Once I got my T-Mobile Note 2, I searched the interwebs for a case that would protect the phone and make it less slippery. The quest was not an easy one, with barely any cases available, and most being replicas with different names. Additionally, none of the ones I saw offered protection around the corners, something that I find 100% essential on a case.
So after several hours on the general Galaxy Note II Accessories forum and several pages down the Amazon hole through multiple search keywords, I found the perfect case, for the time being. The case is a basic TPU S-line hybrid with an added kickstand. Nothing new or revolutionary, I'm sure, but given the lack of choices as of yet, a good one nonetheless.
The case protects, as commented, all 4 corners, and it protrudes enough that it lets you place the phone face down without suffering any damage on the screen. The kickstand works, though this is also the biggest caveat I've found.
The kickstand is on a hinge, and, to keep the case as thin as possible, the kickstand is embedded into the case. This wouldn't be such a problem, this happens on the Seidio Active, for example. However, the case is so thin that the hinges protrude too much out of the case, causing this to be the main point of contact with the surface when you place the phone on its back. It's irritating because one would hope a case would make the phone less slippery when placed on a surface than the original plastic, but hanging from two small pieces of plastic is not much better. There's always the placing the phone on its kickstand position, and that's fine, but don't think about pushing the phone hard on this position, or you'll cause the hinge to let you shift the phone to the "second" position, and, if pushed further, down to the ground.
The kickstand hasn't broken yet, but leaves uncertainty on how long it'll last. The black part of the case is grippy, specially on its sides, with the semi-see-through material being more slippery (though this is not an inconvenience, really).
All ports are well protected, but not covered, so no worries about echo issues like in other cases.
The kickstand is perfect for watching movies on the beautiful 5.5 inch screen.
The durability of the case is debatable. While I'm sure it'll withstand some falls, its purpose is more of a "now it'll not slip off my hands every time I pull it out of my pocket" than "let's toss this sucker from a 20 ft window"
This case more than serves its purpose, and at $5.98 including S&H (shipping from MN, USA), it should be in everyone's short list of capable though cheap cases.
If your phone is naked awaiting a case that fits your immediate needs, this will suffice. If you're looking for something that protects better, is more elegant, and of a known brand, the Seidio Active with Metal Kickstand is my #1 choice. But meanwhile, until it is released, I'd rather have this $6 case than go "naked".
I'm waiting for Amazon to accept all my images that I uploaded so I can provide you with images.
In the meantime, you can check out my Amazon Review here.
>>> It comes on either Black, Blue, Pink, Purple, White. I think I've also seen red, and I'm sure you can also find it on eBay.
>>> Black one seems to be "Unavailable".
Did it come with that screen protector you have installed?
I ordered one from china might get it next year LOL and also ordered another for a note 1, hopefully is as good as this one, I've had the S-line case on my S3 and even tho it was cheap i loved it.. you keep the slimness of the phone witch is important having a 5.5inch screen on the pant pockets isn't fun, imagine adding 1cm of case might aswell get the iDevice-mini.
thanks for the pics now i know what I got into...
BrokenPixel said:
Did it come with that screen protector you have installed?
I ordered one from china might get it next year LOL and also ordered another for a note 1, hopefully is as good as this one, I've had the S-line case on my S3 and even tho it was cheap i loved it.. you keep the slimness of the phone witch is important having a 5.5inch screen on the pant pockets isn't fun, imagine adding 1cm of case might aswell get the iDevice-mini.
thanks for the pics now i know what I got into...
Click to expand...
Click to collapse
Yeah I tried to do it so that the selling company was located in the US, just so it wouldn't take so long to arrive because I was holding the phone naked and it was slippery as hell.
The screen protector is a SPIGEN SGP Samsung Galaxy Note 2 Screen Protector Clear Steinheil [Ultra Oleophobic] [2-PACK]
Personally, I don't think the protector is the best, but I feel more comfortable about using my phone now. The safer the better. I got a scratch on my S2 with Gorilla Glass, because I figured "oh Gorilla Glass...don't need a protector". I tried to put protector when I first got it, but failed on 3 accounts. It just didn't look good. Wore it for a while till it looked even worse and I just simply removed it. And of course... Sh*t happens.
So this time, I ordered protector same time as case. Except it is fulfilled by Amazon so it took 2 days free shipping. I think the price is high, AND I have 2-3 bubbles that don't go away. Really, they aren't bubbles. They're specks of dust, and the surrounding area does not stick to the screen. I've thought about using the second protector but...uh I don't know.
"But it's Gorilla Glass 2, you don't need protector!" Not gonna fall twice for that. "But it's gonna interfere with the S Pen!" You know what, I think from time to time it does interfere. I've noticed sometimes while drawing that I might lift the pen but it still draws on the screen. Not sure if that's due to the screen protector or not...
Anyway, best of luck. Protect your phone with the first thing you find in the meantime until you get your case!
i see there's a minor bump on the kickstand that prevents the phone from laying perfectly flat on it's back. Is there' a slight wobble to it if you lay it flat and touch one side?
I just got this case in today and Im happy with what I got for the money.
Sent from my SPH-L900 using XDA Premium HD app
well....
