Related
A couple of days ago my Huawei p7 started to shut itself down and after that it keeps rebooting.
It starts itself up and I get into the choose your language screen and then it shuts down.
When i try to get into the system recovery (using volume & power) I get the following screen:
Android system recovery <3e>
Huawei software installed failed.
Please retry!
Shutdown system now
There is no UPDATE.APP
.............................................
FAIL
And even in system recovery it keeps rebooting.
Im kinda helpless at the moment not knowing what to do.
Did this occur to anyone ? Is there a solution for this problem ?
Thanks in advance.
You should download firmware update file from Huawei Official web site. Extract dload folder from downloaded archive and put it on your SD card. After that you should try to trigger firmware update with factory reset (method which is usually called "force update") by holding all three buttons when the phone is turned off.
But maybe your phone have some hardware problem if it restarts even in recovery mode.
UPDATE:
Does phone restarts itself when it's in fastboot mode (you can get into that mode by holding VOLUME DOWN and POWER button while phone is turned off and connected into USB port of computer just before pressing that button combination) ??
wekii said:
You should download firmware update file from Huawei Official web site. Extract dload folder from downloaded archive and put it on your SD card. After that you should try to trigger firmware update with factory reset (method which is usually called "force update") by holding all three buttons when the phone is turned off.
But maybe your phone have some hardware problem if it restarts even in recovery mode.
UPDATE:
Does phone restarts itself when it's in fastboot mode (you can get into that mode by holding VOLUME DOWN and POWER button while phone is turned off and connected into USB port of computer just before pressing that button combination) ??
Click to expand...
Click to collapse
I've downloaded the update file and proceeded with your steps. I continued to trigger the firmware update with the factory reset.
At first it seemed to work, the phone started updating but after a couple of seconds it started to reboot itself again
I got the phone in fastboot mode and at this moment it does not restart itself !
I went on downloading Hisuite and at this moment it keeps searching for drivers on the network.
The searching for drivers is taking quite some time is this normal ?
Thank you very much for your help so far !
OK, maybe these are good news if you say that your phone doesn't restart when it's in fastboot mode.
I would recommend you to try to reflash your phone's stock recovery and boot images with those extracted from firmware that you are trying to install.
Follow these steps:
Download Huawei Extractor tool from here,
Open update.app with Huawei Extractor and extract next two images: RECOVERY and BOOT (you can do that by selecting those two images while holding CTRL button, then right click > Extract Selected),
When extracted, rename those two images into "recovery.img" and "boot.img",
Copy those two images into "platform-tools" folder of Android SDK,
Run command prompt and go to "platform-tools" folder by using "cd" command,
Start your phone into fastboot mode,
Enter following command into command prompt: "fastboot devices" (without quotes), you should get your phone's serial number listed, if that's right, go to the next step,
Enter: "fastboot oem get-bootinfo", it needs to say that your bootloader is unlocked. If it's not you need to enter the next command "fastboot oem unlock 1234567812345678", where "1234567812345678" should be replaced with unlock code that is unique for your device. Instructions which explain how to obtain unlock code for your device can be found here,
Flash your phone's recovery with "fastboot flash recovery recovery.img",
Flash your phone's boot image with: "fastboot flash boot boot.img",
After successful flashing of both images, turn your phone off by holding POWER button for a several seconds,
Prepare SD card on your PC by formatting SD card and copying "dload" folder of phone's firmware onto SD card,
After you insert SD card into phone, start your phone with "forced install" method by holding all three buttons on your phone.
After that your phone should process firmware install successfully if there is no some hardware issues. Good luck and inform us about your progress.
wekii said:
OK, maybe these are good news if you say that your phone doesn't restart when it's in fastboot mode.
I would recommend you to try to reflash your phone's stock recovery and boot images with those extracted from firmware that you are trying to install.
Follow these steps:
Download Huawei Extractor tool from here,
Open update.app with Huawei Extractor and extract next two images: RECOVERY and BOOT (you can do that by selecting those two images while holding CTRL button, then right click > Extract Selected),
When extracted, rename those two images into "recovery.img" and "boot.img",
Copy those two images into "platform-tools" folder of Android SDK,
Run command prompt and go to "platform-tools" folder by using "cd" command,
Start your phone into fastboot mode,
Enter following command into command prompt: "fastboot devices" (without quotes), you should get your phone's serial number listed, if that's right, go to the next step,
Enter: "fastboot oem get-bootinfo", it needs to say that your bootloader is unlocked, if it's not read this,
Flash your phone's recovery with "fastboot flash recovery recovery.img",
Flash your phone's boot image with: "fastboot flash boot boot.img",
After successful flashing of both images, turn your phone off by holding POWER button for a several seconds,
Prepare SD card on your PC by formatting SD card and copying "dload" folder of phone's firmware onto SD card,
After you insert SD card into phone, start your phone with "forced install" method by holding all three buttons on your phone.
After that your phone should process firmware install successfully if there is no some hardware issues. Good luck and inform us about your progress.
Click to expand...
Click to collapse
Hi,
I've got the same issue.
When I start to "force install" method, my phone doesn't boot.
It just stay in a state of "charging" but nothing append.
I flashed boot and recovery with Fastboot.
But now, when I start the phone in Fastboot&Rescue Mode, the device doesn't appear in the liste when I run adb devices.
But when I start in the "force install" mode, adb devices returns the serial of the phone (but it doesn't respond to fastboot command).
Are there other files to flash on the phone than juste recovery and boot ?
Thank's for those steps, i'll continue to try to flash again.
Edit :
Ok phone is back !
The problem came from my SD Card, I had not only the dload folder, but an other file.
Format SD Card -> dload folder -> "force install" method -> ENJOY !
Thank's a lot !
wekii said:
OK, maybe these are good news if you say that your phone doesn't restart when it's in fastboot mode.
I would recommend you to try to reflash your phone's stock recovery and boot images with those extracted from firmware that you are trying to install.
Follow these steps:
Download Huawei Extractor tool from here,
Open update.app with Huawei Extractor and extract next two images: RECOVERY and BOOT (you can do that by selecting those two images while holding CTRL button, then right click > Extract Selected),
When extracted, rename those two images into "recovery.img" and "boot.img",
Copy those two images into "platform-tools" folder of Android SDK,
Run command prompt and go to "platform-tools" folder by using "cd" command,
Start your phone into fastboot mode,
Enter following command into command prompt: "fastboot devices" (without quotes), you should get your phone's serial number listed, if that's right, go to the next step,
Enter: "fastboot oem get-bootinfo", it needs to say that your bootloader is unlocked, if it's not read this,
Flash your phone's recovery with "fastboot flash recovery recovery.img",
Flash your phone's boot image with: "fastboot flash boot boot.img",
After successful flashing of both images, turn your phone off by holding POWER button for a several seconds,
Prepare SD card on your PC by formatting SD card and copying "dload" folder of phone's firmware onto SD card,
After you insert SD card into phone, start your phone with "forced install" method by holding all three buttons on your phone.
