Unbrick lg lte 2 f160 lsk qhsusb_dload no recovery no download mode

Unbrick lg lte 2 f160 lsk qhsusb_dload no recovery no download mode - LG Optimus 2x

I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
.
THATS ALL WHAT I HAVE FOR MY FRIENDS.
IF I HELPED YOU THEN PLZ PRAY FOR ME. THANKS ALOT

Thank you for providing the files! I have a bricked LG LTE2 F160K, which mode should I put the phone be?
My phone can still access download mode, and when I try to start up the tool, it just says "Failed during loading flash programmer"

bro if your download mode is working then you will have to flash kdz of your modal for f160k I think its 20k. you can find the latest kdz many sites. google it lg firmware you can find it on vietnam site lgviet.com

this programe is only for qhsusb_delod mode. no download no recovery state. if you have download mode then kdz is the way to unbrick

Help! "device was not found in dload trying flash programmer" i get this error

What kind of brick you have? Its qhsusb bulk mode. Then this guide will help you

what is "ion took"??
there are no "D1L(MSM8960 RR&G)" in the selection

muzammil457 said:
What kind of brick you have? Its qhsusb bulk mode. Then this guide will help you
Click to expand...
Click to collapse
test completed but my phone didn't enter to download mode
the driver name when i connect my LG is"QHSUSB_QLOAD"

why yu no reply??

Have you installed qualcm drivers first? If no then do it if yes then in board ap choose msm8960 it will work. But if doesnt then there is 1 more 8960 selection try that

Does this method works for a sony xperia ion which has the same problem????

ahamedlaheer said:
Does this method works for a sony xperia ion which has the same problem????
Click to expand...
Click to collapse
This programe is for qualcom devices. If your experia is qualcom based then it will work. But u need to find the files to flash doe your modalm I have loaded only f160 system files.

muzammil457 said:
Have you installed qualcm drivers first? If no then do it if yes then in board ap choose msm8960 it will work. But if doesnt then there is 1 more 8960 selection try that
Click to expand...
Click to collapse
yes i install it, i tried the other msm8960 but it doesn't work

Test point to force qhsusb-dload in LG F160s
mcycharles said:
Thank you for providing the files! I have a bricked LG LTE2 F160K, which mode should I put the phone be?
My phone can still access download mode, and when I try to start up the tool, it just says "Failed during loading flash programmer"
Click to expand...
Click to collapse
Dear all,
Can some one provide me the details of test points for LG F160s i want to force it, as m phone in dead alsmost,,,
i will b very thankful
Rizwan

Why u need to do that if u r not in hard brick state?

muzammil457 said:
I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
. THATS ALL WHAT I HAVE FOR MY FRIENDS.
I have F160L.i tried same as u mention,All proceger complete but no download mode no fastboot mode no LG logo.What to do now?still on qualcomm 9008
Click to expand...
Click to collapse

Hello all
If after restore aboot phone not power on
Need restore all this file: about, Backupgpt, boot, dbi, laf, Primarygpt, recovery, rpm, tz, sdl1, sdl2, sdl3 (one by one, not MIX!!!) and after restore last sdl3 power turn on!

muzammil457 said:
I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
.
THATS ALL WHAT I HAVE FOR MY FRIENDS.
IF I HELPED YOU THEN PLZ PRAY FOR ME. THANKS ALOT
Click to expand...
Click to collapse
any other link for qualcomm drivers?

Link is fine. U can download it from google.

Need some Help
My phone goes to Service Mode but not in Download mode.
Should i try this method?
And how i can find out my phone is S OR K OR L originally hardware based
Waiting for your answer .
My phone is dead since 1 month

Related

Guide Root and Unbrick Moto E3 Power (XT1706), For newbie

Firstly, I want to say ‘thankyou’ to pranaay saini and dr.faramroze. u guys are first man who post topic guide root and build specialy TWRP for Moto E3 Power. And now, I want to share my story about my process ‘rooting Moto E3 Power’ LoL :
*Note:
1/ Im a newbie, not a specialist about android phone or technician mobile. I just a person who curious ‘rooting android’ to make my phone can delete almost factory app not neccesary.LoL. Truly, I want to cheat mobile game =)).
2/ I had successful root HTC One M7 before, so Let’s see me have a little exp for Rooting . Then own the new Moto E3 Power and I want do the same HTC .
*My story:
I bought the new E3 Power on online store and Im going to root it. Unluckily, I forgot to ‘fastboot format userdata’ and this phone gonna ‘bootloop’ :v. I bring it to fix in small repair phone center (I already give them the stock rom), hope they can flash rom stock but they turn my phone into ‘hard bricked mode’ :v, less well they format S/N @@.
That’s a awful time in my life =)), I sent it back to store. Luckily, they accept to fix it cause I just used it for 2 days (actually I told them it was factory error) and maybe they believe it true ‘opsss! So sorry’.
After my phone fixed, I root it again, and this time I did really carefully so ‘Your device has rooted’ Bravo! =)). And ‘Peaceful time’ long last 4months, I just install SDMaid and run Luckypatcher to crack SDMaid FREE up to SDMaid PRO, and used SDMaid to cleanup the phone, then my phone run to error ‘com.android.phone had stoped’, and I also find many ways to fix this problem, almost solution on the internet I have try but it’s not working, the finnally option, I chose to ‘reset phone to factory’ . OOOPS! My phone got ‘Soft bricked’ =.=,unfortunately I had deleted file TWRP backup @@, then I tried to flash stock rom thought TWRP but it error =.=. At this moment, I think ‘prehap I bring it to store fix it again?’ . NOPE! Im looking on the internet to find out solution to fix it (just a few days before I write this topic), finally only way to fix that is ‘SP Flash Tool’ =)), and it work! .
*So it’s all my story when I come to E3 GOD Power =)). Sorry if it so drammatic and bad english :”>. U guys can skip that and go to Main Problem here:
== How to root Moto E3 Power (XT1706) ==
Plz follow step by step if u are new guys like me xD! (Picture guide bellow)
1/ Prepare: ADB (or minimal ADB) and ADB driver on ur PC (u can search on XDA forum to get link download – I recommend use minimal ADB).
2/ Get TWRP recovery and SuperSU from this link:
https://forum.xda-developers.com/showpost.php?p=69311942&postcount=22
copy file SuperSU to SDcard.
3/ On your phone, go to Setting > Choose About phone > roll down to last line > tap many times to set u up to Developer > then back so now u can see ‘Developer options’ line > go into it > swipe ON OEM Unlocking and USB Debugging.
4/ Now turn off power, after screen off hold Power button and Up Volume to boot ur phone into ‘fastboot mode’.
5/ Connect ur phone to PC and open ADB u install before (open ADB as administrator)
6/ Copy file TWRP recovery (*.img) u have download into folder ADB u install before. U can rename it to remember and type on ADB easier. (to me: rename it to recoverymoto.img)
7/ Execute the following comand on ADB:
- ‘fastboot devices’ >> its show u ur device connected to PC or not. If not, plz check adb driver.
- ‘fastboot oem unlock’ >> now on ur display phone have announce unlock YES/NO? follow instruction on display phone. YES to unlock.
- ‘fastboot format userdata’ >> make sure u do this command cause if not after u flash TWRP recovery and reboot system u gonna to stuck boot or boot loop.
- ‘fastboot flash recovery recovery.img’ >> its change Default recovery to TWRP recovery.
Well done! Now u successful to install TWRP.
8/ Now hold Power button and Up Volume to boot ur phone into ‘fastboot mode’ but not choose Fasboot mode, choose Recovery mode. It gonna turn into TWRP recovery display.
9/ Last step. In TWRP working display > choose Install > Select microSD > then u see file SuperSU in SDcard u copy in step 2 > choose file SuperSU and install it > after all done, reboot system and ENJOY ‘Your device has rooted’ .
*Note: If u reboot, it stuck at Moto logo, or boot loop. Plz Redo Step 4 to Step 9. If not, u need to comment and me and E3 power brother will help u
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
2/ Prepare MTKdriver (MediaTek driver) for ur PC, u can download on this link:
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033
https://androidmtk.com/download-mtk-usb-all-drivers
3/ After install all, open SPflash tool (dont plugin cable and phone to PC), just open flashtool and WARNING on tab Format, don’t Format if u don’t know how to use for what purpose! Cause if u format ur imei phone has gone :v…and u will find and learn how to use S/N tool or even bring it to change mainboard :v…. So DONT, just focus on tab Dowload.
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
6/ Congratulation! Ur phone back to Factory come out . hold the power button and ENJOY ur phone reborn .
*Note: during time flashing ROM, do not plugout cable.
Thanks for your reading!If u like this,give me 1 Thanks . Welcome all constructive comments to help me edit this topic more complete.

