Anyone else having trouble with their car charger not charging their at&t tilt? I have 2 aftermarket car chargers from cellphoneshop.com and having problems. Im using DCS wm6.1 v1.5 rom and radio 1.64.06.04. I plug the charger in, the red light on the charge goes on, the orange light on the phone goes on, the battery status from quickmenu in the top right corner blinks on/off, the phone says its charging, but the phone isnt charging. The battery is going down like it normally would while all this is going on. Ive tried 2 different car chargers on 2 different vehicles and still the same problem. I dont believe its the car chargers since the 1st one i used is the one ive been using for the past 3 weeks now with no problems and the second car charger i tried is the same as the first but brand new out of the box both with the same problem. I just flashed to this rom today and this is the first time trying to charge my phone with this rom via car charger so maybe its just the rom? Im stuck at work til 11 so i cant test it on my usb or home charger til then. Any ideas or do u guys think its just the rom? Thanks! Ive never had this problem with duttys 2 newest roms, just this one i flashed back to today.
Sometimes the orange charging light on the phone will flash on/off super fast! Also sometimes the orange light will disappear and while its off the phone will still lie to me and say its charging.
is there anything running on the phone when you plugged it in? my phone wont charge after i've been using 3g for some time and it heats up. also is there any other device you can test the charger with?
XtreMe_G said:
is there anything running on the phone when you plugged it in? my phone wont charge after i've been using 3g for some time and it heats up. also is there any other device you can test the charger with?
Click to expand...
Click to collapse
Yes, i have java, hotmail, and palm messaging on in the background but having programs on in the background never made a difference before nor did being in 3g coverage which is what im in 95 percent of the day living in southern california. No other phones to try the chargers on. Ill try turning the phone off for a bit and charge it and see what happens. That would determine if the coverage or backgrounds apps are stunting the charge.
Im convinced its the rom now. When the phone is powered off the orange light is there showing its charging then after a few minutes disappears. I then unplug the charger and plug it back in but this time instead of an orange light theres a red light that stays on! I then unplug the charger and the second i unplug it the red light goes away and the phone turns on by itself. I dont think a simple car charger can do all that to a phone. I really liked this rom too. Oh well, just gotta charge my phone when i get home on the home charger if that works and reflash back to duttys march 08 rom.
Anyone else have similar car charging problems?
SOLUTION
It's not the ROM, it's the charger. Generic chargers are not wired the same as HTC chargers. HTC shorts pins 4-5 on the mini-USB end of the cable signaling the phone to enter into charge mode. Normal mini-usb chargers don't and so it's intermittent. If you purchase an HTC charger OR modify a cable the problem will be solved.
If you have other HTC phones, you'll see similar issues, especially when the battery is <10%.
The phenomenon is pretty well documented elsewhere on this site.
Regards,
liquidsilver said:
It's not the ROM, it's the charger. Generic chargers are not wired the same as HTC chargers. HTC shorts pins 4-5 on the mini-USB end of the cable signaling the phone to enter into charge mode. Normal mini-usb chargers don't and so it's intermittent. If you purchase an HTC charger OR modify a cable the problem will be solved.
If you have other HTC phones, you'll see similar issues, especially when the battery is <10%.
The phenomenon is pretty well documented elsewhere on this site.
Regards,
Click to expand...
Click to collapse
Huh, you could be right because the stock home charger that comes with the phone works perfect charging. So do i have to buy a ridiculus $40 car charger then from at&t? Guess its too good to be true when the generic is only 4 bucks.
i use my car charger all the time when i am driving and i dont expereince any of these problems... aside from the fact that it chrages slower then the AC charger but its understandable...
liquidsilver said:
It's not the ROM, it's the charger. Generic chargers are not wired the same as HTC chargers. HTC shorts pins 4-5 on the mini-USB end of the cable signaling the phone to enter into charge mode. Normal mini-usb chargers don't and so it's intermittent. If you purchase an HTC charger OR modify a cable the problem will be solved.
If you have other HTC phones, you'll see similar issues, especially when the battery is <10%.
The phenomenon is pretty well documented elsewhere on this site.
Regards,
Click to expand...
Click to collapse
Ive never had problems though with these generic charges with other roms and yes i've charged my phone from 0 to 100 percent on the generic car charger i have before. This is the first time ive charged my phone with this rom and with the car charger so thats why i would say its the rom since it has charged many other roms perfectly. Do you know of a good place to buy an htc offical car charger? The best i've seen on the web so far is 25 bucks.
I'm going to get one of the USB car chargers.
Even the chargers ATT sells can fail. They are just repackaged junk for the most part with low current ratings.
$25 is pretty good for an HTC charger. Highly recommended to go this route.
Those who have success with the generics are just lucky as the chargers don't meet specs. The odds are good that it will let you down someday.
As I mentioned above, there's a lot of info on this topic already posted elsewhere on the forum.
Got an official HTC Charger (in at&t packaging even) from eBay seller "NakedCellPhone" for $10 + about $5 shipping.
They're marked as for the Cingular 2125 & a few other older models but it works perfectly.
DOES THE HOME CHARGER (ac) WORK???
If so, it DOES & only USB to PC or Automotive charging is affected, you've most likely damaged your USB port pins while trying to soft reset.
Take a look at the USB port on the device. If it is curved or lower on the righ side, congratulations, you are both the Perp & the victim. The USB port was poorly placed by HTC, & the stylus was poorly placed by you.
Sometimes it can be (very gently & at your own risk) bent back into shape depending on which one of the two usb port versions your device has.
BTW, if you have a business account they are only $15.00
Not all chargers are the same.
The stock OEM charger has a rating of 1A. Most car chargers that I have seen have 500mA to 800mA rating. In most cases, with these lower current chargers, you won't notice a difference except for possible longer charging time. Though, if your battery is really low, <20% or so, your car charger may not work.
