Database Develop

Stuck in fastboot

Hello,
This is my first thread here, so when it's not in the right section please let me know.
My huawei ascend p7 is stuck in fastboot&rescue mode.
Before my screen was stuck so i didn't had image on display.
I tried to fix it with the buttons but that didn't work (don't know which combinations i tried exactly)
After putting back my connector, the screen worked.
Now i am stuck in de fastboot mode.
Can someone help me to get out?

Hi, here is what I can told you, but be sur you have no other way, I always take the easiest way, and the way I know to solve a problem, so maybe u can have smthg easier.
Infos:
Power & VOL+ = Recovery
Power & VOL+ & VOL- = Force update (only via stock recovery & dload folder)
Wired to PC, Power & VOL- = Fastboot (the screen you got)
Needed:
Unlocked BL
ROM B121 or B609 (depending on what you had before it ran out, and maybe it can work with any full rom in update.app)
Huawei Update Extractor
Extract the correspondant rom, extract all
Then when your phone is connected you write for each unpacked file:
fastboot flash xx xx.img
Like: fastboot flash boot boot.img
fastboot flash recovery recovery.img
etc... ( will give you the batch i made for this)
After this you have a stable fonctionnal etc rom this installation is wrong. So now:
Install TWRP 2.8.1.0, Install MyRom 1.2 or 3.3 (depending on your initial B1xx or B6xx)
Then:
Create on SDcard a folder called "dload" (without quotes) put the Bxxx that you extracted the files from into "dload"
Reboot in fastboot
Flash the stock recovery
Force update (3 buttons)
Then you should be able to get your phone back

Fully agree with @Kicroy,
but you can do a little easier, just do only the second part.
So, if you were on a B1xx rom flash TWRP 2.8.1.0 and MyRom 1.2; If you were on B6xx flash TWRP 2.8.7.0. and MyRom 3.3.
After that you have to extract the recovery of the rom (B1xx/B6xx) you had been using. Now flash this recovery through adb like he described and go on with dload etc.

Updated, now no sim
I figured out the update and it's beeing updated now till B815 from "huaweiblog".
But now i have a different problem.
My sim is not recognized anymore
Someone can help me?

I'd recommend to flash B800, then downgrade to B621, update afterwards to B623 -> B830. This way you will get to the official lollipop rom.
Did you remove your sim, blowed a little bit in the sim tray and put it back? If that doesn't help try the sim in another phone (eventually do a factory reset)

l3Nni said:
I'd recommend to flash B800, then downgrade to B621, update afterwards to B623 -> B830. This way you will get to the official lollipop rom.
Did you remove your sim, blowed a little bit in the sim tray and put it back? If that doesn't help try the sim in another phone (eventually do a factory reset)
Click to expand...
Click to collapse
Can you give me links where i can find the roms you suggested?
I can't find them.
I removed the sim an blowed in the sim tray, not working.
The sim is oke, it's working in another phone.

B800 http://download-c.huawei.com/download/downloadCenter?downloadId=48763&version=113125&siteCode=it
B621 http://download-c.huawei.com/download/downloadCenter?downloadId=48964&version=113966&siteCode=it
B623 https://drive.google.com/file/d/0B_vgYwoT2KBeQ3lTRTM1NkY3WFk/view?pli=1
B830 https://mega.nz/#!Lp0QFBhT!8tEKtwm8e8WyYd00jeIM0OBgikCIm9ezIPFF1vgmvWU

I did the downgrade to B609.
Sim is not working all the time.
I think my phone is stuck :crying:

Assumable yes, looks like an hardware defect.. So, contact your dealer if you have still warranty.

Thanks for all the reply's.
My phone is out of warranty and stuck
Going to get another one.

Ahh, thats annoying then.
You may think about a reparation by yourself, it's not as complicated as you may think. Even if you let a shop do this it might be worth it..

Maybe your phone lost the IMEI code along the process and that's the cause of the SIM failure.
Dial *#06# on your P7, and if shows all zeros, you have this issue.

EVA-L09 Bootloop and can't turn off

I was trying to downgrade and something went wrong.
Now i'm stuck in Huawei LOGO and can't turn off phone, he keeps turning on and freeze at Huawei Logo.
He's getting really hot.
Tried a few tools to get him at adb but no luck...
Also tried update from dload sdcard but combo keys not working either...
Any ideas?

