Hi. When I changed in settings network mode to 2G only, signal icon started to flicker. After reboot I have no signal at all (it is impossible to call, send/receive SMS, use data connection etc.). In info (*#*#4636#*#*) preferred mode is set to "WCDMA preferred" and I cannot change it - I can chose another value from list but changes are not saved.
In settings phone says that none of SIM cards are inserted - but I can now access SIM 1 settings. However, everything is blocked and beneath the network type there is a description: "Invalid Network Mode (-1). Ignore.".
It happend when I was on latest official CM 13.0 nightly but this is probably not ROM's fault. Problem didn't disappear after clean flash, after restore or even after flashing whole set of images with official MiFlash tool.
After some research I found that setting ro.telephony.default_network from 22,22 to 10,10 should work, as 10 is for "LTE/GSM auto" when 22 is incorrect value. Separated by comma for two SIM slots. Ok, so I tried to edit build.prop with some apps without luck - access denied (rooted). I tried to mount system rw from Root explorer - nothing happens, still ro. From ADB - no, "dev/block/bootdevice/by-name/system is read-only". I even tried to change SELinux to permissive but still nothing
Every idea is welcome, I just need to get my phone to work as a phone again
Hello Brothers...
I've some questions about B588 ROM, I'm currently using Sokkoban's B574 Custom ROM and it's all additional features suit my requirements but I've heard that B588 has latest security patch... Can you guys tell me what features are missing in that stock B588 ROM from the list below..??
1. Light Painting
2. Pro Camera
3. Call Recording
4. Network Speed In StatusBar
5. Additional Gestures ( like raise to hear or voice control etc )
Thanks In Advance
yes, its missing and they will be not able to add
hbilalshah said:
Hello Brothers...
I've some questions about B588 ROM, I'm currently using Sokkoban's B574 Custom ROM and it's all additional features suit my requirements but I've heard that B588 has latest security patch... Can you guys tell me what features are missing in that stock B588 ROM from the list below..??
1. Light Painting
2. Pro Camera
3. Call Recording
4. Network Speed In StatusBar
5. Additional Gestures ( like raise to hear or voice control etc )
Thanks In Advance
Click to expand...
Click to collapse
1. Missing
2. It's present
3. Missing, but shouldn't be a problem active this feature.
4. It's present
5. It's present
kilroystyx said:
1. Missing
2. It's present
3. Missing, but shouldn't be a problem active this feature.
4. It's present
5. It's present
Click to expand...
Click to collapse
Can you please tell me how to activate the third one
hbilalshah said:
Can you please tell me how to activate the third one
Click to expand...
Click to collapse
Check out this thread
https://forum.xda-developers.com/mate-7/general/emui-4-0-manual-call-recorder-mt7-emui-t3363838
kilroystyx said:
Check out this thread
https://forum.xda-developers.com/mate-7/general/emui-4-0-manual-call-recorder-mt7-emui-t3363838
Click to expand...
Click to collapse
Thank You So Much
I more thing... I am gonna write a procedure I would do to install B588 Stock, Can you please tell me if it is right or wrong or if any step is wrong in between..??
I've B574 Custom by sokkoban installed so first I would :
1 ) Downgrade to Lollipop B052
2 ) Upgrade to B170 via OTA
3 ) Upgrade to B560 via Dload
4 ) Upgrade to B564 via OTA
5 ) Upgrade to B574 via OTA
6 ) Upgrade to B580 via OTA
7 ) Upgrade to B584 via OTA
8 ) Upgrade to B588 via OTA
Is it okay..??
Just install the newest with dload
hbilalshah said:
Thank You So Much
I more thing... I am gonna write a procedure I would do to install B588 Stock, Can you please tell me if it is right or wrong or if any step is wrong in between..??
