Exynos DAC - Samsung Galaxy Note 9 Questions & Answers

Does anybody know what the audio is like on the n9. N8 was impressive. Anybody found details on the n9?
Thanks
Sent from my SM-N950F using Tapatalk

I am waiting to hear that too, I ordered mine. I had a V20 before and it was brilliant.

Probably Cirrus Logic CS47L93 as with Exynos S9. GSMArena's measurements are very promising but I take them with a grain of salt. I'm still wondering about output voltage though, as PhoneArena hasn't done the measurement for the Note 9, although it was measured at 0.75V for the S9. That should be decent enough for most consumer-level headphones but still lower than past iPhones or HTCs that had headphone jacks, or LG V-series.

FYL21 said:
Probably Cirrus Logic CS47L93 as with Exynos S9. GSMArena's measurements are very promising but I take them with a grain of salt. I'm still wondering about output voltage though, as PhoneArena hasn't done the measurement for the Note 9, although it was measured at 0.75V for the S9. That should be decent enough for most consumer-level headphones but still lower than past iPhones or HTCs that had headphone jacks, or LG V-series.
Click to expand...
Click to collapse
I am not sure about wired big headphones, but the volume from the headphone jack is pretty good on the bundles AKG's. The HTC 10 etc are something else, but I wasn't impressed with the ourput from iphones or the V series DAC's. Not enough volume.

htc10>Note9
so going from my htc10 to note 9 is a step down?
kindly do let us know.
thanks.

In my opinion, I don't think it's a step down in real audio quality to the ear on the snapdragon. The HTC doesn't perform as good as an external DAC, IMO and I don't notice a big difference on the devices. I had the same questions, being a lifelong HTC guy. But if you've got more sensitive ears than me or different audio profiles you may hear a difference.
I use the ear-studio ES-100 portable DAC and Bluetooth DAC and if you go that route, I highly recommend it.
Sent from my SM-N960U using Tapatalk

well other than audio i need a decent camera and good battery life.
htc is failing in the last department.(Battery)...

Pubbaa said:
so going from my htc10 to note 9 is a step down?
kindly do let us know.
thanks.
Click to expand...
Click to collapse
I think audio detail/clarity is pretty similar to the HTC10. The output is much weaker though. I have low impedance earphones so it's not much of a struggle. Higher impedance headphones may not achieve the same volume levels. I know GSM Arena rated the audio very highly if I remember. Not as good as the LG, but close.

well, that is my main concern, maybe it is my imagination but having the headphones pumping out music at half the maximum of the htc10 made me feel good...(i Know i'm weird)
i migrated from s6e+ to the htc10, day and night difference in audio quality between the two.
if the note9 can do better (at least better than the 10) i'd bag it. Oh Well maybe next year sammy

Like the S9, the DAC on the exynos version is probably a custom Cirrus Logic CS47L93 design and very highly regarded in the audiophile world (unlike the AqSTIC DAC in the snapdragon version).
Its almost identical pretty much to the fantastic CS43131: https://www.cirrus.com/products/cs43131/
However the DAC is only half the story. True amplification and impedance plays a big part when driving high powered earphones. But it is the audio tuning that is key. The reason why high end audio separates like Nad, Arcam and Cambridge Audio etc beat the still great quality of a SONOS is down to stellar audio engineering, crossover interference minimisation and high quality internals etc.
Samsung have actually done a decent job here. There is a difference in quality between their snapdragon and exynos (though they also tuned the Aqstic to the best if its capabilities to be fair, but the soundstage on the exynos is more apparent).

HTC 10 used Aqstic as well, but they use a Class D amp alongside it. Previously they only depended on using the integrated DACs for their SoC, usually with a Class D amp at ~1V. The Mediatek devices had a Wolfson DAC and the results were pretty comparable between them. That said, some reviewers did note that HTC's headphone output has clipping distortion at maximum volume (although it is said to be blaringly loud). I had the HTC Butterfly s before that and despite GSMArena giving it an outstanding audio, and it had this issue along with hissing. Its volume isn't particularly high either, and according to PhoneArena its output was only 0.35V, which is odd for an HTC. Also, its headphone jack wasn't very durable and got damaged when the cable got strained.
I'm still curious to see measurements from the Snapdragon Note 9 and the output voltage of the Note 9. S9/S9+ is 0.75V. I think the volume is excellent for IEMs, but for over-ear headphones it is still little low. Audio-Technica MSR7 is quite loud, but the Takstar Pro 82 and 1More MK802 still require a fair bit of volume to match it - all are 32 ohms. I also used the Sony Xperia Z5 which also had only 0.35V headphone output, but it was louder than the HTC at max volume without any bass clipping distortion. MSR7 was quite loud at maximum volume but the other two were borderline in terms of volume. The overall sound was brighter with a slight roll-off in the bass. Quite a few users complained about the DAC but I thought it wasn't too bad. I think the Note 9's is less brittle-sounding and more subtle with the treble, but still detailed. The headphone jack was also more durable than the HTC's although I've had an occasion where it temporarily failed on me and I needed to use SoundAbout to force detection (there were many complaints of such happening to Xperia phones). I'm wondering if Samsung Galaxy headphone jacks are more durable?