Since I got the Note 2 from t mobile on the day of launch, the store was not carrying any cases so I went ahead and ordered a cheap plastic case from ebay and ran to the sprint store where they had ONE SAMSUNG OEM FLIP CASE and purchased as well. As everybody knows, this samsung OEM case DOES NOT PROVIDE SIDE/CORNER protectio and since I HAVE NO GRIP hands, I had to have every kind of protection available so I integrated both covers. Here are some sample pics. I will keep this on until I get my SPIGEN case!!!!
p.s. I know it looks kind of ghetto but at least I am protected!!!
yusssi said:
Since I got the Note 2 from t mobile on the day of launch, the store was not carrying any cases so I went ahead and ordered a cheap plastic case from ebay and ran to the sprint store where they had ONE SAMSUNG OEM FLIP CASE and purchased as well. As everybody knows, this samsung OEM case DOES NOT PROVIDE SIDE/CORNER protectio and since I HAVE NO GRIP hands, I had to have every kind of protection available so I integrated both covers. Here are some sample pics. I will keep this on until I get my SPIGEN case!!!!
p.s. I know it looks kind of ghetto but at least I am protected!!!
Click to expand...
Click to collapse
yeah I tried that with my GS3 it was too ghetto for me lol
Is this TPU case thick? I prefer thick rubber case to protect it more but might consider this since it has a kickstand
....
fatboypup said:
yeah I tried that with my GS3 it was too ghetto for me lol
Click to expand...
Click to collapse
Hahahaha!! I know!!!
one80oneday said:
Is this TPU case thick? I prefer thick rubber case to protect it more but might consider this since it has a kickstand
Click to expand...
Click to collapse
It really is thin. This may not be the best for you, but I'd say just because of the kickstand, it may hold you over until you find a better one. Personally looking forward to Trident Aegis and Seidio Active. There's also Otterbox...
I got the same but the phone won't fit well. If I manage to fit the top, the bottom won't. If I do the opposite the top won't. Did yours had this problem?
Sent from my SPH-L900 using xda app-developers app
jamexman said:
I got the same but the phone won't fit well. If I manage to fit the top, the bottom won't. If I do the opposite the top won't. Did yours had this problem?
Sent from my SPH-L900 using xda app-developers app
Click to expand...
Click to collapse
Sorry, can't help you there. I really had no problem whatsoever putting this one in. I've taken it out about a dozen times, and I've never had issues taking it out or putting it back in. I ordered the Seidio Active case, so this one will be retired soon. But while using it, my only complaint was that the stand was not reliable. That's about it.
You might want to contact the seller and get a replacement. Looks like there's something wrong with yours. Also, make sure that all ports/buttons line up, and that they didn't send you the case for the wrong phone or some such.
Good luck!
This case is "unavailable" on Amazon but there are a million of them on Ebay, in all different colors. I got one in clear because I like to show off my phone, not the case, although I know from my old iPod case that I actually like the look of a clear glass-like edge around the sides.
I just wanted to chime in that if you get the clear version, beware that it *will* stick to the back cover of the phone. It's ugly because you get these big blobs and patches, and I found it immediately unacceptable. The case only cost me $5 so I just tried sanding it down on the inside so it wouldn't stick... which technically worked, but now it's even uglier. Yeah, I ruined it, but I couldn't see using it the way it was before. I was also concerned that over time, it'd stick so hard that I wouldn't be able to get it off. Already, whenever I'd take it off, I'd hear a "crack" as it unstuck from the back cover. I'm actually still using it after the sanding and it works just fine and doesn't stick anymore, but it is ugly.
My advice is to get a solid color version of this case if you get one, and still sand the inside of it so it doesn't stick. (Though make sure it's really opaque if you sand it; if it's clear at all, you'll see sanding marks.)
I really like kickstand cases but I'm thinking now of just getting something that gives me a little better grip on the phone (like a textured back cover) and then either not getting a case at all, or getting another one of these and hoping it doesn't stick to a more matte back cover.
for those who don't like the gloss look, how about:
http://www.ebay.com/itm/130804580625
available in other colours too
Pyr0x64 said:
for those who don't like the gloss look, how about:
http://www.ebay.com/itm/130804580625
available in other colours too
Click to expand...
Click to collapse
U have this one? How is it like? The photo doesn't clarify a lot..
Thx
Sent from my GT-N7100 using xda premium
No, I don't have one sorry.
I just spotted it on ebay last night and thought I would post it here as an alternative for people to consider when I saw the thread earlier
I do have it in my watchlist and may purchase later, but at the moment I'm using a FlyGrip and a plain matt tpu case
The kickstand looks a bit more flush on that one. Does not seem like there is much texture in the TPU for grip though. I will let someone else be the guinea pig, but I am curious to hear about it.
Sent from my Obamaphone using Tapatalk.
Me too, I'm very curious about this case...
Sent from my GT-N7100 using xda premium
They have that one in clear now too.
It looks frosted so it probably just has a matte texture that makes it easier to grip.
I found another clear TPU case similar to the first kickstand one but minus the stand and with all 5-star reviews on Amazon... found the same case on Ebay for cheaper (under 5 bucks) so I'm trying that next. If that one still creates unsightly stickiness, I'll just go for a clear hard plastic case. I've used one of those on my iPod for literally 5 years and they are surprisingly effective and look perfect.
LOL. I ordered the clear one to try out. I am so weak and have no will power.
Sent from my Obamaphone using Tapatalk.
Related
http://shop2.sprint.com/NASApp/onli...ryID=CZS5478Q&topPageNumber=0&subPageNumber=0 im going to try this out tomorrow,had one for the galax.1 and the infuse,slim and good protection and grip,of course i will get screen protectors!!
