Database Develop

Runnning the unlocker step-by-step

This excruciating step-by-step might help someone...
Wherever I mention establishing a WMDC/AS connection, make damn well sure that the connection is established... If you don't, you won't kill your device, but you won't unlock either.
-Establish a WMDC(Vista) or Activeysnc connection(XP)
-Confirm this!
-Start the unlocker program on your PC.
-Click "Flash SPL" (Step 1)
-Click "Yes"
-On the Treo you are prompted to allow the install of itsutils.dll and jumpspl.exe. Say YES to both.
*****The Treo will reboot. Don't click anything on the PC until the treo is back up and a WMDC/AS connection is re-established
-On your PC, you will see "Cheetah RUU". Click Next.
-Click Next again
-Click Next
-Click Update
-Click Next
-Click Next
******The Treo will reboot into bootloader mode and flashing begins. The device will reboot after the flash completes. Don't click anything on the PC until the Treo is back up and a WMDC/AS connection is re-established
-Click finish
-Click "Unlock Radio" (Step 2)
-Click Next
-Click Next
-Click next
-Click Update
-Click Next
-Click Next
******The Treo will reboot into bootloader mode and flashing begins. The device will reboot after the flash completes. Don't click anything on the PC until the Treo is back up and a WMDC/AS connection is re-established
-Click Finish
-On the PC is a notice "Read this through!". Confirm that you have a good WMDC/AS connection.
-Click OK
-On the Treo click "Yes" to allow athena unlock.exe
-On the Treo follow the instructions - check off SIM and CID unlock
-On the Treo click "Unlock" and wait for it to finish, then click OK on the athena unlocker on the Treo, and then click OK on the Treo to close the athena unlocker.
-On the PC, click OK
-Ensure you still have a WMDC/AS connection.
-On the PC, click "Flash normal radio" (Step 3)
proceed through the series of "Next", the device will go into bootloader mode and flash one more time. The device will reboot when done, and you should be all set.

Hey Summiter. Thanks for your tutorial. Got one question. I've done the whole process and now my SPL-says 1.40.01 OliNex. So I'am assumming that all went well. The only thing that gets me is that in you guide you state that this process will hard reset my device and all info. will be lost. My information as well as my programs all remained intacked. Is this OK. or am I missing something.
Thanks.

My bad..it won't do a hard reset. My device hard reset when I was running a different process, not the released unlocker. =) Sorry to cause concern.
As for the slow 3G speeds, Olipro is looking into it.
manfly9884 said:
Hey Summiter. Thanks for your tutorial. Got one question. I've done the whole process and now my SPL-says 1.40.01 OliNex. So I'am assumming that all went well. The only thing that gets me is that in you guide you state that this process will hard reset my device and all info. will be lost. My information as well as my programs all remained intacked. Is this OK. or am I missing something.
Thanks.
Click to expand...
Click to collapse

summiter said:
My bad..it won't do a hard reset. My device hard reset when I was running a different process, not the released unlocker. =) Sorry to cause concern.
As for the slow 3G speeds, Olipro is looking into it.
Click to expand...
Click to collapse
Thanks for your quick response.

Can anyone check Radio Ver after last step
Can someone verify the Radio Ver after 3rd step (Normal Radio Flashed Back to Device) , Olipro said to my post that by having Radio at 1.16 , i didnt complete last (3) step , but i defenatly did , and my Radio still 1.16 , where i had 1.52 before unlocking ???????????????????
Hitec

I called cingular tonight because i have been trying to get my 750 paired with my tom tom one 3rd edition for use of the weather updates and cameras and such. Through conversation with a support representative, and trying to troubleshoot why it couldn't use the wireless connection of the phone, the representative asked me to check a few things on my phone. While answering some questions, one of which was about device software and such and i told him i had windows mobile 6 installed.
From this point on he led into reasons why i should be using it with out it being released and such which is to be expected. He also stated that doing to much to the phone can possibly make the phone upgradable when the real WM6 update is released. This he mentioned were changing the boot loader, IPL and SPL software in the phone, that and using bogus releases of software. The reason being he said was that the soon to be released update probes the phone deeply because everything has been updated including the boot loader stuff.
Now i cant confirm or deny any truth to these statements but the only thing i had done with mine was a try a few new firmwares but after my conversation with them i quickly reverted back to WM5.

jhowle said:
From this point on he led into reasons why i should be using it with out it being released and such which is to be expected. He also stated that doing to much to the phone can possibly make the phone upgradable when the real WM6 update is released. This he mentioned were changing the boot loader, IPL and SPL software in the phone, that and using bogus releases of software. The reason being he said was that the soon to be released update probes the phone deeply because everything has been updated including the boot loader stuff.
Click to expand...
Click to collapse
F.U.D.
That's utter ****ing bull****, the RUU will do no such ****ing thing, and even if it does, there'll still be a base NBH to dump and flash... complete crap.
the bootloader might well have been updated, but the Hard-SPL one on there isnt going to let it overwrite it, mate.

jst passing on the info dude,, don't blame me.. they said it

mines unlocked anyway, but i did a remote unlock with GSM libeerty.com only cocts 39 bux and it does work. i figured if i spent 39 bux and avoided the potential of bricking my treo than it is worth it.

jhowle said:
mines unlocked anyway, but i did a remote unlock with GSM libeerty.com only cocts 39 bux and it does work. i figured if i spent 39 bux and avoided the potential of bricking my treo than it is worth it.
Click to expand...
Click to collapse
well not really, but you paid your money and took your choice

i guess i just see how the HARD SPL really does any different besides bypass the lock function. I have tried some very similar programz with my black berries and even after they said they were unlocked you could still goto the SIM CARD Screen under advanced options and hold ALT and press M - E - P - 2 and walla the code entry screen window would still come up.

