Related
Ok guys, this is a sureshot guide for
PROBLEM
* anyone wanting to decrypt their op3 but stuck at 1+ boot screen(Or not able to boot any custom ROMs.) and only able to restore twrp backups
* After using fastboot format userdata twrp and about phone shows only 32gb phone memory(where the hell is my rest of 32gb )
* Fastboot format userdata resulting in Stuck at boot screen or simply an unbrick trick to return to Stock OOS in unencrypted stage
SOLUTION
1. Use method 2 of Mega unbrick guide to restore your phone to stock partitions found here
http://forum.xda-developers.com/oneplus-3/how-to/guide-mega-unbrick-guide-hard-bricked-t3405700
2. After the flashing is complete do not reboot the phone instead reboot directly into bootloader.
3. In fastboot mode flash modded twrp 3.0.2.22 using command ''fastboot flash recovery recovery.img'' found here
http://forum.xda-developers.com/devdb/project/?id=15934#downloads
4. Reboot directly into twrp and using mtp mode copy latest elemental x kernel or bluspark kernel zip for OOS and SYSTEM supersu.zip into the internal storage. System supersu.zip here OR directly proceed to step 8
https://s3-us-west-2.amazonaws.com/supersu/download/zip/SuperSU-v2.78-201609011115.zip
5. Now flash system supersu.zip and directly after that kernel.zip
6. Now again reboot to recovery directly and from twrp boot into system.
7. After boot up you system should be decrypted. You can check in security settings.
8.Reboot recovery and flash required firmware + modem zip found here
http://forum.xda-developers.com/oneplus-3/how-to/radio-modem-collection-flashable-zips-t3468628
9.wipe data +cache +dalvik +system
10. Flash any rom of your choice and go flashoholic, use multirom or whatever you want.
Pheww. Thanks.
Man, Finally the SystemRoot (V4A, MultiROM etc) as we discussed a couple of weeks back with this hassle at the Mega Unbrick and Decrypt guides threads...:highfive:
I saw your post on MultiROM but maybe it got moved I guess...
So are you able to cross flash anything now ?
thanks.
Ashtrix said:
Man, Finally the SystemRoot (V4A, MultiROM etc) as we discussed a couple of weeks back with this hassle at the Mega Unbrick and Decrypt guides threads...:highfive:
I saw your post on MultiROM but maybe it got moved I guess...
So are you able to cross flash anything now ?
thanks.
Click to expand...
Click to collapse
anything... even multirom works flawless.
I will give this a try, Or will try to Flash the EX then perform parts of this since they support Kexec, to see what works, I have data and lot of apps working them again is a real pita with my schedule...
Thanks but, this is basically what i have done to decrypt my op3, i just used the CypherOs ROM instead OxygenOs, fastboot format userdata, reboot to recovery, flash rom, flash elementalx, and i didnt flash Supersu(dont know if thats causing my problem, i dont think so), i also did fastboot format userdata without being stuck at boot logo and still no 32gb, dont know whats the problem
ach3fck said:
Thanks but, this is basically what i have done to decrypt my op3, i just used the CypherOs ROM instead OxygenOs, fastboot format userdata, reboot to recovery, flash rom, flash elementalx, and i didnt flash Supersu(dont know if thats causing my problem, i dont think so), i also did fastboot format userdata without being stuck at boot logo and still no 32gb, dont know whats the problem
Click to expand...
Click to collapse
its different fastboot format userdata causes this Dont know why. I suggest method in the OP. Read carefully and follow it.
nikhilsnigam said:
its different fastboot format userdata causes this Dont know why. I suggest method in the OP. Read carefully and follow it.
Click to expand...
Click to collapse
Aham, so the format userdata causes it, thanks for that. i want to ask you something, after restoring completely with Msmdownloadtool(method2) can i directly reboot to recovery then sideload CB 3.5.5 and then reboot to fastboot and continue with the tutorial? What im saying is my device is decrypted as long it doesnt boot, am i right?
ach3fck said:
Aham, so the format userdata causes it, thanks for that. i want to ask you something, after restoring completely with Msmdownloadtool(method2) can i directly reboot to recovery then sideload CB 3.5.5 and then reboot to fastboot and continue with the tutorial? What im saying is my device is decrypted as long it doesnt boot, am i right?
Click to expand...
Click to collapse
Yes you can but you will be encrypted again. so after msm method reboot fastboot and flash modded twrp. reboot recovery flash CB or OOS. flash supersu flash kernel. Agin flash twrp.img from recovery itself and reboot recovery. After that reboot system and you are good to go. Make sure you have enough system space before flashing supersu and kernel. frow twrp file manager delete unneeded system apps 1st. DO NOT REBOOT in between.
nikhilsnigam said:
Yes you can but you will be encrypted again. so after msm method reboot fastboot and flash modded twrp. reboot recovery flash CB or OOS. flash supersu flash kernel. Agin flash twrp.img from recovery itself and reboot recovery. After that reboot system and you are good to go. Make sure you have enough system space before flashing supersu and kernel. frow twrp file manager delete unneeded system apps 1st. DO NOT REBOOT in between.
Click to expand...
Click to collapse
But i need unlocked bootloader to flash twrp, so i guess i need to unlock after i use Msmdownload tool right?
ach3fck said:
But i need unlocked bootloader to flash twrp, so i guess i need to unlock after i use Msmdownload tool right?
Click to expand...
Click to collapse
your bootloader doesn't get locked
nikhilsnigam said:
your bootloader doesn't get locked
Click to expand...
Click to collapse
Sorry to bother you, but i have one more question, i used Msmdownloadtool before, but only in Qualcomm download mode, can i use fastboot or i have to boot to EDL(qualcomm download mode)? And again sorry for taking your time.
ach3fck said:
Sorry to bother you, but i have one more question, i used Msmdownloadtool before, but only in Qualcomm download mode, can i use fastboot or i have to boot to EDL(qualcomm download mode)? And again sorry for taking your time.