I bought this case at the Sprint store the day I bought my phone just to have something to protect it in until I figured out what I wanted to do as a long term solution. This case ended up being that long term solution. It is very light and thin yet I feel provides a lot of protection on the corners and sides of the phone as well as protruding higher than the glass front of the phone in case the phone is dropped face first. I like the texture on the back of the case a lot in terms of my ability to hang on and use the phone with one hand. This case is a keeper in my opinion.
Sent from my Samsung Galaxy Note 2 using Tapatalk.
this guy posted some photos of his...looks great...
http://forum.xda-developers.com/showpost.php?p=33404579&postcount=42
I also got this same case on release day, it's good case the design on the back gives it good grip. Like stated before it is keeper. But for me I gonna go with something a bit thinker just so I have a piece of mind. hopefully BG makes a tactic style case like the one for the gs3.
these don't look bad in the glacier color.
http://www.otterbox.com/Samsung-Gal...eries-Case/sam4-galaxy-note-2,default,pd.html
Picked one up from sprint as well and i really like it Offers nice protection, grip, and feel. I also got it to hold me over until i found a case i wanted for long term but may end up keeping it, it all depends on if my flygrip sticks well to that textured back.
Sent from my SPH-L900
Any chance this is available for international customers?
The body glove that is.
I too picked one of these up at a Sprint store. I had to go to an official sprint store, the affiliate store I checked first said there weren't any cases being made yet. I paid $26. I agree with the above comments, it's quite nice, although I'll go with a water resistant (siedo/otterbox) whenever it comes out. I did have to trim the top edge of a couple of my microusb cables, I thought about trimming the case but it's pretty thin there, and I only had to very slightly bevel the plastic of the cable. I've had the same problem with my Nexus 7 so no biggie.
Yeah i just bought one too and this thing is too flimsy for my taste. I got spoiled by the Speck case for my Note 1. But i had to patience. Couldnt keep my phone in a plastic box for 2 weeks.
I would LOVE to have a Speck - the Speck case for my 80G Ipod looks like a tire!
GegeV2 said:
Any chance this is available for international customers?
The body glove that is.
Click to expand...
Click to collapse
Yep, I like this case a lot also but can't find it in France or elsewhere in Europe...
Also, this case isn't super rubbery feeling. If that's what you're looking for then this case isn't for you. Personally, I don't care for silicone cases because they get stuck in my pocket and and too rubbery feeling. This case is a bit more pvc feeling and isn't rubberized. I didn't think I would like it, but it's pretty solid. It's a bit more expensive though.
This looks close to what I am looking for. Is it one piece? Seems like it would just slide out ?
Sent from my SPH-L900 using xda app-developers app
cherylbaker said:
This looks close to what I am looking for. Is it one piece? Seems like it would just slide out ?
Sent from my SPH-L900 using xda app-developers app
Click to expand...
Click to collapse
Yes it's one piece. Goes on like a TPU case does, just wraps around the phone
Sent from my SPH-L900
the only disadvantage is it doesn't have the raised areas over the buttons. that's key on the samsung case. I would much rather have the textured back on this one though. It feels great overall, slim, light, and makes the phone feel solid. I wish there was some compromise between them.
So has anyone found a way to get the body glove outside US? It seems to be perfect for my needs. Slimmer and prettier than the samsung tpu case. I've searched but nobody ships it to Europe. Is Sprint the only store selling it? Do you think the case will become available wider or should I just buy the samsung tpu?
Tonio78370 said:
Yep, I like this case a lot also but can't find it in France or elsewhere in Europe...
Click to expand...
Click to collapse
I like the case too. You can order from sprint.com no matter where you live or order over the phone from them.
My cousin just got the GNII 2 days ago, and he too rapped it with the Bodyglove case. So far he likes the case a lot. For me when I get the GNII on 12/1, I will be going the Otterbox Commuter series case route. I will not take any chances when dropping $299 with a 2 year attachment, lol...
I have one, feels awesome. Just wish it had the covers over the buttons. other than that, no complaints
Hate
I hate the cases with covers over the buttons. Takes away from the feel of the phone and having to press extra hard to get a response from the buttons sucks. I have never had a BG cover that I have ever liked. Seen this one on the Sprint sight when I ordered it and it looked good so I gave it a shot. I have had 6 different TPU cases on other phones and this case is the best I have used. So I don't find it a down fall at all the buttons are not covered. Plenty of grip. Raised areas cover the camera and screen edge perfectly. Get it and you wont be disappointed! :good:
Sebring5 said:
I like the case too. You can order from sprint.com no matter where you live or order over the phone from them.
Click to expand...
Click to collapse
No we can't. Sprint.com doesn't ship outside US. That's the problem.
"Orders cannot be sent to PO boxes or international addresses."
Its an accessories related question and i hope its ok to ask here. I just received my Nexus 7 32GB and loving it! As what i would do usually, I immediately started looking for back cases / covers / pouches for this lovely device and then I tought, does it really need one? The material at the back doesnt look like the one that could easily be scratched. But then I see so many cases around and people using them. Maybe to better protect the device when/if it falls? I dont like folio cases anyway and only buying a back case looks like a waste.
Any suggestions?
Sent from my GT-N7100 using xda premium
It can get scratched. I have mine in a case almost all the time and I found a scratch on mine somehow
While it's not essential, I'd still go with a case, because you just never know what may befall your new shiny tablet. Since a lot of cases on the market appear to be cheap and ugly, buy something that is well built and from quality materials. This may set you back $50 or more, but trust me, it's well worth it. The tablet will just feel better in your hand, more secure, and you won't have to worry about the screen being scratched or it getting dinged on the side.
Ever since I got my Norever leather case I like the way my N7 feels way more than it does without it.