after completing step 2, I don't even have the option to install athena unlock.exe ?
Also, it gives me an error after I click "Read this through"
What's going on?
Am I doing something wrong?
EDIT:
itsutils.dll didn't even install
During step 1, jumpspl and enterbootloader are installed, NOT ITSUTILS
Any help is appreciated

Why no flash?
I just tried running the unlocker. I have an AT&T branded and locked Treo 750 with Windows Mobile 6. When I run the unlocker, it installed itsutils.dll the first time, but the freeze that i am supposed to look for never occured. Then it installs the jumpspl.exe, and restarts. Then i wait until the ActiveSync is reconnected, and run the RUU. The RUU says that it fails flashing either radio (the patched one or the stock one) after 7%, and gives me an error. But then the unlocker application ran on the phone, and said it was successfully unlocked. I check the SPL version and there is nothing about 1.40 OliNex. Is there a step that I am obviously missing? I thought i had to CID unlock it first, but it gives me the option to CID unlock and it says it is unnecessary on the unlocker itself. Im sorry for being such a bonehead, but any suggestions? Thanks.

just goto www.gsmliberty.com it onlu cocts 39.99 for a remote unlock and there is no risk of bricking ur phone

unhandled exception error
Treo 750 with AT&T running WM5 trying to unlock to use on another GSM carrier. Downloaded the current treo 750 unlock software from this site. after step 2 I get unhandled exception error and cannot continue. Phone is synced properly and I have followed all steps to the "t".
I see this question asked many times throughout the site but never an answer. can someone let me know what causes it and how to fix it. I know lots of people would appreciate it.
Thanks in advance for your time.

JBoever said:
Treo 750 with AT&T running WM5 trying to unlock to use on another GSM carrier. Downloaded the current treo 750 unlock software from this site. after step 2 I get unhandled exception error and cannot continue. Phone is synced properly and I have followed all steps to the "t".
I see this question asked many times throughout the site but never an answer. can someone let me know what causes it and how to fix it. I know lots of people would appreciate it.
Thanks in advance for your time.
Click to expand...
Click to collapse
I think I manually copied the Athenaunlock.exe to the phone and ran it at that step. Note - this was after the special "unlock" radio had already been flashed. Finally, I did a hard reset and then installed a new OS - ROW 2.23 which previously would not load on phone (because it was locked).
I hope this helps.

unlock not working. unhandled exception
I get the following error after I finish the radio patch and it trys to run athen unlock.exe
Unhandled exception has occurred in your application. If you lcick continue, the application will ignore this erro and attempt to continue. If you click Quit. The appication will close immediately. (below are the details)
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception: The system cannot find the file specified
at System.Diagnostics.Process.StartWithCreateProcess(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at AthenaUnlocker.Form1.runExecutable(String path, String args, String wdir)
at AthenaUnlocker.Form1.button2_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
zip
Assembly Version: 0.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

Same issue
Am currently trying to run from the SD card after updating .NET. Keep you posted

Can't get past the .NET error despite reloading latest version of .NET
Suggestions anyone?

alerner1 said:
I get the following error after I finish the radio patch and it trys to run athen unlock.exe
Unhandled exception has occurred in your application. If you lcick continue, the application will ignore this erro and attempt to continue. If you click Quit. The appication will close immediately. (below are the details)
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception: The system cannot find the file specified
at System.Diagnostics.Process.StartWithCreateProcess(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at AthenaUnlocker.Form1.runExecutable(String path, String args, String wdir)
at AthenaUnlocker.Form1.button2_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
zip
Assembly Version: 0.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
Click to expand...
Click to collapse
And NOW?????????

[Q] Rooting troubles

Hello,
I was looking for some help. I was using Perception 9.5 for several months, but decided it was time to change. I used Odin to wipe my Captivate. Now I'm trying to re-root so I can flash Serendipity. I've been running into some trouble getting my phone rooted again though. I've tried several different ways. Most recently, I tried the "One click root" format. When I get to the "root" click, it gives me back "Unhandled exception has occured in your application...
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception (0x80004005): The system cannot find the file specified
at System.Diagnostics.Process.StartWithShellExecuteEx(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at System.Diagnostics.Process.Start(ProcessStartInfo startInfo)
at WindowsApplication1.Form1.Button1_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
----------------------------------------
Galaxy One Click Root
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/Collin/One%20click%20root/Galaxy_One-Click_Root.exe
----------------------------------------
Microsoft.VisualBasic
Assembly Version: 10.0.0.0
Win32 Version: 10.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualBasic/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualBasic.dll
----------------------------------------
System
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Core
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
----------------------------------------
System.Windows.Forms
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
System.Runtime.Remoting
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Runtime.Remoting/v4.0_4.0.0.0__b77a5c561934e089/System.Runtime.Remoting.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box."
I also decided to try "Chaos Central"'s Captivate root from Android forums. I renamed the files to update.zip, but can't figure out where to copy them to.
Any help would be appreciated. Thanks a lot.

