Database Develop

Unbrick Revolution from LG Screen

GOOD NEWS! Unless your power button does not work, the Revolution IS unbrickable! After searching far and wide for a method to unbrick my phone from the lg boot screen, I found a way! By now you have hopefully been to all of the other threads and downloaded and installed LGNPST and all of that hoopla so I will just post links and not full directions...here we go:
1) Download and install LGNPST and associated files
forum.xda-developers.com/showthread.php?t=1337386
http://forum.xda-developers.com/showthread.php?t=1466655
2) Follow directions all the way through step 11
forum.xda-developers.com/showthread.php?t=1337386
3) Remove your battery and connect your phone via usb (the hard buttons on the bottom of the phone should blink slowly).
**Make sure battery is at least 25% charged
4) Hold down power + vol up.
5) Phone will come on and read "downloading do not remove cord" or something to that nature. Put battery back in.
6) If you followed step 2 correctly, LGNPST will now show an unknown device and will be in emergency phone book mode. Under the emergency tab it will ask you for 1) a .dll file and 2) a phone book. Click on the folder icon next to .dll file and load the VS910.dll from wherever you have it saved. Click on the folder icon next to phone book. Navigate to the folder where you have saved the correct .tot file. in the "file name" box type *.* and hit enter. If you are in the correct folder you should now see the .tot file, click on it then click "save".
7) Back on the LGNPST screen click on start. It should now say MASTERBIN and a percentage ticking up (if not you have done something wrong).
8) once completed commence re-rooting!
forum.xda-developers.com/showthread.php?t=1348557&highlight=root+v7
special thanks to:
mtmichaelson for his awesome root package!!!
jackpot08 for LGNPST
and all of those who have kept the .tot files movin'
I hope this helps!!!

Good post, this method does work as a last resort, but be warned.. flashing a tot file from the emergency download mode like this will most likely get you stuck in "test mode" -- no more usb mass storage (and possibly other problems).
And so far noone knows how to get out of test mode...

All it took was a simple google search...
https://forun.xda-developers.com/showthread.php?t=151279
https://forun.xda-developers.com/showthread.php?t=151279
Sent from my VS910 4G using XDA

un_brickable said:
All it took was a simple google search...
https://forun.xda-developers.com/showthread.php?t=151279
https://forun.xda-developers.com/showthread.php?t=151279
Sent from my VS910 4G using XDA
Click to expand...
Click to collapse
Broken link to a "fix" that is more of a bandaid than a fix, as it requires you to downgrade to froyo.
Sent from my VS910 4G using XDA

Yep.. believe me I searched... and searched and searched until my eyes almost popped out of my head
Nonetheless I'll take test mode over a bricked phone with a fresh 2 year contract any day...

Links for this AND instructions are posted in like 3 other threads lol.
Sent from my AXI0M ICS RAZR using tapatalk.

emergency download mode real way
to get the lg to work with lgnpst i had to open the program then with battery out but held to bottom with fingers ready to put in quickly hold vol up then plug usb to computer then slide battery in quickly and hold power button while still holding vol up if anyone is having problems with lg revo and lgnpst send me a message i spent a week doing everything n finally figured it out

mjollnir2012 said:
to get the lg to work with lgnpst i had to open the program then with battery out but held to bottom with fingers ready to put in quickly hold vol up then plug usb to computer then slide battery in quickly and hold power button while still holding vol up if anyone is having problems with lg revo and lgnpst send me a message i spent a week doing everything n finally figured it out
Click to expand...
Click to collapse
You do not have to go through all that if you have the proper drivers.
Sent from my AXI0M ICS RAZR using tapatalk.

Replace your lg revolution for free
Flashing to v4 froyo tot will not leave the the phone in test mode or rooted. If you can get your phone back to froyo with no test mode then you can bring the phone back, and tell them the phone will not update. I have had two phones already and for some reason they will not take the ota updates. The carrier had no idea I rooted/unrooted and flashed oh so many times. Just a suggestion for noobs who do not want to spend hours or days or maybe even weeks trying to get this phone to work correctly.