After that your phone should process firmware install successfully if there is no some hardware issues. Good luck and inform us about your progress.
Click to expand...
Click to collapse
I followed all your steps but i get stuck at step 7. When I give the command fastboot devices it doesn't show my phone's serial number. Instead it shows a ? (question mark).
Did I do something wrong or is there a solution for this?
Thanks in advance!
Maybe you should try other version of platform tools. I would recommend you to download adt-bundle-windows-x86_64-20140702.zip (x64) or adt-bundle-windows-x86-20140702.zip (x32) from "Android SDK" official web pages (I assume that your are using Windows OS). After download extract only "platform-tools" directory to the root of Windows C:\ partition and try described procedure again.
However if you are still getting question marks instead of phone's serial number, you should ignore that step and go onto the next one. I had the same problem in the past and flash commands were successful even serial number wasn't been displayed.
Keep us informed about your progress. Good luck zbnd !!
wekii said:
Maybe you should try other version of platform tools. I would recommend you to download adt-bundle-windows-x86_64-20140702.zip (x64) or adt-bundle-windows-x86-20140702.zip (x32) from "Android SDK" official web pages (I assume that your are using Windows OS). After download extract only "platform-tools" directory to the root of Windows C:\ partition and try described procedure again.
However if you are still getting question marks instead of phone's serial number, you should ignore that step and go onto the next one. I had the same problem in the past and flash commands were successful even serial number wasn't been displayed.
Keep us informed about your progress. Good luck zbnd !!
Click to expand...
Click to collapse
Thanks for your response !
So I followed through like you said. Gave the fastboot oem get-bootinfo command and then I got (bootloader) locked. So I followed the bootloader's unlock code (official way), entered my product SN and product IMEI, used the Huawei Product ID generator followed the procedure and all I get is : Please input the correct Product ID
What did I do wrong this time ? I'm not sure if it's even possible to do this wrong. Is there another way around ?
You can unlock with Vroot, like I did. I didn't try to get a serial from Huawei.
For the Fastboot command 'Fastboot device's I had a ? too, but with 'adb devices' command, I got my serial number.
Sent from my HUAWEI P7-L10 using XDA Free mobile app
Pboguet said:
You can unlock with Vroot, like I did. I didn't try to get a serial from Huawei.
For the Fastboot command 'Fastboot device's I had a ? too, but with 'adb devices' command, I got my serial number.
Sent from my HUAWEI P7-L10 using XDA Free mobile app
Click to expand...
Click to collapse
I've downloaded Vroot (english version) but when i connect my phone it says not support mode
I tried to connect while in fastboot&rescue mode, because this is the only way the phone stays on without restarting.
I then tried to connect without fastboot&rescue mode. But my phone keeps rebooting. I did get a message that USB debugging is disabled. However I can't enable usb debugging because my phone won't boot up normally.
@Pboguet
You should read carefully because your answer has no sense for the phone which is in state like zbnd's phone is.
@zbnd
Maybe you are doing something wrong. You can send me your's phone serial number and IMEI in PM inbox, I will try to generate unlock code for you.
wekii said:
@Pboguet
You should read carefully because your answer has no sense for the phone which is in state like zbnd's phone is.
@zbnd
Maybe you are doing something wrong. You can send me your's phone serial number and IMEI in PM inbox, I will try to generate unlock code for you.
Click to expand...
Click to collapse
Thank you very much for all your help!
Despite following all your steps my phone keeps rebooting
Sorry to hear that. Did you manage to make all steps that I described to you? Can you share more informations about your current efforts please.
wekii said:
Sorry to hear that. Did you manage to make all steps that I described to you? Can you share more informations about your current efforts please.
Click to expand...
Click to collapse
Ik
After unlocking my phone I got the message unlocked in CMD.
I then flashed recovery and boot. Both times it said that the flash was succesfull, this only took a few seconds I don't know if thats normal? I then followed your last steps ( dload folder etc) and put the SD card in my phone.
It start installing but after approximetaly 25 seconds the phone shuts itself down and then reboots.
The procedure then starts again and it starts installing followed by shutting down and rebooting.
I'm sorry to hear that. Seems like it's some hardware issue.
However I still have one more idea that you can try in fastboot mode. I would recommend you to install entire firmware manually with fastboot commands.
By following previously described procedure try to extract with "Huawei Extractor" tool next images also: SYSTEM, USERDATA, CUST and CACHE.
After step number 10, try to use next commands also:
"fastboot flash system system.img"
"fastboot flash cust cust.img"
"fastboot flash userdata userdata.img"
"fastboot flash cache cache.img"
When you are finished with flashing of all images, use "fastboot reboot" command to restart your phone. Steps 11, 12 and 13 should be ignored this time.
Let me know the result
Hey, I'm glad I found this forum, because I have exactly the same problem! Since zbnd did not reply I wanted to let you know that flashing boot.img, recovery.img, cache.img, userdata.img, cust.img and system.img via fastboot did not work
The commandline for each file said "OKAY" and "finished" therefore I assume the process(es) completed succesfully.
Maybe I should tell you some information and the steps I did with my P7:
- my device is a branded german telekom version with firmware P7-L10-V100R001C150B122- because of crappy pink telekom bootlogo und bloatware I wanted to flash the original huawei firmware so I downloaded the B126 from the official website and updated via force update method- at the end of the update process i got the messages "huawei cust fail" and "update_post_process fail" but when I rebootet the B126 was installed and showed a message "Defect report reminders - This is an internal test version. Please report defects to Yangyexiao 00143718" - can't be correct, I thought- after googling a lot and reading through several forums I rooted my device with RootGenius, installed HiSuite and Android-SDK (driver were installed correctly, adb devices showed a device with serial) and deleted the "cust" directory on my phone - at that point everything still worked- next step: I installed TWRP 2.7.1.0, made an updateable zip file with huawei update extractor (including system.img, userdata.img, cust.img and boot.img) and flashed it via TWRP. The process completed succesfully, but needed only a few seconds. After that I got this bootloop at the language selection- then I wanted to return to the last functioning state, so I flashed the stock recovery via fastboot and started with force update method. But after a few seconds the device rebooted during the update process which led to another (maybe the same) bootloop. I had to remove the sd card, but the device continued to reboot in recovery mode. So i installed TWRP 2.7.1.0 again- Then I tried to restore a B133 backup I got from another forum, but it obviously did not work (see attached image)
Now I just don't know what to do ... I get a bootloop in stock recovery and I get a bootloop in TWRP 2.8.0.0.
