There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
Hi,
At first I would like to apologize for any grammar errors I'm from Holland but I'll try to do it right
I've gotten myself into a problem, I tried to update my Galaxy S which runs on Froyo and it's rooted.
It all went pretty well until I had to reboot my phone, it show the moving S sign and plays the music at start-up but wont go any further and keeps displaying a black screen and from time to time it vibrates a bit.
I don't know what I should do now and any help would be very much appreciated.
If someone needs moor information about the error or something else just say so
Greetings!
hello i had the exact same problem as you. in the end i had to reset factory setting which will delete most of the data (on mine it deleted text messages and contacts). however this was months ago and there may be a better fix now (where you get to keep the data)
but with the phone off press and hold voume up + home button + power buton together for a few seconds (untill galaxy s appears on screen) and select the data reset option (volume keys are up and down, power key is used to select the highlighted option)
if you follow my method then you MAY lose data nut you will get your phone back. however there MAY be a better way than that.
Hi,
yes I've tried that but I can't seem to acces that menu, when I press home + power button + volume up it gets me in a loop of showing Galaxy S GT-19000, and then it keep on rebooting. So or I'm doing something wrong or my phone isn't working properly.
Seems that you have a broken SBL ( secondary boot loader ) . It can be fixed but you first need to make yourself or buy a Galaxy S Jig to enter Download mode , where you can flash a rom and hopefully repair your SBL also ( with Bell i9000M rom I repaired my SBL).
Yea, if the phone isnt detected by your computer you will need to make/buy a jig. Newer galaxy s phones had the option to enter download mode and recovery disabled.
OmerX said:
Seems that you have a broken SBL ( secondary boot loader ) . It can be fixed but you first need to make yourself or buy a Galaxy S Jig to enter Download mode , where you can flash a rom and hopefully repair your SBL also ( with Bell i9000M rom I repaired my SBL).
Click to expand...
Click to collapse
ste1164 said:
Yea, if the phone isnt detected by your computer you will need to make/buy a jig. Newer galaxy s phones had the option to enter download mode and recovery disabled.
Click to expand...
Click to collapse
Well went to the store were I bought the phone, and they couldn't access the phone, he was able to get it into the download mode but he wasn't able to download any roms to it.
So he send it to Samsung because I still got my factory warranty so its up to them I gues..
Hello,
I just bought for my mother a galaxy mini. Now i root the phone with superoneclick. i downloaded rom manager and clicked on the first option flash clockwork mod, there was a popup and i clicked the first one accidentatily and after a few seconds he said he was finished.. i turned of the phone and know he deosn't do anything at all no recovery, no download mode please help me fix the phone!
----
Edit
I just discovered that when i have plugged in the phone to the computer, and i press the buttons for recovery mode then the computer recognize my phone. Can i do anything now to make my phone work again, it seems like my display doesn't turn on by a wrong rom installed
bricked. (not very sure,cwm frm rom manager is partially supported now. work in progress)
only if ur able to get into download mode u'll be able to flash a rom...
http://androidforums.com/samsung-ga...-unbrick-mini-s5570-bricked-black-screen.html
That is a nice, nasty, hard brick.
If you are getting into download mode and ODIN running on the PC recognises your phone, you are lucky - get any stock rom from samfirmware and flash it first. Use the phone for a few days more, and then, you can upgrade to new 7.1 cyanogenmod ROM.
try going into download mode by holding home and vol down the connect the usb 2 ur phone
or try holding vol up+down home and power
if it doesnt work try getting a jig from ebay
get a jig its the only way to fix it
SSC (Samsung Service Center) is the only way.
Congrats, next time read before doing anything.
Hi everyone,
today I received my s10 Exynos version 128gb 8gb.
After transferring my data and started to configure my phone.
Right after installing the gcam 3.5 of Idan for rootless phone, I tried to make a screenshot with the Bixby and power button,
and the phone turns off, when I decided to turn on boom, some upload page with a message kernel crashed, after that I held power and v+dwn and the phone booted on safe mode, and this loop of the message and the safe mode like 5 times, then in safe mode I uninstalled the gcam of idan, and apparently for now all goes fine.
i don't know what to do, I saw this was a little normal in old phones, but can't find any information about that on s10 yet.
Anyone with the same problem? What did you make for resolving that?
Sorry for the bad English.
Thanks for everyone, by now my advise is not to install the gcam 3.5 of Idan that I download on their website.
Below I will post the link that I downloaded the apk
https://f.celsoazevedo.com/file/gcamera/GCam_5.1.018.177470874.41362666_IDan_N6_3.5_fix.apk
thanks for everyone!
EDIT: i just figure it out, that the button of volume down is stucked down, so when i hit the power it just inter in safe mode, i donto know what to do but i think thats the problem
EDIT2: volume down button stucked forcing the phone to always boot at safe mode. returning this phone
I have download & installed this rom which is called BananaDroid from this thread : https://forum.xda-developers.com/t/...te-unofficial-bananadroid-06-07-2023.4593603/
it wasn't precationarily closed when I installed the rom, my phone now keeps bootloop with no access to recovery or download mode using the volume up + power button + bixby or bixby + volume up + insert power cable, same thing with volume down to enter download mode, I installed many roms over the years since 2013 but this time my phone is totally unresponsive to any solution, after draining the battery I tried to enter the Download mode or recovery (TWRP) was installed, after flushing the rom now once connected to charger or PC it turns on by itself and shows samsung S9+ and keeps bootloop without any regard to the methods to enter the DL Or recovery is my phone done or is there a way to fix it I hope I was clear aboth the problem, I was a victim to this man's malicious custom rom.
Abdullah_95 said:
I have download & installed this rom which is called BananaDroid from this thread : https://forum.xda-developers.com/t/...te-unofficial-bananadroid-06-07-2023.4593603/
it wasn't precationarily closed when I installed the rom, my phone now keeps bootloop with no access to recovery or download mode using the volume up + power button + bixby or bixby + volume up + insert power cable, same thing with volume down to enter download mode, I installed many roms over the years since 2013 but this time my phone is totally unresponsive to any solution, after draining the battery I tried to enter the Download mode or recovery (TWRP) was installed, after flushing the rom now once connected to charger or PC it turns on by itself and shows samsung S9+ and keeps bootloop without any regard to the methods to enter the DL Or recovery is my phone done or is there a way to fix it I hope I was clear aboth the problem, I was a victim to this man's malicious custom rom.
Click to expand...
Click to collapse
Find sd card, download any custom rom(noble rom or ling) copy to sd and insert in phone...flash from twrp done..later u can try to flash stock with odin
Ps sorry i not read, u cant enter in recovery
I have the same problem with my Note 9. I installed Deepfest Rom using OrangeFox Recovery and everything worked just fine for 3 Months or so. Suddenly my phone went off and started displaying the prior mentioned beviours.
Any help will be much appreciated