[ROM][UNOFFICIAL][12][OTA][OSS] LineageOS 19.1 for Galaxy S9/S9+ Exynos - Samsung Galaxy S9 & S9+ Cross Device Development

[ROM][UNOFFICIAL][12][OTA][OSS] LineageOS 19.1 for Galaxy S9/S9+ Exynos - Samsung Galaxy S9 & S9+ Cross Device Development

Requirements:
Latest firmware
Pre-Install Instructions
Warning: The following instructions will unlock the bootloader and wipe all userdata on the device.
Connect the device to a Wi-Fi network.
Enable Developer Options by pressing the “Build Number” option in the “Settings” app within the “About” menu
From within the Developer options menu, enable OEM unlock.
Power off the device, and boot it into download mode:
With the device powered off, hold Volume Down + Volume Up and connect USB cable to PC.
Now, click the button that the onscren instructions coorelate to “Continue” and/or “Unlock Bootloader”.
Your device will reboot, you may now unplug the USB cable from your device.
The device will demand you format userdata, please follow the onscreen instructions to do so.
Run through Android Setup skipping everything you can, then connect the device to a Wi-Fi network.
Re-enable Development settings by clicking the “Build Number” option 10 times, in the “Settings” app within the “About” menu, and verify that “OEM Unlock” is still enabled in the “Developer options” menu.
Installing LineageOS for the first time
Flash lineage recovery
Only the provided lineage recovery will be supported,
using TWRP might result in a possible data loss!!
If using Odin rename the lineage recovery image for your model to recovery.img and add it to a .tar archive using e.g 7zip.
If using Heimdall use: heimdall flash --RECOVERY recovery.img --no-reboot
Boot lineage recovery
IMPORTANT: Do not boot into system again before booting recovery, or system will restore stock recovery!
If using Odin untick auto-reboot before flashing.
After flashing reboot by pressing Volume Down and Power for approximately 7 seconds,
immediately hold Volume Up, Bixby and Power to boot recovery
boot recovery via Volume Up, Bixby and Power.
Factory reset using Factory reset -> Format data/factory reset
Warning: Unlike TWRP this will also erase internal storage!
Sideload LineageOS by enabling sideload via Apply Update -> Apply from ADB
Then run adb sideload <path to your lineage.zip> on your PC
Optional:
Sideload GApps and magisk by repeating above step
with their zip/apk

This build does not use the stock vendor, instead it's built on top of new trees which have been worked on for some time. The source is on our github, link in OP. You also get a few neat features like fingerprint gestures, and bixby button that actually works with both normal and long press.
I suggest using OpenCamera since stock one has some issues with flash.
These builds are signed with our release keys.
star2lte and crownlte support will come a bit later as i don't own the devices, but they will be supported eventually.
THESE BUILDS HAVE FORCE ENCRYPTION ENABLED, AND ONLY LINEAGE RECOVERY IS SUPPORTED. THESE THINGS WILL NOT CHANGE. IF YOU DON'T USE LINEAGE RECOVERY, AND SUFFER FROM DATA LOSS, DON'T COMPLAIN HERE.

Build uploaded, enjoy

Woah!!! Nice

How did you get OTA to work, I wanna try it too

nice
will try
been trying your work in PE, congrats on that and now curious to try this rom,
if I understood correctly this is your work along with Rob now?
Keep up the good work and thanks once again for reviving our devices

does LTE is supported in this ROM ?

quakze said:
does LTE is supported in this ROM ?
Click to expand...
Click to collapse
LTE/4G works with this ROM

Hey, thank you very much for this ROM, it's really smooth! Everything works except my second SIM.
For the first release this is pretty nice... and ... this is my first experience with Android 12 / LineageOS 19

star2lte build is up as well, find it at the link in the OP

BIG THANKS to the devs... NOW my S9+ will get a new life.
Edit: Did a test with 2 SIMs and only SIM1 is detected - no SIM2 so far... the Rest is really great work!!!

Great Job, Fresh install and my S9+ is (almost) Brand New!
I installed it with Samsung tool Odin recovery Lineage
Installing the rom with a sd card in de recovery, no sideload use! That works great!
Keep up the great work!

Razuuu said:
LTE/4G works with this ROM
Click to expand...
Click to collapse
does not work, JIO which works on only VoLTE.
When accessing the *#*#4636#*#* service menu (Testing) → Phone information, all the toggles for: VoLTE, Video Calling, WiFi Calling, EAB are off and greyed out (unable to be toggled on).
From the ... drop menu → IMS Service Status:
IMS Registration: Not Registered
Voice over LTE: Unavailable
Voice over WiFi: Unavailable
Video Calling: Unavailable
UT Interface: Unavailable

quakze said:
does not work, JIO which works on only VoLTE.
When accessing the *#*#4636#*#* service menu (Testing) → Phone information, all the toggles for: VoLTE, Video Calling, WiFi Calling, EAB are off and greyed out (unable to be toggled on).
From the ... drop menu → IMS Service Status:
IMS Registration: Not Registered
Voice over LTE: Unavailable
Voice over WiFi: Unavailable
Video Calling: Unavailable
UT Interface: Unavailable
Click to expand...
Click to collapse
See my picture

Feels damn fast but no second sim in S9

Can someone tell me why Lineageos Recovery is the only way to go?
And does it bring the same features as TWRP or is it really based for LineageOS?
Thanks for the info!
Since Magisk Guru is working for Google I hear a lot of complains about Magisk 24.
Does anyone have some good experience with Magisk 24 and rooting and hiding?

Mr-Dutch said:
Can someone tell me why Lineageos Recovery is the only way to go?
And does it bring the same features as TWRP or is it really based for LineageOS?
Thanks for the info!
Since Magisk Guru is working for Google I hear a lot of complains about Magisk 24.
Does anyone have some good experience with Magisk 24 and rooting and hiding?
Click to expand...
Click to collapse
I don't know the reasons (time/effort?), but TWRP doesn't support encrypted partitions which this rom forces.

Is there a list of working/non working features in this rom?