I've B574 Custom by sokkoban installed so first I would :
1 ) Downgrade to Lollipop B052
2 ) Upgrade to B170 via OTA
3 ) Upgrade to B560 via Dload
4 ) Upgrade to B564 via OTA
5 ) Upgrade to B574 via OTA
6 ) Upgrade to B580 via OTA
7 ) Upgrade to B584 via OTA
8 ) Upgrade to B588 via OTA
Is it okay..??
Click to expand...
Click to collapse
Vinnipinni said:
Just install the newest with dload
Click to expand...
Click to collapse
And if that fails, remember you can flash via fastboot commands too.. For me dload method didn't work, so I flashed 4 images: boot, recovery, cust and system, via fastboot
amageek said:
And if that fails, remember you can flash via fastboot commands too.. For me dload method didn't work, so I flashed 4 images: boot, recovery, cust and system, via fastboot
Click to expand...
Click to collapse
hmm....Thanks Bro
I'll do it with-in a day or two...
Not in my phone
kilroystyx said:
1. Missing
2. It's present
3. Missing, but shouldn't be a problem active this feature.
4. It's present
5. It's present
Click to expand...
Click to collapse
Why in my phone those features not are activated ? And how I can activate or turn on ?
It also does not allow me to change the themes
I was in ALE-L21 C432B560 and update to ALE-L21 C432588
Bacteriandroid said:
Why in my phone those features not are activated ? And how I can activate or turn on ?
It also does not allow me to change the themes
I was in ALE-L21 C432B560 and update to ALE-L21 C432588
Click to expand...
Click to collapse
1. Light Painting
=> I wish that in the B588
2. Pro Camera
=> Isn't available in yours?
=> Could you please share a printscreen like you see bellow?
3. Call Recording
=> Check this out:
https://forum.xda-developers.com/showpost.php?p=70616704&postcount=29
4. Network Speed In StatusBar
=> Settings -> Data traffic management -> Settings -> Display network speed
or
=> Settings -> Notification panel & status bar -> Display network speed
=> See pics enclosed
5. Additional Gestures ( like raise to hear or voice control etc )
=> In mine I have voice control by default
=> After you activate Gyroscope then additional features are visible for enabling:
=> Settings -> Smart assistance -> Motion control
- Pick up
- Raise to ear
- Tilt
If you dont know how to activate Gyroscope you can use mine flashble zip to install via TWRP
https://mega.nz/#!lIJhFbYZ!FKPa9IA-A_cFphePcUFtzWEjAXGDjCLBIbxJHYj_x44
=> To Change themes you have to create a Huawei ID account.
How did you enabled OTG support bro..??
kilroystyx said:
1. Light Painting
=> I wish that in the B588
2. Pro Camera
=> Isn't available in yours?
=> Could you please share a printscreen like you see bellow?
3. Call Recording
=> Check this out:
https://forum.xda-developers.com/showpost.php?p=70616704&postcount=29
4. Network Speed In StatusBar
=> Settings -> Data traffic management -> Settings -> Display network speed
or
=> Settings -> Notification panel & status bar -> Display network speed
=> See pics enclosed
5. Additional Gestures ( like raise to hear or voice control etc )
=> In mine I have voice control by default
=> After you activate Gyroscope then additional features are visible for enabling:
=> Settings -> Smart assistance -> Motion control
- Pick up
- Raise to ear
- Tilt
If you dont know how to activate Gyroscope you can use mine flashble zip to install via TWRP
https://mega.nz/#!lIJhFbYZ!FKPa9IA-A_cFphePcUFtzWEjAXGDjCLBIbxJHYj_x44
=> To Change themes you have to create a Huawei ID account.
Click to expand...
Click to collapse
How did you enabled OTG support bro..??
hbilalshah said:
How did you enabled OTG support bro..??
Click to expand...
Click to collapse
I think stick mount works. I haven't actually tried it myself but it should work. It requires ROOT access by the way.
De EmperoR said:
I think stick mount works. I haven't actually tried it myself but it should work. It requires ROOT access by the way.
