it's a bit difficult to get to fit, and it's quite thin, so I figure it will break easily.
- At the top of the phone, where the digitizer (or LCD, I don't remember) cable is mounted, there's a little grey rubber-thingy - it suddenly fell off my phone, and it took embarrassingly long to figure out where and how it fits
- The small backup battery (?) in the upper left corner of the phone is glued to the frame. I used a small flat-headed screw driver to release it from the frame. Don't try and remove it by yanking the flex cable.
But all in all, replacing the digitizer with a new one (already in a frame) was a quick and easy operation.
Edit: I bought this digitizer: ebay. co. uk/itm/T-Mobile-LG-P990-Optimus-2X-Replacement-Touch-Screen-Digitizer-Frame-ZVLT338-/160656180054?pt=UK_Replacement_Parts_Tools&hash=item2567dac356 and some cheap 2mm adhesive strips like ebay. co .uk/itm/3M-Sticker-tape-Adhesive-cellphone-touch-screen-LCD-2mm-HTC-Samsung-Sony-/200710386131?pt=UK_Mobiles_Accessories_RL&hash=item2ebb4571d3#ht_1099wt_1165
Why didn't I think of this before.. been cracks in my display for almost a half year now.
Local repair company said it takes two weeks to fix.. I had no plans to go two weeks without my phone
Just ordered one
p990 mother board
dear friend
sorry for my eanglish i write from italy.
i need your help but before i have to explane my problems:
i've a lg optimus x2 (p990) with water demage.....
i cleaned the mother board with success..now the phone turn on and fix the phone net and it can recognize the battery charge.
but unfortunately WI-FI,BLUETOOTH AND MIC(the people who call me can't hear me) DON'T WORK, THE GPS I DON'T KNOW BECAUSE I HOPE TO RESTORE THE WII-FI AND INSTAL GOOGLE MAPS.
i'm sure that wi-fi problems come from the mother board because i have an other same device so i made a test using the good one but the mic problems persisted
my question is ,do you know wich parts i have to check and clean again?
do you know where the wii-fi component are located in the mother board?
thanks for your attention
a friend
marco zavatta
Sorry for bringing up this old thread, but I have to ask, are all Optimus 2X digitizers the same? Don't some have different connectors or anything? Can I order any Optimus 2X digitizer for my P990? I was thinking of this digitizer, will it work?: http://www.amazon.co.uk/Digitizer-F...7BUA/ref=sr_1_1?ie=UTF8&qid=1364833172&sr=8-1
I had to replace mine recently, I read there are cheap ones where they only recognize 2 fingers instead of 5 like the genuine LG part. I ordered my digitizer from Ebay for around 18 british pound, I followed a few videos on Youtube with the disassembly, it's actually not that hard.
Keep in mind though that not all digitizers might come with glue attached or come with plastic tools, so keep a small bottle of glue and some plastic tools (credit card style plastic, knife) ready. One video recommends buying foam pads to glue around the digitizer, I didn't find that necessary, I just glued my new digitizer back onto the frame without problems. I accidentally made some glue residue onto the inside of mine, so make sure that you work very carefully
I have done this twice. It is not too hard and a lot cheaper. I follow this guide: http://www.youtube.com/watch?v=Po8hBaZt__o.
Do yourself a favour and buy a digitizer with bezel (which is a frame). The first I bought was ****ty Hong Kong digitizer, the second one good Polish(?): http://www.ebay.co.uk/sch/m.html?_nkw=p990&_sacat=0&_odkw=&_osacat=0&_armrs=1&_ssn=digitaloutlet.pl
The hardest part is not to get dust between digitizer and lcd screen - you could consider wearing gloves...
The second hardest part is not to bend bezel around usb inlet.
Good luck!
So there's no connector difference?
kaspar737 said:
So there's no connector difference?
Click to expand...
Click to collapse
The connector should fit any p990. If you are in doubt email the seller.
oneearleft said:
The connector should fit any p990. If you are in doubt email the seller.
Click to expand...
Click to collapse
Sorry for coming back to this rather old thread, but I have recently replaced the digitizer on my LG P990, bought on ebay shipped from Hongkong, following the video guide cited above. However the digitizer now works erratically with upper 1/4 not responding to touch, and sometimes the whole thing does not work, so I am unable to unlock the phone at all. The only thing that worried me during replacement was the thin layer of plastic film on the inner side, which teared off when removing protective layer (the film was extremely thin and fragile)-would this be the problem? Or the digitizer itself is of low quality?
