I was using the pitaka for my note 10+ didn't looked back since then.
Light, strong, nice, wireless charging and NFC works well with the aramid fibre. I have other carbon fibre casing which causes the NFC not to work.
Anyway best part is that the case is so thin and it's compatible with any magnetic mount! This means you do not need to have a separate metal plate on your phone or case, this casing have it embedded inside the case.
You can go to the link before to get your 10% off.
https://share.ipitaka.com/x/KhB8VU
Hi!
Does the Pitaka MagEZ car mount (non wireless charging) work with that case?
They say on their web page that it doesn't, but I would think that it does....
And how did you get yours already?? they have stated that shipping will start only on 7.9.2020
BWA80 said:
Hi!
Does the Pitaka MagEZ car mount (non wireless charging) work with that case?
They say on their web page that it doesn't, but I would think that it does....
Click to expand...
Click to collapse
If you look at one of the pics I posted, it does state that it works with the car mount.
I do not have any pitaka car mount, but I uses this one other magnetic car mount and it works fine, with wireless charging too.
I placed order for my case very early. Perhaps thats why I got it early I guess.
Sent from my SM-N986B using Tapatalk
knight900 said:
I was using the pitaka for my note 10+ didn't looked back since then.
Light, strong, nice, wireless charging and NFC works well with the aramid fibre. I have other carbon fibre casing which causes the NFC not to work.
Anyway best part is that the case is so thin and it's compatible with any magnetic mount! This means you do not need to have a separate metal plate on your phone or case, this casing have it embedded inside the case.
You can go to the link before to get your 10% off.
https://share.ipitaka.com/x/KhB8VU
Click to expand...
Click to collapse
Looks like bottom camera bump isn't protected only the top... Is the correct?
ram4ufriends said:
Looks like bottom camera bump isn't protected only the top... Is the correct?
Click to expand...
Click to collapse
It actually is. Just a small bump, the reason you see it not is because I applied a camera glass protector that why it isn't
Sent from my SM-N986B using Tapatalk
knight900 said:
It actually is. Just a small bump, the reason you see it not is because I applied a camera glass protector that why it isn't
Click to expand...
Click to collapse
What camera protector are you using?
ram4ufriends said:
What camera protector are you using?
Click to expand...
Click to collapse
Just bought it online in my local country. Nothing special. Cheap stuffs.
Sent from my SM-N986B using Tapatalk
How is the cut along the side of the phone? I have had multiple cases from Pitaka but the on on my Note 10 Plus I couldn't stand and returned . They made the sides a little to short in my opinion and it was difficult to pickup because the edge. Tried the LaterCase and the sides cam up just enough to be comfortable. I want another Pitaka because the magnet and Samsung pay still working with it.
dainteg said:
How is the cut along the side of the phone? I have had multiple cases from Pitaka but the on on my Note 10 Plus I couldn't stand and returned . They made the sides a little to short in my opinion and it was difficult to pickup because the edge. Tried the LaterCase and the sides cam up just enough to be comfortable. I want another Pitaka because the magnet and Samsung pay still working with it.
Click to expand...
Click to collapse
Not too sure about what you meant, but I felt the sides are ok.
Sent from my SM-N986B using Tapatalk
BWA80 said:
Hi!
Does the Pitaka MagEZ car mount (non wireless charging) work with that case?
They say on their web page that it doesn't, but I would think that it does....
And how did you get yours already?? they have stated that shipping will start only on 7.9.2020
Click to expand...
Click to collapse
Other MagEZ cases work with the MagEZ car mount, but not the MagEZ case for Note 20 plus. However, their wireless charging car mount does work with MagEZ case for Note 20 Ultra.
Why not get the charging one? It's good to have a little charge while driving.
https://www.ipitaka.com/products/magez-mount-qi-for-s20-ultra-p40-pro
Is the air worth $10 more than the MagEz?
I have the MagEz on my S20 Ultra and rarely use the magnetic feature.
Plus, I think the finer pattern looks better even though the phone is huge.
