Related
Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
The same I thought...but I sold TomTom gps years ago...
inframan said:
Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
Click to expand...
Click to collapse
Great idea. So in theory, any magnetic adhesive strip should serve in the car. Hmmm....
Maybe these
http://cgi.ebay.co.uk/Magnetic-Stri...yZ123866QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Or cheaper ones!
inframan said:
Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
Click to expand...
Click to collapse
This is great! Can't believe I didn't think of it. DUH! Great job on reporting this.
I'm thinking of going to the hardware store and getting a small L shaped metal "plate" and put velcro on the back of it. Should hold things nicely.
Like the way you kept the case on it. I would have done exactly the same thing. Not only does it help but I would be too lazy to remove it all the time when I got into my vehicle.
magnetic adhesive strip
Actually I tried magnetic adhesive strip, but it is quite weak ... Found out a normal metal ruler is better magnetic adhesive, as the keyboard is quite a strong magnet
@topic
Its really a good idea... I might try it...
Im using this one
it's fantastic and very solid
Can anyone recommend a windscreen mount that would meet my following requirements?
1. Must hold the HD2 securely (goes without saying) - but doesn't have to be specifically designed for the HD2
2. Under or around £10 (can't afford those £40-£60 'official' things!)
3. Must not block camera lens as I wish to record some of my journeys
4. Can swivel portrait/landscape without removing
I have found a fair view that 'might' meet these requirements but I'd like to know for sure.
- http://cgi.ebay.co.uk/AIO-PREMIUM-C...ries_MobilePhoneBatteries?hash=item2304e852d0 <--- this looks decent but I can't work out whether it blocks the lens or not??
- http://www.dealextreme.com/details.dx/sku.1154
(some more but I've lost the urls - loads on DX to choose from)
Any help's much appreciated!
Hi, I bought this one on eBay:
WINDSCREEN SUCTION CAR HOLDER & CHARGER FOR HTC HD2 LEO, the company is "e-Cell"
It arrived yesterday and it works the way you want it to - there is a hole for the camera lens, but not for the LEDs, and it swivels all the way round.
It costs £7.85, with free P & P, and includes a cigarette lighter power supply (which I haven't used yet).
I hope this helps.
EDIT: I checked and the item is no longer listed - perhaps they're out of stock.
Thanks John, I managed to find the one you're referring to via Google but as you say it's sold out: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=200433261802
It looks very similar to the ones being sold by DX for other devices (currently none on DX for HD2), e.g.
http://www.dealextreme.com/details.dx/sku.18225
http://www.dealextreme.com/details.dx/sku.22814
It looks decent - how easy is it to put your HD2 into and remove it from the holder?
I've also found this super cheap universal one on DX: http://www.dealextreme.com/details.dx/sku.23565
...which allows full swiveling and most likely the top of the HD2 (camera, flash) would stick out from the holder making it accessible for filming. I may order this one as I can always give it to a friend if it doesn't work out, though I'm def still interested in more stuff like your link.
Cheers
The Capdase Car Mount will work.
Try E-CELL on E-bay. I bought mine there, it is a veryy good holder for the HD2 and cost app. 8 pounds.
Search ebay for this "Holder Mount USB Car Charger For HTC Touch HD2 Leo 100". Has opening for camera and holds phone in landscape which is good for copilot.
Hi,
This is for the e-Cell model:
If you imagine the phone in the landscape position, with the five buttons to the right, the phone slots into two grips left and right, at the bottom. These are fixed and don't move, but at the top, in the centre of the phone holder is another clip that flexes to allow the insertion and removal of the phone. This piece of plastic then clips onto a standard flexible arm windscreen mount, which in turn fixes to the windscreen with a suction cup. There is a ball joint on the back of the phone clip, which, when you've found your best position, can be tightened to lock the mount so that it will not move.
I've only used mine a couple of times and it's relatively easy to put in and remove the phone, perhaps a bit stiff at first, and I've found it easier to fit the phone into the holder first and then attach the complete assembly to the windscreen. It seems to work OK, so it may be worth waiting for e-Cell to get new stock, particularly as you also get a cigarette lighter charger, and it's only £7.85 with free postage.
This looks similar to the e-Cell model:
http://www.mobilefun.co.uk/car-pack-for-the-htc-hd2-p23420.htm but they're sold out too! The joint on this looks more sophisticated, but it's more than twice as expensive. There seems to be a hole for the lens, but the picture isn't very clear.
http://cgi.ebay.it/ws/eBayISAPI.dll?ViewItem&item=280435698894&ssPageName=STRK:MEWNX:IT
mine, cheapest and camera effective, even if I'd prefer a joint-like arm instead of the one it's got
Hi Ephestione,
It's a pity we can't combine the best features of all the mounts. For instance, mine doesn't have the cushioned grips, so I'll have to be careful not to scratch the phone with the rigid clips.
http://cgi.ebay.co.uk/Car-Charger-Mount-Kit-Holder-for-HTC-Touch-HD-2-T8585_W0QQitemZ390175231504QQcmdZViewItemQQptZUK_MobilePhones_MobilePhoneAccessories_MobilePhoneBatteries?hash=item5ad8418e10
this one is available, exacly the same as ecell one, but will come "out of the box", and comes with a charger too. this seller also got the 1600mah andida battery.
for recording purpose, another good point is its having a strong and quite short metal neck that won't take cars vibrations as a long neck/flexible one would. definitely would recomend it.