xThaNaturalx said:
Hello,
I was looking for some help. I was using Perception 9.5 for several months, but decided it was time to change. I used Odin to wipe my Captivate. Now I'm trying to re-root so I can flash Serendipity. I've been running into some trouble getting my phone rooted again though. I've tried several different ways. Most recently, I tried the "One click root" format. When I get to the "root" click, it gives me back "Unhandled exception has occured in your application...
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception (0x80004005): The system cannot find the file specified
at System.Diagnostics.Process.StartWithShellExecuteEx(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at System.Diagnostics.Process.Start(ProcessStartInfo startInfo)
at WindowsApplication1.Form1.Button1_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
----------------------------------------
Galaxy One Click Root
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/Collin/One%20click%20root/Galaxy_One-Click_Root.exe
----------------------------------------
Microsoft.VisualBasic
Assembly Version: 10.0.0.0
Win32 Version: 10.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualBasic/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualBasic.dll
----------------------------------------
System
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Core
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
----------------------------------------
System.Windows.Forms
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
System.Runtime.Remoting
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Runtime.Remoting/v4.0_4.0.0.0__b77a5c561934e089/System.Runtime.Remoting.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box."
I also decided to try "Chaos Central"'s Captivate root from Android forums. I renamed the files to update.zip, but can't figure out where to copy them to.
Any help would be appreciated. Thanks a lot.
Click to expand...
Click to collapse
I guess the first questions are,
did you flash back to JF6? did you do a Master Clear? Which version of Odin did you use?
I use One Click all the time, and have no issues at all
Edit** Oh yeah, have you enabled debugging on your device?

why are you even bothering to go through the trouble of rooting?
there are literally thousands of copies of the update.zip floating around here that you need in order to boot straight into CWM....in fact, heres another one
you dont even need to boot into your stock 2.1 in order to begin flashing...

I already got through the master clear with Odin3, so that wasn't a problem. It's just getting the root files to read that I'm having trouble with.
I was rooting because I need a root for Titanium backup. I have all my apps saved to that, and I will need to re-install them all once I get a new ROM flashed. What does that zip file do?

xThaNaturalx said:
I already got through the master clear with Odin3, so that wasn't a problem. It's just getting the root files to read that I'm having trouble with.
I was rooting because I need a root for Titanium backup. I have all my apps saved to that, and I will need to re-install them all once I get a new ROM flashed. What does that zip file do?
Click to expand...
Click to collapse
that zip file is clockworkmod recovery
if you need to root to do a TiBu, have you tried SuperOneClick?
http://forum.xda-developers.com/showthread.php?t=803682
enable usb debugging

I'm sorry, that's what the error was from. The big one that I listed was the error that I received from SuperOneClick. I can't figure out where to go from there.

You do not need to root. Use the clockwork mod update.zip posted on this thread. Reinstall packages twice, install zip from SD, choose, flash rom. Done
Sent from my Captivate using XDA Premium App

Am I supposed to be copying the zip to the internal or external SD then?

Okay, I did install, choose, then it has "meta-inf", "res", or "sbin". Which do I choose?

xThaNaturalx said:
Okay, I did install, choose, then it has "meta-inf", "res", or "sbin". Which do I choose?
Click to expand...
Click to collapse
please step away from your captivate
you didnt 'install' anything. copy the .zip to your internal sdcard....reboot into recovery, reinstall packages, it will reboot back into recovery, reinstall packages again and you will be in clockworkmod recovery
THIS WILL NOT DO A TITANIUM BACKUP FOR YOU!
if you really need the TIBU, i suggest you fix your java problems on your computer

mcord11758 said:
You do not need to root. Use the clockwork mod update.zip posted on this thread. Reinstall packages twice, install zip from SD, choose, flash rom. Done
Sent from my Captivate using XDA Premium App
Click to expand...
Click to collapse
This is what I was doing. I reinstalled packages twice. Then i Did "install zip from sdcard", then "choose zip from sdcard", and then I don't know where to go from there.

xThaNaturalx said:
This is what I was doing. I reinstalled packages twice. Then i Did "install zip from sdcard", then "choose zip from sdcard", and then I don't know where to go from there.
Click to expand...
Click to collapse
when you select 'choose zip from sdcard' you point it to the rom you want to install.
i would highly suggest you read a little more before you break your phone....you dont sound too confident

That's what I've been trying to do. I'm not very confident at all about it. But I was following what he said in reply to your zip file.

xThaNaturalx said:
That's what I've been trying to do. I'm not very confident at all about it. But I was following what he said in reply to your zip file.
Click to expand...
Click to collapse
from what it sounds like, you unzipped the rom somewhere?
you dont unzip anything when it comes to flashing....you just point it to the actual ZIP file to flash

Pirateghost said:
from what it sounds like, you unzipped the rom somewhere?
you dont unzip anything when it comes to flashing....you just point it to the actual ZIP file to flash
Click to expand...
Click to collapse
I didn't end up unzipping it. I didn't finish the last step of his process because I couldn't figure out what the last one was and didn't want to mess it up. Thank you again for all your help so far though.

xThaNaturalx said:
I didn't end up unzipping it. I didn't finish the last step of his process because I couldn't figure out what the last one was and didn't want to mess it up. Thank you again for all your help so far though.
Click to expand...
Click to collapse
his last step is 'flash rom'
what is confusing about that...point the 'choose zip' to the rom.zip thats on your internal sdcard.....select it and thats it.....it will flash the rom. then you reboot and you have new rom

Pirateghost said:
his last step is 'flash rom'
what is confusing about that...point the 'choose zip' to the rom.zip thats on your internal sdcard.....select it and thats it.....it will flash the rom. then you reboot and you have new rom
Click to expand...
Click to collapse
Well I just successfully got the root complete and Serendipity flashed. Thank you for all your help.