First of all I would like to say that @bopvnn luck is not on your side :silly: second of all , all the work was done by @dr.faramroze I just made the tutorial a bit easier .

pranaay saini said:
First of all I would like to say that @bopvnn luck is not on your side :silly: second of all , all the work was done by @dr.faramroze I just made the tutorial a bit easier .
Click to expand...
Click to collapse
i dont know what u mean "lucky is not on my side" :-?

bopvnn said:
i dont know what u mean "lucky is not on my side" :-?
Click to expand...
Click to collapse
Meaning you have bad luck .

Hey, I see some guys on Youtube that said losing their IMEI after flashing stock rom using SP Flash Tool. How to restore it? The last time I use a Mediatek Device it was an Android One.

Removing battery wont help ,
bopvnn said:
Firstly, I want to say ‘thankyou’ to pranaay saini and dr.faramroze. u guys are first man who post topic guide root and build specialy TWRP for Moto E3 Power. And now, I want to share my story about my process ‘rooting Moto E3 Power’ LoL :
*Note:
1/ Im a newbie, not a specialist about android phone or technician mobile. I just a person who curious ‘rooting android’ to make my phone can delete almost factory app not neccesary.LoL. Truly, I want to cheat mobile game =)).
2/ I had successful root HTC One M7 before, so Let’s see me have a little exp for Rooting . Then own the new Moto E3 Power and I want do the same HTC .
*My story:
I bought the new E3 Power on online store and Im going to root it. Unluckily, I forgot to ‘fastboot format userdata’ and this phone gonna ‘bootloop’ :v. I bring it to fix in small repair phone center (I already give them the stock rom), hope they can flash rom stock but they turn my phone into ‘hard bricked mode’ :v, less well they format S/N @@.
That’s a awful time in my life =)), I sent it back to store. Luckily, they accept to fix it cause I just used it for 2 days (actually I told them it was factory error) and maybe they believe it true ‘opsss! So sorry’.
After my phone fixed, I root it again, and this time I did really carefully so ‘Your device has rooted’ Bravo! =)). And ‘Peaceful time’ long last 4months, I just install SDMaid and run Luckypatcher to crack SDMaid FREE up to SDMaid PRO, and used SDMaid to cleanup the phone, then my phone run to error ‘com.android.phone had stoped’, and I also find many ways to fix this problem, almost solution on the internet I have try but it’s not working, the finnally option, I chose to ‘reset phone to factory’ . OOOPS! My phone got ‘Soft bricked’ =.=,unfortunately I had deleted file TWRP backup @@, then I tried to flash stock rom thought TWRP but it error =.=. At this moment, I think ‘prehap I bring it to store fix it again?’ . NOPE! Im looking on the internet to find out solution to fix it (just a few days before I write this topic), finally only way to fix that is ‘SP Flash Tool’ =)), and it work! .
*So it’s all my story when I come to E3 GOD Power =)). Sorry if it so drammatic and bad english :”>. U guys can skip that and go to Main Problem here:
== How to root Moto E3 Power (XT1706) ==
Plz follow step by step if u are new guys like me xD! (Picture guide bellow)
1/ Prepare: ADB (or minimal ADB) and ADB driver on ur PC (u can search on XDA forum to get link download – I recommend use minimal ADB).
2/ Get TWRP recovery and SuperSU from this link:
https://forum.xda-developers.com/showpost.php?p=69311942&postcount=22
copy file SuperSU to SDcard.
3/ On your phone, go to Setting > Choose About phone > roll down to last line > tap many times to set u up to Developer > then back so now u can see ‘Developer options’ line > go into it > swipe ON OEM Unlocking and USB Debugging.
4/ Now turn off power, after screen off hold Power button and Up Volume to boot ur phone into ‘fastboot mode’.
5/ Connect ur phone to PC and open ADB u install before (open ADB as administrator)
6/ Copy file TWRP recovery (*.img) u have download into folder ADB u install before. U can rename it to remember and type on ADB easier. (to me: rename it to recoverymoto.img)
7/ Execute the following comand on ADB:
- ‘fastboot devices’ >> its show u ur device connected to PC or not. If not, plz check adb driver.
- ‘fastboot oem unlock’ >> now on ur display phone have announce unlock YES/NO? follow instruction on display phone. YES to unlock.
- ‘fastboot format userdata’ >> make sure u do this command cause if not after u flash TWRP recovery and reboot system u gonna to stuck boot or boot loop.
- ‘fastboot flash recovery recovery.img’ >> its change Default recovery to TWRP recovery.
Well done! Now u successful to install TWRP.
8/ Now hold Power button and Up Volume to boot ur phone into ‘fastboot mode’ but not choose Fasboot mode, choose Recovery mode. It gonna turn into TWRP recovery display.
9/ Last step. In TWRP working display > choose Install > Select microSD > then u see file SuperSU in SDcard u copy in step 2 > choose file SuperSU and install it > after all done, reboot system and ENJOY ‘Your device has rooted’ .
*Note: If u reboot, it stuck at Moto logo, or boot loop. Plz Redo Step 4 to Step 9. If not, u need to comment and me and E3 power brother will help u
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
2/ Prepare MTKdriver (MediaTek driver) for ur PC, u can download on this link:
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033
https://androidmtk.com/download-mtk-usb-all-drivers
3/ After install all, open SPflash tool (dont plugin cable and phone to PC), just open flashtool and WARNING on tab Format, don’t Format if u don’t know how to use for what purpose! Cause if u format ur imei phone has gone :v…and u will find and learn how to use S/N tool or even bring it to change mainboard :v…. So DONT, just focus on tab Dowload.
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
6/ Congratulation! Ur phone back to Factory come out . hold the power button and ENJOY ur phone reborn .
*Note: during time flashing ROM, do not plugout cable.
Thanks for your reading!If u like this,give me 1 Thanks . Welcome all constructive comments to help me edit this topic more complete.
Click to expand...
Click to collapse
everything you said is right except for you have to keep the battery inside and the phone switched
this will help
https://www.youtube.com/watch?v=W-bBhe3kp_8&t=327s

Will root will run on xt1700?
As in the title - Will the TWRP work with the XT1700?