Help please
I have tried above and I cant seem to get drivers to install properly
The only one that installs properly is USB Composite device and the LGE CDMA USB does not install properly. I flashed wrong recovery from ROM Manager and stuck at LG screen. LGNPST does not capture my phone. What else should or can I do besides take it in?

drivers
i put both LGAndroidDriver_Ver_1.0_All and LG VZW_United_WHQL_v2.4.1 and they installed correctly is ur phone stuck or can it boot

unbrick Lg revo info
I downloaded the files and had an issue extracting the rom .tot file , How do I extract the .tot so I can use them with the LGNPST.
I have followed the directions and found The LGNPST program comes up blank with no phone info. I am guessing it is because of the .tot files not being "extracted " . I sure would appreciate some help on this one. My phone is bricked.

tommy_guns said:
I downloaded the files and had an issue extracting the rom .tot file , How do I extract the .tot so I can use them with the LGNPST.
I have followed the directions and found The LGNPST program comes up blank with no phone info. I am guessing it is because of the .tot files not being "extracted " . I sure would appreciate some help on this one. My phone is bricked.
Click to expand...
Click to collapse
When you download the .tot file, it should be a zip file. Just extract the zip file using WinRAR or 7zip to somewhere it's easy to find.
If it's not a zip file, then chances are it's already extracted and you don't need to do it.
If LGPNST is coming up blank even though your phone is plugged in, then you need to install the correct drivers or try a different USB cable or a different USB port because it means LGPNST can't connect to your device.

spc_hicks09 said:
When you download the .tot file, it should be a zip file. Just extract the zip file using WinRAR or 7zip to somewhere it's easy to find.
If it's not a zip file, then chances are it's already extracted and you don't need to do it.
If LGPNST is coming up blank even though your phone is plugged in, then you need to install the correct drivers or try a different USB cable or a different USB port because it means LGPNST can't connect to your device.
Click to expand...
Click to collapse
Forgot if it's in Internet Connection and USB Debugging Enabled too.

Gel Pen6 said:
Forgot if it's in Internet Connection and USB Debugging Enabled too.
Click to expand...
Click to collapse
Sure did, thank you! Yes make sure you have selected the option for "Internet Connection" and USB Debugging is enabled.

unbrick Lg revo info
I can't get it to internet connection because i can't boot into anything . It is like it is stuck at boot. also the .tot files do not extract with any zip program . I have loaded the vs910.dll and the drivers onto my computer but the LGNPST program still not recognizing any phone. for that matter the the computer has not recognized the phone , maybe due to I cannot set internet connection mode. The USB De bug was enabled before all this started.
The whole situation of not completing boot came about when I happened defrosted the astro file manager app. Help

tommy_guns said:
I can't get it to internet connection because i can't boot into anything . It is like it is stuck at boot. also the .tot files do not extract with any zip program . I have loaded the vs910.dll and the drivers onto my computer but the LGNPST program still not recognizing any phone. for that matter the the computer has not recognized the phone , maybe due to I cannot set internet connection mode. The USB De bug was enabled before all this started.
The whole situation of not completing boot came about when I happened defrosted the astro file manager app. Help
Click to expand...
Click to collapse
u gotta open lgnpst then plug your phone on to be put on emergency download mode also the .tot file is already extracted like was already said in a previous post and make sure u register the .dll

Evnoth said:
Flashing to v4 froyo tot will not leave the the phone in test mode or rooted. If you can get your phone back to froyo with no test mode then you can bring the phone back, and tell them the phone will not update. I have had two phones already and for some reason they will not take the ota updates. The carrier had no idea I rooted/unrooted and flashed oh so many times. Just a suggestion for noobs who do not want to spend hours or days or maybe even weeks trying to get this phone to work correctly.
Click to expand...
Click to collapse
I had a few issues with this namely Tots not loading right getting perm black screen, I pulled the batt, put it back in and did a hard reset (wipe) back to stock then rooted added CWM with MT's hlep of course and am now re flashing gingervolt to broken out 1.1 and still puts me back in test mode, even restoring older backups put me in test mode, only v4 seems to work....WHY?

Thanks I finally got it back running with the LGNPST , tot version 7 . The phone works now but I also am in test mode and cannot switch my usb. Question, Can I use The LGNPST and select tot version 4 and install that as before to get my usb back. And if so will I then be able to get OTA updates or will I have to return it to store for that. I hate being stuck in test. What happens with phone stuck in test ?

tommy_guns said:
Thanks I finally got it back running with the LGNPST , tot version 7 . The phone works now but I also am in test mode and cannot switch my usb. Question, Can I use The LGNPST and select tot version 4 and install that as before to get my usb back. And if so will I then be able to get OTA updates or will I have to return it to store for that. I hate being stuck in test. What happens with phone stuck in test ?
Click to expand...
Click to collapse
You'll be able to get OTAs but you'll still be stuck in test mode. To this day there is no known method (yet) to get out of test mode. Someone correct me if I'm wrong but the only difference I know of with test mode is that you can't transfer files via USB cable anymore. You have to either use adb or an adapter for your microSD card to your PC.
Sent from my DROID RAZR using Tapatalk