Click to expand...
Click to collapse
you have to use qualcomm download mode by switching off your phone. pressing vol up button and connecting to usb.
nikhilsnigam said:
you have to use qualcomm download mode by switching off your phone. pressing vol up button and connecting to usb.
Click to expand...
Click to collapse
Yeah, i know that, thanks a lot, will try later all of this since i have no time now, will report how it went.Thanks!
Hello! Hoping someone can help and guide me in fixing my A2's bootloop. I already searched many forums online, but still no luck.
I flashed a permissiver_v5.zip in Evolution X Rom hoping that it will solve the random reboots, and I got bootloop. I successfully flashed the July stock rom through Miflash, hoping to boot into system, but still bootloop. I flashed the stock firmware and persist zip too in TWRP, but I also got mount persist error. I also need to use fastboot boot twrp.img to get into Twrp since it will disappear after clicking reboot recovery. I tried EDL, but then I got not enough storage error in Miflash.
Hopefully somebody can help me with steps!
LATEST UPDATE:
With the help of KevMetal, I can now use my phone after a week of being hardbricked. At first, my device can't boot to the bootloader or recovery, so what I did was to press the volume down and power button for some time and my phone was detected by the PC. So my device booted to EDL by itself, no need to open the phone. Then I used the 2018 version of MiFlash Tool and flashed the V.10.0.17 of stock Pie ROM from here: https://forum.xda-developers.com/mi-...-t3824849/amp/
After that, I flashed the persist.zip provided by KevMetal (browse in this thread) in recovery since I can't sideload the zip, and it worked fine. I then booted to system and finally there was no bootloop.
I then noticed that the IMEI was gone, so I tried to fix through some guides online but this one worked for me. https://medium.com/@shekhawatkoki/fi...1-2ed533548d32
Ronaldendoma said:
Hello! Hoping someone can help and guide me in fixing my A2's bootloop. I already searched many forums online, but still no luck.
I flashed a permissiver_v5.zip in Evolution X Rom hoping that it will solve the random reboots, and I got bootloop. I successfully flashed the July stock rom through Miflash, hoping to boot into system, but still bootloop. I flashed the stock firmware and persist zip too in TWRP, but I also got mount persist error. I also need to use fastboot boot twrp.img to get into Twrp since it will disappear after clicking reboot recovery. I tried EDL, but then I got not enough storage error in Miflash.
Hopefully somebody can help me with steps!
Click to expand...
Click to collapse
you are messing up ..stop ..
1.boot into fastboot
2. flash stock rom with miflash
3. boot back to fastboot
4. download orange fox or pitch black recovery that actually supports persist flashing
5. join global mi a2 telegram group download relevant persist like if mi a2 or mi x6 and on android 9 or 10
6. put it in adb folder
7. boot recovery ( don't flash)
8. in recovery activate sideload adb option
9. in command window run :adb sideload persist.zip ( persist must have this name in adb folder )
10. now reboot your phone
*in the beginning it will bootloop four or five times ..just leave it
***suddenly your phone will be back to new
***stop flashing permissver and other crap
Sent from my wayne using XDA Labs
KevMetal said:
you are messing up ..stop ..
1.boot into fastboot
2. flash stock rom with miflash
3. boot back to fastboot
4. download orange fox or pitch black recovery that actually supports persist flashing
5. join global mi a2 telegram group download relevant persist like if mi a2 or mi x6 and on android 9 or 10
6. put it in adb folder
7. boot recovery ( don't flash)
8. in recovery activate sideload adb option
9. in command window run :adb sideload persist.zip ( persist must have this name in adb folder )
10. now reboot your phone
*in the beginning it will bootloop four or five times ..just leave it
***suddenly your phone will be back to new
***stop flashing permissver and other crap
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
Thank you so much for your reply. I really appreciate it. I admit that I am really wrong in flashing that permissiver zip. I just hoped that it will solve my random reboot issue, from this tutorial: https://www.google.com/url?sa=t&sou...BMAB6BAgCEAE&usg=AOvVaw2suOu9rYeTps71AvKuZbrA
So now, I already downloaded OrangeFox-R10.1_1-Stable-jasmine_sprout.zip for recovery and persist_restorer_6x.zip from the Telegram group, which is universal persist according to them.
But I just have some questions:
1. Do I need to wipe both a and b in recovery or use command fastboot -w before flashing the stock ROM?
2. After flashing stocK ROM in Miflash tool, it will start to boot to system, but in this case, bootloop, so am I right to press buttons to forcibly go to bootloader?
3. For #7 (boot to recovery), this means fastboot boot recovery.img?
4. For #9, if adb sideload doesn't work, can I flash persist in recovery instead?
Ronaldendoma said:
Thank you so much for your reply. I really appreciate it. I admit that I am really wrong in flashing that permissiver zip. I just hoped that it will solve my random reboot issue, from this tutorial: https://www.google.com/url?sa=t&sou...BMAB6BAgCEAE&usg=AOvVaw2suOu9rYeTps71AvKuZbrA
So now, I already downloaded OrangeFox-R10.1_1-Stable-jasmine_sprout.zip for recovery and persist_restorer_6x.zip from the Telegram group, which is universal persist according to them.
But I just have some questions:
1. Do I need to wipe both a and b in recovery or use command fastboot -w before flashing the stock ROM?
2. After flashing stocK ROM in Miflash tool, it will start to boot to system, but in this case, bootloop, so am I right to press buttons to forcibly go to bootloader?
3. For #7 (boot to recovery), this means fastboot boot recovery.img?
4. For #9, if adb sideload doesn't work, can I flash persist in recovery instead?
Click to expand...
