Hello I install TWRP to my Mate S without root,but now I can't update my phone and I can't restore the backup I get. How I go back to the original recovery. The phone is with UL 00 rom.
takisspanos said:
Hello I install TWRP to my Mate S without root,but now I can't update my phone and I can't restore the backup I get. How I go back to the original recovery. The phone is with UL 00 rom.
Click to expand...
Click to collapse
You will need to flash the stock recovery in the same way that you flashed the TWRP recovery. So the way I would do it is connect phone to laptop..then use command
"adb reboot bootloader"
Then when your phone is in bootloader mode and with the stock recovery in the same folder as where fastboot and adb are use the command
"fastboot flash recovery recovery.img"
And replace recovery. img with the name of the recovery u want to flash.
Then reboot and you should be back to stock
I am on L09 but if you want I can upload my recovery
Edit: I found a stock recovery file in a thread, this is the one I used on my L09 - READ THE COMPATABILITY WARNING BEFORE FLASHING AS YOUR OWN RISK
http://forum.xda-developers.com/mate-s/help/stock-rom-t3230051
Thank you, but your recovery is the same with mine UL00 ?
takisspanos said:
Thank you, but your recovery is the same with mine UL00 ?
Click to expand...
Click to collapse
I dont know the answer to that. I updated my post above with a link to L09 recovery
Alternative is you need original stock rom to extract recovery.img from
---------- Post added at 09:29 AM ---------- Previous post was at 09:18 AM ----------
takisspanos said:
Thank you, but your recovery is the same with mine UL00 ?
Click to expand...
Click to collapse
I've just figured out a way to get the recovery for you, if you give me about 1 hour I will extract the recovery.img from UL00 Stock B120 (Lollipop) firmware and upload it
I have the original stock rom from here http://www.needrom.com/download/ascend-mate-s-crr-ul00/ .Now I have to found how extract the recovery.img
Thank you very much.
takisspanos said:
Thank you very much.
Click to expand...
Click to collapse
I'm just downloading the B103 stock ROM.
If you want to try you can see how here
http://forum.xda-developers.com/showthread.php?t=2433454
https://www.youtube.com/watch?v=Z3rw78gAl3k
Make sure the ROM you have is the full ROM and not the update because the update might not contain recovery.img
The B103 is CRR-UL00 . Because i saw CRR-UL00-C00B104-unicom.zip. It is the firt at needrom.com
takisspanos said:
The B103 is CRR-UL00 . Because i saw CRR-UL00-C00B104-unicom.zip. It is the firt at needrom.com
Click to expand...
Click to collapse
I'm struggling to extract the recovery.img - I keep getting a CRC Error.
Is it working for you?
If I install UL00 B144 the latest I found is it posible to return on original recovery ? But I don't know how to install , it is posible with TWRP.
takisspanos said:
If I install UL00 B144 the latest I found is it posible to return on original recovery ? But I don't know how to install , it is posible with TWRP.
Click to expand...
Click to collapse
I dont think you can install without the stock recovery...it doesnt work with TWRP
Hello my friend brumgav I download-- CRR-UL00-C00B104-unicom --. I use the- -HuaweiUpdateExtractor_0.9.9.3-- I found Recovery.img. I have to install it with -Minimal ADB and Fastboot- and I am OK ? I used the -Minimal ADB and Fastboot- for installing the TWRP.
extract the recovery.img from your current update.app. then flash the img-file like you flashed the twrp recovery.
OK I did it
1. I use the- -HuaweiUpdateExtractor_0.9.9.3
2.I found Recovery.img and I flash like the TWRP and everything is OK.
Thanks everybody.
takisspanos said:
OK I did it
1. I use the- -HuaweiUpdateExtractor_0.9.9.3
2.I found Recovery.img and I flash like the TWRP and everything is OK.
Thanks everybody.
Click to expand...
Click to collapse
Well done - Glad it worked
OK I did it
1. I use the- -HuaweiUpdateExtractor_0.9.9.3
2.I found Recovery.img and I flash like the TWRP and everything is OK.
Thanks everybody.
.I have TWRP recovery and phone is not booting....In fastboot mode how to flash stock recovery over FRP lock...???
jigs88 said:
.I have TWRP recovery and phone is not booting....In fastboot mode how to flash stock recovery over FRP lock...???
Click to expand...
Click to collapse
read other threads. FRP Lock => you can´t do sh**
Tuerkay said:
read other threads. FRP Lock => you can´t do sh**
Click to expand...
Click to collapse
Is it possible to unlock FRP via TWRP or adb or bypass
jigs88 said:
Is it possible to unlock FRP via TWRP or adb or bypass
Click to expand...