Hi,
Yes, this is the same as the e-Cell item, and it works well. I paid a bit more because I was impatient and e-Cell seem to be UK based, so delivery was quicker. Some comments I found when I googled the holder questioned the location of the company, but I had no problems. I'll check out the battery, thanks.
I bought this and it will suit ur needs.
Hi there,
the cover for the USB port of my HTC Dream /T-Mobile G1 became loose. The little plastic cable that holds it to the phone ripped but I still had it - I planned to glue the cover back to that plastic cable thing.
Unfortunately I lost that cover now. I was searching the web (including ebay) for replacement but even if I bought a complete housing they'd come without that little plastic cable holding the USB cover.
Does anybody know where to get replacement? By the way I would like to know where to get good (high quality) tools for opening the housing without breaking it.
I appreciate your help.
You would probably have to buy a broken phone and hope that the cover is still intact. While I managed to maintain that cover on mine, I did find it highly frustrating. Many people actually PREFERRED to rip it off. I certainly wouldn't go out of my way to replace it, since that cover really is quite redundant. You won't hurt anything by not having it.
Yes, you're right somehow, it is redundant. It looks a little ugly, though. Maybe someone can still point a way to that cover
2 bricked G1's for sale on ebay for parts:
http://cgi.ebay.com/2-BRICKED-G1-PH...652?pt=LH_DefaultDomain_0&hash=item20b72aa884
Thank's for the ebay link. I am already bidding on some broken phones on ebay.de. though. I though was hoping to find that cover as a sparepart somewhere.
jdb78 said:
Thank's for the ebay link. I am already bidding on some broken phones on ebay.de. though. I though was hoping to find that cover as a sparepart somewhere.
Click to expand...
Click to collapse
Try topicovers.com if you are still having problems. I bought some and now is a big fan of them. Good luck!
What kind of function does the Droid 3's internal coax cable have? Does it work as a wi-fi-antenna, GPS-antenna or both?
I'm going to replace a few parts in my phone, but it looks like I can't do it without breaking the coax cable...just wondering if I can manage a few days without it till I get a new one..
Not sure which cable you are referring, but you should be able to take the whole thing apart without breaking any cables. If it is the one that attaches to the backplate of the phone, you have to lift up on the connector on the phone.
Pictures and more details of what you are trying to do may be helpfull to answering your question
It's the one attached to the backplate. And the backplate is one of parts I'm going to change, but the new backplate replacement does note come with a coax cable. The cable on the old backplate is impossible to remove without breaking it as it's glued to the backplate. Disconnecting the connector is not a problem.
I understand now, I looked at a spare backplate I have and the cable is soldered to the phone in several spots, that would indeed be very hard to remove, but possible with a good iron. I hate how a lot of the replacement parts out there come without important pieces, this is usually a good headache.
If you have the part in hand, it is a simple swap, try it out and see what antennas don't work by trying to connect to gps, wifi etc. If you don't have the part in hand, I would look elsewhere to obtain one.
hey everyone ,
i have a very curious question , why many and many aren't cover the magnetic pins and let it exposed , it's rare to find a cover that covers this area as well
so why is that ? is it because it will weaken the magnetic or something or just a random no reason for that ?
thanks in advance
I've wondered the same thing. Since the Mods require physical connection to the pins, and a case will add thickness to the back, preventing them from touching, it makes no sense to me for the pins to be exposed. Especially when they run the risk of being damaged.
But then, why do so many iPhone cases have a cutout for the Apple? Probably just to show off.
klamation said:
I've wondered the same thing. Since the Mods require physical connection to the pins, and a case will add thickness to the back, preventing them from touching, it makes no sense to me for the pins to be exposed. Especially when they run the risk of being damaged.
But then, why do so many iPhone cases have a cutout for the Apple? Probably just to show off.
Click to expand...
Click to collapse
If it was to Show off with pins this will be weird ???
I would assume they did it solely because they didn't want to cover any connection and not because they understood that it would be better if they covered it to protect the mods. Probably got a specification and just did something similar to what they do with other devices and leave connectors uncovered.
I think this is probably the correct answer. Pretty much all cases available at launch were like this. I'm sure Lenovo just sent out a CAD file to manufacturers but didn't want to give away how Mods actually work, so case designers just generated a cut-out in their CAD file like they usually do without putting any additional thought to it (or thought about it hard, but had to have a product ready for distribution and couldn't afford to hold it back for an explanation).
I've heard somewhere that it was for the pins to release their heat after using a mod for a long period.
Maybe some manufacturer or even Lenovo would make a passthrough adapter for Moto mods,hence the pins are left uncovered.
Then again not likely as thickness and clearance would still be a problem as most cases and covers aren't uniform.Would still be cool though
My two cents here.
Seems like if they cover them and some foreign material got behind the case and the pins, it could short out the pins and potentially cause all kinds of issues. Worst being melting the case or starting a fire. That's my guess