PLEASE HELP, Computer is not recognizing my Galaxy S

Just got my phone into download mode after using the jig, and i have been able to connect to my pc before i seriously F'd my phone by messing with a setting in cwm. I have downloaded and redownloaded drivers from samsungs website, along with installing Kies and that does not recognize my phone. (also i would like to add i am unable to access the phone since it wont turn on without the jig, without jig it just goes into a boot loop.)
THis is what happens when i plug my phone into the computer:
plug in usb (to computer and phone)
let it do its thing to recognize device...
pop-up stating "unknown device" so i click it.
then right-click the unknown device which opens up another window
from this menu it shows Install driver, Update driver and 3 other options.
when i press install driver and update driver, it tells me that the driver is already installed in "device unknown."
At this point i throw computer at wall after 2 days of trying to figure this out.

so messed around and the problem only happens when it is in download mode. but when it is not in download mode it shows up but no use to me because i am trying to flash it to stock. soo i dont know why the error 43 only shows up when in download mode. any help would be great.

sean.hunt said:
so messed around and the problem only happens when it is in download mode. but when it is not in download mode it shows up but no use to me because i am trying to flash it to stock. soo i dont know why the error 43 only shows up when in download mode. any help would be great.
Click to expand...
Click to collapse
Just follow this to update the drivers http://forum.xda-developers.com/showpost.php?p=27205737&postcount=4571 , same thing as what you have done earlier but this time , when it searches for new drivers, you can do the selection for it.
But first reboot your PC after pulling out power cord ...and try the quick solutions first

Ok sen, so i tried to install the driver manually but i am stuck at the part where i have to install something on my phone to allow it to sync with the computer, since my phone will not even boot up. I am starting to think my dear Capi is going to be a paper weight =(

Bricked Samsung Gear Live - Please help.

Hi,
Am a novice when it comes to rooting, unlocking android devices. So please excuse my ignorance and my long-winded style of writing. I want the expert users to educate me on this issue and so I don't want to miss any trivial (or not so trivial) information.
1) So, I got Samsung gear live from ebay. It came with a sprat-userdebug 5.0.1. After googling I found out that it's a user/refurb build and can't be updated to 5.1.1
2) Thanks to rootjunky! I used Gear live restore tool V3 and unlocked the bootloader (option 2). Faced few issues in getting the driver. However, fixed everything and unlocked it. Flast TWRPd it (option 8). Flashed recovery (option 4) and bootimage (option 5). Then I sideloaded stock image from 4.4W.2 (using boot.img and system.img). That was the version I found after googling.
3) Then I tried to update it via OTA download. Download completed and it went back to recovery mode and did't apply the download. There was an error message that said something like "Unable to verify the download"
4) Tried multiple times and no luck with that
5) Then tried to sideload new version 5.1.1 LCA43 from xda wiki page. However, when my device went to recovery mode, my pc lost the connection and i wasn't able to sideload (received - device "null" not found" - error from adb command)
6) Until this point I was able to pair my device with my samsung S5 phone and only problem was not able to install the update
7) Then I reset my watch to factory setting, restarted multiple times, went to recovery mode to boot as a new device etc. No luck
8) Then I did something I shouldn't have done (or I think I shouldn't have done). Used option 7 root gear live. When the system went to SH mode, I panicked and closed the cmd prompt and hard reset the device by holding power button
9) After this step, I was not able to pair my device with my phone. Now the version says 4.4W.1 - KGW42N
10) Tried resetting my device, restarted it, used recovery mode to restart it, revoked all debug access, deleted adbkey from my PC, uninstalled android SDK, all drivers, etc. Reinstalled it again with no help.
11)Suddenly android wear in my phone sees my wifirouter as a device (strange)
11) When I plug in the device to my Pc, I could see it in my device manager. When I use recovery tool it says unregistered device and asking me to register it via my phone. Where as am not able to pair it with my phone. Tried to pair it with a new phone (moto e) and no help either
12)Somewhere read that disabling wifi in the phone before pairing works. Tried that and no luck
So here am with a bricked device that stays in the screen where it says "install android wear in your phone" and detects nothing else. Am able to go to bootloader mode, recovery mode from the device. However when it's in recovery mode, my PC doesn't detect it. Even the recovery tool says unregistered device.
Please help in unbricking this device and thank you for reading thru the whole problem. Any help would be much appreciated!

Use Gear live restore tool v2. Lots of known issues with v3

Thanks for the reply. I will try this. However, how will I make my device discoverable? Now, none of my phones detect my device.
So I guess I will get "Unauthorized Device" error when I use recovery tool. Could you please let me know if there's other way around? Or am i missing something?