I just wanna say : This ROM is amazing, is blazing fast, super easy install flow, no problems at all; I have no seconds SIM to test however, in my phone the "App Switcher" from the bottom nav bar isn't working, I'm the only one? Keep the amazing work @DeHuMaNiZeD

Related

[ROM][OFFICIAL][pioneer][9] LineageOS 16.0

How to flash latest firmware
[ protip: 20191010+ builds require 50.2 FW (at least bluetooth, dsp, modem from it) If you're still running 50.1 you can flash this package in TWRP: https://androidfilehost.com/?fid=4349826312261716572 unless you're fine with having partially broken audio and broken Egistec fingerprint sensor ;3 ]
However if you want to flash whole firmware package onto both slots, you can follow the guide below:
1. Download latest firmware with XperiFirm.
NOTE: When using mono XperiFirm will fail to unpack the firmware, you can do it manually using following commands:
Code:
for f in FILE_*; do unzip $f; done
unzip boot.zip -d boot
2. Go to the directory where the firmware got downloaded to and remove following files:
- boot_X-FLASH-ALL-18AE_0x00.hash
- boot_X-FLASH-ALL-18AE.sin
- persist_X-FLASH-ALL-18AE_0x00.hash
- persist_X-FLASH-ALL-18AE.sin
- system_other_X-FLASH-ALL-18AE_0x00.hash
- system_other_X-FLASH-ALL-18AE.sin
- system_other_X-FLASH-ALL-9B8D_0x00.hash
- system_X-FLASH-ALL-18AE_0x00.hash
- system_X-FLASH-ALL-18AE.sin
- system_X-FLASH-ALL-9B8D_0x00.hash
- userdata_X-FLASH-CUST-18AE.sin
- vendor_X-FLASH-ALL-18AE_0x00.hash
- vendor_X-FLASH-ALL-18AE.sin
- vendor_X-FLASH-ALL-9B8D_0x00.hash
3. Turn off your phone, hold vol dn and plug in the USB cable, the screen should be off and green LED lit.
4. Run Newflasher, it'll flash entire FW to your current slot then unplug the USB cable and power on your phone.
5. Turn off your phone, hold vol up and plug in the USB cable, the screen should be off and blue LED lit.
6. Enter this command: `fastboot getvar current-slot`, it should return something like this:
current-slot: _b
Finished. Total time: 0.001s
7. Now switch to the opposite slot by entering command: `fastboot set_active a` if the current slot is `_b` or `fastboot set_active b` if its `_a`, you should see this:
Setting current slot to 'a'...
OKAY [ 0.012s]
Finished. Total time: 0.014s
or
Setting current slot to 'b'...
OKAY [ 0.012s]
Finished. Total time: 0.014s
8. Unplug usb cable and repeat steps: 3, 4
9. Profit?

Jozinek said:
Reccomended Gapps for this build?
Click to expand...
Click to collapse
dunno, just try any gapps you want.
btw I recommend downloading new build, I fixed wvm and camera no longer takes an eternity to launch.

Does it use 4.9 kernel or 4.4?

Casserole said:
Does it use 4.9 kernel or 4.4?
Click to expand...
Click to collapse
4.4

Unable to boot?
hello, thanks for this build. I have flashed the latest build in TWRP but for some reason keep getting thrown back into TWRP after flashing everything and rebooting. I'm not entirely sure why this is occurring.

techboy11 said:
hello, thanks for this build. I have flashed the latest build in TWRP but for some reason keep getting thrown back into TWRP after flashing everything and rebooting. I'm not entirely sure why this is occurring.
Click to expand...
Click to collapse
Stop flashing twrp lol.

LuK1337 said:
Stop flashing twrp lol.
Click to expand...
Click to collapse
I did not flash TWRP at first, but it still threw me into the default Lineage/Android recovery. Flashing TWRP or not doesn't make a difference for me.
Edit: I should mention the recovery screen I get without flashing TWRP says that my data is corrupt and I should try factory resetting or try booting again. Doing a factory reset option brings it to the same screen again.

techboy11 said:
I did not flash TWRP at first, but it still threw me into the default Lineage/Android recovery. Flashing TWRP or not doesn't make a difference for me.
Edit: I should mention the recovery screen I get without flashing TWRP says that my data is corrupt and I should try factory resetting or try booting again. Doing a factory reset option brings it to the same screen again.
Click to expand...
Click to collapse
Try fastboot -w reboot.

LuK1337 said:
Try fastboot -w reboot.
Click to expand...
Click to collapse
That worked. Now boots. Thanks for your help!

Thanks dude

Thanks for your work.
Front camera picture is upside down and i am unable to make photos with it.
EDIT: Works with Footej camera!

Schritti said:
Thanks for your work.
Front camera picture is upside down and i am unable to make photos with it.
EDIT: Works with Footej camera!
Click to expand...
Click to collapse
Yeah it's a temporary camera app until Snap is back so I won't bother figuring out what's wrong with it.

Do you publish changelog for new versions somewhere? Would be nice to know the changes.
Sent from my Sony H3113 using XDA Labs

Schritti said:
Do you publish changelog for new versions somewhere? Would be nice to know the changes.
Sent from my Sony H3113 using XDA Labs
Click to expand...
Click to collapse
No, I don't.

please fix screen mirroring function
i have found this
https://www.youtube.com/watch?v=1wIM67kVVL8
instructions:
1. change the following code line in /system/etc/wfdconfig.xml:
ContentProtection
Valid1/Valid
to
ContentProtection
Valid0/Valid
2. then add a line in /system/build.prop after "persist.debug.wfd.enable=1"
persist.debug.wfd.appmonitoring=1
3. and then from ADB
"adb shell su setprop persist.debug.wfd.appmonitoring 1"
4. reboot your phone and it will work
thanks

zsolt64555 said:
please fix screen mirroring function
i have found this
https://www.youtube.com/watch?v=1wIM67kVVL8
instructions:
1. change the following code line in /system/etc/wfdconfig.xml:
ContentProtection
Valid1/Valid
to
ContentProtection
Valid0/Valid
2. then add a line in /system/build.prop after "persist.debug.wfd.enable=1"
persist.debug.wfd.appmonitoring=1
3. and then from ADB
"adb shell su setprop persist.debug.wfd.appmonitoring 1"
4. reboot your phone and it will work
thanks
Click to expand...
Click to collapse
yeah i need to figure out a way to test it without leaving my room first.

LuK1337 said:
yeah i need to figure out a way to test it without leaving my room first.
Click to expand...
Click to collapse
THX your hard work!
Keep it Up.

