Related
Hello Everyone,
I have a BA and I want to flash it but the power button dose not work..opened it up and found that the mechanism under the button has dropped and hanging on by a thread. The device works but I need the power button to get into bootloader mode.
So the question is this: is there a way to get into bootloader without using the powerbutton?
yolandanelson31 said:
Hello Everyone,
I have a BA and I want to flash it but the power button dose not work..opened it up and found that the mechanism under the button has dropped and hanging on by a thread. The device works but I need the power button to get into bootloader mode.
So the question is this: is there a way to get into bootloader without using the powerbutton?
Click to expand...
Click to collapse
From Jadel....
First, some advice. Several people have asked this question and it has been responded to in other threads. On forums, ALWAYS try and use the search function before asking. It might save you some time, and it also may give you further ideas or solutions to the problem. Now on to the response I gave someone else last year. Read the whole post.
IT IS POSSIBLE!
BUT DO THIS AT YOUR OWN RISK!!! I'M NOT RESPONSIBLE FOR ANY DAMAGED OR FRIED PDAs
I know because I myself have done it on an I-mate (Himalaya). It took some trial and error but I am now running WM6. In my case though, I had to completely remove the power button from the device. The previous owner dropped it on its head, and I got it for free, unfortunately most of the top is missing, including the power button.
SO, on to how I did it. I took a paper clip (metal) and put it about 1cm down, slightly to the right of where the power button used to connect to the motherboard. Make sure you have turned your XDA/IMATE on before doing this. You'll find that when you find the right area, your device will turn off, or the screen will go dark (like holding the power button for a second or giving it a quick tap).
If you manage to hold it there for the right period of time, while pressing the other bootloader buttons, then you will be able to enter bootloader.
This took me close to an hour to get just right, on both occasions I have done it, but it eventually worked.
Note: I have no idea how exactly this worked, but it did. My IMATE was useless without me updating the rom, so I had no worry about frying it if I did something wrong, that is why I was OK with playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.
Good luck.
If you have no clue just don't post!!
First off I have searched here and the internet as a whole and your suggestion didn't work! I have taken apart and modified to add a camera to my working BA ( yeah I got 3 of them) so "..playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.." is no worry of mine. Second off, if you had taken notice I have been on this board since Feb 2007 and I have only had to ask 3 questions, which means my searching skills might just be working on some level.
Maybe I should have been more specific: is there a software boot loader for the sx66?
David389 said:
From Jadel....
First, some advice. Several people have asked this question and it has been responded to in other threads. On forums, ALWAYS try and use the search function before asking. It might save you some time, and it also may give you further ideas or solutions to the problem. Now on to the response I gave someone else last year. Read the whole post.
IT IS POSSIBLE!
BUT DO THIS AT YOUR OWN RISK!!! I'M NOT RESPONSIBLE FOR ANY DAMAGED OR FRIED PDAs
I know because I myself have done it on an I-mate (Himalaya). It took some trial and error but I am now running WM6. In my case though, I had to completely remove the power button from the device. The previous owner dropped it on its head, and I got it for free, unfortunately most of the top is missing, including the power button.
SO, on to how I did it. I took a paper clip (metal) and put it about 1cm down, slightly to the right of where the power button used to connect to the motherboard. Make sure you have turned your XDA/IMATE on before doing this. You'll find that when you find the right area, your device will turn off, or the screen will go dark (like holding the power button for a second or giving it a quick tap).
If you manage to hold it there for the right period of time, while pressing the other bootloader buttons, then you will be able to enter bootloader.
This took me close to an hour to get just right, on both occasions I have done it, but it eventually worked.
Note: I have no idea how exactly this worked, but it did. My IMATE was useless without me updating the rom, so I had no worry about frying it if I did something wrong, that is why I was OK with playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.
Good luck.
Click to expand...
Click to collapse
I lifted this directly form another site I have subscribed to
http://relaysgoldens.com/sx66/tools/ROM_Update_Tools.rar
I have tried several times to hard reset using proceedure described, but the phone just restarts.
Help!
http://forum.xda-developers.com/showpost.php?p=2480910&postcount=4
Cannot hard reset as shown.
