My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.
Related
I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?
Hey,
Just looking for some advice where I should go for a cheap solution on how to fix my phone. Basically, everything still works great! Apart from the big crack, the screen doesn't seem to have been damaged (eg. All the pixels look fine, touch still works, only glass/plastic panel is cracked)
I'm actually really impressed by how it took such a hard hit and the device works fine, the screen didn't even smash! Basically it nudged in between my car seat where you close the door, didn't realise it fell out my pocket and closed the door (you could imagine it would be a hard hit) and the phone lives.
If I just needed the glass replaced, can it be done DIY? Or should I not bother and give it to a service centre? I got it from 3 but I know they'll probably overcharge me for something like this..
Any suggestions welcome, thanks!
if the damage is only to the exterior screen then you may want to consider getting this:
http://www.mobilefun.co.uk/product/17042.htm
be carful! the screen from my firlfreidns diamond is broken too and I had ordered one of those touchscreens... but the screen which comes has no "window" for the frontcamera and after disassembling the phone I saw that it is NOT POSSIBLE to remove the touchscreenglas from the frame.
Replacement LCD & Digitiser
I recently replaced an lcd and digitiser on a HTC Touch Diamond. I bought the complete screen (lcd & digitiser) as one pre-assembled unit from a guy on Ebay (£34.99). Fits straight into the front of the unit frame. I don't think you can remove just the digitiser because it is stuck onto the LCD, and the LCD itself is very fragile. Disassembly is fairly straight forward if you've got the right tools.
Thanks for all your help guys! I've just been bogged down with work so havn't been able to get back here for awhile.
I've taken some time to look into the webiste and others, decided to just order it off ebay in the end anyways. However, taking note from the previous 2 posts, would I be wasting my time ordering just the digitiser itself? I would assume that's what HerrVorragend also meant by "that it is NOT POSSIBLE to remove the touchscreenglas from the frame."
If so, why do they bother selling them online separately? I guess I won't really find an answer, just seems stupid to me. Anyways, guess I'm stuck purchasing both LCD + Digitiser but as a final question, does anyone have any guidelines as how I should replace this myself? I'm very paranoid about this sort of thing because it's only 1 month old, however, I have also replaced an LCD on my old Nokia 6280 before using a step-by-step picture guide online.
Don't think I'd have much luck finding one for this model, hey.. haha.
Once again, thanks!
Double posted, sorry.
badtzmaru56 said:
If so, why do they bother selling them online separately? I guess I won't really find an answer, just seems stupid to me. Anyways, guess I'm stuck purchasing both LCD + Digitiser but as a final question, does anyone have any guidelines as how I should replace this myself? I'm very paranoid about this sort of thing because it's only 1 month old, however, I have also replaced an LCD on my old Nokia 6280 before using a step-by-step picture guide online.
Don't think I'd have much luck finding one for this model, hey.. haha.
Once again, thanks!
Click to expand...
Click to collapse
If you google for HTC Diamond Service Manual, that will help greatly with assembly and disassembly - there are also a couple of videos on Youtube. From my experience the most tricky part is re-connecting the two flex connectors when you re-install the main board. I use the back of a pair of tweezers to slide underneath the connector carefully. If you are nervous about doing it and happy to cover postage costs, I can replace the LCD for you - PM me for details and I'll see what i can do.
Andy
Hi,
Last night I knocked a small table and my girlfriends phone and a remote for the TV fell off.
We noticed that her phone now has a ring of black dots on the screen, mostly visible with a white background (E.G websites) but also from the home screen and the like.
We think she's cancelled her phone insurance, as she's never had a payment out to the company.
Can anyone tell me if its a Digitizer (What is one of these? Is it just the touch screen sensitive part of the phone?) Or the actual LCD Screen itself?
If you click on the photo it will load a larger image
Thanks for any assistance, kinda annoyed about this and wondering if I can repair myself with the parts on ebay. Or does anyone know how much HTC Charge to repair similar? Either in $USD, £GBP or €Eur, I can convert and get a ball park figure.
Hi
First of all is the phone still in warranty? If so take it back to an HTC dealer they should repair it for you for free. TD2 screens are not very good and it's a common fault. ( i had to have mine repaired after just only 3 weeks! )
The TD2 screen is made out of 2 parts, The touch screen or the 'digitizer' as you call it and a normal LCD screen underneath. You need to establish which has gone faulty.
If the touch screen still operates normally i.e the screen does not lock up or freeze and allows you to navigate normally then its the lcd screen below. If the touch screen is faulty one good way of checking is to put a piece of tape over the damaged area and try to lift it up a little to see if the marks / dots disappear and functionality can temporarily be restored.
