Database Develop

[Q] recovery mode problems with cache

whenever i go into recovery mode i get an error on the bottom of the screem
BUILD : RA-dream-v1.7.0
E:Error in CACHE:recovery/log
(No Space left on device)
i cant nand backup or anything

rickyiswhite said:
whenever i go into recovery mode i get an error on the bottom of the screem
BUILD : RA-dream-v1.7.0
E:Error in CACHE:recovery/log
(No Space left on device)
i cant nand backup or anything
Click to expand...
Click to collapse
There are two possibilities:
1) The log is occupiing really the whole space on cache. In that case try to remove the log file from cache directory
2) Did you mess up with custom partion tables? To me this happened some time ago when I forgot to flash fr_boot_xxx.zip onto a boot.img while having installed custom partitions. In that case you have to clean everything. Eventually you need also to flash recovery again. If you have a recent backup, you can try to do a
fastboot erase system -w
then boot into recovery and see, if everything works for you again. If not you need to flash a new recovery:
fastboot flash recovery recovery.img
After that everything should work again, i.e. you can install your backup or you can install a new ROM.

AndDiSa said:
There are two possibilities:
1) The log is occupiing really the whole space on cache. In that case try to remove the log file from cache directory
2) Did you mess up with custom partion tables? To me this happened some time ago when I forgot to flash fr_boot_xxx.zip onto a boot.img while having installed custom partitions. In that case you have to clean everything. Eventually you need also to flash recovery again. If you have a recent backup, you can try to do a
fastboot erase system -w
then boot into recovery and see, if everything works for you again. If not you need to flash a new recovery:
fastboot flash recovery recovery.img
After that everything should work again, i.e. you can install your backup or you can install a new ROM.
Click to expand...
Click to collapse
hmm ok ill try that... thanks... and sometimes it says cant open cache or something

RECOVERY - postrecoveryboot.sh - ERROR: 2

Google has no answer for me.
Every time I enter into the recovery and push the message button I get this ERROR: 2.
Everything works fine, its latest TWRP 3.0.2.
Could you tell me something about this error message 2?
What is 'postrecoveryboot.sh'?
How can I get this red message off / without error?
thanx in advance

How do I edit my boot script?

MichaBit said:
Google has no answer for me.
Every time I enter into the recovery and push the message button I get this ERROR: 2.
Everything works fine, its latest TWRP 3.0.2.
Could you tell me something about this error message 2?
What is 'postrecoveryboot.sh'?
How can I get this red message off / without error?
thanx in advance
Click to expand...
Click to collapse
Hi,
I have the same problem. Also on TWRP 3.0.2. and everything seems to work.
Can't find anything about this 'postrecoveryboot.sh' Error 2.
Did you find a solution in the meantime?
Thanks for any help in advance.

Arninho said:
Did you find a solution in the meantime?
Click to expand...
Click to collapse
No, unfortunately not.
If XDA has no solution, who else?

I have the same problem, this is inside the file
Code:
#!/sbin/sh
# Include device-specific vars
source /sbin/bootrec-device
# Turn the LED off
echo 0 > ${BOOTREC_LED_RED}
echo 0 > ${BOOTREC_LED_GREEN}
echo 0 > ${BOOTREC_LED_BLUE}
that error is because this file bootrec-device located at sbin folder always missing when reboot system or recovery
I have try many way
-flash stock rom with flashtool
-flash rom via recovery
-wipe via adb and fastboot
-chmod this file bootrec-device to read only
-remove this file postrecoveryboot.sh just come back after reboot recovery
all that way doesn't work
my Xperia unable to boot right know :crying:
maybe i'll try search what's file that create this??? postrecoveryboot.sh
where's boot script locate???
any help would be apreciated

InAMovies said:
my Xperia unable to boot right know :crying:
Click to expand...
Click to collapse
Thanks for that much information. :good:
A possible 'emergency solution' so that your device reboots again could be attached link.
What really surprised me, no one else has this ERROR: 2, and if not, why not?
http://www.flashtool.net/index.php

You can fix this 'postrecoveryboot.sh' Error 2 with a lower version twrp
I use twrp 2.8.7 which has been uploaded by someone from here androidfilehost.com/?fid=24052804347811669
flash with "fastboot flash boot boot.img" only if you UB, on LB try downgrade your twrp version
and then via file manager, just chmod the file bootrec-device located at sbin folder with read only access
my phone can only be booted only with rom existenz, and it was frequently rebooted and my battery status is unclear, sometimes 65% during the initial boot, and then only a 5% reboot afterwards
I have flash using flashtool with many based rom from 10.5.1.A, 10.6.1.A, 10.7.1.A latest, but it still does not make my phone work just to show sony screen flickered and died with the indicator is still red
all the problems occurred after I had this problem 'postrecoveryboot.sh' Error 2
I still do not know how to turn off the script, when I delete the file after reboot definitely go back there
hoping my phone can be normal again sometime

InAMovies said:
I still do not know how to turn off the script, when I delete the file after reboot definitely go back there
Click to expand...
Click to collapse
Could the cause for the error be a kind of provider branding?
So deeper implemented than the usual firmware.
My device was delivered via German Telekom.

[B]Solution![/B]
After installing Multirom v33 the error message is gone!
Dont ask why, both recoverys, the new one into the FOTA partition from attached link und the older, normal one 3.0.2.0 are error-free! :good:
https://forum.xda-developers.com/xperia-z/orig-development/mod-multirom-v33x-xperia-z-t3432385

I have installed the Modified recovery FOTA, before this error happen all working fine any custom rom working
but after this error, i can boot into recovery and install rom then reboot got bootloop, charger just show blip screen logo
just wanna try your idea with the Multirom v33 non modified

MichaBit said:
Google has no answer for me.
Every time I enter into the recovery and push the message button I get this ERROR: 2.
Everything works fine, its latest TWRP 3.0.2.
Could you tell me something about this error message 2?
What is 'postrecoveryboot.sh'?
How can I get this red message off / without error?
thanx in advance
Click to expand...
Click to collapse
Can You be so Kind to tell me how to flash in the correct way the latest version of TWRP with no error? Thank You very much!!

