Hello all,
I just got my AT&T Tilt and love it so far, except for one major annoyance. When I press the power button, the device will turn the screen back on after a few seconds to a few minutes. The problem is when it's in my pocket, it can accidentally call people. My 8125 and 8525 did not experience this issue.
Any suggestions?
Thanks!
Button lock
It sounds as though the phone isn't set to lock all buttons except the power button when it is in standby. This happened to me last time I re-flashed my Wizard, and I couldn't figure out for ages why my battery was draining so quickly as well!
Settings > Buttons > Lock
Hmm, not seeing any option under Buttons or Lock. I do remember this setting from WM5. It does appear, however, that the buttons are not turning the phone on, it's just waking up even if I leave it on a desk.
You can add lock to the home screen
first press and hold the hang-up button so that it locks. Then just push the power button once. This puts it in standby.
There is a idle timeout for going on standby mode, but I can't find a setting to auto-lock.
JBHorne said:
When I press the power button, the device will turn the screen back on after a few seconds to a few minutes.
Click to expand...
Click to collapse
Are you paired to a Bluetooth device? I see similar behavior in my 8525 when in my car - the BT car kit does stuff which "wakes" the 8525
Richard
Try this leaving Google Maps On the Screen
Hi Guys,
I get this behavior when I have Google Maps running. It will even cycle the screen on and off a couple times.
nope and nope. just sitting on the today screen.
JBHorne said:
When I press the power button, the device will turn the screen back on after a few seconds to a few minutes.
Click to expand...
Click to collapse
I have the very same problem.
However, my girlfriend whom I also bought a Tilt for, her's doesn't do it.
We've installed all the same software too, so I'm a little puzzled.
start>settings>system> key lock. set it to lock all buttons except power.
rzanology said:
start>settings>system> key lock. set it to lock all buttons except power.
Click to expand...
Click to collapse
Hmmm.. yeah, umm my key lock is already set to lock all buttons except power.
The problem isn't with when you press a button it comes on. The problem is the phone turns on by itself, sitting on a table, nothing being pressed, no new email, no new sms, just lights up and that's it.
JonRick said:
Hmmm.. yeah, umm my key lock is already set to lock all buttons except power.
The problem isn't with when you press a button it comes on. The problem is the phone turns on by itself, sitting on a table, nothing being pressed, no new email, no new sms, just lights up and that's it.
Click to expand...
Click to collapse
Any number of applications might be starting the device, from weather apps to calendar, diary, time sync etc etc. For example, HTCs weather app will do it depending on how often you have it set to another example I came across from someone was TREO ALERTS that contains a script "refresh.mscr" and it was set up refresh time 30 seconds (this was turning his TyTn II on by itself).
Mike
hard reset and try again.
i'm betting that none of these suggestions were helpful (except the one about some application generating a wakeup event without any other visual notifications).
i was having the same problem, but i just tried to narrow down which running program was causing the events. it's one of:
* wireless manager
* messaging
* IM
my guess is IM; i'm going to test that out in a second.
well, it's none of the above. still seems to wake up randomly anywhere from 15 seconds to several minutes.
seems to happen more frequently when it's just been turned off.
Even if you were to find what was turing the phone back on, this can still be a problem just from normal use... obviously, you WANT the phone to turn on for things like a call coming in. The solution for people like us who stick our phones in our pockets is to "lock" the phone. But for whatever reason, the Tilt doesn't lock the phone while holding down the end key. That means the only convenient way to lock it is to keep the lock function on the today screen, wasting space. Hopefully someone can find a way to allow the end key to lock the device on the Tilt just like the unbranded device.
dscline said:
Even if you were to find what was turing the phone back on, this can still be a problem just from normal use... obviously, you WANT the phone to turn on for things like a call coming in. The solution for people like us who stick our phones in our pockets is to "lock" the phone. But for whatever reason, the Tilt doesn't lock the phone while holding down the end key. That means the only convenient way to lock it is to keep the lock function on the today screen, wasting space. Hopefully someone can find a way to allow the end key to lock the device on the Tilt just like the unbranded device.
Click to expand...
Click to collapse
i'm fine with using the lock function, but it still turns on randomly, using battery, and eventually unnecessarily yellowing the screen from backlight aging. my next approach is to check out the notification queue, using a notification cleaner app.
So i am having a similar problem. When i press the power button, the phone's screen turns off but when the keyboard slides, it turns back on... is there a way to make it so the keyboard sliding does not turn on the device? I think the keyboard slides around a little when in my pocket and i hate pushing 3 buttons to unlock my phone... thanks
I was having the same problem.
This is an issue with the ATT rom. Flash over HTC rom and you will be all set.