I've been using the MagEZ case since the Note 8, and have the older Qi charging mount for my car (Not quick charge), and haven't looked back one bit. I'm trying to decide if I want to pick up the MagEZ Mount Qi Desktop, or the MagEZ Juice(Has a detachable Qi charging pack). Now that I look at their site, I might need to upgrade to the mount for the N20U......
They have some great products and even though the case doesn't offer much in the way of serious fall protection, it's very thin and has a great texture to it.
cpufrost said:
Is the air worth $10 more than the MagEz?
I have the MagEz on my S20 Ultra and rarely use the magnetic feature.
Plus, I think the finer pattern looks better even though the phone is huge.
Click to expand...
Click to collapse
If you don't use the magnetic feature, you may consider the air case. Air case is more expensive because the aramid fiber used to make the case is rarer. By the look, you can see the pattern difference, and the touch is greater. And of course, lighter and thiner, without the magnetic feature.
i would like to see them make it in different colors like they do for the iphones. Also would like to see the heavy duty case they also make for iphones
Just got the Pitaka MagEZ case and it's nice but still wish the sides came up more. Here is it compared to the Spigen slim fit. You can see when you hold the phone with the Pitaka you are holding right on the cases edge. It's super slim so not to big a deal I just feel like it's less surface area and feels like it's going to slip sometimes. I have the Latercase coming soon and will see how that one is.
For me the Pitaka Mag case looks perfect. Mine should be here any day.
Sent from my SM-N986U1 using Tapatalk
I went for the pitaka Air case. Takes noting away from the feel of the phone while adding some much needed grip
I got the ultra 10 air case and it does NOT work with the new charging mount keep sfalling off. did I order the wrong case?
pospower said:
I got the ultra 10 air case and it does NOT work with the new charging mount keep sfalling off. did I order the wrong case?
Click to expand...
Click to collapse
You did get the wrong case... air case has no metal plates, no magnetic feature. Sure thing it will fall off from the charging mount. You would need a Mag case, or get some metal strips for the air case.
Received my MagEZ case & car mount. Case is good, very light and slim, might not be super helpful for drops, but for surface level protection it should be good. There is a small amount of lift for setting the phone face down and around the camera. There appears to be a removable insert around the camera hold for the maybe 1 mm lip, but I'm not planning on taking that out, that doesn't appear to be an "intended" feature.
The car mount is good too, it holds on to the phone well
enough, but it has to rest on the camera module to get a snug grip and to charge the phone. The contact point that touches the camera is soft rubbery, so I don't think it'll scratch it, but if some dirt or something gets on there it may? Not sure
Related
Hi.
Does anyone know of a book style flip case which uses something other than a magnet to hold the lid closed?
Seems the magnets interfere with the s-pen.
Sent from the mighty Note II
Check my case here, it also has 2 slots card holder: http://forum.xda-developers.com/showthread.php?p=36168373#post36168373
VDK said:
Check my case here, it also has 2 slots card holder: http://forum.xda-developers.com/showthread.php?p=36168373#post36168373
Click to expand...
Click to collapse
That looks like exactly what I'm looking for. Could you please tell me what is called or where to order it from?
Sent from the mighty Note II
http://www.vivamadridstore.com/main/mulcaso-poni-collection-samsung-galaxy-note-p-762.html
Please note that you have to bend out the edge hook of the open flip cover a bit since it is to tight. Otherwise it woud damage your note if you open and close the flip many times
On the pricier side but the Spigen Snap is a really good case. Detachable shell from the wallet which is useful.
http://www.spigen.com/galaxy-note-2-case-snap.html
hwnstyle21 said:
On the pricier side but the Spigen Snap is a really good case. Detachable shell from the wallet which is useful.
http://www.spigen.com/galaxy-note-2-case-snap.html
Click to expand...
Click to collapse
Thanks for the suggestion. This did look like a nice case, while searching for more info on it I stumbled upon the Spigen Illuzion case which is a bit more affordable while still fulfilling all my requirements. I've just ordered one and look forward to receiving it soon.