Only TWRP 2.7.1.0 does not reboot. What is about the other files inside the UPDATE.APP (modemimage.img, efi.img, etc)? Is it possible that some of these files are needed?
Thanks in advance...
mbert said:
Hey,
Only TWRP 2.7.1.0 does not reboot.
Thanks in advance...
Click to expand...
Click to collapse
If this recovery works than try:
1. Save this Se7en or this HRT or this custom MIUI ROM on SD card
2 .Wipe in TWRP everything (dalvik, system,data,cust, internal) except external (SD card). Internal only if You have a backup or not important data there.
4. Install zipp ROM from external memory. Sometimes try more than one time in fail case. For HRT ROM especially.
Let me know if helped.
Ziółek said:
If this recovery works than try:
1. Save this Se7en or this HRT or this custom MIUI ROM on SD card
2 .Wipe in TWRP everything (dalvik, system,data,cust, internal) except external (SD card). Internal only if You have a backup or not important data there.
4. Install zipp ROM from external memory. Sometimes try more than one time in fail case. For HRT ROM especially.
Let me know if helped.
Click to expand...
Click to collapse
failed
I tried se7en and miui.
I wiped dalvik,system,data,internal,cache and custom, which only lasted about 2 seconds, but said succesful (Is that enough to delete all partitions?).
Installation of both custom roms completed succesfully and lastet several seconds (max 1 min I think).
Se7en: reboot -> huawei logo -> reboot -> language selection (in the style of stock rom?) -> reboot ...
Miui: reboot -> miui logo -> reboot -> language selection (miui style) -> reboot -> wifi selection (I skipped) -> searching for sim card -> reboot
mbert said:
Hey, I'm glad I found this forum, because I have exactly the same problem! Since zbnd did not reply I wanted to let you know that flashing boot.img, recovery.img, cache.img, userdata.img, cust.img and system.img via fastboot did not work
The commandline for each file said "OKAY" and "finished" therefore I assume the process(es) completed succesfully.
Maybe I should tell you some information and the steps I did with my P7:
- my device is a branded german telekom version with firmware P7-L10-V100R001C150B122- because of crappy pink telekom bootlogo und bloatware I wanted to flash the original huawei firmware so I downloaded the B126 from the official website and updated via force update method- at the end of the update process i got the messages "huawei cust fail" and "update_post_process fail" but when I rebootet the B126 was installed and showed a message "Defect report reminders - This is an internal test version. Please report defects to Yangyexiao 00143718" - can't be correct, I thought- after googling a lot and reading through several forums I rooted my device with RootGenius, installed HiSuite and Android-SDK (driver were installed correctly, adb devices showed a device with serial) and deleted the "cust" directory on my phone - at that point everything still worked- next step: I installed TWRP 2.7.1.0, made an updateable zip file with huawei update extractor (including system.img, userdata.img, cust.img and boot.img) and flashed it via TWRP. The process completed succesfully, but needed only a few seconds. After that I got this bootloop at the language selection- then I wanted to return to the last functioning state, so I flashed the stock recovery via fastboot and started with force update method. But after a few seconds the device rebooted during the update process which led to another (maybe the same) bootloop. I had to remove the sd card, but the device continued to reboot in recovery mode. So i installed TWRP 2.7.1.0 again- Then I tried to restore a B133 backup I got from another forum, but it obviously did not work (see attached image)
Now I just don't know what to do ... I get a bootloop in stock recovery and I get a bootloop in TWRP 2.8.0.0.
Only TWRP 2.7.1.0 does not reboot. What is about the other files inside the UPDATE.APP (modemimage.img, efi.img, etc)? Is it possible that some of these files are needed?
Thanks in advance...
Click to expand...
Click to collapse
To use fastboot you need to unlock bootloader first. And before flash, you need to erase partition first, for a proper job. Please read well about the fastboot procedure is a dangerous procedure
My bootloader is unlocked, but fastboot sais I don't have permission to erase partitions ...
Gesendet von meinem HUAWEI P6-U06 mit Tapatalk
hi,
my micromax a1 was runnning marshmallow 6.0.1 when during a security patch update installation got stuck and failed to boot again. now just booting into "dead android with exclamation mark". upon pressing power button and volume up and going into recovery(Android stock recovery) menu , cant wipe partition or data as it throws error "E: failed to mount/ cache" errors..
upon trying to install with any SD card also throws same error.
then i tried to install through ADB, while connecting to PC , PC not detecting mobile in recovery mode but detecting in bootloader mode. with fastboot flash command (for installing TWRP/CWM) in bootloader mode, error coming as "sending recovery failed(unknown status code)" .
Kindly help...
same happened to me yesterday . do you find any solution ??
Hi there !
STEP 1: DOWNLOAD the FLASH TOOL from this this link :LINK TO DOWNLOAD FILE
It is almost 30 MB in Size. And EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) of your computer.
STEP 2: DOWNLOAD LOLLIPOP FLASH FILE
DOWNLOAD LINK FOR LOLLIPOP: HERE
After downloading this flash file EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) on your computer.
STEP 3: NOW INSTALL DRIVERS:
YOU NEED TO BE ON WINDOWS 7 TO INSTALL DRIVERS (WINDOWS 8 DOESN'T SUPPORT THIS DRIVER / PHONE IS NOT DETECTED)
DOWNLOAD DRIVERS from this link : HERE
EXTRACT AND INSTALL THE DRIVERS : Next next next and finish If you see an security warning ( a red coloured pop up ) choose INSTALL IT ANYWAY
IT IS RECOMMENDED YOU TO RESTART YOUR PC.
STEP 4:
Now we have Extrated /unziped 2 files. One is FLASHTOOLS and other is FLASH FILE and Extracted it or unziped it to Desktop or Somewhere.
One of it having the name SP_Flash_Tool_exe_windows_v5.1424.00 or open both folders then one of it having the flashing tool. OPEN THE FOLDER NAMED SP_Flash_Tool_exe_windows_v5.1424.00
it contains an application named fashtool.exe OPEN IT
NOW THE APPLICATION IS ASKING FOR SCATTER LOADING FILE
its a txt file which is on the extracted flash file folder
BROWSE it by clicking Button named Scatter Loading
click OPEN
STEP 5:
HERE IN THE DROPDOWN BOX, IT SAYS DOWNLOAD ONLY, CLICK ON IT AND SELECT FIRMWARE UPDATE ONLY.
IF YOU SELECT FORMAT + DOWNLOAD, THEN YOU WILL LOOSE IMEI NUMBER.
