Database Develop

Orzly Tempered Glass Screen Protector [Small review]

The Orzly Tempered Glass Screen Protector. I used 3 of them on my 1+1 and they did their job perfectly, not a scratch on the screen even when I sometimes thought it was done for. So after ordering my 1+3 i first bought the tempered glass screen protector from Oneplus. Huge mistake. Hands down the worst screen protector i used so far. So almost immediately i ordered myself a trusted Orzly screen protector.
Installation:
Installation of the screen protector was quick and easy. I guess the procedure is about the same for every screen protector out there but still.. The only problem is that even i wiped the screen clean with the cloth etc. But still i managed to get a spec of dust on the screen which really annoys me. I guess i'll just buy another one
Conclusion:
Great screen protector, does the job perfectly. I hope i don't need to replace it any time soon.
Pictures:
As you can see on the picture below, the screen protector from Oneplus isn't all that good...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
However the Orzly one:

thanks for the review but before people run out to buy one based on this review, a few things i feel should be mentioned:
1) this Orzly protector does NOT work with a lot of cases. if you have a case that covers the sides but doesn't go over the glass, it will push and lift the Orzly. if you do have a case that fits snug, it will push in the glass and create weird color marks.
2) the protector has dots on it that are clearly visible in direct sunlight and quite frankly, make the screen look like crap.
3) the protector is a smudge/fingerprint magnet!!!
4) because it doesn't quite stick to the screen, unless the sides are fully covered by a case, you will get dust inside.
5) i did notice a slight touch response degradation but its not major.
my conclusion: Orzly dropped the ball on this one. i had their protector on the One and the Two and they were incredible but the one for the Three is a mess and i will be asking for my money back.

I can only confirm it. I'm very disappointed with Orzly tgsp. It doesn't work with orzly flex case. Matrix dots are very annoying, so far it's the worst screen protector I purchased.
Wysłane ze zmywarki

Rattles said:
thanks for the review but before people run out to buy one based on this review, a few things i feel should be mentioned:
1) this Orzly protector does NOT work with a lot of cases. if you have a case that covers the sides but doesn't go over the glass, it will push and lift the Orzly. if you do have a case that fits snug, it will push in the glass and create weird color marks.
2) the protector has dots on it that are clearly visible in direct sunlight and quite frankly, make the screen look like crap.
3) the protector is a smudge/fingerprint magnet!!!
4) because it doesn't quite stick to the screen, unless the sides are fully covered by a case, you will get dust inside.
5) i did notice a slight touch response degradation but its not major.
my conclusion: Orzly dropped the ball on this one. i had their protector on the One and the Two and they were incredible but the one for the Three is a mess and i will be asking for my money back.
Click to expand...
Click to collapse
Completely agree Rattles, this screen protector doesn't fit with Orzly's own Grip Pro case. For me the touch response degradation was so bad, I removed the screen protector after less than 24 hours with it fitted and fitted it to the inside of my bin.
Personally, I think that this screen protector is utter trash.

I second the negative experience with the Orzly TGSP, which is quite a bummer. I had very good experience with their TGSP on previous devices, but I guess the curved screen made them make a bad deciscion to go with the black bordered one.

Rattles said:
2) the protector has dots on it that are clearly visible in direct sunlight and quite frankly, make the screen look like crap.
3) the protector is a smudge/fingerprint magnet!!!
4) because it doesn't quite stick to the screen, unless the sides are fully covered by a case, you will get dust inside.
5) i did notice a slight touch response degradation but its not major.
Click to expand...
Click to collapse
I am pretty happy with the Orzly which I use with a sandstone case.
2) Dots are only visible under certain circumstances, but it is rare, in my case 99% of the time not visible. I already forgot about them.
3) Agree, it is a fingerprint magnet. But also easier to clean than the original screen protector.
5) Didn't notice any touch response degradation and must state that thanks to a more slippery surface the fingers slide better which for me is a big plus.

Although it fits perfect and the dot matrix doesn't bother me but dust entered the screen protector after a week even though I was using a case.

Very disappointed with orzly. Not 2.5d at all. Glass is bigger than screen and there are a lot of dust in the gap. Dots are visible quite often. Doesn't stick well.. Hate it.