I've never used it
Pretty sure all the info you need is in the thread
http://forum.xda-developers.com/gear-live/development/utility-gear-live-watch-tool-t2846696

No luck. Tried V2. Tool doesn't recognize my watch. It says 'Device Unauthorized. Please check the confirmation dialog on your device'. My device is stuck in 'Install Android wear on your phone' screen.

unbricked using v2 of the tool. Now trying to update the os version. Will see if I can get lucky this time. Thanks for the help!

All is good now. Now my gear live is running on 5.1.1 with latest updates.

Good work

Please can you tell what exactly you done, as I'm on the same root.. and I'm using win 10... but without any luck so far..

darwchprish said:
Please can you tell what exactly you done, as I'm on the same root.. and I'm using win 10... but without any luck so far..
Click to expand...
Click to collapse
Simple procedure.
Just download v2 of this tool
Make sure to install USB drivers
Unlock bootloader - option 2
Then use option 6 to flash it. Then you'll get new OTA updates.
Refer rootjunky video - https://www.youtube.com/watch?v=x7oRjESQh_o

I'm not able to pair my device with my phone. Now the version says 4.4W.1 - KGW42N,
and ... I tried V2 and V3. Tool but doesn't recognize my watch. It says 'Device Unauthorized. My device is stuck in 'Install Android wear on your phone' screen.

darwchprish said:
I'm not able to pair my device with my phone. Now the version says 4.4W.1 - KGW42N,
and ... I tried V2 and V3. Tool but doesn't recognize my watch. It says 'Device Unauthorized. My device is stuck in 'Install Android wear on your phone' screen.
Click to expand...
Click to collapse
Follow this procedure.
1)Make sure all drivers are installed properly in your PC
2) Make sure when you connect your device to your PC, it's discovered as unauthorized device. It's ok
3) Long press power button in the device and swipe from top left to botom right corner when you see samsung gear live logo
4)This will get the device to bootloader mode
5)Now connect the device to your PC and run V2 of the tool. Your device will be discovered in fastboot mode
6)Now select option 6 to flash the device to stock. It'll flash it
7) Now swipe down to highlight start and swipe from right to left to start. If it goes to Raw dump code = 6. do a hard restart by long pressing power button. You'll get back your device in original setting.
Check rootjunky youtube video to get the live demo of this procedure.

noviceinandroid said:
No luck. Tried V2. Tool doesn't recognize my watch. It says 'Device Unauthorized. Please check the confirmation dialog on your device'. My device is stuck in 'Install Android wear on your phone' screen.
Click to expand...
Click to collapse
How did you get past this? I'm stuck here now too.
-- update after trying that procedure again, it worked to get to fastboot mode. Now I'm doing that 'option 6' to flash it.

mike061215 said:
How did you get past this? I'm stuck here now too.
-- update after trying that procedure again, it worked to get to fastboot mode. Now I'm doing that 'option 6' to flash it.
Click to expand...
Click to collapse
Good luck.

It worked -- and I finally got the OS to update an all that and now I finally have a functional Gear Live. Phew!

My Gear Live was bricked a lot... Computer detect device as RELINK HS-USB QDLoader 9008. Has anyone any idea how fix it?

lamik91 said:
My Gear Live was bricked a lot... Computer detect device as RELINK HS-USB QDLoader 9008. Has anyone any idea how fix it?
Click to expand...
Click to collapse
sounds like USB driver issue. Please install correct drivers and follow the steps mentioned above. It should be unbricked.

Where can i find correct drivers? Additionally my Gear Live doesn't turn on and has only black screen.

I am confused on how to use the tool. My watch is stuck at the Install Android Wear App and won't do anything short of turning it off. How do I enable developer mode \ debugging without being able to get to the watch settings. Please help! Thanks

pedalquickly said:
I am confused on how to use the tool. My watch is stuck at the Install Android Wear App and won't do anything short of turning it off. How do I enable developer mode \ debugging without being able to get to the watch settings. Please help! Thanks
Click to expand...
Click to collapse
You need to factory reset first of all. After that let connect to your wifi, the updates will download on their own. They put a new one out today. I can't go into how but if you look at the forum and search the answers are there. There's even a tool to use.
Sent from my SM-N910T3 using XDA-Developers mobile app

Secure booting error 1003

So I think I may have bricked my phone unless I can get the H811 20i KDZ file but even that may not be good enough to save it. I'll start with where I am currently at. On boot I get the error:
Secure booting error!
Error code: 1003
Modified
I am able to get into download mode by pressing the up volume key or into the wipe mode by pressing the down volume key. However, no matter what I try I can't seem to get it to reboot normally.
Here is what I did to get myself into this situation:
I stepped through the guide to install MM and then I performed the fastboot OEM unlock and booted into TWRP. I then installed SuperSU and rebooted. Then for reasons unknown I decided I would relock the boot loader and so I ran the command fastboot oem lock. I fully understand the stupidity of that thought now but didn't think very clearly at the time.
Here is what I have tried:
Using the LG Support Tool I attempted an Upgrade Recovery which failed.
Using the guide on here to return to stock I attempted the method using the kdz file for h811 10n but that fails at the upgrading your phone with the error message "Upgrade stopped due to an error". I have attempted the retry button numerous times without any change in responses.
At this point in time I am game to try anything.
:fingers-crossed:

