Related
A couple of days ago my Huawei p7 started to shut itself down and after that it keeps rebooting.
It starts itself up and I get into the choose your language screen and then it shuts down.
When i try to get into the system recovery (using volume & power) I get the following screen:
Android system recovery <3e>
Huawei software installed failed.
Please retry!
Shutdown system now
There is no UPDATE.APP
.............................................
FAIL
And even in system recovery it keeps rebooting.
Im kinda helpless at the moment not knowing what to do.
Did this occur to anyone ? Is there a solution for this problem ?
Thanks in advance.
You should download firmware update file from Huawei Official web site. Extract dload folder from downloaded archive and put it on your SD card. After that you should try to trigger firmware update with factory reset (method which is usually called "force update") by holding all three buttons when the phone is turned off.
But maybe your phone have some hardware problem if it restarts even in recovery mode.
UPDATE:
Does phone restarts itself when it's in fastboot mode (you can get into that mode by holding VOLUME DOWN and POWER button while phone is turned off and connected into USB port of computer just before pressing that button combination) ??
wekii said:
You should download firmware update file from Huawei Official web site. Extract dload folder from downloaded archive and put it on your SD card. After that you should try to trigger firmware update with factory reset (method which is usually called "force update") by holding all three buttons when the phone is turned off.
But maybe your phone have some hardware problem if it restarts even in recovery mode.
UPDATE:
Does phone restarts itself when it's in fastboot mode (you can get into that mode by holding VOLUME DOWN and POWER button while phone is turned off and connected into USB port of computer just before pressing that button combination) ??
Click to expand...
Click to collapse
I've downloaded the update file and proceeded with your steps. I continued to trigger the firmware update with the factory reset.
At first it seemed to work, the phone started updating but after a couple of seconds it started to reboot itself again
I got the phone in fastboot mode and at this moment it does not restart itself !
I went on downloading Hisuite and at this moment it keeps searching for drivers on the network.
The searching for drivers is taking quite some time is this normal ?
Thank you very much for your help so far !
OK, maybe these are good news if you say that your phone doesn't restart when it's in fastboot mode.
I would recommend you to try to reflash your phone's stock recovery and boot images with those extracted from firmware that you are trying to install.
Follow these steps:
Download Huawei Extractor tool from here,
Open update.app with Huawei Extractor and extract next two images: RECOVERY and BOOT (you can do that by selecting those two images while holding CTRL button, then right click > Extract Selected),
When extracted, rename those two images into "recovery.img" and "boot.img",
Copy those two images into "platform-tools" folder of Android SDK,
Run command prompt and go to "platform-tools" folder by using "cd" command,
Start your phone into fastboot mode,
Enter following command into command prompt: "fastboot devices" (without quotes), you should get your phone's serial number listed, if that's right, go to the next step,
Enter: "fastboot oem get-bootinfo", it needs to say that your bootloader is unlocked. If it's not you need to enter the next command "fastboot oem unlock 1234567812345678", where "1234567812345678" should be replaced with unlock code that is unique for your device. Instructions which explain how to obtain unlock code for your device can be found here,
Flash your phone's recovery with "fastboot flash recovery recovery.img",
Flash your phone's boot image with: "fastboot flash boot boot.img",
After successful flashing of both images, turn your phone off by holding POWER button for a several seconds,
Prepare SD card on your PC by formatting SD card and copying "dload" folder of phone's firmware onto SD card,
After you insert SD card into phone, start your phone with "forced install" method by holding all three buttons on your phone.
After that your phone should process firmware install successfully if there is no some hardware issues. Good luck and inform us about your progress.
wekii said:
OK, maybe these are good news if you say that your phone doesn't restart when it's in fastboot mode.
I would recommend you to try to reflash your phone's stock recovery and boot images with those extracted from firmware that you are trying to install.
Follow these steps:
Download Huawei Extractor tool from here,
Open update.app with Huawei Extractor and extract next two images: RECOVERY and BOOT (you can do that by selecting those two images while holding CTRL button, then right click > Extract Selected),
When extracted, rename those two images into "recovery.img" and "boot.img",
Copy those two images into "platform-tools" folder of Android SDK,
Run command prompt and go to "platform-tools" folder by using "cd" command,
Start your phone into fastboot mode,
Enter following command into command prompt: "fastboot devices" (without quotes), you should get your phone's serial number listed, if that's right, go to the next step,
Enter: "fastboot oem get-bootinfo", it needs to say that your bootloader is unlocked, if it's not read this,
Flash your phone's recovery with "fastboot flash recovery recovery.img",
Flash your phone's boot image with: "fastboot flash boot boot.img",
After successful flashing of both images, turn your phone off by holding POWER button for a several seconds,
Prepare SD card on your PC by formatting SD card and copying "dload" folder of phone's firmware onto SD card,
After you insert SD card into phone, start your phone with "forced install" method by holding all three buttons on your phone.
After that your phone should process firmware install successfully if there is no some hardware issues. Good luck and inform us about your progress.
Click to expand...
Click to collapse
Hi,
I've got the same issue.
When I start to "force install" method, my phone doesn't boot.
It just stay in a state of "charging" but nothing append.
I flashed boot and recovery with Fastboot.
But now, when I start the phone in Fastboot&Rescue Mode, the device doesn't appear in the liste when I run adb devices.
But when I start in the "force install" mode, adb devices returns the serial of the phone (but it doesn't respond to fastboot command).
Are there other files to flash on the phone than juste recovery and boot ?
Thank's for those steps, i'll continue to try to flash again.
Edit :
Ok phone is back !
The problem came from my SD Card, I had not only the dload folder, but an other file.
Format SD Card -> dload folder -> "force install" method -> ENJOY !
Thank's a lot !
wekii said:
OK, maybe these are good news if you say that your phone doesn't restart when it's in fastboot mode.
I would recommend you to try to reflash your phone's stock recovery and boot images with those extracted from firmware that you are trying to install.
