Database Develop

Boot loop problem

Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.

A few questions:
spazlon said:
I tried installing a custom ROM on my 7310 and it had issues.
Click to expand...
Click to collapse
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop.
Click to expand...
Click to collapse
How far into the boot sequence does it get?
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Have you tried seeing what is causing the boot-loop using adb?
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Click to expand...
Click to collapse
This is an action of last resort. Exhaust all other avenues first.

boscorama said:
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
Click to expand...
Click to collapse
I used CWM to flash AOSP 4.1.2. It seemed to work fine for a day or two, but then it needed charging (as normal). I let it charge over night and in the morning it had less battery. I figured the charger or cable were flaky so I tried another set on another outlet and same thing. Then it finally ran out of battery. I let it charge again over night and when I tried to turn it on it was really slow. The boot animation was only 1 frame every couple seconds. It would eventually boot all the way up, but it was still REALLY slow. So I went into CWM and reflashed the same ROM. Then I got a boot loop of the boot animation. I couldn't get into CWM any more, so then I went into download mode and flashed the official firmware and flashed it with ODIN.
boscorama said:
How far into the boot sequence does it get?
Click to expand...
Click to collapse
Now when I turn it on it just says, "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I can flash again with ODIN and it will get to the Samsung boot animation and just pulse SAMSUNG.
boscorama said:
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Click to expand...
Click to collapse
If I hold power and volume down I can get into download mode or Samsung recovery, not CWM, and power with volume up doesn't do anything.
boscorama said:
Have you tried seeing what is causing the boot-loop using adb?
Click to expand...
Click to collapse
I don't know anything about adb and I'm not sure what I would be looking for. Is there a tutorial I can follow somewhere?
Thanks for any help!

This worked for me with similar problem
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.

Thanks! I'll give this a try when I get home. I'll let you know how it works out.

Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app

jd1639 said:
Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
Agreed - my procedure avoids manual repartitioning - I tried lots of other procedures but none worked. I think my data partition had become corrupt because I kept getting error messages. My first try was to recover with my cwm recovery file I made originally but I kept getting back to the boot loop .

spazlon said:
Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.
Click to expand...
Click to collapse
I always got something like that ...
After bootloop just go to recrovery mode then factory riset ... its 100% WORK
Sent from my GT-P7300 using xda premium

I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.

spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
Sorry - being a newbie myself I'm at a loss. It worked a charm for me.

spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
did a format /system before installing the custom roms? This is an important step.

prince93 said:
did a format /system before installing the custom roms? This is an important step.
Click to expand...
Click to collapse
This fixed it. Never had to do it with any of my other devices. CM10 loaded quickly after that. Loving how fast JB is!
Thanks!
Sent from my GT-P7310 using Tapatalk HD

It worked
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
WOw! This fixed my Tablet! thank you ever so much!!

mjramos15 said:
WOw! This fixed my Tablet! thank you ever so much!!
Click to expand...
Click to collapse
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
Gee thanks. This saved my tab. I'd almost given up on it and then voila.

[GUIDE] Nexus 5 - How to Unlock Bootloader, Install Custom Recovery and Root

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Setup, Preparation and Prerequisites
Basic tasks that I may refer to throughout this guide:
Open command prompt - Press Window Key + R, type in "cmd" (without the quotes), and hit enter.
Enter the bootloader - Turn the phone off. Hold volume down + power. The bootloader is also known as fastboot mode.
ADB and Fastboot Installation
Download the full Android SDK here (scroll to the bottom of the page>DOWNLOAD FOR OTHER PLATFORMS>SDK Tools Only) or get a slimmed version containing only the essential components(Thanks @El Daddy)
Link removed since it expired
Extract the zip and place the android-sdk-windows folder on your desktop.
**If you chose to download the slimmed sdk skip to step 5**
Only if you downloaded the full sdk: Go into the android-sdk-windows folder and run SDK Manager.exe. Install the following packages (there are a total of 4 packages):
- Tools > Android SDK Tools, Android SDK Platform-tools
- Extras > Android Support Library, Google USB Driver
Only if you downloaded the full sdk: Go back into the android-sdk-windows directory, and you should see a new folder named platform-tools. If you don't see this new folder, repeat the step above.
To confirm that it is indeed working, open a command prompt window and enter the following commands:
Code:
cd Desktop/android-sdk-windows/platform-tools
adb version
If it displays "Android Debug Bridge version x.x.xx" it is working. If it is gives an error saying that adb is not a recognized command, it has not been successful. Carefully repeat the steps above if this is the case. Close the command prompt window when you are done.
USB Debugging - On your phone go to Settings > About phone > Tap on Build number 7 times. This will enable Developer options. Now go back to Settings > Developer options > Enable USB debugging
Show File Extensions - Open a command prompt window and run "Control folders" (without the quotes). Go to the View tab and uncheck the "Hide extensions for known file types" option. This will help avoid confusion when renaming files.
Battery - Ensure that your phone has at least 60% battery remaining, and that your PC is plugged in and wont shut down spontaneously during the process. The procedure doesn't take very long (5-15 minutes), but its best to have enough charge in case something goes wrong.
Backup (Optional) - Unlocking the bootloader will completely wipe all data from the device. This includes apps, settings and even the contents of the internal sdcard (pictures, music, etc.). Copy all important files off the phone onto a PC or upload them to a cloud.
Driver Installation - Try this first, but if that doesn't work look here. Still having issues? Give this a try. None of these working? Hopefully this does the trick.
Downloads
Download a custom recovery of your choice and the SuperSU zip below. Place both files (recovery image and root zip) in the platform-tools folder located on your desktop within the android-sdk-windows folder.
Custom Recovery:
TeamWin Recovery Project (TWRP) or ClockworkMod (CWM)
Root:
SuperSU
Information
Rooting a nexus device is actually quite a simple and easy process. Before you begin, it is recommended that you at least try to understand what each part of the process will do. Although this guide will elongate each step in order to show all of the details, the method used can be broken up into 3 main steps: Unlocking the Bootloader, Installing a Custom Recovery and finally Rooting. Each new step relies on the previous step to have been completed, and a basic summary of each part is:
Unlocking Bootloader: Opens the door to the internal memory of the device to be written on to. This allows you to flash images onto the main partitions of the phone.
Installing a Custom Recovery: A custom recovery is flashed onto the recovery partition of the device and overwrites the stock recovery that exists by default. Custom recoveries bring lots of functionality and give you the ability to perform wipes, install flashable zips, create full backups of your NAND (Nandroid backup), and various other features. An unlocked bootloader is needed to install a custom recovery.
Rooting: You can gain root by either flashing via recovery a pre rooted custom rom, or flashing a zip containing the SuperSU binaries. A custom recovery is necessary to do this.
After completing these steps your phone will be rooted, the phone will have a custom recovery installed, and the phones bootloader will be unlocked. This, in my opinion, is the most practical and beneficial method for rooting your phone. It gives you some basic adb/fastboot knowledge, and should hopefully help you have a decent understanding of what is going on. Also this method will work regardless of what android version your phone has. Using a toolkit will only make things worse in the long run...learn to do it properly. It has been proven that every time you use a toolkit, god kills a kitten. Save the kittens.
If you are confused by anything in this guide, I would highly suggest getting it clarified being before moving on. Ask your question in this thread and I or someone else will likely answer. Also I'd suggest that you read over the whole thread a few times before actually doing anything to the phone.
Understand? Good...lets begin:
1. Unlocking Bootloader
Turn the phone off. Then boot it into the bootloader/fastboot mode by holding volume down + power.
Plug the phone into your PC, then open a command prompt window window and type:
Code:
cd Desktop/android-sdk-windows/platform-tools
Code:
fastboot devices
This command will list the connected devices. If your phones serial number shows up you are good to go and may continue. If the phone is NOT listed this indicates that your drivers are not installed correctly. In order for you to continue you must fix your drivers so that your phone is listed under fastboot devices.
If the phone has been recognized by the command above, proceed to unlocking the bootloader with the following command:
Remember that this step will wipe EVERYTHING off the phone
Code:
fastboot oem unlock
On the phone a screen should pop up asking whether or not you would like to unlock the bootloader. Use the volume rockers to highlight "Yes" then press power to confirm the action.
After the above command has finished excuting, run the following (DO NOT skip this step, it is more important than you think):
Code:
fastboot reboot
The phone will reboot. Next you will be presented with a screen containing an android logo and a progress bar (this may take up to ten minutes to complete). Wait until the phone has fully booted up into android, then proceed onto the next section of the guide.
Close the command prompt window.
2. Installing a Custom Recovery
Turn the phone off. Then boot it into the bootloader/fastboot mode by holding volume down + power.
Rename the recovery file that you downloaded above to recovery.img. *Make sure that you rename it to recovery.img NOT recovery.img.img* Remember that you should place the file in the platform-tools folder inside of the android-sdk-windows folder on your desktop.
Open command prompt and run the following commands:
Code:
cd Desktop/android-sdk-windows/platform-tools
Code:
fastboot flash recovery recovery.img
On the phone, use the volume buttons to scroll onto "Restart Bootloader" and hit power to select it. After the bootloader reloads, use the volume buttons to scroll onto "Recovery Mode" and power to select it. You should then be greeted with your newly installed custom recovery.
Close the command prompt window.
3. Rooting
Now that your phone has an unlocked bootloader and a custom recovery installed you have a two options to gain root (Pick one or the other. You don't need to do both)
Option A) Flash SuperSU binaries which will give you root with the stock rom
Confirm that you have downloaded the SuperSU zip from the downloads section above and that it is located in the platform-tools folder inside of the android-sdk-windows folder on your desktop.
Turn the phone off then boot into the bootloader. (volume down + power). Once in the bootloader use the volume rockers to scroll onto Recovery Mode, then press power to select it. This should bring you into your newly installed custom recovery. Leave the phone at the home page of the custom recovery.
Open a command prompt window and run the following commands:
Code:
cd Desktop/android-sdk-windows/platform-tools
Code:
adb push UPDATE-SuperSU-v[COLOR="Red"]X[/COLOR].[COLOR="red"]XX[/COLOR].zip /sdcard/
This will copy the SuperSU zip onto your phone. Once the command has completed continue.
Instructions for TeamWin Recovery Project (TWRP):
Install > browse to SuperSU zip and select the it
Swipe to confirm the installation. Then reboot.
Instructions for ClockworkMod (CWM):
install zip from sdcard > choose zip from sdcard.
Next, browse to the location where you previously copied the SuperSU zip and select the it.
To confirm the installation, scroll down to "Yes" and select it. The installation shouldn't take very long, and once it has completed you may reboot.
Option B) Flash a custom rom which will come pre-rooted
Note that not all custom roms will be pre rooted, however the majority of them are. Read the OP of the ROM thread to see what the verdict is.
Copy a custom rom (you can find these in the Nexus 5 Android Development and Nexus 5 Original Android Development section) onto the phone (remember the location where you copy it to)
Turn the phone off then boot into the bootloader. (volume down + power). Once in the bootloader use the volume rockers to scroll onto Recovery Mode, then press power to select it. This should bring you into your newly installed custom recovery. To install a custom rom the general procedure to follow is: factory reset, wipe cache + dalvik cache, flash ROM, flash GApps. Here are the recovery specific instructions:
Instructions for TeamWin Recovery Project (TWRP):
Wipe > Swipe to Factory Reset
Install > browse to the location where you previously copied the ROM zip and select it > Swipe to confirm the installation
Install GApps using same process as ROM, then reboot.
Instructions for ClockworkMod (CWM):
wipe data/factory reset
wipe cache partition
advanced > wipe dalvik cache
install zip from sdcard > choose zip from sdcard > navigate to the location of the rom > select the rom > confirm the installation by selecting "Yes"
After that you may install the GApps using the same method for flashing the rom, and finally reboot the phone.
Keep in mind that the first boot after installing a custom rom & wiping the phone may take longer than usual, as the phone will need to rebuild the dalvik cache and initialize other first boot stuff.
Congrats! That is all! Your phone now has an unlocked bootloader, a custom recovery installed and is rooted...Plus you saved a kitten. Enjoy