Delete
Enviado do meu iPhone usando o Tapatalk

migueli2 said:
I was trying to downgrade and something went wrong.
Now i'm stuck in Huawei LOGO and can't turn off phone, he keeps turning on and freeze at Huawei Logo.
He's getting really hot.
Tried a few tools to get him at adb but no luck...
Also tried update from dload sdcard but combo keys not working either...
Any ideas?
Click to expand...
Click to collapse
Same problem but on EVA-AL00 running AL19C636B190
Have u tried to unlock bootloader or flash boot/recovery with fastboot mode?

I have the same problem, any ideas?

I had the same issue, three only thing that worked for me was to get the phone into recovery, vol down and power and flash through DC phoenix

My P9 make "self reset" all time, until battery gets empty. I can't get into recovery

Open hisuite enter recovery area plug phone to pc you see vol down + power screen. Press vol- and power button you must go to fastboot screen. If phone recover by hisuite thats ok.
If not, you need unlocking bootloader with srk tool ( must have unlock code ) flash twrp with command fastboot flash recovery twrp.img or use srk tool to flash twrp recovery.
Enter recovery upload files to sd card, flash L09C432B322 zip than hw_eu zip. Your phone must boot with nougat. (Of course your phone dont C432, you must use your phone B322 files)
If you dont use nougat do a rollback prosedure.

master' said:
Open hisuite enter recovery area plug phone to pc you see vol down + power screen. Press vol- and power button you must go to fastboot screen. If phone recover by hisuite thats ok.
If not, you need unlocking bootloader with srk tool ( must have unlock code ) flash twrp with command fastboot flash recovery twrp.img or use srk tool to flash twrp recovery.
Enter recovery upload files to sd card, flash L09C432B322 zip than hw_eu zip. Your phone must boot with nougat. (Of course your phone dont C432, you must use your phone B322 files)
If you dont use nougat do a rollback prosedure.
Click to expand...
Click to collapse
I have same problem ,but my is Eva 19l,not support hisuite,and I can't turn on the phone check product ID can't unlock bd ...... anything can help me?

Happy baby said:
I have same problem ,but my is Eva 19l,not support hisuite,and I can't turn on the phone check product ID can't unlock bd ...... anything can help me?
Click to expand...
Click to collapse
Use dc phoneix for unlock bootloader . (I dont use so i dont know how to use)

Did anyone ever find an working solution for this, my problem is almost identical to the OP's but mine gets stuck on the bootloader unlocked warning screen, says the phone is rebooting but never does. I'm unable to turn the phone off without it instantly restarting and hanging on the bootloader warning screen, phone also gets super warm when on this screen. HELP

P9 bootloop After flashing Rollback Package (EVA-L19,C900B300)

hi everyone...Please help!
I would like to update to( L19C636B361 EMUI 5.0). But I am stuck at a bootloop as I flashed in the wrong order. I first flashed the update.app (HUAWEI P9 Rollback Package-EVA-L19, from EMUI5.0+Android7.0 rollback to EMUI4.1+Android 6.0, C900B300) instead of updating to update.app(L19C636B361) [ wrong SD card inserted].
Then the phone rebooted and I got into the bootloop at Huawei logo. It cannot be turned off. It can only go into fastboot mode. Bootloader is locked and I cannot unlock it (though I havent unlock code). I tried adb/fastboot
There is always an error:
"FAILED: Remote: Command not allowed"
Now I tried to extract (L19c636b190) system.img , recover.img, boot img, flash it via adb/fastboot, but all failed. When I try to get into fastboot it says locked for both lines, and HiSuite tells me it has no software version for this phone version to repair the phone.
Could anyone help me solve the above situation?
Big [email protected]@

Anyone can help....please.
Coz i bring it to the service center, they charge me a unresonable price.