Bought and discarded the protector after one day of use. For all the points mentioned by many above. Waste of money.
Sent from my ONEPLUS A3003 using Tapatalk

robthebass said:
I am pretty happy with the Orzly which I use with a sandstone case.
2) Dots are only visible under certain circumstances, but it is rare, in my case 99% of the time not visible. I already forgot about them.
3) Agree, it is a fingerprint magnet. But also easier to clean than the original screen protector.
5) Didn't notice any touch response degradation and must state that thanks to a more slippery surface the fingers slide better which for me is a big plus.
Click to expand...
Click to collapse
ushpiy said:
Although it fits perfect and the dot matrix doesn't bother me but dust entered the screen protector after a week even though I was using a case.
Click to expand...
Click to collapse
Yes, i agree. The dots are only visible in direct sunlight. That still so many have bad experience with this tgsp. I really like it!

Just to add one more negative thing: the Protector is very reflective (compared to other tempered glass protectors and stock Display). Hence outdoor usage is limited.
Gesendet von meinem ONEPLUS A3003 mit Tapatalk

I also have this one and I'm super disappointed.
I mean, why don't they just make it translucent? And why is there no glue on the glass? It lifts off even without a case...
Also the cutouts aren't perfect, while the camera and speaker ones fit perfectly I only see half of the buttons. And those fingerprints!
Really, even the pre-applied protector from OnePlus was better.

I can confirm all these flaws. Anyone got a recommendation for a good one? The official oneplus one is back in stores, so I maybe just end up buying this.

I threw it away as well. It was worse than the official one tbh, at least the official one doesn't fall off all the time...
Sent from my ONEPLUS A3003 using Tapatalk

FYI: Complained about the garbage quality through Amazon and got my money back.
Time to find a better glass protector now.

i got a casebase protector but havent removed the protector that comes with it, should i try the casebase or is everyone going back to standard protectors since these full coverage ones arent cutting it?

merewood bebox said:
i got a casebase protector but havent removed the protector that comes with it, should i try the casebase or is everyone going back to standard protectors since these full coverage ones arent cutting it?
Click to expand...
Click to collapse
As far as I can tell , the Case base is identical to Orzly so honestly, I would just keep the one that came with the phone and send it back.

Rattles said:
As far as I can tell , the Case base is identical to Orzly so honestly, I would just keep the one that came with the phone and send it back.
Click to expand...
Click to collapse
Alight so what you planning to use now, there's not much Choce for this phone now that I i think about it

Thank you
You just saved me man, I was about to order after reading the post.
Rattles said:
thanks for the review but before people run out to buy one based on this review, a few things i feel should be mentioned:
1) this Orzly protector does NOT work with a lot of cases. if you have a case that covers the sides but doesn't go over the glass, it will push and lift the Orzly. if you do have a case that fits snug, it will push in the glass and create weird color marks.
2) the protector has dots on it that are clearly visible in direct sunlight and quite frankly, make the screen look like crap.
3) the protector is a smudge/fingerprint magnet!!!
4) because it doesn't quite stick to the screen, unless the sides are fully covered by a case, you will get dust inside.
5) i did notice a slight touch response degradation but its not major.
my conclusion: Orzly dropped the ball on this one. i had their protector on the One and the Two and they were incredible but the one for the Three is a mess and i will be asking for my money back.
Click to expand...
Click to collapse

I installed mine and I like it. I'm pretty ocd about acreen protectors too...no gap under acreen, and I use the oneplus sandstone snap case and it doesn't touch the protector. Only fault is the dang rate it picks up fingerprints. I can see the dots underneath, but only in sunlight...that not an issue at all. I tried about 3 different ones odd of Amazon before I left this one on.
Sent from my ONEPLUS A3000 using XDA-Developers mobile app

OnePlus 3 Tempered Glass suggestion

I live in desert area and there literally unlimited amount of sand everywhere!
can anyone suggest me a good tempered glass? I have checked some on amazon but reviews says they suck!

I have had two different TGSP now and they both End up the same. Does not stick to the edges due to the curved screen. But mine does not Collect lint at all even though it does not adhere to the screen.
I have not tested orzly or similar but they seem to work bad with cases so.. heard though that orzly were coming with a new model soon that is slimmer.

Tried a few, all junk.. Until i bought the orzly brand. The one with the black tinted frame.
I could be lucky but It fits perfectly, stick securely to the screen and is now holding for 10days of very heavy use without a scratch or bubble or anything.! Can be used with the original sandstone cover and does cover the whole screen!

w3bureau said:
Tried a few, all junk.. Until i bought the orzly brand. The one with the black tinted frame.
I could be lucky but It fits perfectly, stick securely to the screen and is now holding for 10days of very heavy use without a scratch or bubble or anything.! Can be used with the original sandstone cover and does cover the whole screen!
Click to expand...
Click to collapse
Pictures and link to the specific protector you use? Would it work with cases with a lip around the front screen?