If you're only interested in a "back case" then I would consider the Incipio Feather. Here's my review. The Feather did come with a screen protector, but I'm with the others in this thread and I would just go with a full case to protect the whole thing.
FULL DISCLOSURE: The Feather was provided to me by Incipio for the purpose of review. I do not receive any compensation for my reviews.
Protection required
I would have to agree that i enjoy having my nexus out of a case . I like the feel of the back and for me it would not get scratched as im careful.. But I use it while im out and about all the time.. I have almost dropped it a few times.I think if you drop this device and it hits the edge of bezel The screen will crack.So i recommend having a nice case . For me i have the bobjgear silicone case . It does add bulk and the nice look of the device . But it provices alot of protection.
Happy Nexus Owner
Erica Renee
I am thinking of a simple plain matte black slim tpu case. Let's see if I can find one.
Sent from my Nexus 7 using xda premium
Well, having dropped my N7 twice, I can attest to getting a case for the Nexus lol. Both drops were from at least 3 feet and the first one went down rolling to the sidewalk from my truck in my Treegloo case. The N7 came unscathed but the Treegloo had an indentation that could barely notice. The second fall was in the garage cement floor. This time the fall was straight down back side down and went SPLAT. I freaked!:silly: and immediately took it out and found it turned on fine and the glass was uncracked. So I went inside and put the N7 down but noticed the cover didn't sit flush like it normally did, so I took the N7 out of the case and saw the backing corners were coming undone and I had to press down to re-snap them back into the corners again.
Now the treelgoo has been semi-retired now that I have the Seidio Active case on. It works because I now also use the Kropsson Aero modded universal car mount and using the treegloo wouldn't work in that case.
Simply... Yes
as in the title yes, I have had a couple of small falls and one or two larger ones, and having the stock official ASUS ones may have saved it a lot of times, so getting any that will have some bump protection is a definite go ahead
call it insurance
I like the naked feel of the N7 in my hand. It's just right. The options available are all over the map. Those folding contraptions remind me of the old paper maps that I could never get right. The armored ones look like two handers and you are going to drop test it because it's a job just to handle all that bulk. I'm going with a leather YooMee pouch [correction: they call it a sleeve] for transport purposes and working the N7 raw.
Noticed Otterbox just announced the Defender series for the N7.
I like Otterbox but $70 is too expensive for a plastic case. Hell, you get a hand made leather Noreve case for $72.
xips said:
I like the naked feel of the N7 in my hand. It's just right. The options available are all over the map. Those folding contraptions remind me of the old paper maps that I could never get right. The armored ones look like two handers and you are going to drop test it because it's a job just to handle all that bulk. I'm going with a leather YooMee pouch for transport purposes and working the N7 raw.
Noticed Otterbox just announced the Defender series for the N7.
Click to expand...
Click to collapse
I think this would be good. I am not too worried about dropping it but more want to protect it from scratches. A nice leather pouch is what I need. Thanks! Off to eBay
Sent from my Nexus 7 using xda premium
I only use a case outside of my house, otherwise for reading and such I go caseless. I have carpet everywhere and even with a couple drops it's not damaged. It's pretty solid.
ynrozturk said:
I like Otterbox but $70 is too expensive for a plastic case. Hell, you get a hand made leather Noreve case for $72.
Click to expand...
Click to collapse
You're right about that. I figure once things settle down they'll run in the $50 neighborhood. Still, as much as I love Otterbox, I'm afraid it will add too much bulk and that's entirely too much for a stand.
I've had all sorts of adventures with my nexus 7, and to be honest back plate is as good as new, the silver border however is a different story.
I went with a Cruzerlite TPU case $19 doesn't add any bulk really comes in all colors with cool design on the back (they are the androids)
saw this when browsing cases for my wifes s3. Does anyone know of a case like this for the Note 2 that isn't insanely expensive? Main part is the lip that comes up a decent amount above the screen to protect the screen when the phone hits the floor.
http://www.ebay.com/itm/Blue-Black-...291874?pt=PDA_Accessories&hash=item564f2943e2
robl45 said:
saw this when browsing cases for my wifes s3. Does anyone know of a case like this for the Note 2 that isn't insanely expensive? Main part is the lip that comes up a decent amount above the screen to protect the screen when the phone hits the floor.
http://www.ebay.com/itm/Blue-Black-...291874?pt=PDA_Accessories&hash=item564f2943e2
Click to expand...
Click to collapse
Check these out:
http://www.ebay.es/sch/i.html?_nkw=...+note+2&_osacat=0&_trksid=p3286.c0.m270.l1313
I'm basically looking for the same thing, I'd rather be safe then sorry if it hits the floor face down. Also looking for a cheap price point, hopefully less than 20-25
I found some cases, search Note II hybrid on ebay(stolen from another thread)
here is the link(New member restriction)
http://ww w.ebay.com/sch/i.html?_trksid=m570.l3201&_nkw=note+II+hybrid&_sacat=0
mitchillen said:
I'm basically looking for the same thing, I'd rather be safe then sorry if it hits the floor face down. Also looking for a cheap price point, hopefully less than 20-25
I found some cases, search Note II hybrid on ebay(stolen from another thread)
here is the link(New member restriction)
http://ww w.ebay.com/sch/i.html?_trksid=m570.l3201&_nkw=note+II+hybrid&_sacat=0
Click to expand...