Hi
Everything is working on latest build what i probed,
only the video playback is lagging
the smaller resolution is ok, but the HD and full HD playing is lagging with youtube app, and also in browser.

zsolt64555 said:
Hi
Everything is working on latest build what i probed,
only the video playback is lagging
the smaller resolution is ok, but the HD and full HD playing is lagging with youtube app, and also in browser.
Click to expand...
Click to collapse
i cant reproduce that, on youtube and twitch with 1080p 60fps everything is smooth, no lags and no glitches

[ROM][OFFICIAL][voyager][11] LineageOS 18.1

[ protip: These builds require 50.2 FW (at least bluetooth, dsp, modem from it) If you're still running 50.1 you can flash this package in TWRP: https://androidfilehost.com/?fid=4349826312261777345 unless you're fine with having partially broken audio and broken Egistec fingerprint sensor ;3 ]
However if you want to flash whole firmware package onto both slots, you can follow the guide below:
1. Download latest firmware with XperiFirm.
NOTE: When using mono XperiFirm will fail to unpack the firmware, you can do it manually using following commands:
Code:
for f in FILE_*; do unzip $f; done
unzip boot.zip -d boot
2. Go to the directory where the firmware got downloaded to and remove following files:
- boot_X-FLASH-ALL-18AE_0x00.hash
- boot_X-FLASH-ALL-18AE.sin
- persist_X-FLASH-ALL-18AE_0x00.hash
- persist_X-FLASH-ALL-18AE.sin
- system_other_X-FLASH-ALL-18AE_0x00.hash
- system_other_X-FLASH-ALL-18AE.sin
- system_other_X-FLASH-ALL-9B8D_0x00.hash
- system_X-FLASH-ALL-18AE_0x00.hash
- system_X-FLASH-ALL-18AE.sin
- system_X-FLASH-ALL-9B8D_0x00.hash
- userdata_X-FLASH-CUST-18AE.sin
- vendor_X-FLASH-ALL-18AE_0x00.hash
- vendor_X-FLASH-ALL-18AE.sin
- vendor_X-FLASH-ALL-9B8D_0x00.hash
3. Turn off your phone, hold vol dn and plug in the USB cable, the screen should be off and green LED lit.
4. Run Newflasher, it'll flash entire FW to your current slot then unplug the USB cable and power on your phone.
5. Reboot to recovery mode (both Lineage recovery and TWRP will work)
6. Flash https://androidfilehost.com/?fid=4349826312261712574
7. Profit?

First things first...Thank you!
Also, probably a noob question but, I am on 17.1 already, will I have to flash it via Lineage recovery or twrp to test it?
I suppose the update will only work when there is an official version.

hamirali said:
First things first...Thank you!
Also, probably a noob question but, I am on 17.1 already, will I have to flash it via Lineage recovery or twrp to test it?
I suppose the update will only work when there is an official version.
Click to expand...
Click to collapse
Official lineage recovery won't accept my dev-keys so you need to go with TWRP. I don't recommend trying to update data from 17.1 tho.

LuK1337 said:
Official lineage recovery won't accept my dev-keys so you need to go with TWRP. I don't recommend trying to update data from 17.1 tho.
Click to expand...
Click to collapse
I was able to flash Lineage 18, everything seems ok except that the SD card is not visible when in system, however can access it if removed and reinserted.
Can manage.

hamirali said:
I was able to flash Lineage 18, everything seems ok except that the SD card is not visible when in system, however can access it if removed and reinserted.
Can manage.
Click to expand...
Click to collapse
Are you on first or second build?

LuK1337 said:
Are you on first or second build?
Click to expand...
Click to collapse
Oops! first build. Didn't realise there was another. Btw can you please advise on the gapps version. Thanks!

hamirali said:
Oops! first build. Didn't realise there was another. Btw can you please advise on the gapps version. Thanks!
Click to expand...
Click to collapse
No idea about gapps, I don't have them on my current R devices.

LuK1337 said:
No idea about gapps, I don't have them on my current R devices.
Click to expand...
Click to collapse
Successfully flashed and running well without any issues. Thanks!

LuK1337 said:
No idea about gapps, I don't have them on my current R devices.
Click to expand...
Click to collapse
On the 4th build, all seems to be working fine, apart from a small issue that when making calls the dialling screen doesn't appear, but it does successfully place the call. The issue is when I want to close the call (hang up) as that screen hasn't loaded.
Can manage, as usually I just let the other person hang up. Receiving calls is fine.
Otherwise, great work!

hamirali said:
On the 4th build, all seems to be working fine, apart from a small issue that when making calls the dialling screen doesn't appear, but it does successfully place the call. The issue is when I want to close the call (hang up) as that screen hasn't loaded.
Can manage, as usually I just let the other person hang up. Receiving calls is fine.
Otherwise, great work!
Click to expand...
Click to collapse
This sounds like gapps issue. Make sure that phone app is set in Settings -> Apps & notifications -> Default apps.

LuK1337 said:
This sounds like gapps issue. Make sure that phone app is set in Settings -> Apps & notifications -> Default apps.
Click to expand...
Click to collapse
You were absolutely right...issue resolved. Thanks!

Currently on lineage-18.0-20201011 and enjoying the slide out volume panel and enhanced display size setting. Great!

Testing lineage-18.0-20201019 and all seems good. The only small issue I keep having is with the camera, it freezes.... but I do not use it that much anyway.

how to update lineage-18.0-20201019 on LineageOS 18.0 20201018 without deleting

jacky51 said:
how to update lineage-18.0-20201019 on LineageOS 18.0 20201018 without deleting
Click to expand...
Click to collapse
I am no expert, but I don't think we can at this moment update without deleting or wiping out. Usually it takes less than 30 mins for me to update, flash gapps and restore everything else. If you use WhatsApp a lot, remember to back it up.

I will wait for LineageOS 18.0 20201018 to work fine thanks

hamirali said:
I am no expert, but I don't think we can at this moment update without deleting or wiping out. Usually it takes less than 30 mins for me to update, flash gapps and restore everything else. If you use WhatsApp a lot, remember to back it up.
Click to expand...
Click to collapse
lol, just do the same thing as in initial installation except no wipes. Make sure to not skip rebooting to recovery between flashing Lineage and gapps.

LuK1337 said:
lol, just do the same thing as in initial installation except no wipes. Make sure to not skip rebooting to recovery between flashing Lineage and gapps.
Click to expand...
Click to collapse
OK, I was rebooting to recovery between flashing Lineage and gapps, but I was doing an initial wipe before flashing the newer build...

