Related
I just hardbricked my S5830 while trying to install cwm.
Actually I tried to install cwm without rooting the phone, and when i checked after this the phone was not going to recovery even samsung default recovery was gone.
Now there was no way through phone to install cwm. So i tried to factory reset the phone. My bad luck, phone is not getting on now.
The problem I am facing now is I am not able to use odin as drivers are not recognising the phone. It always gives drivers malfunctioned error. Even for the adb drivers too.
Has anybody faced this issue?
It is going to download mode. But in pc it is not recognising the phone. I installed all the available drivers.. But still the same.
Thank you in advance.
sie4kor said:
I just hardbricked my S5830 while trying to install cwm.
Actually I tried to install cwm without rooting the phone, and when i checked after this the phone was not going to recovery even samsung default recovery was gone.
Now there was no way through phone to install cwm. So i tried to factory reset the phone. My bad luck, phone is not getting on now.
The problem I am facing now is I am not able to use odin as drivers are not recognising the phone. It always gives drivers malfunctioned error. Even for the adb drivers too.
Has anybody faced this issue?
It is going to download mode. But in pc it is not recognising the phone. I installed all the available drivers.. But still the same.
Thank you in advance.
Click to expand...
Click to collapse
Have a look in the rooting and troubleshooting threads.
If odin isn't recognising your phone then:
1/ drivers for "download-mode" not installed properly.
2/ phone is not actually in download-mode.
3/ usb cable or pc usb port is faulty.
Ri9000 said:
Have a look in the rooting and troubleshooting threads.
If odin isn't recognising your phone then:
1/ drivers for "download-mode" not installed properly.
2/ phone is not actually in download-mode.
3/ usb cable or pc usb port is faulty.
Click to expand...
Click to collapse
I am glad you replied.
I think the drivers for download mode has not installed properly.
I searched in rooting and trouble shooting, couldnt find the proper drivers which detects. Even i installed windows 7 as someone mentioned in some thread. Still nothing worked.
sie4kor said:
I am glad you replied.
I think the drivers for download mode has not installed properly.
I searched in rooting and trouble shooting, couldnt find the proper drivers which detects. Even i installed windows 7 as someone mentioned in some thread. Still nothing worked.
Click to expand...
Click to collapse
1/ All I can suggest is install drivers/ odin as administrator. Windows should detect running phone with "ding-dong" even in wrong mode.
2/ remove phone battery for 20 secs.
3/ replace battery.
4/ press and hold down home button, down-Volume & then press power for 4 secs, then release power.
5/ keep holding home and down-Volume (about 5 more secs) until screen flashes and "downloading" is displayed.
6/ release buttons, plug phone to pc, flash stock rom with odin.
I'm in a big predicament. A few weeks ago I installed the MOAR ROM on my Note 5. After installing this ROM I was no longer able to connect my phone to PC. I tried a Windows 8 PC which says I have an unrecognized USB device plugged in. I tried going into Developer settings to set USB mode to MTP but the option didn't exist. I had all USB drivers installed as well. My wife's phone is recognized no problem. When plugging the phone into my linux machine absolutely nothing happened. It used to show the phone in the left navigation panel in my window manager but after installing MOAR ROM it was no longer detected.
Anyway, today I was trying to play Cartoon Wars 3 and since my phone is rooted it wouldn't let me play. I decided to go into the Super User app and disable it to see if the game would work and it didn't. When I went to re-enable the app it said installation failed and asked me to reboot. I clicked reboot and was sent into a boot loop. I thought okay no big deal, I'll just restore a backup in TWRP. When I go to restore the backup and select the backup file it asks which partitions to restore, but there are no boxes to check. It usually has options like system and data but now it's just blank. I tried a factory reset and I'm still in a bootloop. I'm at a complete loss. I don't know what else to do. I've tried download mode and everything but no matter what I do my phone isn't detected by my pc.
I appreciate any help. I don't know what to do. I'm out of a phone right now and don't have a backup. Not to mention I'm in between jobs right now and can't afford a new one right now.
Just flash a stock rom from sammobile.com
Pre req:
*Odin(any vers)
*Stock rom
Steps
*Extract the downloaded stock rom in your PC
*In twrp wipe everything except internal, then boot in to download mode.