I ordered one similar. Is it easy to apply? your general thoughts on clarity, touch, etc?

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Avoid at any cost!!!
This is why...
Regards
Goran
Sent from my ONEPLUS A3003 using XDA-Developers mobile app

I'm using Nillking 9H+Pro TGSP and I find it really REALLY nice. Little halo effect on both sides but is Silky smooth and covers a great part of the screen

lparcshinoda said:
I'm using Nillking 9H+Pro TGSP and I find it really REALLY nice. Little halo effect on both sides but is Silky smooth and covers a great part of the screen
Click to expand...
Click to collapse
Can you post pictures of it. How bad is the halo?

lparcshinoda said:
I'm using Nillking 9H+Pro TGSP and I find it really REALLY nice. Little halo effect on both sides but is Silky smooth and covers a great part of the screen
Click to expand...
Click to collapse
I think it is the best for phones with cases even though there are issues with the "Halo" and it doesn't go edge to edge. The edge to edge or full coverage tgsp pull up with cases.
Sent from my ONEPLUS A3000 using Tapatalk

Hopefully this helps for Orzly Case Compatibility:
https://youtu.be/8Je-Ug0hM3E

Clarkkent434 said:
Can you post pictures of it. How bad is the halo?
Click to expand...
Click to collapse
It depends on how you are aligning the TGSP. For my personal preference I've installed it a little more towards the left side to maintain perfect readability and on the left I can see 1.5 mm halo effect that is like some 2.D visual bending effect. With the screen on you notice a some small rainbow effect but that is the only noticeable distortion. I will send some picture later

Has anyone tried the TGSP from OnePlus? Does seem to be on the pricier side, but since it's from OP, it shouldn't have any problems with fitting at least

lparcshinoda said:
I'm using Nillking 9H+Pro TGSP and I find it really REALLY nice. Little halo effect on both sides but is Silky smooth and covers a great part of the screen
Click to expand...
Click to collapse
This is like the only quality tgsp available in my area, so can you tell me, does it fit with casings like the tudia merge? Cause I'm thinking of buying/

Using Nilkin Amazing H+ PRO. It doesn't stick all the way because of the curved screen but it doesn't colect dust in those gaps. Actually no glass for OP3 sticks to the very end. It's all transparent (no black areas), and covers the front camera.
I saw this review and went for it. Can confirm that everything in the video is true.
EDIT: Can't confirm any compatibility with cases since I don't have and don't use any.

EDIT: Got a refund, the glass started to completely come off the top of the phone, and what with covering the notification light and a bit of the front-facing camera, that was the end of it.
I put the Pleison tempered glass protector on my OP3 yesterday; it's the 'new version' screen protector found on Amazon. It's OK, it covers the screen (I've also got it in a Spigen Neo Hybrid case), but the cutout for the front-facing cam isn't exact, there's a bit of 'shadow' on the right-side of the cam when you go to take a picture/video chat/etc. It also completely blocks the notification light, which is a PITA.
The top of the protector isn't 100% adherent to the screen, there's just a tiny bit of gappage that you can feel. Also, it makes it a little less than responsive when swiping down to open up the status bar/Notification Bar, you have to make sure to press a little harder than you normally would.
There was a little 'rainbow' effect going on when I first installed it, but that went away by the end of the day. All in all it seems like one of the better protectors out there, given Amazon reviews, but I don't think any company's got it down 100% yet. I have no idea why......
---------- Post added at 09:23 AM ---------- Previous post was at 09:20 AM ----------
Tidybeer said:
i hadn't found the tempered glass could cover all the screen, so just bought this full screen protector: http://vifocal.com/tempered-glass-f...e-for-oneplus-3-oneplus-three-smartphone.html
Click to expand...
Click to collapse
Have you received it/put it on yet? If so, how do you like it?

chops650 said:
Has anyone tried the TGSP from OnePlus? Does seem to be on the pricier side, but since it's from OP, it shouldn't have any problems with fitting at least
Click to expand...
Click to collapse
Brought the OnePlus TGSP with the phone a few months ago. The glass is the same size as the film that came with the phone, so it doesn't cover edge to edge. Pretty annoying because there's about 1 mm gap on each side between the edge of the screen and the TGSP. I haven't put it on yet.
It seems like all of the TGSP leave a halo effect based on the reviews.