The phone does not show reset message & justs restarts, like a soft reset.
it happened to me also. i thought i can not hardreset but the problem was i was doing it wrong.
my recommendation to you:
try and do it without the back cover. to push the reset you need to enter yr stylus in an angle. that together with the use of the other hand (two fingers) make it hard to hard reset (pun intended). i found that i can do it much easier without the back cover or (also highly recommended for ppl with small hands) ask somebody to help you (three hands method ).
make sure you are pressing the volume down button.
also: keep pressing all three points for 1 sec then first release the reset button and keep the other two pressed for 1 second more before releasing and for god's sake do it over and close to a soft surface..., just in case.
i gave up. my phone is about to snap in half from me holding it down so hard. my hands are ****ing numb. what i think i'm doing is i move either slightly up or down while holding down the enter key and it becomes up or down instead of enter.
i did the settings-clear memory-1234 method but is that really the same as a physical hard reset.
i think i did **** up the phone, the usb connector interferes a little as it goes in the phone and activesync doesn't work anymore.
Try this procedure as another method.
Soft reset and the immediately press the volume down + round center button. Then follow procedure in grey menu to reset device back to manufacture settings. This is the same as a Hard Reset.
Good Luck and try not snap things, especially your device, lol
today's my first day with the phone, i really don't think i should ever try a physical hard reset again if i don't want to break the phone. activesync still works, whew...
mgs333 said:
today's my first day with the phone, i really don't think i should ever try a physical hard reset again if i don't want to break the phone. activesync still works, whew...
Click to expand...
Click to collapse
A Hard Reset doesn't brick the phone....
band27 said:
A Hard Reset doesn't brick the phone....
Click to expand...
Click to collapse
i wasn't talking about bricking the phone, but literally snapping the phone in half or something similar from pushing or bending the phone too hard.
anyway, i had a breakthrough today. previously, i was so intent on keeping the buttons pressed (especially the enter button) that i was pushing incredibly hard on the phone, making me feel like i was bending it too much.
and what was happening was that pushing it hard doesn't really help but rather hurt me because it was either being pushed as up or down (or even left or right) while pushing so hard.
the key for me was before pushing reset, to press it not crazy hard but press in directly straight and move up and down to make sure i'm not pushing up or down, and practice keeping it pressed in straight, then when i'm comfortable with that, (while keeping volume down pressed of course) then press the reset button.
and the grey hard reset screen should come up within a couple of seconds of resetting. so if it doesn't appear within a few seconds, let go of the poor phone and try again. previously, i had no idea how quickly that screen was to appear so i would hold it for 1-2 minutes while the phone was going through its booting process. hopefully this helps save some wear on your hands and fingers.
HTC BA WM 6.5 hard reset
Guys need your help also htc blue angel updated rom to windows mobile 6.5. I cant make a hard reset. wud like to know if there is a program for doin such. or any physical ways of having it done
Japsmate said:
Guys need your help also htc blue angel updated rom to windows mobile 6.5. I cant make a hard reset. wud like to know if there is a program for doin such. or any physical ways of having it done
Click to expand...
Click to collapse
http://forum.xda-developers.com/forumdisplay.php?f=244
Hi, I cleaned the screen of my HTC Diamond with a bit of alcohol and a pice of tissue and it seems that the alcohol got inside of the Power button. Now, every time I try to turn the screen on by touching the power button, it turns the screen on but it dispays a message that says: "Warning: Power will be turned off and you may lose data if you have not saved them. Do you want to continue?"
If I click YES, it reboots the phone, If I click NO, then its ok. That is fine, but the problem is when I want to turn the phone off. It's impossible. It will keep trying to reboot.
Does anybody know what can I do? I am really worried.
One solution could be to make some other button from the phone to act as the power button (like the Home button that is rarely used). How can I do that?
Please help!!!!
Thank you
Hi,
I have the same problem.
Did you already find an answer ?
No, I didnt find the solution. I tried to fix the hardware but didnt succeed. So, I created a dummy file to emulate the poweroffwarning.exe that pops up when you long press the power button.
Solution
Hello, I have one AT&T TITL 8925 that upgraded to Windows Mobile 6.5
After the new software was loaded I saw same behavior on my phone.
When the phone is ON and I pressed the power button sometimes it do not respond, and others I received the warning message "power will be turned off and you may lose data if you have not saved them..." My first tought was that it is because the processor is slow to this new software release, or maybe my phone is damaged. I was working perfectly with previous (light version) release so my final guess is that this sw requires more uses of the processos.
Anyways what I have been doing is before turing it off I press the red button or hang up button, and after this if I press the power button it works fine (No more warnings). I have some theories but I will keep doing the same
Hope this partial solution helps you as it does for me.
Regards
Jerry
this is not working for me :| the problem is i can't use my power button not even to open my display when it goes to sleep :|:| i don't know what to do guys please help me
You can use the Stylus to awake the phone, instead of using the power button. You can also use TouchLockPro, to suspend the device, so you do not need the power button for that too.
