Hello, everyone!
I hope anyone can help me.
Yesterday I assisted with rooting and flashing a Mi 9 T Pro with Xiaomi.eu firmware.
Here are the steps which were done:
1. Unlocking bootloader via MiFlash Tool.
2. Flashing TWRP (this one: https://androidfilehost.com/?fid=6006931924117906979)
3. First trouble: It only booted once into TWRP with "fastboot boot recovery xxx.img, after formatting data and a restart of TWRP it refused to get access again, neither with a command nor with hardware keys. It was stuck in fastboot.
4. With the MiFlash Tool I reverted to the stock global (this one: http://bigota.d.miui.com/V10.3.1.0....M_20190805.0000.00_9.0_global_135788d537.tgz)
5. After successfully flashing the stock ROM, I downloaded and flashed this TWRP: https://www.androidfilehost.com/?fid=1899786940962577905
6. Flashing this version of TWRP went perfectly fine.
7. In TWRP I formatted data again. I restarted TWRP and copied the following files to storage:
ROM: https://androidfilehost.com/?fid=1899786940962578113
Magisk 19.2.zip
Disable_dm verity_ForceEncrypt
8. I wiped Dalvik, cache, system and data.
9. I flashed ROM - it went through without problems
10. I tried to flash the dm verity, then an error occurred (please see the attached picture).
Can you please tell me what I'm doing wrong? Root is mandatory for me, I definitely need it.
I'm looking forward to your input and your help, it's very appreciated!
try to unmount system then flash it again
SkipperRyujin said:
try to unmount system then flash it again
Click to expand...
Click to collapse
Thanks for your input. I tried that, unfortunately this didn't work.
But I found the solution a few minutes ago:
I downloaded TWRP 3.3.1-13 (one version newer) and flashed it inside of my old TWRP. I rebooted to recovery again and then flashed Magisk without problems.
(The dm verity still refuses to install but the phone is booting and running.)
Well, it always work for me, or simply reboot recovery also work. Try wzsx twrp, it has remove DM verity & forced encryption remover in advanced menu
Hi all,
I was on xiaomi.eu MIUI 11 ROM for some time, but wanted to switch to either Evolution or Syberia ROM.
I did a complete wipe and installed evolution os trough twrp... but i forgot to remove encryption so i bricked my device...
So then, I flashed the latest stock rom (11.05)with Xiaomi flash tool, but then i was stuck with the chinese ROM so...
1. I went back to bootloader and flashed mauronofrio's TWRP recovery .
2. completely wiped phone; Cache,System,Data,Internal storage
3. copied Evolution OS 4.1 to my phone
4. installed zip trough TWRP, all successfull
5. but then when rebooting, TWRP says:"No OS installed, do you wish to continue"
6. i tried other ROMs like xiaomi.eu and syberia, but these would either give me the same problem, or just bootloop until iam back in the fastboot screen...
Anyone any idea what iam doing wrong?
dev-DaT said:
Hi all,
I was on xiaomi.eu MIUI 11 ROM for some time, but wanted to switch to either Evolution or Syberia ROM.
I did a complete wipe and installed evolution os trough twrp... but i forgot to remove encryption so i bricked my device...
So then, I flashed the latest stock rom (11.05)with Xiaomi flash tool, but then i was stuck with the chinese ROM so...
1. I went back to bootloader and flashed mauronofrio's TWRP recovery .
2. completely wiped phone; Cache,System,Data,Internal storage
3. copied Evolution OS 4.1 to my phone
4. installed zip trough TWRP, all successfull
5. but then when rebooting, TWRP says:"No OS installed, do you wish to continue"
6. i tried other ROMs like xiaomi.eu and syberia, but these would either give me the same problem, or just bootloop until iam back in the fastboot screen...
Anyone any idea what iam doing wrong?
Click to expand...
Click to collapse
This works for me every time.