Ricky_Karmator said:
Can You be so Kind to tell me how to flash in the correct way the latest version of TWRP with no error? Thank You very much!!
Click to expand...
Click to collapse
Download latest recovery 'twrp-3.0.2-0-yuga.img' from link 1.
Put it to your Phone, turn of, push volume + and insert USB-cable for flashmode.
Blue LED-light appears.
Type -fastboot flash boot boot.img
-fastboot reboot
in ADB-connection CMD on your PC --> thats all.
Optional you can use the Tool in link 2.
*Flashing recovery successfully*
https://dl.twrp.me/yuga/
https://twrp.me/app/

MichaBit said:
Download latest recovery 'twrp-3.0.2-0-yuga.img' from link 1.
Put it to your Phone, turn of, push volume + and insert USB-cable for flashmode.
Blue LED-light appears.
Type -fastboot flash boot boot.img
-fastboot reboot
in ADB-connection CMD on your PC --> thats all.
Optional you can use the Tool in link 2.
*Flashing recovery successfully*
https://dl.twrp.me/yuga/
https://twrp.me/app/
Click to expand...
Click to collapse
I wa sure to copy the .img file in "platform-tools" folder in my PC and with cmd type "-fastboot flash boot boot.img" and not to have the file inside the internal memory of my Xperia Z. Obviously i think to rename "Twrp-3.0.blablabla" into boot.img

Ricky_Karmator said:
I wa sure to copy the .img file in "platform-tools" folder in my PC and with cmd type "-fastboot flash boot boot.img" and not to have the file inside the internal memory of my Xperia Z. Obviously i think to rename "Twrp-3.0.blablabla" into boot.img
Click to expand...
Click to collapse
Yes, very correct, copy and rename the file into 'boot.img' to your ADB-folder and flash it. :angel:

Finally with some free time i unlocked and flash the latest TWRP on my old Xperia Z. And yes i've got the same error "ERROR: 2". But everything works from backup to restore and flash Custom ROM. So i think we can nevermind about that

I have the same.
Sometimes my phone randomly reboot, and seems to be some app cause this reboots.
It was happend more and more often. And suddenly couple days ago my phone start to bootloop (just endlesly booting at xperia logo).
I have F5121 stock 8.0 Oreo and done all like in this manual https://forum.xda-developers.com/t/...els-latest-34-4-a-2-118-25-sept-2018.3594502/
So I was have rooted kenrnel twrp 3.2.3.0+DRM-Fix +magisk +FCS_1.3 +debloat script.
Almost 2 years of no problems and this surprise.
When I load to twrp and press menu button i see this:
Updating partition details...
...done
Unable to mount storage
So I was trying do backup of all partitions and after that I go in in wipe menu => advanced wipe => checkbox cache partition => fix patition
than I try to fix all patitions - it doesn't help.
So I do this:
wipe menu => advanced wipe => checkbox data partition => change to exFAT filesystem then => change back to EXT4 filesystem and restore data from backup. And do system/data partitions
and try to restore my backup - and it don't work.
EVEN my older backups don't works - I always become bootloop on xperia logo.
When I download twrp backup to PC and unpack cache.ext4.win\recovery I see file with name last_log.
Thats how last strings of file last_log look like:
~
ro.bootimage.build.date.utc=1533015130
ro.bootimage.build.fingerprint=Sony/omni_suzu/suzu:8.1.0/OPM4.171019.021.R1/4:eng/test-keys
ro.bootloader=s1
ro.debuggable=1
ro.property_service.version=2
init.svc.adbd=running
init.svc.ueventd=running
init.svc.recovery=running
init.svc.ldconfigtxt=stopped
init.svc.set_permissive=stopped
twrp.crash_counter=0
keyguard.no_require_sim=true
tombstoned.max_tombstone_count=50
Running boot script...
I:/sbin/postrecoveryboot.sh process ended with RC=0
Done.
I would like to hear some ideas why that may happen (Unable to mount storage). Coz i lost part of my data and don't wanna have the same experience again and again in future.

Can't get out of Fastboot.

"Cyanogendmod.Org / Install CM for z3c / Unlock Your Xperia Z3 Compact" <--- That's the URL somehow.
Followed this instruction. Got myself the 12.1 .zip and .img.
I get error installaing the .zip and the .img isn't even an option:
The old rom is infinitly loading in that blue/purple wave line.
I then turn the phone off by holding down the power button until the phone restarts.
My history:
>Pressing up and down on the button rockers.
>Cyanogen Recovery starts.
>I choose "Wipe data/factory reset".
>I choose "Apply update".
(Apply from ADB doesn't work as it seems as ADB has no access for USB debugging. That's why install it from an external SD)
>Install "cm-12.1-20160918-NIGHTLY-z3c.zip" or its copy that I named "update.zip".
Error message:
[CAN'T POST PICTURE BECAUSE XDA HAS VERY FUNNY MEME RULES XDDD]
Private message maybe...? Can I send you guys URL pics via PM?
How can I get out of this loop?

If you want to go back to stock, use flashtool and flash whatever version you want (FTF method), I had an issue with flashing CM too, it said this is for aries but this device is z3c etc. Is this your problem?

marshalpear said:
If you want to go back to stock, use flashtool and flash whatever version you want (FTF method), I had an issue with flashing CM too, it said this is for aries but this device is z3c etc. Is this your problem?
Click to expand...
Click to collapse
I definitly want CyanogenMod 12.1 on my Z3C. Is it still possible?
I hope you can decypher the URL h t t p : / / t i n y u r l . c o m / j 6 4 u 8 u a

Few things you can do:
1- Download the ROM again, might be corrupted download.
2- Flash Lollipop FTF(not necessary), Flash TWRP recovery, boot into recovery, (If it asks, swipe to allow modifications to system), wipe everything (system,cache,dalvik,data), flash the ROM through TWRP recovery.
3- If it gives the error that I talked about in my first message, let me know.

marshalpear said:
Few things you can do:
1- Download the ROM again, might be corrupted download.
2- Flash Lollipop FTF(not necessary), Flash TWRP recovery, boot into recovery, (If it asks, swipe to allow modifications to system), wipe everything (system,cache,dalvik,data), flash the ROM through TWRP recovery.
3- If it gives the error that I talked about in my first message, let me know.
Click to expand...
Click to collapse
I tried #1 but I'm already stuck with the "SONY XPERIA" blackscreen at the very beginning when booting the smartphone. I suppose it's because of the failed installation and the not choosing of "Wipe clean/factory reset".
I hope that still doesn't count as bricking. I let the accumulator run dry and reload the battery and try to get into the Cyanogenmod Recovery again. Right now nothing is possible. =/
I hope that doesn't count as bricking. If so: These special OTG USB thingies fix a lot I heard, should I get myself one?