I have experienced this phenomenon not only on HTC devices like the 8925 and the 8125, but also the Siemens SX66 as well.
As a side note, I've read somewhere that charging using a USB cable to your computer allows for 500mA, UNLESS the PDA is syncing through ActiveSync when the PDA asks permission to draw 1A of power. If I remember correctly, the OEM charger shorts a couple of pins to simulate this situation, but of course, the power converter/inverter is also rated at the higher current as well.
I'm not sure shorting the pin on a lesser rated charger is going to have much effect, except possibly breaking your device or cable.
Cardyin
I just don't understand how the generic can charge my phone everyday for almost 3 weeks now then all of a sudden stop and acting so weird, see posts 2 and 3. Then i try my second generic car charger right out of the box and does the same thing. Yes, my phone charges perfectly through the usb on the computer and the home charger it came with so i dont think its the port on the phone thats messed up. Guess ill have to invest in an official htc car charger and see how it goes.
GSLEON3 said:
DOES THE HOME CHARGER (ac) WORK???
If so, it DOES & only USB to PC or Automotive charging is affected, you've most likely damaged your USB port pins while trying to soft reset.
Take a look at the USB port on the device. If it is curved or lower on the righ side, congratulations, you are both the Perp & the victim. The USB port was poorly placed by HTC, & the stylus was poorly placed by you.
Sometimes it can be (very gently & at your own risk) bent back into shape depending on which one of the two usb port versions your device has.
BTW, if you have a business account they are only $15.00
Click to expand...
Click to collapse
The 2 last pins on the right side are down just a notch from the rest of the port but its pretty much always been like that, even when the car charger was working. Only having problem with the car charger, computer and ac charging works fine. I'll try to move the pins up and align them but its so minor how much they are down.
cardyin said:
Not all chargers are the same.
The stock OEM charger has a rating of 1A. Most car chargers that I have seen have 500mA to 800mA rating. In most cases, with these lower current chargers, you won't notice a difference except for possible longer charging time. Though, if your battery is really low, <20% or so, your car charger may not work.
I have experienced this phenomenon not only on HTC devices like the 8925 and the 8125, but also the Siemens SX66 as well.
As a side note, I've read somewhere that charging using a USB cable to your computer allows for 500mA, UNLESS the PDA is syncing through ActiveSync when the PDA asks permission to draw 1A of power. If I remember correctly, the OEM charger shorts a couple of pins to simulate this situation, but of course, the power converter/inverter is also rated at the higher current as well.
I'm not sure shorting the pin on a lesser rated charger is going to have much effect, except possibly breaking your device or cable.
Cardyin
Click to expand...
Click to collapse
You guys think this charger is worth a shot or just pay the extra 20 bucks for the official? http://www.semsons.com/hipocarchwim.html It says its power output it 850mA!
Here is the cheapest original htc car charger i could find, www.talkietech.com/htcvecarpoch.html Heres some specs, OEM HTC Car Charger (81551) Features:
HTC Cell Phone Vehicle Charger allows phone to be charged on the road
Original Genuine HTC car charger guarantees maximum durability and performance
High quality aluminum brushed LED indicator light
Part# 81551
Compatible with:
HTC Cingular 8525, Cingular 8125, HTC Cingular 2125
HTC T-Mobile Dash, T-Mobile Wing, T-Mobile MDA and T-Mobile SDA
HTC T-Mobile Shadow, HTC Touch, Sprint Touch
It doesn't say though it works with the 8925 or tilt, would it still work on my at&t tilt? I think it would since my tilt's home charger charges my 8525 fine. What do you guys think?
deeznuts said:
The 2 last pins on the right side are down just a notch from the rest of the port but its pretty much always been like that, even when the car charger was working. Only having problem with the car charger, computer and ac charging works fine. I'll try to move the pins up and align them but its so minor how much they are down.
Click to expand...
Click to collapse
I can garuntee they didn't come "down just a notch". There ar multiple threads about this issue. Sometimes it causes auto chargers to fail completely & somtimes it just causes a bad connection.
When the device was new, it was straight as an arrow. I know this because I have a TYTNII & a Tilt & this happened on the Tilt. I would drive into the local store & tell them you are having charge issues. They'll let you test out one of the stock chargers, & if that doesn't work, then it's a connection issue because of the mis-shappened port. The pins in the USB port are pretty small. It does NOT take much deviation for them to lose good contact. It also happens more frequently on the devices that have the open ended pin block.
Related
Okay, I'm stumped. I'm already getting a replacement device from HTC under warranty so my problem is solved, but like many of you, I HATE NOT HAVING AN EXPLANATION FOR THINGS!
I'm also wondering if anyone else has had this problem? About 10-Days ago my Kaiser (Tilt) stopped charging via the automotive charger. The A-C charger works fine, but the vehicle charger sent to me with my device from AT&T completely stopped charging my device. I went to the AT&T store & bought a new charger, It didn't work. I changed power points, & cigarette lighter in the vehicle &, it wouldn't work. I tried the charger in the vehicle of two different AT&T sales guys & also tried multiple chargers, & it wouldn't work. Is there any reason why the unit would lose it's ability to charge via a vehicle charger while still retaining it's ability to charge through USB to computer & through the A/C home charger? It seems to me that if the charge portion of the MB was fried, then all charging would be affected.
So how can my device charge fine through all means EXCEPT the vehicle charger?
Again, AT&T is sending me a new device, but I hate not having an explanation for the problem, drives me Nucking Futs!!!
Any ideas, anyone?
Thx!
I dont want to sound rude but have you checked your power settings?
Under the "Advanced" it has a option for "When device is turned on, do not charge the battery when connected to the PC."