1 Flash the latest fastboot ROM.
2 Flash TWRP (same one you used)
3 Boot into TWRP (use the vol+ button when booting)
4 In format menu swipe to factory reset, then format data (VERY IMPORTANT this must be FORMAT not just wipe)
5 In reboot menu boot into recovery, this ensures TWRP correctly accesses the newly formatted data partition.
6 Copy over the ROM (and GApps, if needed and/or Magisk)
7 Flash the ROM, (then GApps if needed)
8 Boot into system and do the initial setup
9 If installing Magisk, boot back to TWRP and install Magisk.
There is no need to wipe anything else. There is no need to wipe anything again after installing. There is no need to disable encryption or dm-verity.
Robbo.5000 said:
This works for me every time.
1 Flash the latest fastboot ROM.
2 Flash TWRP (same one you used)
3 Boot into TWRP (use the vol+ button when booting)
4 In format menu swipe to factory reset, then format data (VERY IMPORTANT this must be FORMAT not just wipe)
5 In reboot menu boot into recovery, this ensures TWRP correctly accesses the newly formatted data partition.
6 Copy over the ROM (and GApps, if needed and/or Magisk)
7 Flash the ROM, (then GApps if needed)
8 Boot into system and do the initial setup
9 If installing Magisk, boot back to TWRP and install Magisk.
There is no need to wipe anything else. There is no need to wipe anything again after installing. There is no need to disable encryption or dm-verity.
Click to expand...
Click to collapse
thanks, i always thought that a wipe was sufficient, or at least equal to a format... anyways will report back later when i have time to try it. lets hope it works because i can't handle this chinese rom
dev-DaT said:
thanks, i always thought that a wipe was sufficient, or at least equal to a format... anyways will report back later when i have time to try it. lets hope it works because i can't handle this chinese rom
Click to expand...
Click to collapse
The format is needed to temporarily remove encryption
I've just remembered that I missed an important step. Call it step 1.5
If you going to flash immediately after flashing official MIUI you must boot into MIUI once before doing anything else. You don't need to go through the set-up, you can boot immediately into fastboot after you get to the initial set-up page. The first boot finalises the install and is needed before you flash over the top of it. That may be the cause of your issue if you had missed this before.
Robbo.5000 said:
The format is needed to temporarily remove encryption
I've just remembered that I missed an important step. Call it step 1.5
If you going to flash immediately after flashing official MIUI you must boot into MIUI once before doing anything else. You don't need to go through the set-up, you can boot immediately into fastboot after you get to the initial set-up page. The first boot finalises the install and is needed before you flash over the top of it. That may be the cause of your issue if you had missed this before.
Click to expand...
Click to collapse
Ok so i flashed TWRP again, rebooted to stock rom and then rebooted into recovery, but the stock recovery is still there.
When i flash TWRP and reboot into recovery immediately i can enter TWRP, but if i reboot the phone to MIUI and then reboot again, TWRP is gone again...
It seems like TWRP does not persist... now iam stuck again on fastboot screen because i wiped + formatted everything.
Edit:
When i want to flash recovery it says "OKAY" but it is unable to boot:
Sending 'recovery' (65536 KB) OKAY [ 1.562s]
Writing 'recovery' OKAY [ 0.333s]
Finished. Total time: 1.989s
Sending 'boot.img' (65536 KB) OKAY [ 1.547s]
Booting FAILED (remote: 'Failed to load/authenticate boot image: Load Error')
fastboot: error: Command failed
dev-DaT said:
Ok so i flashed TWRP again, rebooted to stock rom and then rebooted into recovery, but the stock recovery is still there.
When i flash TWRP and reboot into recovery immediately i can enter TWRP, but if i reboot the phone to MIUI and then reboot again, TWRP is gone again...
It seems like TWRP does not persist... If i wipe all data trough TWRP and then reboot, i don't have OS but i do reboot back into TWRP, because well, there is nothing else...
Click to expand...
Click to collapse
This is normal, MIUI will restore stock recovery of the recovery partition changes. In order to persist TWRP you need to either install Magisk, disable dm-verity or install a custom ROM.
If you are going to flash a custom ROM, then you should do so immediately after flashing TWRP.
After formatting data, TWRP has an issue seeing the data partition, so go to the reboot menu in TWRP and select to reboot to recovery.