[ROM] 5.1.* CyanogenMod 12.1

Hi, if anyone would like to run a 5.1.x Google OS on a Archos G9 80S device (and currently basically verified only with this), download and extract the file
16_12_2015-16_26_24
Installation (tested only with linux) :
- reboot into SDE menu and under "Format System" perform a "Reset Android & Storage" to clear all data of previous installations (this is really important for the first installation. Updating a existing installation (same major version) doesn't require this step !).
- reboot into SDE menu and under Developer Edition Menu -> "Export Data Partition"
- mount this usb drive
Code:
sudo mkdir <Mount_Path>/local
sudo cp archos.ext4.update <Mount_Path>/local/archos.ext4
sudo sync
sudo umount <Mount_Path>
- wait until the unmount process is done
- reboot into SDE menu and under Developer Edition Mernu , Flash Kernel and Initramfs : copy zImage and initramfs.cpio.lzo on the new driver that appears on desktop/laptop
- Wait for reboot your devices : after reboot you can see Android prepares the system for a while .....be patient at least ~20 minutes for the first run!
!!Update!!: If you have already installed CM12.0 then it may possible that you don't have to delete the data partition. You only have to copy the kernel/initramfs and ext4 file. I use the command for the last step:
Code:
adb push archos.ext4.update /data/media/ && adb reboot
What's new ?
------------ since 16_12_2015-16_26_24 -------------
Added usual CM updates. -> Also this release include the latest security fixes.
------------ since 05_08_2015-05_48_32 -------------
Added usual CM updates. (See included changelog for details) -> Also this release include the latest security fixes.
Added the 99Performance file from BlackGunZ Big thanks!
------------ since 31_05_2015-19_39_10 -------------
Added usual CM updates. (See included changelog for details)
Add *some* memory improvements, suggested by trevd (big thanks!)
*Maybe last release*
------------ since 23_04_2015-22_05_13 -------------
Initial release.
Re-Enabled Non-PIE Support to support the gps module.
Rebuild: All used revisions for this release are stored in a separate folder in the archive.
Additions:
Archos Control Panel App from @mordesku: http://forum.xda-developers.com/showpost.php?p=47789812&postcount=88
Thanks: @stargo @Hashcode @trevd
@CM community @all the cool omap4 hackers where I taken some code and inspirations !!!
Without these peoples, It would not so easy to make some (working) builds of the CM-12.1.
Archive:
31_05_2015-19_39_10
23_04_2015-22_05_13
XDA:DevDB Information
Archos G9 CyanogenMod 12.1, ROM for the Archos Gen9
Contributors
Quallenauge
ROM OS Version: 5.1.x Lollipop
ROM Kernel: Linux 3.0.x
Based On: Cyanogenmod
Version Information
Status: Alpha
Created 2015-04-24
Last Updated 2015-04-24

Thanks for keeping this old tablet going! I'll give it a try this weekend. :good:

jawiler said:
Thanks for keeping this old tablet going! I'll give it a try this weekend. :good:
Click to expand...
Click to collapse
Hi Quallenauge,
I've tried installing this version, but it just goes to a black screen for over 1/2-3/4 hour. I've tried downloading from both sites and checked the MD5SUMs and everything checks out. I went with a clean install.. I've installed your previous versions without any problems. Any ideas?
thanks
Nevermind, I tried a different computer and it worked this time

jawiler said:
Hi Quallenauge,
I've tried installing this version, but it just goes to a black screen for over 1/2-3/4 hour. I've tried downloading from both sites and checked the MD5SUMs and everything checks out. I went with a clean install.. I've installed your previous versions without any problems. Any ideas?
thanks
Nevermind, I tried a different computer and it worked this time
Click to expand...
Click to collapse
Mostly this error comes into play if the kernel&initramfs step or the update package is transferred and the mass storage drive is not cleanly unmounted.

@Quallenauge I knew I should have waited as I've just built cm-12.0 .... I even used your build environment script. Slightly unorthodox but it gets the Job done :good:
Anyway couple of notes from my side .. a bit of dex_preopting does wonders for the boot time
In the full_archos_g9.mk or similar
Code:
WITH_DEXPREOPT := true
WITH_DEXPREOPT_PIC := true
PRODUCT_DEX_PREOPT_BOOT_FLAGS := --compiler-filter=everything
PRODUCT_DEX_PREOPT_DEFAULT_FLAGS := --compiler-filter=everything
$(call add-product-dex-preopt-module-config,services,--compiler-filter=everything)
Not 100% sure that WITH_DEXPREOPT_PIC is required I threw it in anyway...
I also read up on low memory optimizations ( tricks/hacks ) , dropped all the wallpapers and a ton other other apps that I'm not using
It's pretty smooth ... That can be done at runtime by anyone who is feeling brave .
Hackon folks!
trevd

trevd said:
@Quallenauge I also read up on low memory optimizations ( tricks/hacks ) , dropped all the wallpapers and a ton other other apps that I'm not using. It's pretty smooth ... That can be done at runtime by anyone who is feeling brave .
Click to expand...
Click to collapse
Hi @trevd, I always follow your advice therefore I wonder what changes have you applied to optimize this rom? Could you give us any clue?
Thanks in advance

@Quallenauge First, thank you for your great port and efforts ! God bless you.
I found how to fix the root problem by doing some researches. For so, I edited the following line persist.sys.root_access which is present in build.prop file like this :
Code:
persist.sys.root_access=1
After a reboot, my tablet is correctly rooted and Archos Control Panel enables normally the deep sleep mode at boot.
Have a good day !