Troubleshooting & FAQ
Why am I seeing a red triangle with a dead android when booting into recovery even after I flashed a custom recovery?
What you are seeing is the stock recovery, meaning that the custom recovery that you flashed did not install correctly. Try the following suggestions:
Make sure you are using the USB cable that came with your phone. Only use other ones, if the stock one isn't working
Try using different USB ports. USB 2.0 ports (the ones that ARE NOT blue) are preferable. USB 3.0 ports (the blue ones) may cause problems with connectivity.
If you are on a desktop, use the ports on the back of the tower instead of the ones in the front. These ports are directly connected to the motherboard, rather than the ones in the front which are usually attached to a header cable which then indirectly connects to the motherboard.
My phone wont boot into android. I can only access the bootloader and custom recovery. What do I do?
Suggestion 1: Factory reset via recovery.
TWRP Instructions:
Boot into recovery
Wipe > Swipe to Factory Reset
Reboot
CWM Instructions:
Boot into recovery
wipe data/factory reset
wipe cache partition
advanced > wipe dalvik cache
Reboot
If that doesn't work continue onto Suggestion 2.
Suggestion 2: Push a ROM to your phone and flash it.
Download a ROM onto your computer. If you don't have time to look for a ROM, just download the stock ROM.
Move the downloaded ROM onto your desktop, and rename the file to "ROM.zip" (without the quotation marks)
Boot phone into recovery
Open command prompt and run the following commands:
Code:
cd Desktop
adb push ROM.zip /sdcard/
Wait for it to finish copying the file, then flash the ROM. If you need further details on how to flash a ROM take a look at the OP, section 3. Rooting, Option B)
If that doesn't work continue onto Suggestion 3.
Suggestion 3: Flash the factory images.
Flash the factory images
My phone wont boot into android. I can only access the bootloader. What do I do?
Flash the factory images
My phone exploded. What do I do?
Tape it back together then flash the factory images

Awesome post. Got a question: if I ONLY unlock bootloader will I still be able to get and install OTA updates?
Sent from my Nexus 4 using Tapatalk

dombera said:
Awesome post. Got a question: if I ONLY unlock bootloader will I still be able to get and install OTA updates?
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Yes, if you only unlock the bootloader you will still be able to get ota's. The lock state of your bootloader will not affect your ability to receive ota's.

Chromium_ said:
Yes, if you only unlock the bootloader you will still be able to get ota's. The lock state of your bootloader will not affect your ability to receive ota's.
Click to expand...
Click to collapse
Awesome, thx
Sent from my Nexus 4 using Tapatalk

This is awesome, will come in handy.
Sent from my HTC Desire using XDA Premium 4 mobile app

Chromium_ said:
Yes, if you only unlock the bootloader you will still be able to get ota's. The lock state of your bootloader will not affect your ability to receive ota's.
Click to expand...
Click to collapse
What about if you unlock the boot loader and root, will you be able to get OTAs then? I guess a better question is what's the point of no return (without reflashing the factory image) where you break OTA updates? Thanks for the thread btw!

Can people please post confirmation of TWRP or CWM recoveries + rooting working without problems if they've done it? I know it's unofficially supported at this time, but getting some data collected would be useful.
---------- Post added at 01:43 AM ---------- Previous post was at 01:41 AM ----------
Xero258 said:
What about if you unlock the boot loader and root, will you be able to get OTAs then? I guess a better question is what's the point of no return (without reflashing the factory image) where you break OTA updates? Thanks for the thread btw!
Click to expand...
Click to collapse
If you unlock bootloader & root, and modify some system files, OTAs may not be able to pass some pre-install checks, at least this has happened to me on N4 before. I added one line to /etc/build.prop, also one of the older SuperSU versions had to be uninstalled for pre-install OTA checks to pass.

Whyzor said:
Can people please post confirmation of TWRP or CWM recoveries + rooting working without problems if they've done it? I know it's unofficially supported at this time, but getting some data collected would be useful.
Click to expand...
Click to collapse
There isn't *yet* a booting custom recovery for the Nexus 5. Give it a couple of days.

I see some Desire folks
Did u order one chromium?

Is unlocking the bootloader going to be the same as on my GNex, where it wipes the device in the process? If so, this will be the first thing I do when I get it out of the box on Monday.

talz13 said:
Is unlocking the bootloader going to be the same as on my GNex, where it wipes the device in the process? If so, this will be the first thing I do when I get it out of the box on Monday.
Click to expand...
Click to collapse
If you wipe cache exactly after you unlock the bootloader, without booting, no.

Nbsss said:
I see some Desire folks
Did u order one chromium?
Click to expand...
Click to collapse
Not yet. Hoping to eventually get it though.

Whyzor said:
Can people please post confirmation of TWRP or CWM recoveries + rooting working without problems if they've done it? I know it's unofficially supported at this time, but getting some data collected would be useful
Click to expand...
Click to collapse
There are currently no working custom recoveries, so it really only makes sense to unlock the bootloader for now. That way you'll be ready to continue on with the guide right when a stable recovery is released.
Sent using xda-developers app

Nbsss said:
I see some Desire folks
Did u order one chromium?
Click to expand...
Click to collapse
I'm not a really famous desire user but yes I bought it. Did you buy it to? Happy to see some other desire users.
Sent from my HTC Desire using XDA Premium 4 mobile app

Maybe it's a silly question, but can I unlock the bootloader before even booting up the phone for the first time? Can this cause some problems?

boysetsfire said:
Maybe it's a silly question, but can I unlock the bootloader before even booting up the phone for the first time? Can this cause some problems?
Click to expand...
Click to collapse
It should work fine, but whats wrong with booting it up for the first time?

Chromium_ said:
It should work fine, but whats wrong with booting it up for the first time?
Click to expand...
Click to collapse
Nothing wrong, just the laziness of not wanting to do the initial setup two times

Chromium_ said:
There are currently no working custom recoveries, so it really only makes sense to unlock the bootloader for now. That way you'll be ready to continue on with the guide right when a stable recovery is released.
Sent using xda-developers app
Click to expand...
Click to collapse
abaaaabbbb63 said:
There isn't *yet* a booting custom recovery for the Nexus 5. Give it a couple of days.
Click to expand...
Click to collapse
Ok, the wording in OP is:
"Currently neither recovery has official support for the Nexus 5, so the download links below are unofficial and may not be functioning 100% correctly."
and:
"**Warning: Currently there are no officially stable custom recoveries, so i would only recommend unlocking the bootloader for now**"
Which implied that it does work, just not thoroughly tested. Now from the recent replies you're saying it DOES NOT boot at all into recovery?