Follow these steps:
Download Huawei Extractor tool from here,
Open update.app with Huawei Extractor and extract next two images: RECOVERY and BOOT (you can do that by selecting those two images while holding CTRL button, then right click > Extract Selected),
When extracted, rename those two images into "recovery.img" and "boot.img",
Copy those two images into "platform-tools" folder of Android SDK,
Run command prompt and go to "platform-tools" folder by using "cd" command,
Start your phone into fastboot mode,
Enter following command into command prompt: "fastboot devices" (without quotes), you should get your phone's serial number listed, if that's right, go to the next step,
Enter: "fastboot oem get-bootinfo", it needs to say that your bootloader is unlocked, if it's not read this,
Flash your phone's recovery with "fastboot flash recovery recovery.img",
Flash your phone's boot image with: "fastboot flash boot boot.img",
After successful flashing of both images, turn your phone off by holding POWER button for a several seconds,
Prepare SD card on your PC by formatting SD card and copying "dload" folder of phone's firmware onto SD card,
After you insert SD card into phone, start your phone with "forced install" method by holding all three buttons on your phone.
After that your phone should process firmware install successfully if there is no some hardware issues. Good luck and inform us about your progress.
Click to expand...
Click to collapse
I followed all your steps but i get stuck at step 7. When I give the command fastboot devices it doesn't show my phone's serial number. Instead it shows a ? (question mark).
Did I do something wrong or is there a solution for this?
Thanks in advance!
Maybe you should try other version of platform tools. I would recommend you to download adt-bundle-windows-x86_64-20140702.zip (x64) or adt-bundle-windows-x86-20140702.zip (x32) from "Android SDK" official web pages (I assume that your are using Windows OS). After download extract only "platform-tools" directory to the root of Windows C:\ partition and try described procedure again.
However if you are still getting question marks instead of phone's serial number, you should ignore that step and go onto the next one. I had the same problem in the past and flash commands were successful even serial number wasn't been displayed.
Keep us informed about your progress. Good luck zbnd !!
wekii said:
Maybe you should try other version of platform tools. I would recommend you to download adt-bundle-windows-x86_64-20140702.zip (x64) or adt-bundle-windows-x86-20140702.zip (x32) from "Android SDK" official web pages (I assume that your are using Windows OS). After download extract only "platform-tools" directory to the root of Windows C:\ partition and try described procedure again.
However if you are still getting question marks instead of phone's serial number, you should ignore that step and go onto the next one. I had the same problem in the past and flash commands were successful even serial number wasn't been displayed.
Keep us informed about your progress. Good luck zbnd !!
Click to expand...
Click to collapse
Thanks for your response !
So I followed through like you said. Gave the fastboot oem get-bootinfo command and then I got (bootloader) locked. So I followed the bootloader's unlock code (official way), entered my product SN and product IMEI, used the Huawei Product ID generator followed the procedure and all I get is : Please input the correct Product ID
What did I do wrong this time ? I'm not sure if it's even possible to do this wrong. Is there another way around ?
You can unlock with Vroot, like I did. I didn't try to get a serial from Huawei.
For the Fastboot command 'Fastboot device's I had a ? too, but with 'adb devices' command, I got my serial number.
Sent from my HUAWEI P7-L10 using XDA Free mobile app
Pboguet said:
You can unlock with Vroot, like I did. I didn't try to get a serial from Huawei.
For the Fastboot command 'Fastboot device's I had a ? too, but with 'adb devices' command, I got my serial number.
Sent from my HUAWEI P7-L10 using XDA Free mobile app
Click to expand...
Click to collapse
I've downloaded Vroot (english version) but when i connect my phone it says not support mode
I tried to connect while in fastboot&rescue mode, because this is the only way the phone stays on without restarting.
I then tried to connect without fastboot&rescue mode. But my phone keeps rebooting. I did get a message that USB debugging is disabled. However I can't enable usb debugging because my phone won't boot up normally.
@Pboguet
You should read carefully because your answer has no sense for the phone which is in state like zbnd's phone is.
@zbnd
Maybe you are doing something wrong. You can send me your's phone serial number and IMEI in PM inbox, I will try to generate unlock code for you.
wekii said:
@Pboguet
You should read carefully because your answer has no sense for the phone which is in state like zbnd's phone is.
@zbnd
Maybe you are doing something wrong. You can send me your's phone serial number and IMEI in PM inbox, I will try to generate unlock code for you.
Click to expand...
Click to collapse
Thank you very much for all your help!
Despite following all your steps my phone keeps rebooting
Sorry to hear that. Did you manage to make all steps that I described to you? Can you share more informations about your current efforts please.
wekii said:
Sorry to hear that. Did you manage to make all steps that I described to you? Can you share more informations about your current efforts please.
Click to expand...
Click to collapse
Ik
After unlocking my phone I got the message unlocked in CMD.
I then flashed recovery and boot. Both times it said that the flash was succesfull, this only took a few seconds I don't know if thats normal? I then followed your last steps ( dload folder etc) and put the SD card in my phone.
It start installing but after approximetaly 25 seconds the phone shuts itself down and then reboots.
The procedure then starts again and it starts installing followed by shutting down and rebooting.
I'm sorry to hear that. Seems like it's some hardware issue.
However I still have one more idea that you can try in fastboot mode. I would recommend you to install entire firmware manually with fastboot commands.
By following previously described procedure try to extract with "Huawei Extractor" tool next images also: SYSTEM, USERDATA, CUST and CACHE.
After step number 10, try to use next commands also:
"fastboot flash system system.img"
"fastboot flash cust cust.img"
"fastboot flash userdata userdata.img"
"fastboot flash cache cache.img"
When you are finished with flashing of all images, use "fastboot reboot" command to restart your phone. Steps 11, 12 and 13 should be ignored this time.
