usb not reconizer HELP - Tilt, TyTN II, MDA Vario III General

my computer is not reconizer this my Kaiser help me urgent

That's very little information. Has it ever worked? What have you changed recently? Does your computer even acknowledge that the device was plugged in? Is there an existing partnership?
You can try ending all partnerships between the computer and the phone. Without knowing what you've done, it's hard to give any more advice than that.
I'd also direct you to the Wiki and the Sticky...they both have lots and lots of information about the phone. I'm just assuming this has something to do with flashing a ROM on your phone because it's in the Upgrading forum and not the general Kaiser forum.

dont understand, i have windows xp and activesync dont have reconizer the kaiser!!! and dont flash the pda :S:S

Your English is obviously poor.
So, try this:
1) delete your devise from Activesync.
2) reboot your computer
3) plug in your phone to the computer.

Make sure you have the latest version of ActiveSync as well.
If I understand you correctly, you have not flashed your phone. Is that correct? If I am correct and you are still using the original ROM and software, then this question really belongs in the Kaiser forum and not the Kaiser Upgrading forum.

grizzley said:
Your English is obviously poor.
So, try this:
1) delete your devise from Activesync.
2) reboot your computer
3) plug in your phone to the computer.
Click to expand...
Click to collapse
DOnt Work!!!!!! :S flash without usb ???? how to???

x-club said:
DOnt Work!!!!!! :S flash without usb ???? how to???
Click to expand...
Click to collapse
HELLO I HAVE THE SAME TROUBLE WITH MY TILT THE USB IS NOT WORKING SO I HAD TO USE MY SD CARD AND FLASH MY PHONE ITS KIND HARD BUT ONE YOU READ AND DO STEP BY STEP IT REALLY EASY.IM SENDING YOU THI SITE TO READ ON HOW TO DO THIS HOPE THIS HELPS AND IF SO PLEASE LEAVE A COMMENT ON HOW I HELPED I PROMISED THIS SITE SINCE THERE ARE FEW THAT TAKE THE TIME TO QWORK WITH YOU FOR FREE I SAID I WOULD TRY TO DO THE SAME.. A SPECIAL THANKS TO ALLTHE WAY FOR TEACHING ME.....
http://forum.xda-developers.com/showthread.php?t=336158
Flashing using MicroSD Card - xda-developers HOPE THIS IS WHAT YOUR LOOKING FOR..GODBLESS....

sexylatin1 said:
HELLO I HAVE THE SAME TROUBLE WITH MY TILT THE USB IS NOT WORKING SO I HAD TO USE MY SD CARD AND FLASH MY PHONE ITS KIND HARD BUT ONE YOU READ AND DO STEP BY STEP IT REALLY EASY.IM SENDING YOU THI SITE TO READ ON HOW TO DO THIS HOPE THIS HELPS AND IF SO PLEASE LEAVE A COMMENT ON HOW I HELPED I PROMISED THIS SITE SINCE THERE ARE FEW THAT TAKE THE TIME TO QWORK WITH YOU FOR FREE I SAID I WOULD TRY TO DO THE SAME.. A SPECIAL THANKS TO ALLTHE WAY FOR TEACHING ME.....
http://forum.xda-developers.com/showthread.php?t=336158
Flashing using MicroSD Card - xda-developers HOPE THIS IS WHAT YOUR LOOKING FOR..GODBLESS....
Click to expand...
Click to collapse
how to format microsd and is work in card 2GB?

x-club said:
DOnt Work!!!!!! :S flash without usb ???? how to???
Click to expand...
Click to collapse
If this is the best you can come up with after people have tried to help then I guess you haven't read the WIKI yet.
It's obvious English isn't your first language, but if you don't read AND understand the WIKI then you will break your phone.
If necessary get a friend to help with translation. Or post your question in English and your own language - then maybe someone on the forum who speaks your language can help out.

Related

How to put Herald in boot loader mode ?