I am using the Orzly glass and I am not fascinated about it.
Yes it covers the whole screen, yes it is compatible with the original OnePlus Snadstone hard case.
What i don't like is that it collects a lot of fingerprints thus making the screen hellish in direct sunlight. Add this to the clearly visible dots and one of the advantages of OP3 is gone.
I am still researching for a good TGSP and might try the new one from OP.

Tidybeer said:
Has a rainbow effect after full screen cover ... but decent product installation .. .. .. fingerprint magnet.
Click to expand...
Click to collapse
Yeah, I edited my original post; in addition to the blocked notification light and partially-covered front-facing camera, it started coming off the top of the screen even more. Got a refund from Pleson.

Tempered Glass For Oneplus 3/Oneplus Three/A3000 Phone 5.5 Inch High Quality Safety Full Cover Screen Protector Full Screen
http://s.aliexpress.com/MZJZNfmU
oneplus 3 glass tempered one plus 3 full cover mofi original protective glass one plus 3 screen protector ultra thin clear film
http://s.aliexpress.com/maEbyiqe
Is everyone buyed one of this? Feedbacks seems good but someone says there is same problem.

Djalaal said:
This is like the only quality tgsp available in my area, so can you tell me, does it fit with casings like the tudia merge? Cause I'm thinking of buying/
Click to expand...
Click to collapse
it does fit with orzly tpu case and the official karbon case, so it should fit with every other case

Cases & screen protectors

Hello, any recommendation of tempered glass?
Nillkin is definitely one of best case option:
http://nillkin.org/smartphones-acce...-accessories/nillkin-xiaomi-mi-note-2-frosted
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
However no glass is available, only films. Any glass suggestions?

Mofi is good one i think.
Xiaomi Mi Note 2 glass tempered MOFi Mi Note2 glass screen protector 3D full cover Xiomi Note 2 tempered glass film 5.7 Xiami
http://www.aliexpress.com/item/32760984844/32760984844.html

The Mofi screen protector is easily the worst thing I've ever used. I had it on for about 6 hours before giving up.
I've used mofi glass screen protectors before and had no problems but this time they've done something different. Instead of the curved glass sticking to curved screen there is only some adhesive around the very edges and the home button. This leaves the portion covered the screen itself "floating". When I fitted the protector it was flush, though it didn't feel solid the way a glass protector usually feels like an extension of the original display but okay. Touches weren't being registered properly and things weren't great.
Over a couple of hours the glass flexed enough that I could hear an audible tap as the screen protector made contact with the phone.
Complete waste of time and bizarre, I've fitted mofi brand curved iPhone 7 screen protectors that adhered in the usual way, this having a band of glue around the outside did not work.
If anyone can recommend a glass screen protector for this phone that isn't held in place only around the edges I really would welcome it.

Glass
StoneTrapper said:
If anyone can recommend a glass screen protector for this phone that isn't held in place only around the edges I really would welcome it.
Click to expand...
Click to collapse
I have the same issue with the glass screen protectors too. After getting my first screen protector, I have been looking very carefully at the screen protector photos before I buy them.
It seems almost all the 3D glass screen protectors have glue only around the edges and possibly come from the same factory.
There are some PET 3D screen protectors which seem to be good, but they are just plastic.
I have an order on the way with what I hope is a proper 3D glass screen protector. I will update if it is any good.
The one I am getting is called Mocolo. I cannot post any links yet because I am new user. I messaged the seller and they said it has glue on the whole surface of the glass, if that is correct I will let you guys know.

Do not buy Mocolo one either, it is the same as all the other 3D glass screen protectors for Mi Note 2. Seems they all come from the same factory with the crappy only on edges glue.
I can't find any good ones right now.

Sorry guys to say that, forget about tempered glass. Your device has a curved screen, like S7 Edge, Note 7. I've owned a Note 7 and there was not a single good working tempered glass protector. Same story with the S7 Edge. There are only protectors having the glue on the edges. If there's nothing suitable for Samsungs blockbuster device, why should there be something for the Mi Note 2. Even for my Mi Mix, with much more less curved edges there's nothing covering the screen fully that is working. Only crap. I gave up and use it naked.

Same here:
https://www.aliexpress.com/item/For...-Full-Coverage-Print-Edge-3D/32764076840.html
poor quality. And after few weeks glass shattered on the edge

Anyone knows of a wet apply skin for mi note 2 screen protector. How is the dimensions comparative to the Galaxy S6 edge plus.
Curved glass screens are not good fit
Sent from my Mi Note 2 using Tapatalk

..

Has anyone got a reasonable soft-plastic screen protector for their note 2? I can imagine that tempered glass wouldn't work well, but there should be plastic ones that can work, right?