Sent from the mighty Note II
flip cases with a magnet on the side or in the flap shouldn't be a problem.
the only real issue is with cases that use a strong magnet behind the screen.
They are a little pricey but the offer great protection.
http://izenus.com/smart-phones/galaxy-note-2.html
Sent from my SAMSUNG-SGH-I317 using Tapatalk 2
I don't know if this counts as "book style" but I've been considering getting this one recently: http://www.amazon.co.uk/o/ASIN/B00ATUYE9O?tag=adapas-21
thedicemaster said:
flip cases with a magnet on the side or in the flap shouldn't be a problem.
the only real issue is with cases that use a strong magnet behind the screen.
Click to expand...
Click to collapse
I had a flip case with magnet in the side. Found that the Pen wouldnt work on that side - Not by much - maybe 1 CM semi circle from the center of the Magnet around the screen.
So I removed it with a scalpel, took a little while since it was glued in but once removed all worked well expect that the case wouldnt hold shut which honestly was no big issue.
Does anyone know of a reasonably solid in-car holder that will grip the Note 2 while it has the official Samsung flip case on? I assume there isn't going to be one built for purpose so just need a reasonably strong universal one, presumably windscreen mount.
Anyone got a decent one they use that can hold the weight and size?
3Shirts said:
Does anyone know of a reasonably solid in-car holder that will grip the Note 2 while it has the official Samsung flip case on? I assume there isn't going to be one built for purpose so just need a reasonably strong universal one, presumably windscreen mount.
Anyone got a decent one they use that can hold the weight and size?
Click to expand...
Click to collapse
Just picked up the iOttie XL for my new-to-me Note 2, works great. Best quality car dock I've had yet. Fits the Note 2 with a Case Mate Tough Case just barely! I understand the Note 2 with an Otterbox Defender is too big for it, but it should be fine for your application.
Looks good, thanks, I'll give it a try
3Shirts said:
Looks good, thanks, I'll give it a try
Click to expand...
Click to collapse
iOttie should work well, check out my review links in the signature. But keep in mind that if you planning to go later with Zerolemon battery or thicker case like Defender, iOttie side grips won't cut it.
Ram mount x grip will work.
http://www.rammount.com/CatalogResu...45072079076045085078049048066085/Default.aspx
self mod
I don't know if this is what you are looking for but I mod this myself. I use two 1 inch rubberband and a rubber case where i cut along the side, top, and bottom.
I don't know why the picture is upside down when I uploaded
Rocketfish makes a decent mount that will fit a Note II with an Otterbox Defender. The contact points are flexible rubber, and seem like they'd securely grip any case. It comes with both suction and vent clip mounts, I've been very happy with it.
http://www.bestbuy.com/site/Rocketf...lack/9953877.p?id=1218200308619&skuId=9953877
I have found a few on eBay from china for the S8 and i see that SCF has a Note 8 one listed but only one view and it appears to be CF and aTPU. I would liek to have something that is only CF.
Anybody seen any?
Check out Pitaka carbon fiber case for Note 8. They just launched it yesterday. Amazing company and products.
bigmann77 said:
Check out Pitaka carbon fiber case for Note 8. They just launched it yesterday. Amazing company and products.
Click to expand...
Click to collapse
Thanks, just ordered.
If you're feeling up to it I'd like to hear your thoughts on the case. It's a sexy beast for sure although the protection is almost non-existent.
will check pitaka too
I am using a Spigen Neo Hybrid so I am expecting the same/similar protection from this case. I will be more than happy to do a review once it arrives. I am a car guy so this case was right up my alley, I also liked the addition of the metal plates for magnet mounting that don't interfere with normal activity.
Would the embedded metal plate block wireless charging/tap&pay?
It looks like the Pitaka carbon fiber case for Note 8 has the plate embedded and probably would restrict the functionality of the device.
If you read through the site the metal is implemented in such a way that it does not interfere with wireless charging or NFC. I don't know if that means it is woven in somehow or offset to where the charging coil is, nor do I have one to try myself - Just regurgitating what I read.