NOW CLICK DOWNLOAD BUTTON ( GREEN ARROWED BUTTON NAMED DOWNLOAD )
IN CASE YOU LOOSE IMEI NUMBER, THEN REFER HERE
STEP 6:
Now SWITCH OFF your PHONE and REMOVE BATTERY
STEP 7:
CONNECT your PC via USB CABLE
wait for the driver Detection.
THE FLASHING PROCESS WILL START AUTOMATICALLY you can See the progress in progress bar which is on bottom of flashing tool Application.
WHEN IT IS FINISHED DISCONNECT USB AND RESTART YOUR PHONE.
NOW YOU WILL GET LOLLIPOP UPDATE IMMEDIATELY.
NOW REFER HERE TO ROOT MARSHMALLOW
HIT THANKS IF HELPED
if link do not work here properly then just google 'canvas a1 stuck on startup' ... and follow link in associated with xda
Device is dead
My phone is neither switching on, nor charging.
I flashed the stock ROM due to some problem with the rooted device through SP Flash tools. It completed successfully, but the device is not switching on or charging.
KIndly help
Root Lenovo Tab 10 TB-X103F (Tested)
1. activate developer options on the Tablet
2. enable Bootloader-Unlock on the Tablet
3. download and install ADB und fastboot
4. latest usb driver on your PC
5. download TWRP TWRP-3.0.2_TB-X103F-beta.img
https://forum.xda-developers.com/showpost.php?p=70228684&postcount=65
6. download SuperSu zip file
Steps:
1.) boot to fastboot -> shutdown your device -> press on/off + "+" Volumekey → device restarts to fastboot mode
2.) connect to your pc via usb cable
3.) start command shell (cmd) in the fastboot instalation folder on your PC and check for the device connection with the command:
"fastboot devices"
4.) do the unlocking
"fastboot oem unlock-go"
5.) boot TWRP image file in the command line, showing the pathway to the .img file (if not in the same folder):
fastboot boot TWRP-3.0.2_TB-X103F-beta.img
6.) Put SuperSu zip file in the device memory and flash SuperSu zip with TWRP, then restart the device. Done!!!!
Stock recovery remains
RooterLeopold said:
Root Lenovo Tab 10 TB-X103F (Tested)
1. activate developer options on the Tablet
2. enable Bootloader-Unlock on the Tablet
3. download and install ADB und fastboot
4. latest usb driver on your PC
5. download TWRP TWRP-3.0.2_TB-X103F-beta.img
https://forum.xda-developers.com/showpost.php?p=70228684&postcount=65
6. download SuperSu zip file
Steps:
1.) boot to fastboot -> shutdown your device -> press on/off + "+" Volumekey → device restarts to fastboot mode
2.) connect to your pc via usb cable
3.) start command shell (cmd) in the fastboot instalation folder on your PC and check for the device connection with the command:
"fastboot devices"
4.) do the unlocking
"fastboot oem unlock-go"
5.) boot TWRP image file in the command line, showing the pathway to the file:
TWRP-3.0.2_TB-X103F-beta.img
6.) Put SuperSu zip file in the device memory and flash SuperSu zip with TWRP, then restart the device. Done!!!!
Click to expand...
Click to collapse
I have done all the steps but For some reason twrp is not installed and i still have the stock recovery. Please help
That's because the above only boots TWRP to root but does not install it. To install TWRP, when in booted with TWRP, you need to transfer the TWRP img to the tablet storage and then install it while in TWRP.
it is important to show the pathway to the file TWRP-3.0.2_TB-X103F-beta.img in the command line, like:
C:\Users\Public\Documents\My Videos\TWRP-3.0.2_TB-X103F-beta.img
Sorry for this newbie question.
Which part of the above rooting steps is rooting my tablet, what is TWRP doing and why do I need to install the SuperSU app?
During my first try I didn't boot the TWRP image rather I flashed it. But that didn't help at all.
After booting the TWRP image I was able to flash the SuperSU app.
The stock recovery is still in use.
Thanks in advance.
Read the steps carefully and follow the steps, it is a tested successfull strategy. To get deep knowlege about the background processes, please read the threads elsewhere in Web.
Yow how do you enter Fastboot on the tablet and i haved tied avery button on the tablet and i dont see the fastboot option
Entering Fastboot on Lenovo TB-X103F tablet
ShottaDopey said:
Yow how do you enter Fastboot on the tablet and i haved tied avery button on the tablet and i dont see the fastboot option
Click to expand...
Click to collapse
Hi everyone. I just want to clarify something about this procedure There's a lot of people being confused on how to get into FASTBOOT on some things, and that's stopping them getting anywhere from the beginning.
The Lenovo TB-X103F tablet doesn't have a way of booting directly into FASTBOOT. Turning the tablet On while holding either volume key and the On button doesn't do it directly. . . . . Firstly, there's 3 buttons on the tablet, I call them VOL- VOL+ PWR (again, that's just to clarify things 100%)
here's what must be done (well it's this way on the 3 I have on my desk, so I assume all TB-X103F tablets are the same) . . . . .
1) Turn the tablet off completely.
2) Press & hold the VOL+ button (the middle of the 3 buttons).
3) Press & hold the PWR button, release the PWR button as soon as anything appears on screen - Keep holding VOL+ button.
4) After about 8 seconds the familiar green android lay down will appear. Then, your recovery menu will appear.
5) Release the VOL+ button anytime now.
6) Press either VOL button to select BOOTLOADER on the menu (Bootloader is the same as FASTBOOT on this menu, that's where the confusion lies for many users).
7) Got Bootloader selected? now press PWR and let the tablet reboot itself.
8) it will show the LENOVO logo, and appear to be stuck - it isn't It's in Fastboot mode.
9) Plug in your USB to PC cable, and it'll install appropriate drivers on the PC (hopefully eh?).
10) Once the drivers are installed, test it by getting a Command Prompt in your ADB/FASTBOOT folder on your PC . . . .
11) type the command FASTBOOT DEVICES It should show you that your device is connected, if it shows no devices then either it didn't install the drivers, or something
else is wrong (there's about 30 things that can have gone wrong here, too many to go through in this quick guide).
12) The tablet will stay in FASTBOOT/BOOTLOADER mode until you turn it off (or the battery goes flat lol). So stay calm, there's no rush
I've mentioned about there being no rush, because if you choose ADB connecting from the recovery menu, it disconnects automatically after about 5 minutes -
This is Important to know because it can disconnect while you're pushing/pulling files from the tablet, and cause really nasty problems. Bad design eh?