If this is ticked it will not charge via the in car charger.
It's a known issue, not just with the Tilt
I had the same problem with my Axim X50 and X51v.
The original sync/charge cable wouldn't charge from the car's lighter, while non-branded cables did so without any problems at all.
This happened with other Axims as well, so I know that it wasn't a defective unit.
I then purchased an HP Ipaq HW6910, and encountered the same issue with my wife's Mazda 5 - the HW6910 woudn't charge if the cable was connected to the charger, when I started the car. It only worked if the adapter and cable were disconnected while staring the car. This did not happen with my Mazda 3 or my Mitsubishi.
And another thing I discovered, is that some cables are not designed for use with car chargers, but they work perfectly with AC chargers.
I bought a couple of retracting sync/charge cables for my HW6910, they worked only when connected to the mains. But regular cables worked perfectly with both power sources.
Jygar said:
I dont want to sound rude but have you checked your power settings?
Under the "Advanced" it has a option for "When device is turned on, do not charge the battery when connected to the PC."
If this is ticked it will not charge via the in car charger.
Click to expand...
Click to collapse
OF COURSE I DID.
Yeah, It charges fine from the PC, & from an A/C source. But the HTC TYTNII car charger that came with my device, as well as replacement car chargers don't work.
wisniak said:
I had the same problem with my Axim X50 and X51v.
The original sync/charge cable wouldn't charge from the car's lighter, while non-branded cables did so without any problems at all.
This happened with other Axims as well, so I know that it wasn't a defective unit.
I then purchased an HP Ipaq HW6910, and encountered the same issue with my wife's Mazda 5 - the HW6910 woudn't charge if the cable was connected to the charger, when I started the car. It only worked if the adapter and cable were disconnected while staring the car. This did not happen with my Mazda 3 or my Mitsubishi.
And another thing I discovered, is that some cables are not designed for use with car chargers, but they work perfectly with AC chargers.
I bought a couple of retracting sync/charge cables for my HW6910, they worked only when connected to the mains. But regular cables worked perfectly with both power sources.
Click to expand...
Click to collapse
Funny, I just ran out to the truck & grabbed one of the guys Blackberry chargers & it looked like it was working. But SK Tools reports an even bigger (negative) amp draw (like discharging twice the normal rate). So with the BB charger it dischages even faster. Maybe reversed polarity Guess I should've checked first. That's a moot point now though as I await my new unit. Weird though.
Well i was using a BB charger that worked fine up until this morning. i bought my phone when it first came out so it wasnt easy to find a charger made for it at the time. i never had a problem until today. i also noticed that the Usb terminal on my device was bent. i called htc but they charge way too much to fix it. i have no idea how or when the terminal broke but it does still charge when pluged into pc or into the wall. ill have to spend $80 to have ppctechs fix it.
wassup, i`m in SF Cali, I had a att 8525 that was doing the same thing. I assumed it was the phone when it 1st started happening. After a week or so it was bothering me so i started playing with it trying to figure out if it was a setting, bad flash, or hardware. I noticed that if the phone was off it wood charge but not if it was on. I started flashing my phone and testing (for trouble shooting purposes) and for the first 2 or 3 roms problem still existed, then one of the roms i flashed to would turn on the back light as if it was charging but no LED or charge, when this started happening I realized that if i turned my fone off it wood start charging and continue to charge when i booted the fone back up. So if when i got in the car i pluged in/ shutdown/ waited like 45 sec or 1 min. / then booted it would temp. fix the problem for as long as my fone was on the cable. At some point after that many weeks/roms later i noticed it was working correctly again, So I had decided it was a glitch in the rom, But i`m not a Dev. or fone guru so I really dont know what it was, but hope this helps someone.... PEACE!! ~bboyphrog1~beatz`n pieces krooh~
flexte said:
Well i was using a BB charger that worked fine up until this morning. i bought my phone when it first came out so it wasnt easy to find a charger made for it at the time. i never had a problem until today. i also noticed that the Usb terminal on my device was bent. i called htc but they charge way too much to fix it. i have no idea how or when the terminal broke but it does still charge when pluged into pc or into the wall. ill have to spend $80 to have ppctechs fix it.
Click to expand...
Click to collapse
The slight diagonal slant on the bottom right? It's supposed to be like that. All AT&T Tilts (and I'd assume TyTN II's, but I've never had one to compare) have a mini-usb port that looks that way.
i looked at a 8525 and the usb terminal was straight. i even took a pencil and straightened mine out. it should be bent. that wouldn't make sense because the charges slot is not bent. i think the problem is that one side of the terminal is not soldered to the board and can easily be broken. in another thread 3 people have the same issue. as far as the car charger goes ill do some testing but until today it was charging fine while the phone was on.
this issue is known ,it even happens with the htc tynt.... by simlpy rebooting while in the charger it starts working again ..at least with mine.
I've had the same problem. I went to the lcoal AT&T store and they said they never heard of it so I thought it was just me. It looks like many of you have the issue. I wish I knew what it was. It was really bad with my 8525,
i thought Faria developed a cab to fix this issue in the hermes forum? might be worth having a search for it and when i get home i will see if i have a copy on my pc.
any of you guys get anywhere with this? I have exactly the same problem. posted in a couple of other threads actually.
Not sure whether the usb port is damaged, but it's certainly is slightly "down" on the right hand side.
It charges perfectly on the mains and perfectly from usb, but not in the car.
I have used a normal car charger, spent £50 on a Carcomm powered mount and tried one of the separate chargers that you plug the standard mini usb cable into. Nothing works. This is driving me crazy (if you'll excuse the pun!) a the primary reason I bought the Kaiser, was for GPS.