I have been having the same problem as well. I just installed this DeviceLock program:
http://forum.xda-developers.com/showthread.php?t=305402
If you enable the "Lock on Wake" option, the device will be locked when it wakes up, so the backlight stays off and you won't call anyone by accidentally hitting buttons.
Also, I ran across this related thread you might want to check out (basically talking about the same thing, but for the TyTn II):
http://forum.xda-developers.com/showthread.php?t=341419
Related
Hi, I have discovered that Direct Push e-mail is causing the wizard to power on at certain intervals and for me at least was causing significant power drains under crossbow. Here are 2 fixes.
1. This is for those that use an exchange server and/or direct push email.
-Locking the device stops the wizard powering on and still allows use of direct push email.
2. Those that don't wish to lock their device and don't use direct push email.
-Change the following Registry values:
HKEY_CURRENT_USER\Software\Microsoft\ActiveSync\
HeartbeatIncrement DWORD: 0
InitialHeartbeat DWORD: 0
MinHeartbeat DWORD: 0
MaxHeartbeat DWORD: 0
Reset
Hopefully this will work for you guys it did for me, no power on all night.
EDIT: Sorry after longer testing No. 2 appears not to work however I still think it has something to do with Activesync and Direct Push E-mail. The settings reset themselves after soft reset.
It works!
Confirmed. Locking the device via the Today screen plug-in prevents the undesired power ups.
I am using a small program called Device Lock with the Suspend option. I set Button 4(Hold) to Device Lock. Sometimes it wakes up immediately after suspending, but I can press the power button and it stays off.
http://forum.xda-developers.com/showthread.php?t=261277
I discovered this yesterday also.
He means using the today screen plugin to lock it, not just having buttons locked except power in case you weren't aware of that.
No wonder I never had this problem. I use batterystatus to lock my screen all the time. Isn't the lock nice? Very convinent. My only hope is if there is anyway to unlock it with one hard button.
Oh. I was using the Lock in the control panel set to lock after 0 minutes of idle so when I pressed power it would power down and lock.
I'll have to find a better way to lock.
it didnt work....
Malik05 said:
it didnt work....
Click to expand...
Click to collapse
using the batterystatus, not the lock in the control panel.
i meant the regedits, it didnt fix the problem...i dont like to lock my phone when not in my pocket...
i hit the lock button on the today screen and i watch it turn on and off every minute... still... it didn't help ...
I wonder how did faria fix it in his ROM.
any update? wokring solution ?
Faria has the only known solution to this but is refusing to share that knowledge by looks of things, maybe so he can forces users to use his own cooked ROM or something...
the only working solution i have seen was the one rusigor suggested and that was taking the device password off. and im believer because it worked for me. so im sticking with that. Also i noticed that my battery is lasting like alot lot lot lot lot lot lot longer now. before i would go to bed with the phone at 80% battery and when i would wake up it would be like at 30. The last couple nights i would go to bed with it at 59 and woke up and it was at 55. I was shocked. so thats why im sticking with this method.
neonkoala said:
Faria has the only known solution to this but is refusing to share that knowledge by looks of things, maybe so he can forces users to use his own cooked ROM or something...
Click to expand...
Click to collapse
I hope it's just a case of him not knowing of this thread! Has anyone PM'd him?
I will if no one has yet.
Karl
Sorry meant to update this, fix has been around for a little while now.
Untick Turn off backlight for both battery and mains power and this will cure the problem however you may still have automatic power offs.
I don't use push, nor do I have an Exchange server configured. I also had a problem with automatic power-ups. I found that having the device configured to display the owner info screen when it is switched on caused it to power up on its own shortly after it was switched off.
Getting rid of the owner info display on power-up did the trick for me.
I'd love to know how those two things are connected.
I found a solution for me
I also think is more related with the screen light as I used the WM6 MB and i put the screen auto off after 30 sec, and it was waking up very frequently. I completly removed the screen light auto off and now my phone never wakes up alone (just when it should be =D).
Hope it helps!
Hello everyone. I have an AT&T Tilt, and it's great so far, except for two issues:
1) After I end a phone call, the backlight seems to go off and the screen is very dim. Pressing keys does not bring the backlight back. If I power the screen off and on, the backlight comes back on and the screen is at its normal brightness.
2) I lock my AT&T Tilt using the "Device unlocked" area on my home screen, and when I unlock the phone, sometimes it asks for my PIN, and sometimes it just shows the unlock button on the screen. My settings are for a 12 hour timeout.
If anyone can shed any light on possible fixes to these issues, that would be great. Thanks!
mrbofus said:
Hello everyone. I have an AT&T Tilt, and it's great so far, except for two issues:
1) After I end a phone call, the backlight seems to go off and the screen is very dim. Pressing keys does not bring the backlight back. If I power the screen off and on, the backlight comes back on and the screen is at its normal brightness.