FYL21 said:
HTC 10 used Aqstic as well, but they use a Class D amp alongside it. Previously they only depended on using the integrated DACs for their SoC, usually with a Class D amp at ~1V. The Mediatek devices had a Wolfson DAC and the results were pretty comparable between them. That said, some reviewers did note that HTC's headphone output has clipping distortion at maximum volume (although it is said to be blaringly loud). I had the HTC Butterfly s before that and despite GSMArena giving it an outstanding audio, and it had this issue along with hissing. Its volume isn't particularly high either, and according to PhoneArena its output was only 0.35V, which is odd for an HTC. Also, its headphone jack wasn't very durable and got damaged when the cable got strained.
I'm still curious to see measurements from the Snapdragon Note 9 and the output voltage of the Note 9. S9/S9+ is 0.75V. I think the volume is excellent for IEMs, but for over-ear headphones it is still little low. Audio-Technica MSR7 is quite loud, but the Takstar Pro 82 and 1More MK802 still require a fair bit of volume to match it - all are 32 ohms. I also used the Sony Xperia Z5 which also had only 0.35V headphone output, but it was louder than the HTC at max volume without any bass clipping distortion. MSR7 was quite loud at maximum volume but the other two were borderline in terms of volume. The overall sound was brighter with a slight roll-off in the bass. Quite a few users complained about the DAC but I thought it wasn't too bad. I think the Note 9's is less brittle-sounding and more subtle with the treble, but still detailed. The headphone jack was also more durable than the HTC's although I've had an occasion where it temporarily failed on me and I needed to use SoundAbout to force detection (there were many complaints of such happening to Xperia phones). I'm wondering if Samsung Galaxy headphone jacks are more durable?
Click to expand...
Click to collapse
some good points of note here- see what i did there lol! . Also we must not forget how a more powerful headphone amp may have a hit on the battery as its essentially providing more power to the more hungry headphones available in the wilderness. The Note 9 is marketed more or less with the business user in mind. Battery priority (and we can debate til the cows come home about battery!) seems to be favouring other areas and its wired audiophile capabilities are not a main selling point...

Jonathan-H said:
I am not sure about wired big headphones, but the volume from the headphone jack is pretty good on the bundles AKG's. The HTC 10 etc are something else, but I wasn't impressed with the ourput from iphones or the V series DAC's. Not enough volume.
Click to expand...
Click to collapse
Then you should know about how to "trick" the LG phones with Quad DACs built-in into switching to their louder modes. The modes are: Normal device (lowest volume), Aux/External Device Detected (next louder), and High Impedance Mode (aka "HIM", the loudest).
How do you do this? There's a couple ways. If you want it just a LITTLE louder (Aux mode), connect the male side of a male 3.5mm to female 3.5mm adapter into the LG phone, and then connect the headphone jack into the female side of the adapter. Boom! Instant Aux mode!
Not loud enough?? lol Then buy a high impedance adapter off eBay like this one (MUST be the 75 ohm, or higher, but 75 ohm is better). This will put the phone into HIM and drive headphones up to 600 ohms. Just do the same process mentioned above for Aux.

RockStar2005 said:
Then you should know about how to "trick" the LG phones with Quad DACs built-in into switching to their louder modes. The modes are: Normal device (lowest volume), Aux/External Device Detected (next louder), and High Impedance Mode (aka "HIM", the loudest).
How do you do this? There's a couple ways. If you want it just a LITTLE louder (Aux mode), connect the male side of a male 3.5mm to female 3.5mm adapter into the LG phone, and then connect the headphone jack into the female side of the adapter. Boom! Instant Aux mode!
Not loud enough?? lol Then buy a high impedance adapter off eBay like this one (MUST be the 75 ohm, or higher, but 75 ohm is better). This will put the phone into HIM and drive headphones up to 600 ohms. Just do the same process mentioned above for Aux.
Click to expand...
Click to collapse
Adds more hardware into the signal path thus creating potential for static and getting a less clean background. I'd rather have less volume with clean signal than distortion or clipping.

@rbiter said:
Adds more hardware into the signal path thus creating potential for static and getting a less clean background. I'd rather have less volume with clean signal than distortion or clipping.
Click to expand...
Click to collapse
Potential, maybe. But I was doing the Aux method for several months on my LG V30, and I never heard ANY kind of static or distortion at all. The pros by far outweigh the cons here. Having that extra amp power strongly benefits the sound coming through your headphones.

