STORY: My TA-1004 autoupdate to Android Pie on 22Dec after I turn off my phone to charge battery.
and I follow this " https://forum.xda-developers.com/nokia-8/development/android-9-0-pie-patched-boot-img-t3875977 " to try flash "fastboot flash boot "NB-01-551-b05-Magisk-TWRP" for flash TWRP and magisk to my TA-1004 pie. and I stuck on "nokia logo" after flash, someone said "Factory reset" , I try to use "wipe>format data" in TWRP, until now, I can boot in to download mode only.
I also try this "https://forum.xda-developers.com/nokia-8/how-to/guide-restore-nokia-to-stock-t3867646 "
to restore to oreo and stuck on "Next is greyed out, click on "Edit Phone Information", you will get an error message after a while, clik on OK, BUT Next is still greyed" . Can anyone help me please?
Please check that you have the correct fastboot drivers installed. Open Windows Device manager, and check the properties of your Fastboot device. Do you see HMD Global as the manufacturer? If not, the drivers may not be correct and you should install the Nokia drivers.
singhnsk said:
Please check that you have the correct fastboot drivers installed. Open Windows Device manager, and check the properties of your Fastboot device. Do you see HMD Global as the manufacturer? If not, the drivers may not be correct and you should install the Nokia drivers.
Click to expand...
Click to collapse
thx for reply first,
I can check "Fastboot Device" in Windows Device manager , HMD Global as the manufacturer.
I can check "fastboot devices" by adb/fastboot.exe
kelvin31 said:
thx for reply first,
I can check "Fastboot Device" in Windows Device manager , HMD Global as the manufacturer.
I can check "fastboot devices" by adb/fastboot.exe
Click to expand...
Click to collapse
It should work in that case. Give a try to the NOST tool shared in the Nokia 8 forums itself.
singhnsk said:
It should work in that case. Give a try to the NOST tool shared in the Nokia 8 forums itself.
Click to expand...
Click to collapse
NOST is it means Nokia OST (Online Service Tool) latest version and I need download android pie rom first?
kelvin31 said:
NOST is it means Nokia OST (Online Service Tool) latest version and I need download android pie rom first?
Click to expand...
Click to collapse
NOST" - short for "No Service Tool"
https://forum.xda-developers.com/no...t-improved-version-ost-la-6-0-4-v0-4-t3875574
You should use the existing NB0 which you have for the Nokia 8. I think it is on Oreo only. I hope you do have it.
singhnsk said:
It should work in that case. Give a try to the NOST tool shared in the Nokia 8 forums itself.
Click to expand...
Click to collapse
singhnsk said:
NOST" - short for "No Service Tool"
https://forum.xda-developers.com/no...t-improved-version-ost-la-6-0-4-v0-4-t3875574
You should use the existing NB0 which you have for the Nokia 8. I think it is on Oreo only. I hope you do have it.
Click to expand...
Click to collapse
THx
let me study it first,
thank you very much
singhnsk said:
NOST" - short for "No Service Tool"
https://forum.xda-developers.com/no...t-improved-version-ost-la-6-0-4-v0-4-t3875574
You should use the existing NB0 which you have for the Nokia 8. I think it is on Oreo only. I hope you do have it.
Click to expand...
Click to collapse
hello, I m stuck on unlock_critical, do you have any idea?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
kelvin31 said:
hello, I m stuck on unlock_critical, do you have any idea?
Click to expand...
Click to collapse
You need to be flashing the actual unlock.bin file you used to unlock the Nokia 8. As you see in your CMD window, the command did not work out.
Make sure you're CMDing in the directory of your unlock file. Then send the command
Code:
fastboot flash unlock UnlockFile.bin
Remember to replace UnlockFile.bin with the name of actual unlock file in your PC.
singhnsk said:
You need to be flashing the actual unlock.bin file you used to unlock the Nokia 8. As you see in your CMD window, the command did not work out.
Make sure you're CMDing in the directory of your unlock file. Then send the command
Code:
fastboot flash unlock UnlockFile.bin
Remember to replace UnlockFile.bin with the name of actual unlock file in your PC.
Click to expand...
Click to collapse
unlock.bin is it provide by HMD that one?
I have receive my nokia 8 unlock bootloader file before by HMD,
name called unlock.key
is it this one? should I rename it to unlock.bin ?
thank you
kelvin31 said:
You need to be flashing the actual unlock.bin file you used to unlock the Nokia 8. As you see in your CMD window, the command did not work out.
Make sure you're CMDing in the directory of your unlock file. Then send the command
unlock.bin is it provide by HMD that one?
I have receive my nokia 8 unlock bootloader file before by HMD,
name called unlock.key
is it this one? should I rename it to unlock.bin ?
thank you
Click to expand...
Click to collapse
Yes, that's the one. You don't have to rename it. Just pass it the way you did earlier.
fastboot flash unlock unlock.key
When it gets accepted, then run:
fastboot flashing unlock_critical
singhnsk said:
Yes, that's the one. You don't have to rename it. Just pass it the way you did earlier.
fastboot flash unlock unlock.key
When it gets accepted, then run:
fastboot flashing unlock_critical
Click to expand...