Hello,
I've searched a lot how to put the Herald in the boot loader mode.
Please, help me.
Thank you advance.
LAter edit: i found out: i had to keep pressed the camera button lol
If you searched a lil bit more you'll find that piece of info in herehttp://wiki.xda-developers.com/index.php?pagename=Herald_Resets
in the Wiki herald section
sandibad said:
Hello,
I've searched a lot how to put the Herald in the boot loader mode.
Please, help me.
Thank you advance.
LAter edit: i found out: i had to keep pressed the camera button lol
Click to expand...
Click to collapse
and in nearly everypost about unbricking and flashing.
Pleas read, read, read.
and btw: commmanager + camera + softreset.
Looking for
In fact, i read houdreds of time all the posts... at 5 AM...
Because by Herald was in the "white screen" and i was desperate...loking for solution ...
In fact, I have to wait for the official WM6 because that one didn't worked for me.
Thks for assistance.
papamopps said:
and in nearly everypost about unbricking and flashing.
Pleas read, read, read.
and btw: commmanager + camera + softreset.
Click to expand...
Click to collapse
No need to press comm.button. Just press camera and softreset at once, release the softreset first than camera button. That's all!
nugift said:
No need to press comm.button. Just press camera and softreset at once, release the softreset first than camera button. That's all!
Click to expand...
Click to collapse
OK. Thanks
BTW - my device is unbricked. BUT it was made by repairservice - for warenty. lol.
I´m happy again. Hehe
papamopps said:
OK. Thanks
BTW - my device is unbricked. BUT it was made by repairservice - for warenty. lol.
I´m happy again. Hehe
Click to expand...
Click to collapse
Damn you did not have to pay?? sweet!
Newbie here.....
I have an HTC P4350. During the upgrade, there was a disconnect with my computer to the phone, now I have that colored screen when I start up. I tried the hard and soft reset and also the Boot loader method.
Anyone have any other suggestions?
Do you think if the phone went back to HTC, they would be able to fix it?
Thanks for your help
You should be able to flash the original RUU when you're in bootloader mode ('the three colored screen') and connected to the PC with your USB cable. Worked for me anyways.
Just put your phone in bootloader mode, connect it to your computer and run the RUU.
R_phAn said:
You should be able to flash the original RUU when you're in bootloader mode ('the three colored screen') and connected to the PC with your USB cable. Worked for me anyways.
Just put your phone in bootloader mode, connect it to your computer and run the RUU.
Click to expand...
Click to collapse
The problem is that it won't connect to the computer via activeSync, until that happens the phone cannot be updated.
passmoregas23 said:
The problem is that it won't connect to the computer via activeSync, until that happens the phone cannot be updated.
Click to expand...
Click to collapse
Have you tried it before you said that it would not work? Seriously? When in bootloader mode, the computer doesn't connect via activesync (how could it, there is no operating system on the phone). Get into bootloader mode, connect the phone to the computer (yes, i know activesync doesn't show a connection at this point) and run the stock RUU for your device. If this does not work, then there is something seriously wrong with your device.
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
dcmtnbkr said:
Have you tried it before you said that it would not work? Seriously? When in bootloader mode, the computer doesn't connect via activesync (how could it, there is no operating system on the phone). Get into bootloader mode, connect the phone to the computer (yes, i know activesync doesn't show a connection at this point) and run the stock RUU for your device. If this does not work, then there is something seriously wrong with your device.
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
Click to expand...
Click to collapse
To add to this, when in bootloader and plugged into your PC, it will say "USB" at the bottom. That's how you know it's connected properly.
If you're having troubles and you're running Vista...
http://www.modaco.com/RUU-Vista-done-u-t252977.html
dcmtnbkr said:
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
Click to expand...
Click to collapse
Dude, I have searched for a resolve to my problem, and I do appreciate peoples help. I don't waste time of good Samaritans. I did run the RRU and I received an 260 error, which is another topic which I did research on as well.
I'm going to send the phone back to HTC and let them fix it.