RockStar2005 said:
Potential, maybe. But I was doing the Aux method for several months on my LG V30, and I never heard ANY kind of static or distortion at all. The pros by far outweigh the cons here. Having that extra amp power strongly benefits the sound coming through your headphones.
Click to expand...
Click to collapse
Having a low noise floor and ample headroom far outweigh potentials like static or loss of hearing because I want cannons, not speakers on my ears. Plus, I have a portable amp, JDS Labs CD5 which can make my Beyerdynamics COP or 770pro 250 ohms rattle my chest if I want to lose my hearing. ?

@rbiter said:
Having a low noise floor and ample headroom far outweigh potentials like static or loss of hearing because I want cannons, not speakers on my ears. Plus, I have a portable amp, JDS Labs CD5 which can make my Beyerdynamics COP or 770pro 250 ohms rattle my chest if I want to lose my hearing.
Click to expand...
Click to collapse
lol
That's always another option too, but the convenience that comes with only having one device should be considered too. And the V30's Quad DAC is pretty amazing. It was able to match up with my old $300 Oppo HA-2 amp/DAC device as well.
I got the DT 1770 Pro a few months ago and LOVE it too! Beyerdynamic makes some fantastic headphones!!

RockStar2005 said:
lol
That's always another option too, but the convenience that comes with only having one device should be considered too. And the V30's Quad DAC is pretty amazing. It was able to match up with my old $300 Oppo HA-2 amp/DAC device as well.
I got the DT 1770 Pro a few months ago and LOVE it too! Beyerdynamic makes some fantastic headphones!!
Click to expand...
Click to collapse
My V20 is my DAP now. Plenty of volume with built in amp. The CD5 is pretty compact. Able to rubber band it with a phone easily but I've hardly used it since the V20. Yeah. I need to get some Beyerdynamics 600ohm or open headphones. I like both of mine but want something a little more airy or different.

@rbiter said:
My V20 is my DAP now. Plenty of volume with built in amp. The CD5 is pretty compact. Able to rubber band it with a phone easily but I've hardly used it since the V20. Yeah. I need to get some Beyerdynamics 600ohm or open headphones. I like both of mine but want something a little more airy or different.
Click to expand...
Click to collapse
Yeah the volume I get from HIM is just right for me too ftw.
Yes the Quad DAC has made things a bit easier. I don't know if my next phone will be LG but if it's not I will very likely just get this bad boy........the Radsone ES100, which several ppl on Head-Fi and Amazon customer reviewers have stated sounds better than their former wired setup (with amp/DAC). I think the secret is that it has a DUAL DAC setup, and LDAC ftw. We'll see. Or else the wired Sabaj Da3, which several ppl have claimed outdoes the AudioQuest DragonFly Red. Though with the latter (Da3) I would have to carry my charger with me if I go long distance or into the city which I frequently do. lol
I've never tried any of their 600 ohm ones. I went through MANY headphones over the last 4 years to get to where I'm at now. I'm in NO hurry to upgrade anytime soon, though if I did, it would most likely be the MrSpeakers AEON Flow closed, or else Esther-C. I travel by train into the city a lot as I'd mentioned, so open-back doesn't work for me. lol

Do any of those amps have the Asahi Kasei 4458 or 4490? I would love to hear the 4490s in a phone tuned proper. I have a microprocessor with the 4458 and it is damn good. And the 4490 is better.
I wonder is Samsung peeks over Motorola's shoulder. Battery mods would actually be pretty cool for note series. An extra few mm ergonomic battery mods would serve as a good base for sketching and drawing on a tablet especially. The note9 would rock the boat with Dex and a decent 1080p projector. Stackable mod with speakers. Or Asahi Kasei 4490/4458 DAC headphone amp.
With battery mods that can easily swap batteries to recycle, make them stackable and polish Dex even more along with other endeavors. Hear me Samsung? Good hardware and software long term ideas. It will be done.
Sorry I am reading the Paris Agreement. ???

Related

What do you think of the stereo quality of P990?