Click to collapse
its work,
I need to flash unlock.key again even I unlocked my bootloader in september.
but I need flash again after auto update..
I also fastboot flashing unlock_critical, work too.
but got another problem.....
NOST tool error code: 0xa24b
ERROR= BATTERY_VOLTAGE_TOO_LOW_FAIL (0xA24B).
I can't charge or very very slow maybe.
I charge it over 1 hour still lower than NOST tool requirement(30%)...
my TA-1004 can not power off since first flash fail....
I keep saw "download mode" over light and I can't power off...
I did try volup + power, it turn off 2 sec and auto start again boot into download mode...
how can I force power off it?
thank you
kelvin31 said:
its work,
I need to flash unlock.key again even I unlocked my bootloader in september.
but I need flash again after auto update..
I also fastboot flashing unlock_critical, work too.
but got another problem.....
NOST tool error code: 0xa24b
ERROR= BATTERY_VOLTAGE_TOO_LOW_FAIL (0xA24B).
I can't charge or very very slow maybe.
I charge it over 1 hour still lower than NOST tool requirement(30%)...
my TA-1004 can not power off since first flash fail....
I keep saw "download mode" over light and I can't power off...
I did try volup + power, it turn off 2 sec and auto start again boot into download mode...
how can I force power off it?
thank you
Click to expand...
Click to collapse
You can power off the phone from the stock recovery or TWRP. That is, if you are able to boot into any of them. If you have the stock recovery file, then flash it to the phone. After that force reboot it and continue to hold the keys and it should go into recovery mode. The phone will essentially start faster in recovery mode. Or you can also choose the "Power off" option in recovery to power off the phone.
If you cannot get into recovery, then you cannot power it off. And in that case you will have to bear this slow charge only. Just plug it into a wall charger and leave it for a few hours. You can then check the battery capacity after connecting to the PC and sending the following command:
Code:
fastboot oem battery getcapacity
Start NOST and flash the phone if it is higher than the required
singhnsk said:
You can power off the phone from the stock recovery or TWRP. That is, if you are able to boot into any of them. If you have the stock recovery file, then flash it to the phone. After that force reboot it and continue to hold the keys and it should go into recovery mode. The phone will essentially start faster in recovery mode. Or you can also choose the "Power off" option in recovery to power off the phone.
If you cannot get into recovery, then you cannot power it off. And in that case you will have to bear this slow charge only. Just plug it into a wall charger and leave it for a few hours. You can then check the battery capacity after connecting to the PC and sending the following command:
Code:
fastboot oem battery getcapacity
Start NOST and flash the phone if it is higher than the required
Click to expand...
Click to collapse
THanks for help.
I charge it over 10 hrs, I did, I can flash NB1-488B Oreo 8.1 back, I can use my phone right now, thank you very much
Related
hi
my problem is
I tried to downgrade my phone
android 6 to 5
My phone was incomplete downgrade
And now when turned off and turned on
Stuck on the
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Please tell me what is the alternative
No option is not enabled
no recovery
no Emergency Updates
only fastboot mod
the fastboot mode is worked
rezaghaedamini said:
the fastboot mode is worked
Click to expand...
Click to collapse
Take it to Huawei customer service center. I lost one of my phones coz it had the same problem. Tried everything but couldn't revive it.
Took it to a shop to repair and he messed it up.
Connect to pc or laptop and open command prompt to adb folder and type fastboot devices if devices detected then we proceed http://forum.xda-developers.com/general/general/guide-flash-variant-version-firmware-t3506404.
Krish93 said:
Connect to pc or laptop and open command prompt to adb folder and type fastboot devices if devices detected then we proceed http://forum.xda-developers.com/general/general/guide-flash-variant-version-firmware-t3506404.
Click to expand...
Click to collapse
My bad, should have asked him to do this first. Mine was error 3 and wasn't revivable.
This error is different. Thanks for the help.
You need to unlock your device.
https://www.gizdev.com/install-twrp-3-0-root-honor-4x-emui-4-0/
1-unlock your device
2-run bootloader
3-install twrp
4-extract the honor firmware
http://forum.xda-developers.com/honor-4x/how-to/roll-to-emui-cm13-honor-4x-che1-l04-t3507998
5-follow the instructions as above link.
Krish93 said:
Connect to pc or laptop and open command prompt to adb folder and type fastboot devices if devices detected then we proceed http://forum.xda-developers.com/general/general/guide-flash-variant-version-firmware-t3506404.
Click to expand...
Click to collapse
i did
My phone did not change
dopserver said:
You need to unlock your device.
https://www.gizdev.com/install-twrp-3-0-root-honor-4x-emui-4-0/
1-unlock your device
2-run bootloader
3-install twrp
4-extract the honor firmware
http://forum.xda-developers.com/honor-4x/how-to/roll-to-emui-cm13-honor-4x-che1-l04-t3507998
5-follow the instructions as above link.
Click to expand...
Click to collapse
my phone is unlocked
and All these things did
Did not alter
rezaghaedamini said:
my phone is unlocked
and All these things did
Did not alter
Click to expand...
Click to collapse
Connect your phone to PC and keep device manager opened and see if device manager registers your phone.