Click to collapse
I feel the same way. I'm nervous about dropping my device. The note 2 was actually a gift from my partner, hehe. So I want to take extra good care of it. I even wanted to buy the Otterbox Defender case which would make it a tank. I had that case for my iPhone 3G and it turned it into a tank / brick. So I'm going to stay away from it.
I did buy the Seidio Active Case for my Note 1, and it was a GREAT case. I loved it! It made it thicker, but it wasn't that bad. So I'd suggest a case like that. I wouldn't the Case Mate pop case either, but it's not out yet. Or I'm waiting for the Speck Pixel HD Case. That will make my day! I loved that case so much on my iPhone 4. Great protection, great design. Great case. Until then, I'm going to keep using the original cases and the cheapo cases.
Anyways, good luck! Share your findings / or review your cases I am kind of a case freak. I love cases! :$
CaseMate Pop is available at at&t stores but it's ridiculously expensive.
Sent from my SGH-T889 using xda premium
jlczl said:
CaseMate Pop is available at at&t stores but it's ridiculously expensive.
Sent from my SGH-T889 using xda premium
Click to expand...
Click to collapse
Yeah.... I'm in Europe No AT&T in Spain.
I think AT&T got an exclusive perhaps? I mean, why else would Case-Mate NOT want to put it up on their website and sell 100 times more across the globe?
Feeling charitable? Only a few clicks!http://forum.xda-developers.com/showthread.php?t=2013416
robl45 said:
saw this when browsing cases for my wifes s3. Does anyone know of a case like this for the Note 2 that isn't insanely expensive? Main part is the lip that comes up a decent amount above the screen to protect the screen when the phone hits the floor.
http://www.ebay.com/itm/Blue-Black-...291874?pt=PDA_Accessories&hash=item564f2943e2
Click to expand...
Click to collapse
This is pretty close and comes with a kickstand. The only thing I do not like is the hard shell is 2 piece and might be a pain to remove once you install it. The softshell just stretch over the hard shell. Looks like an otterbox defender with raise screen lip.
http://www.ebay.com/itm/For-Samsung...408949?pt=PDA_Accessories&hash=item5d369fec75
This one looks pretty good too an easy on and off. I think I will order this one.
http://www.ebay.com/itm/BK-White-Ha...659917?pt=PDA_Accessories&hash=item5aebe43bcd
Okay so I just got this case
http://www.ebay.com/itm/330832732520?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649#rpdId
I will try to post some useful info but I DO NOT have my note 2 yet, it is coming tomorrow.
Here goes to a half-assed review
1) The TOP CORNERS are not protected at all. They are protected by the somewhat thin, soft, flexible material and not protected by at least the outer plastic part like on the bottom and that's a problem. I am guessing corners should be protected the most because that is what causes the screen to crack(unless it faceplants)
2) I am NOT SURE about the how trustworthy the lip is because I NEVER had a case on a smartphone and my samsung vibrant was like an unbreakable brick. From my experience of looking at products through videos,pictures,etc. the lip does not seem like it will bring enough protection for a faceplant.
Unfortunately, I will ask for a refund.
P.S. The shipping part was very fast, the only thing that will make this seller a 6/5 would be if I get a refund
Hope this helps some of you out in your decision
Great I just ordered this case in white and blue yesterday
mitchillen said:
Okay so I just got this case
http://www.ebay.com/itm/330832732520?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649#rpdId
I will try to post some useful info but I DO NOT have my note 2 yet, it is coming tomorrow.
Here goes to a half-assed review
1) The TOP CORNERS are not protected at all. They are protected by the somewhat thin, soft, flexible material and not protected by at least the outer plastic part like on the bottom and that's a problem. I am guessing corners should be protected the most because that is what causes the screen to crack(unless it faceplants)
2) I am NOT SURE about the how trustworthy the lip is because I NEVER had a case on a smartphone and my samsung vibrant was like an unbreakable brick. From my experience of looking at products through videos,pictures,etc. the lip does not seem like it will bring enough protection for a faceplant.
Unfortunately, I will ask for a refund.
P.S. The shipping part was very fast, the only thing that will make this seller a 6/5 would be if I get a refund
Hope this helps some of you out in your decision
Click to expand...
Click to collapse
stay away from the dual layer "mesh" like ones on that link. really CRAP
the other ones the fishbone style ones are actually shockingly nice considering how cheap they are. they are NOT easy to take apart again without breaking (slow careful and once you pop the joint use a thumbtack to pop each successive joint)
but they are surprisingly nice.
you can get a case ology case like the one you posted for the Note II I am still waiting for case ology to get on the ball and make the impact case (with the 2 arcs on the back) that I like and use on all my phones when possible.
I also got a Jelly Tank case from korea. its a one piece hybrid but VERY protective. not "as" protective of the screen as I would like but so far very impressed with it.
I got these because of the good protection on the corners and front:
http://www.amazon.com/s/ref=nb_sb_n...Case+for+Samsung+Galaxy+Note+II+Note+2+N7100+
Got the "Hybrid" case from ebay and it sucks. Inside hard shell is doesn't fit so the phone moves around a creaks. Hard to use the buttons and makes it too think. I think I migh try the Ionic Guardian case next.
http://www.ebay.com/itm/400343071194?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
one80oneday said:
Got the "Hybrid" case from ebay and it sucks. Inside hard shell is doesn't fit so the phone moves around a creaks. Hard to use the buttons and makes it too think. I think I migh try the Ionic Guardian case next.
Click to expand...
Click to collapse
Which one exactly
robl45 said:
Which one exactly
Click to expand...