Hi I've used a AKG 450 headset for a long time. The sound of it was very good if I used sony's w600 Bluetooth. If I connected it to the phone the sound wasnt to much to brag about. But now I've bought a sennheiser HD25-II-2 and a Fiio E11 but the sound through the Sony just sucks. But when I connect it directly too the phone, it sound, well, bloody f***ing good! So the situation has turned 360°. So what's wrong here? It got a great DA-converter but the phone's amp cant handle any resistance?
Amplifier, not a DA converter ;-)
I'm satisfied with sound, nothing spectacular but ok. It depends on what kind of headphones you have, higher impendance means higher load on headphone amp. Some like that, some not...
But, review on GSM arena said something about almost exceptional sound when connected to external amp so check it out
Sent from my LG-P990 using Tapatalk
No, DA -converter. It must be really good compared to its amp. The akg is a perfect 32 ohms resistance, but still it sounded very bad indeed. But with the Fiio E11 amp it sounds so good that it just (almost) doesnt make sense
I seem to remember that the highend senheisers, needs power to play well. I always go for low resistance headphones, since i only drive them with my phone amp. Sound was good with my old Sennheiser cx300 and realy good with my Sunrise Xcape Impressive edition.
That was why I bought the amp. But I had no idea that this sound was waiting to be release from the x2! All the reviews points at the stereo crossover.
I wasn't aware about theese portable amps, i might be interested if i would gain anything with my easy driven inears. I haven't taken any concern about the crossover, i don't notice it. But I guess it would still be pressent with the amp.
I've just gone through the review from gms arena and the crossover is only with headset. That confirms what I experience with an amp. Believe me, it sounds really good!
Ok normaly the Xcapes don't need an amp. But that's with ipods and sansa clip's etc. Do you think the amp in the optimus 2 x is a lot less powerfull than mp3 players normaly is. Then i should consider getting an amp maybe the Fiio e5 ?
I havent heard the E5. Its dirt cheap and I bet it sounds like it. The E11 was about 36$ from mp4 nation when I ordred it ....
Edit: from mp4 nation: )
Ok just noticed the e6. An upgrade of e5. The sound quality is said to be good. But not on par wit e11
Just one way to find out.
i find it just a meh. the bass is flat.
The bass of E11 is very tight and punchy. Guess its the way to go then.