I've used
ZAGG InvisibleShield HD Screen Protector for Samsung Galaxy S6 Edge Plus
Was a very close fit to the device dimensions.
It's a wet install so watch a few you tube videos to see what needs done.
Other soft screen covers for that device would also work.
What DOESN'T work are the curved hard covers because they introduce a gap between screen and cover, reducing response
Sent from my SM-G955U using Tapatalk

Got the Nillkin frosted which is really nice. Only thing it's a bit more slippery than I thought it would be. But got it just today so that might improve.

for screen protector, i decide to use nano liquid screen protector, the curve design is much better using using this.., no glass, no plastic over the top. review looks like promising, but i'll gamble with reality, 1 week run without screen protector, only liquid protected, still look good

Using this 3D temperred Glass protector since yesterday: http://www.ebay.nl/itm/Full-Coverag...717177?hash=item2385dd21b9:g:FtMAAOSw3gJZMIIU
It's ok. Not too great. But considering this is sort of the only one available it's gotta do the job.
Fits good. Protects the whole screen. The surface gets dirty pretty easy, worse than the screen itself. Protector itself seems a little bit "misty" not too clear... There seems to be a little glue on the edges.
Used to have better protectors on my Samsung Note 3. But overall, it protects my screen and does the job. Hope there will be better alternatives in the future.

Did anyone try this one? http://www.ebay.nl/itm/Full-Coverage-3D-Curved-Tempered-Glass-Screen-Protector-for-Xiaomi-Mi-Note-2-Bla-/162621714306?hash=item25dd026f82:g:LeIAAOSwJhdZiKXP

Everybody here uses the Nillkin case I think.. this one: https://pt.aliexpress.com/item/case...rosted-PC-Plastic-back-cover/32769605569.html
Another one, from Lephee is a good try I guess: https://pt.aliexpress.com/item/LEPH...i-Note-2-Cover-PC-Matte-Hard/32763435273.html
The other brands I think they are ugly ..
I think I will use it without a screen protector for a month to see how it feels..
---------- Post added at 05:12 AM ---------- Previous post was at 05:08 AM ----------
fajarep said:
for screen protector, i decide to use nano liquid screen protector, the curve design is much better using using this.., no glass, no plastic over the top. review looks like promising, but i'll gamble with reality, 1 week run without screen protector, only liquid protected, still look good
Click to expand...
Click to collapse
How it feels with the touch? does that make it worse or not?
Isn't it a placebo effect? (I was wondering if that liquid is only alcohol, lol)..

Does anyone try and recommend this product? are nano screen protectors fully glued including display or just edges??
https://www.aliexpress.com/item/Xia...lgo_pvid=37f2bc3f-4b20-4cef-b881-0dd15d727cde

thedeejay said:
Has anyone got a reasonable soft-plastic screen protector for their note 2? I can imagine that tempered glass wouldn't work well, but there should be plastic ones that can work, right?
Click to expand...
Click to collapse
This one is good, but hard to apply. Ruined one before succeed.
https://www.aliexpress.com/item/2PC...reen-Protector-Soft-Film-For/32845231715.html

Can I buy an original Xiaomi Mi Note 2 cover somewhere? The one that is added to the phone.
Wysłane z mojego Mi Note 2 przy użyciu Tapatalka

bialyikar said:
Can I buy an original Xiaomi Mi Note 2 cover somewhere? The one that is added to the phone.
Wysłane z mojego Mi Note 2 przy użyciu Tapatalka
Click to expand...
Click to collapse
I wanted to buy it too , but i didn't find any....
Maybe you have more luck...

Tempered glass screen protector for Xiaomi Mi 6

Did you guys have any luck with screen protectors?
I purchased 2 on gearbest (transparent ones, not the ones with tinted bezels) and they look horrible, all the bezels and around the home button... it looks unsticked due to the slight glass curvature. I'll upload pictures once I can.