Everything works fine. Thanks for your work!

[ROM][UNOFFICIAL][12.1][DISCONTINUED] LineageOS 19.1 for Galaxy Tab S6 Lite Exynos

Requirements:
Any R based firmware installed on your device.
Pre-Install Instructions
Warning: The following instructions will unlock the bootloader and wipe all userdata on the device.
Connect the device to a Wi-Fi network.
Enable Developer Options by pressing the “Build Number” option in the “Settings” app within the “About” menu
From within the Developer options menu, enable OEM unlock.
Power off the device, and boot it into download mode:
With the device powered off, hold Volume Down + Volume Up and connect USB cable to PC.
Now, click the button that the onscren instructions coorelate to “Continue” and/or “Unlock Bootloader”.
Your device will reboot, you may now unplug the USB cable from your device.
The device will demand you format userdata, please follow the onscreen instructions to do so.
Run through Android Setup skipping everything you can, then connect the device to a Wi-Fi network.
Re-enable Development settings by clicking the “Build Number” option 10 times, in the “Settings” app within the “About” menu, and verify that “OEM Unlock” is still enabled in the “Developer options” menu.
Installing LineageOS for the first time
Flash lineage recovery
Only the provided lineage recovery will be supported,
using TWRP might result in a possible data loss!!
If using Odin rename the lineage recovery image for your model to recovery.img and add it to a .tar archive using e.g 7zip.
If using Heimdall use: heimdall flash --RECOVERY recovery.img --no-reboot
Boot lineage recovery
IMPORTANT: Do not boot into system again before booting recovery, or system will restore stock recovery!
If using Odin untick auto-reboot before flashing.
After flashing reboot by pressing Volume Down and Power for approximately 7 seconds,
immediately hold Volume Up and Power to boot recovery
IMPORTANT: As of OneUI 3 your device needs to be connected to a PC via USB cable in order to be able to
boot recovery via Volume Up, Bixby and Power.
Factory reset using Factory reset -> Format data/factory reset
Warning: Unlike TWRP this will also erase internal storage!
Sideload LineageOS by enabling sideload via Apply Update -> Apply from ADB
Then run adb sideload <path to your lineage.zip> on your PC
Optional:
Sideload GApps and magisk by repeating above step
with their zip/apk
Magisk
I strongly recommend to use Lygisk instead,
which is a fork of Magisk that aims to improve support for devices with FBE that can't (and shouldn't anyways!) decrypt userdata in recovery,
this will also fix OTAs getting stuck while having installed Magisk.

Features
SELinux enforcing
AES-256-XTS FBE encryption
Latest Linux 4.14.x kernel
Known issues
LineageOS specific features like livedisplay (for now)
You tell me

I am on your unofficial 18 and this just pop up in updater, is it safe to do OTA? Thanks for your efforts!

fzzt said:
I am on your unofficial 18 and this just pop up in updater, is it safe to do OTA? Thanks for your efforts!
Click to expand...
Click to collapse
Always follow this rule of thumb: it is never safe to dirty flash a completely different build on top of an older build (i.e. flashing 19.0 on top of 18.1, or 18.1 on top of 17.1, etc.). At best, you'll find yourself having random problems all over the place; at worst, the ROM will refuse to load. Best thing to do whenever going from one major release to another (or from one completely different ROM to another) is backup your apps and data, wipe data and caches and perform a clean flash, then restore your apps and data. It's a fair bit of work, to be sure, but it's the best way to avoid problems.

Sim card dont work, IMEI dont show, gapps cant install. Any ideas?

electro_vinyl said:
Sim card dont work, IMEI dont show, gapps cant install. Any ideas?
Click to expand...
Click to collapse
About the SIM issue, there's two things:
1. (more likely) You flashed the wrong build (gta4xlwifi instead of gta4xl) or in other words, flashed the WiFi only version firmware.
2.(Unlikely but could happen) You corrupted your baseband somehow as I had a similar situation with my Redmi Note 9 with a corrupted baseband so basically the IMEI was all zeros. That was also the reason why the SIM card didn't work.
You could try to install the original firmware with odin and check functionality and try again.
About the gapps issue
Did you install it for the correct architecture (arm64 not arm)?
Does it show error messages?

Macuway said:
About the SIM issue, there's two things:
1. (more likely) You flashed the wrong build (gta4xlwifi instead of gta4xl) or in other words, flashed the WiFi only version firmware.
2.(Unlikely but could happen) You corrupted your baseband somehow as I had a similar situation with my Redmi Note 9 with a corrupted baseband so basically the IMEI was all zeros. That was also the reason why the SIM card didn't work.
You could try to install the original firmware with odin and check functionality and try again.
About the gapps issue
Did you install it for the correct architecture (arm64 not arm)?
Does it show error messages?
Click to expand...
Click to collapse
With the latest build, it's all fixed!

Installed Lineage 19 last weekend on my P-610. You can flash the rom.zip, GApps and Magisk in Recovery from SD-card, so no need to sideload with adb. I have a problem with Google Playstore, it lags a lot (pending...) and installing an app like Gmail takes a long time. Now it even stopped working. Will try it later with NikGApps for Android S

Hi, it seems audio is not working.
It's just me?
Any help please.
M

minoltista said:
Hi, it seems audio is not working.
It's just me?
Any help please.
M
Click to expand...
Click to collapse
Are you on today's build already?
If so try again with that please - your device might be hw revision 9 which uses different audio drivers and wasn't supported in my kernel until today
Also could check the output of adb shell getprop ro.boot.revision to confirm it's rev 9

Linux4 said:
Are you on today's build already?
If so try again with that please - your device might be hw revision 9 which uses different audio drivers and wasn't supported in my kernel until today
Also could check the output of adb shell getprop ro.boot.revision to confirm it's rev 9
Click to expand...
Click to collapse
Just installed and it works! Thanks !!!

guys how do you flash this? I follow all the steps and when I do adb sideload <lineage os> it fails at 47%?????
error 21 log on the tab

langamer101 said:
guys how do you flash this? I follow all the steps and when I do adb sideload <lineage os> it fails at 47%?????
error 21 log on the tab
Click to expand...
Click to collapse
got it working guys. no need to help anymore.

Does anyone know why gboard force closes every time i try to install? I cleared all storage, played with permissions. Nothing worked.