Qualcomm DAC isn't impressive

I was using some hi-fi earphones on this phone and was getting enough power from the phone. I have DSPManager equalizer installed and I nearly had to have the volume bar full just to get decent volume. Kind of sucks, but I can't complain too much for how good the price was. Will any developers be working on this chipset?
i think chinese phone could be great and could be compare with this incredible phone
UnlockedNand said:
I was using some hi-fi earphones on this phone and was getting enough power from the phone. I have DSPManager equalizer installed and I nearly had to have the volume bar full just to get decent volume. Kind of sucks, but I can't complain too much for how good the price was. Will any developers be working on this chipset?
Click to expand...
Click to collapse
Which hi-fi earphones you are using?
With your case, I suggest you buy a headphone amp like Fiio E5 to deal with your high impedence headphones.
richteralan said:
Which hi-fi earphones you are using?
With your case, I suggest you buy a headphone amp like Fiio E5 to deal with your high impedence headphones.
Click to expand...
Click to collapse
How good are the Fiio E5's? I have been looking for something to give my 8323's a little something extra and does it work with an inline mic?
decepticon said:
How good are the Fiio E5's? I have been looking for something to give my 8323's a little something extra and does it work with an inline mic?
Click to expand...
Click to collapse
It's just a headphone amp. I haven't tried with an mic so I don't know. Don't expect too much from its price point.
But for 99% people E5 will work great. I'm using E5 with my laptop and Grado headphone.
richteralan said:
It's just a headphone amp. I haven't tried with an mic so I don't know. Don't expect too much from its price point.
But for 99% people E5 will work great. I'm using E5 with my laptop and Grado headphone.
Click to expand...
Click to collapse
Not expecting too much, just a little extra "oomph" in power to where I don't have to have the volume up to 100% and it still sound low.
decepticon said:
Not expecting too much, just a little extra "oomph" in power to where I don't have to have the volume up to 100% and it still sound low.
Click to expand...
Click to collapse
E5 can definitely do that.
I just tried connecting my Grado to N4 without the amp. And the volume is perfect for me.
Also tried connect the phone to E5 and does amplify a bit, not a lot though.
There's also an E6 for a few bucks more. The power output spec:
E5:
Output Power: 100mW (32ohms Load) 18mW (300ohms Load)
E6:
Output Power: 150mW (16Ohm), 16mW (300Ohm)
Fiio has a whole line of portable headphone amps. Check them out on Amazon.com
Thanks, I kinda like the look of the E6 more, it's less "iPod shuffle"
The E6 is a good little amp but it will only drive headphones/earphones volume-wise. If you want something that will actually make them sound better, you'll have to step it up to an E7 or an E11. I have an E17 and it's great. The bonus with the E7 and E17 is that you can plug it into your computer via USB and use it as a DAC as well as an amp without installing any drivers.
An amp will not make the source sound better. It takes the existing signal and amplifies it. If it is a poorly designed amplifier, it may even add distortion and make the signal worse. You may hear an improvement if the amplifier on the SOC can not adequately power your headphones (likely due to either high impedance or low sensitivity, or both) and you drive it into distortion. So, if this is the case then you may hear an improvement. Given some of the lack luster results from the GSMArena testing, it may be more than just the amplifier though.
Some phones with USB OTG can use mobile USB DACs, which would likely improve SQ considering the state of sound quality on mobile SOCs. They also tend to have decent quality amplifiers as well. I'm not sure we can do this with the Nexus 4 yet, but it is possible on the GS3 and I'd suspect it's only a matter of time before we get it here as well.
If you are having volume issues its almost certainly because your headphones are low impedance. Lower than the inbuilt amplifier can supply. You can easily verify by plugging in another set of crappy earphones.
As was suggested, amp is your solution or you can use one of the phones that have a more powerful amplifier. I guess some of the HTC ones may have that though I have never used them.
mesasone said:
An amp will not make the source sound better. It takes the existing signal and amplifies it. If it is a poorly designed amplifier, it may even add distortion and make the signal worse. You may hear an improvement if the amplifier on the SOC can not adequately power your headphones (likely due to either high impedance or low sensitivity, or both) and you drive it into distortion. So, if this is the case then you may hear an improvement. Given some of the lack luster results from the GSMArena testing, it may be more than just the amplifier though.