Thanks to autoprime I am now downloading the kdz for MM and when it is complete I will attempt to use LGUP to restore it.
Well I get an error message from LGUP stating that I don't have the correct DLL for H81120i installed. I attempted to replace the dll with the one inside the MM kdz but that didn't work.

bbenz3 said:
Thanks to autoprime I am now downloading the kdz for MM and when it is complete I will attempt to use LGUP to restore it.
Well I get an error message from LGUP stating that I don't have the correct DLL for H81120i installed. I attempted to replace the dll with the one inside the MM kdz but that didn't work.
Click to expand...
Click to collapse
Use LGBridge. Put it in download mode. Click on update error recovery.

Vseprz said:
Use LGBridge. Put it in download mode. Click on update error recovery.
Click to expand...
Click to collapse
Oh I wish it were that simple. I had tried it last night but attempted it again as I couldn't remember what happened. I get an error message stating "Connect your mobile device to the USB port. If it is already connected, contact LG customer service."
At this point I think I may just need the MM dll to use with LGUP. I attempted to use an MSI packaging utility to replace the dll in the 0.0.3.23 installer with the dll I extracted from the kdz file but that got me nowhere.

I attempted to use the LG FlashTool v1.8 and found out that the dll that I extracted is ver 0.0.3.21 which is older than the msi version found on here. Does anyone know how to get a newer one?

bbenz3 said:
Oh I wish it were that simple. I had tried it last night but attempted it again as I couldn't remember what happened. I get an error message stating "Connect your mobile device to the USB port. If it is already connected, contact LG customer service."
At this point I think I may just need the MM dll to use with LGUP. I attempted to use an MSI packaging utility to replace the dll in the 0.0.3.23 installer with the dll I extracted from the kdz file but that got me nowhere.
Click to expand...
Click to collapse
I had the same error and sucessfully used lgbridge. You probably need to reinstall your usb drivers.

OK I'll give that a shot.
No go...
I uninstalled anything I could find related to LG. I then reinstalled the LG Bridge software which then updated the USB drivers to 4.0.4. I then rebooted my computer and attempted it again and I got nothing but the same error.

bbenz3 said:
OK I'll give that a shot.
No go...
I uninstalled anything I could find related to LG. I then reinstalled the LG Bridge software which then updated the USB drivers to 4.0.4. I then rebooted my computer and attempted it again and I got nothing but the same error.
Click to expand...
Click to collapse
I had this exact same issue when upgrading my phone. Didn't do it correctly and it took me about 3 hours before I got my phone working again. It was about a week ago on another computer, but I'll try to recall what I did when it finally clicked in my mind.
Download H81120i_00_0201.kdz flashable zip from here (1.6GB Feb-04-16):
http://downloads.codefi.re/autoprime/LG/LG_G4/H811/H81120i/
Download LGUP and install it. I used the DropBox link in this thread:
http://forum.xda-developers.com/g4/help/lgup-install-kdz-mm-lp-t3249803
Remember to install the LGUP_8994_DLL file BEFORE LGUP_Install
Download and install LG Bridge (for the USB drivers) here:
http://www.lg.com/uk/support/pc-suite
Select the LG 815 model, the drivers will work. I only used the LG Bridge to install the USB drivers. Nothing else.
OK, now here's where your phone comes in.
Step 1: Turn off your phone (pull the battery if you must, but put it back in).
Step 2: Hold the VOLUME UP button and plug the USB cable into your PC. This puts your phone into DOWNLOAD MODE.
Step 3: On your PC, open up LGUP. The program shoud recognize the phone as H811 in COM3 or COM4. Highlight it and click the SELECT button.
Step 4: Under the "Process" row, select UPGRADE
Step 5: Click the blank space under File Path, it will pop up a [...] [X] at the end. Click the [...].
Step 6: Select the H81120i_00_0201.kdz and click on Start. The program will push the STOCK H811 MM ROM to your phone. This will bring your phone out of Brick mode, but you will have to go through the entire rooting process again.