Report back please...
muradulislam said:
Connect your phone to PC and keep device manager opened and see if device manager registers your phone.
Report back please...
Click to expand...
Click to collapse
MY English is not good please tell me What do you mean
device manager to phone
or to pc
rezaghaedamini said:
MY English is not good please tell me What do you mean
device manager to phone
or to pc
Click to expand...
Click to collapse
Keep your PC device manager open and connect your phone to PC, does it register as a new device...
not big deal ,
Do The following
Install Fastboot files .
Download TWRP .
Connect Ur Device with Fastboot ,
Flash Ur TWRP Throw Fastboot .
Boot To TWRP
FLASH STOCK img Files One By one
This Step Not Recommended but also :
Throw Fast-boot Flash UR Stock .img files .
Romiui said:
not big deal ,
Do The following
Install Fastboot files .
Download TWRP .
Connect Ur Device with Fastboot ,
Flash Ur TWRP Throw Fastboot .
Boot To TWRP
FLASH STOCK img Files One By one
This Step Not Recommended but also :
Throw Fast-boot Flash UR Stock .img files .
Click to expand...
Click to collapse
tnk not work
rezaghaedamini said:
tnk not work
Click to expand...
Click to collapse
it should otherwise there is an wrong step u did ! .
rezaghaedamini said:
tnk not work
Click to expand...
Click to collapse
If your PC does not make a sound when you connect your phone to it then you have to first install drivers.
I am sure that is the case here, your PC is not recognizing your phone.
muradulislam said:
If your PC does not make a sound when you connect your phone to it then you have to first install drivers.
I am sure that is the case here, your PC is not recognizing your phone.
Click to expand...
Click to collapse
I have installed drivers
And when I connect the phone to the sound system
Only through the Fast Boot
rezaghaedamini said:
I have installed drivers
And when I connect the phone to the sound system
Only through the Fast Boot
Click to expand...
Click to collapse
So fastboot is working... Do you have an unlocked bootloader?
Fastboot screen is simple or with red error message?
muradulislam said:
So fastboot is working... Do you have an unlocked bootloader?
Fastboot screen is simple or with red error message?
Click to expand...
Click to collapse
yes i am bootloader unlocked
Both options
Red and simple
i can Write files via Fast Boot
and write android 4 5 6
5 file
boot
system
recovery
cust
userdata
and not work
and write twrp recovery
and not work
rezaghaedamini said:
yes i am bootloader unlocked
Both options
Red and simple
i can Write files via Fast Boot
and write android 4 5 6
5 file
boot
system
recovery
cust
userdata
and not work
and write twrp recovery
and not work
Click to expand...
Click to collapse
Make a dload folder in SD card And copy update.app of the latest firmware to it.
Then, flash only recovery and boot of the latest firmware for your phone. (Extracted from update.app which you copied to SD)
After flashing above image files, type
Fastboot reboot
Quickly disconnect from pc and press and hold power + vol up + vol down until screen turns on. Let go of power but keep other two pressed for five, six sec more.
Lemme know how it works.
if stock wont work then try custom rom , install custom recovery and install custom rom .
Hello,
Yesterday i tried ton install mui 12.5.4 as i was really desappointed by the photo performance of my MI 11 Ultra compared to my Mate 40 pro, but i think that i made a mistake, as i am unable to boot it, it is stuck to Fastboot.
And i made another big mistake, i did made a dsavec of my original rom. As i bought it in France , i think that it is a european one.
1) Is there a way to now wich ROM was installed on a phone using the serial number ?
2) How can i install the EU Rom ?
a) I used the method described on this post https://forum.xda-developers.com/t/...mi-eu-rom-for-xiaomi-mi-11-pro-ultra.4260617/ buyt i am affraid that it was only for phones who had a CN rom , i realised that after flashing my phone with the fasboot method...
Please, can someone help me to identify my original ROM and to install it ?
b) I tried that method, https://c.mi.com/fr/miuidownload/detail?guide=2 but i have an error message saying that "Missmatching image and device"... Maybe at point 2) a) i because i had a EU rom and flashed with a rom working only for CN devices ?
If needed i can pay for the help.
Hoping to hear from you guys as i really need my phone on monday.
Best regards
1. I'm not sure you can easily find which ROM you had installed but it's likely to be the global version to my knowledge.
2. I would try to follow the EU ROM instructions again, making sure you follow each step correctly. Look at the post, they give 2 methods, one is using fastboot. It works with the old versions of the rom from before there was this thing called TWRP available for our device. The other method is at the bottom of the post. It's the TWRP method, that should work with the newer versions of the rom, most likely the one you downloaded.
I don't think you need to try to flash your original rom. The EU ROM is supposed to work on both variants and since you have already downloaded that, just try flashing the EU ROM until it works.
Possible mistakes would be, you didn't install TWRP and tried to install a rom that was built for it using just fastboot, maybe fastboot wasn't run as admin, maybe you didn't format correctly etc.
If you really wanna flash the stock ROM, this thread has them, with install method specified https://forum.xda-developers.com/t/miui-updates-tracker-mi-11-pro-ultra-star-mars.4263135/
Thank you for your answers, i am going to try using your last link.