Whyzor said:
Ok, the wording in OP is:
"Currently neither recovery has official support for the Nexus 5, so the download links below are unofficial and may not be functioning 100% correctly."
and:
"**Warning: Currently there are no officially stable custom recoveries, so i would only recommend unlocking the bootloader for now**"
Which implied that it does work, just not thoroughly tested. Now from the recent replies you're saying it DOES NOT boot at all into recovery?
Click to expand...
Click to collapse
Yes that is correct, they do not boot. I will update the OP now, sorry for the confusion.
Originally I had read the following threads and it seemed that they were somewhat functioning, but it is now confirmed that neither one boots.
TWRP
CWM

[Q] Full tutorial to put KitKat on N1. Who wants to test?

Hi all, I wrote a long-winded Tutorial to put Evervolv KitKat on a stock N1. I don't have a stock N1 (I stumbled all the way through this process and got done yesterday, was so excited I wrote this tutorial) and don't know how to get it back to stock, so I'm wondering if anyone who has one and has experience putting new ROMs on other devices would like to test this out and let me know if anything doesn't work as written. Please go ahead if you like and reply your updates! Once it's dialed I'll make it a thread in the N1 ROMs forum.
Here's the text:
How to put KitKat on a Nexus One (And have computing power & space to spare):
Things you'll need:
1. A Windows/Linux computer with internet connection, USB port, and terminal
2. A USB Cable
3. A Nexus One with the most recent stock gingerbread rom (Settings->about, look for Android 2.3.6 or GRK39F, else apply/google updates to get to that version)
Before you begin, note that you're playing with a generally safe form of fire, but when playing with fire, you may brick your phone. The maker of this guide and any sites you visit during the process assume no responsibility, the user assumes full responsibility for lost work and damaged or ruined phones. Your warranty will be voided about six times over. Save all your stuff somewhere, save apps with Titanium Backup (Google it) or something, and do a full Nandroid backup (Goog that too) before you begin. You will be fully wiping your phone and SD card multiple times. Make sure at every step of the process that your battery is at least half full. Running out of battery during an update can cause bricks. In this guide, “Boot” means standard boot, the way it normally turns on. Not hboot or fastboot or recovery.
I did part of this from a Windows7 computer on Cygwin and part on Ubuntu 12.04, each presented some annoyance but by far the greatest was due to my Linux ineptitude with PATH and Root. If you're trying the same, I've made an appendix for that.
It may help to have a brief conceptual overview of what you'll be doing in case you run into snags and have to step out of the walkthrough. Your N1 has a few basic parts: Internal memory that is chopped into 3 partitions: One for the system files (System) , one for the files that they will need to make during the first bootup and use in order to operate, along with your apps and their created files (Data) and one for temporary files that your OS and apps can regenerate (Cache). Somewhere in there it also has space for a Radio (that also includes some critical power functions, flashing a new radio is the easiest way to brick an N1 but we won't), as well as a Recovery partition and an Hboot&Fastboot partition. We will be messing with Recovery and Hboot. The virtual machine that turns all the friendly pseudo-english computer code into 1s and 0s for the processor to deal with is called Dalvik, named after a town in Iceland where some old dev's family is from. It has its own Cache (the VM, not the town, as there are no longer any fish in Iceland ). It's SOP to wipe Cache & Dalvik before and after applying any updates, and wipe Data (Factory reset) before applying most updates. Sometimes when my phone bogs I reboot to recovery and wipe caches just for funsies. This makes it take longer to boot the phone and to use each app just the first time after that, while the files are created fresh. The phone also should have an SD-Card. You should have or buy an 8+MB, Class 10 SD card. The class relates to read/write speed, anything less than 10 will noticeably slow your Nexus One's operation. Why?
Because we're going to put some of your operating system on the SD card. We're going to use a special recovery system (aka recovery ROM) called “4ext” to partition your SD card. Mine is 16GB, partitioned to 14GB for storage and 2GB to use as fake internal memory, where my system's Data and Cache live. The KitKat System files that normally live on internal memory's System partition are too big for a normal N1, so we'll use a special Hboot called BlackRose to repartition your internal memory so you can fit KitKat, and then after you first boot it up we'll use an app called Mounts2SD to install a startup script so that every other time you boot it up after that, it will know to find Data and Cache on the SD card. In order to install BlackRose, you'll need to be running CyanogenMod Rom as your main OS, and in order to do that you'll need ClockWorkMod Recovery ROM. So the installation order will be: ClockworkMod recovery->Cyanogen7OS (Gingerbread based)->4ext recovery to partition SD card->BlackRoseHboot to repartition internal memory->Evervolv KitKat-based N1 ROM-> run Mounts2sd for startup scripts ->reboot to your new life among the anatomically modern cyborgs (and then you're on your own for getting all your apps and music and contacts and stuff back on the phone from wherever you saved it).
Ready? Here we go!
1. Install the Android SDK on your computer.
1. Get the appropriate version here: http://developer.android.com/sdk/index.html
2. Unzip it.
3. Run the setup.exe (if using windows)
4. When asked which packages to install, choose “Android SDK Tools”, “SDK Platform Android 2.1″, and “Usb Driver package” (If you use eclipse, check that last link for instructions on using the ADT plugin (Not the same ADT that cuts your paycheck, much less inept))
5. Make sure the USB drivers installed properly (windows).
1. Go to printers and devices in the control panel, or device manager
2. If you see an android device with no warnings, you're golden. If it has warnings, right click it and go properties->update driver (driver can be found in your android sdk directory where you unzipped the sdk bundle, in \usb_driver).
6. Boot up your N1 and plug it in to the computer. If the computer recognizes it and they play nice, you're set with the sdk. To extra check, open terminal and cd to the sdk's platform-tools folder that should contain the adb utility. Type #adb devices and see if it comes up with a message telling you that it's running a daemon on a port like 5037, and then lists something like HT9CPP800063 device. This is your phone, it's telling you you're beyond connected. You've got the sdk working. Else have your friend Google help you get the SDK properly installed.
2. Root the phone so it will let you dig in.
1. Put your N1 in USB debugging mode (Settings > Applications > Development > USB Debugging)
2. In the terminal, in the platform-tools folder, type #adb reboot bootloader. (((My phone has a power hardware issue and will not reboot while plugged in ever to any mode ever at all ever, if yours does too you can unplug (first type #adb kill-server to make it ok to unplug) the usb cable, power down, wait five seconds, and hold the trackball and power button to power back up into the bootloader, then plug in again. There was a lot of unplugging, waiting fifteen seconds, booting while holding buttons, plugging in, adb devices -ing that I will omit henceforth due to low likelihood that you have the same problem.)))
3. Using the onscreen directions on the phone and the hard buttons, navigate to fastboot mode. It may be unresponsive and throw some not-found messages for five seconds before it lets you do anything.
4. In the terminal on your computer, in the platform-tools folder, type #fastboot devices to see if your devices is connected (it should come up with the same HT#XXX###### number).
5. This step will gain Root access, unlock the bootloader, and WIPE ALL YOUR ****. Now type #fastboot oem-unlock . You may have to accept the warranty voiding. If for whatever reason it doesn't work, use this method http://code.google.com/p/bexboot/, and unzip the files to the platform-tools folder.
6. Using the phone buttons, reboot. Your little lock logo during the bootup should be unlocked now.
7. Power down and boot again for good measure. Re-enable usb debugging in the phone app dev settings.
3. Get ClockworkMod Recovery.
1. Download koush's ClockworkMod Recovery from : recovery-clockwork-5.0.2.0-passion.img and put it in the platform-tools folder.
2. To make sure the file is not corrupted and will not brick your goods, check the md5sum. This is the result of a complicated equation that easily reveals even a single flipped bit in the file by vastly changing the output. Google how to do this, in windows you'll need to download a tool like winmd5free. The output for this particular file should be: md5: 45716c8d51ed2375873f01f0b14b2184 If it's anything else don't use it.
3. Reboot to the bootloader again, either by #adb reboot bootloader or by powering up while holding the trackball, and navigate to fastboot.
4. Verify that you're connected with #fastboot devices
5. Flash ClockworkMod Recovery by typing #fastboot flash recovery recovery-clockwork-5.0.2.0-passion.img
6. It should give a success message. Reboot to recovery from the fastboot menu. It should be a sweet new blue and white ClockWorkMod recovery. Power down and reboot to recovery by holding volume up as you power up, just for good measure.
4. Get CyanogenMod7 ROM.
1. On your computer, go to http://download.cyanogenmod.org/?device=passion&type=stable and download the latest stable CM7 zip. Put it in the platform-tools folder.
2. Check its md5 as you did in part 3.
3. Do #adb-devices, which should give you that serial again, and the word recovery.
4. Place the zip file on the root of your SD card by doing #adb push cm-7.2.0-passion.zip /sdcard/
5. If that last step failed, try running #adb shell mount /sdcard or #adb kill-server then #adb devices then #adb shell mount /sdcard, then try the push again. Or mount the sdcard through the recovery menu before running that push command. Or use your computer's file system to drag and drop the .zip to the root (lowest) folder of the sd card.
6. Using the recovery menu, in backup and restore options, backup your current ROM.
7. In the format menu, do a wipe data/factory reset. Wipe the cache and dalvik cache while you're at it.
8. Back in the main recovery menu, do install zip → choose zip from sd card.
9. Select that CM7 zip file.
10. Return to the main menu and reboot the system. It should come up with a totally different looking leaner meaner version of Gingerbread, that gives you more control and speed and saves battery. But even with this system, given modern app sizes, you'll soon run out of room on the internal memory if you stop now. And besides, you're having too much fun.
5. Get 4EXT recovery
1. Go to 4ext.net and download the free .apk file: http://www.4ext.net/get.php?apk Congratulations if you're about to install your first not market app (apps are now .apk, not just something you get from the store's GUI.). Save it in platform-tools. Or, to be really nice to Max, you can just buy the app in the play store and skip the next two steps.
2. Enable USB debugging, plug in and #adb-devices.
3. # adb install 4EXTRecoveryUpdater.apk. You should get back a success message in a fistful of seconds.
4. At this point you may need to back out to regular settings, turn on wifi, and hook up to your wifi router.
5. Open the 4ext recovery updater app. Go to settings. Allow superuser permissions and everything else. It should detect Nexus One, connect to the internet, and boot you back to the main menu.
6. Go to online install. They're all release candidates and no stable versions, so just go with the newest one. Select install.
7. Wait for it to finish and then reboot to recovery, either by # adb reboot recovery or manually. You should have a beautiful new touchscreen recovery.
6. Partition your SD Card
1. In recovery, go to tools->partition sd card->remove all partitions and start from scratch.
2. For the first Ext partition, where you'll be keeping a good chunk of your OS, The consensus online is not to go above either 1.5GB or 2GB. I'm working fine with 2GB aka 2048MB.
3. You can skip the 2nd Ext partition.
4. The internet says Swap size should be 0.
5. Internet says File system should be ext4. This should do the partitioning, the rest of your SD card will still be great for storage as before.
7. Repartition internal memory using BlackRose:
1. I have never used BlackRose on Windows, but here goes: go here : http://forum.xda-developers.com/showthread.php?t=1270589 and download this zip archive: http://forum.xda-developers.com/attachment.php?attachmentid=1016437&d=1334971685; It has windows and linux files. The site also has a manual in case this walkthrough lets you down.
2. Unzip it into a folder in your platform-tools. Execute it with a ./ in linux or a .exe in win. It should say waiting for devices.
3. Reboot your phone manually. BlackRose should hijack the startup, install itself, and quit. Boot your phone up again.
4. Blackrose is rumored to have an interactive guide to partitioning, but it didn't work for me and at least some other genius on the internet, but being an industrious Austrian, he figured out the fix: Run Blackrose in Editor mode. Type resize as prompted.
5. The post here http://forum.xda-developers.com/showthread.php?t=2540366 on Evervolv KitKat implies that 250MB for System works with enough space for Gapps (Google does not allow their standard apps like Play Store to be included with Mod roms anymore, so you will need to install them from recovery too, but they distribute them bundled so it's not hard.), and some commenter said 260MB, but that didn't work for me long enough to run startup scripts and move some of it off. So I had to redo it and I went with 265MB for System and 10MB for Cache, which is working fine. Give it a name, I went with Kat.
6. BlackRose will shut down, but it will leave a golden turd in the form of a file called hboot_brcust.nb0 probably in the folder called “other.” That's what you want.
7. Put that file in the same folder as the Blackrose utilities fastboot-l and fastboot-w if it's not already there. Then boot your phone into fastboot again, via adb or manually. I think. Maybe try this from being standard booted up if the next part doesn't work.
8. Run # fastboot-l flash hboot hboot_brcust.nb0 . Windozers should use fastboot-w instead. Blackroot will wait for the device again.
9. Reboot your phone into the bootloader manually, by holding the trackball while powering up. The image should install on this boot, resizing your phone's internal memory partitions.
10. Run # fastboot -w. Your Bootloader should be loaded up, with the 1st line saying something about BlackRose and the 2nd line saying 265/10/161. This is how you know it worked. That 265 is where it's at for KitKat. Your main OS had been destroyed, but your Recovery ROM should still work.
8. Install Evervolv KitKat.
1. Go here http://evervolv.com/devices/passion and download the latest stable release. At press time that's the 4.0.0p4.2 version. Save it to platform-tools.
2. Reboot to Recovery from the menu in the BlackRose bootloader.
3. Do # adb devices. Then do # adb push ev_passion-4.0.0p4.2-perdo-squished.zip /sdcard/ . If it doesn't work, try using the touch recovery menu to toggle mount USB, then push, then unmount. Or mount USB, use the computer's file system to move the file to the root of the sd card, then unmount USB. Or try as root if you're using linux.
4. From the main recovery menu, select install zip from SD card → choose zip → select the ev_passion-4... zip. Wait up, it could take a while.
5. Success!! Right? Right. #adb kill-server, you can unplug now and won't need to plug back in! Reboot the phone, you're getting perilously close! This boot could take five plus minutes, or just one, but be patient.
9. Install Gapps.
1. You are such a lucky dog. Gapps bundled updates are available through the Evervolv toolbox. So you can get Play Store and everything else will come easy. Go to settings → wifi, turn it on, hook it up to your wifi router.
2. Back up to settings, and go Evervolv Toolbox → Updates and swipe over to the Gapps section. Tapp the most recent Gapps-kk zip. Tap the down arrow to download.
3. Reboot manually to recovery.
4. From the main recovery menu, select install zip from SD card → choose zip → select the gapps-kk... zip. This could also take a sec.
5. Reboot again! You're almost done! When it's all loaded up, Play Store should now be installed, as well as various google options that you can enable through the Evervolv settings.
10. Install Mounts2sd.
1. Go to the Play Store and get Mounts2sd.
2. Hit the top right corner for application settings. You'll need to install a startup script. Agree, give it permanent superuser status.
3. Reboot.
4. Go back into Mounts2sd, and go to the Tool menu (Wrench). Note that boxes aren't checked unless they're green-checked.
5. Enable the Cache to move cache partition to data or sd-ext. Storage threshold is up to you. Make sureApplications, Libraries, Data, and Media are all checked. Dalvik should stay unchecked, System apps can too.
6. Reboot again.
11. You're done!!! Or at least we're done. You still have to restore your apps and put all that music back on and figure out how to resync your contacts and... Good Luck.
12. If you want to get extra tricky, it's believed to be possible to leave app data on the real internal memory by default, and use Titanium Backup to move the data of most of your apps to the SD-ext, thereby leaving the data of your favorite apps on real internal memory. Use at your own risk.
ENJOY!!
Appendix 1:
Linux PATH env: I put all my android stuff in a file called androidy, so my path to my platform-tools was /androidy/adt/sdk/platform-tools, and my blackrose was in there too. So to set my PATH, I used: $ export PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/home/sean/androidy/adt/sdk/platform-tools:/home/sean/androidy/adt/sdk/platform-tools/blackrose_120421/binary"
In order to make sure that while using it as root (as was necessary for some fastbot operations), I referenced the same PATH instead of the messed up root PATH, I used sudo env PATH = $PATH a few times.
Appendix 2:
The only actual bug I've noticed in a few days with this ROM is that my Chrome bookmarks don't add shortcuts to the homescreen when I tell them to from within Chrome. The widget-adder (longpress homescreen) has a bookmark option though, so if you bookmark it you can put it on the homescreen from there.
Huge Thanks to everyone involved with ClockworkMod, Cyanogen, 4Ext, BlackRose, and Evervolv!
Sources:
http://wiki.cyanogenmod.org/w/Install_CM_for_passion
http://nexusonehacks.net/nexus-one-...n-how-to-unlock-bootloader-on-your-nexus-one/
http://marian.schedenig.name/2012/07/22/installing-android-4-ics-on-the-google-nexus-one/
http://forum.xda-developers.com/showthread.php?t=2540366&page=24