Alcatraz_91 said:
everything you said is right except for you have to keep the battery inside and the phone switched
this will help
&t=327s
Click to expand...
Click to collapse
Bro my phone is vibrating and showing Moto logo and again vibrating and showing Moto logo...so I'm thinking that my phone is soft bricked after flashing twrp 3.1.1
When I try to flash stock using sp flash tool some error is showing 0*00... Will u plzzz help to get back my device..:crying::crying:

My internal storage is about nill...
But it is showing about 14 GB and the actual storage is now 774 mb....how to format it...I'm unable to format it with twrp plzzz help...it is showing storage is running out....plzzzzzz help me....

Manoj Kumar 9779 said:
My internal storage is about nill...
But it is showing about 14 GB and the actual storage is now 774 mb....how to format it...I'm unable to format it with twrp plzzz help...it is showing storage is running out....plzzzzzz help me....
Click to expand...
Click to collapse
Please do not private message me asking for help/assistance with your problems.
I will help anyone if asked correctly, in the correct way and in the correct place.
I will not answer to demanding messages or messages giving no information what so ever.
I'm a typical user, not a helpdesk.
You question is answered in this thread and the Q and A section.

Not able to roote3 power with build s144
Hi,
I have moto e3 power with build number xt1706_s144_170915_row. When i am rooting and installing twrp through fastboot method, after rooting the phone goes in bootloop. The same issue was happening with build s143, however i was able to successfully root for previous build s141. I am following the same method but failing now. Any help will be great

It's my first phone that I will root (moto e3 power)
But the main problem is that, I can't unlock the bootloader , i have used adb driver but after the "fastboot devices" command , my phone's starts in fastboot mode but the connection with my PC is lost. , so please give me the link of the minimal adb and the other moto e3 power driver that you have used to unlock

Jackyhost said:
It's my first phone that I will root (moto e3 power)
But the main problem is that, I can't unlock the bootloader , i have used adb driver but after the "fastboot devices" command , my phone's starts in fastboot mode but the connection with my PC is lost. , so please give me the link of the minimal adb and the other moto e3 power driver that you have used to unlock
Click to expand...
Click to collapse
STOCK ROM INSTALLATION WITH TWRP RECOVERY
Check this video
Without wiping your imei no flash stock rom
This method is find by me please share to others
:good:
---------- Post added at 06:06 PM ---------- Previous post was at 06:05 PM ----------
jigar191089 said:
Hi,
I have moto e3 power with build number xt1706_s144_170915_row. When i am rooting and installing twrp through fastboot method, after rooting the phone goes in bootloop. The same issue was happening with build s143, however i was able to successfully root for previous build s141. I am following the same method but failing now. Any help will be great
Click to expand...
Click to collapse
STOCK ROM INSTALLATION WITH TWRP RECOVERY
Check this video
Without wiping your imei no flash stock rom
This method is find by me please share to others
:good:

Note :-
It works only on S135 and S141
It does not work with S143 and S144
I don't know why

hey 'fastboot format userdata' command not working.. it says "Createprocess failed: system cannot find file specified. (2) cannot generate image for userdate" Kindly help I am noobie

kunal0303 said:
hey 'fastboot format userdata' command not working.. it says "Createprocess failed: system cannot find file specified. (2) cannot generate image for userdate" Kindly help I am noobie
Click to expand...
Click to collapse
use this adb... i too had the same issue......... it worked for me.....
https://forum.xda-developers.com/showthread.php?t=2588979

HELP!!!
i cant execute "fastboot reset userdata" it shows "cant find file specified" please help someone