Click to expand...
Click to collapse
How did you do that anyway
hbilalshah said:
How did you enabled OTG support bro..??
Click to expand...
Click to collapse
De EmperoR said:
I think stick mount works. I haven't actually tried it myself but it should work. It requires ROOT access by the way.
Click to expand...
Click to collapse
HaiderHady said:
How did you do that anyway
Click to expand...
Click to collapse
To have OTG on the settings you have to add the following line in the build.prop file:
HTML:
ro.config.hw_otgFeature=true
See all proceess described on the pics enclosed
So far I didnt do any kind of test to check if OTG it is working, and I'm not thinking to do it, because according @XePeleato this feature wont work in our devices. Why he is giving 50$ to who can activate OTG?
https://forum.xda-developers.com/showpost.php?p=70717378&postcount=231
You can also get to that OTG feature with Quick shortcut maker from GP without having root. But enabling it doesn't affect anything. Even with external source of power. That means: NO OTG FOR P8 LITE!
Hi All,
TLDR:
- LineageOS 16, Dual-SIM
- Deactivated second sim in the settings
- Updated to LOS 17.1
- SIM is still deactivated, no button to enable
- Looking for ways to remove SIM card settings
before upgrading from LineageOS 16 to 17.1, I had my second sim card disabled via the general slider (it's my business sim, and I was on vacation). This slider feature now seems to be gone in LOS 17 but the sim is still in a disabled state, meaning LOS is not even asking me for a pin on boot, instead I receive a message saying "Adroid System" / "There's an internal problem with your device. Contact your manufacturer for details". I can still see the sim in the settings (which actually freeze if I try to change carrier settings), and the sim is visible in the top bar with zero reception and the "x". I can still use the sim card in other phones, but the OP3T seems to have memorized the sim card settings somewhere, regardless of which sim slot I use. My solution would have been to delete the per-sim settings, that LOS seems to be storing somewhere, but I have no idea where they could be located.
Any pointers or other ideas would be much appreciated. Thanks!
Same issue here:
System:
- Hardware: OnePlus 3T
- Firmware: 9.0.3
- Recovery: TWRP 3.3.1-1
- Software: LineageOS April 25, 2020
Symptom:
Dual SIM issue: SIM1 (in slot1) works as expected. SIM2 (in slot2) never connects to its network. I use SIM1 mainly for calls, SIM2 mainly for data.
Tried:
- to update firmware to 9.0.6, no change
- to swap SIM1 and SIM2, SIM1 still works in slot2, SIM2 does not work even in slot1, no change
- to remove SIM1 and keep only SIM2 (slot1 or slot2), no change.
- to use different bands GSM/WCDMA only for SIM1 (was GSM/WCDMA/LTE) and LTE only for SIM2 (was GSM/WCDMA/LTE), no change
Hints:
- when I installed LOS17.1, SIM2 was probably locked (I only unlock it when I used mobile data)
- at boot, only PIN1 is asked, not PIN2
- in SIM2's menu, choosing "Advanced > Access point names" crashes `Settings`.
- when SIM1 is not inserted, only SIM2, the `Mobile data` icon in `Quick tiles` does nothing
I looked in this XDA thread dedicated to LineageOS 17.0/17.1 on OnePlus 3/3T, and found several messages complaining about SIM cards not being detected. The problem seems different and the solution suggested is outdated, since the line is now already in `init.qcom.rc`.
The most similar issue is this thread, I cross posted in reddit. I searched gerrit for `dual sim` in the lineage-17.0 and lineage-17.1 branches as well `sim` in the oneplus_oneplus3 tag, without success.
Any idea?
Summary: `/data/system/radio` seems to be broken. Should be replaced with the same directory from a clean install. This breaks PIN auth, which means that
`/data/system/locksettings.db` has to be removed as well, and the PIN reconfigured.