Wooooh, Amazing book ! Everything is soo.... deep. In my opinion, tutorials should be only few lines.
Some mistakes :
Why installing CM7 and then backing up ? (You can install non market apps without CM7, and when flashing CM7 you erase all user data)
Why using m2sd if the rom has a built-in feature called a2sd ?
Why installing CWM then 4EXT recovery ? (TWRP is a touch one, and you can flash recovery once you have root access)
"You should have or buy an 8+MB, Class 10 SD card" ? typo ?
In my mind, big steps should be :
1) Backup SD, and SMS and Apps
2) Root
3) Install recovery (TWRP is advised by evervolv, but CWMRecovery is OK)
4) Partition SD
5) Install Blackrose (using 260mB system)
6) Flash ROM
7) Flash GAPS
8) A2SD Y N Y
Notes :
About SD-Ext size, i recommend reading this post from his creator : http://forum.xda-developers.com/showthread.php?t=1716124
A2SD is an old version of INT2EXT+
Using terminal is not friendly for beginners. Avoid it at maximum.
Provide a link for a MD5 sum checker.
I don't know if it works with actual stock rom, but when i rooted my n1, i used SuperOneClick. Plug, Click, Wait, Smile. (I still have it if needed)

ldFxl said:
In my opinion, tutorials should be only few lines.
Click to expand...
Click to collapse
This tutorial doesn't need to exist at all. All the information is available elsewhere on the internet, I did nothing original. Its only value is that it puts all the information in full detail in one place so you don't have to look in the forums for elaboration on each line of a more concise tutorial. Hopefully with info this detailed, someone with more chops than me could script it.
ldFxl said:
Why installing CM7 and then backing up ? (You can install non market apps without CM7, and when flashing CM7 you erase all user data)
Why using m2sd if the rom has a built-in feature called a2sd ?
Click to expand...
Click to collapse
I had already installed CM7 when I thought to write this, Marian (my 3rd source) seems pretty skilled as he is the only one who could make BlackRose work for me so I trusted his advice that it was the easiet procedure he found. Have you put TWRP Recovery on from stock after unlocking the bootloader (fastboot oem unlock)? And have you successfully repartitioned SD (fat32 &ext4) from TWRP? If so and you want to quickly write up the steps, I'd gladly replace my steps 3-6, that would save people a lot of time and doing.
ldFxl said:
Why installing CWM then 4EXT recovery ? (TWRP is a touch one, and you can flash recovery once you have root access)
Click to expand...
Click to collapse
4EXT is also touch, CWM cannot repartition SD. If you can go stock to TWRP this might be the best option. Or if not, stock to 4ext.
ldFxl said:
"You should have or buy an 8+MB, Class 10 SD card" ? typo ?
Click to expand...
Click to collapse
Yes! Thanks.
ldFxl said:
Using terminal is not friendly for beginners. Avoid it at maximum.
Click to expand...
Click to collapse
Don't you have to use terminal to use the built in A2SD? At any rate, it didn't work for me (I'm kind of a beginner), Mounts2SD's GUI seemed a little more beginner friendly. Also I certainly wouldn't have been able to make BlackRose work
ldFxl said:
Provide a link for a MD5 sum checker.
Click to expand...
Click to collapse
Good idea
ldFxl said:
I don't know if it works with actual stock rom, but when i rooted my n1, i used SuperOneClick. Plug, Click, Wait, Smile. (I still have it if needed)
Click to expand...
Click to collapse
I once used SuperOneClick on another phone, it looked like it struggled and finally worked with a DDoS style attack, it seemed simpler to just do it the way the manufacturer intended (if that's even a thing). But I suppose if it works with one click it really is simpler as seen by the user. Anyone have a report on whether it worked from stock N1?