SYLVER SECOND said:
I tried #1 but I'm already stuck with the "SONY XPERIA" blackscreen at the very beginning when booting the smartphone. I suppose it's because of the failed installation and the not choosing of "Wipe clean/factory reset".
I hope that still doesn't count as bricking. I let the accumulator run dry and reload the battery and try to get into the Cyanogenmod Recovery again. Right now nothing is possible. =/
I hope that doesn't count as bricking. If so: These special OTG USB thingies fix a lot I heard, should I get myself one?
Click to expand...
Click to collapse
If you are on CM recovery, then there is the problem. AFAIK you can't flash anything through that, so you have to push TWRP on your device using fastboot and then flash AOSP/CM rom you want.

SYLVER SECOND said:
I tried #1 but I'm already stuck with the "SONY XPERIA" blackscreen at the very beginning when booting the smartphone. I suppose it's because of the failed installation and the not choosing of "Wipe clean/factory reset".
I hope that still doesn't count as bricking. I let the accumulator run dry and reload the battery and try to get into the Cyanogenmod Recovery again. Right now nothing is possible. =/
I hope that doesn't count as bricking. If so: These special OTG USB thingies fix a lot I heard, should I get myself one?
Click to expand...
Click to collapse
That's called a soft-brick. You should install the ADB drivers for your phone on your PC and then download TWRP for your phone (.img file) and rename the TWRP you downloaded to recovery.img .
You should put the recovery.img into the folder where your ADB drivers are installed, then Shift + RClick on that folder then select Open Command Window Here. Connect your phone in fastboot mode to your PC (Keep Vol. Up button then plug in your device). Type the following commands:
fastboot flash boot recovery.img
fastboot reboot
If you've done it all correctly, your phone should boot into TWRP recovery. From there you should go to wipe-advanced wipe and wipe your Cache,Dalvik Cache, System, Boot. DO NOT REBOOT NOW. You should go back to main menu and choose install, then choose the ROM you want to install. It should flash it if you don't have a corrupted file. After flashing, you can safely reboot your phone, don't forget to flash GApps if you want Google features on your Cyanogen, hope I helped!

More info about my error:
h t t p : / / t i n y u r l . c o m / z b e v y u 2
Each version of step #3 doesn't work. Still trying to figure out how to get TWRP...

marshalpear said:
That's called a soft-brick. You should install the ADB drivers for your phone on your PC and then download TWRP for your phone (.img file) and rename the TWRP you downloaded to recovery.img .
You should put the recovery.img into the folder where your ADB drivers are installed, then Shift + RClick on that folder then select Open Command Window Here. Connect your phone in fastboot mode to your PC (Keep Vol. Up button then plug in your device). Type the following commands:
fastboot flash boot recovery.img
fastboot reboot
If you've done it all correctly, your phone should boot into TWRP recovery. From there you should go to wipe-advanced wipe and wipe your Cache,Dalvik Cache, System, Boot. DO NOT REBOOT NOW. You should go back to main menu and choose install, then choose the ROM you want to install. It should flash it if you don't have a corrupted file. After flashing, you can safely reboot your phone, don't forget to flash GApps if you want Google features on your Cyanogen, hope I helped!
Click to expand...
Click to collapse
K, 90% of this works. I got the TWRP "app" and I cleaned the cache and all that, but I had to reboot. You see:
To transfer new media I need to remove my external SD from the z3c to my old LG. The LG is connected with my PC and is therefore a kind of card-reader. I tried 2 different nightly thingies.
I still get extraction errors, see:
h t t p : / / t i n y u r l . c o m / h j j d 4 o b
I downloaded 2 different nightlies 6 times already. I dunno. Somethings off here.
Also: For what is the recovery.img? Should I install it afterwards?
I have to restart the phone in order to replug the SD card and get recognigzed by the TWRP.
I did everything from this:
http://forum.xda-developers.com/showthread.php?t=2522762
Because of Error 7.
Now I get Error 6.....

SYLVER SECOND said:
K, 90% of this works. I got the TWRP "app" and I cleaned the cache and all that, but I had to reboot. You see:
To transfer new media I need to remove my external SD from the z3c to my old LG. The LG is connected with my PC and is therefore a kind of card-reader. I tried 2 different nightly thingies.
I still get extraction errors, see:
h t t p : / / t i n y u r l . c o m / h j j d 4 o b
I downloaded 2 different nightlies 6 times already. I dunno. Somethings off here.
Also: For what is the recovery.img? Should I install it afterwards?
I have to restart the phone in order to replug the SD card and get recognigzed by the TWRP.
I did everything from this:
http://forum.xda-developers.com/showthread.php?t=2522762
Because of Error 7.
Now I get Error 6.....
Click to expand...
Click to collapse
OK, your problem is that you messed up your system, so wiping it is not gonna solve this issue. You need to download a stock firmware file (an FTF file) and flash it through Flashtool, because your device name seems to be "." which is why you were getting "error 7". As for the recovery.img, you will use it to flash TWRP recovery on your phone. TWRP app doesn't work correctly if you don't flash it to your recovery partition so do as follows:
1- Download Flashtool, install the drivers of your device for Flashtool (you can search it on xda forums), download an FTF file, any of them should do, but as you will install CM 12.1, I recommend a Lollipop FTF.
2- Flash the firmware through Flashtool. This will turn your phone into a stock one. Unlock your bootloader if you haven't already, which I believe you have.
3- Flash the TWRP recovery through fastboot (follow my earlier instructions)
4- After you open TWRP recovery do the wipes, note that you can still connect your phone to your computer for file transfers in TWRP Recovery.
5- Install the CM zip file through recovery
IF YOU GET ERROR 7 SAYING :this package is for device: D5803, D5833, z3c; this device is aries.
7- Open the CM 12.1 zip file on your computer and proceed to META-INF/com/google/android directory.
8- In that folder you should see "updater-script", extract it to somewhere and open it with Notepad.
9- Once you open it press Ctrl + H to change some of the lines.
10- Write "D5833" without the quotation marks in the first space and write "aries" without the quotation marks into the second space and click replace all.
(This will change all "D5833" to "aries" in the file therefore making it usable for your device) Save the file and put it into the directory of where you found it, replace it with the original.
11- Now put the edited .zip file into your phone storage, and flash it through recovery. It should work. :good:

marshalpear said:
3- Flash the TWRP recovery through fastboot (follow my earlier instructions)
Click to expand...
Click to collapse
I think he shouldn't flash TWRP on boot partition, as you wrote. That might cause further issues. I am flashing my recovery through fastboot without problems using next command:
fastboot flash recovery recovery.img

Cirra92 said:
I think he shouldn't flash TWRP on boot partition, as you wrote. That might cause further issues. I am flashing my recovery through fastboot without problems using next command:
fastboot flash recovery recovery.img
Click to expand...
Click to collapse
It won't matter. Because when he flashes the CM, it'll flash the CM Recovery along with it.

marshalpear said:
It won't matter. Because when he flashes the CM, it'll flash the CM Recovery along with it.
Click to expand...
Click to collapse
Yea I know, but before that, he needs to have a working TWRP on right partition to be able to even flash any rom.

Cirra92 said:
Yea I know, but before that, he needs to have a working TWRP on right partition to be able to even flash any rom.
Click to expand...
Click to collapse
That's why I wrote those steps for him/her to follow. If you flash TWRP to boot partition, when you boot the phone, it will go straight into TWRP. If you flash it to recovery partition, you'll have to boot it manually.

marshalpear said:
That's why I wrote those steps for him/her to follow. If you flash TWRP to boot partition, when you boot the phone, it will go straight into TWRP. If you flash it to recovery partition, you'll have to boot it manually.
Click to expand...
Click to collapse
Logical step, didn't think about it that way, I assumed OP knew how to enter recovery

"1- Download Flashtool, install the drivers of your device for Flashtool (you can search it on xda forums), download an FTF file, any of them should do, but as you will install CM 12.1, I recommend a Lollipop FTF.
2- Flash the firmware through Flashtool. This will turn your phone into a stock one. Unlock your bootloader if you haven't already, which I believe you have.
3- Flash the TWRP recovery through fastboot (follow my earlier instructions)
4- After you open TWRP recovery do the wipes, note that you can still connect your phone to your computer for file transfers in TWRP Recovery.
5- Install the CM zip file through recovery
IF YOU GET ERROR 7 SAYING :this package is for device: D5803, D5833, z3c; this device is aries.
7- Open the CM 12.1 zip file on your computer and proceed to META-INF/com/google/android directory.
8- In that folder you should see "updater-script", extract it to somewhere and open it with Notepad.
9- Once you open it press Ctrl + H to change some of the lines.
10- Write "D5833" without the quotation marks in the first space and write "aries" without the quotation marks into the second space and click replace all.
(This will change all "D5833" to "aries" in the file therefore making it usable for your device) Save the file and put it into the directory of where you found it, replace it with the original.
11- Now put the edited .zip file into your phone storage, and flash it through recovery. It should work."
K, so I guess I'm finished with #1 and #2. Sorry, had a ****-ton of chores to do. Before I progress, I wanted to send you guys
this pic:
https://img3.picload.org/image/rdricord/unbenannt.png
Is the root access necessary, or can I progress?
That's the sites I've used, if anybody wonders why something is the way it is right now:
http://forum.xda-developers.com/z3-compact/general/list-stock-firmwares-d5803-d5833-t2906706
http://forum.xda-developers.com/showpost.php?p=66275965&postcount=2029
http://forum.xda-developers.com/showpost.php?p=60001557&postcount=829
Von "Sony Mobile Flasher by Androxyde":
"23/023/2016 22:23:52 - INFO - Root access denied
23/024/2016 22:24:07 - ERROR - Illegal key size or default parameters
23/024/2016 22:24:12 - ERROR - Illegal key size or default parameters
23/024/2016 22:24:13 - WARN - Please check your Phone and 'ALLOW' Superuseraccess!
23/024/2016 22:24:14 - INFO - Root access denied"

FlashTool says the firmware has been flashed so I don't understand what are you trying to do after that? After flashing the FTF file you should flash TWRP through "FASTBOOT". Then follow the instructions.

K, did everything you said. Read everything five-times. Replaced "D5833" to "aries" and all that stuff. Still getting ERROR 7.
The phone is still in TWRP Recovery from FASTBOOT / BOOTLOAD because I "constantly" charge it to stay in recovery. If I had found this Mount option earlier... kinda feel stupid for that. So I still get ERROR 7. I copied the modified .zip to internal storage and SD card to see if I get the same error twice. And yeah.
Exact error message in red letters:
"Updater process ended with ERROR: 7
Error installing zip file ' /external-sd/cm-12.1-20160918-NIGHTLY-z3c.zip'
Updating partition details...
... done"
So I forethought and cleaned the cache and need somewhat new instructions.
Also:
I suppose with "Advanced Wipe" and your instructions you meant this points, right?:
http://tinyurl.com/jc5rv3a