Also you can set the phone to awake on pressing any key (Windows Mobile Setting), but be sure to have a good locking tool, which makes sure you do not have bogus calls and it goes to sleep again fast enough, otherwise it will drain battery.
I have the same problem.
Anyone solved this one?
I have the same issue and this is not a hardware problem. Strange since even updates/changes of the rom do not correct the issue. Did anybody find a solution for this...?
Well.. ive had this problem just ones.. I was walking downtown with my diamond in the frontpocket of my jeans (face down), after about 3min. of walk, it started to rain (big drops), and my clothes got completely wet, i turned around emidietly, to walk back to home. When i got home after 3 more min. i layed the phone on the table, and then i could hear there were somethibg wrong.. The "turn off" sound came, and the notification kept on coming up, even though i pressed No, as if i were just holding the power button down.. Then i began to press the power button continuesly for about a 100 times, and to my surprise then it stopped and have functioned perfectly for about 2 month now.. Something tells me theres some serius promlem with the smallest kind of moisture near the power button on this phone..
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
Hi! on one of my diamond, the power button off from the board. So the black little board with the button itself is not part of the complete circuit anymore... if someone know the hw testpoint for that it would great please.... i see a few TP around, but if i just start sorting them i just going to kill it...I use to flash phones with TP so is not new for me , but i find nothing for diamond.
I have a similar issue. Mine seems like it is almost stuck on, so it wakes its self up all the time, meaning a full charge lasts an hour or two. Then when it runs out of battery it tries to switch itself back on, so goes through a continuous cycle of vibrating and beeping until the battery is removed. The gf finds it very annoying at 3am lol.
Don't recall mine getting wet, but it's possible it could have got damp at some point, but it's been doing this now for about 3 weeks.
Tried a hard reset with no luck.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
2004mark said:
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
Click to expand...
Click to collapse
I think I should send it to HTC, and ask them to do it. Or go to a repair centre. But I should not try it myself, because it can be dangerous for the diamond.
Also try searching on ebay, there might be the parts you could use.
Good luck!
is there a way to remap the power button?
my diamond face same problem since this afternoon, arrrrgghhhh!!!
- blocking hwbutton1, hwbutton2, hwbutton3, hwbutton4, hwbutton5, hwbutton6, hwbutton7 >>>> NO LUCK
- hard reset >>> NO LUCK
guys, any of you solved the problem yet
youtube.com/watch?v=Q4SEQ6AUFOI
My Sony X1 have some strange problems with the power button. When it goes into sleep mode, I can not wake it up with the power button, all I can do is to soft reset. Sometimes it does not go into sleep mode either , it just "wake up" all the time. I don't know what's wrong with it, tried Hard reset but no use .
ANyone had this problems before?
@
The only way to solve this is to leave the phone near your laptop heat vent ( fan) . hot air from it might help you to get the power button up and running. But if that to doesn't work then i'm afraid thats bad.
Current sol :
1. download SU2U ( search threads )
2. go to the settings and make the " lock when stylus inserted" option ON
3. Change the screen turn off time to 5 secs..
So , to unlock , remove stylus , to lock -> insert it back ( its turns off the back light within 5 sec )
Less annoying
elektros said:
youtube.com/watch?v=Q4SEQ6AUFOI
Click to expand...
Click to collapse
thanks for this link, i accidentally tear off my power button flex. now i could turn it on again. Thanks elektros
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
dam1en said:
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
Click to expand...
Click to collapse
Sounds like a hardware issue or simply a bad flash. Have you attempted to reflash the rom? Which rom are you using?
Well...
It wasn't working again this morning, but suddenly - out of nowhere - began to work properly. I'm stumped. If I ever figure out the exact issue I'll be sure to post back.
Thanks
Greetings,
I have same problem on my tytn...
Sometimes it suddenly starts working fine, but shortly it breaks again.
I have tried hard-reseting while it was working, but didnt help.
I think the problem appeared after charging my phone with a motorola v3 charger, so maybe it damaged my phone with over-voltage or something...
Anyway, if someone can suggest something i would be very grateful!
Hi I have exactly the same symptoms with my HTC Tytn II...when you power it on it starts typing letters (in my case CEDF). If the recording button is active it will start recording too. This happened suddenly and I haven't used any other charging apart from the usb and wall socket charger supplied with it.
All buttons (except front center key) and keyboard do not work. Any suggestions would be appreciated very much. This phone is only 8 months old.