Click to collapse
no install stock using miflash but don't wipe anything ..for this to work well don't install the recovery ..just boot
fastboot boot recovery.img
then using the adb sideload option you can flash the zip from your computer without decryting the internal storage
you can flash magisk the same way ..then you will have stock rooted with persist restored but without custom recovery and your device will remain encrypted ..
if you want custom recovery and install custom rom you can wipe and install but for stock don't do it ..flash persist and magisk from adb sideload without decrypting
2.yeah enter bootloader / fastboot with power button and volume button
4. it will work if done correctly ...if you want to flash from internal storage you will have to wipe and format data to decrypt internal syorage
Sent from my wayne using XDA Labs
KevMetal said:
you are messing up ..stop ..
1.boot into fastboot
2. flash stock rom with miflash
3. boot back to fastboot
4. download orange fox or pitch black recovery that actually supports persist flashing
5. join global mi a2 telegram group download relevant persist like if mi a2 or mi x6 and on android 9 or 10
6. put it in adb folder
7. boot recovery ( don't flash)
8. in recovery activate sideload adb option
9. in command window run :adb sideload persist.zip ( persist must have this name in adb folder )
10. now reboot your phone
*in the beginning it will bootloop four or five times ..just leave it
***suddenly your phone will be back to new
***stop flashing permissver and other crap
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
KevMetal said:
no install stock using miflash but don't wipe anything ..for this to work well don't install the recovery ..just boot
fastboot boot recovery.img
then using the adb sideload option you can flash the zip from your computer without decryting the internal storage
you can flash magisk the same way ..then you will have stock rooted with persist restored but without custom recovery and your device will remain encrypted ..
if you want custom recovery and install custom rom you can wipe and install but for stock don't do it ..flash persist and magisk from adb sideload without decrypting
2.yeah enter bootloader / fastboot with power button and volume button
4. it will work if done correctly ...if you want to flash from internal storage you will have to wipe and format data to decrypt internal syorage
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
Thank you again.
I tried adb sideload before but was stuck at 0%, I missed something. I'll update here for the result once I can be back to PC.
KevMetal said:
you are messing up ..stop ..
1.boot into fastboot
2. flash stock rom with miflash
3. boot back to fastboot
4. download orange fox or pitch black recovery that actually supports persist flashing
5. join global mi a2 telegram group download relevant persist like if mi a2 or mi x6 and on android 9 or 10
6. put it in adb folder
7. boot recovery ( don't flash)
8. in recovery activate sideload adb option
9. in command window run :adb sideload persist.zip ( persist must have this name in adb folder )
10. now reboot your phone
*in the beginning it will bootloop four or five times ..just leave it
***suddenly your phone will be back to new
***stop flashing permissver and other crap
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
KevMetal said:
no install stock using miflash but don't wipe anything ..for this to work well don't install the recovery ..just boot
fastboot boot recovery.img
then using the adb sideload option you can flash the zip from your computer without decryting the internal storage
you can flash magisk the same way ..then you will have stock rooted with persist restored but without custom recovery and your device will remain encrypted ..
if you want custom recovery and install custom rom you can wipe and install but for stock don't do it ..flash persist and magisk from adb sideload without decrypting
2.yeah enter bootloader / fastboot with power button and volume button
4. it will work if done correctly ...if you want to flash from internal storage you will have to wipe and format data to decrypt internal syorage
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
Thank you again.
I tried adb sideload before but was stuck at 0%, I maybe missed something. I'll update here for the result once I can be back to PC.
Ronaldendoma said:
Thank you again.
I tried adb sideload before but was stuck at 0%, I maybe missed something. I'll update here for the result once I can be back to PC.
Click to expand...
Click to collapse
ok yeah must be a mistake ..
do you understand that first you enter fastboot and boot the orange fox recovery ..only then you start the adb ..
BUT REMember first you need to toggle or activate adb from orange fox recovery (maybe you forgot this ? )
another thing it is very slow so wait very long
another thing the zip you want to flash must be in the adb folder and have the name you use
so
rename persist to persist.zip and put it in adb folder ..then put magisk zip and rename to magisk.zip :
adb sideload persist.zip
adb sideload magisk.zip
Sent from my wayne using XDA Labs
here is a photo where you need to activate adb
Sent from my wayne using XDA Labs
KevMetal said:
ok yeah must be a mistake ..
do you understand that first you enter fastboot and boot the orange fox recovery ..only then you start the adb ..
BUT REMember first you need to toggle or activate adb from orange fox recovery (maybe you forgot this ? )
another thing it is very slow so wait very long
another thing the zip you want to flash must be in the adb folder and have the name you use
so
rename persist to persist.zip and put it in adb folder ..then put magisk zip and rename to magisk.zip :
adb sideload persist.zip
adb sideload magisk.zip
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
I need to wait more, I think. Before this thread, I tried to adb sideload in TWRP but it took somewhat long and still 0%, so I just cancelled since I ran out of time.
KevMetal said:
here is a photo where you need to activate adb
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
Regarding persist.zip, I am now confused because I asked in the group if the file persist_restorer_6x.zip is universal (either pie or 10, wayne or jasmine), they said yes, and another one said no. I searched in the group and found persist_restorer_a2.zip. I checked both files and they have the same filesize and contents.
So is there a thing like a universal persist for a2/6x, either for pie or 10? Or like what you said, only relevant persist depending on the os and device?
techieboy2020 said:
Regarding persist.zip, I am now confused because I asked in the group if the file persist_restorer_6x.zip is universal (either pie or 10, wayne or jasmine), they said yes, and another one said no. I searched in the group and found persist_restorer_a2.zip. I checked both files and they have the same filesize and contents.
