I'm having a really hard time getting this OP3t to do what I want.
Didn't flash su after trying to manually update to 4.0.2
Constantly tried to flash a new rom, would get stuck at patching system
Tried to use unbrick solution, flashed stock recovery
Upon completion of unbrick solution my bootloader is locked and i cannot get into recovery because md5 checksum fail when booting.
I've tried using the unbricking solution probably 10 times with no change.
I have searched among the threads which have not be helpful enough to solve my solution.
right now it says modem, boot and system failed md5 checksum and just constantly reboots.
Also, phone is not being recognized now in fastboot mode
What do I do???
First of all try to open phone in fastboot mode then connect your cable to pc.
1. Download full stock rom of oos try 4.0.1.
2. use command to lock the bootloader
fastboot oem lock;
3. then flash stock recovery of nouguat 7.0 through fastbootmode .
fastboot flash recovery image.filename.
4. then go to stock recovery and flash full rom zip using adb sideload.
All done and best of luck......
If facing any problem then ask
shubham8166410 said:
First of all try to open phone in fastboot mode then connect your cable to pc.
1. Download full stock rom of oos try 4.0.1.
2. use command to lock the bootloader
fastboot oem lock;
3. then flash stock recovery of nouguat 7.0 through fastbootmode .
fastboot flash recovery image.filename.
4. then go to stock recovery and flash full rom zip using adb sideload.
All done and best of luck......
If facing any problem then ask
Click to expand...
Click to collapse
I'm getting the wont load problem when trying to flash, advice?
Place all the zip file in same folder of adb driver than try to flash it
---------- Post added at 05:58 PM ---------- Previous post was at 05:58 PM ----------
Is your phone booting in fast mode or nkt
shubham8166410 said:
Place all the zip file in same folder of adb driver than try to flash it
---------- Post added at 05:58 PM ---------- Previous post was at 05:58 PM ----------
Is your phone booting in fast mode or nkt
Click to expand...
Click to collapse
NKT? Not sure what that means.
It is going to fastboot however if i list adb devices nothing shows up.
It does respond with bootloader already locked when i try to send that command
Type command fastboot devices
---------- Post added at 06:11 PM ---------- Previous post was at 06:10 PM ----------
Then it will show device then only u can procceed further
shubham8166410 said:
Type command fastboot devices
---------- Post added at 06:11 PM ---------- Previous post was at 06:10 PM ----------
Then it will show device then only u can procceed further
Click to expand...
Click to collapse
Nothing is coming up when I do that, it just returns to the original command prompt line
Can u able to flash phone in fastboot mode or not
shubham8166410 said:
Can u able to flash phone in fastboot mode or not
Click to expand...
Click to collapse
I was able to use the unbrick method from another computer. Thank you for your assitance
Related
I attempted to flash ICS rom for my N1 and I know installation of Blackrose is required.
I attempted to use Blackrose.exe but it doesn't work, then I trun to flash the cutsome hboot by manual in command prompt.
But the problem is I get the signature verfiication failed when I tried to flash any hboot_xxxxx.nb0 files by fastboot.
I have searched some relevant threads but no clear solution was found. (Some threads have posted the similar question but all the replies are problem solved without clear explanation.)
Any anybody can advise me ? How can I pass the signature verification in fastboot ?
hthsolstice said:
I attempted to flash ICS rom for my N1 and I know installation of Blackrose is required.
I attempted to use Blackrose.exe but it doesn't work, then I trun to flash the cutsome hboot by manual in command prompt.
But the problem is I get the signature verfiication failed when I tried to flash any hboot_xxxxx.nb0 files by fastboot.
I have searched some relevant threads but no clear solution was found. (Some threads have posted the similar question but all the replies are problem solved without clear explanation.)
Any anybody can advise me ? How can I pass the signature verification in fastboot ?
Click to expand...