Fituate said:
I had already installed CM7 when I thought to write this, Marian (my 3rd source) seems pretty skilled as he is the only one who could make BlackRose work for me so I trusted his advice that it was the easiet procedure he found. Have you put TWRP Recovery on from stock after unlocking the bootloader (fastboot oem unlock)? And have you successfully repartitioned SD (fat32 &ext4) from TWRP? If so and you want to quickly write up the steps, I'd gladly replace my steps 3-6, that would save people a lot of time and doing.
Click to expand...
Click to collapse
On my first flash, i was pretty beginner, so i followed a tutorial ; ) . And they used CWM. But flashing a recovery procedure from .img file doesn't differ with the recovery. TWRP allows you to partition SDCard. I did it last week (on HTC wildfire S, TWRP 2.6 as for N1).
Flashing step is the same -> just replace img file name. You can get it Here (From official TWRP Website)
Procedure from TWRP Website said:
Download the above file. Turn off your device. Turn on the device and keep holding volume down until a menu shows up. Select fasboot from the menu list. Plug the device into your computer. If you have the right drivers installed, your screen should now say FASTBOOT USB. Run the following command via the command line:
fastboot flash recovery recoveryfilename.img
Note that you will need to change the last part to match the name of the file that you just downloaded. This method requires that you have the drivers installed that come with the HTC Sync software that are available here. You will also need adb and fastboot for your computer.
Click to expand...
Click to collapse
6. Partition your SD Card
1. In recovery, Tap Advanced
2. Tap Partition SD Card
3. Set 2048 (MB max) on EXT Size and 0 on Swap Size
4. Tap EXT4 then swipe to start partitioning
Fituate said:
3. Reboot your phone manually. BlackRose should hijack the startup, install itself, and quit. Boot your phone up again.
Click to expand...
Click to collapse
Backrose is a custom Bootloader-> it replaces your HBoot/Fastboot
You don't need to reboot your phone to install blackrose. You just need your phone in ADB over USB, then the win setup will install blackrose.
Once done, run setup again, your phone will automaticaly go to HBoot, then choose 1, and 1 again.
Then enter "resize", "260" and "8".
In case that the installer don't work correctly, you can get flashable HBOOT from [Provide a nb0 (texasice recommend 260/8/168) AND MD5 Checksum]
While googling to find some infos (I don't remember me unlocking my bootloader) I found this guide : http://forum.xda-developers.com/wiki/HTC_Nexus_One/Flashing_Guide
Apperently SuperOneClick does not even need unlocked bootloader on 2.3.3 or previous ...
Isn't what we are trying to write down ?
There are many links pointing to this forum aswell.

Newbie-friendly: TWRP and Root for Tab A tablets (2016, 10.1")

Tested SM-P580, SM-T580, SM-P585
This post is designed to gather information found across this forum to give a step-by-step guide for obtaining a custom recovery TWRP and Root to 2016 Samsung Tab A tablets.
Credit to the software authors, original post creators (especially jcadduono and ashxy) and all those who contributed to the discussions to clarify all the issues.
Here is my set of instructions to gain TWRP and Root on the Tab A (WIFI) SM-P580, SM-T580, and SM-P585.
WARNING Flashing a custom recovery to your device will trip the Knox warranty bit on your phone. Check with your mobile provider to see if they will still cover warranty on Knox bit triggered devices. If you understand this risk, continue on. You generally don't have to worry, as it's incredibly hard to brick a Samsung device, and physical damage warranties should be exempt from Knox triggering. [credit: jcadduono]
If you prefer Magisk to chainfire supersu, please see the modification described in https://forum.xda-developers.com/showpost.php?p=73719123&postcount=82
1. DOWNLOAD
a. ODIN https://build.nethunter.com/samsung-tools/Odin_3.12.3.zip
b. Samsung USB Drivers http://developer.samsung.com/technical-doc/view.do?v=T000000117
c. Original firmware
For SM-P580 Search for SM-P580 at http://updato.com/firmware-archive-select-model
For SM-T580, https://www.sammobile.com/firmwares/database/SM-T580/XAR/. (Thanks post #2)
For SM-P585, Search for SM-P585 at http://updato.com/firmware-archive-select-model​ d. TWRP
For SM-P580 https://dl.twrp.me/gtanotexlwifi, click twrp-3.0.2-0-gtanotexlwifi.img.tar, then follow directions to download
For SM-P585 https://dl.twrp.me/gtanotexllte/
For SM-T580 https://dl.twrp.me/gtaxlwifi/​ e. SuperSU (get latest version) https://download.chainfire.eu/supersu
f. ashxy's Dm-verity and force encryption disabler https://www.androidfilehost.com/?fid=24591000424951049​
2. PREPERATION
a. While running your tablet in Android, go to Settings -> About device. Tap 7 times on Build number to enable Developer options. [credit: jcadduono]
b. Now go to Settings -> Developer options. (above About device). You need to enable OEM unlock, otherwise you might end up with boot problems or be unable to flash later on. Do not ever turn off Developer Options or OEM unlock. Doing so will cause your device to refuse to boot and require a full factory restore. [credit: jcadduono]
c. Turn off your tablet.
d. Get a micro SD card
e. Copy SuperSU and dm-verity script onto microSD card
f. Install microSD card into Tablet
g. Install Samsung USB Drivers on Windows machine
h. Unzip ODIN (1a) and Original firmware (1c) on your Windows computer
i. While tablet is off, plug in usb cable between tablet and Windows computer​
3. REFLASH ORIGINAL FIRMWARE (Optional)
a. Enter Download mode, press and hold Home, Down Vol, and Power until you see the Warning screen of the downloader mode. Press Vol up to continue
b. Open up ODIN, confirm that ODIN can see your tablet, click AP button on Odin. In popup, select AP_[blah blah].tar.md5 (whatever AP file you downloaded in step 1c). After selecting the file, Odin will check the signature of the file you downloaded and appear to freeze up. Let it finish, and it will report: <OSM> Checking MD5 finished Sucessfully.. <OSM> Leave CS..
c. Then click Start. The screen of the tablet should show a progress bar as your tablet is being restored to its original firmware.
d. At this point, you need to let the tablet reboot into Android. If ODIN doesn't do this itself, reboot into to download mode (home, vol down, power), then select Vol down to reboot. After a while, you will be greeted with the Welcome screen where you can select your language.
e. Power off the tablet using the power button​
4. FLASH TWRP
a. Enter Download mode (press and hold Home, Down Vol, and Power) until you see the Warning screen of the downloader mode. Press Vol up to continue
b. (Re) Open up ODIN, confirm that ODIN can see your tablet,
c. Important We do not want the tablet to automatically reboot after installing TWRP. If the tablet does reboot into Android before completing the steps in Section 4 and 5, there is a good chance the stock recovery will overwrite TWRP. So click the Options tab on the left and deselect Auto Reboot. After doing that, click the Log tab so you can monitor progress
d. Click AP button on Odin. In popup, select twrp-[blah blah].img.tar (downloaded in step 1d), click Start. You will see the progress bar on your tablet. Watch the log window of Odin and wait for the message "<OSM> All threads completed. (succeed 1 / failed 0)"​
5. ENTER TWRP AND CONFIGURE
a. At this point, from the last section, you should still be in Download mode on the tablet. It is important that, after flashing TWRP, to go straight to TWRP without letting the Android System reboot. To do this, Hold [Volume Down] + [Home] + [Power] to get out of Download mode and immediately swap to [Volume Up] (while still holding [Home] + [Power]) when the screen blanks. [credit: jcadduono]
b. In a few secs, you will see the TWRP first screen, you can let go of all the buttons.
c. If you don't see then TWRP boot splash try again from the start of 4. FLASH TWRP.
d. Swipe to Allow Modifications. (For some reason, TWRP has some issues with the touchscreen for some tablets. If you experience this, expect to make several swipes or taps until it properly registers. You have succeeded when you see the classic 8-button main screen of TWRP. Indeed, throughout your use of TWRP, expect that touches will often not properly register, and just keep trying until it does.)
e. Click Wipe then Format Data (do not just Wipe data), type yes and let it complete. (It is also a good practice, though not always necessary, to Wipe the Cache and Dalvik Cache whenever you make changes to the system. They are always rebuilt as needed. Now is as good a time as any.) Then click back until you get to the 8-button main screen of TWRP.
f. Click the Mount button. Select Storage button, and confirm that the Internal Storage shows non-zero MB. If it is, you know that the /data partition is now mounted properly. However, since we put the needed scripts on the microSD, go ahead and select Micro SD Card as our storage. Click Back until you are back at the 8-button main screen.
g. Click the Install button, install the SuperSU zip file you downloaded in step 1e and copied to your microSD. It will finish and say Updating partition details… …done. Click Back to get back to the install screen (do not reboot yet).
h. Install the no-verity zip file from step 1f. When it completes, you can press the Reboot System button and let your tablet reboot into Android. You can also disconnect the usb cable connecting the tablet from the computer. The tablet may reboot itself once or twice, let it do its thing, and eventually you will see the Samsung Welcome! Screen, where you can select your language.​
6. CONFIRM DATA ACCESS IN TWRP
a. Before going into configuring your tablet, go ahead and turn off the tablet and re-enter TWRP (Home, Vol up, Power).
b. *Important* Since you will not be changing your system partition, this time, when you get to the "Keep System Read only?" screen, click the Keep Read Only button.
c. In the 8-button screen of TWRP, click Mount, click Select Storage. Confirm that the Internal Storage is greater than zero MB. If it is, congratulations, you have TWRP installed with /data mounted. At this point, you might want do a backup. If you want your TWRP backup to be on your microSD card, select it now while still in the Select Storage dialog.
d. Do a backup.
e. Reboot to System​
7. FUTURE USE OF TWRP
a. Unless you are planning to make changes to the System, continue to choose the Read Only System when you return to TWRP. If you need to make changes to System, e.g. flash a new ROM, go back to Step 5 and install the ROM just before Step 5g​
8. Click the Thanks button if my guide helped you.