Click to collapse
you need the working OEM-Unlock option in your settings or an TWRP backup without FRP-lock.
even with TWRP recovery you can´t flash anything with adb/fastboot while your device is FRP Locked.
Related
Hry guys. Since miui is not for me. How do i revert back to the stock recovery so i can use the updates? Cheers
deepsnoozer said:
Hry guys. Since miui is not for me. How do i revert back to the stock recovery so i can use the updates? Cheers
Click to expand...
Click to collapse
Hi,
You have to flash stock recovery via ADB. Only image 1 not 2. Than you can easy flash a stock rom via dload Method.
All you need is here:
http://forum.xda-developers.com/asc...26-to-b133-t2888976/post55708921#post55708921
Sent from my HUAWEI P7-L10 using XDA Free mobile app
87insane said:
Hi,
You have to flash stock recovery via ADB. Only image 1 not 2. Than you can easy flash a stock rom via dload Method.
All you need is here:
http://forum.xda-developers.com/asc...26-to-b133-t2888976/post55708921#post55708921
Sent from my HUAWEI P7-L10 using XDA Free mobile app
Click to expand...
Click to collapse
The easy way is to flash with flashify! Download it from playstore, put your stock recovery on sd card- start flashify and flash recovery.
Superwitschi said:
The easy way is to flash with flashify! Download it from playstore, put your stock recovery on sd card- start flashify and flash recovery.
Click to expand...
Click to collapse
Only flash recovery.img with flashify?
Not flash recovery2.img?
yes only the recovery.img!!!!
Superwitschi said:
yes only the recovery.img!!!!
Click to expand...
Click to collapse
Ok thanks...
Dear all. Iam back to stock thabk you so much. Oh btw i used abd
deepsnoozer said:
Dear all. Iam back to stock thabk you so much. Oh btw i used abd
Click to expand...
Click to collapse
Mate, please describe how you did it with ADB in detailed
radostorm said:
Mate, please describe how you did it with ADB in detailed
Click to expand...
Click to collapse
Standard doing....
Sent from my HUAWEI P7-L10 using XDA Free mobile app
radostorm said:
Mate, please describe how you did it with ADB in detailed
Click to expand...
Click to collapse
The same way you have flashed TWRP.
DJ BlackEagle said:
The same way you have flashed TWRP.
Click to expand...
Click to collapse
Hi,
I need help... I'm trying to go back to stock recovery & firmware, I have already tried everything and I'm absolutely fustrated:crying::crying::crying:
1.- I had TWRP recovery and MIUI, the phone (ASCEND P7-L10) is rooted
2.- After downloading flashify and the stock recovery, I have installed the stock recovery, everything OK.
3.- Rebbot into recovery and when I try to wipe data and/or cache it says:
data wipe completed (or cache wipe completed)
huawei cust fail
If I try to install any ROM B120, B126, B133, B135... I always get the same error, "cust fail"
If I reboot the phone still has MIUI... but I need to restore to factory recovery/firmware...
Help needed, I'm going to hit the roof...
thanks in advance!
Put your original firmware on dload in sd card, flash original recovery with fastboot or flashify, shut down your phone. Now press power volume- and volume+ ! This will install the original firmware.
siasegos said:
...
3.- Rebbot into recovery and when I try to wipe data and/or cache it says:
data wipe completed (or cache wipe completed)
huawei cust fail
...
Click to expand...
Click to collapse
Read my tutorial but additionaly in point 4. you must flashing also cust.img by Fastboot (make command: Fastboot flash cust cust.img) It always working.
Ziolek67 said:
Read my tutorial but additionaly in point 4. you must flashing also cust.img by Fastboot (make command: Fastboot flash cust cust.img) It always working.
Click to expand...
Click to collapse
Before reading your post I've been doing some test and after flashing boot.img sotck firmware has been installed, but I still have cust fail error.
Now I have read your tuto but where I can download cust .img??
Many thanks for your help
siasegos said:
Before reading your post I've been doing some test and after flashing boot.img sotck firmware has been installed, but I still have cust fail error.
Now I have read your tuto but where I can download cust .img??
Many thanks for your help
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2920167
Thanks, already flashed again recovery , boot and cust
Now forcing update vol+ vol- power
we'll see. Anyway, thanks a lot!
siasegos said:
Now I have read your tuto but where I can download cust .img??
Many thanks for your help
Click to expand...
Click to collapse
Use only original stock cust.img extracted from stock ROM. I always do it in this order:
1. Download mode and flashing stock recovery
2. Recovery mode and wipe (both option)
3. Download mode and flashing cust.img
4. Recovery mode and wipe (both option)
5. If still error go download mode and flash:
cust.img, cache.img, userdata.img, system.img
6. Recovery mode and wipe (both option)
I had many times this error while reverting my B135 after MIUI ROM.