Click to collapse
Are you using RA recovery? While in recovery, select Flash zip from SD card, then select Toggle signature verification to turn off
You can't just flash "improper" HBOOT from fastboot, even if you have unlocked bootloader. HBOOT is still protected. There's a procedure that's needed to flash it, some script, I don't remember exactly what. Please look it up.
taodan: It is not the problem in the recovery, I can't write on the "hboot" in the bootloader
Jack_R1: Yes, that's I wanted to find out......
Try this if you haven't--of course nandroid first
Download latest Blackrose to PC and extract it
Open it and go to the binary folder
Copy the two files below to you fastboot.exe folder. Mine is in tools of my SDK
Do following
1) Boot into fastboot mode on your device, and plug it in to your computer.
2) Boot the exploit: fastboot boot go2.lol
3) Flash the modified hboot: fastboot flash hboot hboot_blackrose.nb0
You need to reboot your bootloader (fastboot reboot bootlloader) and check that it shows Blackrose installed and s-off
You still need to modify the hboot to ICS partition sizes, I use splhexeditor
---------- Post added at 07:18 PM ---------- Previous post was at 07:12 PM ----------
Also, what rom are you coming from. BR won't install over Sense roms
Somewher in thread dev mentions that if you can't install by selecting bootloader unlocked try locked and see if it works. Forget where that was and for what problem it was for.
Thanks a lot ! I can flash ICS rom now !!!
rugmankc said:
Try this if you haven't--of course nandroid first
Download latest Blackrose to PC and extract it
Open it and go to the binary folder
Copy the two files below to you fastboot.exe folder. Mine is in tools of my SDK
Do following
1) Boot into fastboot mode on your device, and plug it in to your computer.
2) Boot the exploit: fastboot boot go2.lol
3) Flash the modified hboot: fastboot flash hboot hboot_blackrose.nb0
You need to reboot your bootloader (fastboot reboot bootlloader) and check that it shows Blackrose installed and s-off
You still need to modify the hboot to ICS partition sizes, I use splhexeditor
---------- Post added at 07:18 PM ---------- Previous post was at 07:12 PM ----------
Also, what rom are you coming from. BR won't install over Sense roms
Somewher in thread dev mentions that if you can't install by selecting bootloader unlocked try locked and see if it works. Forget where that was and for what problem it was for.
Click to expand...
Click to collapse
hthsolstice,
No problem just hit Thanks--
Hey Guys, Thanks for anyone that can help.
HTC One M7 T-Mob, S-Off, unlocked, super CID. After switching to the wrong firmware that didn't allow LTE I re-installed and put the stock recovery back on, locked bootloader and re-installed my T-mob RUU.
Now I cannot re-install a recovery to gain root.
Here's where I'm at. S-off, super Cid "111.." unlocked bootloader, stock recovery.
I can see my phone in fastboot devices but not adb devices.
I have tried ( fastboot flash recovery recovery.img) but adb says "cannot load 'recovery.img'
Thinking it may be an adb/pc issues since neither of my PC's can see the device in adb devices only in fastboot devices I tried CW Mod and Goo Manager to flash the images. both failed.
So I'm kinda stuck. Hboot now 1.44 and have ran out of know options in my skill level.
Thanks in advance for any help.
And I know the adb not being able to see the device may be part of the problem, 2-3 different computers, different cords, fastload off, debugging on. It seems to see the device sometimes depending on the firmware that I'm on. And I have re-installed, deleted, updated, installed htc sync, than deleted it after the drivers loaded. I have pretty much tried everything.
Rob:crying:
Your recovery.img is either called something else or not in the same directory as fastboot.
And running fastboot can't cause adb to give you an error.
Adb doesn't work when the phone is in fastboot mode .
BenPope said:
Your recovery.img is either called something else or not in the same directory as fastboot.
And running fastboot can't cause adb to give you an error.
Adb doesn't work when the phone is in fastboot mode .
Click to expand...
Click to collapse
It is defiantly in the right directory, and with the right name as I have flashed it a couple times in the past. What gets me is if I take the PC out of the picture and just try to use CWM or GOO Mngr to flash it they both come up with an error or fail.