Yours should be either Global or EEA if I'm not mistaken
I tried both of them and I am still stuck in fastboot mode when the phone try to reboot... I think that i really need someone to do it for me...
Do you have TWRP installed? Did you use it to flash? Maybe that would do it.
Try the fastboot version of the EU Rom. I had the same problem. Solved it for me
Do a fastboot flash (your phone is unlocked right?) Using miflash tool. Selecting "clean all" it will format everything.
Thank you guys, but the phone is still stuck on fastboot.
The phone is unlocked
I haven't TWR installed.
I am using Miflash tool, but a old version, as the latest one show error messages regarding drivers.
In Miflash, i choose "Clean All" option (and when i have an error message regarding missmatching of image and device, i delete some code in the clean all section of the rom.
I tried with many ROMS :
EEA : 2021-05-18 | Stable Fastboot | V12.5.2.0.RKAEUXM
Global : 2021-04-17 | Stable Fastboot | V12.0.2.0.RKAMIXM
I am going to try that one :
EEA :2021-05-29 | Stable Fastboot | V12.5.3.0.RKAEUXM
Pop34 said:
I am going to try that one :
EEA :2021-05-29 | Stable Fastboot | V12.5.3.0.RKAEUXM
Click to expand...
Click to collapse
Even with that last ROM the phone is still stuck in Fastboot when he automatically restart
Enter
Code:
fastboot devices
and press enter key
Then
Code:
fastboot oem device-info
and press enter key
Show the screenshot of PC command.
pl1992aw said:
Enter
Code:
fastboot devices
and press enter key
Then
Code:
fastboot oem device-info
and press enter key
Show the screenshot of PC command.
Click to expand...
Click to collapse
Where should i type that code and using which tool ?
Pop34 said:
Where should i type that code and using which tool ?
Click to expand...
Click to collapse
On PC command in the fastboot folder.
Inside the fastboot.exe folder blank space, press keyboard "shift"+mouse right click.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Choose "open command window here".
pl1992aw said:
On PC command in the fastboot folder.
Inside the fastboot.exe folder blank space, press keyboard "shift"+mouse right click.
Choose "open command window here".
Click to expand...
Click to collapse
Sorry, i opend cmd, but where can i find the "Fastboot folder" ?
Pop34 said:
Sorry, i opend cmd, but where can i find the "Fastboot folder" ?
Click to expand...
Click to collapse
You have MiFlash, so look inside the folder and find the file fastboot.exe
Ok thanks, i did it, and when i type fastboot devices, i have an error message :
Pop34 said:
Ok thanks, i did it, and when i type fastboot devices, i have an error message :
View attachment 5342883
Click to expand...
Click to collapse
No, not under power shell.
Under command.
The background should be black.
Pop34 said:
Hello,
Yesterday i tried ton install mui 12.5.4 as i was really desappointed by the photo performance of my MI 11 Ultra compared to my Mate 40 pro, but i think that i made a mistake, as i am unable to boot it, it is stuck to Fastboot.
And i made another big mistake, i did made a dsavec of my original rom. As i bought it in France , i think that it is a european one.
1) Is there a way to now wich ROM was installed on a phone using the serial number ?
2) How can i install the EU Rom ?
a) I used the method described on this post https://forum.xda-developers.com/t/...mi-eu-rom-for-xiaomi-mi-11-pro-ultra.4260617/ buyt i am affraid that it was only for phones who had a CN rom , i realised that after flashing my phone with the fasboot method...
Please, can someone help me to identify my original ROM and to install it ?
b) I tried that method, https://c.mi.com/fr/miuidownload/detail?guide=2 but i have an error message saying that "Missmatching image and device"... Maybe at point 2) a) i because i had a EU rom and flashed with a rom working only for CN devices ?
If needed i can pay for the help.
Hoping to hear from you guys as i really need my phone on monday.
Best regards
Click to expand...
Click to collapse
Mate 20 range was really ahead of it's time....
I have a mate 20 x and it's still amazing even though it launched in late 2018
Pop34 said:
Ok thanks, i did it, and when i type fastboot devices, i have an error message :
View attachment 5342883
Click to expand...
Click to collapse
Follow this guide Clean Flash custom ROMs section until step 4. (Do step 1,2, 3, 4)
Plug the phone under fastboot mode, then screenshot what it shows to you.
Pop34 said:
Ok thanks, i did it, and when i type fastboot devices, i have an error message :
View attachment 5342883
Click to expand...
Click to collapse
Or download the "info.rar", extract the "info.bat" into the folder where fastboot.exe is. Then double click that "info.bat"
Make screenshot of the command window. Need to know if your bootloader is still unlocked.
The easiest thing is just bring your phone to Xiaomi repair center and tell them to revive your phone. If you have warranty coverage, they should be able to.
Check your country Xiaomi policy for the warranty rules.
Hi, my wife gifted me that Chopin phone form China, after a wrong "flash and lock" global firmware now my phone is stuck on bootloader.
According to this thread:
Redmi Note 10 Pro 5G brick
Redmi Note 10 Pro 5G Chinese version with fastboot unlocked. After unsuccessful firmware. At startup, it goes into fastboot, you can load it into recovery. Wipe doesn't help. When trying to flash through fastboot MiFlashPro "FAILED (remote: 'not...
forum.xda-developers.com
I have all the files needed to setup sp flash and try to put again the Rom in the phone, which is now not unlocked and no usb debugging on.