Need help Htc Tytn II

I have a queston
I have a vodafone v1615
To unlock my TYTN II i have to use the kaiser sim unlocker v0.1
In the instrutions i read that i have to instal the hardSPL- 1.0 OLipof then this will workt what to do fist run the kaiser-HardSPLv1 then install a new rom and then run the sim unlocker
can anyone help me please i have been reading so much stuff in dont understand it anymore what do i have to do first and what programs do i have to use
HardSPLv1
Duttys_Official_WM6[1].1_Release
kaiser-simunlocker
This is what i downloaded on my pc
bajai said:
I have a queston
I have a vodafone v1615
To unlock my TYTN II i have to use the kaiser sim unlocker v0.1
In the instrutions i read that i have to instal the hardSPL- 1.0 OLipof then this will workt what to do fist run the kaiser-HardSPLv1 then install a new rom and then run the sim unlocker
can anyone help me please i have been reading so much stuff in dont understand it anymore what do i have to do first and what programs do i have to use
HardSPLv1
Duttys_Official_WM6[1].1_Release
kaiser-simunlocker
This is what i downloaded on my pc
Click to expand...
Click to collapse
I personally would have ask this question in one of the three threads you read about this process in.
Let me reinterate the most important point that seems to be overlooked a lot. No offense meant to the OP.
YOU MUST HAVE HARDSPL INSTALLED FIRST TO DO ANY FLASHING OR UNLOCKING!
I would personally say Do It in that order. HardSPL, ROM, Then SIMUnlock.
JimmyMcGee said:
I personally would have ask this question in one of the three threads you read about this process in.
Let me reinterate the most important point that seems to be overlooked a lot. No offense meant to the OP.
YOU MUST HAVE HARDSPL INSTALLED FIRST TO DO ANY FLASHING OR UNLOCKING!
I would personally say Do It in that order. HardSPL, ROM, Then SIMUnlock.
Click to expand...
Click to collapse
I have windows vista on my pc is that oke for al these programs or do i have to do this all in windows xp
bajai said:
Thanx for that hope that all this will work i'm a little affraid that my phone becomes a very expensive brick
Click to expand...
Click to collapse
That is part of the fun. Also, Just don't pull out your USB cable. Unless everything is complete. Unless instructed otherwise
JimmyMcGee said:
That is part of the fun. Also, Just don't pull out your USB cable. Unless everything is complete. Unless instructed otherwise
Click to expand...
Click to collapse
hahaha thanx i will read the instructions if not then it will become a brick for my house, thanx man hopefull its runs on vista as well i heard and have been reading xp its better to do all of this what do you think about this
bajai said:
hahaha thanx i will read the instructions if not then it will become a brick for my house, thanx man hopefull its runs on vista as well i heard and have been reading xp its better to do all of this what do you think about this
Click to expand...
Click to collapse
I've only ever done it on XP. Though Vista is picky about some things so make sure you are logged in as Administrator. I've heard others have had luck.
JimmyMcGee said:
I've only ever done it on XP. Though Vista is picky about some things so make sure you are logged in as Administrator. I've heard others have had luck.
Click to expand...
Click to collapse
oke i will use xp for this all thanx
what is Kaiser SuperCID and Security Unlocker + HardSPL what does this mean??????

HTC TYTN II - How to recover from bad flash.

Greetings everyone,
I would like to ask for some advice.
I bought a HTC TYTN II and wanted to flash it to a ROM I found on the forum.
But to do that I had to use nueSPL-2.47.exe
That turned out to be a mistake as at the moment it started formatting to FAT32 the screen freezed. And I waited for around 15min. But nothing happend.
Now needless to say the device does not function. I tried a hard reset(Camera+Power+Reset) and just (Reset). But all I get is a screen darker than the pits off hell.
I am able to get the power light burning but that is it. Already tried putting the battery out and in again. But all to no avail. Maybe one of you can help me?
Thank you in advance.
-
Previous OS: Windows 6.1 (Dutch)
Active sync: 4.5.0
PC OS: Windows XP pro (English)
Just a thought but...you might want to check the Kaiser forum instead...
Posted in Titan forum. Moved to Kaiser forum.
You flashed a Titan SPL to your Kaiser?
Oh dear, not to worry, it might be fixable...
Can you get to your Bootloader?
Ta
Dave
Confused "Tytn" with "Titan", too bad.. That's already happened, if you search for "nuespl" in the Kaiser forum you should find a thread about someone else who had the same problem recently.
kilrah said:
Confused "Tytn" with "Titan", too bad.. That's already happened, if you search for "nuespl" in the Kaiser forum you should find a thread about someone else who had the same problem recently.
Click to expand...
Click to collapse
The other guy never fixed his phone
Dave
uh oh... what was your radio version? does the PC still try to load a driver when you connect the phone?
Wrong firmware now that explains things.
It seems that the soft/hard reset and boot loader are not working for me. All I ever get is the power light and no screen at all.
Just my luck.
My phone was a 3G version.
When I connect it via USB it does try and load drivers but it does not find the correct drivers. While the phone was ok the drivers were fine.
Strange.
I sure hope I do not have to send it to my supplier. Because the phone is just 2 weeks old ;-)
Jin_member_of_triforce said:
Wrong firmware now that explains things.
It seems that the soft/hard reset and boot loader are not working for me. All I ever get is the power light and no screen at all.
Just my luck.
My phone was a 3G version.
When I connect it via USB it does try and load drivers but it does not find the correct drivers. While the phone was ok the drivers were fine.
Strange.
Click to expand...
Click to collapse
are you able to load these drivers: http://forum.xda-developers.com/attachment.php?attachmentid=71038&d=1203255530
3G, okay, all of them are 3G... do you remember exact radio version. no problem if not, though.
Sorry I do not know the exact number.
I was able to install the drivers. So thanks for that.
But If I try and get onto my phone I have no folders. And active sync does not see the device. Maybe I need to use a program like artemis to get files on there?
There is of course a change I might be able to get files on there by putting my SD card in a card reader.
But does it boot from there?
Pocket controller-pro did not work for me.
Jin_member_of_triforce said:
Sorry I do not know the exact number.
I was able to install the drivers. So thanks for that.
But If I try and get onto my phone I have no folders. And active sync does not see the device. Maybe I need to use a program like artemis to get files on there?
Click to expand...
Click to collapse
that will not help, but there is another way... PM me, as it needs interactive step by step instructions.
im having the same issue i just ran the neuspl 2.47 and my htc tilt wont work the power light comes on and thats it can somepone please help me out i am in need of help badly!