Any ideas on how to move forward and what to try next?
Coppo said:
I have tried ( fastboot flash recovery recovery.img) but adb says "cannot load 'recovery.img'
Click to expand...
Click to collapse
Coppo said:
It is defiantly in the right directory, and with the right name as I have flashed it a couple times in the past. What gets me is if I take the PC out of the picture and just try to use CWM or GOO Mngr to flash it they both come up with an error or fail.
Any ideas on how to move forward and what to try next?
Click to expand...
Click to collapse
Please clarify the first bit I just quoted... it says it can't find the file. The obvious conclusion is that the file is not there under the specified name.
In fact, just run these commands and post the entire output here:
Code:
dir
fastboot flash recovery recovery.img
BenPope said:
Please clarify the first bit I just quoted... it says it can't find the file. The obvious conclusion is that the file is not there under the specified name.
In fact, just run these commands and post the entire output here:
Code:
dir
fastboot flash recovery recovery.img
Click to expand...
Click to collapse
Thanks for the help. here is the response. could it be the double .img.img?
10/22/2013 08:35 PM <DIR> .
10/22/2013 08:35 PM <DIR> ..
05/31/2010 01:53 PM 2,540,614 adb.exe
05/31/2010 01:53 PM 96,256 AdbWinApi.dll
05/31/2010 01:53 PM 60,928 AdbWinUsbApi.dll
10/22/2013 05:26 PM 8,634,368 bob.img
12/17/2010 04:45 AM 179,789 fastboot.exe
10/22/2013 08:34 PM 8,634,368 recovery.img.img
10/19/2013 09:58 PM 1,062,273,024 RUU.zip
10/22/2013 03:48 PM 256 Unlock_code.bin
That was it It just flashed!! And that's why you have 700+ thanks. I really appreciate you taking the time to help me.
Rob
Coppo said:
That was it It just flashed!! And that's why you have 700+ thanks. I really appreciate you taking the time to help me.
Rob
Click to expand...
Click to collapse
NP
I am running hboot 1.44, i want to upgrade so i can install newer viper one roms.
I am lost on how to do this.
Here is the process if you are S-Off. If not you need to relock your bootloader before doing fastboot flash firmware.
1 download latest firmware here http://forum.xda-developers.com/showthread.php?t=2182823
2. Put it in your SDK folder together with you ADB.
3. Connect your phone to PC and fire up your ADB
4. Type:
Adb reboot bootloader
(After entering bootloader)
Fastboot devices
(To be sure you are connected)
5. Type
Fastboot oem rebootRUU
(Phone will reboot and silver htc logo will appear.)
6. Type
Fastboot flash zip firmware.zip
Let it process. It will most certain end with FAILED.
7. IMPORTANT: repeat same command again. It will now end with success.
8. End with
Fastboot reboot
All done.
---------- Post added at 10:51 PM ---------- Previous post was at 10:50 PM ----------
Also make sure md5 is correct on the firmware.
I tried to go back to Stock with factory images from Motorola Unlocked. When i try fastboot flash partition gpt.bin it shows Preflash Validation Failed and Failed to erase partition error. I cannot even go into recovery I am stuck anyone please help!.
I am getting Failed to erase partition error when i try to flash anything!.
vignesh245 said:
I tried to go back to Stock with factory images from Motorola Unlocked. When i try fastboot flash partition gpt.bin it shows Preflash Validation Failed and Failed to erase partition error. I cannot even go into recovery I am stuck anyone please help!.
I am getting Failed to erase partition error when i try to flash anything!.
Click to expand...
Click to collapse
If you are in bootloader mode you should be able to get into recovery. Just hit volume down to scroll to recovery and then volume up to select recovery.
---------- Post added at 06:41 PM ---------- Previous post was at 06:40 PM ----------
vignesh245 said:
I tried to go back to Stock with factory images from Motorola Unlocked.
Click to expand...
Click to collapse
Just remember - you cannot downgrade the bootloader or the partition table!!