There are two magnets with a gap between that locate the phone so that the gap is centered over the coil to allow for charging, they've got a blow out of it on their site. I'm thinking it would work on most wireless charging pads so long as the phone was placed correctly. oarenj should set us straight soon.
Got it and put up a full review here https://forum.xda-developers.com/ga...view-pitaka-aramid-fiber-case-note-8-t3702737
Are there any cases besides the sold out Pitaka one that support both features?
XVIDA StickyPad compatible with most cases
skinote said:
Are there any cases besides the sold out Pitaka one that support both features?
Click to expand...
Click to collapse
Apologies for the long reply...
You can check out XVIDA. I use the XVIDA Car Mount and an XVIDA StickyPad. (Note the XVIDA StickyPad works with the phone naked or with a smooth back case)
The are three variants. Suction Cup, Air Vent, and CD Slot Mount.
I also use their Desk Mount and Mountable Pad.
I am not sure if the XVIDA StickyPad is compatible with the Pitaka case. I am curious to know though. I have an X-Doria Galaxy Note 8 Case Defense Lux Carbon Fiber case, XVIDA StickyPad, Case friendly 0.33mm dot matrix tempted glass protector, and a uh ring finger thing. I like how the Pitaka case looks not sure about drop protection.
This case and screen protector combo has saved from a weird drop. Flying out of my hands screen first unto the metal protusions of a shopping cart. Broken screen protector near the Iris scanner and bottom near the default location of the back button. Screen was saved with no scratches or anything. I panicked though since this was just 3 days from my purchase.
Note:
If the Note 8 case isn't smooth you need to use stronger double sided adhesives.
raphael.atienza said:
Apologies for the long reply...
You can check out XVIDA. I use the XVIDA Car Mount and an XVIDA StickyPad. (Note the XVIDA StickyPad works with the phone naked or with a smooth back case)
The are three variants. Suction Cup, Air Vent, and CD Slot Mount.
I also use their Desk Mount and Mountable Pad.
I am not sure if the XVIDA StickyPad is compatible with the Pitaka case. I am curious to know though. I have an X-Doria Galaxy Note 8 Case Defense Lux Carbon Fiber case, XVIDA StickyPad, Case friendly 0.33mm dot matrix tempted glass protector, and a uh ring finger thing. I like how the Pitaka case looks not sure about drop protection.
This case and screen protector combo has saved from a weird drop. Flying out of my hands screen first unto the metal protusions of a shopping cart. Broken screen protector near the Iris scanner and bottom near the default location of the back button. Screen was saved with no scratches or anything. I panicked though since this was just 3 days from my purchase.
Note:
If the Note 8 case isn't smooth you need to use stronger double sided adhesives.
Click to expand...
Click to collapse
I already have 2 scosche magnetic car mounts, so I was hoping for a solution that used those...that stickypad sounds like it might work, though, if there aren't any other options.
skinote said:
I already have 2 scosche magnetic car mounts, so I was hoping for a solution that used those...that stickypad sounds like it might work, though, if there aren't any other options.
Click to expand...
Click to collapse
Oh sadly the Scosche Magnetic Car Mounts won't work. The magnets have to be around the qi wireless charging transmitter on the mount. Magnets and metal interferes with Qi wireless charging. In fact Qi wireless charging also slightly interferes with the S-Pen when using a wireless charging powerbank. I even got a notification pop-up stating that.
Mophie also has a solution but I don't want a battery case.
raphael.atienza said:
Oh sadly the Scosche Magnetic Car Mounts won't work. The magnets have to be around the qi wireless charging transmitter on the mount. Magnets and metal interferes with Qi wireless charging. In fact Qi wireless charging also slightly interferes with the S-Pen when using a wireless charging powerbank. I even got a notification pop-up stating that.
Mophie also has a solution but I don't want a battery case.
Click to expand...
Click to collapse
Hrm, yeah the mophie also isn't water resistant. Wonder if the Pitaka really is the only solution for the time being...? Too bad so many people seem to be having customer support issues with them!