Ziolek67 said:
Use only original stock cust.img extracted from stock ROM. I always do it in this order:
1. Download mode and flashing stock recovery
2. Recovery mode and wipe (both option)
3. Download mode and flashing cust.img
4. Recovery mode and wipe (both option)
5. If still error go download mode and flash:
cust.img, cache.img, userdata.img, system.img
6. Recovery mode and wipe (both option) .
Click to expand...
Click to collapse
Well, after flashing again recovery, boot, cust and forcing an update... I get the same fuc**** error, mm... As you have told me, I guess I do not have the right files for my Vodafone Spain P7-L10
I'm going to look for the right firmware, thanks a lot!!!
==== SEVERAL ATTEMPS LATER AND SOME HOURS LATER... SOLVED!!! ====
I've made svarious attemps with diferent ROMs, B126 and B121, while I was downloading original stock ROM from Huawei.
All of these attemps have failed, even flashing cache, userdata and system
But after downloading original stock rom, as soon as I have flashed cust everything started to work perfectly, wipes... firmware...
So, THAAAAANKS A LOOOOOOOT!
Superwitschi said:
Put your original firmware on dload in sd card, flash original recovery with fastboot or flashify, shut down your phone. Now press power volume- and volume+ ! This will install the original firmware.
Click to expand...
Click to collapse
hi i have the same problem, if i put my 133 d load in my sd card, the phone go however in twrp...
there is a way to install d load or a firm stock from twrp?
I did it!
I've finally did it!
Huawei has released an official downgrade ROM (B603) here (russian site):
http://download-c.huawei.com/download/downloadCenter?downloadId=38601&version=66144&siteCode=ru
You'll also need this official EMUI 3.0 recovery image:
https://mega.co.nz/#!ZZ9QxIiL!Cn4mV2ZG2zzFc956CoWQh4BnBQqyK4rClghlY8CoXQk
As well as fastboot/ADB (platform tools) files here:
https://www.androidfilehost.com/?fid=9390355257214632011
Now here's how you do it.
Copy the dload folder (found in ROM) to the root of your SD Card
Now turn off your phone
While off press and hold Vol Down & Power Key, when screen turns on release Power Key, but keep holding the Vol Down key until you see a white screen (fastboot mode)
Now decompess files from platform tools to a new folder called ADB on your desktop for example
Hold down Shift and right click on ADB folder on your Desktop and choose "run command windows here", a little black window should pop up
Now type:
fastboot devices - this is to check if your phone is correctly detected (if not, then drivers are needed. Just install HiSuite)
fastboot flash recovery stockEMUI3.0RECOVERY.img
fastboot reboot
Your phone will now boot into your current OS. Go to Settings>Updates>Local Update
This will install the downgrade ROM from russian Huawei site (B603)
After this is installed your phone will boot into your current OS again. This time delete UPDATE.APP from dload folder and put your stock firmware in there.
Now repeat the process Settings>Update>Local Update
This time it will finally install that stock KitKat with EMUI 2.3 OMG !!! Finally !!!
God i hope i'll never have to do this again
Hello all,
I've rooted my P8Lite L21 using the custom recovery method, flashed the supersu.zip, then restored the original recovery.
Yesterday I had an OTA and now phone reboot once during system boot, and at the second time it hangs during boot.
What can I do to recover this? I have stock recovery, and when I try to VOLDOWN+POWER it never goes to fastboot. (last time I had to use adb reboot-bootloader but now I can't reach system\adb..)
Can you help?
Thanks, cheers,
pHk
Phk said:
Hello all,
I've rooted my P8Lite L21 using the custom recovery method, flashed the supersu.zip, then restored the original recovery.
Yesterday I had an OTA and now phone reboot once during system boot, and at the second time it hangs during boot.
What can I do to recover this? I have stock recovery, and when I try to VOLDOWN+POWER it never goes to fastboot. (last time I had to use adb reboot-bootloader but now I can't reach system\adb..)
Can you help?
Thanks, cheers,
pHk
Click to expand...
Click to collapse
Hello,
You can boot to fastboot with this method:
Connect phone with PC then power off
Now push two buttons VOLDOWN+POWER+MicroUSB now you can install any stock ROM with fastboot commands and suitable *.img(boot.img, cust.img, system.img)
P.S
What OTA(number) arrive to you?
sokkoban said:
You can boot to fastboot with this method:
Connect phone with PC then power off
Now push two buttons VOLDOWN+POWER
Click to expand...
Click to collapse
Worked like a charm Thanks a lot! I don't know the OTA number.. Still can't get into system :|
I'll try flashing TWRP from here and then i don't know which rom to use.. I'd like CM12 but i'm not sure its supported.