Thanks
well i also just found out 2 of my minisync cables dont work anymore. 1 of them still charges the phone but neither of them sync the phone anymore. it still syncs fine through a normal usb cable.
I am using a moto Razr car charger and it works fine so far.
Okay, confirmed on my replacement Tilt: The USB port is arrow straight. Someone earlier mentioned it being lower on the right side & indeed my DEAD DEVICE was as such. Looks like a bad job of connecting the port to the device.
NOTE!!!!!!
It's a good idea to take a look at your charger before you plug it in to make sure the charger USB connector is not bent or mi-sshappened.
i have the same problem i went through 4 att car chargers adn 5 phones. They are crap. Its not the phone its the charger if you play with it you will see that it comes and goes. The end tip on the charger is bad doesnt make a good connection. i have yet to find a good car charger.
Mine stopped charging using the car charger supplied and a brodit. A friend's kaiser charges OK with the same chargers.
No-one has mentioned it in this thread, but my phone, shows "charging" in the battery control panel and the LED lights up to confirm this. The percentage charge value decreases as though it isn't being charged!
As others have done I noticed that the corner of the plastic centre of the connector nearest the reset hole was slightly bent and I assume (though can't remember doing so) that I missed the reset hole with the stylus tip and pushed it in. Menu driven resets for me from now on!
HTC Europe didn't know anything about this fault, so seem to be happy to repair / replace it under warranty. It's with them at the moment, so I'll have to wait and see.
RSVRover
faria said:
this issue is known ,it even happens with the htc tynt.... by simlpy rebooting while in the charger it starts working again ..at least with mine.
Click to expand...
Click to collapse
that didnt work for me. only one of my chargers work now.
RSVRover said:
Mine stopped charging using the car charger supplied and a brodit. A friend's kaiser charges OK with the same chargers.
No-one has mentioned it in this thread, but my phone, shows "charging" in the battery control panel and the LED lights up to confirm this. The percentage charge value decreases as though it isn't being charged!
As others have done I noticed that the corner of the plastic centre of the connector nearest the reset hole was slightly bent and I assume (though can't remember doing so) that I missed the reset hole with the stylus tip and pushed it in. Menu driven resets for me from now on!
HTC Europe didn't know anything about this fault, so seem to be happy to repair / replace it under warranty. It's with them at the moment, so I'll have to wait and see.
RSVRover
Click to expand...
Click to collapse
Please let me know the outcome. mine is getting worse by the day.
Now I'm confused.
Because the device charges over USB I just assumed it would draw <500mA (the max output of a USB port) but the specs say it draws up to one amp.
Having owned a high-drawing device before (Axim x50v) I know that trying to pull this out of a USB port can blow your motherboard. So are these safe to charge over USB??? How does the device know whether its being charged over USB or mains - are there different charging pins on the connector?
Hi to all!!.
Let's see if someone out there can give me a reason or a solution for my problem.
This weekend I went on a long trip and I found that if I use my TomTom while charging the Kaiser (regular car charger) at some point the PDA stopped charging and showed the "low battery" icon. The only way to get it charging again is doing a soft reset (with the device unplugged) and then plugging it again.
This is quite annoying since it's impossible to do this while driving since I need the GPS to get to my destination (this is the reason to have GPS, right!?)
any solutions??? I would be eternally gratefull if someone gets me out of this!
Thanxs in advance.
What is the current rating of the charger? When I used a cheap charger made for the RAZR I couldn't keep a positive charge when using GPS and sometimes it would stop charging and I'd have to disconnect and re-connect it. Didn't have to reset though. I suggest you get a higher current charger made for the Kaiser.
marc
I had this problem too and I simply changed the charger. Also, make sure that you see the "charging" icon with the electrical cord displayed when the device is connected.
I've had similar problems using several different car chargers.
When looking at the charger specs, I saw they all had a 1000mA current maximum. When I found a HTC charger for the TYTNII I immediately looked at the specs, and behold: 2000mA max. current
With the HTC 2000mA charger I haven't had any problems sofar. A week ago I drove 3000km using my TYTNII with tomtom and Charging/navigating went fine.
Yes... that may be the issue, I'm not using a cheap charger, I'm using the cheapest charger I could find!!!! jajajaja
And in fact it was done for the V3 RAZR... so... I'll try not to be so mean and buy a good one!.
I will tell you if this worked!... Many thanxs!!
I thought this was just happening to me as no-one posted about it 'til now!
Mine is from mobilefun, supposedly fine for a Kaiser, but i guess it's not.
There's no details on the product page about what current it can draw, but at £7 i think i may need a better one.
Can anyone point me to a site that quotes the rated mA for their products?
It's definitely the charger. I got 2 cheap ones from overseas for about $1 and I use it to charge up my psp and kaiser. The home adapter can't charge up the psp but only the phone and the car adapter can charge up both at the same time with no problems. And its using the exact same cable as well. So its definitely the adapter.
I agree 100% - I bought a cheap charger from eBay, but it would not charge the phone when using TomTom - and barely hold the charge when playing MP3s. I replaced witha genuine HTC charger and everything is fine
Your mileage with HTC original chargers may vary
The idea of using an original HTC charger for some reason seems popular here. The original charger that came with my 'sealed box' TyTN II lasted 4 charges (about 2 weeks as I'd charged by USB cable the rest of the time) before it made a loud click and the light extinguished for the last time. When I called HTC to ask whether a different model of replacement could be provided I was told I would only receive another charger of the same model. Not wanting to have the possibility of regular failures (and this thing did look cheap and nasty), I bought a different charger for £8.95 and that ones been going fine since. The one I now have is shiny and black (matching the TyTN II casing perfectly) and it came with a set of different interchangable 'prong adapters' so I can use it in the UK, USA, Europe and Australia
For a multiband top of the range phone like the TyTN II, why didn't the manufacturers supply these in the first place. My rating of the original HTC TyTN II charger that came supplied with my UK sourced device in Sep 2007 is 0 out of 10
I bought a 300W inverter from Maplin for £20 and use the three pin plug charger that I use in the house...
hmmr said:
I've had similar problems using several different car chargers.
