Database Develop

Dead

I let my phone battery die, and now I can't turn it on.
Usually I get a red light which goes when the battery is in if its charging.
Sometimes I get a red light even when the battery is in and its charging.
If I do a soft reset, sometimes I get a flashing red light on the sides but then nothing.
I managed to get it back briefly by doing all manner of hard resets and soft resets, and taking the battery out and putting it back in over and over again for about half an hour...
Then I left it charging for half an hour or so and carelessly allowed the battery to die again because I needed to take it with me somewhere - so the same thing has happened again.
I left it charging overnight but I'm not having any luck with it this morning... any help would be much appreciated.

yeah similar problem here. my phone warned me the battery was low... i ignored the warning and used it until it died completely. then it wouldn't turn on. it was late so i just plugged it into the wall charger that came with the phone. i dont think it charged cause in the morning it was still flat. if anything i think having it connected to the charger while not charging drained the last a few drops of juice out of it. had a number of confusing red lights coming up in different spots at different times.
i read on here some guy managed to charge it by getting 3 AA batteries and connecting them directly to the battery for a couple of minuets. i did this and managed to turn the phone on! hoooray!
it had 1% and died in less than a couple of minuets even though i had it on the charger. tried the 3 AA battery trick again but to no avail. i think my battery is dead.
i'm pretty certain i will need to get a new one. i hope you are able to get yours working without buying a new battery.
im really annoyed the Sony Erricson batteries work out to be close to $100 AU. i would prefer to get a legit one... but does anyone have any experience with unofficial batteries? are they any good?

Sorry you're in the same boat... Ericsson really should have made this phone so that it can run out of battery.
Interesting - tell me more about the 3 AA battery trick!

sounds like the cells in your battery isnt balancing hence its dying...think you'll need to buy another one / or at least try another one to make sure it is and not the phone...

Hmmm... I fiddled and pressed buttons and took out the charger and put it in, and then kept pressing the on button while I was doing something else...
Suddenly it made the click noise, but it's not back yet.
It seems to have crashed on the 'Sony Ericsson' start up screen with the green logo.
I don't know if it's charging or not, so I'm not sure whether to turn it off to try again (at the risk of losing the battery), or leave it to charge as it is before I turn it off and can't start it again....
At least it's progress

There are a couple vof threads with many solutions. Look for them, they are very useful.

Yeah I've found a few - Thanks... just nothing they mentioned has worked yet
I think the problem I have may be a slightly different now anyway...
Now, if I unplug it I can't turn it on, but if it's plugged into my computer cable I can get it (every time - after about 3 minutes) to go to the Sony Ericsson loading screen but no further (as if there is no hard reset file for it to load). I can do that by plugging it in, then doing a soft reset (which produces flashing lights on the side) then holding on until it clicks (usually trying that a few times). When it clicks the lights on the side flash and it looks like it charges for a second before the lights go off and its just hte loading screen. I left it for 5 minutes and it turned off completely. Nothing happens if it's plugged into the wall cable at all.
Have you any idea how I might be able be get something to load after the loading screen?... Or any thoughts as to whether you think it's likely to be charging when its on that screen?
Thanks

Hmm... It seems you have a software problem as well.
Here is what I would do: get another battery (fully charged) and try one of these hard reset methods:
http://forum.xda-developers.com/showthread.php?t=437607
Something should work...

Sweet - I managed to get the hard reset screen to ask me the question about going back to factory defaults... after that the lights on the side are coming on to show its charging....
I guess there's a chance that when the battery is charged it'll have the juice to get past the loading screen... I hope anyway.

Wow this title gave me a heart attack almost
i thought someone is dead

plz i need help
hello good day plz i neesd to flash my htc p3600 and sony ericcson cybershot i need a software i can use to flash them plz help me any body that has an idea

just ordered a 1800mAh mugen power replacement battery. should be here in about a week my old SE k800i will be getting a bit of a work out in the mean time.
i think this break from unnecessary technology which I'm far too attached to will do me good. I'm far too materialistic.
hope you manage to get your battery going again!

Wont Power On

I am looking at trading for a Bionic, however it has a problem. The guy I might trade says it wont turn on for him. If he plugs it into USB it will get a white LED, cant remember if he said it blinks or not.
I am quite familiar with modding phones as I have a Fascinate running 4.0. As such I have a lot of software. Any help or advice would be great. Thanks.