Can you suggest any stable ROM ?
Thanks
Phk said:
Worked like a charm Thanks a lot! I don't know the OTA number.. Still can't get into system :|
I'll try flashing TWRP from here and then i don't know which rom to use.. I'd like CM12 but i'm not sure its supported.
Can you suggest any stable ROM ?
Thanks
Click to expand...
Click to collapse
First you try to remember what is your last ROM number and your region. Or you can install the last beta on android 5.1.1(B010) need unlocked bootloader
Here all official firmware for device ALE-L21
http://huaweip8lite.blogspot.bg/2016/01/huawei-p8-lieale-l21-official-firmware.html
sokkoban said:
First you try to remember what is your last ROM number and your region. Or you can install the last beta on android 5.1.1(B010) need unlocked bootloader
Here all official firmware for device ALE-L21
http://huaweip8lite.blogspot.bg/2016/01/huawei-p8-lieale-l21-official-firmware.html
Click to expand...
Click to collapse
It's Portuguese\Europe, Single SIM.
I'm downloading "Huawei P8 Lite ALE-L21 V100R001C432B171 (Europe)". Is this flashable from fastboot? Yes, i'm unlocked. Does it need the hiSuite or fastboot.exe will suffice?
Thanks Sokkoban, you're being of great help and I'm thanking all your posts
Phk said:
It's Portuguese\Europe, Single SIM.
I'm downloading "Huawei P8 Lite ALE-L21 V100R001C432B171 (Europe)". Is this flashable from fastboot? Yes, i'm unlocked. Does it need the hiSuite or fastboot.exe will suffice?
Thanks Sokkoban, you're being of great help and I'm thanking all your posts
Click to expand...
Click to collapse
Wait my friend this is single sim ROM
I must download dual sim if you have dual sim device
Yes I'm not shure but if you want install B170 you need first downgrade to B052 then you can install via OTA best and last ROM for you country
sokkoban said:
Wait my friend this is single sim ROM
I must download dual sim if you have dual sim device
Yes I'm not shure but if you want install B170 you need first downgrade to B052 then you can install via OTA best and last ROM for you country
Click to expand...
Click to collapse
Yes, I know this is single SIM. But, why do you say that I need to downgrade to B052 and then OTA? Can't i flash the B170 directly?
The other question i had is, how to flash this. Hisuite or fastboot.exe?
Thanks
Phk said:
Yes, I know this is single SIM. But, why do you say that I need to downgrade to B052 and then OTA? Can't i flash the B170 directly?
The other question i had is, how to flash this. Hisuite or fastboot.exe?
Thanks
Click to expand...
Click to collapse
Because after downgrade you can install any firmware via OTA! (ROM B052 is from the box!)
I write guide how to unbrick ALE-L21 use google translator, download ROM and run file FLASH-ALL.bat http://huaweip8lite.blogspot.bg/2016/01/tutorialhow-to-unbrick-huawei-p8-lite.html
sokkoban said:
Because after downgrade you can install any firmware via OTA! (ROM B052 is from the box!)
I write guide how to unbrick ALE-L21 use google translator, download ROM and run file FLASH-ALL.bat http://huaweip8lite.blogspot.bg/2016/01/tutorialhow-to-unbrick-huawei-p8-lite.html
Click to expand...
Click to collapse
If you don't see any problem, I will try to flash B170 directly, since my bootloader is already unlocked. What do you think?
About the link you sent, the site appears in English, but then it changes to russian? I cannot get it back to EN.
Thanks
How to root samsung galaxy y2 smg130h?
halim4 said:
How to root samsung galaxy y2 smg130h?
Click to expand...
Click to collapse
This was actually funny. :good:
Phk said:
If you don't see any problem, I will try to flash B170 directly, since my bootloader is already unlocked. What do you think?
About the link you sent, the site appears in English, but then it changes to russian? I cannot get it back to EN.
Thanks
Click to expand...
Click to collapse
OK
Try this. Use Huawei update extractor in forum xda have link to it. Open the UPDATE.APP and extract the following files: Recovery.img, Boot.img, Cust.img, System.img
Then use fastboot commands to flash B171 ROM
I wish you success!
Regards
sokoban
Hi there,
I have a similar problem: bootloop!
I'm comming from B170 and installed 7 HD 1.2 ROM and got some errors, I thougt it would be an good to go the long way to B008 or better B010. After so searching I found: http://forum.xda-developers.com/showpost.php?p=64483642&postcount=43
- did not step 1 an under-pressed flashing recovery in step 2 and 3, thought I could yet use TWRP.