totally confused....about JUMP-SPL and HARD-SPL

I have watch videos...read instruction etc, etc, all I could on ATT Tilt/Kaiser flashing...I still don't have a clue. Do I do some type of CID unlock 1st....then is there a Jump SPL and than a Hard SPL. Is any of them two done from the boot loader screen. I can fix most electronics but I don't understand.. no you-tube video...i saw it on flashing the kaiser....sound quality bad for the hard of hearing (me).
Goto http://forum.xda-developers.com/showthread.php?t=396922
Download Jump SPL and Run it. Then the hard-spl. This will then allow you to flash the custom ROMs on your Kaiser.
Regards,
Carty..
I just went through this a few days ago trying to flash my first custom rom. I have to agree it is incredibly confusing and contradicting, which is why I'm taking the time to post this. Just read as much as you can about it and don't try to flash the rom until you understand. I am no expert on this by any means, but this is what i did on my tilt to flash HardSPL. I tried to make this as simple as possible just so you see the exact steps I went through, but i highly recommend reading the thread linked in the previous post by Carty above and the other link I'm posting at the very end.
1. download JumpSPL1.93-KAIS.exe from http://forum.xda-developers.com/showthread.php?t=354061.
2. get the hardSPL version you need for your rom. I used v3.56 from the link Carty gave you in the post above, because the rom I am using was based on the official att 6.1 rom. You may need a different one for the rom you want to flash I don't know too much about this yet. Leave the folder where you unzipped the hardspl files open on your desktop so you wont have to look for it later.
3. connect your phone to the PC, and transfer JumpSPL1.93-KAIS.exe over to your phone with activesync. Remove your microsd card if you have one on your phone (very important).
4.run JumpSPL1.93-KAIS.exe on your phone, it should go to a bootloader mode with the tricolor screen and underneath it will say USB.
5.Unplug the phone from the PC, wait about 5-10 seconds and plug it back in. Activesync should NOT be able to recognize your phone. If it does, something went wrong so start over.
6. Finally you can run the KaiserCustomRUU.exe from the hardSPL folder on your pc desktop and follow the instructions. It will load the HardSPL on your phone.
7. if you want to make sure it loaded, shut down your device and when your are turning it on press both the power and camera button at the same time, it will go into bootloader mode and show you what SPL is on your device. mine says SPL-3.56.Hard after I loaded the hardspl. You are now ready to flash a new rom.
This wiki helped me the most:
http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
Read as much of it as you can, especially the "SPL questions?" link, that was the most useful for me.
I hope this helps
All good advice! I just loaded the HardSPL on my phone for the first time and it worked perfectly.
Now all i need is a work connection that doesnt block my attempts to download ROM's!!!!!!
tricky_uk said:
All good advice! I just loaded the HardSPL on my phone for the first time and it worked perfectly.
Now all i need is a work connection that doesnt block my attempts to download ROM's!!!!!!
Click to expand...
Click to collapse
LOL.
hjlow makes mirrors of the ROM downloads at Blogspot. Are those any good for you?
Ta
Dave
DaveShaw said:
LOL.
hjlow makes mirrors of the ROM downloads at Blogspot. Are those any good for you?
Ta
Dave
Click to expand...
Click to collapse
Sadly blogspot gets locked as well.......i've managed to download some stuff of here but in general sites it classes as 'personal storage' it gets a bit upset about...
if anyone knows any other way round i'd be eternally grateful!
ben_zin said:
I just went through this a few days ago trying to flash my first custom rom. I have to agree it is incredibly confusing and contradicting, which is why I'm taking the time to post this. Just read as much as you can about it and don't try to flash the rom until you understand. I am no expert on this by any means, but this is what i did on my tilt to flash HardSPL. I tried to make this as simple as possible just so you see the exact steps I went through, but i highly recommend reading the thread linked in the previous post by Carty above and the other link I'm posting at the very end.
Click to expand...
Click to collapse
Amen to that.. I like this guy.
Thx...clear and direct....now I am ready.
Carty said:
Goto http://forum.xda-developers.com/showthread.php?t=396922
Download Jump SPL and Run it. Then the hard-spl. This will then allow you to flash the custom ROMs on your Kaiser.
Regards,
Carty..
Click to expand...
Click to collapse
does this work on diamond?or i mean, should i frist jump spl ant hen hard, or just jump spl?
http://forum.xda-developers.com/showthread.php?t=408109&page=506 post 5055
materijalmen said:
does this work on diamond?or i mean, should i frist jump spl ant hen hard, or just jump spl?
http://forum.xda-developers.com/showthread.php?t=408109&page=506 post 5055