bopvnn said:
Firstly, I want to say ‘thankyou’ to pranaay saini and dr.faramroze. u guys are first man who post topic guide root and build specialy TWRP for Moto E3 Power. And now, I want to share my story about my process ‘rooting Moto E3 Power’ LoL :
*Note:
1/ Im a newbie, not a specialist about android phone or technician mobile. I just a person who curious ‘rooting android’ to make my phone can delete almost factory app not neccesary.LoL. Truly, I want to cheat mobile game =)).
2/ I had successful root HTC One M7 before, so Let’s see me have a little exp for Rooting . Then own the new Moto E3 Power and I want do the same HTC .
*My story:
I bought the new E3 Power on online store and Im going to root it. Unluckily, I forgot to ‘fastboot format userdata’ and this phone gonna ‘bootloop’ :v. I bring it to fix in small repair phone center (I already give them the stock rom), hope they can flash rom stock but they turn my phone into ‘hard bricked mode’ :v, less well they format S/N @@.
That’s a awful time in my life =)), I sent it back to store. Luckily, they accept to fix it cause I just used it for 2 days (actually I told them it was factory error) and maybe they believe it true ‘opsss! So sorry’.
After my phone fixed, I root it again, and this time I did really carefully so ‘Your device has rooted’ Bravo! =)). And ‘Peaceful time’ long last 4months, I just install SDMaid and run Luckypatcher to crack SDMaid FREE up to SDMaid PRO, and used SDMaid to cleanup the phone, then my phone run to error ‘com.android.phone had stoped’, and I also find many ways to fix this problem, almost solution on the internet I have try but it’s not working, the finnally option, I chose to ‘reset phone to factory’ . OOOPS! My phone got ‘Soft bricked’ =.=,unfortunately I had deleted file TWRP backup @@, then I tried to flash stock rom thought TWRP but it error =.=. At this moment, I think ‘prehap I bring it to store fix it again?’ . NOPE! Im looking on the internet to find out solution to fix it (just a few days before I write this topic), finally only way to fix that is ‘SP Flash Tool’ =)), and it work! .
*So it’s all my story when I come to E3 GOD Power =)). Sorry if it so drammatic and bad english :”>. U guys can skip that and go to Main Problem here:
== How to root Moto E3 Power (XT1706) ==
Plz follow step by step if u are new guys like me xD! (Picture guide bellow)
1/ Prepare: ADB (or minimal ADB) and ADB driver on ur PC (u can search on XDA forum to get link download – I recommend use minimal ADB).
2/ Get TWRP recovery and SuperSU from this link:
https://forum.xda-developers.com/showpost.php?p=69311942&postcount=22
copy file SuperSU to SDcard.
3/ On your phone, go to Setting > Choose About phone > roll down to last line > tap many times to set u up to Developer > then back so now u can see ‘Developer options’ line > go into it > swipe ON OEM Unlocking and USB Debugging.
4/ Now turn off power, after screen off hold Power button and Up Volume to boot ur phone into ‘fastboot mode’.
5/ Connect ur phone to PC and open ADB u install before (open ADB as administrator)
6/ Copy file TWRP recovery (*.img) u have download into folder ADB u install before. U can rename it to remember and type on ADB easier. (to me: rename it to recoverymoto.img)
7/ Execute the following comand on ADB:
- ‘fastboot devices’ >> its show u ur device connected to PC or not. If not, plz check adb driver.
- ‘fastboot oem unlock’ >> now on ur display phone have announce unlock YES/NO? follow instruction on display phone. YES to unlock.
- ‘fastboot format userdata’ >> make sure u do this command cause if not after u flash TWRP recovery and reboot system u gonna to stuck boot or boot loop.
- ‘fastboot flash recovery recovery.img’ >> its change Default recovery to TWRP recovery.
Well done! Now u successful to install TWRP.
8/ Now hold Power button and Up Volume to boot ur phone into ‘fastboot mode’ but not choose Fasboot mode, choose Recovery mode. It gonna turn into TWRP recovery display.
9/ Last step. In TWRP working display > choose Install > Select microSD > then u see file SuperSU in SDcard u copy in step 2 > choose file SuperSU and install it > after all done, reboot system and ENJOY ‘Your device has rooted’ .
*Note: If u reboot, it stuck at Moto logo, or boot loop. Plz Redo Step 4 to Step 9. If not, u need to comment and me and E3 power brother will help u
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
2/ Prepare MTKdriver (MediaTek driver) for ur PC, u can download on this link:
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033
https://androidmtk.com/download-mtk-usb-all-drivers
3/ After install all, open SPflash tool (dont plugin cable and phone to PC), just open flashtool and WARNING on tab Format, don’t Format if u don’t know how to use for what purpose! Cause if u format ur imei phone has gone :v…and u will find and learn how to use S/N tool or even bring it to change mainboard :v…. So DONT, just focus on tab Dowload.
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
6/ Congratulation! Ur phone back to Factory come out . hold the power button and ENJOY ur phone reborn .
*Note: during time flashing ROM, do not plugout cable.
Thanks for your reading!If u like this,give me 1 Thanks . Welcome all constructive comments to help me edit this topic more complete.
Click to expand...
Click to collapse
Awesome post brother! I only wish I had simply read this post before messing up so much with my phone. Actually, I was messing with some magisk module (edxposed) whick bricked my device and got me stuck at a bootloop and with no recovery partition at all. (It erased my TWRP). So I used the sp flash tool and formatted the whole flash (at that time, I hadn't read this post of yours). Then I flashed my entire firmware back via the sp flash tool. So I thought that now my problem was fixed. But when I switched on my phone I saw my phone's IMEI Number gone! And the sim not working and showing invalid IMEI message. So I tried to find a fix on the internet and I found 2 solutions. First was using an app which requires the phone to support some mtk engineering mode. I followed the instructions and realised that maybe our phone Moto E3 Power doesn't support this mode. So I switched to the second solution, which required root access. So then I set off for rooting my newly unbricked phone. But I again did some mistakes:
1.) Allowed usb debugging and OEM unlocking in my phone's developer options in settings.
2.) I installed minimal ADB v1.4.3 on a windows 10 computer. Checked my phone's connection with the PC via ADB command adb devices. It worked showing some error initially (daemon not started.... Starting daemon...) and then showing some hex code signifying my device's successful connection with the PC.
3.) Used ADB command adb reboot bootloader to boot into fastboot mode. It worked too.
3.) Used fastboot command fastboot devices to check if my device is still being recognised as connected to the pc. Here came an error (the command didn't return any hex code like the adb command adb devices did. So I googled a solution which involves updating the "Android ADB interface" to "Android Bootloader interface" in the "Android device" submenu of the "Device Manager" window of the "control panel" of the pc, by updating its drivers using the "latest windows usb drivers" 8mb file which could be found very easily on the internet (searching solution for fastboot device drivers update on Google). {*Note: If you hadn't installed beforehand, any adb and fastboot drivers at all, then you will see "Other devices" submenu instead of the "Android device" submenu in the device manager window.
Also, you compulsively need to be in fastboot mode with your device attached to pc, in order to see this "other devices" submenu.} So now the fastboot devices command started working by showing the hex code like adb devices command did.
4.) Used fastboot oem unlock command to unlock the phone's bootloader. Pressed the volume up button of my phone as instructed by the warning message on my phone's screen. Unlock flow started in the minimal adb window in my pc. Finished successfully within 9-13 seconds. Another mistake now, after unlocking the bootloader, I forgot to format userdata.. Actually I didn't know about the fastboot format userdata command. I thought the fastboot -w reboot is the only way to format userdata (which wasn't working for me). Unaware of the fact that now I was going to experience a bootloop during rebooting my phone, I continued with the further steps.
5.) Used fastboot flash recovery recovery.img command to flash the unofficial twrp img which I had already placed in the minimal adb folder and renamed to recovery.img I used unofficial twrp v3.1.1 (by moderator) [which was working perfectly earlier on my phone] {link at bottom}. Successfully finished this step too. [You can use either of the two twrp: Dr. Faramroze (link provided by op) or moderator (link provided by me). Both are working fine]
6.) Used the fastboot reboot command (although it never works for me). It shows finished in the minimal adb cmd screen but the phone doesn't reboot. So I manually unplugged the device. Removed and reinserted the battery.
7.) Now rebooted to recovery screen and found the unofficial twrp successfully installed. [ Warning: After the 6th step, don't reboot your phone normally. Instead, boot into the fastboot window [hold power + vol. up] and select the boot into recovery option. This is required only for the first boot up process or else if you do a normal boot during the first boot, the stock recovery replaces our recently flashed custom recovery..
8.) Upon entering the twrp recovery during the first boot, I installed the magisk v19.3 zip I had in my external SD card. It's not necessary to root your phone right now, you may even do it later by simply rebooting from within the twrp, and later on entering recovery after your phone is all set and working and when you're free from other hassles. But I went for rooting during the first boot. And encountered an error something like: "Cannot mount data(0mb)" at the second last line. So, I could not root my phone. So I decided to root it later on and currently just have it switched on. So, I went for the reboot option in twrp.
9.) My phone started rebooting and got stuck at the boot screen with the tag Device unlocked at the lower left corner (indicating unlocked bootloader). But this was something familiar to me, I had already dealt with this error the previous time I rooted my phone. The solution was very simple. I just had to flash a no verity-otp-encrypt.zip file {included along with the twrp link} using the twrp recovery and then my device would boot properly, as it did the last time.
10.) I flashed the no verity-otp-encrypt.zip file from the twrp and got so many red line errors during the flash. (This didn't happen the last time). Every error had the same words, "cannot mount data (0mb)". So I went back to try rebooting again.
11.) Started rebooting again. This time the device didn't get stuck at boot screen, rather it went into a bootloop, rebooting again and again. Now maybe the no verity-otp-encrypt.zip file did its job and my device got free from the stuck at boot screen problem but simultaneously got caught by the bootloop error probably created due to not formatting the userdata after unlocking the bootloader. Or maybe the "cannot mount data (0mb) just ruined up my phone. Whatever the cause be, I just went for reflashing the entire firmware via the sp flash tool and temporarily forgetting all the bootloader unlocking, custom recovery, rooting, etc and live with an invalid IMEI phone without a working sim, until I find a solution on the internet.
12.) And then, I ended up here on this thread leaving my experience, and learning my mistakes from the OP's post. Very soon I will depart for the cyber cafe to try again without any mistakes this time.
At last thanks for this awesome thread.
And yes here's the link for the unofficial twrp 3.1.1 (by moderator) & the no verity-otp-encrypt.zip file:
https://drive.google.com/folderview?id=1-CHJtDUyPH1CJHebhKsUJz8SzKJAcDbv
---------- Post added at 12:56 PM ---------- Previous post was at 12:41 PM ----------
smug_loner said:
From where i can download fastboot file??
Click to expand...
Click to collapse
Search Google for "Moto E3 power firmware flash file" and you will come across websites providing the flash file. The file would have a name like "Motorola_Moto_E3_Power_XT1706_MT6735M_S135_161108_6.0.1.zip". The "S135" over here is the firmware version and will vary upon the version uploaded by the site. The latest version as of today is S152_190315. I somehow managed to download a S151 file and I forgot where I downloaded it from. But you can still go for older firmware versions, and then when you're done with all the flashing and rooting and all that and your phone starts up without any error, you can go for OTA updates from within the settings>about phone>system update.