Obviously, that was the mistake.
At step 4 I recognized that I have to do step 1 to go on.
that worked an I copied the update.zip to internal card, initialised the update.
Not sure it got to 100% but think so.
Result bootloop, can't get to recovery, only fastboot
Tried to flash every thing: B052, B170, and 136a, even the boot.img and recovery.img of B010 and B008
no errors but still bootloop.
PLEASE HELP!!
is there a full version of B080 somewhere to flash by fastboot? or any options to flash the update.zip of B080 again?
All other proposals are welcome!
Rocketmaster said:
Hi there,
I have a similar problem: bootloop!
I'm comming from B170 and installed 7 HD 1.2 ROM and got some errors, I thougt it would be an good to go the long way to B008 or better B010. After so searching I found: http://forum.xda-developers.com/showpost.php?p=64483642&postcount=43
- did not step 1 an under-pressed flashing recovery in step 2 and 3, thought I could yet use TWRP.
Obviously, that was the mistake.
At step 4 I recognized that I have to do step 1 to go on.
that worked an I copied the update.zip to internal card, initialised the update.
Not sure it got to 100% but think so.
Result bootloop, can't get to recovery, only fastboot
Tried to flash every thing: B052, B170, and 136a, even the boot.img and recovery.img of B010 and B008
no errors but still bootloop.
PLEASE HELP!!
is there a full version of B080 somewhere to flash by fastboot? or any options to flash the update.zip of B080 again?
All other proposals are welcome!
Click to expand...
Click to collapse
First 7 HD 1.2 ROM work only over the B010!!!
Second in this archive have the instructions to install Beta B008 why you not did everything described in the instructions?
Third when install stock firmware RECOVERY must be original not TWRP!!!
Now you must install stok recovery, make hard reset then install B052
After that you can install every stock firmware for your region! or follow the instruction to install B008=>B010=>7 HD 1.2 ROM
Regards
sokkoban said:
First 7 HD 1.2 ROM work only over the B010!!!
Second in this archive have the instructions to install Beta B008 why you not did everything described in the instructions?
Third when install stock firmware RECOVERY must be original not TWRP!!!
Now you must install stok recovery, make hard reset then install B052
After that you can install every stock firmware for your region! or follow the instruction to install B008=>B010=>7 HD 1.2 ROM
Regards
Click to expand...
Click to collapse
I flashed Stock and restarted and flashed B052. What do you mean with hard reset? I not comming in any menu. Only fastboot works.
Still bootloop
Which method use you to flash B052?
sokkoban said:
Which method use you to flash B052?
Click to expand...
Click to collapse
fastboot
Hm, this is very strange!
What device do you have? and which region use?
adb reboot recovery --- says: error: device '(null)' not found
if I try with serialnumber
adb -s W3D7XXXXXXXX reboot recovery ---- says error: device 'W3D7XXXXXXXX' not found
but ---- fastboot devices ----says at the same time: W3D7XXXXXXXX
---------- Post added at 09:57 AM ---------- Previous post was at 09:54 AM ----------
ALE-L21 Germany
So B170 worked in the first place
Try this method and ROM
May be you must use google translator because tutorial is for Bulgarian people
http://huaweip8lite.blogspot.bg/2016/01/tutorialhow-to-unbrick-huawei-p8-lite.html
Hey,
I accidentally bricked my Honor 5c NEM-L51 Nougat Emui 5.0, by trying to flash twrp to boot.
Now i just can get into erecovery, which doesn't help or in fastboot or try to install a new image via dload, which doesn't help either.
Any help how i can fix this?
LordImperator said:
Hey,
I accidentally bricked my Honor 5c NEM-L51 Nougat Emui 5.0, by trying to flash twrp to boot.
Now i just can get into erecovery, which doesn't help or in fastboot or try to install a new image via dload, which doesn't help either.
Any help how i can fix this?
Click to expand...
Click to collapse
You flashed TWRP as boot.img?
i flashed an twrp.img on boot :/
LordImperator said:
i flashed an twrp.img on boot :/
Click to expand...
Click to collapse
Why did you do that?
itisiryan said:
Why did you do that?
Click to expand...
Click to collapse
Like I said accidentally, i tried to install twrp as a custom recovery an tapped on flash on boot instead of recovery :/
LordImperator said:
Like I said accidentally, i tried to install twrp as a custom recovery an tapped on flash on boot instead of recovery :/
Click to expand...
Click to collapse
Didbyou try flashing boot.IMG from stock firmware and to the boot partition??
LordImperator said:
Like I said accidentally, i tried to install twrp as a custom recovery an tapped on flash on boot instead of recovery :/
Click to expand...