But we're in Fastboot mode, so nothing to worry about like that
Deleted
Successful root
It was hard, but I had finally had done it. I had figured it out it is easier just to go to the command prompt (I ran it under admin) and "cd C:/adb" (where you installed the adb fastboot software) while having the TWRP image file being placed there. I only wished that I had done it sooner. And for those who are new to the custom recovery it can be overwealming, but with patience and going through the files in the file explorer to find your main storage would lead you to the SuperSU file and successfully root your device.
I flashed TWRP...now what? I can't find any instructions on how to reboot into TWRP. I got into some sort of Chinese menu (PWR + VOL-) but I'm pretty sure this is the device test menu.
So I did the "fastboot oem unlock-go" command and adb said ok but my tablet just went to a black screen and won't turn on now and I'm not sure why. I also heard the Windows USB disconnect sound when i did it.
Would this work with the TB-X104F running 8.1?
Since a few months my tablet is stuck with the 'password changed, wait....' message. I had hoped that I could overcome this with the steps mentioned here. But unfortunately not
I can't start it anymore, so I'm not sure if it is in developers mode or not. Also, plugging the device in my mac didn't let it download the drivers.
Too bad, because when it was working it was a great tablet, now it's just a expensive drawer filler
SynGamer said:
I flashed TWRP...now what? I can't find any instructions on how to reboot into TWRP. I got into some sort of Chinese menu (PWR + VOL-) but I'm pretty sure this is the device test menu.
Click to expand...
Click to collapse
its the vol+ not - you need to press with the power button
Steridroid said:
I have done all the steps but For some reason twrp is not installed and i still have the stock recovery. Please help
Click to expand...
Click to collapse
so what exactly do i have to type at the command prompt to run twrp?,ive put the twrp img file in the same folder as the adb stuff.
3.) start command shell (cmd) in the fastboot instalation folder on your PC and check for the device connection with the command:
"fastboot devices"
fastboot shows notting
lenovo seems to have killed these tablets from the old lady next doors experience.. no wifi, no adb, no fastboot, no qualcomm, just unknown device, which loads NOTHING, no drivers work!!!
First, thanks to @Uzephi and @41rw4lk for helping me to use/recover my phone. Please, read and do not underestimate the guides: our phone is tricky! We have two system partitions (slot a and b) to allow stock updates on-the-fly. This complicates the normal flashing process and if you do not follow the steps, you may bootloop. Use these guides at your own risk!
Reading this page is a good beginning to understanding the A/B partitioning scheme and how Motorola Z2 Force works:
1) Our phone has A/B partitioning, so flashing Magisk/XPosed is different
2) It does not support Project Treble (faster stock updates)
3) It does not a recovery partition, so flashing TWRP is different
Note also that the RSD Lite from Motorola has issues with Windows 10 and you’ll need to manual flash firmware if you bootloop (see Process E below). Other way is directly flashing from Qualcomm EDL mode (Emergency Download Mode) from which users can perform various tasks like unbricking, unlock bootloader, and installation of any custom ROMs.
Right now, this guide has 5 parts (maybe we can dual boot our phone in the future). If you just want to use a rooted stock ROM, please, search for other guides here on xda. These guides were written (and tested) using a Motorola Z2 Force XT1789-05 phone (Brazil), although most of it should work for other variants if you download and use proper firmware files for these other phones. For other models, better if you follow Uzephi’s guide.
A. Opening bootloader
B. Preparing the phone to move into custom ROMs (AOSP) + TWRP recovery
C. Flashing a custom AOSP ROM + rooting
D. Dirty flashing AOSP ROM updates
E. Recovering from bricks or returning to stock
F. Oreo ROM features comparison table
If you want to move your Motorola Z2 Force to Project Treble ROMs, please, check this guide.
Here is a list of the ROMs that are waiting for you.
A. Opening bootloader
With enough battery in your phone (80%), you can follow the Motorola official guide which steps are:
1. Backup everything you need. Your phone will be reseted including the internal sdcard.
2. Into the phone, enable the Developer Options clicking 7 times over the version (About section in the Settings). Go to Developer Options, click the OEM unlock option to enable it. Also enable USB debugging.
3. Install the Motorola drivers in your computer, but (in my personal experience) not the Android SDK suggested in the official guide. Instead, extract these adb/fastboot files in a blank folder of your computer.
3.1) Do not use other adb/fastboot binaries: I cannot guarantee they will work.
3.2) You need to use a USB 2.0 port of your computer. Some users report that USB 3.0 will also work.
4. Open a command line window in the adb/fastboot folder (step 3), reboot the phone into the bootloader (see adb command below or press power + volume down buttons). Plug the phone on computer (see 3.2 above). Test the connection and run the command to get the code for unlocking:
Code:
adb reboot bootloader
fastboot devices
fastboot oem get_unlock_data
You’ll get:
Code:
(bootloader) Unlock data:
(bootloader) <code 1>
(bootloader) <code 2>
(bootloader) <code 3>
(bootloader) <code 4>
(bootloader) <code 5>
5. You’ll need to join 5 codes and, after logging into your own Motorola account, check by clicking the button “Can my device be unlocked” (step 6) by Motorola here. Read the text: your warranty will be void if you go ahead. Consider if you have enough knowledge, time and money to deal with a troublesome (or bricked) device. Although, it’s not that easy to hard brick this phone (see process E below).
Code:
<code 1><code 2><code 3><code 4><code 5>
6. You’ll receive back an email with the code to unlock your bootloader (if it is available for your model). Then you’ll run the following command:
Code:
fastboot oem unlock <code 1><code 2><code 3><code 4><code 5>
7. You’ll receive a warning that all your data would be erased (see step 1 above) and need to re-run the same command to confirm. At this point, your bootloader should be unlocked. As an Android restriction, each time you boot the phone you’ll see a warning. Do nothing, wait for 5 seconds and the phone boots normally. Some users bother with this warning and try to get rid of it.
B. Preparing the phone to move into custom ROMs (AOSP) + TWRP recovery
Requirements: unlocked bootloader (see guide A) and no security lock: disable PIN, gestures and fingerprinting (because TWRP cannot read the locked/cryptographed data of the phone). Enough battery in your phone (80%).
If you do not prepare your phone to custom ROMs and if you do not have both bootloaders of the phone in the same Android version of the ROM you’ll flash, you’ll hard brick the phone and lose also the access to the bootloader! You’ve been warned: follow the guide!
Note: if you hard brick, I suggest you be prepared to follow the Unbrick Qualcomm mobiles with Step-by-step guide or the Unbrick All Qualcomm Snapdragon’s from Qualcomm HS-USB QDLoader 9008 guide, but I never tested them myself. You can also use Qualcomm Flash Image Loader (QFIL) tool.