When looking at the charger specs, I saw they all had a 1000mA current maximum. When I found a HTC charger for the TYTNII I immediately looked at the specs, and behold: 2000mA max. current
With the HTC 2000mA charger I haven't had any problems sofar. A week ago I drove 3000km using my TYTNII with tomtom and Charging/navigating went fine.
Click to expand...
Click to collapse
Could you let us know where you got this charger? I think I am running 700mA in the car, which is a SLOW charge... Thanks for the help...
I've bought the charger in a local store, but after some googling, i found it HERE
If you click on the picture to enlarge, you can just make out the max current (2A) on the label.
Using HTC part no. 81551 should give you plenty of results
Well mine also just developed this problem. Drove 130 miles in one day a couple of weeks ago (using Tomtom) and my old tytn 1 car charger worked fine. Then a week ago drove 40 miles using same charger and when I got where I as going I found the battery was almost flat and the phone was really hot! So did a search and found this appears to be a common problem with this phone. (Although I can't understand why it worked fine when I did the 130 mile drive!)
Anyway have taken the plunge and bought a genuine HTC car charge. First off, as others have said, I can confirm that it has a 2amp rating (my other one was rated at 1amp). Went out with it for the first time today for a short journey to a shop to test it using Tomtom. After 5 mins it did the same as my old one, the charging light went off and battery stopped charging. However after my shopping (bought something for my kids who have chicken pox currently!) I went for a 15 min drive and it worked ok, actually charging throughout and increased my battery by about 3% (from 74% to 77%).
So the upshot is - I don't know what the heck is going on - could be that my battery or phone got itself into a mess with the first charger and took a while to recognise the new one - or it could be an intermittent problem!
What I do know is that I am shortly doing a 1000mile round trip and I need it to be reliable - so will do more testing over the next few weeks and let you all know how it goes. Its still under guarantee so any more nonsense and it will go back.
In the meantime if anyone has any further info on this please post.
Cheers
Barney
Barneyabz said:
Well mine also just developed this problem. Drove 130 miles in one day a couple of weeks ago (using Tomtom) and my old tytn 1 car charger worked fine. Then a week ago drove 40 miles using same charger and when I got where I as going I found the battery was almost flat and the phone was really hot! So did a search and found this appears to be a common problem with this phone. (Although I can't understand why it worked fine when I did the 130 mile drive!)
Anyway have taken the plunge and bought a genuine HTC car charge. First off, as others have said, I can confirm that it has a 2amp rating (my other one was rated at 1amp). Went out with it for the first time today for a short journey to a shop to test it using Tomtom. After 5 mins it did the same as my old one, the charging light went off and battery stopped charging. However after my shopping (bought something for my kids who have chicken pox currently!) I went for a 15 min drive and it worked ok, actually charging throughout and increased my battery by about 3% (from 74% to 77%).
So the upshot is - I don't know what the heck is going on - could be that my battery or phone got itself into a mess with the first charger and took a while to recognise the new one - or it could be an intermittent problem!
What I do know is that I am shortly doing a 1000mile round trip and I need it to be reliable - so will do more testing over the next few weeks and let you all know how it goes. Its still under guarantee so any more nonsense and it will go back.
In the meantime if anyone has any further info on this please post.
Cheers
Barney
Click to expand...
Click to collapse
I too have had similar problems. Bought a quality Brodit (Active) car holder with charger and it seems to charge for only about 30s-1min. The orange charge light only stays on for a short while and then then battery runs down!
Interestingly the charge indicator on the screen always shows that the device is being charged whilst connected in the car - even though the orange charge light has gone out. I've posted this in the general area for kaiser and also in the ROM area applicable (Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700) in case it may be ROM specific.
Another person reports no issue with the same charger as mine and the same ROM - it's all very annoying because there would seem to be too many complaining about such issues. The output amperage may be the issue but surely the Brodit (which is good quality) charger should be fine?
I will post whan I get this issue solved but I wonder if there is something in the Registry that can cause such issues too - I agree the output limitations are also of relevance (I just cannot believe that this is my issue).
Well I have been using the official HTC charger for a month now without any problems, only thing I would say is that my journeys have all been short (under an hour at most). however using my old charger it would die after a much shorter period so problem does seem to be resolved.
cheers
Barney
Temperature
Hi.
I had the same problem, with a different GPS software. Check the temperature of your device ( you can use a software called " Battery Status ". In my kaiser it never showed me a bubble ( like some other ROM ) that it reached 47C and then the phone automatically stops the charge.
The heat is from actual charging + the sun. I have a window mount and the phone was on it when I was charging. Take all into account and you will see that it will over heat quite fast.
I solved the problem by putting the phone in a shaded place when charging it. It also helped if its next to the vent, but don't cool it to much, because if you do then when you use the AC and you go out, some of the connectors of the phone will get corrosion on them ( SIM, USB, SD etc.) .
Good luck.
There are 2 reasons: The first just got mentioned, overheating by the combined effect of the device heating up itself and other factors like the sun. If the battery heats up too much, the safety system will stop charge, and the battery will then be drained until empty. No soft reset needed, but the device has to be cooled to the appropriate temp and the charger disconnected/reconnected. I was also having that issue when using my older Hermes with 3G sharing over wifi and downloading hard, even with the battery cover removed and the keyboard open the device was heating so much on itself it would cause that. The Kaiser seems to heat less when doing the same BTW.