Then you can immediately install the ROM of choice. You cannot boot back into system as you'll lose TWRP.
Robbo.5000 said:
This is normal, MIUI will restore stock recovery of the recovery partition changes. In order to persist TWRP you need to either install Magisk, disable dm-verity or install a custom ROM.
If you are going to flash a custom ROM, then you should do so immediately after flashing TWRP.
After formatting data, TWRP has an issue seeing the data partition, so go to the reboot menu in TWRP and select to reboot to recovery.
Then you can immediately install the ROM of choice. You cannot boot back into system as you'll lose TWRP.
Click to expand...
Click to collapse
Ok, it appears that everytime i wipe system, i am not able to boot anymore into TWRP... Am i supposed to wipe System? or only wipe data & format data
dev-DaT said:
Ok, it appears that everytime i wipe system, i am not able to boot anymore into TWRP... Am i supposed to wipe System? or only wipe data & format data
Click to expand...
Click to collapse
There is no need to wipe system. You only need to wipe cache and dalvik and format data. (I choose to factory reset because it's easier in TWRP, but you could do advanced wipe and select cache and dalvik, then format data. Follow the steps exactly, but include my later step 1.5
I've just followed this myself today, as I've moved from LOS to the latest unofficial Havoc build.
In theory you could start by booting to fastboot and flashing TWRP again, then follow the steps from that point. You probably don't need to install MIUI.
Robbo.5000 said:
There is no need to wipe system. You only need to wipe cache and dalvik and format data. (I choose to factory reset because it's easier in TWRP, but you could do advanced wipe and select cache and dalvik, then format data. Follow the steps exactly, but include my later step 1.5
I've just followed this myself today, as I've moved from LOS to the latest unofficial Havoc build.
In theory you could start by booting to fastboot and flashing TWRP again, then follow the steps from that point. You probably don't need to install MIUI.
Click to expand...
Click to collapse
Ok thanks a lot! So no need to wipe system partition after stock rom install. just wipe cache/dalvik/data, got it.
Most ROM install guides tell you to wipe /system when coming from stock rom. I guess this requirement has changed? or depends on what ROM you're coming from?
Use can use my guide
https://forum.xda-developers.com/k20-pro/how-to/simple-beginners-guide-to-raphaelin-t4020543
it has how to flash roms, and fastboot fix. (which tells why the Recovery isn't staying)
Robbo.5000 said:
This works for me every time.
1 Flash the latest fastboot ROM.
2 Flash TWRP (same one you used)
3 Boot into TWRP (use the vol+ button when booting)
4 In format menu swipe to factory reset, then format data (VERY IMPORTANT this must be FORMAT not just wipe)
5 In reboot menu boot into recovery, this ensures TWRP correctly accesses the newly formatted data partition.
6 Copy over the ROM (and GApps, if needed and/or Magisk)
7 Flash the ROM, (then GApps if needed)
8 Boot into system and do the initial setup
9 If installing Magisk, boot back to TWRP and install Magisk.
There is no need to wipe anything else. There is no need to wipe anything again after installing. There is no need to disable encryption or dm-verity.
Click to expand...
Click to collapse
I need help... The reason why I'm flashing custom rom is, when the latest update came MIUI 12.5 android 11, all sensors of my phone stopped working like (Gyroscope, accelerometer, proximity sensor) I tied to flash the rom by fastboot method but still the problem persists. because of that I unlocked bootloader and flashed twrp. After flashing custom rom when I tried to boot it, it stuck on booting screen and when I tried to reboot into recovey it is showing fastboot mode. I'm unable to boot into custom rom.
dev-DaT said:
Hi all,
I was on xiaomi.eu MIUI 11 ROM for some time, but wanted to switch to either Evolution or Syberia ROM.
I did a complete wipe and installed evolution os trough twrp... but i forgot to remove encryption so i bricked my device...
So then, I flashed the latest stock rom (11.05)with Xiaomi flash tool, but then i was stuck with the chinese ROM so...