2) I lock my AT&T Tilt using the "Device unlocked" area on my home screen, and when I unlock the phone, sometimes it asks for my PIN, and sometimes it just shows the unlock button on the screen. My settings are for a 12 hour timeout.
If anyone can shed any light on possible fixes to these issues, that would be great. Thanks!
Click to expand...
Click to collapse
I have the same issue after a phone call....
Same issue here too... it doesn't happen when on USB-power... and I don't remember it doing this before the security-Exchange policy was forced onto my phone.
http://forum.xda-developers.com/showpost.php?p=1566518&postcount=2
I think this happens coz the phone goes into standby / lock mode during your phone call. Just press the on/off button to turn screen off, and press again to turn on. Now your phone will be responsive again.
Minor bug.
Or you can just scroll the volume wheel to turn it back on.
michi123 said:
http://forum.xda-developers.com/showpost.php?p=1566518&postcount=2
Click to expand...
Click to collapse
thanks michi
thanks everyone for your replies. I will try the StayUnlock application.
I still don't understand my second issue though. If the bug is causing this issue, shouldn't it at least be consistent in either requiring me to type in my PIN or just hit the unlock button? I have set my phone to lock after 12 hours, so it should never ask for my PIN, just the unlock button...
I now see that people have been having the first issue since the Cingular 8125 but I have been unable to find any references to my second issue.
ATT Til and Backlight
When making a phone call, once connected, about 12 seconds later the screen goes dark regardless of the setting on the backlight. I am not using a password, and the only way to get back is to use the power button. using the phone button puts the call on hold
Well I've had my Tilt for a week now and I have been frustrated completely with the Phone App.
First of all, when I am calling a tone prompted location where you have to press the keys to get somewhere (611, corporate voicemail, etc), some of the time the phone will go into "hold" when i press the keys.
Secondly, after a call that i have pressed the keys for tone operation, the phone app will not completely close. the screen will stay half dim and the start bar and task panes are locked out. i can't access any of the icons at the top of the screen. the only button available is the task manager which shows no programs running.
i can pretty much replicate the 2nd problem consistently. does anyone else have this problem? Please try to call into a company say even 611, go through all the tone prompts and see if the phone app closes appropriately afterwards. make sure you are on the phone long enough for the screen to automatically dim.
the only way for me to get past this is to softboot so i can get access to the start menu again. but i'd rather not have to softboot after every phone call =T
Thanks!
Same problem here, any help would be great.
Massiv
disable the lock thing where you have to enter a pin - i think its a bug in the rom
Same problem - but if press the on/off button for the screen twice I do have again access to all icons. Not nice but ....
yeah i was messing around with the phone last night and realized that it has to do with phone lock and figured out if you press the power button to put it to sleep and press it again to wake it up, everything is normal again. it was just a fluke how i found out but i'm glad to know that this isn't only my problem. i was about to do another hard reset on the phone.
i called ATT techsupport and they told me it might be the simcard. can other Tilt owners chime in here. is this a ROM problem or could it be related to a faulty sim?
http://forum.xda-developers.com/showpost.php?p=1566518&postcount=2
Hey guys,
Right, I've come over from symbian, namely UIQ and the SE P-series, so am used to things being somewhat different. The main issue I don't seem to be able to find a solution to is the screen locking problem.
Essentially, at the moment I push the power button to lock the device, as well as enter a power save mode. I have to say, I like the way that works. However, when I recieve a call (or text with the reg fix) the phone comes to life, great, but say I miss the call, or the phone is in my pocket, the screen is now ACTIVE. Not good news.
How am I supposed to lock this device properly? Screen lock and then the power button? Can't I get a simple tap on the power button to lock and power save the device?
Essentially, if I have a missed call or message I just want the phone to vibrate once, then keep an LED flashing intermittently. But I want the screen to stay LOCKED.
Any help would be much appreciated, and thanks for all the other useful tips on the forum!
Cheers,
Daz.
Go start/settings/System/Long Press End Key
Select automatically execute etc
and Lock device
then OK
then, a long press on the hang up button (bottom right) will lock the phone.
Hope that helps
Perhaps I didn't explain myself. I know how to lock the phone, but how do I make use of the power button tap mode? In other words, the power saving mode?
Can I set up a button that locks the phone, AND sends it to power save mode? (or "turn it off" as WM seems to call it).
Thanks again,
Daz.
I found a regedit in:
HKLM\Software\HTC\KeyLock\SameAsDeviceLock
Set it to 1, but it doesn't do the trick. In fact, it now causes the power button click to not lock the keys.
I suppose the only option is to have standby mode come on after a timeout, lock the device, then it will go into standby on its own. Seems like a slight waste of battery to me!
Cheers,
Daz.