The second is that when using a common charger (not HTC branded), even if it is rated at 2 amps the phone won't be drawing those 2 amps from it but will limit itself to about 500mA.
The reason is simply that it's being charged from a USB port, and a USB device is not allowed to draw more than 500mA from a USB port. HTC chargers have a chip inside and tell the phone that they are official chargers from which the phone may draw more. Without that identification the phone stays in low current mode.
On the Hermes it was even simpler, if you connected a generic charger it would not charge at all. It would only accept charging from an active USB port it was able to have a communication with, or the original charger.
So, use original HTC chargers when current draw is high. The Kaiser with GPS, full backlight and a GPS program running will draw something pretty close to the 500mA.
I used to be cheap on charger too until I used the battery sucker Dell Axim x51v (612mzh, VGA, BT) on my car. The I brought the 2A ecovell usb charger and my problem solve.
tony.wheeler said:
I too have had similar problems.
Click to expand...
Click to collapse
Have you seen this thread yet? http://forum.xda-developers.com/showthread.php?t=343951
Looks like that may be your issue. Saw a chap in the phone shop (in High Wycombe) the other day with a TyTN II with faulty USB port. Must be a common thing around the area but as I don't have a car to put a car charger into, it won't affect me!
Original charger
I had the same charging issue and solved it with an original htc charger, cheapest i could find was on Amazon for £12 delivered:
http://www.amazon.co.uk/Original-HT...1?ie=UTF8&s=electronics&qid=1214645330&sr=1-1
What exactly is the scoop on this? Is it that they overpower the charging circuit (everyone says they charge the phones faster)? Is there a way to tell you're about to do damage?
I don't use the car charger that came with my Kaiser, I have several generic chargers which all work just fine. However I noticed that when running GPS, although the charge light was on, the battery wouldn't really charge. It wouldn't discharge either, I put it up to the extra drain on the phone's power system.
The other day though, my phone... stopped charging? I was driving (GPS) and the phone suddenly beeped a critical battery warning, the charge light was off... but the power was plugged in and the charger's power light in the cigarette socket was on. It WAS making a connection to the phone: if I unplugged it the screen would go dimmer, if I plugged it back in it would get brighter. But it still seemed to be running off the battery, which was draining regardless. The moment I got to my destination, it all powered off. Is this a forewarning of darker circumstances to come?
from what I've read you should not be using generic chargers. The amperage could differ. Therefore, if the electricity in your vehicle spikes you could be riding with a paper weight.
In addition, it is common that your device will not charge (nor discharge) while running your gps application. I play monopoly often while my phone is in the charger and my device usually doesn't charge while I am playing.
Also, I think the pinout on generic USB chargers are different. The ones that are for Moto Razr / Blackberry phones dont work to charge the phones ( as I have a work blackberry and tried it) It didnt hurt my phone, however it just didnt charge. I have heard of others damaging but if its not made for the kaiser, I wouldn't try it.
I've never had access to Moto Razr / Blackberry chargers. While I can't speak for those, I know generic USB chargers would have exactly the same pinout as the stock Kaiser charger. The amperage supplied may indeed differ, I think that might have explained my issue above. It was almost like the charge circuit 'gave up' since the phone was demanding as much/more power as it was getting.
CrArc said:
I've never had access to Moto Razr / Blackberry chargers. While I can't speak for those, I know generic USB chargers would have exactly the same pinout as the stock Kaiser charger. The amperage supplied may indeed differ, I think that might have explained my issue above. It was almost like the charge circuit 'gave up' since the phone was demanding as much/more power as it was getting.
Click to expand...
Click to collapse
My razr charger works perfect with my tilt.. (MOTOROLLA branded - not generic)
Ditto on the motorola razr charger;Have an old razr charger I use it for travelling instead of unplugging my original;works fine!!
+2 on the Motorola branded car charger...charges my Tilt just fine. Now I'm paranoid, though...
CrArc said:
What exactly is the scoop on this? Is it that they overpower the charging circuit (everyone says they charge the phones faster)? Is there a way to tell you're about to do damage?
I don't use the car charger that came with my Kaiser, I have several generic chargers which all work just fine. However I noticed that when running GPS, although the charge light was on, the battery wouldn't really charge. It wouldn't discharge either, I put it up to the extra drain on the phone's power system.
The other day though, my phone... stopped charging? I was driving (GPS) and the phone suddenly beeped a critical battery warning, the charge light was off... but the power was plugged in and the charger's power light in the cigarette socket was on. It WAS making a connection to the phone: if I unplugged it the screen would go dimmer, if I plugged it back in it would get brighter. But it still seemed to be running off the battery, which was draining regardless. The moment I got to my destination, it all powered off. Is this a forewarning of darker circumstances to come?
Click to expand...
Click to collapse
That is the exact same thing I am experiencing with my Tilt.
Tilt is charging from a generic car-to-USB and USB cable.
I start TomTom.
Charging works fine for a while.
Then suddenly the charging stops and the battery is drained.
I found only two ways to get it to charge again:
1. Turn off device with TomTom charging; hold Tilt against cool air flowing from AC; plug into charger (while still off) ... then the phone turns on and charges.
2. Take out the battery; put it back in ... start phone.
It does seem that either the phone can draw power faster than a USB charger can supply it or the use of wifi and gps whilst charging overheats it. I particularly see this behavior when I'm running tomtom and navizon. The phone seems to remain charging longer in cooler weather or if I point an air vent at it. My current no wifi woes started after an occurrence of just this behaviour the other day.
RAZR chargers don't have enough current and it doesn't keep a positive charge when using the GPS. It says it's charging but ultimately it goes down. Sometimes it stops charging and I had to unplug it and plug it back in. Use a charger made for the Kaiser. The charger from my brother's bluetooth GPS works fine though.