Let me know the result
Hey, I'm glad I found this forum, because I have exactly the same problem! Since zbnd did not reply I wanted to let you know that flashing boot.img, recovery.img, cache.img, userdata.img, cust.img and system.img via fastboot did not work
The commandline for each file said "OKAY" and "finished" therefore I assume the process(es) completed succesfully.
Maybe I should tell you some information and the steps I did with my P7:
- my device is a branded german telekom version with firmware P7-L10-V100R001C150B122- because of crappy pink telekom bootlogo und bloatware I wanted to flash the original huawei firmware so I downloaded the B126 from the official website and updated via force update method- at the end of the update process i got the messages "huawei cust fail" and "update_post_process fail" but when I rebootet the B126 was installed and showed a message "Defect report reminders - This is an internal test version. Please report defects to Yangyexiao 00143718" - can't be correct, I thought- after googling a lot and reading through several forums I rooted my device with RootGenius, installed HiSuite and Android-SDK (driver were installed correctly, adb devices showed a device with serial) and deleted the "cust" directory on my phone - at that point everything still worked- next step: I installed TWRP 2.7.1.0, made an updateable zip file with huawei update extractor (including system.img, userdata.img, cust.img and boot.img) and flashed it via TWRP. The process completed succesfully, but needed only a few seconds. After that I got this bootloop at the language selection- then I wanted to return to the last functioning state, so I flashed the stock recovery via fastboot and started with force update method. But after a few seconds the device rebooted during the update process which led to another (maybe the same) bootloop. I had to remove the sd card, but the device continued to reboot in recovery mode. So i installed TWRP 2.7.1.0 again- Then I tried to restore a B133 backup I got from another forum, but it obviously did not work (see attached image)
Now I just don't know what to do ... I get a bootloop in stock recovery and I get a bootloop in TWRP 2.8.0.0.
Only TWRP 2.7.1.0 does not reboot. What is about the other files inside the UPDATE.APP (modemimage.img, efi.img, etc)? Is it possible that some of these files are needed?
Thanks in advance...
mbert said:
Hey,
Only TWRP 2.7.1.0 does not reboot.
Thanks in advance...
Click to expand...
Click to collapse
If this recovery works than try:
1. Save this Se7en or this HRT or this custom MIUI ROM on SD card
2 .Wipe in TWRP everything (dalvik, system,data,cust, internal) except external (SD card). Internal only if You have a backup or not important data there.
4. Install zipp ROM from external memory. Sometimes try more than one time in fail case. For HRT ROM especially.
Let me know if helped.
Ziółek said:
If this recovery works than try:
1. Save this Se7en or this HRT or this custom MIUI ROM on SD card
2 .Wipe in TWRP everything (dalvik, system,data,cust, internal) except external (SD card). Internal only if You have a backup or not important data there.
4. Install zipp ROM from external memory. Sometimes try more than one time in fail case. For HRT ROM especially.
Let me know if helped.
Click to expand...
Click to collapse
failed
I tried se7en and miui.
I wiped dalvik,system,data,internal,cache and custom, which only lasted about 2 seconds, but said succesful (Is that enough to delete all partitions?).
Installation of both custom roms completed succesfully and lastet several seconds (max 1 min I think).
Se7en: reboot -> huawei logo -> reboot -> language selection (in the style of stock rom?) -> reboot ...
Miui: reboot -> miui logo -> reboot -> language selection (miui style) -> reboot -> wifi selection (I skipped) -> searching for sim card -> reboot
mbert said:
Hey, I'm glad I found this forum, because I have exactly the same problem! Since zbnd did not reply I wanted to let you know that flashing boot.img, recovery.img, cache.img, userdata.img, cust.img and system.img via fastboot did not work
The commandline for each file said "OKAY" and "finished" therefore I assume the process(es) completed succesfully.
Maybe I should tell you some information and the steps I did with my P7:
- my device is a branded german telekom version with firmware P7-L10-V100R001C150B122- because of crappy pink telekom bootlogo und bloatware I wanted to flash the original huawei firmware so I downloaded the B126 from the official website and updated via force update method- at the end of the update process i got the messages "huawei cust fail" and "update_post_process fail" but when I rebootet the B126 was installed and showed a message "Defect report reminders - This is an internal test version. Please report defects to Yangyexiao 00143718" - can't be correct, I thought- after googling a lot and reading through several forums I rooted my device with RootGenius, installed HiSuite and Android-SDK (driver were installed correctly, adb devices showed a device with serial) and deleted the "cust" directory on my phone - at that point everything still worked- next step: I installed TWRP 2.7.1.0, made an updateable zip file with huawei update extractor (including system.img, userdata.img, cust.img and boot.img) and flashed it via TWRP. The process completed succesfully, but needed only a few seconds. After that I got this bootloop at the language selection- then I wanted to return to the last functioning state, so I flashed the stock recovery via fastboot and started with force update method. But after a few seconds the device rebooted during the update process which led to another (maybe the same) bootloop. I had to remove the sd card, but the device continued to reboot in recovery mode. So i installed TWRP 2.7.1.0 again- Then I tried to restore a B133 backup I got from another forum, but it obviously did not work (see attached image)
Now I just don't know what to do ... I get a bootloop in stock recovery and I get a bootloop in TWRP 2.8.0.0.
Only TWRP 2.7.1.0 does not reboot. What is about the other files inside the UPDATE.APP (modemimage.img, efi.img, etc)? Is it possible that some of these files are needed?
Thanks in advance...
Click to expand...
Click to collapse
To use fastboot you need to unlock bootloader first. And before flash, you need to erase partition first, for a proper job. Please read well about the fastboot procedure is a dangerous procedure
My bootloader is unlocked, but fastboot sais I don't have permission to erase partitions ...