Any suggestions appreciated.
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
gunemalli said:
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
Click to expand...
Click to collapse
i am looking for the LCD and digitizer assembly. but i am trying to find OEM part
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
housing is not an issue
Lttlwing16 said:
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
Click to expand...
Click to collapse
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
i bought one
squee666 said:
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
Click to expand...
Click to collapse
i did buy one from ebay today, after been an annoying person with lots of questions hahaha. i refused to buy from anyone below 99% profile credential on ebay. here are the questions i asked lol
Is the LCD screen manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store? if not, is the same Quality, TRUE IPS LCD with Gorilla Glass 2 digitizer?
Is this LCD part brand new or refurbished from reclaimed old parts?
Digitizer – Is the Touch Panel manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store?
Digitizer – Is the Touch Panel new or refurbished, or reclaimed from old parts?
and if I bought a brand new in box sealed G2 from LG, the part I’m asking about would be 100% identical with no differences in quality or condition?
does it work on D800 model, if not do you have one that works with D800 that is a genuine OEM?
is it OEM (Original equipment manufacturer), does it have part number on the flex cable, and LG display co,ltd label ?
only one seller, answered all of them concisely, without political correctness or avoidance. lots of them stopped talking to me, and some only answered vaguely. i had one hilarious response, who said the the screen is OEM but not genuine, i insisted for him to elaborate, he said OEM but not original. all of us know that OEM stands for Original equipment manufacturer. i sent him a response, that it does not make sense to be OEM but not original. he replied back OEM for them is, Optical equipment manufacturer lol, heck i do not even know what does that mean lol. i took a screenshot of the definition and sent it to him, he never replied back hahaha. many shady seller on ebay
P.s once i receive the part and install it, i will update on the condition/quality
can post the link for the seller you bought the assembly?
thank you!
Link
noris08 said:
can post the link for the seller you bought the assembly?
thank you!
Click to expand...
Click to collapse
http://www.ebay.com/itm/251591046010?_trksid=p2060778.m2749.l2649&ssPageName=STRK:MEBIDX:IT
working
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
sdcaliber said:
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
Click to expand...
Click to collapse
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
jamracer said:
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
Click to expand...
Click to collapse
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
sdcaliber said:
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
Click to expand...
Click to collapse
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
jamracer said:
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
Click to expand...
Click to collapse
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
sshark said:
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
Click to expand...
Click to collapse
yeah maybe, all depends of course. most of these products are subject to opinions if there is doubt about their OEM legitimacy. but for me, i will not buy non OEM for battery again, it scares the hell out of me. let's say i had a horrible experience before. i had Note 3, and bought a battery for it. the extra capacity made me drools lol, so i went with it. days later, i found the phone in total meltdown, literally. woke up from my sleep, and the phone is melting/fire.... scary scary experience. the good thing, i do not sleep while my phone next to me. it was on my table, charging.
side not: the original battery of Note 3 malfunctioned
OEM
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
I bought it on Ebay and now it´s working fine, nice!!.. First I bought only the digitizer and it was faulting, but now this assembly is really working fine:
http://www.ebay.com/itm/281280382756?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Regards,
Just posting to share my experience. I bought a replacement lcd\digitizer for my G2. Once installed, i had white lines going up and down the screen.
Some devices use different panel hardware (JDI instead of LGIT) and you will have white lines after using patched kernel. You must use those kernel with "_jdi" in its name. More info:http://forum.xda-developers.com/show...&postcount=122
After flashing the new kernal the phone works great. The phone does get noticeably hotter, unfortunately, which is a little worrisome.
The kernal issue and the heat lead me to believe that what i bought was not oem.
Sent from my LG-D801 using XDA Premium 4 mobile app
Is D800 frame compatible with LS980?
sdcaliber said:
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
Click to expand...
Click to collapse
I was just working on a frame lcd assembly swap on an LS980 rev 1. The frame I bought was a Verizon LV980 and the vibrator was off buy at least 3mm, I didn't mind losing the vibrator to gain a good lcd. Then the proximity detector layout was different, the LS980 had an extra piece that fit in a hole, but it could be removed. About 5mm below that is a ground connector for the motherboard on the LS980 but not on the VS980 and the tab holding the antenna coax hit the motherboard making the frame about 0.5mm too small causing the mobo not to seat.