Steps:
0. reboot in TWRP
1. backup broken `data` partition
2. wipe data partition
3. adb sideload `lineage-17.1-20200423-nightly-oneplus3-signed.zip` and `open_gapps-arm64-10.0-nano-20200516.zip`
4. reboot in system
5. make sure that both SIM cards are unlocked and working
6. reboot in TWRP
7. backup working `data` partition (or copy `/data/system/radio` somewhere)
8. restore broken `data` partition
9. move `/data/system/radio` to `/data/system/radio_broken`
10. put instead `/data/system/radio` extracted at step 7, either by gunzip/untar backup, or from the "somewhere" you selected
11. delete `/data/system/locksettings.db`
12. reboot into system
13. unlock both SIM cards
14. set a PIN
Done
why are the devs unable to solve that with an update or flashable zip?
Notor1ouS- said:
why are the devs unable to solve that with an update or flashable zip?
Click to expand...
Click to collapse
Clean flashing on major version bumps will always avoid this issue in the very first place. In my opinion there are much more important topics for a dev to focus on then getting dirty upgrading major versions fool-proof as long as clean flashing works flawlessly and fool-proof.
i disagree on that. a competent dev should be able to do that.
but that's going nowhere anyway, so I'm out.
Notor1ouS- said:
i disagree on that. a competent dev should be able to do that.
but that's going nowhere anyway, so I'm out.
Click to expand...
Click to collapse
If you have the competences and the knowledge to fix issues from dirty upgrading, go ahead, dirty upgrade and fix the issues.
If you don't have the competences and the knowledge to fix issues from dirty upgrading, go ahead and clean flash as recommended on major version bumbs.
If you don't have the competences and the knowledge to fix issues from dirty upgrading and you are resistent to recommendations, blaming the devs as incompetent will polish your ego but don't fix the issue.
For a community driven open source project, you can easily push a fix instead of blaming the devs as incompetent!
Be a user - not a customer.
Activate VoLTE & VoWIFI on custom/stock ROMs with any Carrier
Yes, yes, I know that this is not the first thread with activation VoLTE and VoWIFI. But my thread will be more convenient and easier to understand.
ATTENTION ! ! ! These methods were only tested with OnePlus 7 Pro. Not 7,8,910 Series.
ONLY ONEPLUS 7 PRO MODEL ! ! ! So please don't PM me if you haven't OnePlus 7 Pro.
OnePlus devices support all the most modern services that are offered to their subscribers by mobile operators around the world.
This guide is universal method for VoLTE & VoWiFi activation on both OOS and custom ROMs. Root is needed in some cases.
Before using this guide, please read second post in this article. It is important to understand which firmware is used in your ROM.
Also you can check Carrier List in third post.
Spoiler: New method (A12/A12.1/A13 ROM)(OOS11/OOS12 FW)
Download and install QPST and Qualcomm Drivers from releases page on GitHub
Download and install USB Gadget Tool from https://f-droid.org/ru/packages/net.tjado.usbgadget/
Plug-in your phone into PC, and don't forget to enable MTP and ADB
Open USB Gadget Tool and turn on next modes (if they turned off) :
( cser.dun.O , diag.diag, diag.diag.mdm , ffs.adb , gsi.dpl , gsi.rmnet , qdss.qdss , qdss.qdss.mdm )
Further actions depending on what you need: EFS or PDC
IMPORTANT!!! Don't forget to disconnect and reboot your OP7Pro after using any mode (If you want use both EFS and PDC, then use PDC, after that, disconnect and reboot OP7Pro, then repeat all steps from beginning for EFS)
Spoiler: For EFS Explorer
Excecute " setprop sys.usb.config diag,diag_mdm,qdss,qdss_mdm,serial_cdev,dpl,rmnet,adb " in adb shell with su (root):
adb shell su setprop sys.usb.config diag,diag_mdm,qdss,qdss_mdm,serial_cdev,dpl,rmnet,adb
Then check that all COM ports are added in QPST Configuration, one of these ports will be SDM855 - our device
Open EFS Explorer
Profit
End of guide for EFS Explorer
Spoiler: For PDC Tool
Excecute " setprop sys.usb.config diag,serial_cdev,rmnet,adb " in adb shell with su (root):
adb shell su setprop sys.usb.config diag,serial_cdev,rmnet,adb
Then after 10 seconds disable in USB Gadget Tool app next modes : "diag.diag and diag.diag.mdm"
After that open PDC Tool
Profit
End of guide for PDC Tool
Depending on what you need follow the 7-13 p. from Old Method instructions. This new method was tested on crDroid 8.