So is there a thing like a universal persist for a2/6x, either for pie or 10? Or like what you said, only relevant persist depending on the os and device?
Click to expand...
Click to collapse
it is the same device.. so it is cross compatible ..it might just give an error if it checks the build prop ..obviously flash the A2..pie or q will just maybe be updated version or not but bettrr to flash corresponding if it exists
Sent from my wayne using XDA Labs
KevMetal said:
it is the same device.. so it is cross compatible ..it might just give an error if it checks the build prop ..obviously flash the A2..pie or q will just maybe be updated version or not but bettrr to flash corresponding if it exists
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
I see. I can't access my PC yet, but what if I still got bootloop after trying those steps, what must I do next? I'm worried for step #10.
Regarding the persist.zip, can you please check the zips below? The two have the same filesize and files inside, so maybe the two are just the same.
techieboy2020 said:
I see. I can't access my PC yet, but what if I still got bootloop after trying those steps, what must I do next? I'm worried for step #10.
Regarding the persist.zip, can you please check the zips below? The two have the same filesize and files inside, so maybe the two are just the same.
Click to expand...
Click to collapse
those are empty and won't work ..use this
https://www.dropbox.com/s/mimt4go8fert44c/persist good.zip?dl=0
Sent from my wayne using XDA Labs
KevMetal said:
those are empty and won't work ..use this
https://www.dropbox.com/s/mimt4go8fert44c/persist good.zip?dl=0
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
Ok thank you so much. Will try this tomorrow.
Regarding the state of my device, I can't boot to system because of bootloop. If I press power and volume +, I got no command. If I press power and volume -, fastboot mode. My device's bootloader is already unlocked, and can be detected through fastboot.
techieboy2020 said:
Ok thank you so much. Will try this tomorrow.
Regarding the state of my device, I can't boot to system because of bootloop. If I press power and volume +, I got no command. If I press power and volume -, fastboot mode. My device's bootloader is already unlocked, and can be detected through fastboot.
Click to expand...
Click to collapse
you don't need to boot to system ...just boot the revovery and flash the zip ..
Sent from my wayne using XDA Labs
KevMetal said:
you don't need to boot to system ...just boot the revovery and flash the zip ..
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
Got it. So the zip is compatible for either Pie or Android 10?
What's the best version for Miflash tool? I tried the newer version but it can't detect my device, and only the older version can detect. But it seems that the older version can't be trusted also since I still got persist error before.
For #10, my device will bootloop 4 to 5 times. So will it automatically turn off and on again until it will successfully boot? How long does it normally boot?
UPDATE:
KevMetal said:
you don't need to boot to system ...just boot the revovery and flash the zip ..
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
UPDATE:
So I flashed the Pie Rom (V.10.0.17.0) in the MiFlash Tool (v. 2016.04.01.0) and the flashing was successful. The device turned on and only remained at the Android One logo and turned off again. This repeated for another time and I then forced my device to fastboot mode through the buttons. I then flashed the latest Orange Fox Recovery and it was successful. Now, I checked the recovery and persist can't be mounted (can't put a check on the box), but I still continued to adb sideload mode. The sideloading for persist.zip started, but was stuck at 10%. I waited more and decided to disconnect and try to flash the zip on the device instead. I checked the active slot and it was b, so I thought changing to a will be able to mount persist. I thought that if I remain at b, I will still get mount persist error. I clicked "boot to recovery" and the screen turned off. After a while, the screen remained off and I tried to use the button combinations, and the screen was totally black (no fastboot, logo, animation, or even some light, etc). It's completely black, but I noticed that the device was still hot after a few minutes. I connected my device to the PC again and the MiFlash tool detected my device as Com10. I flashed the rom again but the flashing was not successful. I tried to uninstall the drivers and still, there is no hope for reflashing the rom (it's now detected as com4). If I try to use power combinations, the PC will make sounds like when you connect/ disconnect a device, meaning, my phone can still be detected by my PC. So is there still a hope for my phone?
techieboy2020 said:
UPDATE:
So I flashed the Pie Rom (V.10.0.17.0) in the MiFlash Tool (v. 2016.04.01.0) and the flashing was successful. The device turned on and only remained at the Android One logo and turned off again. This repeated for another time and I then forced my device to fastboot mode through the buttons. I then flashed the latest Orange Fox Recovery and it was successful. Now, I checked the recovery and persist can't be mounted (can't put a check on the box), but I still continued to adb sideload mode. The sideloading for persist.zip started, but was stuck at 10%. I waited more and decided to disconnect and try to flash the zip on the device instead. I checked the active slot and it was b, so I thought changing to a will be able to mount persist. I thought that if I remain at b, I will still get mount persist error. I clicked "boot to recovery" and the screen turned off. After a while, the screen remained off and I tried to use the button combinations, and the screen was totally black (no fastboot, logo, animation, or even some light, etc). It's completely black, but I noticed that the device was still hot after a few minutes. I connected my device to the PC again and the MiFlash tool detected my device as Com10. I flashed the rom again but the flashing was not successful. I tried to uninstall the drivers and still, there is no hope for reflashing the rom (it's now detected as com4). If I try to use power combinations, the PC will make sounds like when you connect/ disconnect a device, meaning, my phone can still be detected by my PC. So is there still a hope for my phone?
Click to expand...
Click to collapse
all of this couldn't happen if you only flashed permissiver ..what rom did you previously flash in slot b
anyway doesn't matter ..boot to fastboot with buttons ..boot ..NOT FLASH orange fox recovery
do all wipes
format data
install custom rom
install magisk
install persist
reboot to other standby slot ..
do all wipes
format data
install custom rom
install magisk
install persist
then reboot and phone will boot
use a latest custom rom Q with gapps included ....
follow all the instructions ..not only some ..don change them ..if it fails message me with screenshot
but the 10% problem over usb is a hardware , computer or most likely cable problem ..get a new cable ..or maybe you changed or damaged your screen improperly ..
anyway try the above
also download the most newest copy of miflash and use that to install drivers and flash if you want to flash stock and flash the latest stock amdroid ..
if your phone doesn't go into fastboot it is cos it is bricked in edl mode ..so flash latest stock with latest miflash ..