JulesJam said:
If you are in bootloader mode you should be able to get into recovery. Just hit volume down to scroll to recovery and then volume up to select recovery.
---------- Post added at 06:41 PM ---------- Previous post was at 06:40 PM ----------
Just remember - you cannot downgrade the bootloader or the partition table!!
Click to expand...
Click to collapse
It's not going into recovery or rebooting the only thing I see is the fastboot menu!! What ever I do to flash it says failed to erase partition!! can you tell me why this error in fastboot!
vignesh245 said:
It's not going into recovery or rebooting the only thing I see is the fastboot menu!! What ever I do to flash it says failed to erase partition!! can you tell me why this error in fastboot!
Click to expand...
Click to collapse
What should I do now!! to get my phone back working!
vignesh245 said:
It's not going into recovery or rebooting the only thing I see is the fastboot menu!! What ever I do to flash it says failed to erase partition!! can you tell me why this error in fastboot!
Click to expand...
Click to collapse
well the last guy who got that error had to format his data partition but he had an unlocked bootloader with TWRP and could get into TWRP.
What happens when you connect your phone in bootloader mode to your PC, open a command shell and type:
fastboot devices
Does it return your device's serial number?
---------- Post added at 07:16 PM ---------- Previous post was at 07:15 PM ----------
vignesh245 said:
What should I do now!! to get my phone back working!
Click to expand...
Click to collapse
You should not be trying to flash a lower version of the partition table!!!!
You may have to do a factory reset.
---------- Post added at 07:18 PM ---------- Previous post was at 07:16 PM ----------
vignesh245 said:
I tried to go back to Stock with factory images from Motorola Unlocked. When i try fastboot flash partition gpt.bin it shows Preflash Validation Failed and Failed to erase partition error.
Click to expand...
Click to collapse
gpt.bin is the partition table. If you were trying to flash a lower version partition table than your bootloader version, you cannot do that!!!
What is your bootloader version?
JulesJam said:
well the last guy who got that error had to format his data partition but he had an unlocked bootloader with TWRP and could get into TWRP.
What happens when you connect your phone in bootloader mode to your PC, open a command shell and type:
fastboot devices
Does it return your device's serial number?
---------- Post added at 07:16 PM ---------- Previous post was at 07:15 PM ----------
You should not be trying to flash a lower version of the partition table!!!!
You may have to do a factory reset.
Click to expand...
Click to collapse
Thanks for the reply!!
Yes it returns a Serial number in fastboot! How flash the correct partition?.
vignesh245 said:
Thanks for the reply!!
Yes it returns a Serial number in fastboot! How flash the correct partition?.
Click to expand...
Click to collapse
Is Motorola Device Manager installed on your computer? If not, install it:
https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481
Then connect your phone in fastboot mode to your computer and run MDM and see if MDM can repair your phone.
Also - are you using version 2 of mfastboot to flash?
vignesh245 said:
Thanks for the reply!!
Yes it returns a Serial number in fastboot! How flash the correct partition?.
Click to expand...
Click to collapse
its 60.11
vignesh245 said:
its 60.11
Click to expand...
Click to collapse
I am using normal fastboot ! and I have MDM install will try to repair using MDM !!
vignesh245 said:
its 60.11
Click to expand...
Click to collapse
That is the lollipop 5.0 bootloader. What version of stock were you trying to flash? Kit Kat 4.4.4? If so, that is what happened here - you tried to downgrade the partition table. You cannot downgrade the partition table once you upgrade the bootloader.
---------- Post added at 07:41 PM ---------- Previous post was at 07:40 PM ----------
vignesh245 said:
I am using normal fastboot ! and I have MDM install will try to repair using MDM !!
Click to expand...
Click to collapse
OK let me know how it goes.
JulesJam said:
That is the lollipop 5.0 bootloader. What version of stock were you trying to flash? Kit Kat 4.4.4? If so, that is what happened here - you tried to downgrade the partition table. You cannot downgrade the partition table once you upgrade the bootloader.