Hi,
my Kaiser with dutty's WM6.1WWE ROM did the same this morning Yes I disabled the button 6 and stopped the voice recordings but all the hardware keys but few in the center of the keyboard are not responding. So I cant make or receive calls without taking the stylus out and touching the screen soft buttons andd that's pin in the ... while I am driving. I am using this ROM for almost a year now and I am extremely hapy (up to now) with its performance. When it all happened there were no activities on the phone - I woke up from a SMS notification (Yes I did receive an SMS from my bank) followed by repeting Voice Recordings. Any help will be highly appresiated! Thanks in advance!
keyboard problem
I am experiencing a similar problem with my stock tilt my keyboard does work however none of the text appears on the screen. I have tried hard reset and everything else I could think of, short of a clear storage reload. I would appreciate any help or suggestions from some of you more experienced users.
Bisonwill
anyone ever figure this problem out? im having the same thing happen now.
Same here
I've had it for a couple of weeks now.
I'm running WM6.1 from HTC (rom ver.3.29.422.1 from 2009-01-12) so nothing fancy here.
I even ordered and replaced the D-Pad and I replaced the keyboard (just the sticky part though). I totaly dismantled the phone and didn't find any issues with the cables.
Any ideas would be highly appreciated
Join the club!
This is crazy. My problem is exactly the same. I re-romed to the latest phoenix and it did not change a thing.
Help!
help....
any body here found a solution for the keypad/keyboard yet??? i have the same problem as you guys... any idea, thanks so much...
i have the same problem And there is something else. My Kaiser wakes up every 2 minutes - it's killing the battery. It works only for 6 hours now
Help
bump!!!
No more people with this issue or any solutions?
Pls! Help
ive joined the gang!
I decided to flash my cooked rom ive been working on.
i hadnt changed much in the kitchen and i think the flash has went badly.
it starts booting windows and where it should state "calibrate screen" it goes white and hangs there, buttons seem to respond by lighting up when pressed.
Now when i try to get it into bootloader or even hard reset it just doesnt work.
it just restarts the phone.
before this happened the backspace key hasnt been working for ages.
anybody got any ideas??
(lucky for me i have a backup kaiser!)
I'm having the same problem. Automatic wakeup, applications starting automatically, can't use keyboard, have to to use screen to use phone etc. I've hardreset using the clear storage method, reflashed a couple of times, but nothing helped. So here I am joining the club
If it's not a hardware issue, then try to flash another radio, many of the custom ROMs here doesn't include a radio, so if it's caused by a wrong radio, flash a new ROM without a radio doesn't help.
Check the Sticky for 'how to' if not aware.
PS: Check here for something need to know..
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Danhargreaves said:
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Click to expand...
Click to collapse
Try this:
1. Take out the battery from the phone.
2. Take out SIM card and SD card.
3. Press in and hold the CAMERA button.
4. Plugin to your computer using the USB cable, while keep holding press in the CAMERA button.
See does it enter the BOOTLOADER mode.
Once entered the BOOTLOADER mode, you can flash a new radio or rom right from there, in your regular way of running KaiserCustomRUU.exe.(Since you already have a HardSPL flashed on, otherwise a HardSPL is needed to flash first.)
Good luck.
Edit: If the power button and the camera button is still working, you can use the regular way of entering BOOTLOADER mode, and flash from bootloader mode or flash from SD card.
Originally posted by Manpreet @ www.sakajati.com
To enter in bootloader mode:
Simply Switch off your phone. Press and hold camera button and also press and hold the power button..You can remove ur finger from power button when phone is switched on but keep holding camera button until u come to bootloader …Now attach the usb to ur computer and do the flashing you normally do.
Click to expand...
Click to collapse
Thx for your suggestion:
I tried removing battery as sim and sd were already removed due to previous attempts in fixing!
so:
i removed battery (did not put back in), plugged in while holding camera
got nothing, so held power button at same time, the green light came on, then went off, and came back on again. but no bootloader.
i tried same procedure with battery in, and all i get is the OS loading up, no bootloader no matter how long i hold the buttons.
is there any other alternative method to get into bootloader (possibly involving other button presses)?
or any other ideas.
Really want to fix this as it was my "experimental" phone for cooking roms with.
Thanks again.
Suspect you have some hardware issue with the camera button. Can you ever take a photo with it?
Edit: Did you read through every post onthis thread:
MTTY (How to fix a bad ROM flash!)
If you tried that and still no luck, you can post your questions there. There are masters will keep an eye on that thread. And generally they only have time to look into their 'subscribed' threads, chances are they will not look into here.