THEN FLASH PERSIST BY ONLY BOOTINGBrecovery
did you try to convert this A2 to Wayne amd triggered arb ? that could be why flashing stock pie goes to edl mode
Sent from my wayne using XDA Labs
Just FYI:
Since 10.0.2.0 till now I thought that persist.img is version-insensitive, as I flashed persist.img taken from 8.1 ROM into couple of versions of 9.0 without any problems (via my method published in "Guides...").
Last week I noticed that compass is "showing south", and tried to flash various versions of persist.img into active 11.0.12.0 - and was surprised to encounter "white screen of eternal booting" with non-native version of persist.img. So finally had to flash persist.img taken from 11.0.12.0 fastboot ROM image.
(Btw, my problem with compass seems to have 2 sides -1st is somewhat very big deviation at homeplace, and 2nd is that only 1st magnetic sensor is being calibrated while second magnetic sensor is not being calibrated by means I used).
KevMetal said:
all of this couldn't happen if you only flashed permissiver ..what rom did you previously flash in slot b
anyway doesn't matter ..boot to fastboot with buttons ..boot ..NOT FLASH orange fox recovery
do all wipes
format data
install custom rom
install magisk
install persist
reboot to other standby slot ..
do all wipes
format data
install custom rom
install magisk
install persist
then reboot and phone will boot
use a latest custom rom Q with gapps included ....
follow all the instructions ..not only some ..don change them ..if it fails message me with screenshot
but the 10% problem over usb is a hardware , computer or most likely cable problem ..get a new cable ..or maybe you changed or damaged your screen improperly ..
anyway try the above
also download the most newest copy of miflash and use that to install drivers and flash if you want to flash stock and flash the latest stock amdroid ..
if your phone doesn't go into fastboot it is cos it is bricked in edl mode ..so flash latest stock with latest miflash ..
THEN FLASH PERSIST BY ONLY BOOTINGBrecovery
did you try to convert this A2 to Wayne amd triggered arb ? that could be why flashing stock pie goes to edl mode
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
So I was able to use another laptop, and I managed to install adb, drivers, and MiFlash Tool. The 2018 version can now detect my phone, and I can now at least boot into fastboot. But my flashing is still not successful because I got stuck at system.img. The laptop freezes and I already tried to free up space in C: drive.
Hi everyone, and a happy new year
I need some light please, i don't understand what i'm doing wrong :/
To follow this post, i can't install EU ROM anymore (via TWRP) and i don't know why...
1) i flash the EEA Global via MiFlashTool, all ok
2) i make sure to unlock bootloader, all ok
3) i flash TWRP (official 3.6), all ok
Finally i want to flash 12.5.20.0, or 12.5.17.0 of EU ROM via TWRP/install, the process end up nicelly, no error so reboot, now everytime /data is lost, so it only boot on twrp and nothing is here anymore, need to go back at 1)
That is so frustrating :/
Can anyone enlight me please ?
did you format data after flashing 12.5.20.0
marcel112 said:
did you format data after flashing 12.5.20.0
Click to expand...
Click to collapse
nope, i need to ?
(if i format data, then i'll need to reflash the rom, right ?)
Only fastboot Version available right now bro. Already using it.
If you want to flash 12.5.20 it's impossible to use TWRP.. it's android 12 and fastboot only
marcel112 said:
If you want to flash 12.5.20 it's impossible to use TWRP.. it's android 12 and fastboot only
Click to expand...
Click to collapse
Thanks both of you !
Ok, but when i see files like 12.5.20.0 with a twrp flashing procedure labelled Mi11 Ultra, that let me think i can do it that way, it's misleading, at least :/
So, i flashed the latest 12.6 xiaomi eu rom and it worked
New problem, i then try to use twrp to flash magisk, i do fastboot boot twrp.img and then, /data lost again, so impossible to flash magisk :/
I tried both 3.6 official and 3.5.1 unofficial
p.s.: never set security pin/pass or whatever atm, so it's not a problem with the password
why do you want to try twrp to flash magisk?
copy the boot file from fastboot / images folder to your phone.
boot system, open magisk app, choose install, and search the boot file, patch. once patched, copy the file to the fhe pc.
reboot to fastboot
just type fastboot flash boot yourpatchedbootfile.img
you can type fastboot flash boot and drag the patched file to fastboot line
marcel112 said:
why do you want to try twrp to flash magisk?
copy the boot file from fastboot / images folder to your phone.
boot system, open magisk app, choose install, and search the boot file, patch. once patched, copy the file to the fhe pc.
reboot to fastboot
just type fastboot flash boot yourpatchedbootfile.img
you can type fastboot flash boot and drag the patched file to fastboot line
Click to expand...
Click to collapse
Oh my god, i totally forgot this method
Thank you very much, seems to work !
Solved
I have flashed TWRP to recovery (on my unlocked Redmi Note 10 Pro) and can access it no problem. But I have no TWRP folder on my phone and cannot see one when connected to my computer.
I have reflashed to try to fix it, but no change. I found a thread where the suggested terminal commands but I would need to root my phone and I don't think that is something I should be doing. Any suggestions?
31272809 said:
I have flashed TWRP to recovery (on my unlocked Redmi Note 10 Pro) and can access it no problem. But I have no TWRP folder on my phone and cannot see one when connected to my computer.
I have reflashed to try to fix it, but no change. I found a thread where the suggested terminal commands but I would need to root my phone and I don't think that is something I should be doing. Any suggestions?