Donut42 said:
I had this exact same issue when upgrading my phone. Didn't do it correctly and it took me about 3 hours before I got my phone working again. It was about a week ago on another computer, but I'll try to recall what I did when it finally clicked in my mind.......
Click to expand...
Click to collapse
Woohoo!!!!!!!!!!!!!! I changed two things and I'm not certain which one it was that finally made it work but I followed your steps and installed the LGUP_DLL before the application (upon re-reading the original thread for the LGUP program I see that is the way you were supposed to do it the whole time, so much for reading comprehension) and the other was I ran it from a Win 7 VM instead of Win 10.
Big thanks to you and also to bender_007 for walking me through a bunch of stuff and recommending the VM approach.

I did the exact same thing, but I cannot get LGUP to recognize my device. Uninstalled and reinstalled drivers and all. Any other ideas?

I did the following:
Installed Windows 7 in a VM
Installed the LG Bridge software and ran in do it should update
Installed the LGUP DLL
Installed the LGUP software
Connected phone to VM
Then ran LGUP tool

bbenz3 said:
I did the following:
Installed Windows 7 in a VM
Installed the LG Bridge software and ran in do it should update
Installed the LGUP DLL
Installed the LGUP software
Connected phone to VM
Then ran LGUP tool
Click to expand...
Click to collapse
Just tried this, but still showing as unknown device. I thought that was going to work.
---------- Post added at 04:39 AM ---------- Previous post was at 04:20 AM ----------
What does the phone show up in Device Manager as when it is in download manager? Mine is showing as LGE Androidnet USB Serial Port. Is this the same for you?

hv same problem. but problem is pc can't recognize the phone for below step:
Step 3: On your PC, open up LGUP. The program shoud recognize the phone as H811 in COM3 or COM4. Highlight it and click the SELECT button.
can recognize another G4.

ilovelg4ever said:
hv same problem. but problem is pc can't recognize the phone for below step:
Step 3: On your PC, open up LGUP. The program shoud recognize the phone as H811 in COM3 or COM4. Highlight it and click the SELECT button.
can recognize another G4.
Click to expand...
Click to collapse
same... I think it might have to do with the from that was installed when I relocked the boorloader. I'm so stupid for that.
I was trying different drivers, but none have helped lgup to recognize my phone.

esteho said:
same... I think it might have to do with the from that was installed when I relocked the boorloader. I'm so stupid for that.
I was trying different drivers, but none have helped lgup to recognize my phone.
Click to expand...
Click to collapse
first of all, how can we make PC detect our G4?
actually, even w/o any drive installed in PC, the PC should detect G4 if it works normally.

Device Manager shows my device, but as "LGE AndroidNet USB Serial Port". From what I have read this may be it's bricked mode. Is there anyone with an idea on how to come back from this?

esteho said:
same... I think it might have to do with the from that was installed when I relocked the boorloader. I'm so stupid for that.
I was trying different drivers, but none have helped lgup to recognize my phone.
Click to expand...
Click to collapse
saaaaame......
model COM Ports
unknwon [com41, xTreme 3]
Can't use Send_command too.
MM relocked the boorloader was stupid.

I had this exact error yesterday. I used cdmatool to get some bands enabled so I could get AT&T LTE with an AT&T sim and T-Mobile phone. All went well, and on my way out I figured since I had done the fastboot oem unlock, I should probably relock it. BAD IDEA.
By the time I found this article I had figured that somehow I needed to reflash to a ROM with a unmodified bootloader. This article is great! Such a rare treasure - all of the links to the necessary software and a short-but-sweet guide all in one. This post saved me hours, maybe days, of searching and trial-and-error.
By the way, since I had already installed the LG device drivers (available here) it was not necessary to download and install the whole LG Bridge.
THANKS!

Many times tried to flash my H811 to 20i but always ended with blank screen...is it have to wait until 5 to 10 minutes to get the phone rebooted after flashing with LGUP? Because usually ended with blank screen and qd mode, have to revive using qfil, imei unknown, camera and google play store always closes.

Hard brick help 911

I'm in a big predicament. A few weeks ago I installed the MOAR ROM on my Note 5. After installing this ROM I was no longer able to connect my phone to PC. I tried a Windows 8 PC which says I have an unrecognized USB device plugged in. I tried going into Developer settings to set USB mode to MTP but the option didn't exist. I had all USB drivers installed as well. My wife's phone is recognized no problem. When plugging the phone into my linux machine absolutely nothing happened. It used to show the phone in the left navigation panel in my window manager but after installing MOAR ROM it was no longer detected.
Anyway, today I was trying to play Cartoon Wars 3 and since my phone is rooted it wouldn't let me play. I decided to go into the Super User app and disable it to see if the game would work and it didn't. When I went to re-enable the app it said installation failed and asked me to reboot. I clicked reboot and was sent into a boot loop. I thought okay no big deal, I'll just restore a backup in TWRP. When I go to restore the backup and select the backup file it asks which partitions to restore, but there are no boxes to check. It usually has options like system and data but now it's just blank. I tried a factory reset and I'm still in a bootloop. I'm at a complete loss. I don't know what else to do. I've tried download mode and everything but no matter what I do my phone isn't detected by my pc.
I appreciate any help. I don't know what to do. I'm out of a phone right now and don't have a backup. Not to mention I'm in between jobs right now and can't afford a new one right now.