I have a generic USB cigar lighter adapter which I have been using to power mine with no problem. The only way I can see a charger frying a phone is if there is a voltage spike that isn't regulated.
The charger needs to be rated with an output of 5v 2amps which is what the electric charger is rated at. Bought one off ebay for $6. Most car chargers are rated quite a bit lower (400ma).
As the previous post states, some chargers are rated at under 500ma. This is not enough to change the Kaiser... I find that the Blackberry charger works fine, but sometimes takes a very long time to charge as the current isn't quite enough. I have a generic one at about 1000ma and that works fine.
USB from a PC is normally 500ma sustained.
I think there's another thread or 2 about this somewhere. I've been having the same problem with the Kaiser not charging via generic and razr car chargers.
After seeing the other thread I bought an HTC charger from ebay - at least it looks like one and is advertised as one! The sticker on the 'real' HTC charger only says 0.5 amp (same as the others are rated), but charges no problem with TomTom going.
I tried measuring the current using different chargers and PowerGuard and I think there is a definite difference (although not an easy thing to interpret). I notice the cable is significantly heavier on the real HTC charger (also coiled and tends to drag the phone from where I mount it a little). Others have said the pinouts are different too.
I looked for a 2amp charger but couldn't find one (if anyone knows a source?).
It's an intriguing problem but a 'real' HTC charger seems to fix it.
The other thread: http://forum.xda-developers.com/showthread.php?t=406771
There were a range of brodit car mounts with built-in chargers that bricked the kaiser. I bought one and it instantly blew it's fuse. I replace the fuse and it blew my kaiser up instead.
Assuming it was the kaiser I had it replaced, only for the charger to blow it up again.
Since then I contacted dsldevelopments (UK Distributor) who replaced it with an updated model. I have not had any issues after that.
I had this problem (Kaiser not charging in the car when GPS is on) and resolved it totally by getting the offical HTC car charger. Although output is 0.5A it is rated to 2A - my previous generic car charger was only rated to one amp and that would work fine as long I wasn't using GPS but once I ran GPS it just couldn't cope. Definately resolved this problem with the official HTC car charger (got mine of flea bay for £8)
cheers
Barney
I've had no problem with designed-for-Moto chargers and ones specifically designed to charge over USB from a dumb charger.
The problem is that drawing more than 100 mA without negotiating a connection with a PC violates the USB specification. Many manufacturers have gotten around this by finding other ways to signal the presence of a "dumb" charger, telling the phone it can draw more than 100 mA.
In the case of Mini-USB devices like the Motos, Blackberries, and HTC devices, the Mini-USB connector has a fifth pin that is normally not connected. If the charger plug grounds this pin, it signals to the device that it is permitted to draw more than 100 mA without a PC connection.
If you get a charger that does not ground this pin, an HTC device will not charge rapidly, if at all. (Typically only charges slowly when screen is off). This is why you get two cables when you order a single MiniSync from BoxWave, for example. They give you one "Sync and charge from PC" cable (no pin grounded) and one "Charge only" cable (pin grounded for dumb chargers). (If the pin is grounded it interferes with data communications for most devices.)
I use a motorola charger, which is fine if you do not use GPS.
when I use the GPS after some time the battery is very hot and stops load, but if I put the cell in front of the AC, just cools again to load.
I think the problem is due to protection from overheating battery
Belkin Charger
I grabbed a Belkin charger for my KRAZR/RAZR phones and it seems to work just fine, even with GPS running. My official Moto one also works fine with the tilt in GPS mode.
I do notice, though, that no matter what I'm using to charge it with, with GPS it gets hot. Since Li-Ion batteries are supposed to stop charging at a certain temp, it's possible that the combination of a lower grade charger and the heat generated by using GPS/WiFi/Cell at the same time (or any combo of the three), might be the issue.
I'm creating a new thread because I think my charging issue is unique...
My Kaiser will show an orange light and indicate that it's charging when:
1. Powered On and plugged in to: USB, AC power Adapter, or Car charger
but it will not take a charge and the orange light goes out after about two minutes.
2. Powered Off and plugged into: USB, AS Power, or car charger
but the orange light remains on and it never charges (tried 5 hours)
The device also does not sync, I don't see anything physcially wrong with the USB port, but it was damaged by water several weeks ago, it hasn't worked properly since.
I've been getting by with an external battery charger that I purhcased from Ebay.
Does anyway have any ideas? I've reflashed the device since then as well and there is no change in how it reacts to charging..
Hi echofive
I have the same problem with my Kaiser but at least it charges with just one of my 5 AC power adapters. Not in my Car charger and not on a USB connection.
Maybe it has something to do with the small USB pins on the Kaiser which are not properly aligned. You can try to bend them.
Good luck.
Hello, I was having this same issue and (long story short) I believe that it is the small USB pins on the phone.
Here is what I found (sorry knda long post). I have two ATT TILT phones. My Original Tilt phone got soaked in water but I was able to almost salvage the phone by soaking it in Denatured alcohol and letting it dry. This 'wet' Tilt has all functions but cannot read sim cards. It does however charge perfectly.
The replacement Tilt I have works like a charm but refuses to charge. Regardless of USB charging, off the wall charger or car charger, the orange light comes on, says it is charging but in 2 minutes the light goes out. The phone is still listed as charging but I know it is not charging because the battery level continues to drain. The phone does sync to my PC and I am able to transfer files to/from my new TILT via a USB cable. Just cannot charge the device.
I have 3 batteries. 2 stock batteries and the large 3200mah battery. All three batteries will not charge on my new TILT. I tried charging it via USB connected to my Computer, Car cigarette lighter, Car inverter charger, official TILT charger from CINGULAR ATT. Completely unable to charge the device.