Hi! Any chance, to use working USB Stick?

BlackGunZ said:
I found how to fix the root problem by doing some researches. For so, I edited the following line persist.sys.root_access which is present in build.prop file like this
Click to expand...
Click to collapse
Hey, could you explain how you do that?
I have CM 12.1 installed on my Archos 80 G9, ADB is working and when I use 'adb shell' I'm supposedly root but can not write to /system.
I can pull the build.prop and change it, but I don't know how to put it back onto /system.

esque said:
Hey, could you explain how you do that?
I have CM 12.1 installed on my Archos 80 G9, ADB is working and when I use 'adb shell' I'm supposedly root but can not write to /system.
I can pull the build.prop and change it, but I don't know how to put it back onto /system.
Click to expand...
Click to collapse
Of course ! The most secure method is to edit the build.prop with CM File Manager.
Before, using ADB put this command after "adb shell" to mount your /system partition RW. After, do the steps I said below :
Code:
mount -o remount,rw /
First, open the file manager. Then, access to the app's options by taping on its icon at the left and choosing after that its settings icon, which is present at the left down side. Go to Advanced section and tap on Access mode next, choose Root access by this way the app will ask root permissions and a pop-up will appear to accept it. You will be redirected to the root (/ directory) of your Archos, scroll down again and go to /system directory. Screenshots :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Secondly, tap on your build.prop file and open it with the file manager's text editor. Choose the line persist.sys.root_access, delete the "3" value and put "1" instead. Screenshots :
Finally, save the file and reboot your phone. Voilà !

esque said:
I can pull the build.prop and change it, but I don't know how to put it back onto /system.
Click to expand...
Click to collapse
Do not forget to change file ownership and permission after pushing it back - or else you'll get a bootloop.
Since you do not know how to remount filesystem, I'd second @BlackGunZ and recommend using any root file editor on android to avoid bootloops and reflashing android (as opposed to adb pull/push).

Bor-ka said:
Do not forget to change file ownership and permission after pushing it back - or else you'll get a bootloop.
Since you do not know how to remount filesystem, I'd second @BlackGunZ and recommend using any root file editor on android to avoid bootloops and reflashing android (as opposed to adb pull/push).
Click to expand...
Click to collapse
That's why I suggested him to use CM File Manager, you're right sir.

@Quallenauge
JustArchi updated his ArchiDroid Optimizations for Lollipop (CyanogenMod). Can they be useful ?

I would really like to try this rom, can anyone help me with a step by step guild for installation, kinda new to installing in this fashion.
i ran the wubi installer to dual boot windows/linux
using ubuntu desktop.
need to know what i need to install prior and how to install it.
Pm me please, i don't want to mock-up the development page
thanks in advance
am i using terminal and going to the usb directory then using these commands?
- mount this usb drive
Code:
sudo mkdir <Mount_Path>/local
sudo cp archos.ext4.update <Mount_Path>/local/archos.ext4
sudo sync
sudo umount <Mount_Path>

@toolhas4degrees
For Windows, check the quote below and I can confirm that it works (I always use it), but for Linux I can't provide you a help as I don't have it.
taninos said:
Install this rom or other roms using Windows is pretty easy with Ext2Fsd Open Source Project ( it works over Win2k, Winxp, Vista, Win7, Win8, Server 2003, Server 2008/R2). Install Ext2Fsd on your PC and follow the next steps below to achieve this purpose. Neither this tablet drivers nor ADB nor a linux virtualized on Windows are needed.
Steps:
00 install Ext2Fsd
01 reboot into SDE menu and under "Format System" perform a "Reset Android & Storage" to clear all data of previous installations (this is really important!)
02 reboot into SDE menu and under Developer Edition Mernu -> "Export Data Partition"
03 connect your Tablet with your PC
04 start Ext2Fsd (ext2 volume manager interface). You should see your local drives and a extra one which is the Linux partition
05 mark that partition and press F7
06 start the service and be sure to check the "Enable writing support for ext3 volumes" and uncheck "Mount all volumes in read-only mode. Press apply
07 again mark your linux partition and press F3 and uncheck "Mount volume in read only mode"
08 now you should see the partition under "myComputer". Open it and if you reseted "Reset Android & Storage" you should see 2 Folders ("media" and "lost+found")
09 make a new folder called "local"
10 rename the archos.ext4.update to archos.ext4 and copy it into "local" folder
11 unmount the linux partition as you would do with any usb drive and then press ok on your tablet
12 go to "Developer Edition Menu" and choose "Flash Kernel and Initramfs"
13 a new drive will appear under "my computer". Copy zImage and initramfs.cpio.lzo to it and press ok
14 reboot your tablet and after a couple of seconds you should see the Archos logo and then Cyanogen logo
Click to expand...
Click to collapse

BlackGunZ said:
For Windows, check the quote below and I can confirm that it works...
Click to expand...
Click to collapse
It is a tad incomplete
11a. go to "Developer Edition Menu" and choose "Remove android kernel" (if not present - skip this step)

Last release? How about working USB stick?