Click to expand...
Click to collapse
I think you can't access internal storage in case of encryption.
Google about decryption pros cons ... if you're fine with decryption check out dfe in our forum
Laptapper said:
I think you can't access internal storage in case of encryption.
Google about decryption pros cons ... if you're fine with decryption check out dfe in our forum
Click to expand...
Click to collapse
I read about that but I thought I'd see 0MB or weird filenames while looking at the filesystem in TWRP recovery and neither is the case. I did have to enter my password the first time I used TWRP and I have never been asked for it since.
31272809 said:
I read about that but I thought I'd see 0MB or weird filenames while looking at the filesystem in TWRP recovery and neither is the case. I did have to enter my password the first time I used TWRP and I have never been asked for it since.
Click to expand...
Click to collapse
Which recovery you've installed? Try newest orange fox
Laptapper said:
Which recovery you've installed? Try newest orange fox
Click to expand...
Click to collapse
So I had twrp 3.6_11-sweet installed. I just flashed Orange fox (the latest stable version) to recovery, and then I could no longer access recovery - it just restarted to flashboot. I had this problem when I tried to flash the Pixel Experience image too.
So I flashed TWRP to recovery again and everything is back to normal. But the problem is that I can’t use TWRP because there’s no folder installed.
31272809 said:
So I had twrp 3.6_11-sweet installed. I just flashed Orange fox (the latest stable version) to recovery, and then I could no longer access recovery - it just restarted to flashboot. I had this problem when I tried to flash the Pixel Experience image too.
So I flashed TWRP to recovery again and everything is back to normal. But the problem is that I can’t use TWRP because there’s no folder installed.
Click to expand...
Click to collapse
How you exactly flashed recovery?
Orange fox is working quite good....
Laptapper said:
How you exactly flashed recovery?
Orange fox is working quite good....
Click to expand...
Click to collapse
So I put the phone in fastboot mode -> connected to PC with usb -> check connection in cmd (fastboot devices) -> fastboot flash recovery "recovery_orange fox.img" -> power+up
And I get sent back to the fastboot screen
I must be doing something wrong but I have watched videos and read instructions and I don't know what it is.
31272809 said:
So I put the phone in fastboot mode -> connected to PC with usb -> check connection in cmd (fastboot devices) -> fastboot flash recovery "recovery_orange fox.img" -> power+up
And I get sent back to the fastboot screen
I must be doing something wrong but I have watched videos and read instructions and I don't know what it is.
Click to expand...
Click to collapse
Sounds ok
But without the quotes and no spaces, means change the file name like cmd:
fastboot flash recovery orangefox.img
Laptapper said:
Sounds ok
But without the quotes and no spaces, means change the file name like cmd:
fastboot flash recovery orangefox.img
Click to expand...
Click to collapse
I renamed the file but same result - it cycles through back to fastboot instead of recovery.
I don't understand. It's like it only accepts the twrp image, but even that doesn't install right.
31272809 said:
I renamed the file but same result - it cycles through back to fastboot instead of recovery.
I don't understand. It's like it only accepts the twrp image, but even that doesn't install right.
Click to expand...
Click to collapse
Please make a pc screenshot from flashing progress
You've switched on developer option usb debugging?
Laptapper said:
Please make a pc screenshot from flashing progress
You've switched on developer option usb debugging?
Click to expand...
Click to collapse
Here's the screenshot. Inbetween flashing recoveryorangefox.img and twrp.img I have tried to reboot into recovery and I have been sent back to fastboot.
Yes, usb debugging is on in the settings.
31272809 said:
Here's the screenshot. Inbetween flashing recoveryorangefox.img and twrp.img I have tried to reboot into recovery and I have been sent back to fastboot.
Yes, usb debugging is on in the settings.
Click to expand...
Click to collapse
Check out here
How to Enter Recovery Mode ? Volume Up and Power enabling Fastboot
Today I flashed EU RoM 13.0.4 to my Redmi Note 10 pro . Phone is working fine but I installed orange recovery and the process completed successfully on pc . When I press power and volume up it going to Fastboot mode instead of recovery mode. How...
forum.xda-developers.com
And take the files which there are downloadable
Try after flashing to boot via hardware keys and also via adb.
If both not working, I think you have to flash fastboot image via PC miflash and boot it to switch developer usb debugging on and restart to fastboot mode and flash twrp again.....
31272809 said:
Here's the screenshot. Inbetween flashing recoveryorangefox.img and twrp.img I have tried to reboot into recovery and I have been sent back to fastboot.
Yes, usb debugging is on in the settings.
Click to expand...
Click to collapse
One more idea, before starting from scratch:
After flashing twrp disconnecting usb and then rebooting to recovery by pressing power and vol+ until you'll see the logo and feel the vibration
Why don't you test the recovery using fastboot boot? My recommendation is never to flash any recovery before successfully having it started manually once.
My personal approach is, never to install any recovery but only boot it in case it is needed. Disadvantage is that you need to be near a computer if you want to run it.
fastboot flash recovery twrp-3.6.0_11-0-sweet.img
fastboot boot twrp-3.6.0_11-0-sweet.img
Ashle said:
fastboot flash recovery twrp-3.6.0_11-0-sweet.img
fastboot boot twrp-3.6.0_11-0-sweet.img
Click to expand...
Click to collapse
Hi all, there's been some progress but I'd like your advice before continuing. I have my preferred ROM (Pixel Experience, zipped) copied to my SD card and I can see my SD card under Install option on TWRP. My phone data has been formatted (using the twrp Wipe option). Should I try installing from the SD card? I'm nervous since I know missing steps was warned against in the installation instructions.