---------- Post added at 07:41 PM ---------- Previous post was at 07:40 PM ----------
OK let me know how it goes.
Click to expand...
Click to collapse
Thanks for the clarity in reply!!
Where can i get the stock rom and Files for lolipop 5.0 ?? So I can get back to my stock recovery!
vignesh245 said:
Thanks for the clarity in reply!!
Where can i get the stock rom and Files for lolipop 5.0 ?? So I can get back to my stock recovery!
Click to expand...
Click to collapse
Did MDM not fix your phone? Are you on the XT1095?
http://www.graffixnyc.com/motox.php#
Also, I don't know what build you are, there looks to be more than 1 build for 5.0. Check out the support thread that the link above links too.
JulesJam said:
Did MDM not fix your phone? Are you on the XT1095?
http://www.graffixnyc.com/motox.php#
Also, I don't know what build you are, there looks to be more than 1 build for 5.0. Check out the support thread that the link above links too.
Click to expand...
Click to collapse
MDM did not fix my phone yes I am on Xt1095.
Thanks will try it and let you know
vignesh245 said:
MDM did not fix my phone yes I am on Xt1095.
Click to expand...
Click to collapse
OK, it is probably the custom recovery.
JulesJam said:
OK, it is probably the custom recovery.
Click to expand...
Click to collapse
I am getting Preflash validation failed and I found I have 22.21.11 version installed using MDM. and it says in pink color error in phone as failed to downgrade primary_apt.
Can you help me with this now??
vignesh245 said:
I am getting Preflash validation failed and I found I have 22.21.11 version installed using MDM. and it says in pink color error in phone as failed to downgrade primary_apt.
Can you help me with this now??
Click to expand...
Click to collapse
I would not mess around with the partition table. See if you can do
fastboot format data
fastboot format cache
To wipe your data and cache partitions.
JulesJam said:
I would not mess around with the partition table. See if you can do
fastboot format data
fastboot format cache
To wipe your data and cache partitions.
Click to expand...
Click to collapse
I cannot do that it says the error as in the attached screenshot!
When I select recovery using volume up it says ||boot up failed||
Can Motorola help my situation Mine is a pure edition?
||version downgraded for primary_gpt||
vignesh245 said:
Can Motorola help my situation Mine is a pure edition?|
Click to expand...
Click to collapse
Yes. It is still under warranty. I would get a warranty replacement. If you can't flash anything in BL mode and can't get into recovery and MDM can't repair your phone, idk what else to do.
Motorola should let everyone who unlocks their bootloader know you can't downgrade the bootloader or partition table. They should release the factory images of every version of Android for a device and let people know they have to stick to the version for their bootloader
Quite frankly, this is Motorola's fault for not doing that.
JulesJam said:
Yes. It is still under warranty. I would get a warranty replacement. If you can't flash anything in BL mode and can't get into recovery and MDM can't repair your phone, idk what else to do.
Motorola should let everyone who unlocks their bootloader know you can't downgrade the bootloader or partition table. They should release the factory images of every version of Android for a device and let people know they have to stick to the version for their bootloader
Quite frankly, this is Motorola's fault for not doing that.
Click to expand...
Click to collapse
Thanks a lot will contact motorola get my device replaced !.
vignesh245 said:
I cannot do that it says the error as in the attached screenshot!
When I select recovery using volume up it says ||boot up failed||
Can Motorola help my situation Mine is a pure edition?
||version downgraded for primary_gpt||
Click to expand...
Click to collapse
try using the "erase" command instead of format, I've found on my PC format works, but on Mac I need to use erase.
Although having an unlocked bootloader is useful in many ways like flashing firmware (factory images), installing TWRP and getting root, but it can also lead to blocked services on your device due to security reasons and hence you you might want to relock bootloader to avail those services.
How to Relock Moto G5s Plus Bootloader
Things you need
Minimal ADB Size: 628.5KB
Moto G5s Plus Stock Rom Size: 1.7GB
Steps
Download Moto G5s Plus Stock Firmware from below (in download section).
