Related
Hi,
I've been looking for instructions and stuff for rooting my phone Honor 7 Lite (NEM-L21) but I haven't found anything. The only valuable information I discovered was that Honor 7 Lite is probably a renamed Honor 5C for an european market. Some websites said it was renamed because there were changes in hardware (for example Honor 7 Lite supposedly doesn't have a fingerprint scanner, they say - but it's not true, from my experience I can say my phone does have it). So these websites can't be trusted anyway I guess. These two models look alike but I was thinking there could be differences anyway. I don't want to brick my phone. Has anybody tried to root this phone? Can anybody provide me any information about rooting it?
I'm sorry for my poor English and thank you very much for any answer.
Hi,
I have Honor 7 Lite NEM-L21 rooted by using method for Honor 5C. But before rooting, You must have an unlocked bootloader. Steps are:
1. unlock bootloader, after unlocking bootloader, phone will be wiped, so backup your data first - http://www.modaco.com/forums/topic/...our-honor-5c-official-and-unofficial-methods/
2. install custom twrp recovery for Honor 5c (known also as Huawei Nemo and Honor 7 Lite) - https://twrp.me/devices/huaweihonor5c.html
3. after installing twrp i recommend doing backup of boot, cust, oeminfo and system partitions to SD card
4. and now is possible install SuperSU zip from twrp recovery. Some instructions on the net recommends using the SuperSU-2.65 - https://download.chainfire.eu/921/SuperSU
Big Red Warning: for now, there are no firmware released for NEM-L21 in UPDATE.APP form for reflashing the phone from the Huawei eRecovery in case of if you bricked the phone. So, please do things carefully. I strongly recommends to do point 3 ASAP after installing twrp.
circulus said:
Hi,
I have Honor 7 Lite NEM-L21 rooted by using method for Honor 5C. But before rooting, You must have an unlocked bootloader. Steps are:
1. unlock bootloader, after unlocking bootloader, phone will be wiped, so backup your data first - http://www.modaco.com/forums/topic/...our-honor-5c-official-and-unofficial-methods/
2. install custom twrp recovery for Honor 5c (known also as Huawei Nemo and Honor 7 Lite) - https://twrp.me/devices/huaweihonor5c.html
3. after installing twrp i recommend doing backup of boot, cust, oeminfo and system partitions to SD card
4. and now is possible install SuperSU zip from twrp recovery. Some instructions on the net recommends using the SuperSU-2.65 - https://download.chainfire.eu/921/SuperSU
Big Red Warning: for now, there are no firmware released for NEM-L21 in UPDATE.APP form for reflashing the phone from the Huawei eRecovery in case of if you bricked the phone. So, please do things carefully. I strongly recommends to do point 3 ASAP after installing twrp.
Click to expand...
Click to collapse
+1. This is the only safest way OP.
Sent from my honor 5X using XDA Labs
Instructions for rooting Honor 7 Lite/5C NEM-L21 b100 are relatively easy to find and follow: unlock with Huawei's code, flash TWRP and SuperSu...
But for me, rooting before updating firmware was a big mistake! Wish I didn't unlock&root this phone yet; should have just updated with FF.
After rooting i wanted to FF update b100 -> b351 Nougat7/EMUI5... But it required stock recovery, which I had already flashed to TWRP, damn!
Now, another option would have been to flash custom ROM, but I didn't find great ROMs around, just somewhat commercial LineageOS (lacks e.g. dual-sim support)
Anyway, I tried to flash b100 -> b351 with TWRP, failed and ended up with test-keys firmware. Then tried to download FF, but the only input method in test-keys seemed to be google voice instead of keyboard = no success.
Then couldn't find stock recovery.img anywhere, so extracted it from stock update.app with extractor. Luckily the extractor had linux version too.
Then flashed stock recovery, updated with update.app method from test-keys to b132, then FF update to b351.
Doesn't seem possible to root b351 yet; now waiting for Nougat7/EMUI5-compatible version of TWRP.
Last time i modified some Android phone 5 years ago, so count me as n00b sharing this bad experience. Hopefully somebody could learn something
Hello everyone.
I tried rooting with the method mentioned by circulus. Running into a wall, can't get TWRP to start, only thing I get is the default EMUI recovery. Honor 7 lite, Android 6.0, EMUI 4.1.2 and bootloader is obviously unlocked.
Any ideas?
tehrek said:
Hello everyone.