for T-580 firmware: https://www.sammobile.com/firmwares/database/SM-T580/XAR/

I am on the T580, I can verify that your instructions and links provided are correct.
Great guide! Very organized and straight-forward, thank you for your contribution to the community - I'm sure a lot of people will find this very helpful!

I happened to meet boot-loop.:crying:

openapi said:
I happened to meet boot-loop.:crying:
Click to expand...
Click to collapse
did u fix ur bootloop and eventually get this working?

Thank you! Thank you! Thank you!I have been trying for 2 hours to get into TWRP.. Step 5a made all the difference in the world!!

Great write up
Thank You!!!

having trouble with the SM-T580/XAR link
any alternative links ? and what is the difference between the to files under that link ?

I've read on other threads that Google FRP (factory reset protection) may cause boot loops when rooting if you've not disabled it, but I can't find a definitive answers on exactly how you disable on the Tab A.
Anyone have the answer?
---------- Post added at 01:10 PM ---------- Previous post was at 01:07 PM ----------
HarryKlanderman said:
having trouble with the SM-T580/XAR link
any alternative links ? and what is the difference between the to files under that link ?
Click to expand...
Click to collapse
Make sure you disable any ad blockers in your browser and you sold get to the free (slow) download. Different files are for various regions providing language and keyboard locale settings.

Fantastic write up. Worked flawlessly on a brand new SM-P580.
Only thing to add: After finishing all the steps and the tablet is booted, at first launch of SuperSU, it will ask you to disable Knox. If you say OK, the process will likely will hang. So press OK and let SuperSU try. If it hangs for more than 30 seconds, reboot the tab, go back into SuperSU, select OK when asked again, and it should successfully disable Knox.
Also, I did not re-flash the original firmware (since this was a new tablet).

Any work on SM-T587P being done? Us Sprint users are chomping at the bit, lol.....

Does anyone know if or when Lineage OS (official or unofficial) may come to the T580?

Negative On Sprint
currentuserjade said:
Any work on SM-T587P being done? Us Sprint users are chomping at the bit, lol.....
Click to expand...
Click to collapse
I am unable to get this working on the T587P, Sprint Varient. I can flash the LTE version of it (For the T580) but it will not successfully boot to recovery, instead getting stuck on "Recovery Booting" and then showing an odd modified download menu (oddly, I can still flash things through this broken recovery).

Any workaround to root the device without modifying the Knox counter ? It's very hard to choose between voiding the warranty or standing with the ads!

the gladiator said:
Any workaround to root the device without modifying the Knox counter ? It's very hard to choose between voiding the warranty or standing with the ads!
Click to expand...
Click to collapse
In short, no. Any custom recovery will trip the Knox counter, and as this is required to obtain root, you can't get root without tripping the counter.

DingoBat said:
In short, no. Any custom recovery will trip the Knox counter, and as this is required to obtain root, you can't get root without tripping the counter.
Click to expand...
Click to collapse
I agree with Dingo. As mentioned in the Warning on the first post, because of Odin, it is pretty hard to brick these devices; you can always flash a stock image (assuming you have one for your exact make and model) to bring your device back from the grave. If you think it is likely that you will seek support from your phone company, ask them if they can provide support to phones with knox tripped. If instead, you seek your support from XDA, then a tripped Knox is kinda the ritual of initiation. Welcome to the club!

I can get to point 5f.
f. Click the Mount button. Select Storage button, and confirm that the Internal Storage shows non-zero MB. If it is, you know that the /data partition is now mounted properly. However, since we put the needed scripts on the microSD, go ahead and select Micro SD Card as our storage. Click Back until you are back at the 8-button main screen.
Click to expand...
Click to collapse
However, I can't mount the SD card. Clicking on it doesn't do anything. Any suggestions? I checked if the card could be read before installing TWRP and the SU-file was there.

bartveld said:
I can get to point 5f.
However, I can't mount the SD card. Clicking on it doesn't do anything. Any suggestions? I checked if the card could be read before installing TWRP and the SU-file was there.
Click to expand...
Click to collapse
Are you able to boot into Android, and if so, are you able to see the contents of the SD card using the file browser?

klaberte said:
Are you able to boot into Android, and if so, are you able to see the contents of the SD card using the file browser?
Click to expand...
Click to collapse
Yes, it's all accessible through Android. But of course, once I start up Android after step 5f I lose TWRP and have to start over again.

Yippee! All I had to do was format the sd card and now everything works fine! Thanks for the help and a great guide.

[GUIDE][Z2 FORCE XT1789-05] Bootloader/TWRP/Custom ROMs/Root/Dirty flashing/Unbrick

First, thanks to @Uzephi and @41rw4lk for helping me to use/recover my phone. Please, read and do not underestimate the guides: our phone is tricky! We have two system partitions (slot a and b) to allow stock updates on-the-fly. This complicates the normal flashing process and if you do not follow the steps, you may bootloop. Use these guides at your own risk!
Reading this page is a good beginning to understanding the A/B partitioning scheme and how Motorola Z2 Force works:
1) Our phone has A/B partitioning, so flashing Magisk/XPosed is different
2) It does not support Project Treble (faster stock updates)
3) It does not a recovery partition, so flashing TWRP is different
Note also that the RSD Lite from Motorola has issues with Windows 10 and you’ll need to manual flash firmware if you bootloop (see Process E below). Other way is directly flashing from Qualcomm EDL mode (Emergency Download Mode) from which users can perform various tasks like unbricking, unlock bootloader, and installation of any custom ROMs.
Right now, this guide has 5 parts (maybe we can dual boot our phone in the future). If you just want to use a rooted stock ROM, please, search for other guides here on xda. These guides were written (and tested) using a Motorola Z2 Force XT1789-05 phone (Brazil), although most of it should work for other variants if you download and use proper firmware files for these other phones. For other models, better if you follow Uzephi’s guide.
A. Opening bootloader
B. Preparing the phone to move into custom ROMs (AOSP) + TWRP recovery
C. Flashing a custom AOSP ROM + rooting
D. Dirty flashing AOSP ROM updates
E. Recovering from bricks or returning to stock
F. Oreo ROM features comparison table
If you want to move your Motorola Z2 Force to Project Treble ROMs, please, check this guide.
Here is a list of the ROMs that are waiting for you.

A. Opening bootloader
With enough battery in your phone (80%), you can follow the Motorola official guide which steps are:
1. Backup everything you need. Your phone will be reseted including the internal sdcard.
2. Into the phone, enable the Developer Options clicking 7 times over the version (About section in the Settings). Go to Developer Options, click the OEM unlock option to enable it. Also enable USB debugging.
3. Install the Motorola drivers in your computer, but (in my personal experience) not the Android SDK suggested in the official guide. Instead, extract these adb/fastboot files in a blank folder of your computer.
3.1) Do not use other adb/fastboot binaries: I cannot guarantee they will work.
3.2) You need to use a USB 2.0 port of your computer. Some users report that USB 3.0 will also work.
4. Open a command line window in the adb/fastboot folder (step 3), reboot the phone into the bootloader (see adb command below or press power + volume down buttons). Plug the phone on computer (see 3.2 above). Test the connection and run the command to get the code for unlocking:
Code:
adb reboot bootloader
fastboot devices
fastboot oem get_unlock_data
You’ll get:
Code:
(bootloader) Unlock data:
(bootloader) <code 1>
(bootloader) <code 2>
(bootloader) <code 3>
(bootloader) <code 4>
(bootloader) <code 5>
5. You’ll need to join 5 codes and, after logging into your own Motorola account, check by clicking the button “Can my device be unlocked” (step 6) by Motorola here. Read the text: your warranty will be void if you go ahead. Consider if you have enough knowledge, time and money to deal with a troublesome (or bricked) device. Although, it’s not that easy to hard brick this phone (see process E below).
Code:
<code 1><code 2><code 3><code 4><code 5>
6. You’ll receive back an email with the code to unlock your bootloader (if it is available for your model). Then you’ll run the following command:
Code:
fastboot oem unlock <code 1><code 2><code 3><code 4><code 5>
7. You’ll receive a warning that all your data would be erased (see step 1 above) and need to re-run the same command to confirm. At this point, your bootloader should be unlocked. As an Android restriction, each time you boot the phone you’ll see a warning. Do nothing, wait for 5 seconds and the phone boots normally. Some users bother with this warning and try to get rid of it.