Its hard to tell from your picture which it is..... sorry
I'm not sure how much a replacement by a dealer would cost, but i'm sure you can replace either yourself. ebay is a good place to look
Hope this helps.
I've had a reply from HTC UK who said the following:
That looks like there are a bunch of very small cracks in the screen. the black stuff is likely the Liquid Crystal from inside the display that has leaked out. If the dots get larger then it would definitely seem that the screen has got some cracks in it.
if this is the case, the standard charge for replacing the LCD is around £180 as sadly it is all one complete unit on the diamond 2, so it is not just the LCD underneath that needs to be replaced, but the whole screen assembly including the touchscreen layer and the actual LCD.
I hope this information helps you to make up your mind.
best regards,
Pete W
HTC
Click to expand...
Click to collapse
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Hi mate,
had the same problem...
the item you psetd from ebay is not the one you need to change.
you need a digitizer, not an lcd screen.
i got one from ebay (http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItemVersion&item=290376721935&view=all&tid=393718237019), it includes both the lcd and the digitizer, you can check ebay to find other auctions offering the digitizer only.
you can change the digitizer on your own if you don't mind loosing the waranty of your phone.
cheers
Hi,
I had already found this: http://cgi.ebay.co.uk/Touch-Screen-...UK_Mobiles_Accessories_RL?hash=item5882e7ef74
Will buy in a bit, funds are a bit short today.
The Touch Screen's functionality hasn't changed at all though, no sticking buttons or anything. So I suspect that its the LCD Screen thats damaged but will follow you're advise as you're going to have more experiance than me (and its the cheaper part to begin with!)
Scrap the above post.. my g/f has just told me that the dots on her phone are bigger/worse. Looks like its the LCD Screen afterall
i still believe it is not the LCD.
the digitizer is actually sitted on a glass, and the LCD is below that. it is very difficult to harm the LCD. i also though it was the LCD (at least i wasn't sure which was broken) so i ordered both of them.
if you disasseble the phone you will be sure if it is the LCD or not.
i vote for the digitizer
good luck, if you need any help, i'll be pleased to help you..
Just to update, A few days after I posted and got helpful advice on here.. she called me up to say the dots have disappeared, and they have still gone now a few days after.
She said she put it in the office where she works, under a printer paper tray, and the office was warm. Something has (maybe only temporarily) fixed it.
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Well F**K me! just bought a second hand diamond 2 to replace my xperia...
...seemed to work great checking it out... went home with the phone in my pocket... and as soon as I turn it on the touch screen doesn't work
dissected the whole phone only to discover the digitizer is glued to the bezel!
I ordered this from Ebay, will update if I got it working with the brand new housing + digitizer: http://cgi.ebay.it/ws/eBayISAPI.dll?ViewItem&item=380166349182&ssPageName=STRK:MEWNX:IT
fingeres crossed
Please report back here on this thread if it works
fluke said:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Can any one help with this matter?
fluke said:
Can any one help with this matter?
Click to expand...
Click to collapse
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
jodeltje said:
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
Click to expand...
Click to collapse
Thanks for the reply as I said previously:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Also the LCD didn´t had any marks at all, but i´m going to buy the TS+LCD and replaced by parts first the lcd because it´s a lot easier to replace then if the problem persists the TS.
I will post the result later when i get the parts to replace.
Superman_1122 said:
I've had a reply from HTC UK who said the following:
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Click to expand...
Click to collapse
Can anyone confirm the above link as being both Lcd and Digitizer? I'm sure it doesn't mention it in the listing but the picture looks like it's showing both connectors.
Most likely only the LCD that's my conclusion if you look at the sellers store.
But to be sure e-mail the seller and ask.
http://stores.shop.ebay.co.uk/Elect...QQ_sidZ195653022?_nkw=diamond+2&submit=Search
Soooooo, as I've already posted here, My digitizer was busted on the phone I just bought... what I didn't tell was that I ordered a digitizer, then checked if I could remove it easily...came to the conclusion that I couldn't... and ordered a digitizer+housing so I could easily fit it on.
the mail brought me the digitizer today, and while knowing a better solution was on it's way I couldn't resist and try if I could make it work.
Turns out it super easy to seperate the digitizer from the bezel using a hairdryer (softening the glue) and a knife:
Take your phone apart, just the 4 screws, click the plastic center off it. Remove the digitizer cable, the touchscreen cable and the speaker cable.
now you are able to remove the green plate which holds all chips and stuff.
underneath that is the screen, lift it up gently going under it from the gap the removal of volume buttons leaves, put it away safely.