Anyone have any ideas.

jaed.43725 said:
Anyone have any ideas.
Click to expand...
Click to collapse
Yeah its Superbricked(battery dead, AND Stuck on "Fastboot Flash Failure" or some other "Failure". All you need is a new battery and Follow These Steps to get to stock. There is another way to charge a battery.
1. Get a spare USB Cord.
2. Cut and strip the end down(the end you stick in the phone)
3. Strip it. Give it at least 2 inches.
4. There are 4 wires. Black, Red, Green and White. Ignore the Green and White and strip the plastic off the Red & Black until its just the wires.
5. On the back of the battery there is a "+" and a " - ". Black is negative. Red is positive.
6. Connect wires accordingly. Use the OUTSIDE slots not the middle.
7. connect USB Cord to computer or wall charger and let it charge.
I HAVE DONE THIS TO CHARGE MY BATTERY IT WORKS. I did fold the wires a little to make it stick(more like jam it in here) and used a fingernail to push it to those two sides in each slot(you'll see what I'm talking about when you look at the battery).
YouTube link.
PS: Don't leave it on there for an extened amount of time(the longest I had mine on was about an hour because you will need some juice to flash to a stock rom).

So my situation is a bit different. I have a Bionic completely stock, just performed a factory reset via the menu options on the phone. It was on and working with the set up screen. It was not active and therefore couldn't go past the setup screen.
Now, my 6 yr old nephew took the phone. Had it for a couple of days, took it to school but not important, when i got the phone back it would not turn on. I figured it was a dead battery. So i plugged it in an left it for a few hours while i was at work. When i got home, it would not turn on. When i plug the phone into a charger that I verified per another phone works nothing happens. When I take the battery out of the phone and plug into my computer the led light comes on and is solid. But phone will still not come on, i even try to hold down both volume buttons and the power button at the same time.
So is my device bricked as well? And how could this have happened? Do i have to purchase a brand new battery or can I use the charging trick on my current battery?
Thank you for the help in advance!

Dead Screen or Nearly Dead Battery Issues

Okay, first thing to mention is that I have searched for information on my issue and while I have found (and tried) solutions that approach my goof, I need to post this:
Last night I finished reading from Kindle app, hit the power button to shut off the screen and laid it down. I know I should have plugged it to recharge but too late now. I am running CM nightly from 07172012, so I know I didn't download the nightly CM battery issue versions.
This morning the screen will not light up; I have tried charging it, hard reset with power and home screen buttons for 15-20 seconds (and longer), and nothing works. My concern is that the screen is dead. I connected the touchpad to my laptop and I get the connection sound from the laptop; it sees the TP but does not accept it as a portable storage device. Device Manager lists it as: QHSUSB_DLOAD with driver(s) not loaded.
When I try the volume rocker button I do not hear the small audible ping as volume goes up or down. Of course, with the resets, who knows where I am in the OS (or even if it is WebOS or Android).
I really didn't want to be a noob and post this, but I need some advice from the brethren here on XDA. Thanks in advance.

It seems to me that it's not even booting if your getting that strange device in device manager. Try the webos recovery tool from hp. It may help. Although it will wipe android off.
Sent from my SGH-I777 using xda app-developers app

my son-in-law is in the same boat. Nothing he does wakes it up. I believe there are tp's out there with this hardware issue. I let my tp battery drain completely. It powers down around 4% battery. I place it on the touchstone, it charges backup and boots into moboot, then webos. I've done this twice. no problems. If it's under warranty still, send it in.

If you have a touchstone charger put it on that and leave it for a couple of hours and it Will come back to life.
See this article by Reverend Kyle http://www.reverendkyle.com/index.php/articles/146-hp-touchpad-charging-issues-solution
I hope this helps.

I've had multiple instances of black screen of death failure.
The latest one I had, I was able to restore by using a standard USB to micro USB cable (and recently NOT the HP OEM cable) to connect to the computer I usually use to sync or use HP web doctor with.
Same symtpom as the OP, get the three dings when connecting the touchpad to the computer, no responses and the QHUSB driver load error. HP charger wouldn't chage it, touchstone would not charge it.
Anyhow, I left it connected for a few hours to charge connected to my PC. Then, I disconnected from the PC using the large USB connector and reconnected. Whamo, got to the bootloader.
I believe what happened was I trickle charged the touchpad enough to get the touchpad to boot.
You can try the various hard boot keypresses too, but wait for a few hours while trying to trickle charge the touchpad via the computer USB.