First of all, I want to say thank to @Linux4 for this release Secondly, I want to ask comrads how to install MicroG on this build? If you can step by step, I'm new to custom firmware

how is newest recovery

Screenshots please

Working nicely, I'm currently getting a weird issue with the 2021-11-27 gta4xl build.
It's extremely weird but with quiet songs there's some kind of audio ducking going on.
Song it was most obvious on was Air - Bad and Sad 4.2 Vagabond Demo for example but it sounds like it's trying to cut out the audio or something.
Device was bought a few days ago so I'm guessing it'll be the latest hw revision.

lobotomite said:
Working nicely, I'm currently getting a weird issue with the 2021-11-27 gta4xl build.
It's extremely weird but with quiet songs there's some kind of audio ducking going on.
Song it was most obvious on was Air - Bad and Sad 4.2 Vagabond Demo for example but it sounds like it's trying to cut out the audio or something.
Device was bought a few days ago so I'm guessing it'll be the latest hw revision.
Click to expand...
Click to collapse
I have the same thing with any sound on the tablet This is especially noticeable when playing songs on spotify.

[ROM][UNOFFICIAL][13.0] LineageOS 20 for Galaxy Tab S6 Lite

Pre-Install Instructions
Warning: The following instructions will unlock the bootloader and wipe all userdata on the device.
Connect the device to a Wi-Fi network.
Enable Developer Options by pressing the “Build Number” option in the “Settings” app within the “About” menu
From within the Developer options menu, enable OEM unlock.
Power off the device, and boot it into download mode:
With the device powered off, hold Volume Down + Volume Up and connect USB cable to PC.
Now, click the button that the onscren instructions coorelate to “Continue” and/or “Unlock Bootloader”.
Your device will reboot, you may now unplug the USB cable from your device.
The device will demand you format userdata, please follow the onscreen instructions to do so.
Run through Android Setup skipping everything you can, then connect the device to a Wi-Fi network.
Re-enable Development settings by clicking the “Build Number” option 10 times, in the “Settings” app within the “About” menu, and verify that “OEM Unlock” is still enabled in the “Developer options” menu.
Installing LineageOS for the first time
Flash lineage recovery
Only the provided lineage recovery will be supported,
using TWRP might result in a possible data loss!!
If using Odin rename the lineage recovery image for your model to recovery.img and add it to a .tar archive using e.g 7zip.
If using Heimdall use: heimdall flash --RECOVERY recovery.img --no-reboot
Boot lineage recovery
IMPORTANT: Do not boot into system again before booting recovery, or system will restore stock recovery!
If using Odin untick auto-reboot before flashing.
After flashing reboot by pressing Volume Down and Power for approximately 7 seconds,
immediately hold Volume Up and Power to boot recovery
IMPORTANT: As of OneUI 3 your device needs to be connected to a PC via USB cable in order to be able to
boot recovery via Volume Up and Power.
Factory reset using Factory reset -> Format data/factory reset
Warning: Unlike TWRP this will also erase internal storage!
Sideload LineageOS by enabling sideload via Apply Update -> Apply from ADB
Then run adb sideload <path to your lineage.zip> on your PC
Optional:
Sideload GApps and magisk by repeating above step
with their zip/apk

Features
SELinux enforcing
AES-256-XTS FBE encryption
Known issues
VoLTE/VoWiFi
You tell me
Likely more

If we already have LOS 19.1 and recovery, do we still need to install the new recovery and factory reset?
edit: I renamed the new recovery image to recovery.img and then used 7zip to make recovery.tar and flashed it with Odin. But when I booted to recovery, all I got was a blank screen. Had to reflash the 19.1 recovery to get it back.

Linux4 said:
Requirements:
Any Q, R or S based firmware installed on your device.
Pre-Install Instructions
Warning: The following instructions will unlock the bootloader and wipe all userdata on the device.
Connect the device to a Wi-Fi network.
Enable Developer Options by pressing the “Build Number” option in the “Settings” app within the “About” menu
From within the Developer options menu, enable OEM unlock.
Power off the device, and boot it into download mode:
With the device powered off, hold Volume Down + Volume Up and connect USB cable to PC.
Now, click the button that the onscren instructions coorelate to “Continue” and/or “Unlock Bootloader”.
Your device will reboot, you may now unplug the USB cable from your device.
The device will demand you format userdata, please follow the onscreen instructions to do so.
Run through Android Setup skipping everything you can, then connect the device to a Wi-Fi network.
Re-enable Development settings by clicking the “Build Number” option 10 times, in the “Settings” app within the “About” menu, and verify that “OEM Unlock” is still enabled in the “Developer options” menu.
Installing LineageOS for the first time
Flash lineage recovery
Only the provided lineage recovery will be supported,
using TWRP might result in a possible data loss!!
If using Odin rename the lineage recovery image for your model to recovery.img and add it to a .tar archive using e.g 7zip.
If using Heimdall use: heimdall flash --RECOVERY recovery.img --no-reboot
Boot lineage recovery
IMPORTANT: Do not boot into system again before booting recovery, or system will restore stock recovery!
If using Odin untick auto-reboot before flashing.
After flashing reboot by pressing Volume Down and Power for approximately 7 seconds,
immediately hold Volume Up and Power to boot recovery
IMPORTANT: As of OneUI 3 your device needs to be connected to a PC via USB cable in order to be able to
boot recovery via Volume Up, Bixby and Power.
Factory reset using Factory reset -> Format data/factory reset
Warning: Unlike TWRP this will also erase internal storage!
Sideload LineageOS by enabling sideload via Apply Update -> Apply from ADB
Then run adb sideload <path to your lineage.zip> on your PC
Optional:
Sideload GApps and magisk by repeating above step
with their zip/apk
Click to expand...
Click to collapse
May I ask for screenshots? This is amazing work

HippoInWindow said:
May I ask for screenshots? This is amazing work
Click to expand...
Click to collapse
It appears the dev wants you to use Telegram for support and doesn't answer questions here in XDA. But I didn't get much support there either. When I asked what gapps to use, It just pointed to the Nikgapps site. But when I flashed the CORE version for T, Play Store didn't recognize the internet connection. Tried to revert to 19.1 and it wouldn't let me. Claimed it was a downgrade and not allowed. Had to flash the latest stock version via Odin, with all of the Samsung and Google bloat.