Some phones with USB OTG can use mobile USB DACs, which would likely improve SQ considering the state of sound quality on mobile SOCs. They also tend to have decent quality amplifiers as well. I'm not sure we can do this with the Nexus 4 yet, but it is possible on the GS3 and I'd suspect it's only a matter of time before we get it here as well.
Click to expand...
Click to collapse
Most USB DACs under $100 are cheaply made anyway. So there's no point to further drain your phone battery with a very minimal improvement over sound quality.
If you are really into it, use local FLAC and a small headphone amp. The best balance between mobility and audio.
sexualrug said:
You can easily verify by plugging in another set of crappy earphones.
Click to expand...
Click to collapse
The DAC in the nexus 4 drives high end IEMs easily, using hi end hifi equipment on phones and expecting it to work as Intended is bad logic
Sent from my Nexus 4 using Tapatalk 2
I found the DAC in the US SGS3 to be quite adequate for a mobile chipset, and seeing as the Nexus 4 uses the same one, I see no reason to think any differently. However, I do think the SGS3 has a more powerful amp in it. If your headphones are anywhere from 50 to 300ohm impedance, you will need an amp to get adequate volume (and sound quality) out of them. Obviously a good amp cannot make up for a poor source, but if your headphones are suffering from low power, an amp will help.
My Beyerdynamic Custom One Pros are 16ohm and I still have to turn my Nexus 4 up to ~75% volume to get them at a good listening volume. They sound great though. Obviously they sound better out of my Schiit Lyr, but my HD650s benefit more from the amount of power that bad boy puts out. I actually have to run my COPs through my E17 because the Lyr is so powerful (with a high output impedance) that it causes a low hissing on the COPs no matter the volume.
UnlockedNand said:
I was using some hi-fi earphones on this phone and was getting enough power from the phone. I have DSPManager equalizer installed and I nearly had to have the volume bar full just to get decent volume. Kind of sucks, but I can't complain too much for how good the price was. Will any developers be working on this chipset?
Click to expand...
Click to collapse
What hi-fi earphones are you using?
See the supercurio link on 11-23 in this thread.
BaronInkjet said:
See the supercurio link on 11-23 in this thread.
Click to expand...
Click to collapse
I am never a fan of RighMark Audio Analyzer from when it's written...long time ago.
But people like to compare numbers and RMAA shows some pseudo relationship between numbers and apparent audio quality.
I miss the days when you actually need to LISTEN TO THE ACTUAL DEVICE instead of staring at some numbers.
noobdeagle said:
The DAC in the nexus 4 drives high end IEMs easily, using hi end hifi equipment on phones and expecting it to work as Intended is bad logic
Sent from my Nexus 4 using Tapatalk 2
Click to expand...
Click to collapse
I don't really want to get into a discussion on what kind of differences can be heard with what kind of headphones when connected to a phone.
High-end is a very general term and doesn't really mean anything to me. If the built-in amp cannot supply enough current to the low impedance headphones, voltage (and volume) will drop. Since the OP was complaining about volume, using an external amplifier is his solution, or otherwise getting a phone that has a better built in amp. He can easily verify if the volume drop is caused by impedance by plugging in a high impedance headset and seeing if the volume reaches his desired level.
richteralan said:
I am never a fan of RighMark Audio Analyzer from when it's written...long time ago.
But people like to compare numbers and RMAA shows some pseudo relationship between numbers and apparent audio quality.
I miss the days when you actually need to LISTEN TO THE ACTUAL DEVICE instead of staring at some numbers.
Click to expand...
Click to collapse
The frequency response chart pretty much exactly described my first impression when I listened to mine.
Another thing curious is that the stats are quite different from those of the other Qualcom SoC phones (some better, some worse -- including compared to new LG with identical hardware.) I would have thought it to be near identical; most of the previous ones are in a very tight range. Perhaps the difference is due to different parties testing (Supercurio/Anandtech vs. GSMarena)?
BaronInkjet said:
The frequency response chart pretty much exactly described my first impression when I listened to mine.
Another thing curious is that the stats are quite different from those of the other Qualcom SoC phones (some better, some worse -- including compared to new LG with identical hardware.) I would have thought it to be near identical; most of the previous ones are in a very tight range. Perhaps the difference is due to different parties testing (Supercurio/Anandtech vs. GSMarena)?
Click to expand...
Click to collapse
im not sure how they test but the N4 gives some odd results, it changes alot based on the volume you set it to i believe they mention it in the anandtech review from memory, but it seems to click into different 'modes' at different volumes its kinda weird and probably software related.
wait and see what kernel devs cook up maybe.