Spoiler: Old method (OOS 9-10 ROM and FW only)
OnePlus devices support all the most modern services that are offered to their subscribers by mobile operators around the world. To enable and configure IMS services requires a minimum of time and effort, it is very rare now, for which many thanks to OnePlus. Also doesn't need root
On OOS 9.5.9 and higher after entering the code *#800# and *#801# select "EngineerMode"
Instruction:
1. You need to activate IMS service on your Carrier side. On some carrier IMS is activated by default.
2. Install Qualcomm QPST Diag port x64 / QPST 2.7.474 software on your computer (links below)
Important: there should be no other Qualcomm drivers on the computer, disable them, otherwise error messages will appear!
3. Enter * # 800 # in the stock dialer, and then click oneplus Logkit - next - Function Switch - next - activate VoLTE switch, VoWifi switch and VT switch.
Then reboot the device and turn on VoLTE and VoWIFI in the settings of your SIM card (“Settings” –– “WiFi and Internet” ––––– “SIM-card and network” “VoLTE and Calls via WI-FI”). If the switches “VoLTE switch”, “VoWifi switch”, “VT switch” are NOT available in your “oneplus Logkit”, install this version
OEMLogKit.apk or OEMLogKit_1.0-1.apk
and EngineeringMode.apk
4. Now you need to connect your mobile phone to the computer via the “USB cable”.
5. Open the dialer enter this code *#801#.
6. After entering the code correctly, a new menu appears, turn on there "Full-port switch"
7. Now you start the program on your PC: “PDC” from the QPST software package and select your smartphone from the list of connected devices.
8. Right-click on the line “Oversea-Commercial_DS” in the section of the “Deactivate” menu that opens, select “Sub0” and “Sub1”.
9. Next, in the list of available profiles, select "Profile that will be good for your country and Carrier, check the list below", right-click on it and in the section of the menu that opens, select "SetSelectedConfig", "Sub0" and "Sub1".
10. Now again click on the profile line “Profile that will be good for your country and Carrier, check the list below” and below in the program window click the “Activate” button.
11. Now go back to the MENU of item 6 of this menu instruction. Turn off the item "Full-port switch", reboot your smartphone and the VoLTE or VoWiFi logo should be displayed in the status bar.
12. ViLTE (video over LTE) may or may not work, depending on the services of your mobile Carrier.
13. If u have an issue with VoLTE (may go in default setting after reboot - DC Commercial), then do next after step 8 : Click on “Oversea-Commercial_DS” again and below click on the “Remove” button.
If you want to activate VoLTE on stock OOS 11 ROM then you can use this simple guide.
If you have any Questions or issues related to my guide you can ask me on Telegram (link in my profile). Before asking me on Telegram please follow ALL steps without exception!
Firmware explanation:
Activation method depends on what firmware you have installed. Not OS (crDroid, LineageOS, Pixel Experience), but firmware (fw).
There are 4 versions of fw for OnePlus 7 Pro for now : | OOS 9 | OOS 10 | OOS 11 | OOS 12 |
If you have installed OOS 9 or OOS 10 then use Old method from top post.
If you have installed OOS 11 or OOS 12 then use New method from top post.
You can ask developer about what version of firmware installed on your custom ROM.