Can someone please give me a tutorial on how to use those files? My phone still not recognised in sp flash com port, I don't know how to do.
If anyone will help me it will be so appreciated, thanks!
If you need to disable authorisation, did you run the MTK Auth Bypass tool and get the message "Protection disabled"? That's what I had to do before SP Flash Tool would flash the phone (without disconnecting it or rebooting), and I also had to set the baud rate to 921600, although that was all under Linux, and the phone was still unlocked.
it's complicated. with phone locked fastboot commands don't work. with my hold mi a3 fastboot flashing unlock command work. but with miui and mtk chipset probably it's useless. but u can try. if u boot into bootloader with mediatek driver the pc should recognize your phone also if it's blocked
1: Unzip this attached file into a folder. run it.
2: select the unlock bootloader and start, then connect you phone via usb with all three buttons pressed. (Phone must be off before connect, )
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3: Your bootloader will be unlocked.
4: Close the program and re-start again, this time, select auth bypass and start, then repeat the phone connection. after at the bottom line, it show bypass ok.
from here you may flash again rom via Miflash or SPflash.
P.S: I think the file size is too big, I can not attach it here. Sorry! P.M me if you wish.
Thanks for the help, the problem I'm facing it's Auth tool cont recognise the phone, when I open the shell keep saying waiting for the device.
Driver are mtk with Libus installed, dunno.
When I restart the phone immediately have the logo then, if volume up I can log mi assistant or with volume down the bootloader screen.
Bonscia said:
Thanks for the help, the problem I'm facing it's Auth tool cont recognise the phone, when I open the shell keep saying waiting for the device.
Driver are mtk with Libus installed, dunno.
When I restart the phone immediately have the logo then, if volume up I can log mi assistant or with volume down the bootloader screen.
Click to expand...
Click to collapse
1. Check your device driver for USB, suggest you re-install the MTK usb driver.
2. First run the program, select the Auth by pass then press start.
3. Make sure phone is in "power off" state, press Vol+, Vol- and power (all three at the same time), and don't release it, plug in USB cable and wait.... Don't release these three buttons until it is Auth by pass OK.
During this process, take a look at device manager, there must be one item like portable device - USB ( Com 3). keep flashing.
sure u add reinstall mtk driver
Tried many drivers, always same result:
Driver says the device can't start. Tried to install lisbus too but no changes.
Bonscia said:
Tried many drivers, always same result:
View attachment 5499127
View attachment 5499129
Driver says the device can't start. Tried to install lisbus too but no changes.
Click to expand...
Click to collapse
you "must" remove (uninstall) the driver first then re-install the MTK usb driver again.
kirinin said:
you "must" remove (uninstall) the driver first then re-install the MTK usb driver again.
Click to expand...
Click to collapse
I did that many times, with win 10 no drivers signed mode, with many different mtk drivers but nothing was working. I'll try clean my windows and then start again with the drivers.
Bonscia said:
I did that many times, with win 10 no drivers signed mode, with many different mtk drivers but nothing was working. I'll try clean my windows and then start again with the drivers.
Click to expand...
Click to collapse
is a win10 problem that i also haved. hard to solve. u can try windows 7 via virtualbox (solved a lot of my problems in the past) or format and install a modded version of win10 (but i dont suggest this)
Virtual box looks no longer available, I'll install a fresh copy of win 7 in another partition, never give up lol
virtualbox is available for all system. i have a win7 virtualized under my linux pc, and miflash works fine. no bugs. if my tips makes you happy dont try. is not my problem, i didnt bricked my phone. i dont make things without know what i'm doing. good look. u can buy a new phone if u prefere
wetito said:
virtualbox is available for all system. i have a win7 virtualized under my linux pc, and miflash works fine. no bugs. if my tips makes you happy dont try. is not my problem, i didnt bricked my phone. i dont make things without know what i'm doing. good look. u can buy a new phone if u prefere
Click to expand...
Click to collapse
? I've just told you I've tried to download virtual box for win 10 but it's not avaible now or server was temporarily down for the download, so my only way it's to set up a fresh copy on win 7 on my pc, I can't understand your hanger answer.
kirinin said:
1: Unzip this attached file into a folder. run it.
2: select the unlock bootloader and start, then connect you phone via usb with all three buttons pressed. (Phone must be off before connect, )
View attachment 5498521
3: Your bootloader will be unlocked.
4: Close the program and re-start again, this time, select auth bypass and start, then repeat the phone connection. after at the bottom line, it show bypass ok.
View attachment 5498523
from here you may flash again rom via Miflash or SPflash.
P.S: I think the file size is too big, I can not attach it here. Sorry! P.M me if you wish.
Click to expand...
Click to collapse
Hi, can you share this Zip file with link drive or mega?
Thanks in advance
Which zip file? I have only this one
https://forum.xda-developers.com/attachments/mtk_bypass_final-rar.5444529/I
finally flashed the Rom with so flash but now the phone reboot in assistance mode sayings "NV data corrupted" I'm about to cry
Hi, I've followed your instructions, I've finally flashed the Rom into the phone, but now phone bootloop into recovery, it says "nvdata is corrupted", I've took the scatter file from the Rom folder, how to fix that problem now? Thanks.