*Once in download mode, connect your phone to your pc, then open Odin.
*In Odin, check the "AP" section and locate the downloaded stock rom(the extracted one)
*Hit start.
Hpe that helps
herculesPh said:
Just flash a stock rom from sammobile.com
Pre req:
*Odin(any vers)
*Stock rom
Steps
*Extract the downloaded stock rom in your PC
*In twrp wipe everything except internal, then boot in to download mode.
*Once in download mode, connect your phone to your pc, then open Odin.
*In Odin, check the "AP" section and locate the downloaded stock rom(the extracted one)
*Hit start.
Hpe that helps
Click to expand...
Click to collapse
Thank you for your reply but it seems you didn't read my post. My phone is not recognized by any pc.
What is the terminal command to restore a backup? That's pretty much my last ditch effort.
Well I broke my recovery so I'm screwed. I contacted Samsung and they said they would service it for free. Wish me luck.
What would cause the phone to stop being recognized by the PC? I narrowed it down to the MTP software or the micro usb charge port. My Windows computer says Device Descriptor Request Failed. Linux box does nothing. No USB devices are listed when I run lsblk.
weinerwad3000 said:
I'm in a big predicament. A few weeks ago I installed the MOAR ROM on my Note 5. After installing this ROM I was no longer able to connect my phone to PC. I tried a Windows 8 PC which says I have an unrecognized USB device plugged in. I tried going into Developer settings to set USB mode to MTP but the option didn't exist. I had all USB drivers installed as well. My wife's phone is recognized no problem. When plugging the phone into my linux machine absolutely nothing happened. It used to show the phone in the left navigation panel in my window manager but after installing MOAR ROM it was no longer detected.
Anyway, today I was trying to play Cartoon Wars 3 and since my phone is rooted it wouldn't let me play. I decided to go into the Super User app and disable it to see if the game would work and it didn't. When I went to re-enable the app it said installation failed and asked me to reboot. I clicked reboot and was sent into a boot loop. I thought okay no big deal, I'll just restore a backup in TWRP. When I go to restore the backup and select the backup file it asks which partitions to restore, but there are no boxes to check. It usually has options like system and data but now it's just blank. I tried a factory reset and I'm still in a bootloop. I'm at a complete loss. I don't know what else to do. I've tried download mode and everything but no matter what I do my phone isn't detected by my pc.
I appreciate any help. I don't know what to do. I'm out of a phone right now and don't have a backup. Not to mention I'm in between jobs right now and can't afford a new one right now.
Click to expand...
Click to collapse
you can try this code and test if it work
*#0808#
Familiaaa said:
you can try this code and test if it work
*#0808#
Click to expand...
Click to collapse
The phone does not boot. Recovery does not boot. The only thing the phone does is go into download mode. The phone does not connect to any computer so I cannot use odin.
weinerwad3000 said:
The phone does not boot. Recovery does not boot. The only thing the phone does is go into download mode. The phone does not connect to any computer so I cannot use odin.
Click to expand...
Click to collapse
when your phone is in download mode,it doesn't work to connect it with samsung kies on your pc?
You could try using the Kies software to reload the stock firmware. Here's an overview of what to do:
- if you don't already have the Kies software installed on your PC, download it (just search Google) and install it. The first time it runs it'll update itself to the latest version so make sure you run it once before proceeding.
- put your phone in Download mode: with the phone completely off, press and hold the Volume Down and Home and Power buttons simultaneously, and release them all when you see the Samsung splash screen
- connect the phone to your PC with the USB cable that came with the phone
-- if you've never had the phone connected to your Windows-based computer before, you'll see messages about installing drivers, etc - just wait until this is done (may take 5 or 10 minutes) [I don't know what happens if you have a Mac - it probably just works]
- in the Kies software, select the second item in the Tools menu and just follow the prompts to enter the model number (in CAPS) and IMEI/Serial Number (both found under the battery - it's ok to remove the battery at this point)
- the Kies software should start downloading the correct firmware for your phone from the Internet; once that's done (depending on your Internet connection speed) it'll begin downloading that to the phone (this probably takes 10 minutes or so)
jubei79 said:
when your phone is in download mode,it doesn't work to connect it with samsung kies on your pc?