SYLVER SECOND said:
K, did everything you said. Read everything five-times. Replaced "D5833" to "aries" and all that stuff. Still getting ERROR 7.
The phone is still in TWRP Recovery from FASTBOOT / BOOTLOAD because I "constantly" charge it to stay in recovery. If I had found this Mount option earlier... kinda feel stupid for that. So I still get ERROR 7. I copied the modified .zip to internal storage and SD card to see if I get the same error twice. And yeah.
Exact error message in red letters:
"Updater process ended with ERROR: 7
Error installing zip file ' /external-sd/cm-12.1-20160918-NIGHTLY-z3c.zip'
Updating partition details...
... done"
So I forethought and cleaned the cache and need somewhat new instructions.
Also:
I suppose with "Advanced Wipe" and your instructions you meant this points, right?:
http://tinyurl.com/jc5rv3a
Click to expand...
Click to collapse
OK, so try flashing TWRP to recovery partition to get you out of TWRP after you boot by writing these commands in the ADB:,
fastboot flash recovery recovery.img
fastboot reboot recovery
This will flash the TWRP to recovery partition and will boot you into TWRP. As you do this you won't have a go at the recovery again but for this time. You can reach the TWRP by pressing the Vol. Down button when the phone vibrates at the boot. Also if you want to force shutdown your phone you can use Vol. Up + Power Button combination for a few secs.

marshalpear said:
OK, so try flashing TWRP to recovery partition to get you out of TWRP after you boot by writing these commands in the ADB:,
fastboot flash recovery recovery.img
fastboot reboot recovery
This will flash the TWRP to recovery partition and will boot you into TWRP. As you do this you won't have a go at the recovery again but for this time. You can reach the TWRP by pressing the Vol. Down button when the phone vibrates at the boot. Also if you want to force shutdown your phone you can use Vol. Up + Power Button combination for a few secs.
Click to expand...
Click to collapse
K, cool feature. Got it all set up now, but back to the main subject:
Is it even possible to install CyanogenMod 12.1 on Sony Z3C?

[CLOSED]Vivo XL2 TWRP 3.0 and Root

I must note: I use linux. I only used Windows because SPFT Linux version gave me a chip mismatch error I couldn't fix easily.
1: Please read. It explains what problems might arise. Especially post #6 and #13.
2: There are 2 versions of the scatter file. The MT6735 version is what I used successfully. The MT6737Tmod version is what comes from post #6 & #13.
3: Please use each scatter file to Readback your boot and recovery partitions first, renaming as fit, so you can have a backup BEFORE ANYTHING. Then test unpacking them to see if everything went correctly. Then readback every partition in the scatter file so you don't have to depend on the stock ROM for a backup. I didn't and it led me to take this route.
3: Seem to be a difference in the naming of the scatter file and sizes of system, cache, and userdata inside from the stock ROM and what works..
4: DO NOT choose Format+Download until you know which scatter file works, unless you want to chance a Hard Brick.
5: Wiping the dalvik and cache in stock recovery before flashing TWRP seems to be the best thing to do to avoid boot loops or a hung boot.
THIS ROOT PROCESS WAS DONE OVER THREE DAYS OF CAR WORK, DRIVING, FAMILY, AND COMPUTER WORK. MOST OF THE TIME SPENT WAS THIS MORNING TRYING TO GO TO SLEEP. DIDN'T HAVE TIME TO DOCUMENT AND TAKE PICTURES. THIS WRITE-UP IS FROM WHAT I REMEMBER DURING THIS PROCESS. IF I CAN REMEMBER SOME VAGUE DETAIL THAT YOU NEED, GOOD. IF NOT, DON'T STRESS ME. THE HARD PART IS DONE. A GOOGLE SEARCH OF SOME OF THESE PROGRAMS WILL GET QUICKER RESULTS IF YOU DON'T HAVE THEM. THE MAIN THING NEEDED FROM MY RESEARCH WAS THE SCATTER FILE. LINKS FOR SCATTER FILE AND RECOVERY IMAGE ARE BELOW.
Looking for a way to root first day getting this phone in February. Read this post last Tuesday about MT67xx rooting, thanks lsemprini. Spent two days finding which versions of the programs work with this phone, already had the ROMs, drivers, and tools. Dove right in.
I downloaded the ROM from needrom. Scatter file was unusable. Wrong chip error. Phone reads MT6735 scatter file read MT6737. Did a manual diff. Used SP Flash Tool v5.1524 to flash, formatted instead of downloading by mistake, cord got pulled, Hard brick. Fought with Windows7 to get drivers to recognize a hard brick. Still don't know how I did it but it read then flashed. Looked like another hard brick but SPFT would recognize it for the Memory Test. I just held power+vol_down with just charging block power to get it to come on. Sometimes just one of the buttons was enough to get it to power on and start a bootloop. Took two minutes sometimes. Flashing the wrong recovery led to bootloops. Starting SP Flash Tool and plugging in the USB to the phone as soon as it powers off during a loop will let the preloader "register" and the images to be flashed. Flashing from a stock ROM will lead to IMEI being erased. Used SN Write Tool v1.1716 to write the IMEI numbers. Got them from the side of the box. The MD1_DB and AP_DB files needed are in the stock rom.
Ported TWRP, credit to jemmini for the post https://forum.xda-developers.com/vivo-xl/development/recovery-t3311601. Used that recovery as a base. Ported according to the myriad of guides that I have been reading over the past few days. None of them worked as instructed, had to modify trial and error style. Finally got TWRP to read the internal partitions AND remain after a reboot. A lot was going on when I did this. Not sure if I formatted before, I remember flashing a lot of because of something. I mounted the system just in case & flashed SuperSu from chainfire's website, no formatting afterwards. Rebooted and installed SuperUser and BusyBox. I tried adb and fastboot. They work but not for everything. Hooked phone up to computer with debugging enabled.
Code:
adb root
gives a shell, no errors unlike before. Edit: ADB won't let me start as root anymore.
Needed files
Blu Vivo XL2 TWRP 3 Recovery
MT6735 Scatter File
MT6737T Scatter File
BLU Vivo XL2 V0070UU Stock ROM if you don't have a backup of your partition images.
Step 1
Install Minimal ADB and Fastboot and USB VCOM drivers.
Download SP Flash Tool, SN Write Tool, scatter file, and twrp3.0 to a working folder.
Download SuperSu zip & SuperUser apk then put them on your SD Card.
Install SD card into phone.
Step 1.A For Full ROM Flash and IMEI Write
Download Stock ROM and extract to working folder.
Move twrp3.0 to ROM folder.
Step 2
Install SP Flash Tool and SN Write Tool and run.
Step 3 To flash TWRP only
Reboot phone to recovery then wipe cache and dalvik. Can't remember if it is a dalvik option in the stock recovery now.
Power off phone. Make sure it is not plugged up to the computer.
IN SP Flash Tool:
Load scatter file that works from working folder.
Make sure download only is selected in drop down menu.
Check only the recovery partition box and click the name of the recovery file on the same line.
Browse to TWRP recovery image and select.
Click the Download button with the green arrow.
Plug phone into computer and wait until window with OK pops up. Success.
Step 3.B OPTIONAL
Select format and flash all using stock ROM or images backed up from your phone.
Stock ROM must be extracted and custom recover put into same folder and renamed to "recovery.img" to make
everything automatically load.
Click the Download button with the green arrow.
Plug phone into computer and wait until window with OK pops up. Success
Step 4 Only needed when formating+downloading ROM
With phone still powered off and unplugged, write IMEI numbers using SN Write Tool.
Step 4.A
Click System Config.
Select IMEI in Write Option Area.
Make sure IMEI Checksum and Dual IMEI are checked.
Load MD1_DB and AP_DB files from ROM folder.
Click Load Modem DB from DUT box.
Click Save.
Step 4.B
Click Start.
Input your IMEI numbers from box.
Click OK. Success
Step 5
Boot to recovery.
Swipe to make permanent.
Wipe dalvik and cache.
Flash SuperSu..
Reboot.
Install SuperUser apk and BusyBox of your choice.
Step 5.A
If SuperUser apk or any app that ask for root permission cannot get it, reboot to recovery.
Mount system partition: Shouldn't matter but it worked for me.
Flash SuperSu zip again.
Reboot.
Install SuperUser apk and BusyBox of your choice.
ENJOY