Gesendet von meinem HUAWEI P6-U06 mit Tapatalk
Hi guys! Yesterday i installed NostromoPop 2.3.0 (08/02/16)[CM12.1][5.1.1] cuz my rear camera wasn't working and i found that could be a fix, but doesn't work. So this morning i tried to put back the stock rom but my phone got stucked on battery logo. I've tried to push power button for a long time and volume down+power . But seems that is not responding.
Could i fix it or it's dead? Thanks! ( Sorry for my bad english)
How are you reinstalling Stock ROM ?
You can try to press Power+Vol Up key to enter recovery, if you have TWRP installed you can re-flash stock ROM from a Nandroid Backup
TryllZ said:
How are you reinstalling Stock ROM ?
You can try to press Power+Vol Up key to enter recovery, if you have TWRP installed you can re-flash stock ROM from a Nandroid Backup
Click to expand...
Click to collapse
I deleted my OS and i can't put the rom on phone. i've tried with adb sideload but my device is unauthorized. now i'm trying with rebootRUU but i've got some error. May you help me?
Arichoo said:
I deleted my OS and i can't put the rom on phone. i've tried with adb sideload but my device is unauthorized. now i'm trying with rebootRUU but i've got some error. May you help me?
Click to expand...
Click to collapse
Is your device locked ?
Rooted ?
have TWRP installed ?
TryllZ said:
Is your device locked ?
Rooted ?
have TWRP installed ?
Click to expand...
Click to collapse
bootloader unlocked
s-on
twrp instaled
and also i instaled supersu but now, when i exit twrp appers to install again
Download this : https://www.androidfilehost.com/?fid=24052804347818782
And do the following :
STEPS TO RESTORE NANDROID BACKUP THROUGH TWRP:
- REBOOT AND ENTER TWRP, PERFORM A BACKUP (THIS WILL CREATE A TWRP BACK UP FOLDER WITH DEVICE SERIAL NUMBER IN THE SD CARD)
- DOWNLOAD AND EXTRACT THE NANDROID BACK UP FILE
- PLACE THE EXTRACTED FILES IN TO THE TWRP>BACKUP<DEVICE SERIAL NUMBER> FOLDER IN THE SD CARD
- RESTART THE DEVICE AND ENTER TWRP, CHOOSE RESTORE
- LOCATE THE FOLDER COPIED IN THE ROOT OF THE SDCARD
- SWIPE TO RESTORE
- FOR SOME REASON THE NANDROID BACKUP DOES NOT CONTAIN CALCULATOR, FLASH LIGHT WHICH CAN BE DOWNLOADED HERE: http://www.apkmirror.com/apk/htc-corporation/
Good Luck...
TryllZ said:
Download this : https://www.androidfilehost.com/?fid=24052804347818782
And do the following :
STEPS TO RESTORE NANDROID BACKUP THROUGH TWRP:
- REBOOT AND ENTER TWRP, PERFORM A BACKUP (THIS WILL CREATE A TWRP BACK UP FOLDER WITH DEVICE SERIAL NUMBER IN THE SD CARD)
- DOWNLOAD AND EXTRACT THE NANDROID BACK UP FILE
- PLACE THE EXTRACTED FILES IN TO THE TWRP>BACKUP<DEVICE SERIAL NUMBER> FOLDER IN THE SD CARD
- RESTART THE DEVICE AND ENTER TWRP, CHOOSE RESTORE
- LOCATE THE FOLDER COPIED IN THE ROOT OF THE SDCARD
- SWIPE TO RESTORE
- FOR SOME REASON THE NANDROID BACKUP DOES NOT CONTAIN CALCULATOR, FLASH LIGHT WHICH CAN BE DOWNLOADED HERE: http://www.apkmirror.com/apk/htc-corporation/
Good Luck...
Click to expand...
Click to collapse
i can't place the files. cuz my phone is stucked in bootloader and recovery.
Arichoo said:
i can't place the files. cuz my phone is stucked in bootloader and recovery.
Click to expand...
Click to collapse
What do you mean bootloader and recovery, TWRP is your recovery...Can you enter TWRP... ?, if you can, enter an SD Card in the phone and make backup...then follow the given steps...
TryllZ said:
What do you mean bootloader and recovery, TWRP is your recovery...Can you enter TWRP... ?, if you can, enter an SD Card in the phone and make backup...then follow the given steps...
Click to expand...
Click to collapse
I wanna say dat i can't put files on my phone. i created the backup but how can i put nandroid files in that folder?
Arichoo said:
I wanna say dat i can't put files on my phone. i created the backup but how can i put nandroid files in that folder?
Click to expand...
Click to collapse
I made it. Thanks a lot man!
"Cyanogendmod.Org / Install CM for z3c / Unlock Your Xperia Z3 Compact" <--- That's the URL somehow.
Followed this instruction. Got myself the 12.1 .zip and .img.
I get error installaing the .zip and the .img isn't even an option:
The old rom is infinitly loading in that blue/purple wave line.
I then turn the phone off by holding down the power button until the phone restarts.
My history:
>Pressing up and down on the button rockers.
>Cyanogen Recovery starts.
>I choose "Wipe data/factory reset".
>I choose "Apply update".
(Apply from ADB doesn't work as it seems as ADB has no access for USB debugging. That's why install it from an external SD)
>Install "cm-12.1-20160918-NIGHTLY-z3c.zip" or its copy that I named "update.zip".
Error message:
[CAN'T POST PICTURE BECAUSE XDA HAS VERY FUNNY MEME RULES XDDD]
Private message maybe...? Can I send you guys URL pics via PM?
How can I get out of this loop?
If you want to go back to stock, use flashtool and flash whatever version you want (FTF method), I had an issue with flashing CM too, it said this is for aries but this device is z3c etc. Is this your problem?
marshalpear said:
If you want to go back to stock, use flashtool and flash whatever version you want (FTF method), I had an issue with flashing CM too, it said this is for aries but this device is z3c etc. Is this your problem?
Click to expand...