Well, I got it to work in spite of the lack of support. Had to use the OMNI version of Nikgapps instead to CORE. One little nit pick discovered so far. /Setup/System/Status Bar setting to change the battery icon to text and show percent doesn't work. But that is easy to live with.

lewmur said:
If we already have LOS 19.1 and recovery, do we still need to install the new recovery and factory reset?
edit: I renamed the new recovery image to recovery.img and then used 7zip to make recovery.tar and flashed it with Odin. But when I booted to recovery, all I got was a blank screen. Had to reflash the 19.1 recovery to get it back.
Click to expand...
Click to collapse
https://dl.linux4.de/lineageos/releases/gta4xlwifi/
LOS 20 recovery here. I do think we have to use same recovery version as the instructions say.
The image has been updated today and now I see the lineage OS 20.0 recovery.

xsw2 said:
https://dl.linux4.de/lineageos/releases/gta4xlwifi/
LOS 20 recovery here. I do think we have to use same recovery version as the instructions say.
The image has been updated today and now I see the lineage OS 20.0 recovery.
Click to expand...
Click to collapse
if flashed it with the old recovery but the zip check false and then you have to flash anyway
i check and the file size of both recovery where the same thought that is just for the ones that need it for flash for the first time

Just downloaden every thing with a AVG Antivirus alert.
For now I'll wait and maybe test later.
edit: the alert was from a know false positive.
For me better safe than sorry.

reef2009 said:
Just downloaden every thing with a AVG Antivirus alert.
For now I'll wait and maybe test later.
View attachment 5705853
Click to expand...
Click to collapse
Well I built that zip myself, I can assure you there's no malware.
BTW Antivirus apps on android are only a waste of resources.

Updated with September securitypatch and more lineage features

Is the changelog link broken? When I try it to see if I want to flash the latest version, it just times out.

lewmur said:
Well, I got it to work in spite of the lack of support. Had to use the OMNI version of Nikgapps instead to CORE. One little nit pick discovered so far. /Setup/System/Status Bar setting to change the battery icon to text and show percent doesn't work. But that is easy to live with.
Click to expand...
Click to collapse
You're not owed support by anyone. OP could flip off every user and **** off forever, but they'd still have done their work for the community. Thanks for the tips, though!

okno13 said:
You're not owed support by anyone. OP could flip off every user and **** off forever, but they'd still have done their work for the community. Thanks for the tips, though!
Click to expand...
Click to collapse
I didn't claim I was owed support. I merely stated that I didn't get any and that I was able to get it working in spite of that.

Device reboots after opening camera. Probably issues with camera hal

So far so good, except I cannot for the life of me get the Google keyboard to work...all other gapps are fine...

Well, the dev for this ROM has convinced me to sell my S6 and buy a newer tablet that has support here in XDA. Apparently, he will only offer support in Telegram because, in that app, he can ban anyone who disagrees with him. So, no support if you want, TWRP, Magisk, Nixgapps, custom kernels or anything else he doesn't like.

lewmur said:
Well, the dev for this ROM has convinced me to sell my S6 and buy a newer tablet that has support here in XDA. Apparently, he will only offer support in Telegram because, in that app, he can ban anyone who disagrees with him. So, no support if you want, TWRP, Magisk, Nixgapps, custom kernels or anything else he doesn't like.
Click to expand...
Click to collapse
What reason would we have to ban people who want support? He doesn't provide support for TWRP because it's a discontinued project and because it worked terribly on the tablet. That's like asking Samsung for help on a flip phone you bought in 1994 that's been discontinued for quite a while. I don't think I recall him actively rejecting people's technical support for Magisk, NikGapps, or Custom Kernels when I was in his Telegram, he only said that he recommends alternatives to Magisk and NikGapps. I don't know if you're writing this after you were banned but the only time he proactively rejected support in people's devices is when TWRP was in the equation.

{Mod edit: Quoted post has been deleted}
It is being actively supported by legacy devices that can't handle encryption and on ROMs made by unknowingly devs.
Also you were told multiple times that encryption is not an optional thing, especially on T. And some users do care about their data not being just accessible when the device gets stolen.