Click to collapse
Just reflash your stock kernel.
itisiryan said:
Just reflash your stock kernel.
Click to expand...
Click to collapse
Where can i find one for my verison?
LordImperator said:
Where can i find one for my verison?
Click to expand...
Click to collapse
Download whole firmware and extract only boot.IMG and flash it like you flash recovery in boot partition.
hassanjavaid8181 said:
Download whole firmware and extract only boot.IMG and flash it like you flash recovery in boot partition.
Click to expand...
Click to collapse
I tried, that out with that firmware: http://www.carbontesla.com/2017/05/download-huawei-honor-5c-b355-nougat-update-europe-beta/,
but it didn't worked, got into an endless loop in honor booting screen, any other firmware i can download?
LordImperator said:
I tried, that out with that firmware: http://www.carbontesla.com/2017/05/download-huawei-honor-5c-b355-nougat-update-europe-beta/,
but it didn't worked, got into an endless loop in honor booting screen, any other firmware i can download?
Click to expand...
Click to collapse
which firmware number you were on before the issue?
hassanjavaid8181 said:
which firmware number you were on before the issue?
Click to expand...
Click to collapse
I get it to boot with a custom kernel [Elite Kernel v10.1], but not quite stable, the Build-Number showed in Setting there is the NEM-L51C432B355, poorly i don't know anymore, if it is the same as before.
LordImperator said:
I get it to boot with a custom kernel [Elite Kernel v10.1], but not quite stable, the Build-Number showed in Setting there is the NEM-L51C432B355, poorly i don't know anymore, if it is the same as before.
Click to expand...
Click to collapse
You have changed only kernel??not the ROM right??
---------- Post added at 05:10 PM ---------- Previous post was at 05:09 PM ----------
LordImperator said:
I tried, that out with that firmware: http://www.carbontesla.com/2017/05/download-huawei-honor-5c-b355-nougat-update-europe-beta/,
but it didn't worked, got into an endless loop in honor booting screen, any other firmware i can download?
Click to expand...
Click to collapse
You need a stock recovery to flash stock firmware...
I overflashed only the kernel, so the phone didn't boot, so i tried to find a kernel to flash back, so the phone is booting again, the only one worked was that custom one, but not stable.
So I'm trying to find another better working kernel to flash, or an alternative way to reset my phone, but my recoverys aren't working.
LordImperator said:
I overflashed only the kernel, so the phone didn't boot, so i tried to find a kernel to flash back, so the phone is booting again, the only one worked was that custom one, but not stable.
So I'm trying to find another better working kernel to flash, or an alternative way to reset my phone, but my recoverys aren't working.
Click to expand...
Click to collapse
Flash stock recovery via adb fastboot..
And then perform dload method it will flash..
hassanjavaid8181 said:
Flash stock recovery via adb fastboot..
And then perform dload method it will flash..
Click to expand...
Click to collapse
But which stock recovery should i use?
LordImperator said:
But which stock recovery should i use?
Click to expand...
Click to collapse
B355 recovery..extract it via huawei update extractor..
And flash it via adb fastboot.
hassanjavaid8181 said:
B355 recovery..extract it via huawei update extractor..
And flash it via adb fastboot.
Click to expand...
Click to collapse
Only boot or also recovery, system, cust ...
LordImperator said:
Only boot or also recovery, system, cust ...
Click to expand...
Click to collapse
Firmware is in update.app.
Just extract recovery.IMG and flash it via fastboot like you flash twrp..
The put update.app(not extracted) in dload folder and press three button it will start flashing..
hassanjavaid8181 said:
Firmware is in update.app.
Just extract recovery.IMG and flash it via fastboot like you flash twrp..
The put update.app(not extracted) in dload folder and press three button it will start flashing..
Click to expand...
Click to collapse
I did, that but it says Software install failed!
I want the single Sim oeminfo.img for my p8 lite 2017 to install single Sim fw. Firmware could be Pralx1c432b169 and so on. Can you help me?
Wire1122 said:
I want the single Sim oeminfo.img for my p8 lite 2017 to install single Sim fw. Firmware could be Pralx1c432b169 and so on. Can you help me?
Click to expand...
Click to collapse
In page 3 there is the new download link. It is a dual sim oeminfo but there if you read a little about it it works exactly fine on a single sim variant too.
https://forum.xda-developers.com/p8...ussion/request-pra-lx1-oeminfo-t3581091/page3
Hope it helped
Ok, but to install a single Sim fw?
Wire1122 said:
Ok, but to install a single Sim fw?
Click to expand...
Click to collapse
It's your choice. In a normal situation that should work too
Can you explain it? I must flash oeminfo through twrp and then?
Wire1122 said:
Can you explain it? I must flash oeminfo through twrp and then?