BlackGunZ said:
Of course ! The most secure method is to edit the build.prop with CM File Manager.
Before, using ADB put this command after "adb shell" to mount your /system partition RW. After, do the steps I said below :
Code:
mount -o remount,rw /
First, open the file manager. Then, access to the app's options by taping on its icon at the left and choosing after that its settings icon, which is present at the left down side. Go to Advanced section and tap on Access mode next, choose Root access by this way the app will ask root permissions and a pop-up will appear to accept it. You will be redirected to the root (/ directory) of your Archos, scroll down again and go to /system directory. Screenshots :
Secondly, tap on your build.prop file and open it with the file manager's text editor. Choose the line persist.sys.root_access, delete the "3" value and put "1" instead. Screenshots :
Finally, save the file and reboot your phone. Voilà !
Click to expand...
Click to collapse
Hi
I've tried your method but I can't select root access in cm file manager. It does not work. How can I do ? Any idea ?
Thanks in advance
Ladalgigi
Envoyé de mon ARCHOS 101G9 en utilisant Tapatalk

sashokmc said:
Last release? How about working USB stick?
Click to expand...
Click to collapse
The last release is the one which is present in the OP, for an update we have to wait ! I didn't test the USB stick, sorry. ^^'
ladalgigi said:
Hi
I've tried your method but I can't select root access in cm file manager. It does not work. How can I do ? Any idea ?
Thanks in advance
Ladalgigi
Envoyé de mon ARCHOS 101G9 en utilisant Tapatalk
Click to expand...
Click to collapse
Exit CM File Manager, go to Settings, Developer Options and turn off the root permissions. Then, switch on again the root access to "ADB and applications" and try again

BlackGunZ said:
The last release is the one which is present in the OP, for an update we have to wait ! I didn't test the USB stick, sorry. ^^'
Exit CM File Manager, go to Settings, Developer Options and turn off the root permissions. Then, switch on again the root access to "ADB and applications" and try again
Click to expand...
Click to collapse
Thank you very much ! It works !
Very great ROM
Ladalgigi
Envoyé de mon ARCHOS 101G9 en utilisant Tapatalk

Nokia OST couldnt run... pops microsoft .net framework error!

Hello,
i tried to launch OST but popping error... i dnt know why its like dat and i have searched online for help but none gotten yet. i have attached screenshots of the error here too!
i have windows 10 pro/64bits. i need help please!
thanks...

whalesplaho said:
Hello,
i tried to launch OST but popping error... i dnt know why its like dat and i have searched online for help but none gotten yet. i have attached screenshots of the error here too!
i have windows 10 pro/64bits. i need help please!
thanks...
Click to expand...
Click to collapse
Could you post all text information about the details of the error? (Right click, select all, copy)
Are you running the tool with administrative elevation?

dbpm1 said:
Could you post all text information about the details of the error? (Right click, select all, copy)
Are you running the tool with administrative elevation?
Click to expand...
Click to collapse
here is tha error code..... thanks big!
Im running the tool without administrative elevation.
I have net framework v4.7 installed.
Code:
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.NullReferenceException: Object reference not set to an instance of an object.
at MainForms.Form1.DisableOptions()
at MainForms.Form1.Form1_Load(Object sender, EventArgs e)
at System.Windows.Forms.Form.OnLoad(EventArgs e)
at System.Windows.Forms.Form.OnCreateControl()
at System.Windows.Forms.Control.CreateControl(Boolean fIgnoreVisible)
at System.Windows.Forms.Control.CreateControl()
at System.Windows.Forms.Control.WmShowWindow(Message& m)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ScrollableControl.WndProc(Message& m)
at System.Windows.Forms.ContainerControl.WndProc(Message& m)
at System.Windows.Forms.Form.WmShowWindow(Message& m)
at System.Windows.Forms.Form.WndProc(Message& m)
at MainForms.Form1.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
OnlineUpdateTool
Assembly Version: 6.0.4.0
Win32 Version: 6.0.4
CodeBase: file:///C:/Program%20Files%20(x86)/OST%20LA/OnlineUpdateTool.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Configuration
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Configuration/2.0.0.0__b03f5f7f11d50a3a/System.Configuration.dll
----------------------------------------
System.Xml
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Xml/2.0.0.0__b77a5c561934e089/System.Xml.dll
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
MRG.Controls.UI
Assembly Version: 1.0.4854.21889
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Program%20Files%20(x86)/OST%20LA/MRG.Controls.UI.DLL
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

@bidhata @hikari_calyx @dbpm1 and others please help..... Thanks!!!