When i connect the device after clicking download, it says "CHIP TYPE NOT match!"
mind you the device is off, i tried to troubleshoot but still getting the same error.
any help would be appreciated
UPDATE: Im thinking it has to be the scatter file, but im not sure.
UPDATE: I got it to work, after flashing superSU, my phone wont boot past the initial white Blu start screen.

[QUOTEUPDATE: I got it to work, after flashing superSU, my phone wont boot past the initial white Blu start screen.[/QUOTE]
Try powering it off, booting to recovery and then wiping dalvik and cache.
The longest it took to get past that logo was 15 minutes. It is either encrypting or decrypting. Didn't get any type of messages until after root, and those were optimizing messages. Only one came through before rooting when I interrupted the boot process and that was about encrypting the phone. Phone was encrypted before root, now it is decrypted. Could have something to do with that. Try wiping the cache and dalvik after flashing. I actually flashed it three times in a row. The third was after mounting storage then flashing the SuperSu zip. Once you see the next logo with the colorful circles and hear the sound it might be another wait. That is where it let me know it was optimizing.
I must note: Please use scatter file to Readback your partitions so you can have a backup BEFORE ANYTHING. I didn't and it led me to take this route.

=smith901;72841007][QUOTEUPDATE: I got it to work, after flashing superSU, my phone wont boot past the initial white Blu start screen.
Click to expand...
Click to collapse
Try powering it off, booting to recovery and then wiping dalvik and cache.
The longest it took to get past that logo was 15 minutes. It is either encrypting or decrypting. Didn't get any type of messages until after root, and those were optimizing messages. Only one came through before rooting when I interrupted the boot process and that was about encrypting the phone. Phone was encrypted before root, now it is decrypted. Could have something to do with that. Try wiping the cache and dalvik after flashing. I actually flashed it three times in a row. The third was after mounting storage then flashing the SuperSu zip. Once you see the next logo with the colorful circles and hear the sound it might be another wait. That is where it let me know it was optimizing.
I must note: Please use scatter file to Readback your partitions so you can have a backup BEFORE ANYTHING. I didn't and it led me to take this route.[/QUOTE]

chip type not match. pls help
---------- Post added at 10:46 AM ---------- Previous post was at 10:41 AM ----------
ANJIII said:
chip type not match. pls help
Click to expand...
Click to collapse
what version of stock rom did you use? there are 3 versions in needrom; v7, v11, and v12. i use v11 cause of automatic update

ANJIII said:
chip type not match. pls help
---------- Post added at 10:46 AM ---------- Previous post was at 10:41 AM ----------
what version of stock rom did you use? there are 3 versions in needrom; v7, v11, and v12. i use v11 cause of automatic update
Click to expand...
Click to collapse
i solved my own problem hahaha. just rename the file to mt6737t instead of mt6735. also edit the platform in scatter file. change it to mt6737t too then install your supersu with the use of twrp then wipe dalvic then its done

ANJIII said:
i solved my own problem hahaha. just rename the file to mt6737t instead of mt6735. also edit the platform in scatter file. change it to mt6737t too then install your supersu with the use of twrp then wipe dalvic then its done
Click to expand...
Click to collapse
Good. I had to name it that because of the chip mismatch error. It was from the V7 ROM. The other two are updates. I also messed up big time along the way. My phone always read MT6735 but it does have MT6737T in different files. I always wondered about that. I got it to work without buying another phone.

It seem that the phone boot logo never goes away. What should I do now?

Alexis96312 said:
It seem that the phone boot logo never goes away. What should I do now?
Click to expand...
Click to collapse
Hope you Readback your original recovery and other partitions. I didn't and worked hard to get it back. When I just flashed the recovery and something went wrong, it reverted back to the stock recovery.
Try doing this:
1. Start SPFT with the reçovery you want to flash.
2. Hold down the power button. AS SOON AS IT VIBRATES, PLUG THE USB CORD IN.
3. Hopefully you timed it right and it will flash and boot.
Sometimes it took 15 minutes to get past the boot logo.