Click to expand...
Click to collapse
Steps:
1. Download the latest full pra-lx1c432 firmware. - If you don't have it, download it from here: https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
2. Download huawei update extractor. -If you don't have it, download it from here: https://forum.xda-developers.com/showthread.php?t=2433454
3. Extract UPDATE.APP using HUE. You can find it inside the firmwire zip you just downloaded.
4. Using fastboot, you will need to flash: System, boot, recovery. (Move them to the adb location)
4. - This will take some time
a. fastboot flash system system.img
b. fastboot flash boot boot.img
c. fastboot flash recovery recovery.img
Now if you done, do a factory reset with stock recovery.
Your phone is now stock again.
GedeonTaylor said:
Steps:
1. Download the latest full pra-lx1c432 firmware. - If you don't have it, download it from here: https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
2. Download huawei update extractor. -If you don't have it, download it from here: https://forum.xda-developers.com/showthread.php?t=2433454
3. Extract UPDATE.APP using HUE. You can find it inside the firmwire zip you just downloaded.
4. Using fastboot, you will need to flash: System, boot, recovery. (Move them to the adb location)
4. - This will take some time
a. fastboot flash system system.img
b. fastboot flash boot boot.img
c. fastboot flash recovery recovery.img
Now if you done, do a factory reset with stock recovery.
Your phone is now stock again.
Click to expand...
Click to collapse
not working only bootloop
Wire112233 said:
not working only bootloop
Click to expand...
Click to collapse
Maybe something is not working how it should. Then connect to a usb cable which is plugged into you computer and hold vol up and pwr button. If you did it correctly now you are in erecovery. Download the latest. If it says it can't download then you are missing something..!
GedeonTaylor said:
Maybe something is not working how it should. Then connect to a usb cable which is plugged into you computer and hold vol up and pwr button. If you did it correctly now you are in erecovery. Download the latest. If it says it can't download then you are missing something..!
Click to expand...
Click to collapse
right but downloading b170 rom. I want b171 single sim not b170 dualsim
GedeonTaylor said:
Steps:
1. Download the latest full pra-lx1c432 firmware. - If you don't have it, download it from here: https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
2. Download huawei update extractor. -If you don't have it, download it from here: https://forum.xda-developers.com/showthread.php?t=2433454
3. Extract UPDATE.APP using HUE. You can find it inside the firmwire zip you just downloaded.
4. Using fastboot, you will need to flash: System, boot, recovery. (Move them to the adb location)
4. - This will take some time
a. fastboot flash system system.img
b. fastboot flash boot boot.img
c. fastboot flash recovery recovery.img
Now if you done, do a factory reset with stock recovery.
Your phone is now stock again.
Click to expand...
Click to collapse
The pra does not tolerate such flash orgies. Or did you test it before posting?
ChinHon said:
The pra does not tolerate such flash orgies. Or did you test it before posting?
Click to expand...
Click to collapse
chinhon, can you guides me to correcrly install b171 fw?
Wire112233 said:
chinhon, can you guides me to correcrly install b171 fw?
Click to expand...
Click to collapse
Use the Firmware Finder for this. I have no experience with it, but there are very good instructions at xda.
ChinHon said:
The pra does not tolerate such flash orgies. Or did you test it before posting?
Click to expand...
Click to collapse
Flash : system, boot & recovery image via bootloader ( if its already unlocked ) it should work on any Android devices ... I don't see why here, it should be different
surdu_petru said:
Flash : system, boot & recovery image via bootloader ( if its already unlocked ) it should work on any Android devices ... I don't see why here, it should be different
Click to expand...
Click to collapse
not working, after Huawei logo the smartphone reboot itself such after a factory reset
---------- Post added at 05:21 PM ---------- Previous post was at 05:17 PM ----------
ChinHon said:
Use the Firmware Finder for this. I have no experience with it, but there are very good instructions at xda.
Click to expand...
Click to collapse
not work. On device info only show the security patch to 5 february. The fw version is the same before, so b170
---------- Post added at 05:22 PM ---------- Previous post was at 05:21 PM ----------
ChinHon said:
Use the Firmware Finder for this. I have no experience with it, but there are very good instructions at xda.
Click to expand...
Click to collapse
not work. On device info only show the security patch to 5 february. The fw version is the same before, so b170
ChinHon said:
The pra does not tolerate such flash orgies. Or did you test it before posting?
Click to expand...
Click to collapse
Yes, I did..
surdu_petru said:
Flash : system, boot & recovery image via bootloader ( if its already unlocked ) it should work on any Android devices ... I don't see why here, it should be different
Click to expand...