[OFFICIAL][zippo] LineageOS 20 (Android 13) for the Lenovo Z6 Pro

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
LineageOS is based on the Android Open Source Project with extra contributions from many people within the Android community. It can be used without any need to have any Google application installed. Linked below is a package that has come from another Android project that restores the Google parts. LineageOS does still include various hardware-specific code, which is also slowly being open-sourced anyway.
All the source code for LineageOS is available in the LineageOS Github repo. And if you would like to contribute to LineageOS, please visit our Gerrit Code Review.
Code:
#include
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
SUPPORTED DEVICES
- zippo (L78051)
HOW TO INSTALL LINEAGEOS WITH LINEAGE RECOVERY
Please NOTE! As of LineageOS 19.1? We do NOT support bootloader locked! You MUST unlock your bootloader to use this version!
- Make sure your phone is running firmware from at least CN 12.5.332. If not? Please download and install it via recovery. It can be flashed before the ROM
If you want to follow the official instructions for bootloader unlock? Please go to the LineageOS Wiki here:
https://wiki.lineageos.org/devices/zippo/install
If you want to preserve a locked bootloader? Download and follow the instructions in this zip and then follow the official wiki instructions but skip the bootloader unlock section.
HOW TO UPDATE LINEAGEOS WITH LINEAGE RECOVERY
Please follow the official instructions on the LineageOS Wiki here:
https://wiki.lineageos.org/devices/zippo/update
HOW TO INSTALL LINEAGEOS WITH TWRP
Please NOTE! As of LineageOS 19.1? We do NOT support bootloader locked! You MUST unlock your bootloader to use this version!
- Make sure your phone is running firmware from at least CN 12.5.332. If not? Please download and install it via recovery. It can be flashed before the ROM
- Download the LineageOS and firmware zips. (see Downloads)
- Boot into TWRP.
- Copy the downloaded zip files to the internal storage of the device.
- Perform a backup of your current ROM. (Optional)
- RECOMMENDED: Do a factory reset (clean wipe)! No support if you didn't! (Wipe Dalvik, system, cache and format data)
- NOTE: If coming from stock ROM? You MUST format data (Wipe > tap "Format Data" button > type "yes" > keyboard checkbox)
- Flash firmware and LineageOS zips.
- Optional: Install the Google Apps addon package. (see Downloads)
- Reboot to system.
HOW TO UPDATE LINEAGEOS WITH TWRP
- Download the LineageOS zip(s). (see Downloads)
- Copy the downloaded zip files to the internal storage of the device.
- Reboot to TWRP.
- Flash LineageOS. (Wiping Dalvik and Cache is optional, but recommended)
- Reboot to system.
MAIN DOWNLOADS
TWRP for zippo: Official
Lenovo Z6 Pro
Disclaimer:Team Win strives to provide a quality product. However, it is your decision to install our software on your device. Team Win takes no ...
twrp.me
Lineage:
- Official:
LineageOS Downloads
download.lineageos.org
- Unofficial:
Package lineage-20 - lineageos-for-zippo - OSDN
Package lineage-20 - lineageos-for-zippo #osdn
osdn.net
GOOGLE APPS (GAPPS) DOWNLOADS
- MindTheGapps:
http://downloads.codefi.re/jdcteam/javelinanddart/gapps
GOOGLE CAMERA (GCAM) DOWNLOADS
Google Camera:
Wichaya GCam APKs - Google Camera Port
Modified Google Camera app by Wichaya.
www.celsoazevedo.com
Recommended version:
https://www.celsoazevedo.com/files/android/google-camera/dev-wichaya/f/dl5/
Recommended config:
https://osdn.net/projects/lineageos-for-zippo/releases/76575
FIRMWARE DOWNLOADS
Minimum required versions:
- zippo (L78051) CN 12.5.365
https://osdn.net/projects/lineageos-for-zippo/releases/p17514
DEVELOPER RESOURCES
https://github.com/lenovo-sm8150/local_manifests/
GitHub - LineageOS/android_device_lenovo_sm8150-common
Contribute to LineageOS/android_device_lenovo_sm8150-common development by creating an account on GitHub.
github.com
GitHub - LineageOS/android_device_lenovo_zippo
Contribute to LineageOS/android_device_lenovo_zippo development by creating an account on GitHub.
github.com
GitHub - LineageOS/android_kernel_lenovo_sm8150
Contribute to LineageOS/android_kernel_lenovo_sm8150 development by creating an account on GitHub.
github.com
HOW TO CONTRIBUTE
Send your patches up for review: https://review.lineageos.org/
Read the guides on the LineageOS Wiki: https://wiki.lineageos.org/
Source Code: https://github.com/LineageOS
DONATIONS
Pay Marc Bourgoin using PayPal.Me
Go to paypal.me/ThEMarD85 and type in the amount. Since it’s PayPal, it's easy and secure. Don’t have a PayPal account? No worries.
www.paypal.com

KNOWN BUGS
Currently only works with bootloader unlocked
SafetyNet does not pass (Unfortunately, this is not possible as your SoC has hardware attestation... the workaround is to use unsupported mods like Magisk which tbh I haven't tried myself as I don't root my devices, but other users said that plus the SafetyNet Magisk mod works)
Fingerprint icon is too low compared to actual location of the scanner
Heyyo, allow me to introduce myself. I am Marc "ThE_MarD" Bourgoin and I maintain LineageOS and TWRP for the LeEco Le Max 2 (X2) and was crowdfunded a zippo which I will maintain LineageOS for (with selinux enforcing of course) and maybe assist with TWRP later. I also own a Motorola Edge 30 (dubai) which I maintain LineageOS for, Asus Zenfone 5z (Z01R), and I was also donated a Motorola Moto X4 (Payton) which I maintain LineageOS and TWRP for.
I'd like to take this moment to also thank anyone who donated to the crowdfunding campaign for my zippo! Without you? I wouldn't have this epic device in my hands to work on.
Also MAJOR thanks to Zhenxiang Chen (aka pasta_con_tonno, Lucchetto) for all the amazing work he has done on zippo.
Special thanks to Einar Gednochsson (aka kanstmablason, pete80pro) for organizing the crowdfunding campaign for my zippo and also a new one for KuranKaname so he can revamp our kernel.
Thanks also to hypnz, chema f, gawin and Lucky for also working in zippo and to HighwayStar who started the initial trees for heart (Lenovo z5 Pro GT) which zippo trees are based upon and Art_Chen for working on heart and zippo and also bringing us FOD Dimming and DC Dimming.
Thanks again to Zhenxiang and Chema f for figuring out and implementing the QFIL recovery and vbmeta while keeping the bootloader locked

Heyyo, LineageOS 20 official is out and the first build for zippo is up!

@ThE_MarD ,
Will you be including this commit the hardware fix/support for the camera (camera: Expose aux cameras in third party apps) from Chemas Evo build in your Lineage build? I'd rather not have google services installed to use GCAM in order to access the other lens' and the ZUI camera does not install correctly anymore for 13 (it did for 12, partially). There are other apps that don't rely on g-services that are able to access the hardware (HIDL?) switch to select which lens is used for image processing.

Heyyo @project_2501 , after checking with other devs about that commit and also how aux cameras are set up? I think for that we can just modify our props in the device tree tbh. The problem we currently have is we are limiting it to only a few app names. We could transition to an aux camera blacklist since there's probably only a handful of apps that would screw up (I can't remember if it was here or my Asus Zenfone 5z, but the Adobe Scan app would screw up and fail to initialize any camera) so we could just tackle a blacklist as crappy apps show up lol
As you can see here, we mainly expose aux cameras to a few apps and others have to essentially find out themselves like gcam mods
android_device_lenovo_sm8150-common/system.prop at lineage-20 · LineageOS/android_device_lenovo_sm8150-common
Contribute to LineageOS/android_device_lenovo_sm8150-common development by creating an account on GitHub.
github.com

@ThE_MarD ,
Will the blacklist instead of a whitelist be applied on the next scheduled build? Thank you for addressing it.

@project_2501 sorry not yet as I need to test it first and I haven't had time yet

Heyyo, lineage-20.0-20230122-UNOFFICIAL-zippo test build is going up! ! It has a new rebased kernel by MikeNG. Please test all functions. It also has a change to swap the aux camera allowed list to an aux camera exclude list to keep things easier and only exclude apps that don't play well with aux cameras so please test a lot of camera apps
Release lineage-20 lineage-20.0-20230122-UNOFFICIAL-zippo - lineageos-for-zippo - OSDN
Release lineage-20 lineage-20.0-20230122-UNOFFICIAL-zippo - lineageos-for-zippo #osdn
osdn.net
@project_2501 if you could please test this build. You can swap between unofficial and official builds at any time

Switching between the camera lens' works (still don't see 48mp for the main lens' resolution); install almost hanged on patching vendor which I found odd. Camera app believes there are six cameras for some odd reason and will crash if selecting the sixth camera, I'm guessing it's also referencing the video profile because it doesn't crash in video mode when selecting the sixth camera (dual lens for video or mixed up with front lens' maybe)? Can you provide a link to the source for the kernel?

