About a month ago I got my Kaiser screen replaced as it was broken, now all of a sudden the screen is all whitish and I can hardly ready whats on it!
Is the screen broken again??
I'm fixing to replace the screen in a Kaiser i bought used with a broken screen. From the reading i've done, it sounds like one of the cables to the screen is loose. Trying pressing on the middle of your keyboard and see if anything happens. The big ribbon cable has a connector there.
hmmmm coming to think of it when I pressed the middle of the screen it used to do some funny effect (like when you press your TFT monitor) but now nothing happens!
Is your screen something like this?
jrask said:
Is your screen something like this?
Click to expand...
Click to collapse
last night i was woken up by a text, i looked at my phone and all of a sudden the screen went crazy. Started scrolling up and down (like a bad signal/wrong format ntsc/pal on a tv). Everything got all messed up and lines and dashes all over, kinda like your screen, it started acting wierder when i began applying pressure on the top of the device by the earpiece and d-pad. So i soft-reset the device and it was still doing it while boot up, leading me to believe it wasn't a software issue.
So in my half awake state i just left it on my nightstand. I woke up and its perfectly fine now, even when i press all around the screen.. wierd huh?
I didn't notice anything like you descriped, touch screen and everything else worked like before. Only the colors were like on the picture. Tried hard reseting but didn't help. Phone is still under warranty so sent it to be repaired, i can post what they did when i get it back.
Thanks jrask. Thats exactly how it looks.
I think i have some bad news for you, the screen was damaged and needed to be replaced. I think it was cracked under the frame.
I have searched for solutions for the past 2 days but cant find one, if i missed it or this post is redundant , i apologize in advance.
Now my tilt is driving me crazy. It started last week when The touch screen wasnt working, but i fixed it by doing a couple of soft resets. then all the sudden, everytime i slide my keyboard out, the touch screen would stop responding. this went on for a day, then yesterday, when i tired to use the keyboard, the screen went blank, like the light died or something. but when i put it back on portrait, the screen would light up again.
A few moments later, the touch was responding, tried to use the keypad then the screen went blank..tried soft resets about 5 times and uninstalled all recent added programs (skyfire) ..finally the screen was working but the touch still wasnt working.
So this morning, i had the bright idea to do a hard reset....dumbest idea ever cos now its stuck at the screen where i have to "tap the screen to set up your wm device" and guess what..the touch screen isnt responding
plz i really need help with this. all so , i have a broken tilt.., well lcd screen is cracked...can i try to dismantle both tilts and replace the screens?
Ok, i used Code Factory's Remote screen alignment to bypass the alignment, but if i cant use the touch screen or the keyboard, the phone is pretty much useless for sending any information or making calls..is there a way to fix this?
I have had this same issue with my tilt. I could use the scroller on the left side of the unit to navigate but no touch screen. Both times that this has happened to me I removed the screen protector that I had on and restored a backup that I had on my storage card (I run a backup weekly). This has always fixed my issue. You could try another hard reset, not sure if that will help but do you get any lights on the keyboard when you slide it open? Is your tilt less than a year old because there is a manufacturer's warranty too.
Jim
when i slide the keyboard, i do get lights on the keyboard but not on the screen...it just goes dead..but when i slide it back in, the screen comes to life.
I cant do another hard reset cos i have to input the "1,2,3,4" code.
Also , the phone just got out of the 1yr warranty this month...awesome
I want to buy a replacement screen with a new digitizer but i need to be sure that is the problem.. ive searched for this keyboard problem but still have no answers
Now I'm having the same issue, touch not responding. I first noticed it about two days ago, when I slide the keyboard out, I could type just fine, but when I went to send the message the touch screen wouldnt work, so I'd close the keyboard and it would work. well yesterday it stopped working all together, so i used my d-pad and did a sprite restore and it started working again. But then On my way home i hit the lock button, and it stopped working after that, and I couldn't get it unlocked. I used the inner soft key to hit the first part of unlock, but then I couldnt ever figure which button to hit to get the on screen part of the unlock. So I had no choice but to do a hard reset, and just like highoct now I'm stuck on the stylus setup , and the touch still doesnt respond. does anybody esle have any suggestions ? Thanks in advance.
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Oh yeah, I did manage to do a hard reset again, but now the screen is just white. I can hear the sound of it booting up but it still has a white screen. I tired going to the Bootloader screen ( Camera and power at the same time)...still have the white screen. I believe its a hardware problem but i don't know what it is...any ideas?
Ok now I've done a hard flash, using the same HTC kaiser rom 6.1 and it fixes the problem for a little bit, until the first time I slide out the keyboard , then the screen stops working again, any suggestions ?
iPhone 3G Screen Repair...finally an affordable answer
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Does this look like an apple website? did i say i had an iphone? GET OUT OF HERE!!!
Ninety Four said:
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Click to expand...
Click to collapse
And thats his only post, its spam. jerk him outta here
Tilt Touch Screen
highoct said:
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Click to expand...
Click to collapse
I know this thread is a bit old but was searching d forum for possible solutions cos yesterday i developed the same exact problem on my kaiser for no apparent reason!..flashing it hasnt helped and now im stuck on the wm setup screen..when u say u still have the same tilt with the original problem do you mean that the repair was unsuccessful? have you tried reparing it yourself? Thanks
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
grayfoxmg1 said:
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
Click to expand...
Click to collapse
same thing happened to me 3 days ago. touchscreen has just stopped responding.
it still worked when i slided my keyboard out, but only when it was out. then i realized it won't work at all (!) after soft reset. however, i could make it work again like that when i did the soft reset with the keyboard out. weird.
i tried searching, and decided to make a hard reset, flash a new rom, etc, etc., but no more touchscreen. at all. the device doesn't feel any touch in any case. nothing. i bypassed the beggining tap here with the storage card trick. (i've read it somewhere on the forum).
now i can only use my kaiser with the hw buttons, the keyboard, and that's it. no touch. really weird. please if anyone has any updates, solutions, anything, post. sniff sniff
mine doesn't have anything on the screen unless i slide it out, if i have it closed anymore, it just doesn't work at all.
try this:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
se1988 said:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
Click to expand...