I have a Pitaka case and it is the only one that works with mag mounts and wireless charging. I think Pitaka is just overwhelmed with orders. Before I got this case I had to use a metal plate a small one and put it on the outside of my case all the way up by the camera for it to work with my wireless charger. It looks horrible but it worked. So when I heard about Pitaka I jumped on it fast. I ordered mine and the car mount and I received it in about 8 days. I would just keep checking back with them. It is well worth it.
Actually.. I did a slight modification to my spiegen, and it does both.. The only thing I did was cut one of the round magnets in half, and then, placed it in the normal indention for the magnet.. And I have used it now, for at least a good month without issue.. I also turn the phone landscape on the charging stand sometimes to watch a video while charging...
Sent from my SM-N950U using Tapatalk
MatroxD said:
Actually.. I did a slight modification to my spiegen, and it does both.. The only thing I did was cut one of the round magnets in half, and then, placed it in the normal indention for the magnet.. And I have used it now, for at least a good month without issue.. I also turn the phone landscape on the charging stand sometimes to watch a video while charging...
Sent from my SM-N950U using Tapatalk
Click to expand...
Click to collapse
Which spigen case? sounds like an easy mod
skinote said:
Which spigen case? sounds like an easy mod
Click to expand...
Click to collapse
It was very easy mod.. Took about 3 minutes to cut the magnet.. The most difficult part of course was cutting the magnet(but if you have a dremel, it's a non thought). And it is the thin fit case.. Very, very easy.... Link below to the case and the magnets:
Spigen Thin Fit Galaxy Note 8 Case with SF Coated Non Slip Matte Surface for Excellent Grip and QNMP Compatible for Galaxy Note 8 (2017) - Matte Black https://www.amazon.com/dp/B073R7DFG1/ref=cm_sw_r_cp_apa_3zFgAb7GTE32F
Spigen Kuel A210 Metal Plates for Magnetic Car Mount Phone Holder QNMP Compatible [4 Pack - 2 Round, 2 Rectangle] - Black https://www.amazon.com/dp/B01E4U4X1I/ref=cm_sw_r_cp_apa_5DFgAbYYKBABH
Sent from my SM-N950U using Tapatalk
If you are willing to pay the price. Mophie's Charge Force line has this.
about 50 for the case and another 50 for the car charger.
100 for the case for the battery case version
MatroxD said:
It was very easy mod.. Took about 3 minutes to cut the magnet.. The most difficult part of course was cutting the magnet(but if you have a dremel, it's a non thought). And it is the thin fit case.. Very, very easy.... Link below to the case and the magnets:
Spigen Thin Fit Galaxy Note 8 Case with SF Coated Non Slip Matte Surface for Excellent Grip and QNMP Compatible for Galaxy Note 8 (2017) - Matte Black https://www.amazon.com/dp/B073R7DFG1/ref=cm_sw_r_cp_apa_3zFgAb7GTE32F
Spigen Kuel A210 Metal Plates for Magnetic Car Mount Phone Holder QNMP Compatible [4 Pack - 2 Round, 2 Rectangle] - Black https://www.amazon.com/dp/B01E4U4X1I/ref=cm_sw_r_cp_apa_5DFgAbYYKBABH
Sent from my SM-N950U using Tapatalk
Click to expand...
Click to collapse
Cut the magnet, or the metal plate?
I think I'll try the same thing with this caseology one
jason504 said:
I have a Pitaka case and it is the only one that works with mag mounts and wireless charging. I think Pitaka is just overwhelmed with orders. Before I got this case I had to use a metal plate a small one and put it on the outside of my case all the way up by the camera for it to work with my wireless charger. It looks horrible but it worked. So when I heard about Pitaka I jumped on it fast. I ordered mine and the car mount and I received it in about 8 days. I would just keep checking back with them. It is well worth it.
Click to expand...
Click to collapse
Can you post a review and photos? Thank you
raphael.atienza said:
Can you post a review and photos? Thank you
Click to expand...
Click to collapse
https://forum.xda-developers.com/ga...itaka-aramid-fiber-case-note-8-t3702737/page7
skinote said:
Cut the magnet, or the metal plate?