Install Motorola Driver and ADB Fastboot Driver on your PC.
Now extract stock firmware in ADB Fastboot folder.
Now, turn off your device and boot into bootloader by pressing volume down button +power button simultaneously.
Now, connect your device to your PC via a USB Cable.
Open a command prompt window and type the following commands:
Code:
fastboot oem lock
fastboot oem lock
fastboot flash oem oem.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash system system.img_sparsechunk.4
fastboot flash boot boot.img
fastboot oem lock
Then it will restart your Device. And You Will Get Locked Bootloader.
After locking bootloader, flash full Rom to get OTA. Follow this guide to flash stock firmware - Flash official Firmware Moto G5s Plus
Extra Guides:
[ROOT][TWRP][BOOTLOADER UNLOCK] Moto G5s Plus [sanders]
Remove Unlocked Bootloader Message Moto G5S Plus, G5S
Flash official firmware Moto G5s Plus [sanders]
Appreciate my work?
It is a very hard task to work over mobile data. Please consider making a donation If this guide helped you.
Bank Transfer: Name- Shubham Mishra, A/C no. 8756149523, IFSC code. AIRP0000001
Paypal https://paypal.me/shubhmishra
You are doing a great job bro......:good::fingers-crossed:
shu006 said:
Although having an unlocked bootloader is useful in many ways like flashing firmware (factory images), installing TWRP and getting root, but it can also lead to blocked services on your device due to security reasons and hence you you might want to relock bootloader to avail those services.
How to Relock Moto G5s Plus Bootloader
Things you need
Minimal ADB Size: 628.5KB
Moto G5s Plus Stock Rom Size: 1.7GB
Steps
Download Moto G5s Plus Stock Firmware from below (in download section).
Install Motorola Driver and ADB Fastboot Driver on your PC.
Now extract stock firmware in ADB Fastboot folder.
Now, turn off your device and boot into bootloader by pressing volume down button +power button simultaneously.
Now, connect your device to your PC via a USB Cable.
Open a command prompt window and type the following commands:
Code:
fastboot oem lock
fastboot oem lock
fastboot flash oem oem.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash system system.img_sparsechunk.4
fastboot flash boot boot.img
fastboot oem lock
Then it will restart your Device. And You Will Get Locked Bootloader.
After locking bootloader, flash full Rom to get OTA. Follow this guide to flash stock firmware - Flash official Firmware Moto G5s Plus
Extra Guides:
[ROOT][TWRP][BOOTLOADER UNLOCK] Moto G5s Plus [sanders]
Remove Unlocked Bootloader Message Moto G5S Plus, G5S
Flash official firmware Moto G5s Plus [sanders]
Appreciate my work?
It is a very hard task to work over mobile data. Please consider making a donation If this guide helped you.
Bank Transfer: Name- Shubham Mishra, A/C no. 8756149523, IFSC code. AIRP0000001
Paypal https://paypal.me/shubhmishra
Click to expand...
Click to collapse
didn't work
saying to allow oem unlocking but it is disabled by saying already unlocked
Its also not work here. Need a signed firmware and this is not signed from Motorola.
Gesendet von meinem Moto G (5S) Plus mit Tapatalk
flashing boot.img error
Image signed with key bad key
Working ????
is the method working ????
Please wait 2 days. I am busy due to sister's engagement. I'll fix all issues asap.
Not Worked
Hey man it didnt work !!!it said wrong key/bad key and was stuck on bootlogo had to flash stock rom again
Yes this just creates a bootloop unfortunately
We need a signed rom from Motorola.
I was able to block Bootloader :fingers-crossed:
Laercio_lalau said:
I was able to block Bootloader :fingers-crossed:
Click to expand...
Click to collapse
How did you get past the unsigned error?
katienugget said:
How did you get past the unsigned error?
Click to expand...
Click to collapse
I'll post it soon as I did.
any update with this. I would love to relock my device considering everything else i have tried doesnt work well.