Just flash a stock rom from sammobile.com
Pre req:
*Odin(any vers)
*Stock rom
Steps
*Extract the downloaded stock rom in your PC
*In twrp wipe everything except internal, then boot in to download mode.
*Once in download mode, connect your phone to your pc, then open Odin.
*In Odin, check the "AP" section and locate the downloaded stock rom(the extracted one)
*Hit start.
Hpe that helps

herculesPh said:
Just flash a stock rom from sammobile.com
Pre req:
*Odin(any vers)
*Stock rom
Steps
*Extract the downloaded stock rom in your PC
*In twrp wipe everything except internal, then boot in to download mode.
*Once in download mode, connect your phone to your pc, then open Odin.
*In Odin, check the "AP" section and locate the downloaded stock rom(the extracted one)
*Hit start.
Hpe that helps
Click to expand...
Click to collapse
Thank you for your reply but it seems you didn't read my post. My phone is not recognized by any pc.

What is the terminal command to restore a backup? That's pretty much my last ditch effort.

Well I broke my recovery so I'm screwed. I contacted Samsung and they said they would service it for free. Wish me luck.

What would cause the phone to stop being recognized by the PC? I narrowed it down to the MTP software or the micro usb charge port. My Windows computer says Device Descriptor Request Failed. Linux box does nothing. No USB devices are listed when I run lsblk.

weinerwad3000 said:
I'm in a big predicament. A few weeks ago I installed the MOAR ROM on my Note 5. After installing this ROM I was no longer able to connect my phone to PC. I tried a Windows 8 PC which says I have an unrecognized USB device plugged in. I tried going into Developer settings to set USB mode to MTP but the option didn't exist. I had all USB drivers installed as well. My wife's phone is recognized no problem. When plugging the phone into my linux machine absolutely nothing happened. It used to show the phone in the left navigation panel in my window manager but after installing MOAR ROM it was no longer detected.
Anyway, today I was trying to play Cartoon Wars 3 and since my phone is rooted it wouldn't let me play. I decided to go into the Super User app and disable it to see if the game would work and it didn't. When I went to re-enable the app it said installation failed and asked me to reboot. I clicked reboot and was sent into a boot loop. I thought okay no big deal, I'll just restore a backup in TWRP. When I go to restore the backup and select the backup file it asks which partitions to restore, but there are no boxes to check. It usually has options like system and data but now it's just blank. I tried a factory reset and I'm still in a bootloop. I'm at a complete loss. I don't know what else to do. I've tried download mode and everything but no matter what I do my phone isn't detected by my pc.
I appreciate any help. I don't know what to do. I'm out of a phone right now and don't have a backup. Not to mention I'm in between jobs right now and can't afford a new one right now.
Click to expand...
Click to collapse
you can try this code and test if it work
*#0808#

Familiaaa said:
you can try this code and test if it work
*#0808#
Click to expand...
Click to collapse
The phone does not boot. Recovery does not boot. The only thing the phone does is go into download mode. The phone does not connect to any computer so I cannot use odin.

weinerwad3000 said:
The phone does not boot. Recovery does not boot. The only thing the phone does is go into download mode. The phone does not connect to any computer so I cannot use odin.
Click to expand...
Click to collapse
when your phone is in download mode,it doesn't work to connect it with samsung kies on your pc?
You could try using the Kies software to reload the stock firmware. Here's an overview of what to do:
- if you don't already have the Kies software installed on your PC, download it (just search Google) and install it. The first time it runs it'll update itself to the latest version so make sure you run it once before proceeding.
- put your phone in Download mode: with the phone completely off, press and hold the Volume Down and Home and Power buttons simultaneously, and release them all when you see the Samsung splash screen
- connect the phone to your PC with the USB cable that came with the phone
-- if you've never had the phone connected to your Windows-based computer before, you'll see messages about installing drivers, etc - just wait until this is done (may take 5 or 10 minutes) [I don't know what happens if you have a Mac - it probably just works]
- in the Kies software, select the second item in the Tools menu and just follow the prompts to enter the model number (in CAPS) and IMEI/Serial Number (both found under the battery - it's ok to remove the battery at this point)
- the Kies software should start downloading the correct firmware for your phone from the Internet; once that's done (depending on your Internet connection speed) it'll begin downloading that to the phone (this probably takes 10 minutes or so)