bopvnn said:
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
Click to expand...
Click to collapse
S151 is newest (flash file available for download) for XT1706. [Actually S152 is latest but it's not yet available for download] So you succeeded maybe because you used the older version. Cause a guy commented that he couldn't root the newer versions but could root the older versions.
---------- Post added at 02:32 PM ---------- Previous post was at 02:25 PM ----------
bopvnn said:
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
Click to expand...
Click to collapse
Is it necessary to uncheck preload? If yes, I think you should highlight it. Anyway, I didn't uncheck preload and the flash successfully worked for me? So what difference does it count for? Please do notify us of its significance.
---------- Post added at 03:03 PM ---------- Previous post was at 02:32 PM ----------
bopvnn said:
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
Click to expand...
Click to collapse
I didn't remove my battery, sim or microsd card and everything worked fine for me. Also, I didn't connect my device to pc after pressing the download button in the sp flash tool. Here's what I did instead:
I kept the sp flash tool ready with all steps. Only pressing the download button remaining. Then I connected my device to the pc. As soon as you hear the device connected sound, press the download button. And the flashing process will start. If you get late in pressing the download button, you will hear another sound of device disconnected. Then you'll have to remove the usb from the device and replug it and go for trying again pressing the download button as soon as you hear the device connected sound.

Debrick Asus Zenfone 2, 100% Guarantee

***************************************************************BEST SOLUTION**********************************************************
hey guys!!!!!!!!
if all of the method over internet fails for you, then here comes mine method, working 100%
its the easiest method!!!!!!!
Prerequisite:
Download Asus Firmware Raw BAckup and EMMC Raw tool From Following Link:
https://drive.google.com/open?id=1z3IJ6YMUUdQSsXPdVAxJoD7iBettxpM1
Download Minitool Partition Wizard From Their Web!!!!!!!!
Now The Solution:
1. Connect Your Phone To Your PC,
2. Check If it is in QDLoader 9006 mode or 9008 Mode
3. IF u r in 9006 mode, Skip to step 5...
4. if u r in 9008 mode then, Install Minitool Partiton Wizard!!!, open it, u will see 16 partitions, delete them all, remember do not create new partition, just delete 16 and create single unallocated space!!!!!!!!, Now U r in 9006 mode
5. Now Extract The Firmware zip, its of 600MB but after extracting it will be of 7.8 GB
6. Open EMMC Raw Tool
7. Click on Browse ( On the Right Side Under Write Section), Now Browse for the *.Bin File U have extracted,
8. Click on Load Partition Stucture From Write Menu
9. Click On Write Full Image.
10. It will take 10-15 mins.
11. just disconnect ur phone and power it on, here's goes the magic
u have an unlocked bootloader, and old lollipop rom,
Enjoy!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Hi ! I flashed volte.img using fasboot nethod in z00ld. But no volte coming.. only baseband changed. Pls help .

how do u know if you're in 9006 or 9008 mode?

is this gonna work if the phone is booting?, my wifi is turning on but can't detect any networks. i have the files to use in qpst but i cant seem to get the phone on 9008 or 9006. i've tried pressing buttons the inserting usb it doesnt work. maybe you can help me. i just want to refurbish and reformat my emmc of the phone ze550kl. thank you

Hi!
I flashed the bin file here, my phone does not still power on.

Link Error 404
Please renew it

Back to emui 8.0 stock

I SPECIFICALLY TRIED THIS ON HONOR 9I RNE-L22 CANT GUARANTY IF IT WILL WORK ON OTHER DEVICES
DEFINITLY NOT FOR NOOBS
READ EVERY STEPS VERY CAREFULLY BEFORE PROCEEDING
PREREQUISITE -
Honor 9i RNE-L22
Huawei multi-tool
Brains
Link
Huawei Multi-tool
Setting up multitool before unbricking
- Simply install and the Open multitool.
- If asks for update then update the applicatin.
- Install driver from the right corner drop down menu
- then click on choose device code name select RNE and leave the rest
- the tick mark the EMUI 8
- go to misc tab
- click on run firmware finder
- once the firmware finder app is opened it may ask to update update it
- then once update is done click on Common base tab
- once in common base tab go to search field and type this RNE-L22C675 and press entre
- a list of firmware will be shown select the second one (RNE-L22C675CUSTC675D1B310 (8.0.0.310) 2.85gb
- click on file list you will get three links, copy each link one at a time and download the files with IDM(for faster download)
- Once download is complete, extract each zip file in seperate folders (folder one - Update, folder 2 - update_data_full_public,
folder 3 - update_full_RNE-L22_hw_in
- go to huawei multitool and go to unbrick tab,
- once in unbrick tab select LAUNCH HUAWEI UPDATE EXTRACTOR
- once the Update extractor app opens click on settings tab and unchek the option checksum header
- then go to unpack tab and select the UPDATE.APP file of the first folder, you will see alot of files press and hold cntrl button and
select only the files that i mention here SYSTEM.img, RAMDISK.img and RECOVERY_RAMDISK , then right click and select "
extract selected", now it will show a dialogue box to choose a folder (create a folder in desktop as Unbrick) select the folder .
- once extraction is done then again go to update extractor and now select the UPDATE.APP from the third folder and it will a lot
of files select only that i mention here CUST.img and right click and select "extract selected" choose the same folder that you
created in desktop as Unbrick.
- once the extraction is done go back to huawei multitool and to go unbrick tab and select specify folder and choose the folder
where you extracted those img file(that is the Unbrick folder from desktop)
- once folder selected on the right side there is a progress section it will show as all images are found.
- now connect your device in fastboot mode and click on the refresh icon beside device not connected it will recognise your device.
- now click on unbrick and the flash process will start.
- once it shows flash is cmplete disconect you device and restart.
VOILA u r back on EMUI 8.0
Important note
Once you boot up your device on emui you might find there are many things not working like Themes, Equilizer, VOLTE...
HA ha ha DONT PANIC there is a solution to that too..
-Now once your are in EMUI open settings and enable USB debugging
-now if u have hisuit in your computer uninstall that and restart your pc once,
-now open huawei multitool go to misc tab and click on "Installing HiSuit for DNS"
-it will download an older version and it will install, install and DO NOT UPDATE that.
-Once installation complete open hisuit and connect your device and your device will ask for ADB permission alow that and your device will connect
-now open firmware finder app and search the same firmware and right click on "filelist" and select copy
and click on dns update icon (cloud and sheet sign) there will a blank box right click there and select paste, and then click on register it will show as now you can proceed .. now click on "copy DNS to clipboard.
- Now open your pc network settings and change the current networks DNS with the one you copied and save.
- now come to hisuit and click on update it will show there is an update now proceed with the update.(It will take almost 40mis depending on your networks speed)
- WHILE UPDATING DO NOT DISCONNECT THE DEVICE. AND MAKE SURE THERE IS ATLEAST 60% CHARGE IS THERE IN YOUR DEVICE.
- now after updating is complete your device will restart and boot into STOCK EMUI
- disconnect your device
- restore your networks (DNS) to what was your networks default.
- now everything will work except VOLTE.
- AGAIN DONT PANIC ONE LAST STEP IS LEFT.
- go to about phone and check for update there you will get an official update sized around 580mb ,
proceed with the update.
VOILA you are in official EMUI stock rom.. EVERYTHING WORKS PERFECTLY FINE.
No bugs nothing.