B. Preparing the phone to move into custom ROMs (AOSP) + TWRP recovery
Requirements: unlocked bootloader (see guide A) and no security lock: disable PIN, gestures and fingerprinting (because TWRP cannot read the locked/cryptographed data of the phone). Enough battery in your phone (80%).
If you do not prepare your phone to custom ROMs and if you do not have both bootloaders of the phone in the same Android version of the ROM you’ll flash, you’ll hard brick the phone and lose also the access to the bootloader! You’ve been warned: follow the guide!
Note: if you hard brick, I suggest you be prepared to follow the Unbrick Qualcomm mobiles with Step-by-step guide or the Unbrick All Qualcomm Snapdragon’s from Qualcomm HS-USB QDLoader 9008 guide, but I never tested them myself. You can also use Qualcomm Flash Image Loader (QFIL) tool.
1. Backup everything you need. Your phone will be reset including the internal sdcard.
2. Into the phone, enable the Developer Options clicking 7 times over the version (About section in the Settings). Go to Developer Options and enable USB debugging.
3. Install the Motorola drivers and the adb/fastboot files.
3.1) do not use other adb/fastboot binaries: we cannot guarantee they will work.
3.2) you need to use a USB 2.0 port of your computer. Some users report that USB 3.0 will also work.
4. Download the firmware of the same Android major version of the future ROM you’ll install (Oreo for Oreo ROMs, for instance). When (and if) we move to Android P, most probably we will need to follow this guide again.
- Retail (XT1789-05) (Europe/Brazil).
- Other models (branded): ATT, Sprint, T-Mobile (TMO), USC, Verizon.
- Note: NPXS26 versions stand for Nougat and OPXS27 for Oreo. You do not need Nougat versions for anything.
5. Extract the zip contents to a blank folder in your computer.
6. Download the FlashAll_XT1789-05.zip file, extract the content and move all files to the same firmware folder (step 5 above). Be sure to overwrite any file (if needed).
7. Run the Preparation.bat file there to generate the flashfile.bat file that will send the commands to the phone. Credits: the original preparation files were from RootJunky (can be downloaded here) and include more options that we do not need for our purpose here. Also, it includes adb/fastboot binaries that could not work with our phone.
8. Reboot the phone into the bootloader (see adb command below or power + volume down buttons). Open a command line window in the firmware folder (step 5 above), test the connection and execute the flashfile.bat file generated on step 7.
Code:
adb devices
adb reboot bootloader
fastboot devices
flashfile.bat
Never ever unplug the device from the USB 2.0 port while flashing the firmware. This could cause a hard brick and your device will be dead.
9. There is a pause at the end. You should review if everything went fine (or even click on the menu of the command line window, select all and copy&paste the contents in a .txt file for further help/revision).
10. Reboot your phone into the system (ROM) and do a quick configuration (remember that everything will be deleted when you install TWRP further…).
11. Into the phone, enable the Developer Options clicking 7 times over the version (About section in the settings). Go to Developer Options and enable USB debugging.
12. Download both the .img and .zip file of the TWRP recovery from the official site. It's the same file for all models/variants of Z2 Force phone. Put the files into our firmware folder (step 5 above). Copy the .zip file to the phone internal card. Note: versions older than 3.2.2-2 does not support PIN/Password/Fingerprint, so disable them before proceed. Most probably, ROMs before July 20th, 2018 cannot be flashed in older TWRP.
13. Now boot (not flash) the TWRP .img file using a command line window in the same firmware folder (step 5 above):
Code:
adb devices
adb reboot bootloader
fastboot devices
fastboot boot <TWRP file name>.img
14. Only now that you’re inside TWRP temporarily flash the TWRP .zip file you’ve saved into the phone (step 12 above).
15. Reboot into TWRP (use the main reboot menu in TWRP).
16. Now, you should reboot again into bootloader: inside TWRP, go to Reboot menu and choose Bootloader.
17. Now you will wipe all user data via bootloader. This is necessary to use an AOSP ROM when you come from stock. Using a command line window in the same firmware folder of your computer (step 5 above), run the following commands:
Code:
fastboot devices
fastboot -w
18. Now you can reboot the phone into System using the buttons volume up/down to navigate and confirming with the Power button. You’ll be with stock ROM and TWRP. If you want to move to a custom AOSP ROM, do a quick configuration: into the phone, enable the Developer Options clicking 7 times over the version (About section in the settings). Go to Developer Options and enable USB debugging and go to the proper guide (Process C).

C. Flashing a custom AOSP ROM + rooting
1. Requirements:
1.1 Motorola drivers.
1.2 Our custom adb/fastboot files (others may not work!).
1.3 USB debugging enabled into the Developer Options.
1.4 If you're using TWRP older than 3.2.2-2, disable disable PIN/gestures/fingerprinting. Also, most probably, ROMs after July 20th, 2018 cannot be flashed in older TWRP.
1.5 An USB 2.0 port of your computer (some users report that USB 3.0 will also work).
1.6 Two Oreo bootloaders (process B above).
1.7 Permanent TWRP
1.8 Enough battery in your phone (80%).
2. Download the AOSP ROM you want and move the .zip files to the phone. Right now, we have:
2.1 Dirty Unicorns: no need for Gapps. Official and Weeklies can be dirty flashed interchangeably. RC has a different signature. Support on Google+ page. More about DU kernel.
2.2 Lineage OS 15.1. MindTheGapps needed. OpenGapps not compatible yet. XDA thread.
2.3 Mokee: Gapps needed. Take care: online guides assume that you already have an AOSP ROM, TWRP and rooted device.
Deprecated (?)
2.4 AOSiP: no need for Gapps. XDA thread.
2.5 Invictrix. Gapps are built in. XDA thread
3. Choose the root method and download the .zip files: Magisk (suggested) or LineageOS SU Addon. Move the .zip files to phone. Note: if you bootloop on Magisk, most probably you’re flashing a wrong/different version of Magisk or you did not reboot between flashing ROM/Gapps and Magisk. Note: SuperSu is deprecated.
4. Reboot into TWRP:
Code:
adb reboot recovery
Then flash the ROM. It will be flashed in two steps only in the “other” slot. We have two slots, A and B. Our phone can be upgraded on-the-fly because the update is always applied to the slot not booted, the “other” slot. Then, immediately, flash the .zip TWRP or you will lose it.
5. Go to Reboot menu of TWRP and reboot into bootloader. Then, in the folder with adb/fastboot binaries (see 1.2 above), you need to wipe data (including sdcard) with the following commands:
Code:
fastboot devices
fastboot -w
6. Now you need to reboot the phone into System using the buttons volume up/down and confirming with the Power button (or typing fastboot reboot into the command line windows). You’ll be with an AOSP ROM and TWRP.
7. Once into the phone, enable the Developer Options clicking 7 times over the version (About section in the settings). Go to Developer Options and enable USB debugging if you intend to dirty flash ROM updates.
8. Reboot into TWRP again, flash Magisk (your settings and modules will be preserved). Note: if you bootloop on Magisk, remember it is mandatory to reboot between ROM flash (step 4 above) and GApps/Addon flash due to verity/slot-swap logic.
9. A good place to read what is not working is in the section known problems of LineageOS.

D. Dirty flashing AOSP ROM updates
1. If you follow all the processes above, you can dirty flash updates because you have:
1.1 Motorola drivers installed.
1.2 Specific adb/fastboot files for our phone and an USB 2.0 port in a Windows computer (some users report that USB 3.0 will also work).
1.3 Unlocked bootloaders (Process A above).
1.4 Permanent TWRP running and TWRP .zip file placed inside your phone and ready to be flashed again.
1.5 An AOSP ROM already running.
1.6 Developer Options and USB debugging enabled.
1.7 If you're using TWRP older than 3.2.2-2, disable disable PIN/gestures/fingerprinting. Also, most probably, ROMs after July 20th, 2018 cannot be flashed in older TWRP.
1.8 Enough battery in your phone (80%)
2. Download your ROM .zip update, copy it into the phone sdcard and reboot your phone into TWRP. See download links here.
3. Within TWRP you should flash (install) things in the following order:
3.1 ROM update .zip file. Remember that, at this time, the update will be flashed int the other slot and inside phone you’ll have both the system before update (in the booted slot) and updated ROM in the other slot.
3.2 TWRP .zip file (step 1.4 above) once again (do not skip this step or you’ll bootloop!).
4. Reboot to System: if you skip this step, you’ll bootloop.
5. Reboot into TWRP again, flash Magisk (your settings and modules will be preserved) or LineageOS SU Addon .zip file. Note: if you bootloop on Magisk, most probably you’re flashing a wrong/different version of Magisk. I suggest v16.0 and, after you got rooted with 16.0, you can update. It is mandatory to reboot between ROM flash (step 4 above) and GApps/Addon flash due to verity/slot-swap logic.
Note: SuperSu is deprecated.
6. Wipe Dalvik/ART cache: go to Wipe menu of TWRP > Advanced Wipe > Dalvik/ART Cache only.
7. Reboot your phone into System (ROM) will use the “other” slot, the one with the updated ROM.
8. You can use XPosed installer app (and reboot).
9. Now you can add your PIN, fingerprint, gestures back until next flashing.