I tried rooting with the method mentioned by circulus. Running into a wall, can't get TWRP to start, only thing I get is the default EMUI recovery. Honor 7 lite, Android 6.0, EMUI 4.1.2 and bootloader is obviously unlocked.
Any ideas?
Click to expand...
Click to collapse
Why you can't open TWRP, what your phone shows, if you tryin' to enter TWRP?
tehrek said:
Hello everyone.
I tried rooting with the method mentioned by circulus. Running into a wall, can't get TWRP to start, only thing I get is the default EMUI recovery. Honor 7 lite, Android 6.0, EMUI 4.1.2 and bootloader is obviously unlocked.
Any ideas?
Click to expand...
Click to collapse
Try to flash 3.0.2.0 Nemo TWRP, let me know if there are any problems left.
Got a Honor 7 lite, and i used special twrp and superSu from this post to root it :
https://forum.xda-developers.com/huawei-p9lite/development/twrp-t3588356 ---> for EMUI 5.X / Android Nougat
Work so fine.
Enjoy
Plz use a forum for honor 7 or 7 lite in xda . U will.get more support there than here
gopinaidu77 said:
Plz use a forum for honor 7 or 7 lite in xda . U will.get more support there than here
Click to expand...
Click to collapse
this is honor 7 lite xda forum... 5c=honor 7 lite....
thelous said:
this is honor 7 lite xda forum... 5c=honor 7 lite....
Click to expand...
Click to collapse
Hahahaha , never knew this . Thanks for making me aware of ..
Hi. I got a Honor 7 Lite NEM-L21 with Emui 5.0 and bootloader is unlocked. I have tried to flash TWRP with a pc with the command: fastboot flash recovery <filename>.img. The img file is in the platform-tools folder and cmd.exe says that it succeed. But when I try to reboot to recovery its just stuck in the screen your device is unlocked and cant be trusted your device is booting now and then nothing really happens. Any solution? Firmware: Nougat 7.0 B351
EeliX7 said:
Hi. I got a Honor 7 Lite NEM-L21 with Emui 5.0 and bootloader is unlocked. I have tried to flash TWRP with a pc with the command: fastboot flash recovery <filename>.img. The img file is in the platform-tools folder and cmd.exe says that it succeed. But when I try to reboot to recovery its just stuck in the screen your device is unlocked and cant be trusted your device is booting now and then nothing really happens. Any solution? Firmware: Nougat 7.0 B351
Click to expand...
Click to collapse
Holding power button and letting it reboot takes u to homescreen?
gopinaidu77 said:
Holding power button and letting it reboot takes u to homescreen?
Click to expand...
Click to collapse
No... Its stuck in the warning screen... I can still boot the system by holding power but if I attempt to reboot to recovery, its stuck in that warning. I can't access my PC just yet so it would be nice to be able to reboot to recovery without a PC.
EeliX7 said:
No... Its stuck in the warning screen... I can still boot the system by holding power but if I attempt to reboot to recovery, its stuck in that warning. I can't access my PC just yet so it would be nice to be able to reboot to recovery without a PC.
Click to expand...
Click to collapse
power off your device and make sure you don't have connections to phone ,then hold thevolume up and power after vibrate release power ,it will reboot to recovery
if it stucks flash the recovery again via fastboot
venugopalu007 said:
power off your device and make sure you don't have connections to phone ,then hold thevolume up and power after vibrate release power ,it will reboot to recovery
if it stucks flash the recovery again via fastboot
Click to expand...
Click to collapse
Flashed a P9 Lite version of TWRP, works great!
https://forum.xda-developers.com/huawei-p9lite/development/twrp-t3588356/page20
venugopalu007 said:
power off your device and make sure you don't have connections to phone ,then hold thevolume up and power after vibrate release power ,it will reboot to recovery
if it stucks flash the recovery again via fastboot
Click to expand...
Click to collapse
Do u know his Android version?
gopinaidu77 said:
Do u know his Android version?
Click to expand...
Click to collapse
emui 5.0 ,he said in his first post
venugopalu007 said:
emui 5.0 ,he said in his first post
Click to expand...
Click to collapse
Ok
Hi fellas.
Been busy but got an update, phone is successfully rooted now. Brainfarted a bit earlier and wasn't booting to TWRP.
Me no brain sometiems.
I want to flash my phone with stock firmware, but I cannot find it anywhere.
I am looking for PRA-LX1C738B123.
I own Huawei p8 lite 2017
I wiped my system because I wanted to install other rom, it didn't work so I want to go back to the original.