You could try using the Kies software to reload the stock firmware. Here's an overview of what to do:
- if you don't already have the Kies software installed on your PC, download it (just search Google) and install it. The first time it runs it'll update itself to the latest version so make sure you run it once before proceeding.
- put your phone in Download mode: with the phone completely off, press and hold the Volume Down and Home and Power buttons simultaneously, and release them all when you see the Samsung splash screen
- connect the phone to your PC with the USB cable that came with the phone
-- if you've never had the phone connected to your Windows-based computer before, you'll see messages about installing drivers, etc - just wait until this is done (may take 5 or 10 minutes) [I don't know what happens if you have a Mac - it probably just works]
- in the Kies software, select the second item in the Tools menu and just follow the prompts to enter the model number (in CAPS) and IMEI/Serial Number (both found under the battery - it's ok to remove the battery at this point)
- the Kies software should start downloading the correct firmware for your phone from the Internet; once that's done (depending on your Internet connection speed) it'll begin downloading that to the phone (this probably takes 10 minutes or so)
Click to expand...
Click to collapse
Kies doesn't work either. I already tried that. When I hook up the phone It says "Device Descriptor Request Failed". It used to connect to my computers until I put MOAR ROM on the phone. Since then it stopped being recognized by my computers. There's either something wrong with the connection or something got corrupted.
weinerwad3000 said:
Kies doesn't work either. I already tried that. When I hook up the phone It says "Device Descriptor Request Failed". It used to connect to my computers until I put MOAR ROM on the phone. Since then it stopped being recognized by my computers. There's either something wrong with the connection or something got corrupted.
Click to expand...
Click to collapse
What have you already tried?
- are you sure you're using a data cable and not a charging-only cable?
- have you tried a different computer?
- have you installed the Kies software?
- what does Device Manager show when the phone is connected?
- assuming that the phone is working normally, does the phone show anything when you connect it?
- do you have try windows 8 or 10?
can be you found a solution in this forum
http://forums.androidcentral.com/sa...-not-being-recognised-download-mode-odin.html
jubei79 said:
What have you already tried?
- are you sure you're using a data cable and not a charging-only cable?
- have you tried a different computer?
- have you installed the Kies software?
- what does Device Manager show when the phone is connected?
- assuming that the phone is working normally, does the phone show anything when you connect it?
- do you have try windows 8 or 10?
can be you found a solution in this forum
http://forums.androidcentral.com/sa...-not-being-recognised-download-mode-odin.html
Click to expand...
Click to collapse
I've tried 4 different cables. My wife's S5 works perfectly fine on all computers. I have tried in Windows 7, 8, 8.1, and 10. I've also tried in Linux Mint. It used to work until I installed MOAR Rom. Windows says Device Descriptor Request Failed. Linux doesn't do anything when hooked up. lsblk doesn't show the device either.
I have a bit of an update. Apparently something happened with all my data cables. I hooked up my wife's phone the other day and I was all of a sudden receiving the same error as the note 5. I went out and bought a new data cable and now her phone connects again. I'm waiting for the Note 5 to charge up so I can try Odin. I'll post back my results.
I apologize to those who told me it was the cable. I just didn't see that it was conceivable that all 4 of my data cables were all of a sudden damaged. Never underestimate the ability of children to destroy every working cable you own.
Well I'm still getting the error. I have some usb cables coming in the mail so once i try those out I'll get back to everyone.
weinerwad3000 said:
Well I'm still getting the error. I have some usb cables coming in the mail so once i try those out I'll get back to everyone.
Click to expand...
Click to collapse
Were you able to fix your issue. I have the same issue. Note 5 N9208, I can get into Recovery (TWRP) and Download mode, but can not boot. The USB connection is showing USB Device Descriptor failed. I have tried 5 different cables and Windows 7/10 Ubuntu and cant get the phone to show up on the PC. I also have changed the USB port of the phone. Any insight would be helpful.
musab_bari said:
Were you able to fix your issue. I have the same issue. Note 5 N9208, I can get into Recovery (TWRP) and Download mode, but can not boot. The USB connection is showing USB Device Descriptor failed. I have tried 5 different cables and Windows 7/10 Ubuntu and cant get the phone to show up on the PC. I also have changed the USB port of the phone. Any insight would be helpful.
Click to expand...