You put 4 steps on sparsechunk, but the rom has 5 sparechunk steps.
is correct to flash till step four only?
Anyway I got this message:
Shu006>mfastboot oem lock
...
(bootloader) Still require signed boot.img
OKAY [ 0.016s]
finished. total time: 0.016s
jefpcbr said:
You put 4 steps on sparsechunk, but the rom has 5 sparechunk steps.
is correct to flash till step four only?
Anyway I got this message:
Shu006>mfastboot oem lock
...
(bootloader) Still require signed boot.img
OKAY [ 0.016s]
finished. total time: 0.016s
Click to expand...
Click to collapse
Yup I got that I want to relock my bootloader but stuck at this.
????...help me out anyone please
---------- Post added at 07:10 PM ---------- Previous post was at 07:09 PM ----------
Laercio_lalau said:
I'll post it soon as I did.
Click to expand...
Click to collapse
please post it soon ..many days has passed but you still didn't Posted,???
maaze790 said:
Yup I got that I want to relock my bootloader but stuck at this.
????...help me out anyone please
---------- Post added at 07:10 PM ---------- Previous post was at 07:09 PM ----------
please post it soon ..many days has passed but you still didn't Posted,???
Click to expand...
Click to collapse
Already forgotten ... take this file. bat and place next to Firmware extracted from 2 click on the .bat file and wait for the procedure to finish, if it fails to start the system, reinstall the Firmware again.
Sorry for bad English.
Link:https://mega.nz/#!hgFHTQIb!KWggcvjA0mk8e-M0dPLX0psiiwE4ikcLS4at6mzsZGw
---------- Post added at 07:34 PM ---------- Previous post was at 07:30 PM ----------
Laercio_lalau said:
Already forgotten ... take this file. bat and place next to Firmware extracted from 2 click on the .bat file and wait for the procedure to finish, if it fails to start the system, reinstall the Firmware again.
Sorry for bad English.
Link:https://mega.nz/#!hgFHTQIb!KWggcvjA0mk8e-M0dPLX0psiiwE4ikcLS4at6mzsZGw
Click to expand...
Click to collapse
Bootloader is Blocked, but Software appears modified, this I could not solve ,,, if someone has the solution, it would be good
Lol this bat is not for g5s plus. G5s have 5 sparsechunk and not 4.
Laercio_lalau said:
Already forgotten ... take this file. bat and place next to Firmware extracted from 2 click on the .bat file and wait for the procedure to finish, if it fails to start the system, reinstall the Firmware again.
Sorry for bad English.
Link:https://mega.nz/#!hgFHTQIb!KWggcvjA0mk8e-M0dPLX0psiiwE4ikcLS4at6mzsZGw
---------- Post added at 07:34 PM ---------- Previous post was at 07:30 PM ----------
Bootloader is Blocked, but Software appears modified, this I could not solve ,,, if someone has the solution, it would be good
Click to expand...
Click to collapse
How you relocked bootloader will you please tell me
---------- Post added at 07:58 PM ---------- Previous post was at 07:49 PM ----------
Laercio_lalau said:
Already forgotten ... take this file. bat and place next to Firmware extracted from 2 click on the .bat file and wait for the procedure to finish, if it fails to start the system, reinstall the Firmware again.
Sorry for bad English.
Link:https://mega.nz/#!hgFHTQIb!KWggcvjA0mk8e-M0dPLX0psiiwE4ikcLS4at6mzsZGw
---------- Post added at 07:34 PM ---------- Previous post was at 07:30 PM ----------
Bootloader is Blocked, but Software appears modified, this I could not solve ,,, if someone has the solution, it would be good
Click to expand...
Click to collapse
Are you sure that helped you to relock your bootloader
maaze790 said:
How you relocked bootloader will you please tell me
---------- Post added at 07:58 PM ---------- Previous post was at 07:49 PM ----------
Are you sure that helped you to relock your bootloader
Click to expand...
Click to collapse
Yes, you can edit the .bat file and put line 5, I did not do it because I'm using root ...