Click to collapse
The PRA is a mystery. There's usually a brick in this. Often a bootloop. Sometimes it works. That's why I don't like to recommend it. Why I couldn't find out so far and therefore put a rescue rom online
ChinHon said:
The PRA is a mystery. There's usually a brick in this. Often a bootloop. Sometimes it works. That's why I don't like to recommend it. Why I couldn't find out so far and therefore put a rescue rom online
Click to expand...
Click to collapse
I don't understand the PRA myself..I've soft-bricked mine a couple of times and have recovered using different methods and not one foolproof way.
Can I flash stock fw with twrp?
No, unless someone has a backup for you. Take the K-Rom v. 3.3 and make it unroot. Then you have a stock rom.
Hey guys, now it's time for eRecovery!!
My device: PRA-LX1 (Dual SIM version)
Got bricked. I was installing Google APPS on EMUI (Dumb) and it just kept on looping and restarting.
I decided to try the rescue zip and when I successfully restore it, it boots back to TWRP after I reboot to system.
My recoverys: TWRP (installed on recovery2) and Stock EMUI Recovery (installed on recovery)
Bootloader: Unlocked
Fastboot: Command not allowed
Thanks in advance for your reply.
Hello, is the FRP status on fastboot mode LOCKED or UNLOCKED
if it's UNLOCKED then you can unbrick it using fastboot to flash boot.img system.img and do a full wipe of your data partition.
RAR1991 said:
Hello, is the FRP status on fastboot mode LOCKED or UNLOCKED
if it's UNLOCKED then you can unbrick it using fastboot to flash boot.img system.img and do a full wipe of your data partition.
Click to expand...
Click to collapse
I already booted, that's good news!
Now I've got a problem. The famous unbrick guide everyone uses - the firmware is buggy for me.
Fingerprint scanner doesn't work - camera doesn't work and audio doesn't work.
I think this is a problem with the firmware as they are more models of the PRA-LX1?
Btw, how do I find mine?
Thanks
My model is the Europe unlocked dual sim one
NetfariousIntent said:
I already booted, that's good news!
Now I've got a problem. The famous unbrick guide everyone uses - the firmware is buggy for me.
Fingerprint scanner doesn't work - camera doesn't work and audio doesn't work.
I think this is a problem with the firmware as they are more models of the PRA-LX1?
Btw, how do I find mine?
Thanks
My model is the Europe unlocked dual sim one
Click to expand...
Click to collapse
try to download the right version for your phone from firmware finder and flash it using fastboot
RAR1991 said:
try to download the right version for your phone from firmware finder and flash it using fastboot
Click to expand...
Click to collapse
Oh, I think I have picked the right version, now I get the Update.app, how can I flash it now?
I'm such a noob, thank you for your answer.
NetfariousIntent said:
Oh, I think I have picked the right version, now I get the Update.app, how can I flash it now?
I'm such a noob, thank you for your answer.
Click to expand...
Click to collapse
you have to use Huawei update extractor to extract system.img boot.img recovery and recovery2 then flash them with fastboot
PS: Make a backup before trying anything
https://forum.xda-developers.com/showthread.php?t=2433454
thank you
RAR1991 said:
you have to use Huawei update extractor to extract system.img boot.img recovery and recovery2 then flash them with fastboot
PS: Make a backup before trying anything
https://forum.xda-developers.com/showthread.php?t=2433454
Click to expand...
Click to collapse
Only system, boot, recovery and recovery2?
What about modem, vendor, etc...?
Thanks
NetfariousIntent said:
Only system, boot, recovery and recovery2?
What about modem, vendor, etc...?
Thanks
Click to expand...
Click to collapse
in all tutorials that's all what they mentioned and you can't flash vendor.img from fastboot I've tried that but it returns (Command not allowed) I'm trying to convert vendor.img to flashable TWRP backup using Imgtool but I can't figure out how it works yet
RAR1991 said:
in all tutorials that's all what they mentioned and you can't flash vendor.img from fastboot I've tried that but it returns (Command not allowed) I'm trying to convert vendor.img to flashable TWRP backup using Imgtool but I can't figure out how it works yet
Click to expand...
Click to collapse
Hi, I've tried to flash my firmware. Now It bootloops for a while and then restarts and bootloops agian.
I guess I'm very unlucky.
Thanks
NetfariousIntent said:
Hi, I've tried to flash my firmware. Now It bootloops for a while and then restarts and bootloops agian.
I guess I'm very unlucky.
Thanks
Click to expand...
Click to collapse
I'm experiencing the same thing right now with my PRA-LA1 and the only way that I found to make it works is to install a TWRP recovery and root it. But I have a lot of bugs after that I've already created a thread for that if someone can help
[Help] Bugs after rooting PRA-LA1