jubei79 said:
when your phone is in download mode,it doesn't work to connect it with samsung kies on your pc?
You could try using the Kies software to reload the stock firmware. Here's an overview of what to do:
- if you don't already have the Kies software installed on your PC, download it (just search Google) and install it. The first time it runs it'll update itself to the latest version so make sure you run it once before proceeding.
- put your phone in Download mode: with the phone completely off, press and hold the Volume Down and Home and Power buttons simultaneously, and release them all when you see the Samsung splash screen
- connect the phone to your PC with the USB cable that came with the phone
-- if you've never had the phone connected to your Windows-based computer before, you'll see messages about installing drivers, etc - just wait until this is done (may take 5 or 10 minutes) [I don't know what happens if you have a Mac - it probably just works]
- in the Kies software, select the second item in the Tools menu and just follow the prompts to enter the model number (in CAPS) and IMEI/Serial Number (both found under the battery - it's ok to remove the battery at this point)
- the Kies software should start downloading the correct firmware for your phone from the Internet; once that's done (depending on your Internet connection speed) it'll begin downloading that to the phone (this probably takes 10 minutes or so)
Click to expand...
Click to collapse
Kies doesn't work either. I already tried that. When I hook up the phone It says "Device Descriptor Request Failed". It used to connect to my computers until I put MOAR ROM on the phone. Since then it stopped being recognized by my computers. There's either something wrong with the connection or something got corrupted.

weinerwad3000 said:
Kies doesn't work either. I already tried that. When I hook up the phone It says "Device Descriptor Request Failed". It used to connect to my computers until I put MOAR ROM on the phone. Since then it stopped being recognized by my computers. There's either something wrong with the connection or something got corrupted.
Click to expand...
Click to collapse
What have you already tried?
- are you sure you're using a data cable and not a charging-only cable?
- have you tried a different computer?
- have you installed the Kies software?
- what does Device Manager show when the phone is connected?
- assuming that the phone is working normally, does the phone show anything when you connect it?
- do you have try windows 8 or 10?
can be you found a solution in this forum
http://forums.androidcentral.com/sa...-not-being-recognised-download-mode-odin.html

jubei79 said:
What have you already tried?
- are you sure you're using a data cable and not a charging-only cable?
- have you tried a different computer?
- have you installed the Kies software?
- what does Device Manager show when the phone is connected?
- assuming that the phone is working normally, does the phone show anything when you connect it?
- do you have try windows 8 or 10?
can be you found a solution in this forum
http://forums.androidcentral.com/sa...-not-being-recognised-download-mode-odin.html
Click to expand...
Click to collapse
I've tried 4 different cables. My wife's S5 works perfectly fine on all computers. I have tried in Windows 7, 8, 8.1, and 10. I've also tried in Linux Mint. It used to work until I installed MOAR Rom. Windows says Device Descriptor Request Failed. Linux doesn't do anything when hooked up. lsblk doesn't show the device either.

I have a bit of an update. Apparently something happened with all my data cables. I hooked up my wife's phone the other day and I was all of a sudden receiving the same error as the note 5. I went out and bought a new data cable and now her phone connects again. I'm waiting for the Note 5 to charge up so I can try Odin. I'll post back my results.
I apologize to those who told me it was the cable. I just didn't see that it was conceivable that all 4 of my data cables were all of a sudden damaged. Never underestimate the ability of children to destroy every working cable you own.

Well I'm still getting the error. I have some usb cables coming in the mail so once i try those out I'll get back to everyone.

weinerwad3000 said:
Well I'm still getting the error. I have some usb cables coming in the mail so once i try those out I'll get back to everyone.
Click to expand...
Click to collapse
Were you able to fix your issue. I have the same issue. Note 5 N9208, I can get into Recovery (TWRP) and Download mode, but can not boot. The USB connection is showing USB Device Descriptor failed. I have tried 5 different cables and Windows 7/10 Ubuntu and cant get the phone to show up on the PC. I also have changed the USB port of the phone. Any insight would be helpful.

musab_bari said:
Were you able to fix your issue. I have the same issue. Note 5 N9208, I can get into Recovery (TWRP) and Download mode, but can not boot. The USB connection is showing USB Device Descriptor failed. I have tried 5 different cables and Windows 7/10 Ubuntu and cant get the phone to show up on the PC. I also have changed the USB port of the phone. Any insight would be helpful.
Click to expand...
Click to collapse
I ended up trying to replace the port and accidentally cut the ribbon for the LCD screen. Ended up getting a new phone.