Nexus 7 Car install questions

Ok, so I'm about to bite the bullet and get rid of my stereo and replace it with a Nexus 7. I was thinking about just getting a 1/8" phono to rca audio jack, but I see that a lot of you that are doing the install are using a USB DAC. Can someone explain to me why that is, and what the benefit is over just hooking the rca up to an amp?
Better DAC...and better preamp. The built in digital to analog for the headphones was built to a price for $200 tablet. And the analog amp for the headphones is expecting a high impedance load. Doing it through the headphones basically adds an extra analog conversion to the path (impedance matching from headphone level to rca level). An external dac bypasses this and converts directly from digital to rca level.
Sent from my Nexus 7 using xda premium
The first part is true, the DAC on the tablet is possibly a lower end one then what you'll find on an external DAC but you should spend a little time and investigate. Looking at ifix-it they don't mention an D/A converter or headphone amp. Often now it is built in to a power switching chip.
As far as the second part, the headphone amp is built to drive a low impedance (16ohms). The amp will have a high impedance (typically 500 to 1k, sometimes 10k). This is actually ideal. It maximizes the voltage your amplifier will see. And is the way amplifiers typically work.
The final thing I can say is output voltage. An external D/A might or might not drive more voltage out.
My experience is 15 years car audio installation and two degrees in electronics. I'm currently doing the same and starting a product line of items that make installing tablets better then installing aftermarket decks.
This might help
So I've been working on this for a while. Might be helpful to you!
I'm currently with a hole in my dash, Flip-flopping on n7 or n10 install. I've tested this thing with the n10, n7 and the galaxy note2 so far.
http://forum.xda-developers.com/showthread.php?p=39543101#post39543101
You can use a USB DAC with a USB Hub. The Fifo one seems to be popular at about $50.
Honestly from 15 years of car audio experience I can say that the Headphone out of the N7 sounds pretty good. I really don't know that a DAC will make any difference. I think either way you will find your self having to use Awesome beats or some other EQ app to get the sound the way you want it, but I'm thinking I'll just use the headphone out my self.

Hi-Fi Status (LG) App

In case anyone is interested, it's free for a short time. I would have posted this in the free apps thread, but it was closed.
https://play.google.com/store/apps/details?id=com.apptrio.hi_fi_status
Have no idea why, but this app break my fingerprint unlock. After uninstall everything back to normal.
Yes, downloaded it today
Dizzyrul3z said:
Have no idea why, but this app break my fingerprint unlock. After uninstall everything back to normal.
Click to expand...
Click to collapse
Try again? That doesn't happen on any of the three LG V30 I have it installed on.
Hi, just tried this but didn't recognise the standard LG headphones which are high impedance.
Looks like a novelty anyway as no actual settings in app.
Uninstalled.
gazzacbr said:
Hi, just tried this but didn't recognise the standard LG headphones which are high impedance.
Looks like a novelty anyway as no actual settings in app.
Uninstalled.
Click to expand...
Click to collapse
The standard LG headphones aren't high impedance. Sorry.
They are as they trigger the lg dac message
gazzacbr said:
They are as they trigger the lg dac message
Click to expand...
Click to collapse
But the "best" settings are reserved for High Impedance Mode.
That's why @Whiskeyomega has a mod to force HIM with root.
You normally need 50 ohms impedance to trigger high impedance mode. That's why some people bought the 75 ohms jack to mate with their less than 50 ohms headsets (75 seems the least you can buy).
https://www.aliexpress.com/item/DUN...5-ohm-For-Hi-Fi-Audio-player/32813442525.html
or you can buy headsets with 50 ohms or greater to get HIM.
Or you can use root to trigger that through @Whiskeyomega mod.
https://forum.xda-developers.com/lg-v30/themes/fix-impedance-mode-time-t3729043
Yes, as I said, the standard headphones are more than 50 ohms, that's why they trigger the dac message. They do sound better when him is set.
Manually setting the him mode with my sennheiser cx-500i, which are only 18 ohms did not help the quality.
gazzacbr said:
Hi, just tried this but didn't recognise the standard LG headphones which are high impedance.
Looks like a novelty anyway as no actual settings in app.
Uninstalled.
Click to expand...
Click to collapse
My LG headphones which came with my V30+ are NOT high impedance. Are you speaking of the "B&O" branded headphones or the "LG" branded headphones? Depends on where you buy your V30+. In North America, we got "LG" branded headphones, while other places got "B&O" branded headphones . NEITHER are 50 ohms or more and neither trigger High Impedence Mode.
So, I bought high impedance headphones and I also have the 75 ohms adapter if I need it.
Hi, I have LG branded headphones. Bought my phone in Dubai, ARE dual sim version.
My H930 came with B&O headphones and they're definitely not high impedance headphones. And if they are, they're rubbish, because when you plug in proper high impedance headphones, you feel the difference instantly.
LG went full retard here. They brag about quad DAC and then they go and cheap out on headphones. Ridiculous.
The headphones that came with my girlfriend's ancient Galaxy S4 mini sound better than these quasi premium B&O thingies.
Having said that, a cool app this.
Now a question. A friend of mine has a pair of Audio Technica m50x headphones that he wants to sell. They're not high impedance so if I decide to buy them from him I'll need to get an adapter. Besides cranking up the volume to the max, is there any other danger driving low impedance headphones with an adapter in high impedance mode?
Zoombaya said:
My H930 came with B&O headphones and they're definitely not high impedance headphones. And if they are, they're rubbish, because when you plug in proper high impedance headphones, you feel the difference instantly.
LG went full retard here. They brag about quad DAC and then they go and cheap out on headphones. Ridiculous.
The headphones that came with my girlfriend's ancient Galaxy S4 mini sound better than these quasi premium B&O thingies.
Having said that, a cool app this.
Now a question. A friend of mine has a pair of Audio Technica m50x headphones that he wants to sell. They're not high impedance so if I decide to buy them from him I'll need to get an adapter. Besides cranking up the volume to the max, is there any other danger driving low impedance headphones with an adapter in high impedance mode?
Click to expand...
Click to collapse
https://www.toa.jp/soundoh_wiki/index.php?Difference between low and high impedance speakers?
Thanks for the link. All clear now. So I guess I'll order a pair of Soundmagic 50c (or 80c), since everyone's praising them for their quality output.