Click to collapse
I ended up trying to replace the port and accidentally cut the ribbon for the LCD screen. Ended up getting a new phone.
Hello!
I am a happy owner of a OP3T 128GB version, but I've currently ran into an interesting issue . I am familiar with rooting android, fastboot, adb and stuff and I have limited experience (a begginer, but a quick learner ) with some other android phones. I hope I'm not creating a duplicit question - I am really sorry if I am, but I haven't found a solution to my problem even after hours spend behind the desk.
Long story short - accidentaly did an Advanced wiped in TWRP (3.1.1-0) and wiped my system (OS) and everything in the phone. I don't really care about the data, but checking the Sysem box in Advanced wipe menu has brought me into serious trouble it seems. Of course, I got a bootloop - my bad, right , nothing I can't fix I thought... But when I approached to try to flash a zip or .img of a system file/stock ROM respectively, I found literally no way to do so. My phone isn't recognized by my PC(s) (Windows and Mac) and I tried everything I could. The device isn't even a Qualcomm or sth. in the device manager - simply nothing, I can only get the device to charge sometimes when connected to the PC (seen in TWRP). I cannot connect an USB key to it via OTG either in TWRP to flash from there - TWRP just does not seem to know I even plugged a USB into the phone. I tried OP drivers, adb naked drivers, the phone and the PC just don't seem to be communicating at all.
The device can boot into fastboot, recovery (TWRP) and if proceeded TWRP prompts with "No OS installed" and I get a bootloop as expected. Is there any way I could try to flash the device with proper firmware? I do have the firmware and everything, I just can't seem to find a way how to flash it . I am a young student who just likes to play with tech stuff and devices and messed up and cannot help myself and I am really hopeless at this point . Any advice is greatly appriciated.
Thank you so much.
Matus
If you can flash/boot into TWRP, then probably nothing is lost. While in TWRP, if you connect your phone with PC, what happens? Do you hear the usual USB connection sound? If yes, what appears in the device manager?
Even if it doesn't appear in device manager, don't worry.
Boot into TWRP, go to storage, DISABLE MTP and enable it again. I know it sounds dumb, but just try it. It will be recognized as long as you have the proper drivers installed.
After that copy the zip of an OxygenOS based ROM like FreedomOS and flash it. Don't wipe anything. It will boot fine. I've done that a few times, never had a problem.
Thanks for the advice guys - no, no sound, nothing - as I said, I only get the charging (+) icon in twpr next to the battery percentage.
I did disable and enable MTP before - although not plugged in a pc during the process - will try if I have the chance.
One more thing that might ring a bell for someone - I tried the key combo for hard reset today(power + vol down) for a couple second and moments later I got a fuzzy (random colored pixels) screen and a red led. Weird, if you ask me.
P.S.: Today I tried to chat with OP a bit - 230 Eur for a new MB (64GB) and 255 Eur for my 128GB version - I just wanted to know, I'm still not admitting failure though. But as a student, these numbers from the support literally hurt me when reading...
grello said:
Hello!
I am a happy owner of a OP3T 128GB version, but I've currently ran into an interesting issue . I am familiar with rooting android, fastboot, adb and stuff and I have limited experience (a begginer, but a quick learner ) with some other android phones. I hope I'm not creating a duplicit question - I am really sorry if I am, but I haven't found a solution to my problem even after hours spend behind the desk.
Long story short - accidentaly did an Advanced wiped in TWRP (3.1.1-0) and wiped my system (OS) and everything in the phone. I don't really care about the data, but checking the Sysem box in Advanced wipe menu has brought me into serious trouble it seems. Of course, I got a bootloop - my bad, right , nothing I can't fix I thought... But when I approached to try to flash a zip or .img of a system file/stock ROM respectively, I found literally no way to do so. My phone isn't recognized by my PC(s) (Windows and Mac) and I tried everything I could. The device isn't even a Qualcomm or sth. in the device manager - simply nothing, I can only get the device to charge sometimes when connected to the PC (seen in TWRP). I cannot connect an USB key to it via OTG either in TWRP to flash from there - TWRP just does not seem to know I even plugged a USB into the phone. I tried OP drivers, adb naked drivers, the phone and the PC just don't seem to be communicating at all.