Thanks, man. You are really helpful...
---------- Post added at 06:01 PM ---------- Previous post was at 06:00 PM ----------
Could you upload the Huawei multi tool in any other platform. Mega.nz is not responding.

Will this relock the bootloader?

Worked for me. I rebooted and everything is working. Even Bolte without performing those extra steps. Thanks @sknoman1
---------- Post added at 09:41 AM ---------- Previous post was at 09:40 AM ----------
Only bootloader is still unlocked and still getting warning message while booting

AnantNigam said:
Worked for me. I rebooted and everything is working. Even Bolte without performing those extra steps. Thanks @sknoman1
---------- Post added at 09:41 AM ---------- Previous post was at 09:40 AM ----------
Only bootloader is still unlocked and still getting warning message while booting
Click to expand...
Click to collapse
To lock bootloader.. go to the bootloader tab in multitool and there you can find an option as lock bootloader for that you will need the same unlock code that u used to unlock the bootloader in the first place.. follow the instructions which is given in the app.. its simple

hi , i forgot allow usb debugging option and wiped my rom and entered fastboot mode. my device is not detected. Do I have to wipe rom after allowing usb debugging and then enter into fastboot? And will there be any pop up coming after installing drivers? I dont get any pop up.
Device isn't get detected in fastboot mode. It gets detected when it is on. Can't understand.
In some blogs, Honor 7x and Honor 8 users posted that they got freezed at honor logo using this process. Why is that happening?
Why didn't we use vendor.img here?
I feel like im troubling u bro. sorry for that but u helped me like no one else did.

Praveen Jeykar said:
hi , i forgot allow usb debugging option and wiped my rom and entered fastboot mode. my device is not detected. Do I have to wipe rom after allowing usb debugging and then enter into fastboot? And will there be any pop up coming after installing drivers? I dont get any pop up.
Device isn't get detected in fastboot mode. It gets detected when it is on. Can't understand.
In some blogs, Honor 7x and Honor 8 users posted that they got freezed at honor logo using this process. Why is that happening?
Why didn't we use vendor.img here?
I feel like im troubling u bro. sorry for that but u helped me like no one else did.
Click to expand...
Click to collapse
Just follow every step from my tutorial and you won't have any problem.

How to unroot honor 9i?

sir my honor 9i not working
sknoman1 said:
I SPECIFICALLY TRIED THIS ON HONOR 9I RNE-L22 CANT GUARANTY IF IT WILL WORK ON OTHER DEVICES
DEFINITLY NOT FOR NOOBS
READ EVERY STEPS VERY CAREFULLY BEFORE PROCEEDING
PREREQUISITE -
Honor 9i RNE-L22
Huawei multi-tool
Brains
Link
Setting up multitool before unbricking
- Simply install and the Open multitool.
- If asks for update then update the applicatin.
- Install driver from the right corner drop down menu
- then click on choose device code name select RNE and leave the rest
- the tick mark the EMUI 8
- go to misc tab
- click on run firmware finder
- once the firmware finder app is opened it may ask to update update it
- then once update is done click on Common base tab
- once in common base tab go to search field and type this RNE-L22C675 and press entre
- a list of firmware will be shown select the second one (RNE-L22C675CUSTC675D1B310 (8.0.0.310) 2.85gb
- click on file list you will get three links, copy each link one at a time and download the files with IDM(for faster download)
- Once download is complete, extract each zip file in seperate folders (folder one - Update, folder 2 - update_data_full_public,
folder 3 - update_full_RNE-L22_hw_in
- go to huawei multitool and go to unbrick tab,
- once in unbrick tab select LAUNCH HUAWEI UPDATE EXTRACTOR
- once the Update extractor app opens click on settings tab and unchek the option checksum header
- then go to unpack tab and select the UPDATE.APP file of the first folder, you will see alot of files press and hold cntrl button and
select only the files that i mention here SYSTEM.img, RAMDISK.img and RECOVERY_RAMDISK , then right click and select "
extract selected", now it will show a dialogue box to choose a folder (create a folder in desktop as Unbrick) select the folder .
- once extraction is done then again go to update extractor and now select the UPDATE.APP from the third folder and it will a lot
of files select only that i mention here CUST.img and right click and select "extract selected" choose the same folder that you
created in desktop as Unbrick.
- once the extraction is done go back to huawei multitool and to go unbrick tab and select specify folder and choose the folder
where you extracted those img file(that is the Unbrick folder from desktop)
- once folder selected on the right side there is a progress section it will show as all images are found.
- now connect your device in fastboot mode and click on the refresh icon beside device not connected it will recognise your device.
- now click on unbrick and the flash process will start.
- once it shows flash is cmplete disconect you device and restart.
VOILA u r back on EMUI 8.0
Important note
Once you boot up your device on emui you might find there are many things not working like Themes, Equilizer, VOLTE...
HA ha ha DONT PANIC there is a solution to that too..
-Now once your are in EMUI open settings and enable USB debugging
-now if u have hisuit in your computer uninstall that and restart your pc once,
-now open huawei multitool go to misc tab and click on "Installing HiSuit for DNS"
-it will download an older version and it will install, install and DO NOT UPDATE that.
-Once installation complete open hisuit and connect your device and your device will ask for ADB permission alow that and your device will connect
-now open firmware finder app and search the same firmware and right click on "filelist" and select copy
and click on dns update icon (cloud and sheet sign) there will a blank box right click there and select paste, and then click on register it will show as now you can proceed .. now click on "copy DNS to clipboard.
- Now open your pc network settings and change the current networks DNS with the one you copied and save.
- now come to hisuit and click on update it will show there is an update now proceed with the update.(It will take almost 40mis depending on your networks speed)
- WHILE UPDATING DO NOT DISCONNECT THE DEVICE. AND MAKE SURE THERE IS ATLEAST 60% CHARGE IS THERE IN YOUR DEVICE.
- now after updating is complete your device will restart and boot into STOCK EMUI
- disconnect your device
- restore your networks (DNS) to what was your networks default.
- now everything will work except VOLTE.
- AGAIN DONT PANIC ONE LAST STEP IS LEFT.
- go to about phone and check for update there you will get an official update sized around 580mb ,
proceed with the update.
VOILA you are in official EMUI stock rom.. EVERYTHING WORKS PERFECTLY FINE.
No bugs nothing.
Click to expand...
Click to collapse
my phone is showing no os installed and cnt be able to open please help me sir and please send me your contact number