Try with the Marshmallow version and three buttons

Hey buddy. I had the same situation. Here is what I did: First format your sd card. After then download the right firmware where you can find at the huawei support official web page. After than try dload method. First time it will fail but your phone will open. Do a factory reset. Open your phone and flash firmware with dload method again. This time it will be successful and your phone will be stock. Just try. Sometimes methods fail bcoz of wrong files or sd card mistakes.

hiphoplife77 said:
Hey buddy. I had the same situation. Here is what I did: First format your sd card. After then download the right firmware where you can find at the huawei support official web page. After than try dload method. First time it will fail but your phone will open. Do a factory reset. Open your phone and flash firmware with dload method again. This time it will be successful and your phone will be stock. Just try. Sometimes methods fail bcoz of wrong files or sd card mistakes.
Click to expand...
Click to collapse
hi buddy, thanks for your reply
I follow your instrustions, i download the firmware on huawei web site {huawei_Asia_L19c636b190_16_01_2017(3,246,250kb)} with SD card format (fat32) or (exFat). Itried to dload method, I hold volume+- and power key and plug in to computer(windows 10). The phone will vibrate after 5 seconds. But it stuck into huawei logo,it cannot move forward to EMUI update. Besides, the notification light is red and flashing. Reboot and reboot again.
On the other hand, i tried the fastboot mode. I confirmed my device driver works with window, but i don't have any unlock code in order to flash any 3rd party rom. In my P9 , It showed "phone lock" & FRP Lock".
How did you work with dload method? Please kindly share with me ...thank for your reply again.

I had same issue with L19C432B378 92mb rollback file, first time bootloop. Try 5-6 times with 3 button restart and finally enter dload mode.
Second time 92mb flashing and my phone boot L19C900B300.

If there is red led notification, you are out of battery. Charge it about 15 minute first. So card format must be fat32 and fully formatted, not quick format. After than dload method. One more thing; dont plug your phone when trying dload method. Just hold 3 button about 10 seconds. Just try again. If you have right firmware, you will be successful.

hiphoplife77 said:
If there is red led notification, you are out of battery. Charge it about 15 minute first. So card format must be fat32 and fully formatted, not quick format. After than dload method. One more thing; dont plug your phone when trying dload method. Just hold 3 button about 10 seconds. Just try again. If you have right firmware, you will be successful.
Click to expand...
Click to collapse
Hi,
I have the same problem. After trying update in dload mode stuck in bootloop mode. I tried several times to reenter dload mode, but unsuccessful. Now I am out of battery and didn't want to charge in any mode.
Keep restarting every time I put it to charge. Any idea how to charge the battery?
Thanks

Did you got any solution?? Im having the same problem right now

(Tutorial) Recovering a P10/P10+ Brick

Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
Bootloader already unlocked + Code (no need of twrp)
SD Card
Custom recovery (fix the entire update process)
Stock rom UPDATE.APP from update.zip and update_full_xxx-xxx_hw_xx.zip
for your P10 + P10+ (choose the one you want to install, no need to be the one that come from with your P10, it could be the most recent one but linked to your exact model)
Be patient
Extract the stock rom update.zip and update_full_xxx-xxx_hw_xx.zip, both have an UPDATE.APP,
we are going to flash the one from the update.zip first and repeat the same process for the update_full_xxx-xxx_hw_xx.zip one.
(1)Get ready your SD card
Insert your SD card on the PC, create a folder at the root and name this one dload, move the update.APP from the update.zip
to the dload folder.
(2)Boot your phone in fastboot (Hold Vol- + Power) USB cable need to be plug
Launch terminal on OSX or Windows with adb/fastboot
Write the command fastboot flash recovery customrecovery.img
(3) Before rebooting your phone, insert your sd card that contain dload folder (update.app stock rom from update.zip) inside your P10/P10+
Turn off your P10/P10+
(4) Unplug the USB cable and hold vol+/vol- 5 to 10 sec or (until you see the message this device can not be trusted)
(5)Now the custom recovery updater should trigger and your P10/P10+ is updating, wait until 100% (it restart by itself).
(6)Your P10/P10+ should now boot without problem (bootloader locked)
(7) Is not finish yet, you are going to face NRD90M Test-keys that is normal, you simply need to
flash your cust.
(8) For that, we repeat the same process than before but instead of using the update.app from update.zip, you use the one from update_full_xxx-xxx_hw_xx.zip and replace the one you have on your sd card (dload folder)
(9)reboot your P10/P10+ in fastboot (with of course USB cable plug and hold vol- + power)
There you simply write the command, fastboot oem unlock yourcode. Your phone is going to reset to unlock back your bootloader and you need to go back to fastboot
(10) after that, you reflash again the recovery with customrecovery.img using the command fastboot flash recovery customrecovery.img
and you reboot again in the custom recovery mode (same than before) there the P10/P10+ is updating again, take a few secs
(11) the P10/P10+ will restart and boot in the UI, congrats.:good::good:
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.