The device can boot into fastboot, recovery (TWRP) and if proceeded TWRP prompts with "No OS installed" and I get a bootloop as expected. Is there any way I could try to flash the device with proper firmware? I do have the firmware and everything, I just can't seem to find a way how to flash it . I am a young student who just likes to play with tech stuff and devices and messed up and cannot help myself and I am really hopeless at this point . Any advice is greatly appriciated.
Thank you so much.
Matus
Click to expand...
Click to collapse
1) try to update the twrp to the official 3.1.1.0. Then flash the latest modem firmware for your device and try to flash a custom rom like lineage os (a 7.x rom)
If you connect the phone to PC in TWRP and your phone is not recognized, chances are good that either your phone's USB or the cable (or the USB port on the computer) is not working. You can try to download the adb driver installer from here, just to check if your phone is listed by the installer: http://adbdriver.com/downloads/
Update - tried the MTP Enable/disable option in TWRP (in the Mount menu) while plugged into the PC, with no luck
IvanPrince - have you actually read the description of my problem? I have the 3.1.1-0 and even if not, how should I actually flash another version of twrp? The problem here is I cannot seem to find a WAY how to flash ANYTHING on the device.
I'll see about the adb drivers and update.
Thanks all,
Does the phone show up as anything on the PC when you boot to fastboot? I re-read but didn't see anything about it.
Nope - nothing. By now, I believe it is a hardware problem as the phone indeed got wet before my mistake with the advanced wipe. It appears to work just fine though, apart from the connectivity issue, so I believe the MB should be ok as everything else, including the screen is.
I just have one, perhaps a little courageous thing I'd like to ask from someone kind enough. Anyone with a Oneplus 3 or 3T who's not afraid to open the phone for a couplne minutes and has a multimeter alongside with a USB cable should be able to help me. :angel:
Could you, my awesome stranger, check where the 4 USB pins (on the side where you plug them into the PC) lead (make contact/'BEEP' on the multimeter) with the actual phone motherboard? It would REALLY help me in troubleshooting and perhaps saving 250 Eur. So far, I have this: (same color means contact) at that point. See picture.
BLACK - GND (all the heatsinks are connected to GROUND as well)
GREEN - DATA +
YELLOW - DATA -
RED - VCC
If anyone decides to open up their phone and help out a fellow xda guy, it will be greatly appriciated. :angel:
Hey Bro I was curious to know if you tried this method of recovering from a hard brick... When I first got my 3t something similar happened to me. I can't remember all the details of my hard brick but I thought I was f***ed. Please try this if you have not already.
https://forum.xda-developers.com/oneplus-3t/how-to/unbrick-unbrick-tutorial-oneplus-3t-t3515306
Might be a dumb question, but you did remember to mount the USB when you connected the otg right?
If the bootloader is unlocked, you can save it.
I would flash the stock recovery and the latest factory image (4.1.7)
Download them both from here:
http://downloads.oneplus.net/oneplus-3t/oneplus_3t_oxygenos_4.1.7/
After flashing the stock recovery using fastboot, boot to stock recovery and sideload through ADB the stock factory image.
Reboot and after checking that everything is working fine, feel free to relock the bootloader if you wish to stay 100% stock.
If the computer doesn't recognize it at all then it's a driver problem, not the phone... at least that's what I think.
try to use the program to fix my oneplus 3t it said download complete. try to restart
try to use the program to fix my oneplus 3t it said download complete. try to restart it and can press the screen and it keep rebooting it like the screen is frozen
please help me out
So, I tried to update to Pie.
I was on Stock Oreo rooted without encryption.
Wiped everything except sdcard, installed Pie and the boot img for encryption fix.
Rebooted to TWRP, flashed the zip from verity fix, flashed latest Magisk.
Rebooted to system, stuck with the dots rotating.
Tried to redo it again, adding the step for the firmware flash.
But when wiping i accidentally wiped sdcard too, so I have no more the required files inside TWRP.
Tried to connect both TWRP and bootloader via adb/fastboot but phone is not recognized.
All the drivers are installed it always worked before (Win7).
Now everytime I try to connect the 3T to PC it says Unknown Device in Device Manager, but all the drivers are installed.
Apparently the phone is not sending its data, because in device properties i see VID & PID = 0000.