Link with files is this, I've seen other link don't work
Redmi Note 10 Pro 5G brick
Redmi Note 10 Pro 5G Chinese version with fastboot unlocked. After unsuccessful firmware. At startup, it goes into fastboot, you can load it into recovery. Wipe doesn't help. When trying to flash through fastboot MiFlashPro "FAILED (remote: 'not...
forum.xda-developers.com
Download MTK Universal Tool V5 | MediaTek All in One Tool Latest Free
MTK Universal V5 Tool is a small MediaTek All in One Tool designed to disable user locks, bypass FRP, Auth Bypass, Format Data (user data format),
www.gadgetsdr.com
Bonscia said:
Hi, I've followed your instructions, I've finally flashed the Rom into the phone, but now phone bootloop into recovery, it says "nvdata is corrupted", I've took the scatter file from the Rom folder, how to fix that problem now? Thanks.
Click to expand...
Click to collapse
try wipe data. also u can control the active slot. try change it and reboot
Hi, finally I can install the Recovery V12.5.16.0.RKPCNXM rom and the engineering rom but have no baseband and no IMEI. Tried many times to put my IMEI codes with no luck, looks I need the mt6893 modem file to use sn writer but no way to find them on net, can someone share those files please? Thanks
It is now possible to unlock bootloader using the in-depth deep testing app, however it will only work on Thailand firmware, so we are going to flash the Thailand firmware and use the in-depth app on it.
Links:
MTKClient: https://drive.google.com/file/d/13KohUUeuzVoGKxVWIuLDZx11PV8EeMBj/view?usp=sharing
SP Flash Tool: https://drive.google.com/file/d/1McZ11On8XbxGgE-hMA_nZqErHI_QwjQT/view?usp=sharing
MTK Drivers: https://drive.google.com/file/d/1UExJQxI1DmBGeDoYPul5YTXitOnsU6zx/view?usp=sharing
Thailand Firmware: https://drive.google.com/file/d/192KboBbW1eXzb6DWVlGAkGE-PEcgnHBJ/view?usp=sharing
Deep Testing APK: https://drive.google.com/file/d/1pESMmJef6Gm9YlJAE7OA_DDNnhFn3Jpz/view?usp=sharing
Libusb port filter: https://sourceforge.net/projects/li...ibusb-win32-devel-filter-1.2.6.0.exe/download
Flashing Thailand firmware:We are going to flash this in SP flash tool, first, let's setup MTK authorization bypass (if you have already setup python and drivers then skip this)
Install python from https://www.python.org/downloads/ and make sure it's configured
Go to the Driver folder, right click cdc.acm.inf and install it.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Install libusb port filter, afterwards click Next and hold volume up and down button, then choose MediaTek USB Port.
Now click install, next install UsbDK from here: https://github.com/daynix/UsbDk/releases/
Once you have done that, open a CMD/Powershell in the directory of MTKClient, write pip3 install -r requirements.txt and python mtk payload, hold the volume up and down button and plug the device in
If everything went well, you should be seeing this:
Now open SP Flash tool, go to Options > Option
Now go to Connection and select UART, set the baud rate to 921600
Now, open the scatter file (MT6785_Android_scatter.txt) from the directory of the firmware, it should load the firmware
Unselect opporeserve2 and click the Download button, it should start flashing
Once it is done flashing, you should see this:
Don't forget to reboot the device into recovery mode (volume down + power) and format data.
Updating to RealmeUI 3:Since it is not possible to use the deep testing app on RealmeUI 2, you must update to RealmeUI 3, simply update it from the update app in settings, if you do not get the update, we can't do anything about it.
No need, replaced firmware link with RealmeUI 3 Thailand firmware, just flash that and use the in-depth app in the guide!
Using the deep testing app and unlocking the bootloader:Download and install the deep testing app, tap "Apply Now" and accept the agreement, you should be seeing this now:
Wait 3 to 5 minutes, close the app and reopen again, tap "Query verification status" and you should see this:
This means your device now has unlocked fastboot access, tap "Start deep testing" and the device will reboot to fastboot mode
If you see this, the device is now in fastboot mode, to unlock the bootloader plug the device into a PC and write fastboot flashing unlock in Fastboot/ADB directory, you should see this:
Press the volume up button, the bootloader is now unlocked, congratulations!
NOTE: you can return to any EEA/Indian firmware you were on before and still have the bootloader unlocked.
Credits:
@bkerler for MTKClient
I tried this method on my primary Realme 8 device (Bangladeshi varaint) and it did worked.
Nice tutorial!
Also a pro tip for recovery mode can't be accessed after changing firmware and device keep rebooting after every 5 mins while stuck in realme bootanimation
download latest platform tools from google's official developer website, go to fastboot mode, enter command "fastboot reboot recovery"
you will be in recovery mode
then format data
your device will boot to OS after that
Does it work on realme UI 3.0 C.09 (bootloader locked)?
AJ⁰⁰⁷ said:
Does it work on realme UI 3.0 C.09 (bootloader locked)?