Carrier choice:
Spoiler: Carrier list
Australia - Optus - Telefonica_UK_Commercial
Australia - Telstra - Telefonica_UK_Commercial
Belgium - Orange - Telefonica_UK_Commercial
Belgium - Proximus - India_Volte_Vodafone
Brazil - Claro - Telefonica_UK_Commercial
Brazil - TIM - Volte_OEM_lab
Canada - Bell - Telefonica_UK_Commercial
Canada - Telus - Telefonica_UK_Commercial
Czech Republic - O2 - Telefonica_UK_Commercial
France - Orange - Orange_Commercial_France
France - Orange - Telefonica_UK_Commercial
France - RED SFR - Telefonica_UK_Commercial
Greece - Cosmote - H3G_Denmark_Commercial
Israel - 012 mobile - Telefonica_UK_Commercial
Israel - Partner - Telefonica_UK_Commercial
Kenya - Faiba - ROW_Commercial
Ksa Saudi Arabia - Zain ksa - Germany
Ksa Saudi Arabia - Zain ksa - India_Volte_Vodafone
Ksa Saudi Arabia - Zain ksa - Telefonica_UK_Commercial
Mexico - ALTAN - Telefonica_UK_Commercial
Netherlands - KPN - Norway Telia Commercial
Norway - Telenor - India_Volte_Vodafone
Poland - Orange - DT_Poland_Commercial
Poland - Plus Polkomtel - ROW_Commercial
Romania - Orange RO - India_Volte_Vodafone
Romania - Vodafone RO - India_Volte_Vodafone
Russia - All Carriers - Telia_Finland
Russia - MegaPhone Region not Moscow - Volte_OEM_lab
Slovakia - Orange - DT_Slovakia_Commercial
Sri Lanka - Dialog - India_Volte_Vodafone
Sri Lanka - MobitelSriLankaTelecom and Dialog - Telefonica UK, Commercial
Switzerland - Wingo (Swisscom) - Netherlands_VoLTE_Vodafone
Turkey - TurkTelekom - India_Volte_Vodafone
If you could not find your country or operator, then there are two options:
1. Try to use: India_Volte_Vodafone or Telefonica_UK_Commercia . Thees are most common modes.
2. Try to search your country and operator here and here
Also if you enabled VoLTE with some config that doesn't represented in the list, then please leave a message in this thread in next format:
Country - Carrier - Mode
ex.
Russia - MTS - Telia_Finland
This will be helpful for other members of xda community. Also i update list of carriers from time to time.
Check here, did a video guide in English on the same.
Cheers
Doesn't work on custom roms and doesn't even look like you tested this on Android 10 at all.... Which is what most people are using now..
Blackcrane said:
Doesn't work on custom roms and doesn't even look like you tested this on Android 10 at all.... Which is what most people are using now..
Click to expand...
Click to collapse
Working fine on PE. It doesn't work, if custom ROM didn't support it
Blackcrane said:
Doesn't work on custom roms and doesn't even look like you tested this on Android 10 at all.... Which is what most people are using now..
Click to expand...
Click to collapse
Once you enabled using this method u don't need to do same all over on custom ROM, enable Volte option and restart the ROM and it should works.
And working fine on Android 10 as well.
Working on both tested myself.
Thank you for the guide, is it necessary to actually perform step number 8? Seems so permanent;
9. Now click on “Oversea-Commercial_DS” again and below click on the “Remove” button.
And I see per the previous guide;
https://forum.xda-developers.com/oneplus-7-pro/help/force-enable-volte-vowifi-t3934227
"Click on Oversea-Commercial_DS again and click on remove -- DO NOT CLICK REMOVE, JUST DE-ACTIVATE IT - your settings stick after a reboot, so no longer need to remove the profile (at least on my device my profiles stick, also makes it easier to go back to default)"
cantenna said:
Thank you for the guide, is it necessary to actually perform step number 8? Seems so permanent;
9. Now click on “Oversea-Commercial_DS” again and below click on the “Remove” button.
And I see per the previous guide;
https://forum.xda-developers.com/oneplus-7-pro/help/force-enable-volte-vowifi-t3934227
"Click on Oversea-Commercial_DS again and click on remove -- DO NOT CLICK REMOVE, JUST DE-ACTIVATE IT - your settings stick after a reboot, so no longer need to remove the profile (at least on my device my profiles stick, also makes it easier to go back to default)"
Click to expand...