yogeshyadavv143 said:
my phone is showing no os installed and cnt be able to open please help me sir and please send me your contact number
Click to expand...
Click to collapse
did you follow the exact procedure?
if you have missed a single part that give you the exact message as no os installed

Hi guys, really sorry to ask, but how do I install Multi Tool on Mac OS? Thanks in advance!

This will work on Nova 2i? As this is same as Honor 9i.

[UNBRICK] [RECOVER IMEI] Unbrick hardbricked max pro m1 and recover IMEI [QFIL]

I am not responsible for bricked devices and dead SD cards. YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you.
Click to expand...
Click to collapse
This thread is for those who's phone is hard bricked ( not even going to fast boot or recovery ). here we will explain how you can revive it.
things you need :-
1. QPST Tool - QPST Tool
2. QFIL Rom - ZB601KL/ZB602KL Download from HERE
3. Qcom drivers - Qcom drivers
First of all install QPST tool and drivers and extract QFIL rom after that go to QPST installed folder in my case that was C:\Program Files\Qualcomm\QPST\bin
open QFIL.exe
In Build type Select Flat Build
in Select Programmer go to that folder where u extracted Qfil rom.zip and select prog_emmc_ufs_firehose_Sdm660_ddr.elf
Now Click on Load xml and select rawprogram_unsparse_ww.xml in next window select patch0.xml
.
SCREENSHOTS
Click to expand...
Click to collapse
now Connect your device now if you see Something else like Qualcomm HS-USB Diagnostics in place of no port Selected Click DownLoad else check drivers.
it will take some time after process completes you can boot your phone and this rom is not meant for daily uses so flash any fastboot rom now.
Backing Up IMEI (QCN) ?
things you need :-
1. QPST Tool - QPST Tool
2. Qcom drivers - Qcom drivers
Steps :
1. You should be on rooted stock rom. and Qcom drivers & QPST Tool installed on your pc.
2. Add ro.build.selinux=0 and sys.usb.config=diag,adb to build.prop now reboot.
3. connect your phone to pc and open Qfil select tools > QCN Backup Restore from menu bar. Click Backup in next window.
Done..
Note : if you see No Port Available in QFIL check drivers or step 2.
Restoring IMEI (QCN)
things you need :-
1. QPST Tool - QPST Tool
2. Qcom drivers - Qcom drivers
Steps :
1. You should be on rooted stock rom. and Qcom drivers & QPST Tool installed on your pc.
2. Add ro.build.selinux=0 and sys.usb.config=diag,adb to build.prop now reboot.
3. connect your phone to pc and open Qfil select tools > QCN Backup Restore from menu bar.
4. Choose your QCN file and Click Restore in next window.
Done..
Note : if you see No Port Available in QFIL check drivers or step 2.
Editing QCN File :
things you need :-
IMEI to HEX Converter - https://drive.google.com/file/d/1spyz5bpeSY1NBu1IZGQlLZersARG5EKR/view?usp=sharing
HEx Editer - download ultra Edit (Do Google search)
1. Open QCN file with ultra Edit click find and search for old imei(hex use hex converter).
2. replace with new hex do for both imei and save.
done now you can restore.
Credits :
@Saktis_STi
- Akshat
@SagarMakhar
- Jakwarlord
And All who helped

will this allow me for ota updates??

Is there any guide to restore serial number ?

@ yourkk Could you please explain this "this rom is not meant for daily uses so flash any fastboot rom now." Do you mean that after your steps, mobile should be booting to fastboot and then stock firmware can be flashed?

Jaheen said:
@ yourkk Could you please explain this "this rom is not meant for daily uses so flash any fastboot rom now." Do you mean that after your steps, mobile should be booting to fastboot and then stock firmware can be flashed?
Click to expand...
Click to collapse
It will install QFIL Rom (Unofficial Stock ROM)
So flash Official STOCK or any desired Rom :fingers-crossed:

How to restore serial number ???

benchmarker said:
It will install QFIL Rom (Unofficial Stock ROM)
So flash Official STOCK or any desired Rom :fingers-crossed:
Click to expand...
Click to collapse
Thank you!

jide1 said:
How to restore serial number ???
Click to expand...
Click to collapse
imei is serial number

AkashAlien said:
imei is serial number
Click to expand...
Click to collapse
You must be an [emoji2959]!

jide1 said:
How to restore serial number ???
Click to expand...
Click to collapse
Bazz 27:
http://androroot.com/2015/05/how-to-solve-invalid-imei-and-seria.html try this

yourkk said:
This thread is for those who's phone is hard bricked ( not even going to fast boot or recovery ). here we will explain how you can revive it.
things you need :-
1. QPST Tool - QPST Tool
2. QFIL Rom - ZB601KL/ZB602KL Download from HERE
3. Qcom drivers - Qcom drivers
First of all install QPST tool and drivers and extract QFIL rom after that go to QPST installed folder in my case that was C:\Program Files\Qualcomm\QPST\bin
open QFIL.exe
In Build type Select Flat Build
in Select Programmer go to that folder where u extracted Qfil rom.zip and select prog_emmc_ufs_firehose_Sdm660_ddr.elf
Now Click on Load xml and select rawprogram_unsparse_ww.xml in next window select patch0.xml
.
now Connect your device now if you see Something else like Qualcomm HS-USB Diagnostics in place of no port Selected Click DownLoad else check drivers.
it will take some time after process completes you can boot your phone and this rom is not meant for daily uses so flash any fastboot rom now.
Backing Up IMEI (QCN) ?
things you need :-
1. QPST Tool - QPST Tool
2. Qcom drivers - Qcom drivers
Steps :
1. You should be on rooted stock rom. and Qcom drivers & QPST Tool installed on your pc.
2. Add ro.build.selinux=0 and sys.usb.config=diag,adb to build.prop now reboot.
3. connect your phone to pc and open Qfil select tools > QCN Backup Restore from menu bar. Click Backup in next window.
Done..
Note : if you see No Port Available in QFIL check drivers or step 2.
Restoring IMEI (QCN)
things you need :-
1. QPST Tool - QPST Tool
2. Qcom drivers - Qcom drivers
Steps :
1. You should be on rooted stock rom. and Qcom drivers & QPST Tool installed on your pc.
2. Add ro.build.selinux=0 and sys.usb.config=diag,adb to build.prop now reboot.
3. connect your phone to pc and open Qfil select tools > QCN Backup Restore from menu bar.
4. Choose your QCN file and Click Restore in next window.
Done..
Note : if you see No Port Available in QFIL check drivers or step 2.
Editing QCN File :
things you need :-
IMEI to HEX Converter - https://drive.google.com/file/d/1spyz5bpeSY1NBu1IZGQlLZersARG5EKR/view?usp=sharing
HEx Editer - download ultra Edit (Do Google search)
1. Open QCN file with ultra Edit click find and search for old imei(hex use hex converter).
2. replace with new hex do for both imei and save.
done now you can restore.
Credits :
@Saktis_STi
- Akshat
@SagarMakhar
- Jakwarlord
And All who helped
Click to expand...
Click to collapse
Guys, the October update bricked my phone, so I used the Fastboot Firmware to restore my phone (WW_ZB601KL(ZB602KL)_15.2016.1805.316_20180706), but now my imei is gone ? ! What do I do ? Please help me out !