Now remove the speaker, the buttons under the zoom bar, and the power button(don't forget the the power button, and rubbery thingy that falls out of the bottom, the hole needs to be at the bottom when putting it back in).
your phone should be completely empty by now... just the front and the digitize glued together.
make the front of the phone reaaaaaaaaaallllly hot, put the knive between the metal and the digitizer (I started at the part where the zoombar is) and gently push it between the two parts... (from the inside of the phone to the oudside). Now just keep the whole thing above the dryer to keep it warm and slowly slice your way around the phone (no secret wires are there that you can cut through).
I used some random glue I had lying around to glue the front back to the new digitizer... perfect!
so the screen is like new now
ps bought this digitizer: http://cgi.ebay.nl/Touch-Screen-Dig...wItemQQptZPDA_Accessories?hash=item45eed6effc
Thanks for that jodeltje.
It sounds exactly the same as when i replaced the digitizer on an Omnia. Really not as hard as one might imagine. Taking your time and being careful are the most important things.
Hey guys,
I came into same boat last night.
Dropped my T-Mobile MDA Compact V from 2.5ft table, Backwards (Not towards LCD) and now it has black dots on screen. I guess the LCD has pressed backwards by chip sets.
Here is a screenshot.
I think its LCD damaged but I don't have cash to replace nor device warranty.
Do you think the problem solves eventually? Coz once I had dropped sony mobile and it too had same issue but solved after many days.
Hopefully it solves.
BTW; does LCD affixed to Digitizer? by seeing service manual, it doesn't look like it is. And I afraid to get cheap hongkong LCD screens for about 30$ since they won't be true quality display. i.e blueish.
Thanks...
Best Regards
hello CRACING,
sorry about what happened to you...
from the picture i can say that you have a problem with the digitizer...
your LCD is ok.
i tend to have this problem over and over again the last 1,5 years... i replace the digitizer (or the glass on which the digitizer is attached to) every 3-4 months..
yes the ones you get from ebay are not that good quiality, but well it keeps the phone working...
if you need assistance on replacing the digitizer, i can help you, by providing pictures and istructions...
cheers
hi, i have my phone opened, and i dont know how to replace digitizer on my LCD screen which i take from phone
Please Urgently.. Thx. Mike
P.S. Must i open LCD scr.?
I'd advise replacing the whole screen as digitizer is glued to screen, there is guides to how to replace the screen which can be found via search one of them is very easy as just remove the four screws from behind the screen.
Good luck
If your only replacing the digitizer, which isn't easy I have done a few.
You will need to carefully remove old digitizer, I heat up the digitizer where it's glued and remove it, it will come off in pieces (glass).
then clean residue glue off lcd frame.
then glue the new digitzer.
last part is soldering the connector on the digitzer to the connector on the lcd it's not easy, it can be done with solder iron but I use a rework station makes it 100 times easier.
good luck
now it isnt urgently.. on night i closed phone.. but it is strange.. my slide effect is strange.. whn i put phone on table, so UP part (LCD,action buttons) is little moved right than DOWN part.. for ex. i think this slide after closing has opposite direction !BUT ONLY LITTLE (1mm)!
thanks for advice..
and i think this thread can could be good tread for everyone who dont know what to do with LCD. As me
I would also advise to replace the entire screen. They are easily sourced from a well known auction site and most will supply the opening tools and a screen protector.
A simple web search will find the service manual to open your pda. There are tuts for replacing the screen by removing the 4 screws behind the screen and pulling the housing apart to slide the screen out. Bewarned that if you are too forceful you will damage the mic and other parts that are still screwed to the board.
I bought two Xda stellars some time back. Both needed a lil TLC. One a scratched screen the other the housing was badly scuffed. Having repaired a few PDAs, I thought I would ask an independant store to see what they would charge (labour only as i would supply parts). He quoted £20 for each phone, have a look at the service manual see the steps to take it apart and reassemble ask yourself for the sake of £20 is it worth the aggro.
Good luck with your replacement, I hope this helps and any others who encounter similar issues.
is it possible to use a raphael lcd replacement and install it on the kaiser? thus allowing a higher dpi?
seedub said:
is it possible to use a raphael lcd replacement and install it on the kaiser? thus allowing a higher dpi?
Click to expand...
Click to collapse
Simple answer, No !
ok, on kaiser i can use only kaiser LCD? (no vogue,no tytn 1.....)
Correct, the Kaiser motherboard is ONLY compatible with the type of screen it originally came with.