whalesplaho said:
System.NullReferenceException: Object reference not set to an instance of an object.
Click to expand...
Click to collapse
@whalesplaho I could not reproduce the error on two computers which i have tested.. but from what I could gather information about the error referenced above, there may be a problem with your .net install.
I've found two utilities that may help you fix the issue, but they should only point to problems on the .net installation, not directly solve them! You may run them just to have information on which version is crippled and then you should uninstall and install again.
Raymondcc .NET Detector
One way to check which versions of .NET are installed is through the system registry. If a .NET package is installed, its information should be correctly entered in the registry. We decided to use this method and create a little tool which does the plain and simple task of telling you which versions of .NET you have installed.
The tool couldn’t be simpler to use, just run the executable and it will tell you which .NET’s you have by showing them in dark text, the grayed out entries aren’t installed. Clicking on a non installed package will take you to its download page at Microsoft. The information from the window is copied to the clipboard to paste into help files etc. The program is able to detect .NET Frameworks from 1.0 up to the latest 4.7.2 (including versions specific to Windows 10), is portable and works on Windows XP and above.
Read More: https://www.raymond.cc/blog/how-to-...osoft-net-framework-is-installed-in-computer/
Download: https://www.raymond.cc/blog/download/did/1741/
Click to expand...
Click to collapse
.NET Framework Setup Verification Utility.
The .NET Framework Setup Verification Utility by Aaron Stebner is a very small and portable tool at only 272KB in size that you can use to verify the presence of files, directories, registry keys and values for the .NET Framework that is installed in your Windows computer. The latest version of .NET Framework Setup Verification Utility is able to automatically perform a set of steps to verify the installation state of the following .NET Frameworks:
.NET Framework 1.0
.NET Framework 1.1
.NET Framework 1.1 SP1
.NET Framework 2.0
.NET Framework 2.0 SP1
.NET Framework 2.0 SP2
.NET Framework 3.0
.NET Framework 3.0 SP1
.NET Framework 3.0 SP2
.NET Framework 3.5
.NET Framework 3.5 SP1
.NET Framework 4 Client
.NET Framework 4 Full
.NET Framework 4.5
Only the .NET Framework that the utility detects on the computer will be listed for verification so you won’t be seeing all of the above versions of the .NET Framework on the program. To verify the install state of a .NET Framework, simply select the version at the drop down box and click the Verify Now button. If the current status shows “Product verification succeeded”, then it means no problem but if you get a failed message, then you can consider reinstalling the .NET Framework version that has failed the verification.
Read More: https://www.raymond.cc/blog/net-framework-setup-verification-utility/
Download: https://www.raymond.cc/blog/download/did/2148/
Click to expand...
Click to collapse
If you have problems uninstalling or repairing, follow the tips here: https://www.raymond.cc/blog/uninstall-microsoft-net-framework-with-aaron-stebner-cleanup-tool/
Remember to reply if the issue was solved or not for future reference:good:
Good luck mate!

Tried everything and other method but no luck... I installed on a friends Windows 7 Ultimate and works very well!!!
Really don't know why its not working on my laptop... Really frustrating!!!

whalesplaho said:
Tried everything and other method but no luck... I installed on a friends Windows 7 Ultimate and works very well!!!
Really don't know why its not working on my laptop... Really frustrating!!!
Click to expand...
Click to collapse
That's really bad man, there must be something wrecked with .net on that laptop!
Can you run other .net dependant apps? Like Paint.net for example: https://www.getpaint.net/

dbpm1 said:
That's really bad man, there must be something wrecked with .net on that laptop!
Can you run other .net dependant apps? Like Paint.net for example: https://www.getpaint.net/
Click to expand...
Click to collapse
I have net framework working on my laptop... I have Paint.net app

Same problem here

V1c70rs said:
Same problem here
Click to expand...
Click to collapse
Had to reformat my laptop...

whalesplaho said:
Had to reformat my laptop...
Click to expand...
Click to collapse
Reformatting isn't a proper solution. Anyways, the error changed into "Culture id 3072 isn't a supported culture" when i updated OST LA to 6.37. After googling a bit, found out culture problem is related to Region and Language of Windows 10. So changed Region and Language to United States English even though I am not in USA. That got rid of the Culture problem and OST 6.37 started up fine but this version needs needed id and password. So uninstalled it, installed 6.04 version and it started up fine.
So, in short, the Solution is;
Change Region and Language to United States and United States English respectively.

This
Mist978 said:
Reformatting isn't a proper solution. Anyways, the error changed into "Culture id 3072 isn't a supported culture" when i updated OST LA to 6.37. After googling a bit, found out culture problem is related to Region and Language of Windows 10. So changed Region and Language to United States English even though I am not in USA. That got rid of the Culture problem and OST 6.37 started up fine but this version needs needed id and password. So uninstalled it, installed 6.04 version and it started up fine.
So, in short, the Solution is;
Change Region and Language to United States and United States English respectively.
Click to expand...
Click to collapse
This was the solution for me. Had been tearing my hair out because of this error. Just changed my region and boom! Thank you!

Mist978 said:
Reformatting isn't a proper solution. Anyways, the error changed into "Culture id 3072 isn't a supported culture" when i updated OST LA to 6.37. After googling a bit, found out culture problem is related to Region and Language of Windows 10. So changed Region and Language to United States English even though I am not in USA. That got rid of the Culture problem and OST 6.37 started up fine but this version needs needed id and password. So uninstalled it, installed 6.04 version and it started up fine.
So, in short, the Solution is;
Change Region and Language to United States and United States English respectively.
version 6.1.2 solved it for me.
Click to expand...
Click to collapse

Question Bricked with Black Screen. See on windows devices list account not ADB fastboot

My phone is has an unlocked bootloader, I had TWRP but i think i mistakenly formatted the recovery partition.
Now my phone is black screen only. It makes a noise when connected to PC but thats all. I have tried abd devices nothig listed
I tried me flash tool but it cant install driver -
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.IO.DirectoryNotFoundException: Could not find a part of the path 'C:\Users\n\Desktop\folder\MiFlash20181115\log\[email protected]'.
at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy, Boolean useLongPath, Boolean checkHost)
at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share, Int32 bufferSize)
at XiaoMiFlash.code.Utility.Log.w(String msg, Boolean throwEx)
at XiaoMiFlash.code.Utility.Log.w(String msg)
at XiaoMiFlash.MainFrm.RefreshDevice()
at XiaoMiFlash.MainFrm.btnRefresh_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4515.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
----------------------------------------
XiaoMiFlash
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/n/Desktop/folder/MiFlash20181115/XiaoMiFlash.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4550.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4536.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Drawing
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4395.0 built by: NET48REL1LAST_B
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
MiUSB
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/n/Desktop/folder/MiFlash20181115/MiUSB.DLL
----------------------------------------
System.Management
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4435.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Management/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Management.dll
----------------------------------------
System.Configuration
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4341.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Configuration/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Configuration.dll
----------------------------------------
System.Core
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4536.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
----------------------------------------
System.Xml
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4161.0 built by: NET48REL1
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Xml/v4.0_4.0.0.0__b77a5c561934e089/System.Xml.dll
----------------------------------------
Accessibility
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4161.0 built by: NET48REL1
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/Accessibility/v4.0_4.0.0.0__b03f5f7f11d50a3a/Accessibility.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
Any tips on how to recover this situation