I had the same and threw them away 1 minute after installation because they didn't stick near the edges...
So I ordered these on Ali Express. They fit quite well but don't really 'stick' the same way as the thicker ones do on a perfect flat screen so there is a way dust can get under that screen protector...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Search for Nillkin screen protectors. This is the best in my opinion.
https://www.aliexpress.com/wholesal...e_id=AS_20170625020132&SearchText=mi6+nillkin

smooth_gl said:
Search for Nillkin screen protectors. This is the best in my opinion.
https://www.aliexpress.com/wholesal...e_id=AS_20170625020132&SearchText=mi6+nillkin
Click to expand...
Click to collapse
Any pictures to show what it looks like when stuck?

reb00tz said:
Any pictures to show what it looks like when stuck?
Click to expand...
Click to collapse
Here

And this one is from Cafele

smooth_gl said:
Here
Click to expand...
Click to collapse
Thanks! It appears there isn't the ugly edges because it is smaller than the curved parts, but coupled with a good "all around" bumper case, that should suffice...

i use a non brand, from Chinese, tempered glass.
but it's 3D, edge to edge, curved tempered glass, covers fully until the metal sides
it even works perfectly with a case, full protection till the edge of the case
not sure if it can be found outside my country though, since its a no brand thing
can post a pic if you guys want to see

@ ZackoFF96
Could you share a link to a shop where you bought it, please.
Thank you in advance.
+

Hi, I would love to see a pic!
Also how is the glare on it?
It seems strange that high quality screen protectors that cover the whole mi 6 screen are so hard to come by. The ones with the coloured edges are sufficient to cover up the defects around the edges but I find the glare on them terrible.

tkawa said:
@ ZackoFF96
Could you share a link to a shop where you bought it, please.
Thank you in advance.
+
Click to expand...
Click to collapse
ismael94 said:
Hi, I would love to see a pic!
Also how is the glare on it?
It seems strange that high quality screen protectors that cover the whole mi 6 screen are so hard to come by. The ones with the coloured edges are sufficient to cover up the defects around the edges but I find the glare on them terrible.
Click to expand...
Click to collapse
here you go, sorry for late reply, your post didn't appear in my notifications
the case is by cafele, the skin protector is from here
https://www.tokopedia.com/bbgadget/xiaomi-mi6-tempered-glass-3d-full-cover-curved-cnc-cold-carving
https://www.tokopedia.com/bbgadget/cafele-xiaomi-mi6-mi-6-ultra-thin-case-tpu-matte

ZackoFF96 said:
here you go, sorry for late reply, your post didn't appear in my notifications
the case is by cafele, the skin protector is from here
https://www.tokopedia.com/bbgadget/xiaomi-mi6-tempered-glass-3d-full-cover-curved-cnc-cold-carving
https://www.tokopedia.com/bbgadget/cafele-xiaomi-mi6-mi-6-ultra-thin-case-tpu-matte
Click to expand...
Click to collapse
Nice glass protector.
I'm using the Nillkin and it's pretty good also.

i use a non brand, from Chinese, tempered glass.
but it's 3D, edge to edge, curved tempered glass, covers fully until the metal sides
it even works perfectly with a case, full protection till the edge of the case
not sure if it can be found outside my country though, since its a no brand thing
can post a pic if you guys want to see
Click to expand...
Click to collapse
link ?

idan357 said:
link ?
Click to expand...
Click to collapse
here you go
ZackoFF96 said:
here you go, sorry for late reply, your post didn't appear in my notifications
the case is by cafele, the skin protector is from here
https://www.tokopedia.com/bbgadget/xiaomi-mi6-tempered-glass-3d-full-cover-curved-cnc-cold-carving
https://www.tokopedia.com/bbgadget/cafele-xiaomi-mi6-mi-6-ultra-thin-case-tpu-matte
Click to expand...
Click to collapse

Greetings.
I have a Kapaver solid case, specifically this ...
https://www.amazon.com/gp/aw/d/B071...s=Case+mi6&dpPl=1&dpID=51MwFWjHV3L&ref=plSrch
The case alone I recommend, the touch of the case and the design seems excellent, and gives a very good feeling of protection of the casing, the problem arises when I supplement it with a tempered glass screen protector brand SMTR that I purchased, in particular this ...
https://www.amazon.es/Protector-Pant...X76P4DZ0K67DWZ
The tempered glass soon after putting the case up, I tried with the 2 crystals that are included, and both are detached. They do not seem to detach on their own, but when they put the case on, they leverage and raise them.
My question is:
With a protector that protects curved edges may not happen to me?
What protector do you recommend me with a rigid case like the one I have?
Thanks in advance.
Enviado desde mi MI 6 mediante Tapatalk

canariohippie said:
Greetings.
I have a Kapaver solid case, specifically this ...
https://www.amazon.com/gp/aw/d/B071...s=Case+mi6&dpPl=1&dpID=51MwFWjHV3L&ref=plSrch
The case alone I recommend, the touch of the case and the design seems excellent, and gives a very good feeling of protection of the casing, the problem arises when I supplement it with a tempered glass screen protector brand SMTR that I purchased, in particular this ...
https://www.amazon.es/Protector-Pant...X76P4DZ0K67DWZ
The tempered glass soon after putting the case up, I tried with the 2 crystals that are included, and both are detached. They do not seem to detach on their own, but when they put the case on, they leverage and raise them.
My question is:
With a protector that protects curved edges may not happen to me?
What protector do you recommend me with a rigid case like the one I have?
Thanks in advance.
Enviado desde mi MI 6 mediante Tapatalk
Click to expand...
Click to collapse
I think my screen protector wouldn't fit with your case, since the lips of your case is far more towards the screen, my case's lips is shorter, just barely towards the screen