Click to expand...
Click to collapse
This will then allow you to flash the custom ROMs on your Kaiser.
Click to expand...
Click to collapse
No , this is what works on the Diamond
http://forum.xda-developers.com/showthread.php?t=414835
denco7 said:
No , this is what works on the Diamond
http://forum.xda-developers.com/showthread.php?t=414835
Click to expand...
Click to collapse
i have tried this already
http://forum.xda-developers.com/showthread.php?t=408621 but nothing has changed...i asked for help, but nobody answers....see the last posts int that thread.
materijalmen said:
i have tried this already
http://forum.xda-developers.com/showthread.php?t=408621 but nothing has changed...i asked for help, but nobody answers....see the last posts int that thread.
Click to expand...
Click to collapse
Unfortunately this is the Kaiser forum and you will get even less help here.
Post your questions in the Diamond forum and people will help,when and if they are able. And in the meantime, read and search and try to figure it out for yourself, All the steps and instructions are there.
Sometimes people, unfortunately, mistake this site for the HTC free support line, with 12 techs waiting at their PC's to help. Then they get irritated that no one answers their requests for help on a timely basis . If people won't or can't answer your questions then you need to figure it out on your own.
The bottom line is, if you don't know what you are doing, then you shouldn't be messing around with your phone. Sorry
denco7 said:
Unfortunately this is the Kaiser forum and you will get even less help here.
Post your questions in the Diamond forum and people will help,when and if they are able. And in the meantime, read and search and try to figure it out for yourself, All the steps and instructions are there.
Sometimes people, unfortunately, mistake this site for the HTC free support line, with 12 techs waiting at their PC's to help. Then they get irritated that no one answers their requests for help on a timely basis . If people won't or can't answer your questions then you need to figure it out on your own.
The bottom line is, if you don't know what you are doing, then you shouldn't be messing around with your phone. Sorry
Click to expand...
Click to collapse
I second Denco Read Read Read Read Read........ as anything you will ask, or can even think to ask..... more than likely has ALREADY been asked AND Answered.
Htc XDA member: how can I help you today?
Xda Newb: My phone isnt working.... Can you fix it ?
Htc XDA member: is your phone plugged in and turned on?"
Xda Newb:Wheres the on button?
( 1 min later) where do I plug it in at ?
(2 mins later) whats a battery?
(2.25 mins later) how do I know its on?
(2.3 mins later) why wont you answer me ?
(2.35mins later)Why arent you telling me my answers?
(2.4 mins later)whats wrong with my phone?
(2.5 mins later) You guys must be jerks because you wont spoon feed me [email protected]@@!!!
XDA MODERATOR : you noob you are banned for not reading PAGE 1 of the GODDAMN WIKI as all your answers were right there 1 click away. Now you cant access them HAHA. This is what you get for being IMPATIENT AND ANNOYING ( They should really do this here )
LOL
Just my rant
denco7 said:
No , this is what works on the Diamond
http://forum.xda-developers.com/showthread.php?t=414835
Click to expand...
Click to collapse
How is this link related to the topic?
I want to use JumpSPL to change the version of HardSPL I have on diamond b/c my USB port does not work.
kyniemxotxa98 said:
How is this link related to the topic?
I want to use JumpSPL to change the version of HardSPL I have on diamond b/c my USB port does not work.
Click to expand...
Click to collapse
And what I said was that this was the Kaiser forums and not the Diamond forums. Putting Kaiser Spl's on a Diamond will brick your phone faster than throwing it into a bucket of water. So I gave him a link to the Diamond forum and Diamond Security/CID/Sim unlocker.
How is your question related to the Kaiser forums ?
Will it work on my TP/Excalibur? No as phones have different hardware to which is why h-spl's are device specific.
The best way to help yourself and not get a brick "expensive paperweight" is to head to device subforum and do some reading, as last thing you want is to be creating a thread named "Help"
denco7 said:
And what I said was that this was the Kaiser forums and not the Diamond forums. Putting Kaiser Spl's on a Diamond will brick your phone faster than throwing it into a bucket of water. So I gave him a link to the Diamond forum and Diamond Security/CID/Sim unlocker.
How is your question related to the Kaiser forums ?
Click to expand...
Click to collapse
Since I cannot find anything helpful in Diamond forum, I dig around in other forums to try to rescue my phone and make it usable.
Which is a recipe for diasaster...seriously, if you are gonna do something as stupid as to try to make something SPECIFICALLY for another device work on yours, then you do not deserve to own a Diamond.