Click to collapse
Thank u! Added in end of guide (optionally)! Btw i also sometimes have this issue, but on latest beta - just deactivate is good for me too
how the IMS service is activated?
efx_d3 said:
how the IMS service is activated?
Click to expand...
Click to collapse
U need to activate it on ur Carrier side. On most Carriers it's enabled by default.
jimmy123322 said:
U need to activate it on ur Carrier side. On most Carriers it's enabled by default.
Click to expand...
Click to collapse
So, do I need to speak to my operator and request that they activate this service?
as this did not work for me, I think this IMS service is not active in my operator...
when i update i lose these settings
efx_d3 said:
So, do I need to speak to my operator and request that they activate this service?
as this did not work for me, I think this IMS service is not active in my operator...
Click to expand...
Click to collapse
Idk, maybe yes
Not working with Bell Canada
I have followed your handy guide with one issue, I can't get it to work for Bell Canada. I have tied multiple varieties. I initially used the Telefonica_UK_Commercial that is listed and made calls drop after 30 sec or so. When I used *#*#4636#*#* and selected the option in the top right and then IMS it showed VoLTE as inactive even though the symbol was present. I tried ATT_VoLTE and it shows VoLTE but no VoWIFI. I'm not sure if it worked or not. IMS showed VoLTE as active. I didn't really leave it to try it as I can't chance more dropped calls. I went back to the Oversea-Commercial_DS as it works for calls. I have contacted my carrier to ensure the IMS settings for VoLTE and VoWiFi are enabled on the carrier side.
2 things, first is you should add to your guide to ensure USB Debugging is enabled as I found it wouldn't work without.
2nd is when I make calls I have the HD symbol while calling, does this not mean it is using VoLTE already even without the symbol present in the status bar? Seems to be conflicting info regarding the HD calls symbol while actually in a call.
Lastly, not going to lie, the VoLTE and VoWiFi symbols are a little obnoxious on the stock ROM. Most other phones are fairly small or just an add on to the existing phone symbol.
Any suggestions for Canadian carriers to verify/ensure this is working correctly?
At step 7, when i open the app. my device is not listed.
jimmy123322 said:
Yes, yes, I know that this is not the first thread with activation VoLTE and VoWIFI. But my thread will be more convenient and easier to understand.
OnePlus devices support all the most modern services that are offered to their subscribers by mobile operators around the world. To enable and configure IMS services requires a minimum of time and effort, it is very rare now, for which many thanks to OnePlus. Also doesn't need root
On OOS 9.5.9 and higher after entering the code *#800# and *#801# select "EngineerMode"
Instruction:
1. You need to activate IMS service on your Carrier side. On some carrier IMS is activated by default.
2. Install Qualcomm QPST Diag port x64 / QPST 2.7.474 software on your computer (links below)
Important: there should be no other Qualcomm drivers on the computer, disable them, otherwise error messages will appear!
3. Enter * # 800 # in the stock dialer, and then click oneplus Logkit - next - Function Switch - next - activate VoLTE switch, VoWifi switch and VT switch.