1. I went back to bootloader and flashed mauronofrio's TWRP recovery .
2. completely wiped phone; Cache,System,Data,Internal storage
3. copied Evolution OS 4.1 to my phone
4. installed zip trough TWRP, all successfull
5. but then when rebooting, TWRP says:"No OS installed, do you wish to continue"
6. i tried other ROMs like xiaomi.eu and syberia, but these would either give me the same problem, or just bootloop until iam back in the fastboot screen...
Anyone any idea what iam doing wrong?
Click to expand...
Click to collapse
Bro I have one doubt, I installed pixel os successfully then I roll back into stock os(miui) with locking bootloader, the. Again I unlock bootloader successfully, but the problem is I am unable to install os, i tried wipe data, catch. But the stock rom was not removed. What can I do?
Using orange fox in resmi note 10 pro
Hi there,
I've been rooting phones since Android 2, but lately it has been quite a challenge.
What I did so far:
Unpack new Xiaomi MI A2 (jasmine) device
Enabled Developer, USB debugging, OEM unlock in Android settings
Code:
fastboot oem unlock
Code:
fastboot flash boot_b TWRP-3.2.3-jasmine-20180804.img
TWRP ran fine. However, started with boot_a again.
OTA updated (about 6 times) to the newest version (Android 10, QKQ1.190910.002 V11.0.12.0.QDIMIXM)
Code:
fastboot flash boot_b twrp-3.4.0-0-jasmine_sprout.img
TWRP started only to the splash screen (showing "teamwin" and "Recovery Project 3.4.0-0"). Why is TWRP not starting properly?
Downloaded the stock fastboot image V11.0.12.0.QDIMIXM from https ://xiaomifirmwareupdater.com/archive/miui/jasmine/ and flash the stock boot.img via
Code:
fastboot flash boot_b jasmine_global_images_V11.0.12.0.QDIMIXM_10.0/images/boot.img
(my goal is to later patch it with Magisk and then install the patched version). However, the stock boot.img just hangs forever on the androidone screen. Why is the stock boot.img not starting properly?
I haven't used the Mi Unlock app and I didn't do an "fastboot flashing unlock_critical" yet. Is this necessary? What do I have to do to make the boot images work?
floydsen said:
Hi there,
I've been rooting phones since Android 2, but lately it has been quite a challenge.
What I did so far:
Unpack new Xiaomi MI A2 (jasmine) device
Enabled Developer, USB debugging, OEM unlock in Android settings
TWRP ran fine. However, started with boot_a again.
OTA updated (about 6 times) to the newest version (Android 10, QKQ1.190910.002 V11.0.12.0.QDIMIXM)
TWRP started only to the splash screen (showing "teamwin" and "Recovery Project 3.4.0-0"). Why is TWRP not starting properly?
Downloaded the stock fastboot image V11.0.12.0.QDIMIXM from https ://xiaomifirmwareupdater.com/archive/miui/jasmine/ and flash the stock boot.img via (my goal is to later patch it with Magisk and then install the patched version). However, the stock boot.img just hangs forever on the androidone screen. Why is the stock boot.img not starting properly?
I haven't used the Mi Unlock app and I didn't do an "fastboot flashing unlock_critical" yet. Is this necessary? What do I have to do to make the boot images work?
Click to expand...
Click to collapse
why do you feel you must use boot images ...the tried and working method for "jasmine" is to boot custom recovery and then flash magisk zip ( root only ) ..or...flash custom recovery installer zip which will flash recovery to both a/b slots.. then flash magisk
to properly boot you need to overcome stuff like secure boot and force encryption
if you aren't planning on custom roms just boot twrp to flash magisk
or
flash installer zip for recovery and wipe everything including formatting data to remove encryption and boot directly to recovery to install custom rom
twrp custom recovery had problems with decryption on stock rom ...secure boot won't allow booting modified images ..