Click to collapse
I definitly want CyanogenMod 12.1 on my Z3C. Is it still possible?
I hope you can decypher the URL h t t p : / / t i n y u r l . c o m / j 6 4 u 8 u a
Few things you can do:
1- Download the ROM again, might be corrupted download.
2- Flash Lollipop FTF(not necessary), Flash TWRP recovery, boot into recovery, (If it asks, swipe to allow modifications to system), wipe everything (system,cache,dalvik,data), flash the ROM through TWRP recovery.
3- If it gives the error that I talked about in my first message, let me know.
marshalpear said:
Few things you can do:
1- Download the ROM again, might be corrupted download.
2- Flash Lollipop FTF(not necessary), Flash TWRP recovery, boot into recovery, (If it asks, swipe to allow modifications to system), wipe everything (system,cache,dalvik,data), flash the ROM through TWRP recovery.
3- If it gives the error that I talked about in my first message, let me know.
Click to expand...
Click to collapse
I tried #1 but I'm already stuck with the "SONY XPERIA" blackscreen at the very beginning when booting the smartphone. I suppose it's because of the failed installation and the not choosing of "Wipe clean/factory reset".
I hope that still doesn't count as bricking. I let the accumulator run dry and reload the battery and try to get into the Cyanogenmod Recovery again. Right now nothing is possible. =/
I hope that doesn't count as bricking. If so: These special OTG USB thingies fix a lot I heard, should I get myself one?
SYLVER SECOND said:
I tried #1 but I'm already stuck with the "SONY XPERIA" blackscreen at the very beginning when booting the smartphone. I suppose it's because of the failed installation and the not choosing of "Wipe clean/factory reset".
I hope that still doesn't count as bricking. I let the accumulator run dry and reload the battery and try to get into the Cyanogenmod Recovery again. Right now nothing is possible. =/
I hope that doesn't count as bricking. If so: These special OTG USB thingies fix a lot I heard, should I get myself one?
Click to expand...
Click to collapse
If you are on CM recovery, then there is the problem. AFAIK you can't flash anything through that, so you have to push TWRP on your device using fastboot and then flash AOSP/CM rom you want.
SYLVER SECOND said:
I tried #1 but I'm already stuck with the "SONY XPERIA" blackscreen at the very beginning when booting the smartphone. I suppose it's because of the failed installation and the not choosing of "Wipe clean/factory reset".
I hope that still doesn't count as bricking. I let the accumulator run dry and reload the battery and try to get into the Cyanogenmod Recovery again. Right now nothing is possible. =/
I hope that doesn't count as bricking. If so: These special OTG USB thingies fix a lot I heard, should I get myself one?
Click to expand...
Click to collapse
That's called a soft-brick. You should install the ADB drivers for your phone on your PC and then download TWRP for your phone (.img file) and rename the TWRP you downloaded to recovery.img .
You should put the recovery.img into the folder where your ADB drivers are installed, then Shift + RClick on that folder then select Open Command Window Here. Connect your phone in fastboot mode to your PC (Keep Vol. Up button then plug in your device). Type the following commands:
fastboot flash boot recovery.img
fastboot reboot
If you've done it all correctly, your phone should boot into TWRP recovery. From there you should go to wipe-advanced wipe and wipe your Cache,Dalvik Cache, System, Boot. DO NOT REBOOT NOW. You should go back to main menu and choose install, then choose the ROM you want to install. It should flash it if you don't have a corrupted file. After flashing, you can safely reboot your phone, don't forget to flash GApps if you want Google features on your Cyanogen, hope I helped!
More info about my error:
h t t p : / / t i n y u r l . c o m / z b e v y u 2
Each version of step #3 doesn't work. Still trying to figure out how to get TWRP...
marshalpear said:
That's called a soft-brick. You should install the ADB drivers for your phone on your PC and then download TWRP for your phone (.img file) and rename the TWRP you downloaded to recovery.img .
You should put the recovery.img into the folder where your ADB drivers are installed, then Shift + RClick on that folder then select Open Command Window Here. Connect your phone in fastboot mode to your PC (Keep Vol. Up button then plug in your device). Type the following commands:
fastboot flash boot recovery.img
fastboot reboot
If you've done it all correctly, your phone should boot into TWRP recovery. From there you should go to wipe-advanced wipe and wipe your Cache,Dalvik Cache, System, Boot. DO NOT REBOOT NOW. You should go back to main menu and choose install, then choose the ROM you want to install. It should flash it if you don't have a corrupted file. After flashing, you can safely reboot your phone, don't forget to flash GApps if you want Google features on your Cyanogen, hope I helped!
Click to expand...
Click to collapse
K, 90% of this works. I got the TWRP "app" and I cleaned the cache and all that, but I had to reboot. You see:
To transfer new media I need to remove my external SD from the z3c to my old LG. The LG is connected with my PC and is therefore a kind of card-reader. I tried 2 different nightly thingies.
I still get extraction errors, see:
h t t p : / / t i n y u r l . c o m / h j j d 4 o b
I downloaded 2 different nightlies 6 times already. I dunno. Somethings off here.
Also: For what is the recovery.img? Should I install it afterwards?
I have to restart the phone in order to replug the SD card and get recognigzed by the TWRP.
I did everything from this:
http://forum.xda-developers.com/showthread.php?t=2522762
Because of Error 7.
Now I get Error 6.....
SYLVER SECOND said:
K, 90% of this works. I got the TWRP "app" and I cleaned the cache and all that, but I had to reboot. You see:
To transfer new media I need to remove my external SD from the z3c to my old LG. The LG is connected with my PC and is therefore a kind of card-reader. I tried 2 different nightly thingies.
I still get extraction errors, see:
h t t p : / / t i n y u r l . c o m / h j j d 4 o b
I downloaded 2 different nightlies 6 times already. I dunno. Somethings off here.
Also: For what is the recovery.img? Should I install it afterwards?