Unfortunately I wasn't smart enough to do a backup before so I am stuck atm. The bootloader is unlocked and flashing works, I can boot into huawei eRecovery and TWRP. (eRecovery gives the getting package info failed error) I have tried the dload method with other app files, it fails at 5% every time tho.
I tried using Huawei Update Extractor and Firmware Finder but I cannot find the exact firmware.
Could someone help me with installing my firmware? Oh and I am kinda new and it would be nice to get some guides,
Thanks.
I have the same problem but with a different firmware.. now only thing i can do is use dc-phoenix paid software (15$ for 72h of use). I will try that tomorrow as i also can't find exact same firmware it was on my phone.
MobileTechArena said:
I have the same problem but with a different firmware. now only thing i can do is usedc-phoenix paid software (15$ for 72h of use). I will try that tomorrow as i also can't find exact same firmware it was on my phone.
Click to expand...
Click to collapse
Thanks for reply. I will take that into consideration, but from what I see you were looking for PRA-LX1C432B106 and they indeed have the c432 roms there, however they don't seem to have the ones that I have been looking for. They have a list of firmwares online. Anyway good luck.
barnabaXXX said:
Thanks for reply. I will take that into consideration, but from what I see you were looking for PRA-LX1C432B106 and they indeed have the c432 roms there, however they don't seem to have the ones that I have been looking for. They have a list of firmwares online. Anyway good luck.
Click to expand...
Click to collapse
Yes, but any PRA-LX1C432 i tried doesn't work for me, flashing by fastboot. I believe any PRA-LX1 should work on this phone, but i will need to use that dc phoenix software to flash it.
MobileTechArena said:
Yes, but any PRA-LX1C432 i tried doesn't work for me, flashing by fastboot. I believe any PRA-LX1 should work on this phone, but i will need to use that dc phoenix software to flash it.
Click to expand...
Click to collapse
Thanks for making it clear. Please tell me if it worked or not. Thanks.
barnabaXXX said:
I want to flash my phone with stock firmware, but I cannot find it anywhere.
I am looking for PRA-LX1C738B123.
I own Huawei p8 lite 2017
I wiped my system because I wanted to install other rom, it didn't work so I want to go back to the original.
Unfortunately I wasn't smart enough to do a backup before so I am stuck atm. The bootloader is unlocked and flashing works, I can boot into huawei eRecovery and TWRP. (eRecovery gives the getting package info failed error) I have tried the dload method with other app files, it fails at 5% every time tho.
I tried using Huawei Update Extractor and Firmware Finder but I cannot find the exact firmware.
Could someone help me with installing my firmware? Oh and I am kinda new and it would be nice to get some guides,
Thanks.
Click to expand...
Click to collapse
Hello ! I think I could be of some help since I encountered the exact same problem !
edit: well I just realized I can't find your ROM with firmware finder either, sorry for the failed attempt
In your case I'd try with each firmware until one would work or a I tried them all.
You need some utilities first :
- Firmware Finder
https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
It will allow you to find the stock ROM that fits your model
-Huawei UPDATE extractor
https://forum.xda-developers.com/showthread.php?t=2433454
It will allow you to extract the .img files from the firmware previously downloaded.
-fastboot and adb
https://forum.xda-developers.com/showthread.php?t=2317790
The programs that will allow you to flash the .img files.
Now:
1. Find your ROM using firmware finder (the model is usually on the box you received the android in).
2.Extract the necessary .img files : system.img, boot.img, recovery.img.
3.Reboot into the bootloader, connect your device to your computer, open a cmd exe (powershell in my case) by holding shift+right click on the folder containing the .img files and flash each .img file, e.g. for the system file:
"fastboot flash system system.img"
4.then use "fastboot reboot" and after that shutdown your device
(in my case even after flashing the .img files I was greeted by a blank screen, so I shutdown my device holding the power button).
5. Boot into recovery holding vol up + power buttons (be sure to disconnect your device before shutting down and powering it up again) and choose factory reset.
It should then reboot into ROM installation procedure where you will have to follow the same steps as when you booted your device for the first time.
edit: formatting
Also, as far as my limited knowledge goes, there is no custom ROM officially supported for our dear device.
JStrel said:
Hello ! I think I could be of some help since I encountered the exact same problem !
edit: well I just realized I can't find your ROM with firmware finder either, sorry for the failed attempt
In your case I'd try with each firmware until one would work or a I tried them all.