1. Wipe Data/Cache
2. Format Data (yes)
3. Flash ROM Pixel Experience.zip
4. Reboot System
Ashle said:
1. Wipe Data/Cache
2. Format Data (yes)
3. Flash ROM Pixel Experience.zip
4. Reboot System
Click to expand...
Click to collapse
Is 1 included in 2, or should I do something else as well?
If I'm okay to move to step 3, do I reboot to recovery or reboot into (hopefully) my new ROM?
Copy Pixel Experience.zip to sdcard
reboot to recovery
All over TWRP
1. Wipe Data/Cache
2. Format Data (yes)
3. Flash ROM Install Pixel Experience.zip
4. Reboot System
Ashle said:
Copy Pixel Experience.zip to sdcard
reboot to recovery
All over TWRP
1. Wipe Data/Cache
2. Format Data (yes)
3. Flash ROM Install Pixel Experience.zip
4. Reboot System
Click to expand...
Click to collapse
It didn't work.
Hello everyone. i just want to install Gsi on an new unlocked tab a8, after flashing twrp, I use the fastbootd mode to flash the gsi and installed the multi-disable zip. when I want to reboot to os, it stucked at bootlogo. I don't know where I am wrong, so please help me, in appreciation
WolfHRB said:
Hello everyone. i just want to install Gsi on an new unlocked tab a8, after flashing twrp, I use the fastbootd mode to flash the gsi and installed the multi-disable zip. when I want to reboot to os, it stucked at bootlogo. I don't know where I am wrong, so please help me, in appreciation
Click to expand...
Click to collapse
We don't know where you went wrong either because you didn't list the steps you took or what GSI you flashed or what stock ROM you started from. Or where you are looping.
starting firmware: X200ZCU2CWD3
Steps: 1. Unlock BL
2. flash TWRP via Odin V3.14
3. Format data partition
4. flash dm-verity disabler (File name: Disable_Dm-Verity_ForceEncrypt)
5. reboot to fastbootd mode (using TWRP reboot menu)
6. fastboot erase system
7. fastboot flash system "img path"
8. fastboot -w
9. fastboot reboot
lewmur said:
We don't know where you went wrong either because you didn't list the steps you took or what GSI you flashed or what stock ROM you started from. Or where you are looping.
Click to expand...
Click to collapse
starting firmware: X200ZCU2CWD3
Steps: 1. Unlock BL
2. flash TWRP via Odin V3.14
3. Format data partition
4. flash dm-verity disabler (File name: Disable_Dm-Verity_ForceEncrypt)
5. reboot to fastbootd mode (using TWRP reboot menu)
6. fastboot erase system
7. fastboot flash system "img path"
8. fastboot -w
9. fastboot reboot
WolfHRB said:
starting firmware: X200ZCU2CWD3
Steps: 1. Unlock BL
2. flash TWRP via Odin V3.14
3. Format data partition
4. flash dm-verity disabler (File name: Disable_Dm-Verity_ForceEncrypt)
5. reboot to fastbootd mode (using TWRP reboot menu)
6. fastboot erase system
7. fastboot flash system "img path"
8. fastboot -w
9. fastboot reboot
Click to expand...
Click to collapse
Don't flash dm-verity disabler for this device and the GSI should boot as long as it's compatible
kevinco1 said:
Don't flash dm-verity disabler for this device and the GSI should boot as long as it's compatible
Click to expand...
Click to collapse
Without this alway bootloop logo too.
1. Extract the IMG to the adb folder and rename it system.img
2. Flash TWRP with ODIN
3. When booting into TWRP using the Volume up and Power key, select reboot and then fast boot.
4. When you get there, go on your PC and open cmd with the adb folder.
5. Now type fastboot devices just make sure you have the device connect properly. Type fastboot -w after.
6. Type "fastboot flash system system.img" press enter and wait for it to finish. The last line should be be where you can type other commands.
7. When its finished, type fastboot reboot fastboot.
stradfred said:
Without this alway bootloop logo too.
1. Extract the IMG to the adb folder and rename it system.img
2. Flash TWRP with ODIN
3. When booting into TWRP using the Volume up and Power key, select reboot and then fast boot.
4. When you get there, go on your PC and open cmd with the adb folder.
5. Now type fastboot devices just make sure you have the device connect properly. Type fastboot -w after.
6. Type "fastboot flash system system.img" press enter and wait for it to finish. The last line should be be where you can type other commands.
7. When its finished, type fastboot reboot fastboot.
Click to expand...
Click to collapse
What exact GSI and build are you trying to install? There are only a few that are compatible, otherwise you're not gonna have any other luck flashing
I tryed with on my X200XXU2CWC1 firmware:
lineage-19.1-20230418-UNOFFICIAL-arm64_bgN.img
lineage-20.0-20230324-UNOFFICIAL-arm64_bgN.img
lineage-20.0-20230325-UNOFFICIAL-a64_bgN.img
Old version too but the same result...
Which version we are sure that works?
stradfred said:
I tryed with on my X200XXU2CWC1 firmware:
lineage-19.1-20230418-UNOFFICIAL-arm64_bgN.img
lineage-20.0-20230324-UNOFFICIAL-arm64_bgN.img
lineage-20.0-20230325-UNOFFICIAL-a64_bgN.img
Old version too but the same result...
Which version we are sure that works?
Click to expand...
Click to collapse
Make sure you are only trying to flash arm64 builds for this device
Both 19.1-20230418 and 20.0-20230324 do install properly but there's certain bugs that make them unfit to be used as a daily driver.
If you're looking for the latest build where everything works (including bluetooth) flash 20.0-20230218
stradfred said:
Without this alway bootloop logo too.