Click to collapse
well, i tried both tips, but they didn't work. i'd like to say a big thanks anyway!
then i grabbed the kaiser service manual and took my device apart into pieces. i reconnected pretty much all the cables and stuff, but still no touchy. any further ideas?
you should try replacing the screen. im happy to say that this screen from this seller on eBay worked for me: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250539984183
look here for dissasembly video: http://www.fonlogix.tv/tiltlow.wmv
(to save it to desktop right click link and "save target as")
thanks for your help, i've just ordered a new screen! phew, i hope it's gonna work
Hi i have had an x1 since august but within a month its been dropped and then it was unable to show the screen, i opened my device to try and fix my problem but messed with nothing whatsoever, when i put everything back together it wouldnt even turn on anymore! all it did was charge and when it was fully charged there was a red light. can anyone help me? please im desperate to fix my phone. My first paycheck was spent on this and i loved it despite the numerous flaws! also i havent charged it in over 2 - 3 months. Also when i opened it the tape that connect the rear and the front is kind of messed up, would that effect anything?
The tape that connects the front and the rear is the cable for the screen, so if it's messed up, you might need to get a replacement.
here is a pic, the red part where its circled is where i think the problem is, it looks ripped off, i did have a hard time opening and putting it back together the first time also.
Sounds like (Or rather, looks like) you're screwed, as far as I can tell, if it's really ripped. Otherwise attempt to clean the contact points with some cleaning alcohol and Q-Tips - something might have made it's way in when you disassembled the unit and blocked the electrical signals.
ill try it, but if that doesnt work, would i be able to replace the flex ribbon? would acteone work?
got this checked out by my friend, he told me its the flex ribbon cable, thanks for the help btw. Does anyone know the cheapest place to get a flex ribbon cable from?
Still would like confirmation if its my flex ribbon cable before i spend 40 bucks on a new one. thanks!
Hi, I am new to this forum. Sorry for posting here but I think I have similar or same problem with my xperia. Few days ago I drooped my xperia and then I could not turn it ON. I opened unit, the flex cable was detached.
After attaching the flex cable. I could turn the unit and it booted normal but no response on touching screen I even tried to align it but it did not respond. I turned off the unit. After trying turning it back ON only back light of the screen turned on (no sony logo, no xperia logo no winmo).
I tried to turn it on few times but same result. Even tried to soft reset and hard reset it but no difference only back light. Is it because of flex cable or because some thing else? I can`t even go in to 3 color screen. Please help. Sorry for my bad eng. Thanks.
Hey dear friends
2 days ago my phone failed to the ground from top my bed and got wrecked
My phone's LCD show nothing except that a black screen with a little light
I think and I hope it's from that cable that connect contacts of LCD to main board I think it called Flat or something else.....
I disassemble it my self and I wanna to show it to a mobile service center tomorrow....
anybody have any idea about this issue?what's the problem?
Before you start considering taking it apart, try plugging into your computer first.
I know it sounds daft, but after I dropped my phone last summer, when I tried to turn it on you could see a slight change in the shade of black, yet nothing would show. (Implying that the screen was still powered in some way, but just didn't display anything)
I'd just tried to plug it in to get the data off it before sending it away after a few days of hoping it would come back on, and the screen came back on!
It might not work for you, but it's worth a shot!
Last Xperia X1 I had for repairs had black LCD after a fall. It buzzed and started up, but LCD remained black - flex needs to be replaced.
enigma1nz said:
Last Xperia X1 I had for repairs had black LCD after a fall. It buzzed and started up, but LCD remained black - flex needs to be replaced.
Click to expand...
Click to collapse
hey dear friends....
YES!!I've disassemble it all and I C that flex connection have disconnected....It's OK NOW...Horayyyyyy and tnx for ur helps
Steve_God said:
Before you start considering taking it apart, try plugging into your computer first.
I know it sounds daft, but after I dropped my phone last summer, when I tried to turn it on you could see a slight change in the shade of black, yet nothing would show. (Implying that the screen was still powered in some way, but just didn't display anything)
I'd just tried to plug it in to get the data off it before sending it away after a few days of hoping it would come back on, and the screen came back on!
It might not work for you, but it's worth a shot!
Click to expand...
Click to collapse
did this problem ever come back?
So my Screen broke and I bought a new one so I could replace it, the touch screen/digitizer didn't break though... at first the colors just started washing and fading untill the screen ended up completely dark, I could still use the touch screen and feel when I would unlock it, after a day the phone would not give me any feed back by vibrating or turning the orange light while charging, so I dismantled it using some tips from these videos:
http://www.youtube.com/watch?v=Hhj8Xs9vAyg
http://www.youtube.com/watch?v=hTRXSMQ-GJY&feature=related
After I put everything back together the phone is giving me feedback again and I can notice its charging because of the orange light, but the screen won't turn on. Does any one know if I might need to do something on the software side? like needing to re install anything? or do you think I just got a bad screen?
Update: I just took it apart again and reconnected the ribbons, its back together and the screen still won't turn on.
You have the AMOLED screen and not the LCD?
Did you compare the #'s on the old and new to see you got the right part?
Cables are the same, they look the same, part # and stickers are different...
What are the part numbers on your new and old screen? I just went through the same thing, but I'm fairly sure I got the wrong screen replacement. Will have to look more into it later tonight.
My screen wont turn on at all. I was so excited to get my N1 back in action as well.