neverd said:
Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
Bootloader already unlocked + Code (no need of twrp)
SD Card
Custom recovery (fix the entire update process)
Stock rom UPDATE.APP from update.zip and update_full_xxx-xxx_hw_xx.zip
for your P10 + P10+ (choose the one you want to install, no need to be the one that come from with your P10, it could be the most recent one but linked to your exact model)
Be patient
Extract the stock rom update.zip and update_full_xxx-xxx_hw_xx.zip, both have an UPDATE.APP,
we are going to flash the one from the update.zip first and repeat the same process for the update_full_xxx-xxx_hw_xx.zip one.
(1)Get ready your SD card
Insert your SD card on the PC, create a folder at the root and name this one dload, move the update.APP from the update.zip
to the dload folder.
(2)Boot your phone in fastboot (Hold Vol- + Power) USB cable need to be plug
Launch terminal on OSX or Windows with adb/fastboot
Write the command fastboot flash recovery customrecovery.img
(3) Before rebooting your phone, insert your sd card that contain dload folder (update.app stock rom from update.zip) inside your P10/P10+
Turn off your P10/P10+
(4) Unplug the USB cable and hold vol+/vol- 5 to 10 sec or (until you see the message this device can not be trusted)
(5)Now the custom recovery updater should trigger and your P10/P10+ is updating, wait until 100% (it restart by itself).
(6)Your P10/P10+ should now boot without problem (bootloader locked)
(7) Is not finish yet, you are going to face NRD90M Test-keys that is normal, you simply need to
flash your cust.
(8) For that, we repeat the same process than before but instead of using the update.app from update.zip, you use the one from update_full_xxx-xxx_hw_xx.zip and replace the one you have on your sd card (dload folder)
(9)reboot your P10/P10+ in fastboot (with of course USB cable plug and hold vol- + power)
There you simply write the command, fastboot oem unlock yourcode. Your phone is going to reset to unlock back your bootloader and you need to go back to fastboot
(10) after that, you reflash again the recovery with customrecovery.img using the command fastboot flash recovery customrecovery.img
and you reboot again in the custom recovery mode (same than before) there the P10/P10+ is updating again, take a few secs
(11) the P10/P10+ will restart and boot in the UI, congrats.:good::good:
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.
Click to expand...
Click to collapse
Thanks, will try this tomorrow!

This sound interesting if this method is working both P10 and P10+. It mean that we can rebrand all of L09 models to L29 easily. Am i right? No more FunkyHuawei.
Sent from my iPad using Tapatalk

I have a problem, my P10 boots and lets me configure like it's the first time, but doesn't go anywhere from there, just keeps asking the same stuff... Pls help :/

neverd said:
Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.
Click to expand...
Click to collapse
Perfectly. Quite another matter. :good:

CrazyKat8091 said:
This sound interesting if this method is working both P10 and P10+. It mean that we can rebrand all of L09 models to L29 easily. Am i right? No more FunkyHuawei.
Sent from my iPad using Tapatalk
Click to expand...
Click to collapse
Not sure about the rebranding, for that you need to mod your oem info and product/vendor id.
There is no need of FunkyHuawei, I actually don't support those kind of forcing.

SkexxGo said:
I have a problem, my P10 boots and lets me configure like it's the first time, but doesn't go anywhere from there, just keeps asking the same stuff... Pls help :/
Click to expand...
Click to collapse
Question about the bootloader relock
the command to relock is fastboot oem relock yourcode.
Now about your issue, did you try a wipe cache/wipe factory/reset, go into the stock recovery and do a wipe cache/wipe factory reset.