I heard the t-mobile wing digitizer would work on the tilt.
I have not try it, maybe on next one needs new digitizer.
My son has just broke the screen on his tytn2, reading through there seems to be the screen itself and the digitiser behind, if I order both of these, are they a simple fit, someone referred to soldering, I do not want to go down that route................
Just found how to video on you tube, looks fiddly, but I will give it a go.
A few days ago I cracked the glass screen on my Dinc. There wasn't any significant damage aside from the crack, and my LCD screen is working fine, so I ordered a replacement on Amazon thinking I could replace it. I found a screen which reviewers claimed came with the tools necessary to replace the screens, although the product did not advertise it as such. I made the order to find that the replacement did not come with any tools, and now I am stumped. Does anyone know where I can find cheap (and usable) tools to crack open my Dinc? I was hoping to finish this before I return to college in a few weeks and I'd rather not go back with a broken screen.
Thanks in advance!
Not sure what "tools" you're looking for, but there are only a few things you need to take your dinc apart (I just did this with mine):
1. T6 screwdriver to remove 4 screws on the big red cover
2. A small flat-head screwdriver to release block clips around the big red housing and pop it off. (also used to open up the ribbon cable clips)
3. small philips-head screwdriver to remove screws securing the main board and LCD
4. X-acto knife + hairdryer to remove the digitizer (the glass that you cracked)
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Sounds like you cracked the digitizer yet you ordered a new screen?
m52 power! said:
Sounds like you cracked the digitizer yet you ordered a new screen?
Click to expand...
Click to collapse
Although the sentence structure is somewhat ambiguous, it sounds like he bought the correct replacement part, a digitizer.
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
I'll vouch for this, it's the biggest headache to replace JUST the glass.
Since you already got the glass, you can go ahead and order a bezel by itself if you want... make sure you get one that has adhesive on the metal lip on the inside so the dust won't get in there
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
Exactly. I made the mistake of ordering JUST the screen and it was a complete headache. I subsequently ordered the frame/screen combo. Much easier.
Sent from my ADR6300 using XDA App
yeah i replaced mine but now i have trouble with the touch screen not working right. It randomly registers touches on the screen. Hope you don't run in to the same issue.
Glad to hear people are having success replacing these. I have a friend who's cracked his recently and will pass this thread on to him.
I replaced my screen with the digitizer/screen combo bought on amazon for under $20. it's a pain to install, but I found a good video on youtube and used their blowdryer method to make the glue more easy to manage and allow the screen to come off in fewer pieces. Also when you put the little ribbons back into their connectors make sure you get them all the way in - I had 256 color-like graphics for a little bit until I reconnected the screen properly
I've done it multiple times. I'm not clumsy, I just got the phone broken in the first place .
While it would make it easier to get the bezel, it can be done fine with just the digitizer.
They give you all the little plastic tools you need usually.
The last time I did it I used Krazy glue instead of very thin double sided tape.
I can answer any specific questions you have when replacing the digitizer if you want.
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal, but it annoys me a tiny bit that my phone isn't perfect.
Could you record the exact order in which you disassemble it? It might even help you out later
drizzt5;19538891
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal said:
I just replaced my screen tonight with an amazon digitizer kit and my trackball is also recessed. Might just open it back up and jam some leftover adhesive underneath it. I would recommend buying the frame though as it was a bit of a b*tch prying broken glass shards and adhesive from the thing. Would also make the phone look better as well..
Click to expand...
Click to collapse
i dont have a cracked screen but a very banged up bezel and battery cover. i calculated it and everything will cost me a total of $35 to replace. this includes the digitizer, bezel, battery cover and camera lens. cant wait to get this done.
thanks for the info on here.
Order the digitizer WITH the housing shell. I cracked my screen, too, and ordered the digitizer/screen only and ended up damaging my housing shell. The hairdryer trick is bogus and doesn't work very well, so spend the extra $10 to get the housing.
I was going to repare the screen to resell on Ebay, but since I broke the housing, I decided to just sell the actual AMOLED screen for $40. I'll find other parts I can sell, too, such as the motherboard and camera piece. Might actually end up making more money. Ah well.
I don't use Verizon anymore, which is why I ditched the DInc. Will miss it though. I do love HTC Sense. I have a Samsung Exhibit II now.
My first time doing this was with the digitizer only. Biggest mistake of my life! I could've made it work, but I was getting it replaced since it was bricked and superglue oozing out the sides might have raised some eyebrows. Digitizer+frame, void sticker, and 2 weeks later I had a "new" dinc.