lastly remember on jasmine there is no recovery partition..so everything is in the boot image ..magisk and recovery ..so everytime you flash stock , stock boot overwrites these changes and should flash everything again
tbh that's why i converted to wayne to get old partition layout as the A/B story pissed me off
KevMetal said:
why do you feel you must use boot images ...the tried and working method for "jasmine" is to boot custom recovery and then flash magisk zip ( root only ) ..or...flash custom recovery installer zip which will flash recovery to both a/b slots.. then flash magisk
to properly boot you need to overcome stuff like secure boot and force encryption
if you aren't planning on custom roms just boot twrp to flash magisk
or
flash installer zip for recovery and wipe everything including formatting data to remove encryption and boot directly to recovery to install custom rom
twrp custom recovery had problems with decryption on stock rom ...secure boot won't allow booting modified images ..
lastly remember on jasmine there is no recovery partition..so everything is in the boot image ..magisk and recovery ..so everytime you flash stock , stock boot overwrites these changes and should flash everything again
tbh that's why i converted to wayne to get old partition layout as the A/B story pissed me off
Click to expand...
Click to collapse
Ok. So I'm back to Stock image jasmine_global_images_V11.0.12.0.QDIMIXM_10.0 by executing "flash_all.sh". You are saying I should "simply boot". You mean:
Code:
fastboot boot TWRP-3.4.0-0-jasmine_sprout-for_V11.0.12.0.img
right? That doesn't work, it won't boot. How do I overcome secure boot and force encryption?
floydsen said:
Ok. So I'm back to Stock image jasmine_global_images_V11.0.12.0.QDIMIXM_10.0 by executing "flash_all.sh". You are saying I should "simply boot". You mean:
right? That doesn't work, it won't boot. How do I overcome secure boot and force encryption?
Click to expand...
Click to collapse
yes im saying that but post a pic of the error ...why or how doesn't it boot ..
if it is the official twrp just dump it and look for the unofficial Russian one or one modified by Nebrassy or use Orange fox and or Pitch black ..official is broken last time i checked
also the name of that looks like one hell of a job ..shorten it to
recovery.img or twrp.img
fastboot boot recovery.img
but first run
fastboot getvar all
& also run fastboot flashing unlock_critical
but most importantly get another recovery
& i don't want to insult your intelligence but after flashing stock did you check to make sure bootloader was still unlocked and that dev settings was activated and that adb was toggled to on and that you authorised adb again
basicall after stock boot device and do the above ..plug in usb ..toggle adb ..authorise ..run adb devices ..if you see your device ..adb reboot bootloader ..fastboot devices ..see your device ..fastboot getvar all ..see bootloader is unlocked ..fastboot flashing unlock_critical if not done yet ...make sure to do ALL the above again after data gets wiped.....put twrp in adb folder ( MUST BE UNOFFICIAL RUSSIAN OR MODUFIED BY NEBRASSY ..rename to revovery.img ...fastboot boot recovery.img .. use file manager to put magisk.zip on internal then flash ..then reboot to rooted phone with stock recovery ...
Sent from my wayne using XDA Labs
KevMetal said:
why do you feel you must use boot images ...the tried and working method for "jasmine" is to boot custom recovery and then flash magisk zip ( root only ) ..or...flash custom recovery installer zip which will flash recovery to both a/b slots.. then flash magisk
to properly boot you need to overcome stuff like secure boot and force encryption
if you aren't planning on custom roms just boot twrp to flash magisk
or
flash installer zip for recovery and wipe everything including formatting data to remove encryption and boot directly to recovery to install custom rom
twrp custom recovery had problems with decryption on stock rom ...secure boot won't allow booting modified images ..
lastly remember on jasmine there is no recovery partition..so everything is in the boot image ..magisk and recovery ..so everytime you flash stock , stock boot overwrites these changes and should flash everything again
tbh that's why i converted to wayne to get old partition layout as the A/B story pissed me off
Click to expand...
Click to collapse
KevMetal said:
yes im saying that but post a pic of the error ...why or how doesn't it boot ..
if it is the official twrp just dump it and look for the unofficial Russian one or one modified by Nebrassy or use Orange fox and or Pitch black ..official is broken last time i checked
Sent from my wayne using XDA Labs
Click to expand...