neverd said:
Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
Bootloader already unlocked + Code (no need of twrp)
SD Card
Custom recovery (fix the entire update process)
Stock rom UPDATE.APP from update.zip and update_full_xxx-xxx_hw_xx.zip
for your P10 + P10+ (choose the one you want to install, no need to be the one that come from with your P10, it could be the most recent one but linked to your exact model)
Be patient
Extract the stock rom update.zip and update_full_xxx-xxx_hw_xx.zip, both have an UPDATE.APP,
we are going to flash the one from the update.zip first and repeat the same process for the update_full_xxx-xxx_hw_xx.zip one.
(1)Get ready your SD card
Insert your SD card on the PC, create a folder at the root and name this one dload, move the update.APP from the update.zip
to the dload folder.
(2)Boot your phone in fastboot (Hold Vol- + Power) USB cable need to be plug
Launch terminal on OSX or Windows with adb/fastboot
Write the command fastboot flash recovery customrecovery.img
(3) Before rebooting your phone, insert your sd card that contain dload folder (update.app stock rom from update.zip) inside your P10/P10+
Turn off your P10/P10+
(4) Unplug the USB cable and hold vol+/vol- 5 to 10 sec or (until you see the message this device can not be trusted)
(5)Now the custom recovery updater should trigger and your P10/P10+ is updating, wait until 100% (it restart by itself).
(6)Your P10/P10+ should now boot without problem (bootloader locked)
(7) Is not finish yet, you are going to face NRD90M Test-keys that is normal, you simply need to
flash your cust.
(8) For that, we repeat the same process than before but instead of using the update.app from update.zip, you use the one from update_full_xxx-xxx_hw_xx.zip and replace the one you have on your sd card (dload folder)
(9)reboot your P10/P10+ in fastboot (with of course USB cable plug and hold vol- + power)
There you simply write the command, fastboot oem unlock yourcode. Your phone is going to reset to unlock back your bootloader and you need to go back to fastboot
(10) after that, you reflash again the recovery with customrecovery.img using the command fastboot flash recovery customrecovery.img
and you reboot again in the custom recovery mode (same than before) there the P10/P10+ is updating again, take a few secs
(11) the P10/P10+ will restart and boot in the UI, congrats.:good::good:
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.
Click to expand...
Click to collapse
Hi neverd, I'm gonna give this method a try. Could you tell me where I can find the appropriate files for my P10 VTR-L29C636B120?
Much thanks.

JustXDAing said:
Hi neverd, I'm gonna give this method a try. Could you tell me where I can find the appropriate files for my P10 VTR-L29C636B120?
Much thanks.
Click to expand...
Click to collapse
Carefully, they use the same name (update.zip) but one is the full ota, the other one the ota mf (cust, etc. the one that you need to flash the second time)
Update.zip VTR-L29C636B120
Update cust/hw xxx

neverd said:
Question about the bootloader relock
the command to relock is fastboot oem relock yourcode.
Now about your issue, did you try a wipe cache/wipe factory/reset, go into the stock recovery and do a wipe cache/wipe factory reset.
Click to expand...
Click to collapse
Thanks about the relock command. I'll try it when I recover my phone.
I tried that, but it's like I don't have the full system installed, I tried a "full" ROM on the first flash, but I don't think it was actually a full rom, it was too small, I wanted to try another one, but the file being over 4gb I can't even copy it to a fat32 sd card... If I find another version that is a little smaller, maybe I could try, but now I only have erecovery, can't access anything else, hope it's enough.

neverd said:
Carefully, they use the same name (update.zip) but one is the full ota, the other one the ota mf (cust, etc. the one that you need to flash the second time)
Update.zip VTR-L29C636B120
Update cust/hw xxx
Click to expand...
Click to collapse
Thanks for the files!
I'm having a problem at step 4, it says software install failed right after 5%.
Just to confirm what I did. Press all 3 buttons (vol up, vol down, power) on until screen shows message.

Guys check this thread https://forum.xda-developers.com/mate-9/how-to/guide-mate-9-flash-update-package-t3593108 it will flash the complete FULL Firmware and you also got your bootloader closed again

JustXDAing said:
Thanks for the files!
I'm having a problem at step 4, it says software install failed right after 5%.
Just to confirm what I did. Press all 3 buttons (vol up, vol down, power) on until screen shows message.
View attachment 4136448
Click to expand...
Click to collapse
I'm having the same problem, can someone send me the files to the VTR-L09 C432? Or maybe the VTR-L29 if my phone supports it, I'd like the dual sim feature.
Just to make sure I'm using the right firmware.
If I find a solution I'll share it here as well btw.