Update
Okay, so I followed the old rule of doing the simple (and/or free) solutions first and then move on.
1) I set the touchpad on the touchstone for several hours yesterday - no luck
2) I connected the touchpad to my pc through the USB and let it charge - no luck
3) I let it be plugged into the standard charging plug all night - no luck
4) I prayed to the great old god Cthulhu - no luck
My only option remaining is to use WebOS Doctor. One question on that: in all the literature I have read thus far (and perhaps I am mistaken), I need to be able to get the TP into USB mode to download the corrections/reboot back into WebOS. Is that right or can I expect that when the doctor sees the mangled mess of an OS through the USB connection, it will know what to do?
Again, as always that for the previous posts and for the support.

mnachazel said:
Okay, so I followed the old rule of doing the simple (and/or free) solutions first and then move on.
1) I set the touchpad on the touchstone for several hours yesterday - no luck
2) I connected the touchpad to my pc through the USB and let it charge - no luck
3) I let it be plugged into the standard charging plug all night - no luck
4) I prayed to the great old god Cthulhu - no luck
My only option remaining is to use WebOS Doctor. One question on that: in all the literature I have read thus far (and perhaps I am mistaken), I need to be able to get the TP into USB mode to download the corrections/reboot back into WebOS. Is that right or can I expect that when the doctor sees the mangled mess of an OS through the USB connection, it will know what to do?
Again, as always that for the previous posts and for the support.
Click to expand...
Click to collapse
Another piece of black magic that worked for me and is worth a try as it is free. Connect Touchpad to standard HP brick charger plugged into power outlet. Unplug cable from charger, count to 5, plug it back in, count to 5, take it back out. Repeat the cycle until you get bored or until you get a red charging symbol. If you get the latter then let it charge up normally and you are back in business. The theory behind this method is that it takes a few seconds on plugging in for the circuits to realise they "shouldn't be charging" and this allows a little bit of charging to take place on each insertion. Repeat enough times and you get enough to kick start the proper charging. In my case about 20 times did the trick.
As I didn't want to get into this situation again I then set up a Tasker process to power down th eTouchpad if the battey charge dropped below 8% and I've been OK since.

RIP Touchpad / EOT
Well, I had to wait a day to get my hands on a WinXP laptop; I upgraded my Dell to Win8 about 3 months ago and WebOS Doctor does not play well with Win8.
While that time passed, the touchpad finally gave up the ghost. There is no power left in the TP. When I run WebOS Doc the laptop cannot see the TP connecting via USB. I also checked by connecting the TB to the Dell, since it would at least see the device. Not any more.
My thanks again to those that responded. I did try the plug in, plug out with 5 second waits between, just in case. You never know. However, after 50+ attempts I had to call it a no-go.

does your home button light come on at all? Are you able to see moboot bootloader at all or are you able to start the tablet in webos recovery mode by holding the vol key while powering it on? are you able to ./adb connect? Also I've never had much luck with the resest method youre using, holding down the power and home key, I always hold down the power key and press the home key 15 times, when I get hard freezes and lockups, it's always worked.

Mine is in the same boat for a couple of months, removed battery and charged. Boot loader is borked I get only get a qualcomm usb device but nothing thats of any use for webos doctor or qualcomm tools. We'll have to wait until someone figures out jtag or how to replace the bootloader with qualcomm tools. I'm amazed with the number of touchpads out there that something hasn't leaked from hp to fix it. Anyone got friend in hp or qualcomm :angel:

OP Update
Well, I thought this was a dead issue but here is the latest.
After wallowing it a pit of despair the likes of which can only be described as wretched, (I even coveted my wife's TP up close, almost giving into temptation and swapping decals to reverse ownership) I looked outside of XDA and did general Google searches and happened upon this site:
http://forums.webosnation.com/hp-touchpad/299256-dead-touchpad.html
After reading a bit I realized that the touchstone may be able to recharge the dead battery even though fully drained. I began the quest that Friday morning the 24th of August, after verifying that my Dell laptop did not see the TP when plugged in via the USB cable.
I just did a quick check and the laptop now "sees" the TP when connected. Still no luck on booting into Moboot or the USB icon screen - neither Power and Volume Up or Power and Home buttons achieve anything. But I am glad to see that the touchstone has placed enough charge into the battery that the laptop is aware of the TP when connected.
I believe that given a few more days on the touchstone I should be able to boot into moboot.
@ haxin - I have nothing. Not a single light from the Home button - my only evidence that there is SOMETHING going on is when I connect the TP to the laptop and get my connection "sound". Again, I have high hopes that the touchstone will get me where I am going, albeit at a snails pace.
@ paddy - Yeah, I hope that when (if) I get to a lit screen, I am able to move past where you are at. My big concern is that I am toast even with a semi charged or fully charged battery from the touchstone.
I will update later on. Again, thanks to all for the input and probing questions. You have made me think harder and work a bit longer on this project.

OP Update - 31 August
After 7 days on the touchstone, the touchpad is currently showing the low battery charge icon; I have now plugged it into the A/C adapter.
Each morning I have picked up the TP, held down the power button and held the home button for 15+ seconds. Today it worked, turning on the screen for the first time in a week and letting me see the low battery image.
In my quest to resolve this issue, I have read so many variations on what buttons to hold and how long to hold them that after awhile you end up considering the possibility that SOME of the button options are not correct. That the operator has booted their TP up, but they misconstrued the actual solution; how else can you explain the idea that HP built so many different button combinations and hold times to boot a TP from a nearly or fully dead battery state?
Anyway, I will continue to post updates until my beloved TP is back to running CM9.
And to all those who gave their TP up because the battery got too low; find a touchstone or other "trickle" charger solution, connect and let it sit for a week or so.
Thanks!

Glad the Touchstone worked for you , don't know why it has taken so long to charge but when your up an running properly Llama is a good app to install as
A:You can set alarms for when the battery gets to a certain level/levels
B:Have it shut down when the battery gets to a certain level.
I use 20% for an alarm and 10% to shut down which allows me to sleep easy and not worry if someone else is using it . .

I am up and running. I most definitely will load that app on my TP, plus my wife's and a coworker who bought a TP because of mine.
I don't know either why it took so long; I am just glad it worked and I have it back. I am on it right now.
Thanks again to all who provided feedback and guidance. This is why I love XDA.
Sent from my HP Touchpad using xda app-developers app

HP Touchpad sleeping and will not turn on
Just a note to those HP tablet owners who experience the Black screen of death or sleep of death.
I am the proud owner of 4 HP tablets and two of them so far have had the black screen of death. I have read forum after forum trying to get answers to this problem. There was only one posting that has made cense to me. Someone posted that the tablets symptoms are very much like when the Phones use to go to sleep. The solution was to disconnect the battery for a few minutes then plug it back in. Then simply hit the hold the power button down to turn on the tablet.
The problem is taking the TP apart. There is a video on youtube on how to disassemble the tp. It is a little annoying that you have to go to such lengths to reset the hardware but HP will charge you 250 dollars to fix the problem. After you watch the video on how to open the TP, remove the 3 little screws holding the battery. Now slowly pry the battery up, they use double sided tape to hold it in place along with the screws. Wiggle the battery side to side and try to disconnect the battery connector. This can be done without removing the boards in the TP. Wait 1 min then try to replace the connector in the socket. It is on the underside of a board so when you have it in place use something to make sure it is tight. Plug the charger in to the USB cable. Without closing up the unit hold the tablet power button in until you get the battery charging symbol on the display. Let the unit charge while it is still disassembled. Just in case you have a problem. Once everything is operating disconnect to charger and replace the battery screws, now snap everything together.
This was the only way I was able to fix two of my four TP's. I am sure I will have to do this again because my kids always let the tablets go dead and they don't pay attention when placing them on the Stone for charging. If the tablet is not properly placed on the stone the tablet will not charge.
Hope this helps.
This by far is the best tablet for the money anywhere.