Click to expand...
Click to collapse
It shouldn't matter which firmware you are on right now, as for updating to TH RUI3 firmware it dosen't matter which C.0x it is as long as it's RealmeUI 3.
plarfman said:
It shouldn't matter which firmware you are on right now, as for updating to TH RUI3 firmware it dosen't matter which C.0x it is as long as it's RealmeUI 3.
Click to expand...
Click to collapse
Thank You
AJ⁰⁰⁷ said:
Does it work on realme UI 3.0 C.09 (bootloader locked)?
Click to expand...
Click to collapse
No. It's not working on RUI3 c.09 version. I've tried on my Bangladeshi 8/128 GB variant. And it got bricked after flashing the Thailand firmware.
ShahriarX1 said:
No. It's not working on RUI3 c.09 version. I've tried on my Indian 8/128 variant. And it got bricked after flashing the Thailand firmware.
Click to expand...
Click to collapse
Ohhz that's bad @plarfman
plarfman said:
It shouldn't matter which firmware you are on right now, as for updating to TH RUI3 firmware it dosen't matter which C.0x it is as long as it's RealmeUI 3.
Click to expand...
Click to collapse
I think you misunderstood it. I was asking that can I flash it over my Indian C.09 firmware?
plarfman said:
It shouldn't matter which firmware you are on right now, as for updating to TH RUI3 firmware it dosen't matter which C.0x it is as long as it's RealmeUI 3.
Click to expand...
Click to collapse
Was the Thailand firmware you attached in the post official??
Cause I got an error while flashing it. It says the firmware is not official.
ShahriarX1 said:
Was the Thailand firmware you attached in the post official??
Cause I got an error while flashing it. It says the firmware is not official.
Click to expand...
Click to collapse
Show a screenshot.
ShahriarX1 said:
No. It's not working on RUI3 c.09 version. I've tried on my Bangladeshi 8/128 GB variant. And it got bricked after flashing the Thailand firmware.
Click to expand...
Click to collapse
Stuck on recovery mode text? Then you should erase userdata, metadata and md_udc using mtkclient
And yes, mine is also Bangladeshi 8/128 varaint.
I don't know why after unlocking, entering recovery mode gets difficult. I wish that can be accessed while pressing buttons.
It's like recovery combo turns into fastboot combo
Also Oppo/Realme stock recovery has a problem when magisk is installed. It will bootloop forever when reboot to recovery from magisk and it's pretty hard to get into fastboot mode that moment.
The real fix for that problem is restore stock boot and dm-verity image
plarfman said:
Show a screenshot.
Click to expand...
Click to collapse
AE_Fahim said:
Stuck on recovery mode text? Then you should erase userdata, metadata and md_udc using mtkclient
And yes, mine is also Bangladeshi 8/128 varaint.
Click to expand...
Click to collapse
Flash is not completing bro. Have a check on the Screenshot and suggest.
ShahriarX1 said:
Flash is not completing bro. Have a check on the Screenshot and suggest.
Click to expand...
Click to collapse
Looks like your file got somehow corrupted. You can try downloading ofp file, manually decrypting it and merging multiple super.img using simg2img (super 2 must be Thailand) and setting super download is true from scatter file.
all set! I went to fastboot mode using deeptest tool. But i don't know what to do after that to unlock the bootloder device. Kindly help me!
Yadhevdev66 said:
all set! I went to fastboot mode using deeptest tool. But i don't know what to do after that to unlock the bootloder device. Kindly help me!
Click to expand...
Click to collapse
in fastboot mode enter
Code:
fastboot flashing unlock
can you send the fastboot drivers?
HELP!
I installed platform-tools_r33.0.2-windows and UniversalAdbDriverSetup, now i'm trying to flash TWRP on the XA2 Phone by using this cmd command:
adb devices
- daemon not running, starting now at xxx
adb flash recovery twrp.img
- waiting for any device
What am i doing wrong?? Please help!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Boot phone in fastboot mode
Execute "fastboot flash recovery twrp.img"
LR7875 said:
Boot phone in fastboot mode
Execute "fastboot flash recovery twrp.img"
Click to expand...
Click to collapse
How? Im pressing volume up and then connecting the phone to the pc, then i see a blue light. Is this fastboot mode? Thats what im already doing for 3 hours...
Yeah just did it again... volumeup+connect phone to pc, blue light appears on phone (fastboot mode i asume).
on pc in cmd i type adb devices, it starts the daemon.
then i type "fasboot flash recovery twrp.img"
result in cmd: "waiting for any device"
Wtf?
I swear this is so cancer can't handle this ****, the F is wrong with sony? This phone is buggy AF im trying to insall TWRP for like 4 hours now, this is a ****ing joke. What a waste of time.
Try the 15 seconds adb and fastboot driver if you haven't already
LR7875 said:
Try the 15 seconds adb and fastboot driver if you haven't already
Click to expand...
Click to collapse
This? https://forum.xda-developers.com/t/...vers-15-seconds-adb-installer-v1-4-3.2588979/
I doubt it will be any different from the platformtools adb? How could this help?
LR7875 said:
Try the 15 seconds adb and fastboot driver if you haven't already
Click to expand...