E. Recovering from soft bricks or returning to Stock
If you’re reading this is because you already unlock your bootloader (see guide A) and anything went wrong, but you still can boot your phone into bootloader. Plug your phone and get enough battery (even if you do not see any charging signal).
1. Install the Motorola drivers and the specific adb/fastboot files for our phone. Remember, follow the rules because our device is tricky!
1.1) Do not use other adb/fastboot binaries: we cannot guarantee they will work.
1.2) You need to use a USB 2.0 port of your computer (some users report that USB 3.0 will also work).
2. Download the latest firmware for your model:
- Retail (XT1789-05) (Europe/Brazil).
- Other models (branded): ATT, Sprint, T-Mobile (TMO), USC, Verizon.
- Note: NPXS26 versions stand for Nougat and OPXS27 for Oreo. You do not need Nougat versions for anything.
3. Extract the zip contents to a blank folder in your computer.
4. Download the FlashAll_XT1789-05.zip file (it should work for other Motorola Z2 Force models as well), extract the content and move all files to the same firmware folder (step 2 above). Be sure to overwrite any file (if needed).
5. Run the Preparation.bat file there to generate the flashfile.bat file that will send the commands to the phone. Credits: the original preparation files were from RootJunky (can be downloaded here) and include more options that we do not need for our purpose here. Also, it includes adb/fastboot binaries that could not work with our phone.
6. Reboot the phone into the bootloader (see adb command below or power + volume down). Open a command line window in the firmware folder (step 5 above), test the connection and execute the flashfile.bat file generated on step 5.
Code:
adb reboot bootloader
fastboot devices
flashfile.bat
Never ever unplug the device from the USB 2.0 port while flashing the firmware. This could cause a hard brick and your device will be dead.
7. There is a pause at the end. You should review if everything went fine (or even click on the menu of the command line window, select all and copy&paste the contents in a .txt file for further help/revision).
8. Reboot your phone into system (ROM) and do not forget, later, to enable the Developer Options and USB debugging again.
Note: if you hard brick, I suggest you be prepared to follow the Unbrick Qualcomm mobiles with Step-by-step guide or the Unbrick All Qualcomm Snapdragon’s from Qualcomm HS-USB QDLoader 9008 guide, but I never tested them myself. You can also use Qualcomm Flash Image Loader (QFIL) tool. Maybe these Latest 2017 Qualcomm Diag QD-Loader Windows 10 Drivers signed will help you.

F. Oreo ROM features comparison
This is a table for Oreo ROM features comparison for Motorola Z2 Force - nash.
I would like to receive feedback and updates from the users, as I can't keep changing from one ROM to another and they get new features, updates, improvements, etc.
I consider Lineage OS 15.1 our stock ROM regarding to customization. So, it's not listed there.
Legend:
Code:
X = Feature present
XX = ROM excels in this particular feature (in my opinion).

If you want to move your Motorola Z2 Force to Project Treble ROMs, please, check this guide.
Here is a list of the ROMs that are waiting for you.

I came back to stock ROM. the problem is that it gets stuck in the initial configurations of the android trying to find a wifi network, to continue the configuration, without success, because I see in fastboot that the baseband is unknown, and I also can not install any rom, or recovery image because I have the following message in fastboot: FLASHING_LOCKED. and since I can not get past the initial android settings, I also can not unlock the developer options to enable OEM unlocking. now I'm standing in a rom that does not leave the initial configuration, it does not connect to any network and a fastboot that does not let me install anything. and I also tried the recovery mode and even tried to install an update via sideload, without success. I do not know what else to do if you can give me a light.

renanjones said:
I came back to stock ROM. the problem is that it gets stuck in the initial configurations of the android trying to find a wifi network, to continue the configuration, without success, because I see in fastboot that the baseband is unknown, and I also can not install any rom, or recovery image because I have the following message in fastboot: FLASHING_LOCKED. and since I can not get past the initial android settings, I also can not unlock the developer options to enable OEM unlocking. now I'm standing in a rom that does not leave the initial configuration, it does not connect to any network and a fastboot that does not let me install anything. and I also tried the recovery mode and even tried to install an update via sideload, without success. I do not know what else to do if you can give me a light.
Click to expand...
Click to collapse
I see two possible scenarios:
1. Your bootloader is locked (yet) (see guide A).
2. Your in a "false locked" situation that, maybe, could be solved by resetting data via recovery or in bootloader (with the command: fastboot -w).

Great tutorial, but I did not get 4g in any of the roms, only 3g

Gutto said:
Great tutorial, but I did not get 4g in any of the roms, only 3g
Click to expand...
Click to collapse
I got 4G in any ROM... AOSIP, DU or Invictrix...
Are you using a branded (carrier) phone? If not, maybe you should return to stock (to recover any changes on partitions).

Technical said:
I got 4G in any ROM... AOSIP, DU or Invictrix...
Are you using a branded (carrier) phone? If not, maybe you should return to stock (to recover any changes on partitions).
Click to expand...
Click to collapse
My cell phone and Sprint, I did every process that you indicated, but not 4G

So I followed the instructions as noted, as soon as I got to the root installation part, it started throwing a "cannot mount /system" error. I thought a reboot would solve the issue, but now I think I'm bricked. Can't boot into anything, all I can do is plug my phone in and listen to it keep disconnecting every 10 seconds or so. The phone had booted up fine prior to starting the installation process, and I don't see how just a bad ROM install is preventing me from getting into either bootloader or recovery. Any advice?
For clarity, i'm unable to use QBOOT to do anything since after it hits the "powered on" state I'm assuming it's in, it just resets and does the same thing over and over again

shalpp said:
So I followed the instructions as noted, as soon as I got to the root installation part, it started throwing a "cannot mount /system" error. I thought a reboot would solve the issue, but now I think I'm bricked. Can't boot into anything, all I can do is plug my phone in and listen to it keep disconnecting every 10 seconds or so. The phone had booted up fine prior to starting the installation process, and I don't see how just a bad ROM install is preventing me from getting into either bootloader or recovery. Any advice?
For clarity, i'm unable to use QBOOT to do anything since after it hits the "powered on" state I'm assuming it's in, it just resets and does the same thing over and over again
Click to expand...
Click to collapse
Have you tried holding vol dwn + pwr btn to force it into bootloader mode? If you can get there, then you can use the keys to get to recovery and try a factory reset. If that don't work, go back to bootloader mode and try flashing back to stock. Might double check that the battery has plenty of charge.

41rw4lk said:
Have you tried holding vol dwn + pwr btn to force it into bootloader mode? If you can get there, then you can use the keys to get to recovery and try a factory reset. If that don't work, go back to bootloader mode and try flashing back to stock. Might double check that the battery has plenty of charge.
Click to expand...
Click to collapse
I'm unable to get the phone out of qboot (or whatever it's called). I've tried using a blank-flash but all that happens is device restarts as made evident by the "device disconnect" sound playing every few seconds. The phone had around 80% when I started the process. Should I just let it die and try loading into BL after a few hours of this thing power cycling itself?

shalpp said:
I'm unable to get the phone out of qboot (or whatever it's called). I've tried using a blank-flash but all that happens is device restarts as made evident by the "device disconnect" sound playing every few seconds. The phone had around 80% when I started the process. Should I just let it die and try loading into BL after a few hours of this thing power cycling itself?
Click to expand...
Click to collapse
It's weird that it is power cycling like that. Have you tired unplugging the phone and booting? Whether it's recovery, bootloader, qboot; you need to get to one place or the other if possible because power cycling won't allow you to do anything. If you can get a stable boot in any mode I would suggest moving your cable to another port so any corruptions aren't a factor anymore. I don't think a drain will resolve anything, but I've never heard anyone mention power cycling like that.

41rw4lk said:
It's weird that it is power cycling like that. Have you tired unplugging the phone and booting? Whether it's recovery, bootloader, qboot; you need to get to one place or the other if possible because power cycling won't allow you to do anything. If you can get a stable boot in any mode I would suggest moving your cable to another port so any corruptions aren't a factor anymore. I don't think a drain will resolve anything, but I've never heard anyone mention power cycling like that.
Click to expand...
Click to collapse
Power cycling is just an assumption since regardless of whatever port its in it keeps an endless loop of connect, disconnect". Basically after rebooting the device after attempting to install the ROM is when it went black and started not doing anything other than connect, disconnect

shalpp said:
Power cycling is just an assumption since regardless of whatever port its in it keeps an endless loop of connect, disconnect". Basically after rebooting the device after attempting to install the ROM is when it went black and started not doing anything other than connect, disconnect
Click to expand...
Click to collapse
When it's trying to connect do you have a pop up on your pc showing what it sees the phone as? Does it say nash fastboot, or 9008, Z2? That might give some idea of where it's failing.

41rw4lk said:
When it's trying to connect do you have a pop up on your pc showing what it sees the phone as? Does it say nash fastboot, or 9008, Z2? That might give some idea of where it's failing.
Click to expand...
Click to collapse
It appears as Qualcomm 9008
It only starts the loop after starting a blankflash. That's about the only response I get out of the device, otherwise it does absolutely nothing, no combination of buttons do anything
Edit: Confirmed connect/disconnect on another machine with the same driver configuration