USB Type-C headphones' volume is too low

Hello guys !
I am not sure if anyone has noticed (or I'd rather say, has felt annoyed) by the stock headphones or by the output produced by the regular Jack 3.5 through their Type-C to Jack converter, but I have...
Personally, I am very demanding when it comes to music, and by choosing a 850-euro phone, this possible "issue" didn't cross my mind before I bought it. It seems like listening to music on this phone, (using headphones of course) comes with pluses and minuses.
As a Pro feature, the sound is excellent, the lows and highs sound quite good actually, but (there is a big "BUT") the maximum volume is too quiet, compared to other mainstream phones on the market, using mainly Jack interface for the headphones. The maximum volume on this phone, when using headphones is about 70-75% of the maximum volume on other phones (Mi Note Pro, Samsung Galaxy series, IPhone).
I made sure "Dolby atmos" is enabled, I have even tried raising all the EQ parameters (so that the general volume may be increased), I have also tried preamp-ing the sound with apps like Poweramp or Speakerbooster, but they would only sound like forced, and not actually louder, and the result is the same.
So, my sole question is : what should I do/buy/try in order to get a LOUDER experience when using headphones ?
Thank you in advance !
P.S.: sorry if I'm being awkward, it's my first post on XDA. Cheers !
Is there a safety volume limiter on?
Sent from my CLT-L29 using Tapatalk
Robertdotnet said:
Hello guys !
I am not sure if anyone has noticed (or I'd rather say, has felt annoyed) by the stock headphones or by the output produced by the regular Jack 3.5 through their Type-C to Jack converter, but I have...
Personally, I am very demanding when it comes to music, and by choosing a 850-euro phone, this possible "issue" didn't cross my mind before I bought it. It seems like listening to music on this phone, (using headphones of course) comes with pluses and minuses.
As a Pro feature, the sound is excellent, the lows and highs sound quite good actually, but (there is a big "BUT") the maximum volume is too quiet, compared to other mainstream phones on the market, using mainly Jack interface for the headphones. The maximum volume on this phone, when using headphones is about 70-75% of the maximum volume on other phones (Mi Note Pro, Samsung Galaxy series, IPhone).
I made sure "Dolby atmos" is enabled, I have even tried raising all the EQ parameters (so that the general volume may be increased), I have also tried preamp-ing the sound with apps like Poweramp or Speakerbooster, but they would only sound like forced, and not actually louder, and the result is the same.
So, my sole question is : what should I do/buy/try in order to get a LOUDER experience when using headphones ?
Thank you in advance !
P.S.: sorry if I'm being awkward, it's my first post on XDA. Cheers !
Click to expand...
Click to collapse
Hello, I don't use high quality/impedance headphones with my P20 Pro but watch this review from about 15min 15secs in. I've not verified this but hope it helps you!
https://youtu.be/nD3j00wzcao?t=15m16s
I checked with Bose QC35 and the sound is 30% louder via Bluetooth than the jack lead....... How can this be
reply
orangecroc said:
Is there a safety volume limiter on?
Sent from my CLT-L29 using Tapatalk
Click to expand...
Click to collapse
Nope... I have checked and there's nothing like that.
Ol' Blue Eyes said:
Hello, I don't use high quality/impedance headphones with my P20 Pro but watch this review from about 15min 15secs in. I've not verified this but hope it helps you!
Thank you very much ! I think I am actually going to buy a new adapter in the near future. :highfive:
Click to expand...
Click to collapse
Just buy the Google Pixel 3.5mm USB C adapter , its the best. I also have the HTC adapter, but Google's one is better.
gavinfabl said:
Just buy the Google Pixel 3.5mm USB C adapter , its the best. I also have the HTC adapter, but Google's one is better.
Click to expand...
Click to collapse
Thank you for the reply! I will consider your advice.
gavinfabl said:
Just buy the Google Pixel 3.5mm USB C adapter , its the best. I also have the HTC adapter, but Google's one is better.
Click to expand...
Click to collapse
Link
Here you go https://store.google.com/product/usb_c_headphone_adapter
gavinfabl said:
Here you go https://store.google.com/product/usb_c_headphone_adapter
Click to expand...
Click to collapse
Thanks for the link. I found it a few hours ago, but I can't place the command, because my country is not covered by the official Google store, so I'm going to buy it from eBay
This worked a treat:
Belkertech Nylon Braided Type C to 3.5mm Audio Microphone Female
qwerty1q said:
I checked with Bose QC35 and the sound is 30% louder via Bluetooth than the jack lead....... How can this be
Click to expand...
Click to collapse
Because in wired mode the headphones are driven by the phone's amp and in Bluetooth they are driven by their own internal amp. Its why you can use wired mode even when the headphone battery is depleted.
How about any advice buying replacement earphones instead of the adapter? I'd rather just have one external thing to not lose. Are there any USB-C earphones that will do the same job as the replacement USB-C to 3.5mm for regular earphones?
Robertdotnet said:
Hello guys !
I am not sure if anyone has noticed (or I'd rather say, has felt annoyed) by the stock headphones or by the output produced by the regular Jack 3.5 through their Type-C to Jack converter, but I have...
Personally, I am very demanding when it comes to music, and by choosing a 850-euro phone, this possible "issue" didn't cross my mind before I bought it. It seems like listening to music on this phone, (using headphones of course) comes with pluses and minuses.
As a Pro feature, the sound is excellent, the lows and highs sound quite good actually, but (there is a big "BUT") the maximum volume is too quiet, compared to other mainstream phones on the market, using mainly Jack interface for the headphones. The maximum volume on this phone, when using headphones is about 70-75% of the maximum volume on other phones (Mi Note Pro, Samsung Galaxy series, IPhone).
I made sure "Dolby atmos" is enabled, I have even tried raising all the EQ parameters (so that the general volume may be increased), I have also tried preamp-ing the sound with apps like Poweramp or Speakerbooster, but they would only sound like forced, and not actually louder, and the result is the same.
So, my sole question is : what should I do/buy/try in order to get a LOUDER experience when using headphones ?
Thank you in advance !
P.S.: sorry if I'm being awkward, it's my first post on XDA. Cheers !
Click to expand...
Click to collapse
I find it as loud as my S8 plus or Pixel 2 through headphones, but BT is where it's at for volume.
fingerbob said:
How about any advice buying replacement earphones instead of the adapter? I'd rather just have one external thing to not lose. Are there any USB-C earphones that will do the same job as the replacement USB-C to 3.5mm for regular earphones?
Click to expand...
Click to collapse
I don't think I need head/earphones. I have 2 pairs of earphones (Samsung and Sennheiser), a pair of HyperX Cloud Stinger II, and studio headsets from Focusrite. I have tried all of them. And they are not the problem.
I've had many Huawei phones and 3,5mm volume has always been too low
Lähetetty minun CLT-L29 laitteesta Tapatalkilla
https://forum.xda-developers.com/huawei-p20-pro/how-to/guide-boost-headphones-volume-t3803824
If you have unlocked bootloader..
gavinfabl said:
Just buy the Google Pixel 3.5mm USB C adapter , its the best. I also have the HTC adapter, but Google's one is better.
Click to expand...
Click to collapse
In what way are these better than the HTC adapters?
Robertdotnet said:
Thanks for the link. I found it a few hours ago, but I can't place the command, because my country is not covered by the official Google store, so I'm going to buy it from eBay
Click to expand...
Click to collapse
I use the HTC dongle linked in the video above. It makes a noticeable difference. Even my cheap £15 earphones are much louder using it over the Huawei dongle.
It won't blow you away, so be realistic but it is DEFINITELY a noticeable improvement and worth the investment if you listen to music.
In fact, even my larger headphones were louder but I think you need a dac/amp to really enjoy louder volumes on large headphones. It's the cheap earphones that I found gave the loudest sound.

Categories

Resources