Click to collapse
You mean minimal adb ? or can you provide a link?
Connect the phone in fastboot mode (LED = blue) and open the device manager. Do you see the phone under "Other Devices" or "Android" with an exclamation mark? Then you need an ADB/bootloader interface driver. Get this for example:
https://developer.sony.com/file/download/xperia-xz2-driver/
(Yes, XZ2! There is no official XA2 driver)
Unzip it somewhere and force install the driver:
Right click on the device manager entry from above, "Update driver", "Browse my computer...", "Let me pick...", "List/show all...", "Have disk...", browse to the folder from above, open the selected .inf file and install.
Fastboot should work now. At least that's how I got it to work on a new PC.
BTW, just use "fastboot devices" to check whether it works. If your device doesn't appear, you don't need to try other fastboot commands - it won't work.
I have this problem, when installing twrp to my Sony Xperia XA2 (H3123), I am trying to install several versions of Twrp, for example: twrp-3.2.2-0-pioneer.img, twrp-3.7.0_9-0 -pioneer.img, my Sony is on Android 9
Carljaynp03 said:
I have this problem, when installing twrp to my Sony Xperia XA2 (H3123), I am trying to install several versions of Twrp, for example: twrp-3.2.2-0-pioneer.img, twrp-3.7.0_9-0 -pioneer.img, my Sony is on Android 9
Click to expand...
Click to collapse
Did you unlock the bootloader ?
Carljaynp03 said:
View attachment 5734133
Click to expand...
Click to collapse
I agree with faraway, if i remember correctly when i had this issue i didn't unlock the bootloader.
I typed a specific number in the phone dial app and it said that the bootloader is unlocked, however there is another step you need to take that i had overlooked, you need a bootloader unlock code.
The code is free, not like with chinese spyware huawai they want your money for the code...
Unlock Bootloader - Open Devices - Sony Developer World
developer.sony.com
https://developer.sony.com/develop/open-devices/get-started/unlock-bootloader/how-to-unlock-bootloader/#tutorial-step-4
and use one of these commands in cmd/adb
fastboot flashing unlock
fastboot oem unlock
Carljaynp03 said:
View attachment 5734133
Click to expand...
Click to collapse
What is your end goal? To flash a custom ROM like LineageOS? Then you can temporarily flash a recovery image to the boot partition:
fastboot flash boot <recovery_filename>.img
You don't really need TWRP for this, just use the latest official LOS Recovery:
https://download.lineageos.org/pioneer
Also see: https://wiki.lineageos.org/devices/pioneer/install
Or do you want to "permanently" install TWRP on an existing system? Then you need to directly boot into TWRP and install it from its GUI:
fastboot boot <twrp_filename>.img
See: https://twrp.me/sony/sonyxperiaxa2.html
I haven't tried the latter on the XA2 yet though and don't know how permanent that installation really is. It maybe gone after an OTA update.
irgendwer2 said:
What is your end goal? To flash a custom ROM like LineageOS? Then you can temporarily flash a recovery image to the boot partition:
fastboot flash boot <recovery_filename>.img
You don't really need TWRP for this, just use the latest official LOS Recovery:
https://download.lineageos.org/pioneer
Also see: https://wiki.lineageos.org/devices/pioneer/install
Or do you want to "permanently" install TWRP on an existing system? Then you need to directly boot into TWRP and install it from its GUI:
fastboot boot <twrp_filename>.img
See: https://twrp.me/sony/sonyxperiaxa2.html
I haven't tried the latter on the XA2 yet though and don't know how permanent that installation really is. It maybe gone after an OTA update.
Click to expand...
Click to collapse
Booting a temprary image did not work when i tried it, most likely because the bootloader wasn't unlock.
Privacydroid said:
Booting a temprary image did not work when i tried it, most likely because the bootloader wasn't unlock.
Click to expand...
Click to collapse
Independent from the bootloader status: you can't flash an image directly to the recovery partition on the XA2/Pioneer (like he tried, see screenshot) because such a dedicated partition doesn't exist on this and other A/B devices. Instead the recovery is built into the boot image.
That's why you have to use fastboot flash boot instead of recovery.
irgendwer2 said:
Independent from the bootloader status: you can't flash an image directly to the recovery partition on the XA2/Pioneer (like he tried, see screenshot) because such a dedicated partition doesn't exist on this and other A/B devices. Instead the recovery is built into the boot image.
That's why you have to use fastboot flash boot instead of recovery.
Click to expand...
Click to collapse
follow the next steps you mentioned use: fastboot flash boot recovery from LineageOS, and my phone went into a constant boot shutdown and restart, then this message appeared
and the bootloader is open
Shutdown the phone after flashing the recovery image (it doesn't seem like you did that). Then hold Volume Down + Power to boot into recovery.
irgendwer2 said:
Independent from the bootloader status: you can't flash an image directly to the recovery partition on the XA2/Pioneer (like he tried, see screenshot) because such a dedicated partition doesn't exist on this and other A/B devices. Instead the recovery is built into the boot image.
That's why you have to use fastboot flash boot instead of recovery.
Click to expand...
Click to collapse
I get that the recovery is only for a temporary boot, when i tried it, it didn't work but i can't remember what the error was.