If you have a black screen it looks you only can use EDL (testpoint) mode to recover the phone.
In that case you problably need an engineering rom or patched firehose file to pass the Mi authentication.
Maybe a modded Miflash tool without authentification could work too.
​
(For Poco M3 there is a description how you can do this)

I cannot strip open my phone its only a month old.
Elinx said:
If you have a black screen it looks you only can use EDL (testpoint) mode to recover the phone.
In that case you problably need an engineering rom or patched firehose file to pass the Mi authentication.
Maybe a modded Miflash tool without authentification could work too.
​
(For Poco M3 there is a description how you can do this)
Click to expand...
Click to collapse
I cannot strip open my phone its only a month old.

Unambiguous said:
I cannot strip open my phone its only a month old.
Click to expand...
Click to collapse
Then only you can contact the seller or Xiaomi service center

Unambiguous said:
I cannot strip open my phone its only a month old.
I cannot strip open my phone its only a month old.
Click to expand...
Click to collapse
Surely you can get to EDL mode without opening phone, there is a few ways. Have you tried reinstalling with miflash, relocking bootloader?, are you saying that your pc is not detecting the device at all.

Unambiguous said:
I cannot strip open my phone its only a month old.
Click to expand...
Click to collapse
You also can try first, very long power press. Without or with charger connected.
Sometimes this resolve the blackscreen problem.

Very frustrating. I don’t know what mode or state the phone is in. But it makes a noise usb noise when connected. Can’t detect in miflash
Will try another pc. If anyone is Will to join a zoom call to help
Am open to that too

gazza35 said:
Surely you can get to EDL mode without opening phone, there is a few ways. Have you tried reinstalling with miflash, relocking bootloader?, are you saying that your pc is not detecting the device at all.
Click to expand...
Click to collapse
Very frustrating. I don’t know what mode or state the phone is in. But it makes a noise usb noise when connected. Can’t detect in miflash
Will try another pc. If anyone is Will to join a zoom call to help
Am open to that too

Unambiguous said:
Very frustrating. I don’t know what mode or state the phone is in. But it makes a noise usb noise when connected. Can’t detect in miflash
Will try another pc. If anyone is Will to join a zoom call to help
Am open to that too
Click to expand...
Click to collapse
Have you just tried the long power button press, hold the power button for about 10 seconds, that should force a reboot, after a few minutes, connect to pc and try miflash again to see if it connects, you could also google XiaomiMiTool v2, that is another way of bypassing Xiaomi authorisations, has lots of useful tools to unlock \ Lock BL, flash etc, that may work for you, just need to get windows to detect the phone.
XiaoMiTool V2 Easy installation tool – Xiaomi Tools
xiaomitools.com

But overall the bad news is, the black screen of death as its known, usually requires a service at an outhorised repair shop, problem is youd probably have to pay, but i really dont think the charge would be too much, once repaired, i wouldnt mess with it again, id keep it stock.

gazza35 said:
But overall the bad news is, the black screen of death as its known, usually requires a service at an outhorised repair shop, problem is youd probably have to pay, but i really dont think the charge would be too much, once repaired, i wouldnt mess with it again, id keep it stock.
Click to expand...
Click to collapse
Ok thanks will have a look or send it for service
Phone only shows up on windows device manager not ADB list

I opened a service request via xiaomi uk and they are sending a jiffy bag. If they dont fix ill consider.
thanks for sharing. Am still miffed why i cant fix it myself.

Unambiguous said:
I opened a service request via xiaomi uk and they are sending a jiffy bag. If they dont fix ill consider.
thanks for sharing. Am still miffed why i cant fix it myself.
Click to expand...
Click to collapse
Glad youre getting it sorted. I know everyone likes to mess, flash, root, mod etc, but the development for this phone is patchy at best, nothing id consider a solid daily driver without issues, (NO disrespect to Devs intended because they work hard on these things for free). But my advice is simple, Unlock bootloader yes, but stick to to Stock Miui, whatever version you want to be on, at least ya guaranteed to still have a warranty and not worry about problems with bugs. Its a shame, but always issues with china phones, my previous was a Huawei, development again on that was really poor and you had to pay to unlock the bootloader. If youre looking for a phone you can constantly flash or mod then id suggest switch to a Samsung, me, im happy with Miui, especially for the macro camera and 4k video, its very good.

gazza35 said:
Glad youre getting it sorted. I know everyone likes to mess, flash, root, mod etc, but the development for this phone is patchy at best, nothing id consider a solid daily driver without issues, (NO disrespect to Devs intended because they work hard on these things for free). But my advice is simple, Unlock bootloader yes, but stick to to Stock Miui, whatever version you want to be on, at least ya guaranteed to still have a warranty and not worry about problems with bugs. Its a shame, but always issues with china phones, my previous was a Huawei, development again on that was really poor and you had to pay to unlock the bootloader. If youre looking for a phone you can constantly flash or mod then id suggest switch to a Samsung, me, im happy with Miui, especially for the macro camera and 4k video, its very good.
Click to expand...
Click to collapse
this will be my mums new phone...so good advise indeed.