@project_2501 which camera app are you trying btw?
Source code links are in the first post please check there

ThE_MarD said:
@project_2501 which camera app are you trying btw?
Source code links are in the first post please check there
Click to expand...
Click to collapse
Open Camera.
I'm unfamiliar with MikeNG and kernel modifications he may have committed when looking at the source code for the kernel, just wondering since you stated it was using a different kernel (than official LOS?).

@project_2501 oh, Open Camera does things a lot differently than other camera apps so tbh I don't think there's a way to configure it... So I'd recommend just sticking with Aperture or use a gcam mod... But from what you said Open Camera is now seeing more camera apps so the change in aux camera lists commit is working then?

@ThE_MarD , yes I can switch between all the lens'. System stability has not been jeopordized, the app will just crash if trying to process from the sixth camera ID. Do you remember what modes the ZUI camera app had? Was there a dual (both front and back camera) mode? Maybe the sixth profile is for the front camera and the app doesn't switch to it when cycling through the lens' (front camera can still be accessed with a different on screen UI switch anyways). The problem in itself is app related; regardless, the commit works and should be included in the next build for others like myself who enjoy a clean minimalist build with full access to the hardware.

Hi, i'm on firmware 11.0.405 ST.
Now i'm still waiting my SN from Lenovo to unlock bootloader.
Newbie question:
After installing TWRP --> Wipe > tap "Format Data" button > type "yes" > keyboard checkbox > Flash firmware CN 12.5.332 > reboot to recovery or reboot to system ?
Thanks a lot for the rom!

Heyyo @danz852, after doing the format data, flash firmware and flashing ROM? You can optionally install any addons (such as GApps) and then reboot to system or skip the addons and reboot to system.

ThE_MarD said:
Heyyo @danz852, after doing the format data, flash firmware and flashing ROM? You can optionally install any addons (such as GApps) and then reboot to system or skip the addons and reboot to system.
Click to expand...
Click to collapse
@ThE_MarD , thanks for the reply. Appreciated
I'm still waiting file from Lenovo to unlock bootloader.

Finally got the file to unlock bootloader.
I flashed twrp > shut down the phone > hold Volume Up + Power > but it cannot boot to recovery, only show fastboot/bootloader.
Then I tried I flashed twrp > shut down the phone > Volume Down + Power > fastboot mode > then i select recovery mode > phone restarted > only returned to fastboot mode again.
Any help to solve this problem? failed to flash twrp recovery.
Thanks in advance.

@danz852 just to check, you're flashing it to the recovery partition?
The TWRP website has the full instructions too
Lenovo Z6 Pro
Disclaimer:Team Win strives to provide a quality product. However, it is your decision to install our software on your device. Team Win takes no ...
twrp.me
Code:
fastboot flash recovery twrp.img
Otherwise you can try first via Lineage Recovery and follow the LineageOS wiki instructions
Install LineageOS on zippo | LineageOS Wiki
wiki.lineageos.org

Hi, thanks for fast reply.
Yes i'm flashing it to the recovery partition (fastboot flash recovery twrp.img). The result was success. But still cannot boot to twrp.
FYI: I'm using file from this https://club.lenovo.com.cn/thread-7839615-1-1.html to unlock the bootloader because at least until now i didn't receive unlock file from Lenovo.
I tried to flash twrp-3.7.0_12-0-zippo then tried Lineage recovery , flashing was success but still cannot boot to recovery.
After that flashed TWRP 3.4.0 by @mauronofrio. this one is working and boot to twrp recovery. I proceed with Wipe Dalvik, system, cache and format data. Then ADB sideload firmware CN 12.5.332. Continue with ADB sideload LineageOS found no problem with the installation the proceed reboot to System (it's written No OS Installed!), I keep continue to reboot to System anyway. It stuck at Lenovo Logo the restart by itself back to Lenovo logo again and so on.
Maybe because TWRP 3.4.0 is not working for Android 13.
Now I'm trying to sideload firmware L78051_CN_11_5_229_Q_Stable_recovery., because i think it will be working with TWRP 3.4.0 but the result is the same, end up with Lenovo logo then it restart by itself again and again.

danz852 said:
Hi, thanks for fast reply.
Yes i'm flashing it to the recovery partition (fastboot flash recovery twrp.img). The result was success. But still cannot boot to twrp.
FYI: I'm using file from this https://club.lenovo.com.cn/thread-7839615-1-1.htmll to unlock the bootloader because at least until now i didn't receive unlock file from Lenovo.
I tried to flash twrp-3.7.0_12-0-zippo then tried Lineage recovery , flashing was success but still cannot boot to recovery.
After that flashed TWRP 3.4.0 by @mauronofrio. this one is working and boot to twrp recovery. I proceed with Wipe Dalvik, system, cache and format data. Then ADB sideload firmware CN 12.5.332. Continue with ADB sideload LineageOS found no problem with the installation the proceed reboot to System (it's written No OS Installed!), I keep continue to reboot to System anyway. It stuck at Lenovo Logo the restart by itself back to Lenovo logo again and so on.
Maybe because TWRP 3.4.0 is not working for Android 13.
Now I'm trying to sideload firmware L78051_CN_11_5_229_Q_Stable_recovery., because i think it will be working with TWRP 3.4.0 but the result is the same, end up with Lenovo logo then it restart by itself again and again.
Click to expand...
Click to collapse
UPDATE:
Finally it worked out:
I'm still using TWRP 3.4.0. Copy firmware L78051_CN_11_5_229_Q_Stable_recovery to internal storage then flash it. Reboot to System. It said my phone partition is corrupted .
Then i reboot the phone to Fastboot mode. I checked bootloader is Locked > proceed with fastboot flash unlock sn.img > fastboot oem unlock-go > reboot to system. After enable USB debugging in Developer Option > reboot to recovery > Wipe Dalvik, system, cache and format data > flash CN 12.5.332 and LineageOS. > reboot to system > Finally it booted to Lineage.
I'm happy. Thanks again @ThE_MarD for the rom!!!

Database Develop

welcome