Click to collapse
http://www.ebay.com/itm/400343071194?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
I got the one with the mesh looking back, it's okay especially for the price
I'm looking for a protective case for my Note 2 that has a grippy/hard rubber feel that doesn't slide around when I lay it down on it's back. I have an Otterbox commuter but the back is hard plastic and slides around a lot if I lay it down unless I flip it over. My wife has an Iphone and her otterbox has a very grippy rubbery feel that is non slip. I wish their Note 2 cases were like that. I'm looking at the Griffin Survivor case and was wondering if anyone has any other recommendations before I try it out? Thanks!
dengood1 said:
I'm looking for a protective case for my Note 2 that has a grippy/hard rubber feel that doesn't slide around when I lay it down on it's back. I have an Otterbox commuter but the back is hard plastic and slides around a lot if I lay it down unless I flip it over. My wife has an Iphone and her otterbox has a very grippy rubbery feel that is non slip. I wish their Note 2 cases were like that. I'm looking at the Griffin Survivor case and was wondering if anyone has any other recommendations before I try it out? Thanks!
Click to expand...
Click to collapse
http://www.amazon.com/Duzign-Sentin...1378141878&sr=8-3&keywords=duzign+case+note+2
This case has been discussed by many on this forum and it has good reviews. It is definitely protective and grippy. You can even tell from the back rubbery design. If you want something slim, with a soft matte feel, i'd get the Six Abundant Case: http://www.amazon.com/DBA-Cases-Abu...=1378141992&sr=8-1&keywords=six+abundant+case
Wow, that first one definitely looks grippy!
Thanks!
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
dengood1 said:
Wow, that first one definitely looks grippy!
Thanks!
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
Click to expand...
Click to collapse
You're very welcome
opasha said:
You're very welcome
Click to expand...
Click to collapse
Do you know if the back is hard plastic or a softer rubber feel on the first one? I need it to stay put on a flat surface as I move around at work. The Commuter slides all over the place, which I cannot have. It will "stick" if I turn it over because of the rubber edges, but I need the phone to be face up/hands free. Thanks again for your suggestions.
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
dengood1 said:
Do you know if the back is hard plastic or a softer rubber feel on the first one? I need it to stay put on a flat surface as I move around at work. The Commuter slides all over the place, which I cannot have. It will "stick" if I turn it over because of the rubber edges, but I need the phone to be face up/hands free. Thanks again for your suggestions.
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
Click to expand...
Click to collapse
From all the reviews and things I have heard about it, it seems to be in the middle. A hard rubber. So it's good for shock absorption. Definitely not a soft rubber because that would wear out very easily. However, from what everyone in the forums have said and from the amazon reviews, it seems like it will stay in place without issue. Also, it's only $10 and from amazon. If you don't like it, you can ship it back the same day for a full refund without any cost to you. Just keep the original box/packaging.
Here's a quote from someone who has it: "The back part of the case (the black exterior) feels more like silicone than plastic which gives it a nice look and grip. I have dropped my phone once on this case and I have to say that this case does a very good job on absorbing impact."
dengood1 said:
Do you know if the back is hard plastic or a softer rubber feel on the first one? I need it to stay put on a flat surface as I move around at work. The Commuter slides all over the place, which I cannot have. It will "stick" if I turn it over because of the rubber edges, but I need the phone to be face up/hands free. Thanks again for your suggestions.
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
Click to expand...
Click to collapse
It's a hard plastic exo with a softer plastic inner. I have this case and it will not hold in place on a hard flat surface. Mine will not even "stick" when placed screen down. The kickstand is about a 4/10 (flimsy, too easily collapsed etc)
Also, the buttons, imo, are junk. Last night, after I started using this case again after owning it for ~6 months (used for 2 weeks), I took a razor blade to the buttons. Couldn't stand them being so difficult to press.
However, the drop protection is definitely up to the same level as the commuter, for being such a cheap case.
I'd say it's worth the price, maybe even less.
Also, I have a similar six abundant case that was free. And although it's very nice, and my most used case, it offers very little protection, and definitely not "grippy" on surfaces.
Wish I had some suggestions. The Griffin Sur. looks grippy. If you search the forum here there are a few people that bought one and commented on the quality. I believe they don't officially support it.. So it's actually a knockoff.
Edit2: forum.xda-developers.com/showthread.php?t=2174889 has info for the knockoff griffin. Enjoy.
Brad.S. said:
It's a hard plastic exo with a softer plastic inner. I have this case and it will not hold in place on a hard flat surface. Mine will not even "stick" when placed screen down. The kickstand is about a 4/10 (flimsy, too easily collapsed etc)
Also, the buttons, imo, are junk. Last night, after I started using this case again after owning it for ~6 months (used for 2 weeks), I took a razor blade to the buttons. Couldn't stand them being so difficult to press.
However, the drop protection is definitely up to the same level as the commuter, for being such a cheap case.
I'd say it's worth the price, maybe even less.
Also, I have a similar six abundant case that was free. And although it's very nice, and my most used case, it offers very little protection, and definitely not "grippy" on surfaces.
Wish I had some suggestions. The Griffin Sur. looks grippy. If you search the forum here there are a few people that bought one and commented on the quality. I believe they don't officially support it.. So it's actually a knockoff.
Edit2: forum.xda-developers.com/showthread.php?t=2174889 has info for the knockoff griffin. Enjoy.
Click to expand...
Click to collapse
Thanks for the input, bro. That's rather unfortunate. I guess other sources don't have the best description then.