Trying to manually attach a driver to it (with right click, update driver) gives error, no driver available for the device (using any adb drivers .inf).
So basically now I'm stuck with a phone without files in it, but with only TWRP working.
How can I send the rom files without adb/fastboot? Any trick?
I also tried to use USB OTG from TWRP but apparently any usb stick is not recognized.
Tried different USB ports and different cables. Seems like a problem with the phone usbC port, not sure.
It's an hard brick at this point?
Just go with the Qualcomm factory restore mode/tools. Turn off phone, hold volume up while connecting phone to PC, install the drivers for the Qualcomm 9008 device and then run the factory recover tool. You can find out all this in the factory restore thread, just make sure you have the 3t and not the normal 3 as they have different firmwares for the hardware.
Skickat från min ONEPLUS A3003 via Tapatalk
Format the device in latest TWRP and reboot it back to TWRP then connect the USB cable to PC. It should ideally recognize your 3t. I never had any issue while recognizing the phone in TWRP menu.
if nothing helps, the final step is obviously try he Qualcomm factory restore mode/tools.
pitrus- said:
Just go with the Qualcomm factory restore mode/tools. Turn off phone, hold volume up while connecting phone to PC, install the drivers for the Qualcomm 9008 device and then run the factory recover tool. You can find out all this in the factory restore thread, just make sure you have the 3t and not the normal 3 as they have different firmwares for the hardware.
Skickat från min ONEPLUS A3003 via Tapatalk
Click to expand...
Click to collapse
sandeep_kumar said:
Format the device in latest TWRP and reboot it back to TWRP then connect the USB cable to PC. It should ideally recognize your 3t. I never had any issue while recognizing the phone in TWRP menu.
if nothing helps, the final step is obviously try he Qualcomm factory restore mode/tools.
Click to expand...
Click to collapse
I already tried that too. It always appear as unknown device, even with that method.
Just to be clear, I never had problem before and I already used TWRP mount and fastboot/adb to load files without having a running ROM. I was always able to move file with any of them.
This is different, it seems like an hw problem, the phone it's not sending his IDs when connecting to CP so the PC can't identify what it is even if drivers are installed.
Now, I'm not sure if the problem lies in the physical USBC port or if the failed Pie upgrade ruined somethin in the bootloader or something else.
Then I'd say broken USB cable, have you tried with another cable or a shorter cable?
Skickat från min ONEPLUS A3003 via Tapatalk
pitrus- said:
Then I'd say broken USB cable, have you tried with another cable or a shorter cable?
Skickat från min ONEPLUS A3003 via Tapatalk
Click to expand...
Click to collapse
Tried many cables, ports and PCs.
I also tried to clean the port with a wooden stick without luck.
At this point i believe it's the usbC port or the motherboard.
I think something at the USB MTP level went faulty, because charge works fine (dash charge too).
I just can't transfer files anymore. Not even with an OTG dongle.
Since there is no other way to trasnfer the ROM zip (network is not available inside TWRP) I requested an RMA and tomorrow OnePlus send a carrier to pick it up for repair.
I have not still updated the device. I am on custom ROM. After reading your problem I am scared to install it on my device.
I think it is better to go to stock completely with locked bootloader with 5.0.8 and then accept update. After that, I can unlock the bootloader and root the device.
i just recently had this problem dude, not even 20 mins ago, find and use a diffrent usb cable/port or if u have a usb hub use that along with ur new cable, it finally worked after hours of countless tries
sandeep_kumar said:
I have not still updated the device. I am on custom ROM. After reading your problem I am scared to install it on my device.
I think it is better to go to stock completely with locked bootloader with 5.0.8 and then accept update. After that, I can unlock the bootloader and root the device.
Click to expand...
Click to collapse
Don't worry, if the USB port is working you can always recover. Just be sure your PC recognize the device first, in case anything happens.
cmurder61 said:
i just recently had this problem dude, not even 20 mins ago, find and use a diffrent usb cable/port or if u have a usb hub use that along with ur new cable, it finally worked after hours of countless tries
Click to expand...