msousa1 said:
Just a note to those HP tablet owners who experience the Black screen of death or sleep of death.
The solution was to disconnect the battery for a few minutes then plug it back in. Then simply hit the hold the power button down to turn on the tablet.
The problem is taking the TP apart. There is a video on youtube on how to disassemble the tp. It is a little annoying that you have to go to such lengths to reset the hardware but HP will charge you 250 dollars to fix the problem. After you watch the video on how to open the TP, remove the 3 little screws holding the battery. Now slowly pry the battery up, they use double sided tape to hold it in place along with the screws. Wiggle the battery side to side and try to disconnect the battery connector.
Click to expand...
Click to collapse
I realise this is an old thread, but I recently had a reoccurrence of the black screen of death issue and thought given the number of touchpads still out in the wild, I would share my experience on the off-chance it may help somebody.
My first experience of the black screen issue was a few months after having my touchpad (many years ago). The screen just went black and no combination of holding the reset keys for any period of time would restart the unit. I had suffered lock-ups before and found the reset combination to be successful, but this time none of that worked and I had effectively what appeared to be a dead unit.
Having contacted HP, I returned the unit under warranty and a unit was returned working. I say “a unit” as I was never quite sure if it was the same unit or a refurbed unit, but to be honest given the speed the units went out of stock during the fire sale, I was just glad to have a working unit again.
Well this week after several years of use including the installation of Android, the black screen occurred again. As before, no combination of the keys / holding for a period of time / pressing them a number of times etc had any effect. The unit was three quarters charged and I was using it up till the point the screen went black. :crying:
Given that the unit has no warranty and it was “dead” anyway, I decided to take it apart. Despite watching YouTube videos, this appeared to be more troublesome than I thought, but eventually I was in. Interestingly, the backlight on the screen was still lit, suggesting the unit was still powered. I did consider disconnecting the battery, having removed the screws as per the previous poster, but mine seemed to be well and truly stuck down and I felt I may damage it prying it away from the base.
However, looking around inside the unit, I spotted what was clearly a surface mounted switch that faced upwards towards the back of the screen. Out of interest, I pressed on this switch with my finger nail and my unit powered off (shown by the backlight turning off). I then pressed the normal power switch and the unit powered up as normal. I have attached a photo of the switch which resides close to the popout tab with serial numbers on that can be found on the right hand side of the unit.
It does appear strange that HP put this “reset” button inside the unit, facing inwards rather than outwards where a small hole in the back of the case could be used to press it. So if you do get to the opening the case stage, consider this as an alternative to prying the battery loose. Also if somebody can work out a way to make the button accessible from outside the case it might be a useful modification.

JoeG90 said:
<.......................................>
However, looking around inside the unit, I spotted what was clearly a surface mounted switch that faced upwards towards the back of the screen. Out of interest, I pressed on this switch with my finger nail and my unit powered off (shown by the backlight turning off). I then pressed the normal power switch and the unit powered up as normal. I have attached a photo of the switch which resides close to the popout tab with serial numbers on that can be found on the right hand side of the unit.
It does appear strange that HP put this “reset” button inside the unit, facing inwards rather than outwards where a small hole in the back of the case could be used to press it. So if you do get to the opening the case stage, consider this as an alternative to prying the battery loose. Also if somebody can work out a way to make the button accessible from outside the case it might be a useful modification.
Click to expand...
Click to collapse
Oh I was so keen when I came across this post. A Reset Button! How great would that be?
Tried it, unfortunately it did not resurrect my dead as a doorstop TP. I was so hoping...
I just put a 'new' EBay battery in it a couple of days ago and tried trickle charging with a 1000mA charger for 24hrs. No joy there either.
All I get when I plug it into the PC is that it shows up as a "QDLoader 9008" (QHSUB_DLOAD driver) .
No flicker of life or light whats so ever...
_mr

middle_road said:
Oh I was so keen when I came across this post. A Reset Button! How great would that be?
Tried it, unfortunately it did not resurrect my dead as a doorstop TP. I was so hoping...
I just put a 'new' EBay battery in it a couple of days ago and tried trickle charging with a 1000mA charger for 24hrs. No joy there either.
All I get when I plug it into the PC is that it shows up as a "QDLoader 9008" (QHSUB_DLOAD driver) .
No flicker of life or light whats so ever...
_mr
Click to expand...
Click to collapse
Try to borrow a Touchstone conductive charger if you can. It's the only thing that has worked for me when it has totally drained down.
All the best.