Then reboot the device and turn on VoLTE and VoWIFI in the settings of your SIM card (“Settings” –– “WiFi and Internet” ––––– “SIM-card and network” “VoLTE and Calls via WI-FI”). If the switches “VoLTE switch”, “VoWifi switch”, “VT switch” are NOT available in your “oneplus Logkit”, install this version
OEMLogKit.apk or OEMLogKit_1.0-1.apk
and EngineeringMode.apk
4. Now you need to connect your mobile phone to the computer via the “USB cable”.
5. Open the dialer enter this code *#801#.
6. After entering the code correctly, a new menu appears, turn on there "Full-port switch"
7. Now you start the program on your PC: “PDC” from the QPST software package and select your smartphone from the list of connected devices.
8. Right-click on the line “Oversea-Commercial_DS” in the section of the “Deactivate” menu that opens, select “Sub0” and “Sub1”.
9. Next, in the list of available profiles, select "Profile that will be good for your country and Carrier, check the list below", right-click on it and in the section of the menu that opens, select "SetSelectedConfig", "Sub0" and "Sub1".
10. Now again click on the profile line “Profile that will be good for your country and Carrier, check the list below” and below in the program window click the “Activate” button.
11. Now go back to the MENU of item 6 of this menu instruction. Turn off the item "Full-port switch", reboot your smartphone and the VoLTE or VoWiFi logo should be displayed in the status bar.
12. ViLTE (video over LTE) may or may not work, depending on the services of your mobile Carrier.
13. If u have an issue with VoLTE (may go in default setting after reboot - DC Commercial), then do next after step 8 : Click on “Oversea-Commercial_DS” again and below click on the “Remove” button.
List of Carriers and Mode presented below
List of Carriers and Mode:
Greece - Cosmote - H3G_Denmark_Commercial
Czech Republic - O2 - Telefonica_UK_Commercial
Belgium - Orange - Telefonica_UK_Commercial
France - Orange - Telefonica_UK_Commercial
France - Orange - Orange_Commercial_France
France - RED SFR - Telefonica_UK_Commercial
Turkey - TurkTelekom - India_Volte_Vodafone
Norway - Telenor - India_Volte_Vodafone
Belgium - Proximus - India_Volte_Vodafone
Netherlands - KPN - Norway Telia Commercial
Brazil - Claro - Telefonica_UK_Commercial
Switzerland - Wingo (Swisscom) - Netherlands_VoLTE_Vodafone
Kenya - Faiba - ROW_Commercial
Australia - Optus - Telefonica_UK_Commercial
Sri Lanka - Dialog - India_Volte_Vodafone
Canada - Telus - Telefonica_UK_Commercial
Canada - Bell - Telefonica_UK_Commercial
Romania - Vodafone RO - India_Volte_Vodafone
Romania - Orange RO - India_Volte_Vodafone
Mexico - ALTAN - Telefonica_UK_Commercial
Russia - All Carriers - Telia_Finland
Russia - MegaPhone Region not Moscow - Volte_OEM_lab
If you could not find your country or operator, then there are two options:
1. Try to use: India_Volte_Vodafone or Telefonica_UK_Commercia . Thees are most common modes.
2. Try to search your country and operator here and here
Also if u enable VoLTE with some config, then please leave a message in this thread in next format:
Country - Carrier - Mode
ex.
Russia - MTS - Telia_Finland
This will be helpful for other members of xda community. Also i will add new config weekly.
App for checking VoLTE on GP Store
Big thanks for @dagoban and @jamal2367 for writing instructions and 4pda.ru for updating some info
Original thread - LINK
If i have any Questions u can ask me on Telegram (link in my profile)
Click to expand...
Click to collapse
Help
vladvlad12 said:
Help
Click to expand...
Click to collapse
Check your drivers at PC. Phone must be shown as COM port.
jimmy123322 said:
Check your drivers at PC. Phone must be shown as COM port.
Click to expand...
Click to collapse
It is not, just that
vladvlad12 said:
It is not, just that
Click to expand...
Click to collapse
2. Install Qualcomm QPST Diag port x64 / QPST 2.7.474 software on your computer (links below)
Important: there should be no other Qualcomm drivers on the computer, disable them, otherwise error messages will appear!