All of these could be amended. Shave 0.5mm of the soft metal chassis, very easy, mobo grounds in at least six other places and proximity sensor had a removable tab.
But the bottom of the chassis where the dock port/usb board sits was just too different, the LS980 daughterboard wouldn't seat, it was larger. It could be forced but only at an angle that made the usb port off-center and not parallel to the opening. My repair stopped and re-assembled the phone with the LS980 chassis complete with my damaged lcd.
-----attached pics of proximity sensor, and ground connector area, didn't take more, I was getting mad.
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
Actually I bought an LCD from this company. I am very happy with it. It is true HD and the it was shipped for me in 3 days as they said. At first I was very worried with the comments but I took the risk and I am satisfied with it. I don't know why others complain about it but I recommend them.
hi...
i have a d802 device with broken screen glass...
touch & gestures work... screen works... it only has a few cracks on it...
can i just replace the front glass (cheaper solution?) or must i replace the whole digitizer and front panel...
any suggestions on trusted online shops thazt sell genuine LG d802 parts?
thanks in advance
Digitizer and glass is a single unit, and is readily available on ebay (for cheap) so there is that. The thing is that it is next to impossible to separate the glass from the display itself, and without professional tools the result of the reassembly will be quite awful. The best would be to exchange the display assembly as a whole. This is actually done quite easily. Lots of guides are available online, which just makes the process even easier.
Also for where to get the displays. You can actually contact LG or one of their service providers to purchase the display assembly. This way you are completely sure to get a top quality product. This is a tad more expensive though.
Ebay is also another place to get displays, the quality varies greatly here (have gotten anything ranging from completely original to barely functioning knock off. )
Etradesupply is apparently the best place to get displays at the moment, as their S+ grade is comparable to the ones you get from LG
http://www.etradesupply.com/lg-g2-d802-lcd-screen-and-digitizer-assembly-black.html
lusseMagnet said:
Digitizer and glass is a single unit, and is readily available on ebay (for cheap) so there is that. The thing is that it is next to impossible to separate the glass from the display itself, and without professional tools the result of the reassembly will be quite awful. The best would be to exchange the display assembly as a whole. This is actually done quite easily. Lots of guides are available online, which just makes the process even easier.
Click to expand...
Click to collapse
yes, i saw some youtube tutorials and removing glass from digitizer is a pain in the a$$, it can be done using hot air to melt the glue - but it's a time consuming process...
what interests me more is a whole screen section (glass+digitizer) and buying a proper genuine one for d802 (i think some people had issues with installing wrong panels from other variants to their d802 model)
thanks for your helpful answer :good:
60nine said:
yes, i saw some youtube tutorials and removing glass from digitizer is a pain in the a$$, it can be done using hot air to melt the glue - but it's a time consuming process...
what interests me more is a whole screen section (glass+digitizer) and buying a proper genuine one for d802 (i think some people had issues with installing wrong panels from other variants to their d802 model)
thanks for your helpful answer :good:
Click to expand...
Click to collapse
The thing is that the D800 and Veriozon models (as I recall) uses different digitizers. The connectors for these should not physically be able to connect to the D802 motherboard.
But to be able to cure the optically clear glue used for displays you will not only need an uv light but also lots of practice. Air bubbles get caught under the glass way too easily for it to be viable.
One more thing to note. the LCD itself is too easy to bend. Any flex will destroy it. Should also note that I too have watched the video where someone separates the G2 glass from the LCD and have tried to follow along multiple times. Every time resulting the same way. LCD breakage. Both times the polarizing filter got unstuck. So if you really want to go this route, my advice would be to find a professional to do the job.
Recently I had same problem: cracked digitizer. After my experience - first trying to replace only digitizer - NOT GOOD. I had to buy a whole set - digitizer and LCD. Just pay attention to your type of LG G2 - you can find all the types. But I am not sure if you can find a genuine replacement. Usually they are substitute, with no logo. But everything works fine. Pay attention also to where and how the connectors are placed and the most important thing - after you took out the old LCD give it a good heat to the back of the battery pack because is stuck with strong biadhesives and try not to pry too much the battery.
I just replaced mine G2 D802 (from 2013) Lcd, you need to replace the whole thing (screen+lcd)I think, you can buy the Lcd from the Internet. I bought the lcd about $50 and got the shop to replace it for $6. Now my G2 is like new.