I think I'll try the same thing with this caseology one
Click to expand...
Click to collapse
The magnet actually is the metal plate.. So it's one in the same..
Sent from my SM-N950U using Tapatalk
MatroxD,
Are you saying that you cut the round metal plate in 1/2 and only using half of the metal plate on the top part of the case cut out to provide more room for the wireless charging magnets?
Thanks
Elvis
elviso33 said:
MatroxD,
Are you saying that you cut the round metal plate in 1/2 and only using half of the metal plate on the top part of the case cut out to provide more room for the wireless charging magnets?
Thanks
Elvis
Click to expand...
Click to collapse
I think your complicating it in your head, more than it really is, in action.. Visualize what I wrote, and then, look at the two pieces that I linked to.. And it will come to you.. You honestly just cutting the magnet (plate) in half and sticking it in the case indention that is already there.. Versus using the whole thing.. It's really, truly not technical at all..
Sent from my SM-N950U using Tapatalk
---------- Post added at 02:21 PM ---------- Previous post was at 02:15 PM ----------
I figured it would be better if I just posted a picture..
Sent from my SM-N950U using Tapatalk
Ugh.. Won't let me put the picture in... Crazy Tapatalk..
Had to go web view for this.. lol
MatroxD said:
Had to go web view for this.. lol
Click to expand...
Click to collapse
Huge thanks. That's what I was thinking you meant! :good::good:
elviso33 said:
Huge thanks. That's what I was thinking you meant! :good::good:
Click to expand...
Click to collapse
No problem.. Hopefully it helped.. I just thought to myself when I got the 8 that there has to be an easier way to solve this.. I may at some point end up ordering that carbon case (honestly, it's just a sweet case), but spending 50.00 on a case, for me, I have a ton of hobbies already that suck up enough money..
Sent from my SM-N950U using Tapatalk
Am I the only one that doesn't use the metal plate the mount comes with? It just sticks to my phone without having to use a metal disc. I'm using a sosche magnetic mount, same story with my previous s7e and s8+, granted I am using one of the super thin peel case.
How good is the Pitaka Mag case, along with the magnetic wireless charger? Are they worth the price tag? I'm wondering if there are any discount codes floating around?
MagEZ Case for Samsung Galaxy S21/S21+/S21 Ultra - PITAKA
A durable and minimalist case for Galaxy S21, S21+ and S21 Ultra. Magentic compatibility with MagEZ magnetic chargers and accessories.
www.ipitaka.com
I ordered it and sent it back, because I got sweaty hands from the case and it was very fast full of fingerprints. The carbon one might be better
What's the carbon one? The Air?
None of Pitaka is carbon, they are all aramid. Both the magez and the air case are the same material. The air does not have metal plates embedded and is therefore a little thinner.
Opinion: They are brilliant.
I got this case its light and have 360 + camera protection, added a rounded metal plate on the bottom of the phone and got this very strong magnetic holder love this setup, maybe don't like that there is no raised top and bottom, only 4 corners are raised be like 1-2 mm so placing the phone on the table face down is possible but not recommended imo unless you have some protector on the screen. Also you can check Mous case and mounts they look rly nice and have epic protection but they should increase phone bulkiness a lot.
mankvl said:
I got this case its light and have 360 + camera protection, added a rounded metal plate on the bottom of the phone and got this very strong magnetic holder love this setup, maybe don't like that there is no raised top and bottom, only 4 corners are raised be like 1-2 mm so placing the phone on the table face down is possible but not recommended imo unless you have some protector on the screen. Also you can check Mous case and mounts they look rly nice and have epic protection but they should increase phone bulkiness a lot.
Click to expand...
Click to collapse
Yes, Mous case are indeed very good protection and quite good looking.
I'm waiting for their magnetic charger to come out to try it eventually.
But to come back to op question, yes I think Pitaka case looks great, but keep in mind that it is very minimal protection, if that's important to you.
By the way, anyone can think why the thinner lighter without metal version of the Pitaka case is more expensive than the magnetic one?