You need some utilities first :
- Firmware Finder
https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
It will allow you to find the stock ROM that fits your model
-Huawei UPDATE extractor
https://forum.xda-developers.com/showthread.php?t=2433454
It will allow you to extract the .img files from the firmware previously downloaded.
-fastboot and adb
https://forum.xda-developers.com/showthread.php?t=2317790
The programs that will allow you to flash the .img files.
Now:
1. Find your ROM using firmware finder (the model is usually on the box you received the android in).
2.Extract the necessary .img files : system.img, boot.img, recovery.img.
3.Reboot into the bootloader, connect your device to your computer, open a cmd exe (powershell in my case) by holding shift+right click on the folder containing the .img files and flash each .img file, e.g. for the system file:
"fastboot flash system system.img"
4.then use "fastboot reboot" and after that shutdown your device
(in my case even after flashing the .img files I was greeted by a blank screen, so I shutdown my device holding the power button).
5. Boot into recovery holding vol up + power buttons (be sure to disconnect your device before shutting down and powering it up again) and choose factory reset.
It should then reboot into ROM installation procedure where you will have to follow the same steps as when you booted your device for the first time.
edit: formatting
Also, as far as my limited knowledge goes, there is no custom ROM officially supported for our dear device.
Click to expand...
Click to collapse
Thanks for help! I tried but i dont' have factory reset option. All I have is Shutdown, reboot and "Download leastest version and recovery" and after I click that all it does is wants internet connection. I logged in to my wifi but it didn't work and I ended up with "getting package info failed screen".
barnabaXXX said:
Thanks for help! I tried but i dont' have factory reset option. All I have is Shutdown, reboot and "Download leastest version and recovery" and after I click that all it does is wants internet connection. I logged in to my wifi but it didn't work and I ended up with "getting package info failed screen".
Click to expand...
Click to collapse
Yes I had the exact same problem, but once I did what I described, by rebooting into recovery (without twrp), I finally had the option to restore factory settings.
I believe the issue is in the fact you don't have access to the stock ROM for your model.
JStrel said:
Yes I had the exact same problem, but once I did what I described, by rebooting into recovery (without twrp), I finally had the option to restore factory settings.
I believe the issue is in the fact you don't have access to the stock ROM for your model.
Click to expand...
Click to collapse
I got rom that allows me to do a factory reset, it's stuck at 99% for like 2 hours now, is it normal? If not what should I do?
barnabaXXX said:
I got rom that allows me to do a factory reset, it's stuck at 99% for like 2 hours now, is it normal? If not what should I do?
Click to expand...
Click to collapse
Unfortunately I can't help you further than what I already posted.
But keep updating in case someone more knowledgeable peeks in.
similar problem....I was fairly good but play store was stuck in pending download....
I did a wipe in TWRP, and ended with a black screen...
I can boot to eRecovery, but it fails.and also to TWRP.
when attached to PC it keeps being seen and unseen as if its stuck in a power on cycle
Any help would be greatly appreciated.
Already Tested
JStrel said:
Hello ! I think I could be of some help since I encountered the exact same problem !
edit: well I just realized I can't find your ROM with firmware finder either, sorry for the failed attempt
In your case I'd try with each firmware until one would work or a I tried them all.
You need some utilities first :
- Firmware Finder
https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
It will allow you to find the stock ROM that fits your model
-Huawei UPDATE extractor
https://forum.xda-developers.com/showthread.php?t=2433454
It will allow you to extract the .img files from the firmware previously downloaded.
-fastboot and adb
https://forum.xda-developers.com/showthread.php?t=2317790
The programs that will allow you to flash the .img files.
Now:
1. Find your ROM using firmware finder (the model is usually on the box you received the android in).
2.Extract the necessary .img files : system.img, boot.img, recovery.img.
3.Reboot into the bootloader, connect your device to your computer, open a cmd exe (powershell in my case) by holding shift+right click on the folder containing the .img files and flash each .img file, e.g. for the system file:
"fastboot flash system system.img"
4.then use "fastboot reboot" and after that shutdown your device
(in my case even after flashing the .img files I was greeted by a blank screen, so I shutdown my device holding the power button).
5. Boot into recovery holding vol up + power buttons (be sure to disconnect your device before shutting down and powering it up again) and choose factory reset.
It should then reboot into ROM installation procedure where you will have to follow the same steps as when you booted your device for the first time.
edit: formatting
Also, as far as my limited knowledge goes, there is no custom ROM officially supported for our dear device.