Click to collapse
Of course it is the official one. OMFG twrp-3.4.0-0-jasmine_sprout.img is broken (freezes on the TWRP splash screen), but version 3.3.1 seems to work. That's a relief, so I will try to flash magisk now. Although, I think I will need to do the decryption thing for jasmine first, but I guess I'll follow https://www.the***********.com/install-twrp-recovery-root-xiaomi-mi-a2-a2-lite/ mostly
floydsen said:
Of course it is the official one. OMFG twrp-3.4.0-0-jasmine_sprout.img is broken (freezes on the TWRP splash screen), but version 3.3.1 seems to work. That's a relief, so I will try to flash magisk now. Although, I think I will need to do the decryption thing for jasmine first, but I guess I'll follow https://www.the***********.com/install-twrp-recovery-root-xiaomi-mi-a2-a2-lite/ mostly
Click to expand...
Click to collapse
jajaja well now you know ...be careful ...some "official" roms are also more buggy than unofficial ones for Jasmine/Wayne..
LOS is an example ..so be forewarned .. if you like android 1 i guess stock rooted is a smart option to keep updates and keep device certified for google stuffs . .
alternativeky go FULL custom rom because stock and custom recovery is just a pain and not worth the hassle on an A/B treble device flashable by fastboot ..just boot the recovery when if ever needed
fyi ..you can flash magisk and it will boot ...if you don't try changing the recovery ..so you can have stock rooted with magisk without rcustom recovery...* recommended by me if you only wamt stock with root
Sent from my wayne using XDA Labs
All good now, thanks for your help! I just flashed Magisk (and also TWRP) and everything works nicely! I will need to get some experience, but I'll keep in mind that I maybe want to get rid of the TWRP recovery. Finally security testing is fun again. Thx!
Hi,
I have C11 RMX2185, unlocked bootloader, installed TWRP and then some roms (pixel experience, next stock android 11, next CipherOS-2.0-KNIGHT)
everything worked fine and I was preparing to try some other ROMS
But now I am unable to enter TWRP (I was, I flashed roms with TWRP before)
In fastboot I do fastboot reboot recovery and TWRP started to load (blue TWRP logo), and it blink and logo, blink - logo,.... forever
I tried to flash boot.img, flash TWRP again, tried another release of TWRP for RMX2185, flashing vbmeta, format userdata, ..... all kind of posibilities without any error but stil unable to run TWRP
I can boot into system (CipherOS-2.0), I can do things in fastboot, when it loops in starting TWRP it is able to react to adb reboot
I run out of ideas.
Thanks in advance for some kicks in the back
Hello,
This won't work for some reason. I flash spesn_global_images_V13.0.5.0.SGKMIXM_20221020.0000.00_12.0_global with fastboot.
Then I boot TWRP with fastboot boot twrp.img. I then install xiaomi.eu_multi_HMNote11_V13.0.5.0.SGKMIXM_v13-12.zip in twrp.
But then it just keeps booting to recovery.
Did anybody try this or have tips?
Thanks.
I don't remember exactly what I did, but I think I flashed the fastboot version and then updated
Be sure to get the version of recovery for the android version you want to flash. Or that was the case back then.
Be sure to format /data as well, not just wipe
Okay, I got it working like this:
1. Flash xiaomi.eu_multi_HMNote11_V13.0.10.0.RGKMIXM_v13-11-fastboot
2. Fastboot boot into OrangeFox-R11.1_A12.1-Unofficial-spes
3. Push xiaomi.eu_multi_HMNote11_V13.0.5.0.SGKMIXM_v13-12.zip via adb to /data/
4. reboot to bootloader
5. fastboot boot into twrp-3.6.1_11-0-spes
6. install xiaomi.eu_multi_HMNote11_V13.0.5.0.SGKMIXM_v13-12.zip and format data
7. reboot
Very annoying it doesn't work by just flashing the xiaomi eu zip on anything.
Strange, I got mine working first time flashing using TWRP 3.6.1
A bit of a messy procedure is required because of several technical changes from Android 11 to Android 12.
Plus, Xiaomi's messy encryption makes things worse.
Use TWRP 3.7.0