sstar said:
Try to borrow a Touchstone conductive charger if you can. It's the only thing that has worked for me when it has totally drained down.
All the best.
Click to expand...
Click to collapse
That's what I was thinking - no joy there either... It is not even showing signs of getting the least bit warm.
I keep thinking and hoping that there is some way to resurrect this one but I may be wrong...
It's currently trickling on a 1000mA charger. Tomorrow I'm going to try the Touchstone behind it.
If that doesn't start something then I'm going to yank the new battery and along with the old battery charge them like an RC device.
(if I can ascertain the proper way to do that --- )
_mr

After several days on the trickle, still no life.
Took it apart at lunch and with the battery still connected to mobo it is showing 3.1V across the red/black. So I figure the battery
is good. Looks like the mobo is gone.
Not sure what else to try.
_mr

[Q] [Help Thread] Nook HD not booting at all

I recently went on a 3 month trip. Before I left, my nook was working perfectly fine, when i got back, it didn't work at all. It's not dead because i left it plugged in overnight but it still didn't turn on. when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all. I can't get to recovery either.
This is a Nook HD, I believe it had CM11.
:crying:
Can this be fixed
or should i plan it's funeral

Same here
The same has happened to me. Screen doesn't turn on, but there is power, I can play it into my laptop and something is there, just not enough.
Good excuse for a new tablet!

It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).

tambourineman86 said:
It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).
Click to expand...
Click to collapse
If would be fab if you could fix. Seems to be a common issue

I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.

tambourineman86 said:
I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.
Click to expand...
Click to collapse
Not sure we have the same problem. My screen doesn't come on at all, I don't get a battery depleted icon, no matter how long I hold in the power button. The only sign of life I get is when it's plugged in, when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.

YMMV. But mine was the same issue. You should be able to get the icon by holding the power button down for 5 or 6 seconds. I'd say just eff with it until that icon appears. Try different button combinations. I used power and home trying to get the icon to show.

developerbuzz said:
when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.
Click to expand...
Click to collapse
Anyway... since people are continually running into this kind of issue...
Give or take 21 seconds after turning orange it turns green during actual boot cycle into rom
Give or take 10 seconds after turning orange is cwm internal recovery.
After about 10 seconds the charging screen image disappears.
The charging screen image once finally no longer may not show up again until full power off/on (holding power button > 10 seconds or full battery discharge). Unplugging and plugging back in does nothing except making the device look bricked if there's too much light shining on it.
Device may not automatically leave the above state under a specific situation(s). May still need manual full power off/on.
Guessing 10 seconds could also be something else during the early/late boot process or other. The light changing color though should indicate that something is indeed happening.
Light should stay green during the boot process if its completely and fully no questions asked 100%. If you go based on that than yours doesn't appear to be completely fully charged which should either mean its turning on and using battery or not charging correctly.
The light turning off is curious. The device could be shutting off. If light comes back on a moment later then the device has rebooted. if the light stays off = n/a.
If its booting into recovery then the device would be available via adb. At that point it could be further evaluated.
On the off chance the screen was damaged it should boot and usb should be available via computer as well as adb.
If not then its probably toast unless its simply not getting a good enough current causing mislead battery stats and/or not enough energy to get to charging screen (bad wall power adapter in use, damaged power cable - though could be bad battery, defect, damage or whatever). OR there's some major error on behalf of the user happening (think should have tried that in the morning not while 1/2 asleep or came home from long trip and forget how that works).
Maybe the only other things are the emmc brick bug, was left sitting in the sun or heat or ocean air or other physical damage/defect even to the power port as well.
Or maybe it was mad that you left it. Shouldn't have hurt its feelings you know. At least its not crying battery acid on you.
That should just about cover everything except for the things not mentioned. Since its your device, you decide what happened.
Its complicated so anyone see any improvements, clarifications, or mistakes? Please put it in a post.