1. Backup everything you need. Your phone will be reset including the internal sdcard.
2. Into the phone, enable the Developer Options clicking 7 times over the version (About section in the Settings). Go to Developer Options and enable USB debugging.
3. Install the Motorola drivers and the adb/fastboot files.
3.1) do not use other adb/fastboot binaries: we cannot guarantee they will work.
3.2) you need to use a USB 2.0 port of your computer. Some users report that USB 3.0 will also work.
4. Download the firmware of the same Android major version of the future ROM you’ll install (Oreo for Oreo ROMs, for instance). When (and if) we move to Android P, most probably we will need to follow this guide again.
- Retail (XT1789-05) (Europe/Brazil).
- Other models (branded): ATT, Sprint, T-Mobile (TMO), USC, Verizon.
- Note: NPXS26 versions stand for Nougat and OPXS27 for Oreo. You do not need Nougat versions for anything.
5. Extract the zip contents to a blank folder in your computer.
6. Download the FlashAll_XT1789-05.zip file, extract the content and move all files to the same firmware folder (step 5 above). Be sure to overwrite any file (if needed).
7. Run the Preparation.bat file there to generate the flashfile.bat file that will send the commands to the phone. Credits: the original preparation files were from RootJunky (can be downloaded here) and include more options that we do not need for our purpose here. Also, it includes adb/fastboot binaries that could not work with our phone.
8. Reboot the phone into the bootloader (see adb command below or power + volume down buttons). Open a command line window in the firmware folder (step 5 above), test the connection and execute the flashfile.bat file generated on step 7.
Code:
adb devices
adb reboot bootloader
fastboot devices
flashfile.bat
Never ever unplug the device from the USB 2.0 port while flashing the firmware. This could cause a hard brick and your device will be dead.
9. There is a pause at the end. You should review if everything went fine (or even click on the menu of the command line window, select all and copy&paste the contents in a .txt file for further help/revision).
10. Reboot your phone into the system (ROM) and do a quick configuration (remember that everything will be deleted when you install TWRP further…).
11. Into the phone, enable the Developer Options clicking 7 times over the version (About section in the settings). Go to Developer Options and enable USB debugging.
12. Download both the .img and .zip file of the TWRP recovery from the official site. It's the same file for all models/variants of Z2 Force phone. Put the files into our firmware folder (step 5 above). Copy the .zip file to the phone internal card. Note: versions older than 3.2.2-2 does not support PIN/Password/Fingerprint, so disable them before proceed. Most probably, ROMs before July 20th, 2018 cannot be flashed in older TWRP.
13. Now boot (not flash) the TWRP .img file using a command line window in the same firmware folder (step 5 above):
Code:
adb devices
adb reboot bootloader
fastboot devices
fastboot boot <TWRP file name>.img
14. Only now that you’re inside TWRP temporarily flash the TWRP .zip file you’ve saved into the phone (step 12 above).
15. Reboot into TWRP (use the main reboot menu in TWRP).
16. Now, you should reboot again into bootloader: inside TWRP, go to Reboot menu and choose Bootloader.
17. Now you will wipe all user data via bootloader. This is necessary to use an AOSP ROM when you come from stock. Using a command line window in the same firmware folder of your computer (step 5 above), run the following commands:
Code:
fastboot devices
fastboot -w
18. Now you can reboot the phone into System using the buttons volume up/down to navigate and confirming with the Power button. You’ll be with stock ROM and TWRP. If you want to move to a custom AOSP ROM, do a quick configuration: into the phone, enable the Developer Options clicking 7 times over the version (About section in the settings). Go to Developer Options and enable USB debugging and go to the proper guide (Process C).
C. Flashing a custom AOSP ROM + rooting
1. Requirements:
1.1 Motorola drivers.
1.2 Our custom adb/fastboot files (others may not work!).
1.3 USB debugging enabled into the Developer Options.
1.4 If you're using TWRP older than 3.2.2-2, disable disable PIN/gestures/fingerprinting. Also, most probably, ROMs after July 20th, 2018 cannot be flashed in older TWRP.
1.5 An USB 2.0 port of your computer (some users report that USB 3.0 will also work).
1.6 Two Oreo bootloaders (process B above).
1.7 Permanent TWRP
1.8 Enough battery in your phone (80%).
2. Download the AOSP ROM you want and move the .zip files to the phone. Right now, we have:
2.1 Dirty Unicorns: no need for Gapps. Official and Weeklies can be dirty flashed interchangeably. RC has a different signature. Support on Google+ page. More about DU kernel.
2.2 Lineage OS 15.1. MindTheGapps needed. OpenGapps not compatible yet. XDA thread.
2.3 Mokee: Gapps needed. Take care: online guides assume that you already have an AOSP ROM, TWRP and rooted device.
Deprecated (?)
2.4 AOSiP: no need for Gapps. XDA thread.
2.5 Invictrix. Gapps are built in. XDA thread
3. Choose the root method and download the .zip files: Magisk (suggested) or LineageOS SU Addon. Move the .zip files to phone. Note: if you bootloop on Magisk, most probably you’re flashing a wrong/different version of Magisk or you did not reboot between flashing ROM/Gapps and Magisk. Note: SuperSu is deprecated.
4. Reboot into TWRP:
Code:
adb reboot recovery
Then flash the ROM. It will be flashed in two steps only in the “other” slot. We have two slots, A and B. Our phone can be upgraded on-the-fly because the update is always applied to the slot not booted, the “other” slot. Then, immediately, flash the .zip TWRP or you will lose it.
5. Go to Reboot menu of TWRP and reboot into bootloader. Then, in the folder with adb/fastboot binaries (see 1.2 above), you need to wipe data (including sdcard) with the following commands:
Code:
fastboot devices
fastboot -w
6. Now you need to reboot the phone into System using the buttons volume up/down and confirming with the Power button (or typing fastboot reboot into the command line windows). You’ll be with an AOSP ROM and TWRP.
7. Once into the phone, enable the Developer Options clicking 7 times over the version (About section in the settings). Go to Developer Options and enable USB debugging if you intend to dirty flash ROM updates.
8. Reboot into TWRP again, flash Magisk (your settings and modules will be preserved). Note: if you bootloop on Magisk, remember it is mandatory to reboot between ROM flash (step 4 above) and GApps/Addon flash due to verity/slot-swap logic.
9. A good place to read what is not working is in the section known problems of LineageOS.
D. Dirty flashing AOSP ROM updates
1. If you follow all the processes above, you can dirty flash updates because you have:
1.1 Motorola drivers installed.
1.2 Specific adb/fastboot files for our phone and an USB 2.0 port in a Windows computer (some users report that USB 3.0 will also work).