I have to restart the phone in order to replug the SD card and get recognigzed by the TWRP.
I did everything from this:
http://forum.xda-developers.com/showthread.php?t=2522762
Because of Error 7.
Now I get Error 6.....
Click to expand...
Click to collapse
OK, your problem is that you messed up your system, so wiping it is not gonna solve this issue. You need to download a stock firmware file (an FTF file) and flash it through Flashtool, because your device name seems to be "." which is why you were getting "error 7". As for the recovery.img, you will use it to flash TWRP recovery on your phone. TWRP app doesn't work correctly if you don't flash it to your recovery partition so do as follows:
1- Download Flashtool, install the drivers of your device for Flashtool (you can search it on xda forums), download an FTF file, any of them should do, but as you will install CM 12.1, I recommend a Lollipop FTF.
2- Flash the firmware through Flashtool. This will turn your phone into a stock one. Unlock your bootloader if you haven't already, which I believe you have.
3- Flash the TWRP recovery through fastboot (follow my earlier instructions)
4- After you open TWRP recovery do the wipes, note that you can still connect your phone to your computer for file transfers in TWRP Recovery.
5- Install the CM zip file through recovery
IF YOU GET ERROR 7 SAYING :this package is for device: D5803, D5833, z3c; this device is aries.
7- Open the CM 12.1 zip file on your computer and proceed to META-INF/com/google/android directory.
8- In that folder you should see "updater-script", extract it to somewhere and open it with Notepad.
9- Once you open it press Ctrl + H to change some of the lines.
10- Write "D5833" without the quotation marks in the first space and write "aries" without the quotation marks into the second space and click replace all.
(This will change all "D5833" to "aries" in the file therefore making it usable for your device) Save the file and put it into the directory of where you found it, replace it with the original.
11- Now put the edited .zip file into your phone storage, and flash it through recovery. It should work. :good:
marshalpear said:
3- Flash the TWRP recovery through fastboot (follow my earlier instructions)
Click to expand...
Click to collapse
I think he shouldn't flash TWRP on boot partition, as you wrote. That might cause further issues. I am flashing my recovery through fastboot without problems using next command:
fastboot flash recovery recovery.img
Cirra92 said:
I think he shouldn't flash TWRP on boot partition, as you wrote. That might cause further issues. I am flashing my recovery through fastboot without problems using next command:
fastboot flash recovery recovery.img
Click to expand...
Click to collapse
It won't matter. Because when he flashes the CM, it'll flash the CM Recovery along with it.
marshalpear said:
It won't matter. Because when he flashes the CM, it'll flash the CM Recovery along with it.
Click to expand...
Click to collapse
Yea I know, but before that, he needs to have a working TWRP on right partition to be able to even flash any rom.
Cirra92 said:
Yea I know, but before that, he needs to have a working TWRP on right partition to be able to even flash any rom.
Click to expand...
Click to collapse
That's why I wrote those steps for him/her to follow. If you flash TWRP to boot partition, when you boot the phone, it will go straight into TWRP. If you flash it to recovery partition, you'll have to boot it manually.
marshalpear said:
That's why I wrote those steps for him/her to follow. If you flash TWRP to boot partition, when you boot the phone, it will go straight into TWRP. If you flash it to recovery partition, you'll have to boot it manually.
Click to expand...
Click to collapse
Logical step, didn't think about it that way, I assumed OP knew how to enter recovery
"1- Download Flashtool, install the drivers of your device for Flashtool (you can search it on xda forums), download an FTF file, any of them should do, but as you will install CM 12.1, I recommend a Lollipop FTF.
2- Flash the firmware through Flashtool. This will turn your phone into a stock one. Unlock your bootloader if you haven't already, which I believe you have.
3- Flash the TWRP recovery through fastboot (follow my earlier instructions)
4- After you open TWRP recovery do the wipes, note that you can still connect your phone to your computer for file transfers in TWRP Recovery.
5- Install the CM zip file through recovery
IF YOU GET ERROR 7 SAYING :this package is for device: D5803, D5833, z3c; this device is aries.
7- Open the CM 12.1 zip file on your computer and proceed to META-INF/com/google/android directory.
8- In that folder you should see "updater-script", extract it to somewhere and open it with Notepad.
9- Once you open it press Ctrl + H to change some of the lines.
10- Write "D5833" without the quotation marks in the first space and write "aries" without the quotation marks into the second space and click replace all.
(This will change all "D5833" to "aries" in the file therefore making it usable for your device) Save the file and put it into the directory of where you found it, replace it with the original.
11- Now put the edited .zip file into your phone storage, and flash it through recovery. It should work."
K, so I guess I'm finished with #1 and #2. Sorry, had a ****-ton of chores to do. Before I progress, I wanted to send you guys
this pic:
https://img3.picload.org/image/rdricord/unbenannt.png
Is the root access necessary, or can I progress?
That's the sites I've used, if anybody wonders why something is the way it is right now:
http://forum.xda-developers.com/z3-compact/general/list-stock-firmwares-d5803-d5833-t2906706
http://forum.xda-developers.com/showpost.php?p=66275965&postcount=2029
http://forum.xda-developers.com/showpost.php?p=60001557&postcount=829
Von "Sony Mobile Flasher by Androxyde":
"23/023/2016 22:23:52 - INFO - Root access denied
23/024/2016 22:24:07 - ERROR - Illegal key size or default parameters
23/024/2016 22:24:12 - ERROR - Illegal key size or default parameters
23/024/2016 22:24:13 - WARN - Please check your Phone and 'ALLOW' Superuseraccess!
23/024/2016 22:24:14 - INFO - Root access denied"
FlashTool says the firmware has been flashed so I don't understand what are you trying to do after that? After flashing the FTF file you should flash TWRP through "FASTBOOT". Then follow the instructions.
K, did everything you said. Read everything five-times. Replaced "D5833" to "aries" and all that stuff. Still getting ERROR 7.