Click to expand...
Click to collapse
Hello did you already test ???
Here is the solution for every PRA-LX1: [http : // www . htcmania . com / showthread . php ? t=1326478] (sorry for the spaces, but I don't have enough posts written to post external links )
Unfortunately, it's from a spanish forum. I didn't found any problem to follow this tutorial, but maybe for someone it could be a little difficult.
Anyway, it works!
MobileTechArena said:
Yes, but any PRA-LX1C432 i tried doesn't work for me, flashing by fastboot. I believe any PRA-LX1 should work on this phone, but i will need to use that dc phoenix software to flash it.
Click to expand...
Click to collapse
Where did you find the C432 firmware? I can't succees to find it
Flashing to a completely empty phone via DC phoenix or manual via fastboot still didnt got my device started. Sometimes I end up in the eRecovery and sometimes its just stuck at boot.
I tried different version from the hicloud but none so far did the trick. Maybe someone can point me into the right direction so i can finally rescue this phone?
EDIT:
PRA-LX1C432
Sorry cant link to these files since i don't got 10 posts. Maybe PM ?
Copied the Mega TWRP backup (B100) to SD card
Flashed TWRP via fastboot
Disconnected the USB cable
Boot into TWRP
Restored TWRP backup
Restarted phone into fastboot
OEM unlocked it
Got booted into TWRP since no stock recovery there
Booted into fastboot again
flashed stock recovery
Android started to work!
Tried to update to B164 and failed
Reboot
Now it offered B110 and I tried to update to B110. Success.
Iocere said:
Flashing to a completely empty phone via DC phoenix or manual via fastboot still didnt got my device started. Sometimes I end up in the eRecovery and sometimes its just stuck at boot.
I tried different version from the hicloud but none so far did the trick. Maybe someone can point me into the right direction so i can finally rescue this phone?
EDIT:
PRA-LX1C432
Sorry cant link to these files since i don't got 10 posts. Maybe PM ?
Copied the Mega TWRP backup (B100) to SD card
Flashed TWRP via fastboot
Disconnected the USB cable
Boot into TWRP
Restored TWRP backup
Restarted phone into fastboot
OEM unlocked it
Got booted into TWRP since no stock recovery there
Booted into fastboot again
flashed stock recovery
Android started to work!
Tried to update to B164 and failed
Reboot
Now it offered B110 and I tried to update to B110. Success.
Click to expand...
Click to collapse
Yeah, that's the way! It worked for me too!
juanmemo said:
Yeah, that's the way! It worked for me too!
Click to expand...
Click to collapse
Also i noticed everytime a OTA fails you get the full version offered on next boot. So you should get a full B164 aswell after it failed
JStrel said:
Yes I had the exact same problem, but once I did what I described, by rebooting into recovery (without twrp), I finally had the option to restore factory settings.
I believe the issue is in the fact you don't have access to the stock ROM for your model.
Click to expand...
Click to collapse
how can you boot into recovery ? i can only boot into twrp or fastboot & rescue or if i plug the huawei to the pc erecovery ???
---------- Post added at 12:16 AM ---------- Previous post was at 12:13 AM ----------
i have an huawei pra-lx1 c530 it used to boot into pra-lx1c530b111 rooted and twrp but now it doens't boot anymore, i'd like to flash to c530b160 but i can't find the firmware images
tiagoggama said:
Hello did you already test ???
Click to expand...
Click to collapse
Thanks men
I CONFIRM IT WORK PERFECTLY
For the second part go to this link for more detail :
https://boycracked.com/2016/03/14/h...-unbrick-firmware-any-huawei-android-devices/
Hello everyone, I am trying to install the latest Global dev ROM on my Mi8.
I bought the phone from Gearbest and it arrived with the latest Russian stable ROM and unlocked bootloader.
The thing is I think the person who did all the above messed something up because I can't install the ROM I want using the standard procedures with TWRP, XiaomiMiTool or Mi Flash.
TWRP
When I try to install TWRP (version 918), when I reboot with the reboot command and use the flash command, I see some random errors (couldn't get max-size report for example) or the command does nothing, so I am not able to install it.
XiaomiMiTool
The program recognises the phone, I select the global dev rom, it makes its checks, then it tries (failing of course) to unblock the already unblocked bootloader and I cannot proceed any farther
Miflash
Booted the phone in fastboot, found in the program list, check "clean all" only, when I click flash the phone goes into a black screen with a "press any key to shutdown" in the top left corner of the screen
Any advice on how to resolve any of these problems please? Maybe something got corrupted like the boot.img or recovery.img?