Click to collapse
I've been trying for the whole day with 5 different cables, 4 different PC and every usb port of them. I just didn't try with an hub because i don't have one, but i don't think it makes any difference. Anyway the phone i ready to be send for repair now.
if that's ur lat hope, go for it, but the specific cable i used was a belkin usb cable from walmart, u should also update ur adb drivers, if i could id let u use my pc lol
cmurder61 said:
if that's ur lat hope, go for it, but the specific cable i used was a belkin usb cable from walmart, u should also update ur adb drivers, if i could id let u use my pc lol
Click to expand...
Click to collapse
Nah its not the cable or drivers, I test roms every 1/2 months and always been fine with uploading files with adb, fastboot or MTP. Nothing changed. Must be some hardware issue.
Oneplus already sent me the shipment code and i'm waiting for UPS to pick up the package today.
matrixino said:
Nah its not the cable or drivers, I test roms every 1/2 months and always been fine with uploading files with adb, fastboot or MTP. Nothing changed. Must be some hardware issue.
Oneplus already sent me the shipment code and i'm waiting for UPS to pick up the package today.
Click to expand...
Click to collapse
i see, well good luck to ya
I have a OnePlus 8 Pro running Oxygen OS 11.0.4.4.IN11AA. Upon installing Magisk, I can no longer turn Wifi on. I have tried restarting, clearing the cache from recovery, resetting network settings, basically all the things the "wifi wont turn on help pls" guides say to do. Mobile data and bluetooth work absolutely fine, so what's going on?
Sound is also non-functional. Even after plugging in earphones (which worked with this phone previously) nothing comes out, and the phone doesn't even seem to recognize them. I also noticed that after a reboot the volume controls are set back to the defaults.
Additionally, the system is very slow to start up and the screen stays black until after the unlock prompt (which displays over the black screen) and then the wallpaper and everything else loads. (after which the device is responsive as normal)
These problems occurred even without installing any modules or otherwise modifying the device. I'm using the latest version of Magisk, 22.0 (22000).
I originally tried to make a GitHub issue, but it was closed by the bot since I didn't follow the template GitHub never showed me. Also, us non-canary users experience issues too. [mini-rant over]
Sorry if this is a duplicate, the search system appears to be malfunctioning since the updates.
The Fix!
Looks like I'm solving all my problems today. I had a hunch that the culprit was the boot.img which I downloaded--it was corrupt. So I went to OnePlus' site and downloaded the OTA package, extracted the boot.img from that, and flashed it through fastboot. When I rebooted, I was greeted with the beautiful almost old-IOS charging sound, and Wifi!! That boot was quite speedy too!
Hi could you explain how did you reboot your phone i have totally same problem...i tried msm download tool but i cant get my device to show there....could you please tell me how did you put OTA package into phone ? thx
FIXED!
in the end I was able to use MSM Download tool....i just had to manually download Qualcomm drivers so that my phone can be recognized. After that MSM worked and rebooted my phone totally clean. Gosh not gonna root for a while now XD
PS: More fun is that my Windows PC wasn't connected to internet so i had to download everything on my macbook and through USB stick I was bringing all app to Windows.....longest 6 hours of my life
Jaywinik said:
Hi could you explain how did you reboot your phone i have totally same problem...i tried msm download tool but i cant get my device to show there....could you please tell me how did you put OTA package into phone ? thx
Click to expand...
Click to collapse
From fastboot, use the volume keys to select Power Off and then press the power button once. Make sure the phone is unplugged while doing this. Then, with the MSM tool ready on your computer, hold down both buttons on your phone and plug in the cable from the phone to the computer. It should automatically boot into EDL mode, and MSM should say Connected.
My
Jaywinik said:
Hi could you explain how did you reboot your phone i have totally same problem...i tried msm download tool but i cant get my device to show there....could you please tell me how did you put OTA package into phone ? thx
FIXED!
in the end I was able to use MSM Download tool....i just had to manually download Qualcomm drivers so that my phone can be recognized. After that MSM worked and rebooted my phone totally clean. Gosh not gonna root for a while now XD
PS: More fun is that my Windows PC wasn't connected to internet so i had to download everything on my macbook and through USB stick I was bringing all app to Windows.....longest 6 hours of my life
Click to expand...
Click to collapse
When I had to do this I didn't connect the device to the network since I don't trust Windows 10 not to open a billion ports up and use my infrastructure for Microsoft's business. Copying to and from a crappy 2.0 drive sucks!