The phone is still in TWRP Recovery from FASTBOOT / BOOTLOAD because I "constantly" charge it to stay in recovery. If I had found this Mount option earlier... kinda feel stupid for that. So I still get ERROR 7. I copied the modified .zip to internal storage and SD card to see if I get the same error twice. And yeah.
Exact error message in red letters:
"Updater process ended with ERROR: 7
Error installing zip file ' /external-sd/cm-12.1-20160918-NIGHTLY-z3c.zip'
Updating partition details...
... done"
So I forethought and cleaned the cache and need somewhat new instructions.
Also:
I suppose with "Advanced Wipe" and your instructions you meant this points, right?:
http://tinyurl.com/jc5rv3a
SYLVER SECOND said:
K, did everything you said. Read everything five-times. Replaced "D5833" to "aries" and all that stuff. Still getting ERROR 7.
The phone is still in TWRP Recovery from FASTBOOT / BOOTLOAD because I "constantly" charge it to stay in recovery. If I had found this Mount option earlier... kinda feel stupid for that. So I still get ERROR 7. I copied the modified .zip to internal storage and SD card to see if I get the same error twice. And yeah.
Exact error message in red letters:
"Updater process ended with ERROR: 7
Error installing zip file ' /external-sd/cm-12.1-20160918-NIGHTLY-z3c.zip'
Updating partition details...
... done"
So I forethought and cleaned the cache and need somewhat new instructions.
Also:
I suppose with "Advanced Wipe" and your instructions you meant this points, right?:
http://tinyurl.com/jc5rv3a
Click to expand...
Click to collapse
OK, so try flashing TWRP to recovery partition to get you out of TWRP after you boot by writing these commands in the ADB:,
fastboot flash recovery recovery.img
fastboot reboot recovery
This will flash the TWRP to recovery partition and will boot you into TWRP. As you do this you won't have a go at the recovery again but for this time. You can reach the TWRP by pressing the Vol. Down button when the phone vibrates at the boot. Also if you want to force shutdown your phone you can use Vol. Up + Power Button combination for a few secs.
marshalpear said:
OK, so try flashing TWRP to recovery partition to get you out of TWRP after you boot by writing these commands in the ADB:,
fastboot flash recovery recovery.img
fastboot reboot recovery
This will flash the TWRP to recovery partition and will boot you into TWRP. As you do this you won't have a go at the recovery again but for this time. You can reach the TWRP by pressing the Vol. Down button when the phone vibrates at the boot. Also if you want to force shutdown your phone you can use Vol. Up + Power Button combination for a few secs.
Click to expand...
Click to collapse
K, cool feature. Got it all set up now, but back to the main subject:
Is it even possible to install CyanogenMod 12.1 on Sony Z3C?
P9 EVA-L09. I am trying to get original firmware.
The phone was rooted. I relock the bootloader using adb. After that phone has stuck in Huawei eRecovery and can't download firmware.
I use the dload method to perform upgrade. I have downloaded few months ago two zip files.
First copy only the UPDATE.APP (~2GB) file to dload folder on sdcard. Then phone start working. After that from the other zip replace, put the all files
in dload folder. Upgrading was successful, but few apps are missing - camera, contacts and etc -> example ?
Trying this image says: installing updates fails after 10-15%.
Can you suggest me how to fix it or may another image to use?
Thanks in advance !
netaccs said:
P9 EVA-L09. I am trying to get original firmware.
The phone was rooted. I relock the bootloader using adb. After that phone has stuck in Huawei eRecovery and can't download firmware.
I use the dload method to perform upgrade. I have downloaded few months ago two zip files.
First copy only the UPDATE.APP (~2GB) file to dload folder on sdcard. Then phone start working. After that from the other zip replace, put the all files
in dload folder. Upgrading was successful, but few apps are missing - camera, contacts and etc -> example ?
Trying this image says: installing updates fails after 10-15%.
Can you suggest me how to fix it or may another image to use?
Thanks in advance !
Click to expand...
Click to collapse
Did you restore stock ROM (by eg HWOTA) before relocking - because (re)locking invokes Factory reset. There was also another report of similar brick bexause of relocking with rooted or custom ROM.
No I am not. It was stock rom which I rooted.
I am trying several update.app but when processi is complete always something wrong. No all apps installed or keyboard missing and etc.
Can you suggest me what and how to try to install?
I found this link with images.
I am downloading both B136. First I have to copy UPDATE.APP to dload folder on sdcard from update.zip. Then delete update.app from dload
and extract all from B360_update_data_full_hw_eu.zip to dload folder and again perform upgrade (turn off the phone, then holding vol up + vol down + power key
until logo display)
Is that correct?
He guys,
as you've read I bricked my phone and I don't know how or where I did the mistake?
Status before brick:
-) FW: EMUI 8.xxx (not exactly sure which one it was)
-) TWRP: 3.2.3.0
-) Rooted
-) BL: unlocked
-) PHONE Unlock
-) FRP Unlock
What I wanted to do:
-) FW Update to: EMUI 9.0 via FirmwareFinder
What I've done:
-) Did a Titanium Backup
-) Installed Firmware Finder
-) Downloaded the Firmware CLT-L29C432E5R1P9B195 (9.0.0.195) (BUT there were ONLY 2 files)
-) 1. file was "update.zip"
-) 2. file was "update_full_CLT-L29_hw_eu.zip"
-) Renamed the files to
-) 1. kept file name "update.zip"
-) 2. file renamed "update_full_CLT-L29_hw_eu.zip" --> update_all_hw.zip
-) Put the 2 files + hurupdater_04.zip + recovery.img (TWRP 3.2.1.0.img) to a folder in Root on my device
-) Reboot to recovery -> TWRP
-) TWRP -> Install -> hurupdater_04.zip
ERRORS:
-) first I saw a message --> "CLT-L09 "Firmware installing --> how can that happened, if I downloaded the CLT-L29 version?