Edit: Maybe the procedure I told is wrong, since I call from memory, check this:
dwny said:
If you have a bad flash....that's no reason to worry.
I haven't had to use MTTY to recover.
In most cases, if there's no issues with the Rom itself...you can pop out the battery and re-flash the same ROM from BootLoader Mode. This will also work if for some reason your computer crashes or loses power & restart during the FLASH.
If the Rom has issues.....the flash will not complete and the device will be stuck in BootLoader Mode. At this point,you must FLASH a FACTORY ROM!!
Pop the battery off 1st, power up the device, device will power up in BootLoader Mode, connect to pc & FLASH your devices FACTORY ROM. This will restore your device back to it's original out the box settings.
The above only works if the device has been put through the Hard SPL or SuperCID process.
I personally have never tried to flash a cooked ROM without unlocking any of my devices. From what I've read what others have experienced...the flash would just fail and they're stuck in BootLoader Mode.
Myself ... I've experienced bad flashes, bad cooked roms that I've cooked, lost power to a pc & had my pc crash during a flash. Listed above is how I've recovered. There is life after Bootloader Mode.
The only time you have to worry is if your device does not power up at all
As a public chef...it's your responsibility to set the parameters of your ROM! Meaning, Radio, HardSPL, program conflicts, etc.
You are not ultimately responsible if someone bricks their phone but if they pushed the issue, you could be hit with some form of liabilty because you failed on providing a simple Disclaimer that sets the expectation.
I hope I've been helpful.....
Click to expand...
Click to collapse
Edit again:
And try like:
Plug in USB first, and thenn press & hold Camera, Power button etc.
I remember once I read there is a way to enter bootloader without battery, just can not find the original again.
Hello guy,
After flashing new rom (official release) on my Blackstone, works fine for a month, after start the home screen being black like the phone is off but he was not. I try first hard reset from the button located next to the sim card, splash screen appears after went black again. I did not realized is a problem with the screen and I perform a hard reset (volume up+down & power up) . The phone perform the hard reset because I heard the power up sound, plus for about one minute I have the screen on, asking me to make the screen line up. During the screen line up the screen went black again and no way to see it showing something again. The problem is in active sync the phone is not recognized anymore, I can't flash it again (I try run RUU but give a error message to connect the phone) plus I'm going blind without seeing anything on the screen. My question is there is any way to solve this problem.
Thank you in advance.
Although screen is black, you should still be able to get into bootloader by normal procedure (turn off device, hold vol down & then press power on). Once in bootloader try flashing (you may wanna try returning phone to stock rom as it sounds like your screen has become loose from motherboard and needs fixed under warranty).
To return to stock rom follow guidelines at bottom of first post in this thread.
Still not working
Thank you for the quick reply, I manage to flash it again with the original rom, but nothing happen, the screen is still black. Probably as you said is something wrong with the display. Another problem is I don't have any more warranty; maybe there is a solution to solve the problem?
The Blackstone is out for less than one Year. Your should really have warranty. oO
Yes you wright but I’m 10000 km from home where who knows where the receipt is. Still hopping there is a solution, maybe I can fix it somehow. By the time I get home the waranty is gone. Thanks.
open it up, and attach the ribbon cable back in, just take your time if you need the htc touch hd service manual, i have it. if you wish to use it let me know i will post it here.
That is going to be a big help because I never open up a phone, I watch couple of times some videos on you tube but that’s all about. Anyway I have to open it because I flash it with 3 different roms and still the screen is black. Even when flashing does not showing anything on the screen. I remember for my old blackjack I had a app called My Mobile to see the screen on your desktop I install that I so the splash screen , the align the screen but I couldn’t go more taping the screen of the phone by looking to the desktop.
Thank you for your help and I waiting for the service manual.
Thanks’ one more time.
You can get the service manual here: http://htcdriver.com/index.php?page=htc-blackstone-touch-hd-service-manual
Start downloading. Thank you
Keep us up-to-date on your progress so we can aid & assist if possible
Ta
Rick
Fallen Spartan said:
Keep us up-to-date on your progress so we can aid & assist if possible
Ta
Rick
Click to expand...
Click to collapse
Thank you,
First I have to find a place where I can buy the tools, probably in couple of days I let you know about the evolution of the HTC operation.
You dont have the possibility to contact youre retailer and require a copy of the receipt?
Since the phone got an IMEI number, you could probably just send them the phone and they'll see that you still have warranty on it.
I'd call them before sending the phone, also.. don't forget to restore the spl etc..