Hi, I have same screen protector as ZackFF96.
It can be bought from AliExpress, this is the exact one I purchased:
https://www.aliexpress.com/item/3D-...rved-Edge-Frosted-Protective/32828496451.html
You can find more listings if you search "mi 6 4d glass".
Just make sure it has a similar style plastic backing on the screen protector. This is the only type of glass screen protector I have found to be full cover and full glue on back of glass.
This type of glass screen protector goes almost to the edge of screen, it leaves about 0.25mm of glass around the edge. It also covers about 0.25mm of the sides of the screen, only noticeable in apps which have lines going down the very side of the screen.
I use this case and it fits perfectly with the glass screen protector.
https://www.aliexpress.com/item/For...-and-Silicone-Back-Cover-for/32688209331.html
Compatible with pretty much all cases, I think only the very bulky cases like wooden or big armour cases will not fit. You will need to have the screen protector applied almost perfect though, if too much to one side or corner the case will foul on the glass.

HELP
Hello , i buyed xiaomi MI6 and screenprotector nillkin H+PRO 9H can someone please can suggsest me the phone cover now witch fits perfectly. I really dont want that between the phone case and screenprotector that there will be ugly line between them (not covered area ) hope you guys understand my bad english . I would love to buy that one if you to alieexpress and search "xiaomi mi 6 black gold cover" and there the first one ( i cant post links because i am new user. is this cover and the class fits perfectly . ty for your help

I use a film of hydrogel ...
https://goo.gl/rCpDpZ

jurarj said:
I use a film of hydrogel ...
https://goo.gl/rCpDpZ
Click to expand...
Click to collapse
Mate could you post some pic? i would like to see the final result , i ordered as well.
thanks

Ringke Invisible Defender (tempered glass) + Ringke Fusion-X (casing)

I initially planned to only buy the casing from Ringke since I prefer how it looks compared to Spigen's. However, I then noticed that Ringke also produced tempred glass for Poco F1, so I ordered them both and have been using them for several days now.
Ringke Invisible Defender - tempered glass
This one came a couple days earlier than the case, so I have it on first while using the default casing.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here are some of my thoughts:
There's not much of a problem precision-wise, the top and bottom part are well covered, the glass went way over the screen and into the bezel (Image A)
The side part is covered very precisely and didn't go over to the bezel part, too tight that for me it led to the issue below (Image B)
When in the dark, tilting the phone to the side reveal this rainbowish lines (Image C)
Using only the default slim casing, you can feel the edges of the glass are somewhat rough. The Ringke case below fixes this issue for me though, as the case cuts higher than the glass so it covers the rough gap. Ringke did explained on the product's page about having inevitable lifted sides due to the curved nature of the phone screen, so this might be the reason of that rough edge.
Ringke Fusion-X Casing
I've never use Ringke products prior to this phone, the packaging of the casing is somewhat minimalist. When applied to the phone, however, it feels satisfyingly fit to the phone. I have no complaint with the precision so far.

One more thing on the tempered glass: No oleophobic coating, it's a fingerprint magnet

Im fine with ringke fusion X case and Nillkin tempered glass.eeheheh. paired with a ringke strap

philsuf said:
One more thing on the tempered glass: No oleophobic coating, it's a fingerprint magnet
Click to expand...
Click to collapse
Thank you for this wonderful post I am planning to buy ringke case....I am using poco since past 5 months with default tpu case, now it is turning yellowish brown like tpu cases do after a while.... Can you tell me what is the material on the transparent back of rinkey case ? And please tell if it gets scratches after usage of few months.....
Also did you find a tempered glass with decent olephobic coating and also which is not a rip off. I'm happy with my current one, only one issue that it is a finger print magnet too.....The screen looks dirty when phone is locked and I have to constantly wipe it to keep it clean