1.3 Unlocked bootloaders (Process A above).
1.4 Permanent TWRP running and TWRP .zip file placed inside your phone and ready to be flashed again.
1.5 An AOSP ROM already running.
1.6 Developer Options and USB debugging enabled.
1.7 If you're using TWRP older than 3.2.2-2, disable disable PIN/gestures/fingerprinting. Also, most probably, ROMs after July 20th, 2018 cannot be flashed in older TWRP.
1.8 Enough battery in your phone (80%)
2. Download your ROM .zip update, copy it into the phone sdcard and reboot your phone into TWRP. See download links here.
3. Within TWRP you should flash (install) things in the following order:
3.1 ROM update .zip file. Remember that, at this time, the update will be flashed int the other slot and inside phone you’ll have both the system before update (in the booted slot) and updated ROM in the other slot.
3.2 TWRP .zip file (step 1.4 above) once again (do not skip this step or you’ll bootloop!).
4. Reboot to System: if you skip this step, you’ll bootloop.
5. Reboot into TWRP again, flash Magisk (your settings and modules will be preserved) or LineageOS SU Addon .zip file. Note: if you bootloop on Magisk, most probably you’re flashing a wrong/different version of Magisk. I suggest v16.0 and, after you got rooted with 16.0, you can update. It is mandatory to reboot between ROM flash (step 4 above) and GApps/Addon flash due to verity/slot-swap logic.
Note: SuperSu is deprecated.
6. Wipe Dalvik/ART cache: go to Wipe menu of TWRP > Advanced Wipe > Dalvik/ART Cache only.
7. Reboot your phone into System (ROM) will use the “other” slot, the one with the updated ROM.
8. You can use XPosed installer app (and reboot).
9. Now you can add your PIN, fingerprint, gestures back until next flashing.
E. Recovering from soft bricks or returning to Stock
If you’re reading this is because you already unlock your bootloader (see guide A) and anything went wrong, but you still can boot your phone into bootloader. Plug your phone and get enough battery (even if you do not see any charging signal).
1. Install the Motorola drivers and the specific adb/fastboot files for our phone. Remember, follow the rules because our device is tricky!
1.1) Do not use other adb/fastboot binaries: we cannot guarantee they will work.
1.2) You need to use a USB 2.0 port of your computer (some users report that USB 3.0 will also work).
2. Download the latest firmware for your model:
- Retail (XT1789-05) (Europe/Brazil).
- Other models (branded): ATT, Sprint, T-Mobile (TMO), USC, Verizon.
- Note: NPXS26 versions stand for Nougat and OPXS27 for Oreo. You do not need Nougat versions for anything.
3. Extract the zip contents to a blank folder in your computer.
4. Download the FlashAll_XT1789-05.zip file (it should work for other Motorola Z2 Force models as well), extract the content and move all files to the same firmware folder (step 2 above). Be sure to overwrite any file (if needed).
5. Run the Preparation.bat file there to generate the flashfile.bat file that will send the commands to the phone. Credits: the original preparation files were from RootJunky (can be downloaded here) and include more options that we do not need for our purpose here. Also, it includes adb/fastboot binaries that could not work with our phone.
6. Reboot the phone into the bootloader (see adb command below or power + volume down). Open a command line window in the firmware folder (step 5 above), test the connection and execute the flashfile.bat file generated on step 5.
Code:
adb reboot bootloader
fastboot devices
flashfile.bat
Never ever unplug the device from the USB 2.0 port while flashing the firmware. This could cause a hard brick and your device will be dead.
7. There is a pause at the end. You should review if everything went fine (or even click on the menu of the command line window, select all and copy&paste the contents in a .txt file for further help/revision).
8. Reboot your phone into system (ROM) and do not forget, later, to enable the Developer Options and USB debugging again.
Note: if you hard brick, I suggest you be prepared to follow the Unbrick Qualcomm mobiles with Step-by-step guide or the Unbrick All Qualcomm Snapdragon’s from Qualcomm HS-USB QDLoader 9008 guide, but I never tested them myself. You can also use Qualcomm Flash Image Loader (QFIL) tool. Maybe these Latest 2017 Qualcomm Diag QD-Loader Windows 10 Drivers signed will help you.
F. Oreo ROM features comparison
This is a table for Oreo ROM features comparison for Motorola Z2 Force - nash.
I would like to receive feedback and updates from the users, as I can't keep changing from one ROM to another and they get new features, updates, improvements, etc.
I consider Lineage OS 15.1 our stock ROM regarding to customization. So, it's not listed there.
Legend:
Code:
X = Feature present
XX = ROM excels in this particular feature (in my opinion).
If you want to move your Motorola Z2 Force to Project Treble ROMs, please, check this guide.
Here is a list of the ROMs that are waiting for you.
I came back to stock ROM. the problem is that it gets stuck in the initial configurations of the android trying to find a wifi network, to continue the configuration, without success, because I see in fastboot that the baseband is unknown, and I also can not install any rom, or recovery image because I have the following message in fastboot: FLASHING_LOCKED. and since I can not get past the initial android settings, I also can not unlock the developer options to enable OEM unlocking. now I'm standing in a rom that does not leave the initial configuration, it does not connect to any network and a fastboot that does not let me install anything. and I also tried the recovery mode and even tried to install an update via sideload, without success. I do not know what else to do if you can give me a light.
renanjones said:
I came back to stock ROM. the problem is that it gets stuck in the initial configurations of the android trying to find a wifi network, to continue the configuration, without success, because I see in fastboot that the baseband is unknown, and I also can not install any rom, or recovery image because I have the following message in fastboot: FLASHING_LOCKED. and since I can not get past the initial android settings, I also can not unlock the developer options to enable OEM unlocking. now I'm standing in a rom that does not leave the initial configuration, it does not connect to any network and a fastboot that does not let me install anything. and I also tried the recovery mode and even tried to install an update via sideload, without success. I do not know what else to do if you can give me a light.
Click to expand...
Click to collapse
I see two possible scenarios:
1. Your bootloader is locked (yet) (see guide A).
2. Your in a "false locked" situation that, maybe, could be solved by resetting data via recovery or in bootloader (with the command: fastboot -w).
Great tutorial, but I did not get 4g in any of the roms, only 3g
Gutto said:
Great tutorial, but I did not get 4g in any of the roms, only 3g
Click to expand...
Click to collapse
I got 4G in any ROM... AOSIP, DU or Invictrix...
Are you using a branded (carrier) phone? If not, maybe you should return to stock (to recover any changes on partitions).
Technical said:
I got 4G in any ROM... AOSIP, DU or Invictrix...