Here what I did so far
1. Format using SP Flash Tool
2. Download /// By Using Scatter-Loading Files (MT6737T_Android_scatter.txt {From Rom}) Which it check all the boxes AUTO ///// It works but I didn't change the recovery.img like TWRP.img
Download it
It works normal.
___________________________________
But I want TRWP.img to be my recovery for root (SuperSU)
I try SP Flash Tool to change the recovery img to TRWP.img /// Using Scatter-Loading Files (MT6737T_Android_scatter.txt {From Rom}) I UNCHECK ALL BUT RECOVERY.IMG
Before this happen I didn't factory reset or Format anything yet.
It work to Recovery.img but THE BLU LOGO IS STILL LONG
I feel like it not working
Help Help Help ME
Please

Alexis96312 said:
Here what I did so far
1. Format using SP Flash Tool
2. Download /// By Using Scatter-Loading Files (MT6737T_Android_scatter.txt {From Rom}) Which it check all the boxes AUTO ///// It works but I didn't change the recovery.img like TWRP.img
Download it
It works normal.
___________________________________
But I want TRWP.img to be my recovery for root (SuperSU)
I try SP Flash Tool to change the recovery img to TRWP.img /// Using Scatter-Loading Files (MT6737T_Android_scatter.txt {From Rom}) I UNCHECK ALL BUT RECOVERY.IMG
Before this happen I didn't factory reset or Format anything yet.
It work to Recovery.img but THE BLU LOGO IS STILL LONG
I feel like it not working
Help Help Help ME
Please
Click to expand...
Click to collapse
Try flashing stock ROM, wipe data in stock recovery, then flashing TWRP, wipe dalvik.
If that don't work, wipe data then flash stock ROM with TWRP recovery, wipe dalvik.
The scatter file from the stock ROM gave me problems. Had to modify mine.
Don't forget to restore your IMEI afterwards since you formatted+flashed.

I will try
---------- Post added at 08:33 PM ---------- Previous post was at 08:23 PM ----------
I did try it but it seem not to do anything
Can you be so kind to upload the mod Scatter File Please

Alexis96312 said:
I will try
---------- Post added at 08:33 PM ---------- Previous post was at 08:23 PM ----------
I did try it but it seem not to do anything
Can you be so kind to upload the mod Scatter File Please
Click to expand...
Click to collapse
The one I attatched on the first post #1 is my modified scatter file. The mods included changing the size to the system, cache, and userdata. Just compared all three. The stock MT6737T scatter file and the V12 ota scatter are the same. The one I changed, MT6735, have the file name, platform name, and partition changes. I don't know why I had to modify it., especially the size parts. It all worked when I did that. I basically gave up on it because of a hard brick. Then I remembered reading MT6735 in some file a few months back while roaming the file system. Made the changes and was back in business. Maybe you need the stock scatter file, here it is.
It's what the end result of this post @ANJIII did minus the size changes..
He just did the name changes and it worked for him. Ya'll seem 180° from where I was.
The second one is from the V12 OTA update. It is very minimal, must be all that is needed for a scatter file. Not really sure tho. Hope it is just scatter file issues.
As long as SPFT is reading your phone, it's still a chance on it all working out. That is how I viewed it.
@andromedaXVIII Don't know if you got it working. This might be a potential solution.

Unable to find partition for path '/sdcard'
Unable to find partition for path '/sdcard'
Unable to find partition for path '/sdcard'
Updating partition details...
Failed to mount '/protect_f'(Invalid argument)
Failed to mount '/protect_s'(Invalid argument)
Failed to mount '/nvdata' (Invalid argument)
...done
Full SELinux support is persent,
MTP Enable
Wiping Dalvik Cache Directories...
--Dalvik Cache Directories Wipe Complete!
Formatting Cache using make_ext4fs..
Updating partition details...
Failed to mount '/protect_f'(Invalid argument)
Failed to mount '/protect_s'(Invalid argument)
Failed to mount '/nvdata' (Invalid argument)
..done
Is this good or bad? This is in Twrp recovery

Alexis96312 said:
Unable to find partition for path '/sdcard'
Is this good or bad? This is in Twrp recovery
Click to expand...
Click to collapse
I take it TWRP flashed successfully, it is having a problem reading those four partitons. Possibly encryption is stopping you. Try flashing this in TWRP before anything else to remove the encryption.
I didn't get any errors. I know the userdata partition was different in the scatter files. That could be the reason for /sdcard not being recognized. Must be a difference in the layout of phones, not really sure. My protect_s, protect_f, and nvdata partitions and /sdcard all mount fine, pictures attached. I am able to do a backup in TWRP. I have been playing around with porting different ROMs and came across an issue similar to this. Had to change some lines in updater-script.
I checked fstab.mt6735 file in the stock recovery, the modded twrp3 recovery, and stock boot recovery to make sure I didn't make any typos or leave anything out. They all have the same lines. Had to do this:
Code:
("ext4", "EMMC", "/dev/block/mmcblk0p5", "/system")
in the updater-script I was working on. I got ahead of myself flashing a ROM and was stuck on the 1st logo screen. Held power+vol_down to get it unstuck. Yes I was all calling myself kind of names like I'm sure some people have done following this guide.
Which scatter file you used? Did you do a readback in SPFT with the WORKING scatter file and mount one of those images to check if you can read and write the files. I mounted system.img from the stock ROM to make sure I could read and write the files before I started with flashing. I'm thinking there is are internal differences in the XL2s. You might have to reflash using the stock ROM with TWRP as the recovery with the Format+Download option since you got TWRP installed.
Once I get through playing around with trying to flash this ROM, I will restore and try to find all the partition mappings and update TWRP to work with the format from the updater-script and see if that work. Will let you know what happened.