crucky said:
Guys check this thread https://forum.xda-developers.com/mate-9/how-to/guide-mate-9-flash-update-package-t3593108 it will flash the complete FULL Firmware and you also got your bootloader closed again
Click to expand...
Click to collapse
Does it work for P10 Plus (VKY) ? I only see VTR oeminfo/recoveries files in the zip.
Edit : I went ahead and renamed everything in the VTR folder to VKY (except for eominfo files, since I just want to update), and it worked ! Updated from VKY-L29C432B123 to B130

Hi all,
I have the same issue software install failed right after 5%. Did anyone get past this?
What other files other than update in dload folder need to be present?
Thanks
---------- Post added at 05:09 PM ---------- Previous post was at 04:33 PM ----------
SkexxGo said:
I'm having the same problem, can someone send me the files to the VTR-L09 C432? Or maybe the VTR-L29 if my phone supports it, I'd like the dual sim feature.
Just to make sure I'm using the right firmware.
If I find a solution I'll share it here as well btw.
Click to expand...
Click to collapse
Have a look for files :
http://hwmt.ru/hwmtsite/firmware-database/?firmware_model=VTR&firmware_page=0
I think it is the FULL OTA required.
I still cannot get mine to go past 5% stage.

Atf130 said:
Hi all,
I have the same issue software install failed right after 5%. Did anyone get past this?
What other files other than update in dload folder need to be present?
Thanks
---------- Post added at 05:09 PM ---------- Previous post was at 04:33 PM ----------
Have a look for files :
http://hwmt.ru/hwmtsite/firmware-database/?firmware_model=VTR&firmware_page=0
I think it is the FULL OTA required.
I still cannot get mine to go past 5% stage.
Click to expand...
Click to collapse
I've did it with mine, take a look to this post https://forum.xda-developers.com/ma...te-package-t3593108/post72148764#post72148764

CrazyKat8091 said:
This sound interesting if this method is working both P10 and P10+. It mean that we can rebrand all of L09 models to L29 easily. Am i right? No more FunkyHuawei.
Click to expand...
Click to collapse
Really interested in this one too. Do you have any additional information please? As I just have plan to pull the trigger on funkyhuawei method during the next weekend... But of course I would rather use this manual method if possible.

Guys, did you flash the custom recovery before trying to update.
You really need to flash the stock recovery with the custom recovery, this fix the 5% update fail.
You can also flash recovery2 with.

neverd said:
Guys, did you flash the custom recovery before trying to update.
You really need to flash the stock recovery with the custom recovery, this fix the 5% update fail.
You can also flash recovery2 with.
Click to expand...
Click to collapse
Write that you need to extract customrecovery.img from customrecovery.zip. That would be understandable.

Hi,
does this work - i bricked my Huawei P10 with VTR-L29C432B113 firmware like this
Installed TWRP and i flashed magisk.zip -> that worked for a while
But on next phone reboot it says there is no space on the storage 0%
Now i cant do anything - phone is not usable..
Exept booting twrp and fastboot&rescue mode wich shows
PHONE unlocked
FRP Lock
When i try to
fastboot flash boot boot.img it says that stupid message command not allowed..
I tried to put in a SD Card with the folder dload and an update.app on it in and tried to flash it via VOL+ and VOL- but that fails
Does the provided method work or what can i do?
Thanks! chrizz

Softbrick P9 Plus

Hello folks,
so a friend of mine is a complete noob and have this problem with his p9 plus.
The phone keeps rebooting itself in an endless loop, i can't access recovery and only when plugged in to the PC i can access fast-boot.
Phone is locked, FRP Lock.
With getvar command i managed to get this info:
rescue_phoneinfo: VIE-L09C113B170
seems that there is no full zip of this rom anywhere just partial ota (found those with firmware finder) but even with that when i try to flash recovery i get command not allowed.
On the fastboot screen of the phone i have this reboot reason AP_S_PANIC
anyone knows a how to get the phone out of this? (i was thinking that maybe unlocking the bootloader could be of any use, but in the request page it's needed the Product_ID and i don't have it. (can't *#*#1357946#*#*)

I don't know if it does work in a locked bootloader.
I have my P9+ for a week and maybe if you download a firmware compatible with your version and try to 'hard' update the phone, using a SD card with a update file on a dload folder and restarting the phone pressing VolUp + VolDown +Pwr, you can restore your friend's phone.
I'm sorry if I didn't help, I am myself stucked trying to rollback my version to MM and have the NFC and the Bluetooth working again...

myself also got this problem..please anyone..