Have you looked into the body glove case? That looks pretty nice and there is a lot of discussion recently on it in the Post Your Pics of Your Phone thread. Check it out.
opasha said:
Thanks for the input, bro. That's rather unfortunate. I guess other sources don't have the best description then.
Have you looked into the body glove case? That looks pretty nice and there is a lot of discussion recently on it in the Post Your Pics of Your Phone thread. Check it out.
Click to expand...
Click to collapse
Definitely bro, maybe others will chime in with different opinions about it.
I was actually just revisiting the idea of the body glove refined gel case (been subbed to that thread for forever). I remember it being a very popular case earlier this year. At one point there was an eBay seller with ~50 of them for $8+free shipping. I should have jumped on it then. I'm just afraid that the lower section of the case (shiny area) will end up scratching easily (read: shiny back mercury case).
Still haven't even gotten around to trying the UAG... Even though I designed and 3D printed some custom inserts.
What case are you rockin?
Brad.S. said:
Definitely bro, maybe others will chime in with different opinions about it.
I was actually just revisiting the idea of the body glove refined gel case (been subbed to that thread for forever). I remember it being a very popular case earlier this year. At one point there was an eBay seller with ~50 of them for $8+free shipping. I should have jumped on it then. I'm just afraid that the lower section of the case (shiny area) will end up scratching easily (read: shiny back mercury case).
Still haven't even gotten around to trying the UAG... Even though I designed and 3D printed some custom inserts.
What case are you rockin?
Click to expand...
Click to collapse
3d printing?? Dude that's awesome! I saw on geeky gadgets or theawesomer website ad about a 3d real time laser scanner. It was really impressive. Expensive ($1400 I think) but very cool. Right now I'm using my Six Abundant Case. I rotate between that and my white UAG case. The UAG case is worth it for me. It's not super bulky and protects my phone extremely well. I have large hands so I have no problem gripping and using my phone in one hand with either case on. I do have way too many cases at this point. I even have the casemate tough. Totally forgot to mention that. That definitely has a good feel in terms of grip and it is super slim for a fully protective case. Another nice one is the DBA ultra case. I'll most likely be upgrading to the note 3 so I stopped buying more cases, lol.
opasha said:
3d printing?? Dude that's awesome! I saw on geeky gadgets or theawesomer website ad about a 3d real time laser scanner. It was really impressive. Expensive ($1400 I think) but very cool. Right now I'm using my Six Abundant Case. I rotate between that and my white UAG case. The UAG case is worth it for me. It's not super bulky and protects my phone extremely well. I have large hands so I have no problem gripping and using my phone in one hand with either case on. I do have way too many cases at this point. I even have the casemate tough. Totally forgot to mention that. That definitely has a good feel in terms of grip and it is super slim for a fully protective case. Another nice one is the DBA ultra case. I'll most likely be upgrading to the note 3 so I stopped buying more cases, lol.
Click to expand...
Click to collapse
Yeah! Got into robotics development at my University a few years back and somehow got nominated to be the guy that learns the ins/outs of our 3D printer so that I can teach others everything about it (even the computer science professors). In the printing world, $1400 is fairly cheap for a production item.
I did see the 3D scanner. I believe it is going to be made by Makerbot. We made our own using a Kinect (think: xbox 360) to do real-time scans of objects and roll them into 3D files. However, I usually make one-off prints so I have to build them entirely by hand in a 3D environment.
Agh.. You are making it hard not to press the "complete my order" button for the black uag haha. I too have large hands/long fingers; I often get my iPhone-using-friends asking me how I always use one hand with this beast. If I was a female I'm sure I'd have gained muscle from just using it by now lol.
Forgot about casemate. I'll have to check them out. (have their tough case on my Skyrocket & love it)
I'll most likely be upgrading as well (if not at least a smart watch).. So now seems like a bad time for me to by yet another case.. But.. I have an addiction lol.
Brad.S. said:
Yeah! Got into robotics development at my University a few years back and somehow got nominated to be the guy that learns the ins/outs of our 3D printer so that I can teach others everything about it (even the computer science professors). In the printing world, $1400 is fairly cheap for a production item.
I did see the 3D scanner. I believe it is going to be made by Makerbot. We made our own using a Kinect (think: xbox 360) to do real-time scans of objects and roll them into 3D files. However, I usually make one-off prints so I have to build them entirely by hand in a 3D environment.
Agh.. You are making it hard not to press the "complete my order" button for the black uag haha. I too have large hands/long fingers; I often get my iPhone-using-friends asking me how I always use one hand with this beast. If I was a female I'm sure I'd have gained muscle from just using it by now lol.
Forgot about casemate. I'll have to check them out. (have their tough case on my Skyrocket & love it)
I'll most likely be upgrading as well (if not at least a smart watch).. So now seems like a bad time for me to by yet another case.. But.. I have an addiction lol.
Click to expand...
Click to collapse
That's really nice, bro. I know $1400 is not that expensive when it refers to such technology, but I meant in general - that's like a nice fully loaded laptop price, lol. I'm familiar with Kinect/Xbox360 so yeah, that's really interesting. I'm sure the whole 3D development can take time from scratch. Maybe I missed them, but did you ever post pics of your 3D-rendered cases? I'd love to see how they turned out.
Yes, the Case-Mate Tough is solid. I have the same black one as in this teamvenum review: http://www.teamvenum.com/forum/viewtopic.php?f=9&t=686
I know you complained about the buttons you eventually cut out of your Sentinel case. This is where the UAG shines. The button design makes it super easy to press the covered buttons. The one thing I love about my UAG case is that I can just toss my phone around onto my bed or the table like whatever without any worry. The shock absorption technology on UAG cases is pretty solid. I even got one for my father's S3 and he loves it (esp since he is accident prone/clumsy with all technology, lol).