I really want this to work too,
It should unlock and turn on when recieving a call, it should just turn on when recieving an sms (so you can have a quick look from who it is, and then unlock to reply)
and when you lock the device it should automatically turn off...
Not EXACTLY what you want, but S2U2 in the "Development and Hacking" section will improve matters for you.
When you turn the phone off with the power button, S2U2 kicks in. Then:
1) If you turn the phone back on, you'll get the slide to unlock screen.
2) If a call comes in, the phone turns on and you see the caller ID (with full screen picture, if you so desire) on a "slide to answer" screen. The S2U2 default settings ensure that the phone turns itself back off again if you fail to answer it.
3) If a text / e-mail / mms comes through, it notifies you but remains off... When you hit the power button, the "slide to unlock" screen will show missed calls, text messages, e-mails (and even the weather if you want...).
Check it out, it's an essential piece of software in my opinion... http://forum.xda-developers.com/showthread.php?t=381588
Thanks sub69, great recommendation. However, does anyone else get the bug when hitting the "x" in other applications to close them, the status bar (Or task bar) goes all scrambled and looks like the S2U2 status bar.
Shame this isn't built in though, would be nicer to see the TF3D interface rather than a 3rd party one.
Thanks again!
Daz.
Anyone with other suggestions? S2U2 is just a little too buggy at the moment on the diamond...
use "BatteryStatus" from www.chti-tai.info, they have a option for devicelock on wakeup, so even u missed a call, and the screen light up, it is still locked.
somone posted this on other thread.
--------------------------------------------------------------------------------
Now we don't need any devicelock software with diamond.
If you want automatic lock your diamond you have to change this registry key HKEY_CURRENT_USER\ControlPanel\BackLight\AutoDevic eLockEnable from 0 to 1 and everytime your backlight goes off automatically your device are locked
Sorry for may bad english but i'm italian.
Ciao
Thanks for that reg fix, seems like a good option. There was a new S2U2 version release, 1.5, and that seems to work well for me. Will see how that goes for now...
Cheers guys! Daz.
the reg edit is good, but it doesn't solve the problem of unlocked touchscreen prone to being pressed during incoming call (when scrambling in your pocket to take out the phone)
btw there are several other threads where this problem is addressed and deeply analyzed (without a complete working solution, however...)
dazbradbury take a look at sensorlock, if you have not already.
Basically I had a look about here and can't see anyone else with the same issue.
I've not long had the phone and the other night I had a call quite late saying I'd been phoning them 5 times. I'd locked my phone but when I looked at it it was awake and unlocked.
I can lock my phone (hold down the end call key) but with a bit of movement to the phone it brings up the unlock screen and unlocks itself.
This also happens if I lock the phone and turn off the screen with the power button. After a little shake about the phone will turn on and unlock itself.
You can imagine the problems this can cause whilst in my pocket.
I've not messed with the firmware yet or even any registry entries, it's as it was from HTC.
I am having this same issue with mine. I hold down the End key for a few seconds to lock, it locks successfully, but if I move my finger a bit and touch any other part of the surface it unlocks almost instantly. Sometimes the lock remains, but it's more likely that it will get unlocked.
I tried using TouchLockPro, but that didn't seem to help me much (it seems like it's not even functioning, actually). I'm running A.Z.T.O.R. V7 WWE ROM.
Nick
Have you tried going to settings then hitting "key lock". On the screen that comes up check the first option "lock all buttons except power button".
Works fine for me - when I switch off screen using power button everything is locked (buttons and screen) until I hit power button again or I get an incoming call.
Mine is set to that, but it doesn't seem to have much effect.
Sometimes I will hit the power button to shut the screen off and later when I pull it out of my pocket the screen is on and something (e.g. Calendar, System Time, etc) is open. During the period it was in my pocket I received no calls or texts.
When I try to hold the end key to lock the phone, it will lock it for ~1 second and then automatically unlock it. Doing it a second or third time will usually get a lock that "sticks" (at least for a while).
There has to be a good solution for this out there, but I've tried PocketShield and TouchLockPro without luck.
Nick
Diamond unlocks itself
I have this problem as well. I went to a meeting, locked my phone and it made 20 calls to my friend abroad, so I am really pissed, it happened before but I thought it was because it got knocked in my handbag.- Please help
Also my battery life has depreciated in a big way, at first 24 hours , 4 months later I'm lucky if it's lasting 6 hours and that's without making a call. I've turned of wi-fi, 3G etc. What is happening
Use sensorlock its great if you set it to unlock when you take the stylus out and relock when u slide it back in
mancsoulja said:
Use sensorlock its great if you set it to unlock when you take the stylus out and relock when u slide it back in
Click to expand...
Click to collapse
TouchLockPro should just work. In post #5 alternatives are mentioned (and also why the built-in Windows Mobile lock is not a solution for your problem)!