If I attempt to charge the batteries (all three of them) on my old 'wet' TILT the batteries charge regardless of what method I use. It will charge via USB connected to the PC, USB connected to wall charger, official ATT TILT charger, or car charger. No issues. So I know the chargers, cables and batteries do charge on a TILT. Both TILTs are official ATT TILT devices. Two of the batteries are stock and 1 of the batteries is a SEIDO 3200mah.
Sometimes I get lucky and the new TILT phone does charge. In these cases I charged the phone using the Wall charger and the battery was over 50% capacity.
Now I know the new Tilt USB port is working because it syncs to my PC just doesnt charge after 2 minutes (light goes out) and battery continues to drain (watched and tested this after 3 hours of observation). I ended up ordering one of those TILT USB connectors which have a 3.5mm headphone jack and USB port.
This device: http://www.amazon.com/i-Trek-Stereo...8&s=musical-instruments&qid=1230877732&sr=8-4
What is weird is that I can now charge my NEW TILT using the USB port on this connector with this connector attached to my new TILT. If I attempt to charge the TILT using the onboard USB port, it stops after 2 minutes and the light goes out.
Personally, i think it has something to do with the pins. Hope this helps someone.
Jinkage said:
Regardless of USB charging, off the wall charger or car charger, the orange light comes on, says it is charging but in 2 minutes the light goes out. The phone is still listed as charging but I know it is not charging because the battery level continues to drain.
Click to expand...
Click to collapse
Been there, had that problem and the solution was even simpler and didn't involve the charging/USB port at all. Get a cotton bud (US folks call them Q-Tips) and spray some contact cleaner on it (not anywhere near the phone) and use it to carefully clean both the gold strips/terminals on the batteries along with the gold spring terminals on the phone. Although they may look clean, invisible grime film can make the connection fail and cause this problem. This is also a good tip to follow with ordinary household battery rechargers and NiMH cells. I haven't had this problem since but still carry out a terminal clean every few months to be on the safe side.
My phone wouldn't charge anymore. Searching through threads I found a magnificent magnified picture of the mini-USB port and the way the right part of the port was bent down a little. It was exactly like that with my phone, I used the pointing stick to tilt it up a little (be careful it may break of the pins, and that would lead you far from home!), which fixed! Haven't had the issue since!
Regards,
Nika.
Hi.
Have you still the link with the picture . I have the same problem an i am afraid , that i can kill my Kaiser
Regards
Dariely
Nope, sorry...
I had a similar issue with my Kaiser. It would charge with a USB cable and an ac adapter but not in the car. It used to but stopped. I took a dental tool and lifted the two little legs inside on the bottom of the mini usb port so they would contact the charger again and all is well.
nikagl said:
My phone wouldn't charge anymore. Searching through threads I found a magnificent magnified picture of the mini-USB port and the way the right part of the port was bent down a little. It was exactly like that with my phone, I used the pointing stick to tilt it up a little (be careful it may break of the pins, and that would lead you far from home!), which fixed! Haven't had the issue since!
Regards,
Nika.
Click to expand...
Click to collapse
YEAH!
Great Tip!
had the same issue as you a long time!
tilt up the pins: no more problem!
THANKS A LOT !
I straightened up the last pin. I was beginning to think it was my AC Charger...I plugged it in my Ashtray charger and it charged without a problem. I will see if this takes a charge. I didnt use any denatured alcohol, I just took the compressed air canisters used for computers and cleared out the usb port....
we wait now
Has anyone else had an experience with the G1 not charging when on a car charger and running bluetooth and the GPS. I thought I had seen a thread once about this issue, but cannot find it.
I went on a long trip and used my G1 and copilot. After about 6 hours my phone was dead (slower than if it hadn't been plugged in I suppose).
Granted I am using an old HTC Kaiser charger, but that shouldn't have anything to do with it. Is it possible or even likely that the charger isn't putting out enough amperage to overcome the current drain imposed by so many radios running? The charger was also very hot. When I turned my phone off (actually it was off because it was out of power), it charged fine.
pinetreehater said:
Has anyone else had an experience with the G1 not charging when on a car charger and running bluetooth and the GPS. I thought I had seen a thread once about this issue, but cannot find it.
I went on a long trip and used my G1 and copilot. After about 6 hours my phone was dead (slower than if it hadn't been plugged in I suppose).
Granted I am using an old HTC Kaiser charger, but that shouldn't have anything to do with it. Is it possible or even likely that the charger isn't putting out enough amperage to overcome the current drain imposed by so many radios running? The charger was also very hot. When I turned my phone off (actually it was off because it was out of power), it charged fine.
Click to expand...
Click to collapse
yes, i know exactly about it...i have 2 G1's and noticed that my generic mini usb charger in my truck only worked on 1 of them, i bought a new t-mobile one and now they both work, its because of the allowed amperage of the charger, the g1 requires more for charging purposes. just go grap u a t-mob usb and ull be back in business.
I've got the car charger from tmobile and on long road trips ill have google maps open following where im going and bluetooth on and connected to a headset and the brightness on max, and the phone charges just fine...well slowly of course.
Sounds like it maybe the charger, but i have no reason why cause you say it charges fine when the phone is off. Maybe try using a different outlet, or a different car and see if it fixes it.
yes veritasaequita,
I, too, think the amperage is too low. It will charge, but not with every radio the device has running (as they will be if you use a sat/nav and bluetooth while driving).
I guess I will grab a charger that is actually for a G1. Thing is, the AT&T Tilt (for which the charger is actually for)is a pretty demanding device as well. Would of thunk the charger adequate.
Most of the generic chargers you'll find online charge at .5AMP. Before buying one, make sure it's 1AMP so that it actually charges as if it were plugged into the wall.