I can provide with some screenshoots and photos and list of commands I was using if it's going to be of any help
Thanks
Install adb and flash it through.
krepsz said:
Install adb and flash it through.
Click to expand...
Click to collapse
Flash what? The recovery? I've tried that already The ROM? I need TWRP first
https://www.xda-developers.com/how-to-install-twrp/
krepsz said:
https://www.xda-developers.com/how-to-install-twrp/
Click to expand...
Click to collapse
Thank you for this, but this is the same guide I followed.
After I use the flash command either nothing happens or I get an error.
The image below is after I waited 5 mins
OK.I recommend you TWRP 3.2.2-0711 wzsx150 from LR.TEAM linkhttps://forum.xda-developers.com/mi-8/how-to/recovery-twrp-3-2-2-0703-t3812600
,and also i recommend you insted of Global rom the EU rom.Its many language included and have better performance and camera.
I resolved this problem changing pc with USB 2.0 ports.
Hi there
I am a newbie of Xiaomi Phone. I got a used Mi 11 Ultra phone from a reputable eBay User. My phone is currently installed with a stable version called MIUI 13/.0 (V13.0.12.0.SKACNXM STABLE). Since I am new to this phone, I click on system updates and managed to download a file called xiaomi.eu_Multi_M11Pro_M11Ultra_V13.0.13.0.SKACNXM_618A7FFAB_V13-12.ZIP Via OTA Updates.
After I click on the Updates Button, I got a screen with a green button : "Check MD5 & Install", after a while, I got a pop up screen says :Your device supports "Seamless System Updates",
I click on the OK button, also click on the OK button for the internal storage is encrypted.
Finally, to ask me whether I would like to continue to install the Updates, I choose YES and end up stuck at the Main Menu with 5 choices: Reboot, Wipe Data, Connect with MiAssistant, Safe Mode and Repair Mode. There are no choice for me to install the Updates.
Can someone give me a hand please ?
Many thanks in advance.
gomcse2002 said:
Hi there
I am a newbie of Xiaomi Phone. I got a used Mi 11 Ultra phone from a reputable eBay User. My phone is currently installed with a stable version called MIUI 13/.0 (V13.0.12.0.SKACNXM STABLE). Since I am new to this phone, I click on system updates and managed to download a file called xiaomi.eu_Multi_M11Pro_M11Ultra_V13.0.13.0.SKACNXM_618A7FFAB_V13-12.ZIP Via OTA Updates.
After I click on the Updates Button, I got a screen with a green button : "Check MD5 & Install", after a while, I got a pop up screen says :Your device supports "Seamless System Updates",
I click on the OK button, also click on the OK button for the internal storage is encrypted.
Finally, to ask me whether I would like to continue to install the Updates, I choose YES and end up stuck at the Main Menu with 5 choices: Reboot, Wipe Data, Connect with MiAssistant, Safe Mode and Repair Mode. There are no choice for me to install the Updates.
Can someone give me a hand please ?
Many thanks in advance.
Click to expand...
Click to collapse
start with Repair Mode if it doesn't work Wipe Data(your data will be erased).
I tried both options but not working
Try installing TWRP recovery (permanent flash not just fastboot boot TWRP.img) and then retry the installation.
gomcse2002 said:
I tried both options but not working
Click to expand...
Click to collapse
Is the bootloader unlocked?
Unlock Bootloader - Install Twrp - install the latest xiaomi.eu rom - you can root with magisk.zip if necessary
NOSS8 said:
Is the bootloader unlocked?
Click to expand...
Click to collapse
May I know how to check whether the bootloader had been unlocked ? Thanks in advance.
gomcse2002 said:
May I know how to check whether the bootloader had been unlocked ? Thanks in advance.
Click to expand...
Click to collapse
Is the phone boot and is linked with your Xiaomi account?
NOSS8 said:
Is the phone boot and is linked with your Xiaomi account?
Click to expand...
Click to collapse
I don't have a Xiaomi account. The phone is working but cannot install updates properly because of the seamless updates.
gomcse2002 said:
I don't have a Xiaomi account. The phone is working but cannot install updates properly because of the seamless updates.
Click to expand...
Click to collapse
Ok, what do you want to do, update it to Chinese version or flash another version?
Do you know the Xiaomi EU roms?