Jsorren said:
when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all.
Click to expand...
Click to collapse
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.

sandsofmyst said:
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.
Click to expand...
Click to collapse
I actually ended up fixing it yesterday!! I haven't touched it in about 3 months, and I was planning on just throwing it out getting rid of it some how. For the heck of it, I decided to plug it in, assuming that it was gonna go through the same process. But this time it went from green to amber, but it never went off. So I pressed the power button and the battery icon appeared. This was a really good sign. So I left plugged in for about 5 to 10 minutes then tried to power on.:fingers-crossed: As soon as I saw that '' Nook" boot up screen, my heart stopped. It booted up perfectly and I almost blew up from excitement :victory:. So I then flashed the stock firmware back onto it, so this would never happen again.
I guess the battery had to be completely depleted or just had to cool down. Idk but either way this was one heck of a miracle
So I recommend for anyone having this problem to just leave it off and don't mess with it. I wouldn't say for 3 months like I did but maybe test it each week or wait a month if you have good patience

Wow. Man, that's awesome! Glad you posted that update on it. Thought if you had posted an update it would be the opposite as in trashed it
Actually, I guess only you could answer if you had also moved/unplugged the power cable from the wall adapter or put it into a different wall adapter, etc. Thinking there could have been a difference there.
These modern day devices are so finicky, guess anything is possible. Like you say, maybe sitting without power is another answer.

From some experimentation I have etermined that your power adapter (that plugs into the outlet) is the issue. It does not like to be leaft plugged in indefinately. It will continually use power even when the nook is not plugged in.
Also, if you use a differnt adapter you will have the same problem unless it is also of the exact same voltage and amps.

Fix for broken power button (Mi 9 Pro, but will probably work for Mi 9)

Maybe not the right sub-forum for this, but for some reason I show as not logged in on the Guides sub-forum.....
Long story short, I removed the shattered back of my phone for replacement, and in the process it appears I did something that broke the power and volume buttons. I don't know what broke, it all looks good, but I used a blade to lift the cover and in retrospect, I think heat and a suction cup would have been better.
I tried rebooting prior to installing the new rear cover, and lucky I did because I needed access to finally fix it. The buttons were completely dead, nothing worked, but if I plugged in power, it started charging, so I knew the battery and screen were still good. From adb, the device was there but unauthorized, so I was unable to boot that way (I've since rebooted and turned on USB debugging, but evidently it uses the vendor keys still when in recharge mode, and it still showed unauthorized).
None of the local shops were any help, I suspected that if I could get the boot sequence to start all would be good, and this turned out to be the case, but they were all clueless about anything other than changing the battery or the screen.
Anyway, onto the solution. The first time I got it to boot, I simply disconnected the battery, then plugged in the power using the Xiaomi charger, it wouldn't boot at all from USB power, it would only charge. As soon as I plugged it in, the power sequence started and the phone booted and ran fine. I pushed the battery connector back into place and all was good, except the problem of what happens if I power it off.
I went to developer options, checked USB debugging, and powered off, confident that even if I still couldn't see it in charging mode, I'd at least be able to manually power it on after disconnecting the battery. Well, of course, the second time it didn't work. ADB was still unauthorized, and the battery disconnection trick didn't work, it started to boot but then appeared to lose power and the screen faded. This gave me a clue that it might be possible to use the wireless charging to get it to boot, but the problem with that was that it wouldn't wirelessly charge with the battery disconnected. In the end, what worked was to loosely hold the battery connector with my finger over the contacts, while holding the phone against the wireless charger (I have the Xiaomi 65W wireless charger), in this state the battery reads 15% even though it's full, but the phone boots. I then pushed down to fully connect the battery, at which point it read 100% and was booted. It's super-fiddly to hold it all in the right position, but perseverance pays off. If you lose the connection to the battery completely at any point, the phone simply dies.
To get to the battery connection on the Mi 9 Pro, lift the wireless pad, at the top right corner of the battery you'll see a short flat black cable that runs towards the centre of the battery and then up to connect to the motherboard. Lift up on that connector with something thin to pop it off. When rebooting, hold your index finger on the connector with enough pressure to make a contact without fully reconnecting it, while holding the wireless pad against the charger. Why the hell this works I have no idea, but it does.
To operate the volume/power, just download widgets. It would be nice to have a physical volume button, but doing it from the screen works.
This was a life-saver for me because I friggin' love this phone. I have the 12/512 model, and it's so good I've finally stopped fiddling with ROMS because it just works perfectly. Unfortunately, it took me a week to figure this out, and I ordered a Mi 11 Pro in the meantime!
If anyone has any good ideas about an easier way for me to reboot in case it ever powers off (a simple reboot is fine), I'm all ears. I'm currently looking at having to remove the rear cover again and go through the whole rigmarole if it ever powers off.