Xperia brainfart: Problems with flashing

So people around here sometimes get troubled with regular flashing that doesn't work anymore.
I'll explain my problem on this part:
I flashed to a new ROM just to find out that i didn't like the content so i wanted to flash back to TOUCH X.
I did the usual stuff to flash my phone with, Hardspl, then bootloader etc. etc.
PROBLEM!
Now all my phone seems to be doing is go into bootlader and start updating. However, after 3 seconds i get the message that the update is complete. My phone resets itself, and i found out that nothing has changed. I tried it a number of other times, without results.
Now my question is: is there any other way to do this, this is obviously not working!
post all your ideas here so other people can read this in case that they have the same problem!
Everytime you flash a ROM, you do not need to hardspl your device, only once...I would reformat your memory card,use a stock original rom and see if it will flash with that....usually the issue you are seeing is because the nbh file is not being read properly, make sure your nbh file is named correctly.I have had the issue earlier in my days where if I copied the nbh file through active sync something gets screwed in the transfer...used an external card reader and copied it to my memory card after formatting it and it went through....just some suggestions....Good Luck
Regards,
WC
didn't solve it at all.
More suggestions?
SyntheticDistortion said:
didn't solve it at all.
More suggestions?
Click to expand...
Click to collapse
seems to be your problem? ---> CLICK
Nope, didn't do anything..
Any other suggestions?
EDIT: Really a lot of thanks for anyone helping, i really would love to start flashing again!
grateful for the help arnt you..
try flashing the USB method, if it works its probably due to your memory card. (unless ur already using the usb method, then try the memory card method!)
How do i use the USB method exactly?
And really guys, thanks for all the feedback, maybe make this a sticky for future reference?
SyntheticDistortion said:
How do i use the USB method exactly?
And really guys, thanks for all the feedback, maybe make this a sticky for future reference?
Click to expand...
Click to collapse
well what you do is download the file attached to this post (it is available in one of the stickies but when i tried to download it, it failed so i zipped this one up for you)
extract the .exe within to where your nbh file is (not on xperia, on computer)
make sure there is no KOVSIMG.nbh on your memory card!
put your phone in bootloader (tricolour screen) and plug in via USB
run the custom_RUU.exe and follow the prompts pressing next etc.
you don't have to sync via activesync 1st like it says.
ignore the version number of the ROM just make sure your using the correct nbh and flash!
urm i think you should at least try to look at the stickies .........
this is very useful. i had problem flashing using micro sd so all my flashes are via usb.
http://forum.xda-developers.com/showthread.php?t=497511
That seemed to have done the trick people!
Thanks very much and keep up the good work!

Categories

Resources