For me looks like ROM what you had before was FASTBOOT installed xiaomi.eu stable, and then they started rolling out TWRP updates, and because you didn't have TWRP its reboot in stock recovery ?...
Can you boot into TWRP from this link:https://forum.xda-developers.com/t/...eamwin-recovery-project.4374111/post-87360425
Please use this fastboot command
Code:
fastboot boot recovery.img
, first TWRP boot will be in Chinese language, please change it to English, enter your unlock PIN, then find this update file downloaded by updater.
Let us know if that's help
I'm right, your current ROM is a FASTBOOT version (so without TWRP)
Checked on the download website
xiaomi.eu_multi_MI11Pro_MI11Ultra_V13.0.12.0.SKACNXM_v13-12-fastboot.zip
Click to expand...
Click to collapse
veimus said:
For me looks like ROM what you had before was FASTBOOT installed xiaomi.eu stable, and then they started rolling out TWRP updates, and because you didn't have TWRP its reboot in stock recovery ?...
Can you boot into TWRP from this link:https://forum.xda-developers.com/t/...eamwin-recovery-project.4374111/post-87360425
Please use this fastboot command
Code:
fastboot boot recovery.img
, first TWRP boot will be in Chinese language, please change it to English, enter your unlock PIN, then find this update file downloaded by updater.
Let us know if that's help
Click to expand...
Click to collapse
What are you talking about ?
Xiaomi Eu is a custom rom.
Xiaomi EEA rom for Europe is a stock rom.
V13.0.12.0.SKACNXM and V13.0.13.0.SKACNXM :Chinese stock rom
NOSS8 said:
What are you talking about ?
Xiaomi Eu is a custom rom.
Xiaomi EEA rom for Europe is a stock rom.
V13.0.12.0.SKACNXM and V13.0.13.0.SKACNXM :Chinese stock rom
Click to expand...
Click to collapse
You didn't focus on details ,my friend
He has already installed xiaomi.eu custom ROM, if you closely check his pictures from his first post - Updater app downloaded new version of xiaomi.eu CUSTOM ROM, so yeah he has already unlocked bootloader, and installed FASTBOOT version of CUSTOM ROM, the version what Updater app downloaded was released to be installed with TWRP (he didn't have TWRP on his phone yet) - so he need boot into TWRP and install update manually.
veimus said:
You didn't focus on details ,my friend
He has already installed xiaomi.eu custom ROM, if you closely check his pictures from his first post - Updater app downloaded new version of xiaomi.eu CUSTOM ROM, so yeah he has already unlocked bootloader, and installed FASTBOOT version of CUSTOM ROM, the version what Updater app downloaded was released to be installed with TWRP (he didn't have TWRP on his phone yet) - so he need boot into TWRP and install update manually.
Click to expand...
Click to collapse
You're right bro, I'm way off base.
I focused on that
he just installed the TWRP and updated.
TWRP
https://dl.akr-developers.com/?dir=skkk/TWRP/A12/v6.0_A12
To summarize:
Create a Xiaomi account.Important
I hope that the seller has deleted the device from his account otherwise it will be a hassle.
flash twrp
Flash the rom
Create a Xiaomi account.Important
Click to expand...
Click to collapse
He has already unlocked bootloader/already on custom ROM - for what he needs Xiaomi account ?
veimus said:
He has already unlocked bootloader/already on custom ROM - for what he needs Xiaomi account ?
Click to expand...
Click to collapse
because after flashing the ROM, it is asked to continue booting.
obviously if the phone is no longer linked this will not be a problem
Hi gomcse2002,
Has your problem been solved?
If so, how did you do it, if you don't mind me asking.
I've had the same exact concern on my Mi 11 Ultra, which sadly has NOT been resolved yet.
Thanks.
Which rom(full name)?
Hey everyone
I recently got this phone and went through the bootloader unlock process.
I then tried to follow the instructions on this page https://wiki.pixelexperience.org/devices/rosemary/install/ to get this rom installed but somehow ****ed it up.
Everything went well until I tried to flash the recovery img from this page: https://get.pixelexperience.org/rosemary (i downloaded the 13 plus recovery img).
I flashed the img via fastboot but after that I got stuck in fastboot. The phone is stuck in a bootloop when I try to reboot into recovery or normal boot. The only thing I can get back into is fastboot.
Would really appreciate any help to get the phone working again. Im not new to android custom roms but Im new to xiaomi phones and Im a little lost
Thanks.