It just doesnt work....
followed the steps...
it gives an error.... sahara failed...
searched all over the internet but no fix.....
please help me..
(I was trying to port a rom but flashed it with wrong updater script....)

please help me . i did everything. but in qfil it says error
cannot switch to emergency download

Use miracle box
ashutoshashukla said:
please help me . i did everything. but in qfil it says error
cannot switch to emergency download
Click to expand...
Click to collapse
Try miracle box....google it and download it..
Open miracle box
Goto qualcomm->flash/write-> (Tick EDL mode....)
here you will get an option to load your rom file,programmer and patch.xml...

I have flashed the qphil ROM using QPST tool
And restored my IMEI using QCN file thanks for this post.
But after I have flashed pie ROM my first sim slot only working as 2g and data not working
but 2nd sim slot working 4g and data good.
I have tried flashing stock ROM also and currently am in LR ROM.
#1st sim no data and no 4g but call and message works
Any help please?

psgbharathi said:
I have flashed the qphil ROM using QPST tool
And restored my IMEI using QCN file thanks for this post.
But after I have flashed pie ROM my first sim slot only working as 2g and data not working
but 2nd sim slot working 4g and data good.
I have tried flashing stock ROM also and currently am in LR ROM.
#1st sim no data and no 4g but call and message works
Any help please?
Click to expand...
Click to collapse
Sorry if I'm not addressing your question, but where did you get the QCN file? Also, can you tell me how to restore serial number?

jide1 said:
Sorry if I'm not addressing your question, but where did you get the QCN file? Also, can you tell me how to restore serial number?
Click to expand...
Click to collapse
Search this in Google 'world first max pro m1 qcn file'
Forum.gsm website u can find the dummy file
Can you give any suggestion to my problem?
IMEI restored but no data in slot 1
Do I need to fastboot stock rom

psgbharathi said:
Search this in Google 'world first max pro m1 qcn file'
Forum.gsm website u can find the dummy file
Can you give any suggestion to my problem?
IMEI restored but no data in slot 1
Do I need to fastboot stock rom
Click to expand...
Click to collapse
Try using stock rom and see.

jide1 said:
Try using stock rom and see.
Click to expand...
Click to collapse
Will do the fast boot stock ROM and tell you
Thanks

is anyone here have do this way? and whats the results? can i get the QCN File, please..

[GUIDE] How to return to Stock/Flash Images with QFIL

Here is a step by step guide on how to flash the stock rom with QFIL and by extension any image.
Download and install the Qualcomm drivers from here
Download either of the firmware from here
Download the support files (Firehose/rawprogram0.xml/patch0.xml) here
Extract the firmware and support files to the same folder so you can easily access them like your desktop
Download and install QPST from here
Open the QFIL application (Find it in your start menu)
In the "Select Build Type" field select Flat Build
In the "Select Programmer" field navigate to the folder you extracted the firmware and support files to and select the prog_emmc_firehose_8909.mbn file
Select the "Load XML" button and navigate to the folder you extracted the firmware and support files to and select the rawprogram0.xml and then the patch0.xml when prompted.
Plug in your tablet
Run the following adb command "adb reboot edl" (Now the screen should be blank but the led light should be red)
If the text at the top of the QFIL application says "No Port Available" click the "Select Port..." option and pick your device. If your device isn't showing up there you didn't install the drivers properly.
Click the Download Button to begin flashing your device
So the above explains how to flash everything if you want to flash individual partitions you can edit your rawprogram0.xml to only include the ones you want. (patch0.xml stays the same) I have linked below 2 examples, one of them flashes just a boot.img and one that just flashes the recovery.img. But you aren't limited to those.
Recovery
Boot

Mine just in case

Awesome, thanks for this post! it will really help us in upcoming projects!

Managed to revive my phone using the B12 files but it crashes after completing system.img, I think the problem is userdata.img, my phone boots but I lost the imei and I don't know how to get it back, I'm still trying.

ZTE 971 not recognized by either QPST or QFIL
Thanks for all the detailed instructions. But my ZTE 971 is not visible to either qpst or qfil eventhough the phone shows in windows 8.1. In the Developer Options menu, I noticed Select USB Configuration, RNDIS (USB ethernet) option cannot be enabled. I wonder if this has anything to do with it. OEM unlocking, USB debbugging are already selected. Any suggestions, please? Thanks.
ps. I live in Turkey. I got this phone last year from AT&T and have unlocked the sim.

My PC is not detecting my ZTE MAVEN 3
I have installed all drives but still facing the issue. I am using it on Windows 10.

I flashed the B13 (ZPST tool shows my device as B13) with the QFIL like your guide says and it says all completed successfully and finishes, but now my phone went from only being able to boot EDL + FTM + Recovery, to now booting directly to EDL mode, which obviously means this guide completely screwed up my phone... Thanks.

Mega says that link for the driver is invalid, but the driver is included in your QPST download anyway.

000Nick said:
I flashed the B13 (ZPST tool shows my device as B13) with the QFIL like your guide says and it says all completed successfully and finishes, but now my phone went from only being able to boot EDL + FTM + Recovery, to now booting directly to EDL mode, which obviously means this guide completely screwed up my phone... Thanks.
Click to expand...
Click to collapse
solucionaste hermano
Mod edit:
you solved brother
Click to expand...
Click to collapse

it says qhsusb_bulk when I connect the the software is not working in the mobile and it is stuck at bootloader screen but I used the press both buttons to go to edl mode method and it said in the device manager a device connected with name : qhsusb_bulk
help pls

Hello All.
I am not able to get the following files
rawprogram.xml and patch.xml for LG G8xPlease help me to get this files ASAP as i have hard bricked the mobile, all partitions deleted

Database Develop

welcome