Kobra.shady said:
Thank you for this wonderful post I am planning to buy ringke case....I am using poco since past 5 months with default tpu case, now it is turning yellowish brown like tpu cases do after a while.... Can you tell me what is the material on the transparent back of rinkey case ? And please tell if it gets scratches after usage of few months.....
Also did you find a tempered glass with decent olephobic coating and also which is not a rip off. I'm happy with my current one, only one issue that it is a finger print magnet too.....The screen looks dirty when phone is locked and I have to constantly wipe it to keep it clean
Click to expand...
Click to collapse
After 2 months of usage, no scratches yet. But I can't confirm on the back side material, my guess would be that it is plastic. So far I am really happy with the case, but not so much with the glass.
I still stick with the Ringke glass. My workaround is to coat it again with a liquid glass protection, just the cheap one. It isn't exactly fingerprint proof, but much better than using just the tempered glass.
Sent from my [device_name] using XDA-Developers Legacy app

philsuf said:
After 2 months of usage, no scratches yet. But I can't confirm on the back side material, my guess would be that it is plastic. So far I am really happy with the case, but not so much with the glass.
I still stick with the Ringke glass. My workaround is to coat it again with a liquid glass protection, just the cheap one. It isn't exactly fingerprint proof, but much better than using just the tempered glass.
Click to expand...
Click to collapse
Cool n thanks for quick reply...if you bought that liq glass protection online...can u please send me the link, I'll really appreciate it ?
And I was just worried about scratches on the back panel, since yours is okay so now I will happily buy Ringke case ?
And for the tempered glass I need to find something.... Hopefully that solution you are using will help.. because online if you buy tempered glass they say it has olephobic coating and anti finger print in product description but mostly it's just gimmick ??
C this is how smugged my phone gets....And it may look that I have touched it with oily figures, but trust me that ain't the case

Kobra.shady said:
Cool n thanks for quick reply...if you bought that liq glass protection online...can u please send me the link, I'll really appreciate it
And I was just worried about scratches on the back panel, since yours is okay so now I will happily buy Ringke case
And for the tempered glass I need to find something.... Hopefully that solution you are using will help.. because online if you buy tempered glass they say it has olephobic coating and anti finger print in product description but mostly it's just gimmick
C this is how smugged my phone gets....And it may look that I have touched it with oily figures, but trust me that ain't the case
Click to expand...
Click to collapse
It looks not good but the glass seems very protective!!
It covers very well!! :good:

Kobra.shady said:
Cool n thanks for quick reply...if you bought that liq glass protection online...can u please send me the link, I'll really appreciate it [emoji4]
And I was just worried about scratches on the back panel, since yours is okay so now I will happily buy Ringke case [emoji3]
And for the tempered glass I need to find something.... Hopefully that solution you are using will help.. because online if you buy tempered glass they say it has olephobic coating and anti finger print in product description but mostly it's just gimmick [emoji51][emoji14]
C this is how smugged my phone gets....And it may look that I have touched it with oily figures, but trust me that ain't the case
Click to expand...
Click to collapse
No problem, happy to help. However, I can't help you with the link, as I don't think any store here (Indonesia) will ship overseas.
Whoa, that is a really bad case of prints you got there. When I said my glass is fingerprint magnet (before I put liquid coating), it actually wasn't even half as bad as yours!
Anyway, I am using this liquid to make up for that problem:
https://shopee.co.id/novanrara22/1435201737?version=d8a482c89f545d4b74c105cce349c2ba
Cost me less than a couple of dollars
Sent from my [device_name] using XDA-Developers Legacy app

penna_85 said:
It looks not good but the glass seems very protective!!
It covers very well!! :good:
Click to expand...
Click to collapse
Yup it's very protective, doesn't block any part of screen or notch display, but yes only issue is finger print marks...rest I am happy with it..
---------- Post added at 12:28 PM ---------- Previous post was at 12:25 PM ----------
philsuf said:
No problem, happy to help. However, I can't help you with the link, as I don't think any store here (Indonesia) will ship overseas.
Whoa, that is a really bad case of prints you got there. When I said my glass is fingerprint magnet (before I put liquid coating), it actually wasn't even half as bad as yours!
Anyway, I am using this liquid to make up for that problem:
https://shopee.co.id/novanrara22/1435201737?version=d8a482c89f545d4b74c105cce349c2ba
Cost me less than a couple of dollars
Click to expand...
Click to collapse
?? Told you it's really annoying, I have to keep wiping my screen after few hours or it looks quite dirty...I will try to find similar kind of solution here, or get tempered glass from local market instead of online, because online u can not be sure ? even this tempered said "anti figure print" ????