OK nevermind I successfully got the phone booting again with miflash tool by reflashing an official firmware...
Greetings!
You can install the rom via adb sideload too. Put on some random recovery (see my tutorial here: https://forum.xda-developers.com/t/twrp-on-android-12.4522273/), and start adb sideload.
Then,
adb sideload insert_package_name.zip
Click to expand...
Click to collapse
Hope it helps! ; D
dona3000 said:
Hey everyone
I recently got this phone and went through the bootloader unlock process.
I then tried to follow the instructions on this page https://wiki.pixelexperience.org/devices/ros mary/install/ to get this rom installed but somehow ****ed it up.
Everything went well until I tried to flash the recovery img from this page: https://get.pixelexperience.org/rosemary (i downloaded the 13 plus recovery img).
I flashed the img via fastboot but after that I got stuck in fastboot. The phone is stuck in a bootloop when I try to reboot into recovery or normal boot. The only thing I can get back into is fastboot.
Would really appreciate any help to get the phone working again. Im not new to android custom roms but Im new to xiaomi phones and Im a little lost
Thanks.
Click to expand...
Click to collapse
Did u make sure ur on Miui 12.5.16.0.RKLMIXM?
I'm also having similar problem and circumstance, may I ask where did you find the official firmware and/or recovery img for the Redmi note 10s
fol!s said:
I'm also having similar problem and circumstance, may I ask where did you find the official firmware and/or recovery img for the Redmi note 10s
Click to expand...
Click to collapse
Greetings!
As this phone has an MTK processor, we don't really have a recovery image, it's stored in the boot img I suppose. That link, you can download the official rom to this. DISCLAIMER: There are two types of ROMs listed here, one type is fastboot, that you need now in order to flash it through a computer for example. The another type is the recovery rom, that you can flash from recovery like a magisk package, or anything flashable zip, or with adb sideload.
https://mifirm.net
You should choose global if you are in Europe, but it's suitable for devices in the US or USA probably, ony feature differences are here between an EEA and Global rom.
Also, if you install pixel experience recovery, you can install the firmware by going into recovery, and do it via sideload. Or, you can try flashing the rom with TWRP (tutorial linked below), but then you won't able to install updates automatically.
One question: Did you checked in OEM unlocking in developer options before flashed PE?
Hope it helps!
Yeah, I did checked the oem unlocking. I think the reason why i failed because my bootloader probably updated and I forgot to check. You need bootloader version 12.5.16.0.RKLMIXM to install the pixel experience. Also thank for help
Greetings!
You can install the rom via adb sideload too. Put on some random recovery (see my tutorial here: https://forum.xda-developers.com/members/gurtnyi.11842195), and start adb sideload.
Then,
adb sideload insert_package_name.zip
Hope it helps! ; D
Click to expand...
Click to collapse
Can I do that on newer firmware or should I roll back to version 12.5.16.0.RKLMIXM? And if I roll back then I need to unlock device again?
I think you can. I've flashed it successfully on the latest version too. Currently I don't use PE but it was good for me.
Well, regarding to the unlock, it's not a big deal, you don't have to wait 168h again, once you've firstly unlocked your device, you can re-unlock it again, and again, no matter how many times, you don't have to wait a lot again.
But depending on how you rollback it,
I mean, with xiaomi flasher (i think that's its name) you can choose between clean all and lock, save userdata, and clean all, but in the first case, it'll lock back the bootloader. With SP flash tool (if you need, I can provide a link for the modified version of it, that doesn't require an auth file, but if fails, you need a python script, I can link that too), as I remember it won't lock back the device, but I'm not a 100% sure
Hope it helps!
Can you repair link to totorial https://forum.xda-developers.com/members/gurtnyi.11842195 doesn't seem to work.
raven17a said:
Can you repair link to totorial https://forum.xda-developers.com/members/gurtnyi.11842195 doesn't seem to work.
Click to expand...
Click to collapse
Corrected, thank you!
Thank you! I managed to install PE by rolling back to MIUI 12.5. Sideload unfortunatly not working on stock recovery.
raven17a said:
Thank you! I managed to install PE by rolling back to MIUI 12.5. Sideload unfortunatly not working on stock recovery.
Click to expand...
Click to collapse
Happy to hear that!
By the way, yes, pe recovery is better for sideloading, or eventually any not stock recovery. Also, if you install PE recovery, you can apply updates automatically, and in the future you won't need to flash it manually.