1. Extract the IMG to the adb folder and rename it system.img
2. Flash TWRP with ODIN
3. When booting into TWRP using the Volume up and Power key, select reboot and then fast boot.
4. When you get there, go on your PC and open cmd with the adb folder.
5. Now type fastboot devices just make sure you have the device connect properly. Type fastboot -w after.
6. Type "fastboot flash system system.img" press enter and wait for it to finish. The last line should be be where you can type other commands.
7. When its finished, type fastboot reboot fastboot.
Click to expand...
Click to collapse
You left out the step to format data and factory wipe.
lewmur said:
You left out the step to format data and factory wipe.
Click to expand...
Click to collapse
That's right!
How is it normal to do this command after having flashed a ROM ???
Once done, I boot of course on lineage after a few moments on the Samsung logo.
Which version of lineage is the most stable, 19 (Android 12) or 20 (Android 13)?
Thank you both for your help.
kevinco1 said:
If you're looking for the latest build where everything works (including bluetooth) flash 20.0-20230218
Click to expand...
Click to collapse
https://sourceforge.net/projects/andyyan-gsi/files/lineage-20-td/History/lineage-20.0-20230218-UNOFFICIAL-arm64_bgN.img.xz/download
I tried this.
stradfred said:
That's right!
How is it normal to do this command after having flashed a ROM ???
Once done, I boot of course on lineage after a few moments on the Samsung logo.
Which version of lineage is the most stable, 19 (Android 12) or 20 (Android 13)?
Thank you both for your help.
Click to expand...
Click to collapse
TWRP and fastboot can't handle the encrypted data partition. So you need to format it. Current versions of LOS re-encrypt it as soon as you boot to system. And you can't use dm-verity on this model, so you can't disable it.
stradfred said:
https://sourceforge.net/projects/andyyan-gsi/files/lineage-20-td/History/lineage-20.0-20230218-UNOFFICIAL-arm64_bgN.img.xz/download
I tried this.
Click to expand...
Click to collapse
Did you try this build before or after the realization you had left out the steps to wipe and factory reset?
Has anyone managed to install a GSI on the SM-X200 with X200XXU2CWC1 firmware? I tried different LOS 20 and LOS 19 GSIs, with and without GAPPS, including the ones mentioned earlier from March and April, but did not succeed a single time. The tablet gets always stuck in a boot loop. I flashed via TWRP and wiped and formatted data every time.
Is it possibly the vendor firmware (SW rev. 2) that prevents the GSI from running? All guides from this forum seems to relate to a SW rev. 1 firmware like X200XXS1CWA3.
mrspeccy said:
Has anyone managed to install a GSI on the SM-X200 with X200XXU2CWC1 firmware? I tried different LOS 20 and LOS 19 GSIs, with and without GAPPS, including the ones mentioned earlier from March and April, but did not succeed a single time. The tablet gets always stuck in a boot loop. I flashed via TWRP and wiped and formatted data every time.
Is it possibly the vendor firmware (SW rev. 2) that prevents the GSI from running? All guides from this forum seems to relate to a SW rev. 1 firmware like X200XXS1CWA3.
Click to expand...
Click to collapse
If you mean you used the "Install" button in TWRP to flash, then that is your mistake. The "Install" button only has the option to flash the "Super" partition and not the "System". You need to use "Fastboot" to flash the system image. I flashed from CWD2 which is even later than CWC1, so that shouldn't be a problem. If it was, then TWRP wouldn't have worked. I'm running LOS 20 20300507 bgN.
No, I used TWRP to get into fastboot mode and said fastboot flash system ...img. I have no idea what I did wrong. Previously I flashed Lineage on a couple of Samsung Tablets (SM-T510, SM-T505).
mrspeccy said:
No, I used TWRP to get into fastboot mode and said fastboot flash system ...img. I have no idea what I did wrong. Previously I flashed Lineage on a couple of Samsung Tablets (SM-T510, SM-T505).
Click to expand...
Click to collapse
There are only certain LOS builds that work with this device, you're wasting your time if you are blindly flashing random ones.
Refer to earlier posts to confirm which ones do work. And like @lewmur just reported the newest build 20300507 bgN does flash successfully
The 20230507 bgN was actually the first build I tried before I went to older variants, including the 20220814 bgN that is mentioned in a different thread.
@lewmur : Did you do a clean flash and format data before you installed the 20230507 build on the CWD2 firmware? There might be some issues with format data and the TWRP 3.7.0-12.2 from this forum (https://forum.xda-developers.com/t/...-for-2021-galaxy-tab-a8-10-5-sm-x200.4488691/) on the latest kernel. After I format data in TWRP, the tablet is recognized as writable media in Windows, but I get reading and writing errors when I try to access the about 22 GB large partition.
I know that it is impossible to roll back the bootloader to revision 1, but may it be possible that I extract and flash a kernel from the X200XXS1CWA3 to further investigate this issue?
mrspeccy said:
The 20230507 bgN was actually the first build I tried before I went to older variants, including the 20220814 bgN that is mentioned in a different thread.
@lewmur : Did you do a clean flash and format data before you installed the 20230507 build on the CWD2 firmware? There might be some issues with format data and the TWRP 3.7.0-12.2 from this forum (https://forum.xda-developers.com/t/...-for-2021-galaxy-tab-a8-10-5-sm-x200.4488691/) on the latest kernel. After I format data in TWRP, the tablet is recognized as writable media in Windows, but I get reading and writing errors when I try to access the about 22 GB large partition.
I know that it is impossible to roll back the bootloader to revision 1, but may it be possible that I extract and flash a kernel from the X200XXS1CWA3 to further investigate this issue?
Click to expand...
Click to collapse
You must do a clean flash. The purpose of formatting the data partition is to get rid of the encryption. TWRP can't handle the encryption. And LOS will re-encrypt it the first time you boot to system. As to extracting the kernel from CWA3, I don't advise doing that. It could hard brick the tablet.