Are you using a branded (carrier) phone? If not, maybe you should return to stock (to recover any changes on partitions).
Click to expand...
Click to collapse
My cell phone and Sprint, I did every process that you indicated, but not 4G
So I followed the instructions as noted, as soon as I got to the root installation part, it started throwing a "cannot mount /system" error. I thought a reboot would solve the issue, but now I think I'm bricked. Can't boot into anything, all I can do is plug my phone in and listen to it keep disconnecting every 10 seconds or so. The phone had booted up fine prior to starting the installation process, and I don't see how just a bad ROM install is preventing me from getting into either bootloader or recovery. Any advice?
For clarity, i'm unable to use QBOOT to do anything since after it hits the "powered on" state I'm assuming it's in, it just resets and does the same thing over and over again
shalpp said:
So I followed the instructions as noted, as soon as I got to the root installation part, it started throwing a "cannot mount /system" error. I thought a reboot would solve the issue, but now I think I'm bricked. Can't boot into anything, all I can do is plug my phone in and listen to it keep disconnecting every 10 seconds or so. The phone had booted up fine prior to starting the installation process, and I don't see how just a bad ROM install is preventing me from getting into either bootloader or recovery. Any advice?
For clarity, i'm unable to use QBOOT to do anything since after it hits the "powered on" state I'm assuming it's in, it just resets and does the same thing over and over again
Click to expand...
Click to collapse
Have you tried holding vol dwn + pwr btn to force it into bootloader mode? If you can get there, then you can use the keys to get to recovery and try a factory reset. If that don't work, go back to bootloader mode and try flashing back to stock. Might double check that the battery has plenty of charge.
41rw4lk said:
Have you tried holding vol dwn + pwr btn to force it into bootloader mode? If you can get there, then you can use the keys to get to recovery and try a factory reset. If that don't work, go back to bootloader mode and try flashing back to stock. Might double check that the battery has plenty of charge.
Click to expand...
Click to collapse
I'm unable to get the phone out of qboot (or whatever it's called). I've tried using a blank-flash but all that happens is device restarts as made evident by the "device disconnect" sound playing every few seconds. The phone had around 80% when I started the process. Should I just let it die and try loading into BL after a few hours of this thing power cycling itself?
shalpp said:
I'm unable to get the phone out of qboot (or whatever it's called). I've tried using a blank-flash but all that happens is device restarts as made evident by the "device disconnect" sound playing every few seconds. The phone had around 80% when I started the process. Should I just let it die and try loading into BL after a few hours of this thing power cycling itself?
Click to expand...
Click to collapse
It's weird that it is power cycling like that. Have you tired unplugging the phone and booting? Whether it's recovery, bootloader, qboot; you need to get to one place or the other if possible because power cycling won't allow you to do anything. If you can get a stable boot in any mode I would suggest moving your cable to another port so any corruptions aren't a factor anymore. I don't think a drain will resolve anything, but I've never heard anyone mention power cycling like that.
41rw4lk said:
It's weird that it is power cycling like that. Have you tired unplugging the phone and booting? Whether it's recovery, bootloader, qboot; you need to get to one place or the other if possible because power cycling won't allow you to do anything. If you can get a stable boot in any mode I would suggest moving your cable to another port so any corruptions aren't a factor anymore. I don't think a drain will resolve anything, but I've never heard anyone mention power cycling like that.
Click to expand...
Click to collapse
Power cycling is just an assumption since regardless of whatever port its in it keeps an endless loop of connect, disconnect". Basically after rebooting the device after attempting to install the ROM is when it went black and started not doing anything other than connect, disconnect
shalpp said:
Power cycling is just an assumption since regardless of whatever port its in it keeps an endless loop of connect, disconnect". Basically after rebooting the device after attempting to install the ROM is when it went black and started not doing anything other than connect, disconnect
Click to expand...
Click to collapse
When it's trying to connect do you have a pop up on your pc showing what it sees the phone as? Does it say nash fastboot, or 9008, Z2? That might give some idea of where it's failing.
41rw4lk said:
When it's trying to connect do you have a pop up on your pc showing what it sees the phone as? Does it say nash fastboot, or 9008, Z2? That might give some idea of where it's failing.
Click to expand...
Click to collapse
It appears as Qualcomm 9008
It only starts the loop after starting a blankflash. That's about the only response I get out of the device, otherwise it does absolutely nothing, no combination of buttons do anything
Edit: Confirmed connect/disconnect on another machine with the same driver configuration
1/ WARNING: Unlocking the Bootloader WILL PERFORM A FACTORY RESET on your phone. Please backup your data BEFORE PROCEED.
2/ Should you run into any issues, please post here
Here is the good stuff. The rooting process is divided into 2 parts: Bootloader unlock and Rooting itself.
Before you begin, please download the Following
1) Download platform-tools on your computer here 11
2) Optional for Windows PC: MTK VCOM USB drivers here 5 (the default Windows driver works sometimes but not always. If the default driver doesn’t work for you, install this one)
3) Download factory-prepared patched stock BOOT.IMG here (this is patched to Magisk 20.4)
Bootloader Unlock
- Goto Teracube's Developer Options (via Settings/System/About and tap Build number several times to unlock Developer Options if this is not already available)
- Goto Settings > System > Developer settings
- Turn on OEM unlocking
- Shutdown the phone
- Press Vol+ and Power buttons simultaneously for 5/6 seconds
- You’ll see 3 options in tiny fonts. Use Vol+ to toggle option
- Select Fastboot and press Vol- to select it
- Connect Teracube to your PC/computer using the USB-C cable came with the package.
- Using platform-tools on your computer run the command
fastboot flashing unlock
Click to expand...
Click to collapse
- A confirmation message will be displayed on the screen, press Vol+ to say accept
- Bootloader is now unlocked. You will see some messages during the boot sequence each time you boot/reboot your phone. This is an expected behavior.
- Do not reboot or shutdown phone yet if you plan to continue with the root process (see below)
Root
- Perform Bootloader unlock steps (as above). Otherwise, the phone will complain of verification and will not allow you to proceed
- Connect Teracube to your PC/computer using the USB-C cable came with the package.
- Use platform-tools on your computer and run the command to flash the patched bootloader to your phone (your BOOT.IMG filename may vary)
fastboot flash boot teracube_patched_boot_sw1_magisk_20.4.img
Click to expand...
Click to collapse
- Run the following command to complete reboot your phone and complete the process
fastboot reboot
Click to expand...
Click to collapse
That’s it. Your Teracube should be rooted.
Install Magisk manager from github to check and use root.
Thank! Very useful post!
Hi, where can i find platform-tools for Ubuntu 18.04 ?
Thanks