Alexis96312 said:
Unable to find partition for path '/sdcard'
Unable to find partition for path '/sdcard'
Unable to find partition for path '/sdcard'
Updating partition details...
Failed to mount '/protect_f'(Invalid argument)
Failed to mount '/protect_s'(Invalid argument)
Failed to mount '/nvdata' (Invalid argument)
...done
Full SELinux support is persent,
MTP Enable
Wiping Dalvik Cache Directories...
--Dalvik Cache Directories Wipe Complete!
Formatting Cache using make_ext4fs..
Updating partition details...
Failed to mount '/protect_f'(Invalid argument)
Failed to mount '/protect_s'(Invalid argument)
Failed to mount '/nvdata' (Invalid argument)
..done
Is this good or bad? This is in Twrp recovery
Click to expand...
Click to collapse
can you send us your vivo xl2 specs because there are two versions of xl2, V0070UU and V0070EE. Mine is V0070UU. I just did some renaming and editing in the scatter file of MT6735 and it bootloop once after I installed the twrp. I restarted my phone during the bootloop by holding the power button. After that, I opened the twrp to install the supersu then wipe dalvic cache. You may now boot up the phone and it took 10-15mins to use it because the system shows that it optimizes 205 apps(in my case, maybe because I have installed numerous apps). After that my phone is usefull again and I installed V4A because that's the only reason why I wanted to root this phone.

Here is all the information I have pulled so far from the phone. Have a screenshot attached from About device in settings. The attached zip file is all the information I could think to pull using adb . The attached file is my partitionlayout. I just ran cat against every file to see what it would give me and redirected the output. Using adb while the phone is in recovery let me pull and read the files I couldn't while the phone was booted.
@Alexis96312, try to run this command in terminal to get your partition map:
Code:
adb shell "su -c 'ls -l /dev/block/platform/mtk-msdc.0/11230000.msdc0/by-name/'" > someFileName.txt
I have mine listed in the zip file as partitionLayout.txt It will list which names go to what device in /dev and save it in your current directory. The file can be used to get the correct partition layout on your phone. Post the results and I will repack the recovery to see if it will work for you. You can do it also with Carliv Image Kitchen, it has a menu :good:. You will have to modify the fstab files in the ramdisk folder of the extracted image to what the partition map specifies. I went thru all of them to be sure when I first ported TWRP.
@ANJIII is correct about the different versions, nice catch. I forgot about that. I assumed you had the V0070UU version like mine, fault on me for not asking. Mine specifically says BLU_V0070UU_V07_GENERIC 25-11-2016 09:46. I'm thinking the GENERIC part comes from me having to flash the stock ROM. I think it had BLU_V0070UU_V07 with user/keys before I bricked it and had to flash the stock ROM. Got three extra apps that I instantly removed. Seems like the stock ROM function the same as before bricking flashing stock.

ScreenShot
ANJIII said:
can you send us your vivo xl2 specs because there are two versions of xl2, V0070UU and V0070EE. Mine is V0070UU. I just did some renaming and editing in the scatter file of MT6735 and it bootloop once after I installed the twrp. I restarted my phone during the bootloop by holding the power button. After that, I opened the twrp to install the supersu then wipe dalvic cache. You may now boot up the phone and it took 10-15mins to use it because the system shows that it optimizes 205 apps(in my case, maybe because I have installed numerous apps). After that my phone is usefull again and I installed V4A because that's the only reason why I wanted to root this phone.
Click to expand...
Click to collapse
Answer in pictures

ADB USB
It seem that the computer can't find it what now
Do I need to install the ADB driver again?
I'm trying to do it on stock recovery
Do I have to do it on TWRP recovery?

Alexis96312 said:
It seem that the computer can't find it what now
Do I need to install the ADB driver again
Click to expand...
Click to collapse
It look like the pid:vid aren't recognized correctly. Usually a reboot will help.
Are you connect using adb while in recovery? If so, see if Windows will install new drivers for you. My Linux box read mine as a Samsung at one point. Try running the ls part of the command in TWRP terminal.
This is where I fought with windows when the cord got pulled during flashing. I never got an error like the 2 at the top, always like the bottom one. I kept adding legacy hardware in device manager until one of them worked. The Linux version of SPFT always give a chip mismatch error. Wish it worked so I won't have to boot to Windows.
I kept doing format+download and and plugging the phone in until Windows recognized it because it was in a bootloop when that happened. You need the preloader to be recognized.
Both stock ROMs are on needrom.com. I downloaded the UU version, the EE version is what you might need. I'll pm you a link to my backups from TWRP to see if they will work for you. Same thing happened to me playing with the new ROM. Restoring my boot and system got it back working.

Question GSI ROM installation unlimited booting

I'm having trouble installing GSI on the Galaxy Tab A8 2021.
1.Dedicated TWRP Recovery in XDA data was released as Odin after bootloader.
2.I entered the TWRP recovery and there was a unable mount twrps error.
3.To solve the problem, I entered the Format Data of the Wipe section of the TWRP Recovery, entered yes, and initialized it. The problem has been solved since then.
4.To install GSI, I went to the Wipe item in TWRP Recovery and tried Swipe to factory Reset, then pressed Advanced Wipe, selected Dalbik/ART Cache,Metadata,Cache,Data,Internal Storage, and tried Swipe to Wipe.
5.Select Fastboot from the Reboot item in TWRP Recovery and enter Fastboot mode.
6.I ran Google Platform-tools_r33.0.3-windows on my computer and typed the command you see in the picture.
7.I ran Fastboot -w after flashing GSI, but I got an error and reboot my Galaxy Tab will boot indefinitely.
*The GSI ROM file used the 9/12 UNOFFICICAL arm64 bgs.img file of Lineage os19.1.
*The firmware version of the Galaxy Tab is the most recent version.
Please check if there is a problem with my installation method.
I'm a person who doesn't know how to use English, so I used a translator. Thank you for your understanding.

In the step #7, instead of run "fastboot -w" try to flash the system file with "fastboot flash system nameofthe.img". After that, reboot in recovery again and format data like you usually do with TWRP, finally try to reboot the system.