-) Then it aborted the installing process
Current situation:
-) TWRP is installed again --> TWRP 3.2.1.-0 by Pretorian
-) PHONE Unlock
-) FRP Unlock
-) no OS
!! Cannot access my files either via TWRP or Windows explorer --> all files are encrypted and have totally weird names
So please, please help me installing an OS again!
!! And is there a chance to get access to my pictures back???
I appreciate every helpfull advise.
Thanks in advance!!!
He guys,
nobody has an idea to solve/help me with my issues/situation?
I searched the forum and also other forums and pages to find a solution to "my" problem, but without any helpful results.
I am afraid of doing an eRecovery restore because of losing all my data.
I have currently: TWRP installed -> Files/folders with weird names (shown in TWRP & Phone connected to PC "Explorer")
What can I do to save, restore, copy my pictures and files from phone to PC?
Please give me some hints.
This way brought me back
Try downloading the firmware here: FIRMWARE
Then follow these instructions: HEREhttps://forum.xda-developers.com/huawei-p20-pro/development/huawei-p20-pro-charlotte-l29c432b131-8-t3809964
Got me out of a pinch a few times.
Vedrick said:
Try downloading the firmware here: FIRMWARE
Then follow these instructions: HEREhttps://forum.xda-developers.com/huawei-p20-pro/development/huawei-p20-pro-charlotte-l29c432b131-8-t3809964
Got me out of a pinch a few times.
Click to expand...
Click to collapse
Thanks for the help and the links.
BUT before I'll start doing this, there is just one issue left: the encrypted "storage / files" (pics etc.) in TWRP.
BEFORE I want to say, that I've removed all the security barriers like fingerprint, pattern and faceID !!!!
I tried using this https://forum.xda-developers.com/huawei-p20-pro/development/recovery-twrp-3-2-1-0-t3779400
with different kinds of TWRP versions:
TWRP 3.2.1-0.img
twrp_clt_0.1.img frome here
https://forum.xda-developers.com/huawei-p20-pro/development/recovery-twrp-3-2-1-0-t3779400
twrp-3.2.1-0-charlotte-mod.img frome here
https://forum.xda-developers.com/huawei-p20/how-to/how-to-how-to-unbrick-clt-l29c432-t3878714
twrp-3.2.3-4-charlotte.img
But nothing works, my files shown in TWRP -> storage are still encrypted and still shown with weird gibberish names?
Do you know how to solve this, or where I can get the right TWRP version?
I'm totally at the end of ideas and not finding the right way to get access to my pictures and stuff again.
Da_Hausa said:
Thanks for the help and the links.
BUT before I'll start doing this, there is just one issue left: the encrypted "storage / files" (pics etc.) in TWRP.
BEFORE I want to say, that I've removed all the security barriers like fingerprint, pattern and faceID !!!!
I tried using this https://forum.xda-developers.com/huawei-p20-pro/development/recovery-twrp-3-2-1-0-t3779400
with different kinds of TWRP versions:
TWRP 3.2.1-0.img
twrp_clt_0.1.img frome here
https://forum.xda-developers.com/huawei-p20-pro/development/recovery-twrp-3-2-1-0-t3779400
twrp-3.2.1-0-charlotte-mod.img frome here
https://forum.xda-developers.com/huawei-p20/how-to/how-to-how-to-unbrick-clt-l29c432-t3878714
twrp-3.2.3-4-charlotte.img
But nothing works, my files shown in TWRP -> storage are still encrypted and still shown with weird gibberish names?
Do you know how to solve this, or where I can get the right TWRP version?
I'm totally at the end of ideas and not finding the right way to get access to my pictures and stuff again.
Click to expand...
Click to collapse
I honestly don't think any twrp will work, another reason i'll never buy a huawei again. You could try extracting the image files from the update.app that you get from the update.zip file. then manually flash:
You can extract the image files using EMUI Extractor Application.
fastboot flash cust cust.img
fastboot flash system system.img
I believe the pictures are located on the userdata partition. be sure to flash the right android version as it may depend on what framework you have and how far you got when it was updating. You may want to verify the location of those pictures first.
SO I replicated your soft brick, after I backup up my photos. I ccouldn't save them. I'm up and running though. Turns out I had to first manually flash those image files located in update.app. Then I had to do this
Modified\Updated (Bricked device fix)
1) Try downloading the firmware here: FIRMWARE
2) Extract the update.app file from the update.zip, then use EMUI extractor to extract all the image files. You'll then need to manually flash a few of them: (You can move all these images into the main folder of the Reflash tools located in step 3, then run CMD-HERE)
Commands: (Some might error, i forget which but its alright)
fastboot flash cust cust.img
fastboot flash cache cache.img
fastboot flash kernel kernel.img
fastboot flash recovery_ramdisk recovery_ramdis.img (Very Important)
fastboot flash recovery_vbmeta recovery_vbmeta.img
fastboot flash recovery_vendor recovery_vendor.img
fastboot flash vbmeta vbmeta.img
fastboot flash vector vector.img
fastboot flash system system.img
fastboot reboot, unplug the USB-C cable and hold the volume up button. this will put you into recovery mode.
Then you'll need to format data using with the EMUI recovery and if given the option format cache.
Reboot back into bootloader\Download mode.
3) Then follow these instructions: HEREhttps://forum.xda-developers.com/huawei-p20-pro/development/huawei-p20-pro-charlotte-l29c432b131-8-t3809964
Got me out of a pinch a few times.
Unfortunately I seem to have the same issue. I followed @Vedrick's tutorial.
However after fastboot reboot I'm stuck on 'Your device is booting now...'
Any ideas?
I worry that perhaps the 'boot image' on my p20 is messed up. However in the .APP file I can't find the boot image to restore. I do however see 2 SYSTEM images.
nvm! Got it! Had to fastboot erase userdata.