Yes, the smart watch upgrade is definitely happening for me as well. I can't wait till they release the Samsung Gear this September. It's definitely going to be a step up from my pebble watch, which I use and wear all the time.
Also, your addiction...I understand all too well, especially being a huge tech fanatic. If you don't have a solid protective/easy to hold case currently and work in an environment where you really need that, I would go for it.
opasha said:
That's really nice, bro. I know $1400 is not that expensive when it refers to such technology, but I meant in general - that's like a nice fully loaded laptop price, lol. I'm familiar with Kinect/Xbox360 so yeah, that's really interesting. I'm sure the whole 3D development can take time from scratch. Maybe I missed them, but did you ever post pics of your 3D-rendered cases? I'd love to see how they turned out.
Yes, the Case-Mate Tough is solid. I have the same black one as in this teamvenum review: http://www.teamvenum.com/forum/viewtopic.php?f=9&t=686
I know you complained about the buttons you eventually cut out of your Sentinel case. This is where the UAG shines. The button design makes it super easy to press the covered buttons. The one thing I love about my UAG case is that I can just toss my phone around onto my bed or the table like whatever without any worry. The shock absorption technology on UAG cases is pretty solid. I even got one for my father's S3 and he loves it (esp since he is accident prone/clumsy with all technology, lol).
Yes, the smart watch upgrade is definitely happening for me as well. I can't wait till they release the Samsung Gear this September. It's definitely going to be a step up from my pebble watch, which I use and wear all the time.
Also, your addiction...I understand all too well, especially being a huge tech fanatic. If you don't have a solid protective/easy to hold case currently and work in an environment where you really need that, I would go for it.
Click to expand...
Click to collapse
I never printed any cases for my Note 2, just the inserts for the UAG case with lettering and glow in the dark filament etc. I did make four cases for my gf's S3 but in the end she moved to a pink folio wallet case (which would take too much time to make haha). I've since then had two dead SD cards.. So I've lost a lot of pictures (backups are my priority every 24hrs now..). The cases were more of a "wow factor" type of thing. Everywhere we went people asked more about her case than my huge phone lol.. Lead to a lot of explanations of what a 3D printer is.. But After a few times on/off of the case they'd get weak and start to crack at random layers of which the printer printed it (our printer has a resolution of 0.001mm).
Started sanding the area of the Sentinel case today that I hacked out with the razor to make it smoother. Only had about ten minutes with some 1600grit paper, so I got one side pretty smooth!
I wanted to pledge money to the kreyos smart watch but got worried that I'd be stuck with money in the air for it and no item on my wrist until next summer.. The galaxy gear is definitely going to be watched (pun intended)! As long as it stays within $200-300..
As you can tell, it's hard for me to commit to some purchases lol!
To op: I remember seeing some peel & stick grip strips for phones. They were just thin clear gel-type adhesive strips. Been looking for them but can't find the review. Honestly, I'd also like a grippy case..
Edit: found it! www.egrips.com/ check it out.
Thanks for everyone's input...much appreciated. I own the Bodyglove case but I is still harder plastic than I would like. Its a decent case though. I had the Casemate Toughcase for my Note 1 and liked it, very protective as well, but still had a hard plastic outer shell. Maybe I'll research on getting some type of nonslip rubber strips for my Otterbox to see how that works. There are a few cases mentioned here I'll have to take a look at. Thanks again to you all.
Sent from my SGH-I317 using xda app-developers app
dengood1 said:
Thanks for everyone's input...much appreciated. I own the Bodyglove case but I is still harder plastic than I would like. Its a decent case though. I had the Casemate Toughcase for my Note 1 and liked it, very protective as well, but still had a hard plastic outer shell. Maybe I'll research on getting some type of nonslip rubber strips for my Otterbox to see how that works. There are a few cases mentioned here I'll have to take a look at. Thanks again to you all.
Sent from my SGH-I317 using xda app-developers app
Click to expand...
Click to collapse
Try the DBA Cases Ultra protection cases very good quality and good feel
http://www.dbacases.com/samsung.html
I have the UAG case. I have used the UAG line of cases for all my phones and they are solid. They have the bevel in the front so if it drops face down you wont shatter your screen and it has extra cushion on the corner bumpers. They are only $30 - $35 online. They fit on my OEM samsung dock with spare batttery charger.
The reason why I trust all my phones in the UAG case is that my wife's nephew through my note down the escalator at the mall. My heart stopped as I saw it tumble and bounce off every step. When I went to get it, the phone and case didnt have a scratch on it. The otterboxes are great but they are way too big. Especially for our note.
I am using a cheap eBay tpu. Smoke clear and it is rubber. It works great and protects just fine. Best of all it was only a buck and a half! Rubber does a pretty decent job of keeping it from sliding around unless it is on something very slick. keeps good in the hand too
Sent from my kraken (Note2) using xda app
I have the body glove from sprint.
I feel it offers the best for daily use and it has pocketablility which is nice. It doesn't get hung up as it has a glossy surface at the bottom of the phone.
I don't know if this case has been reviewed yet or not but I just got it today. I had to find a case quick and it needed to be cheap since I don't know if I'll be getting the HTC 10 or LG G5. It also needed to be available for same day Amazon shipping since I couldn't go another day without a case. Don't get me wrong, I would have loved to use this phone without a case but it's design makes it a little difficult for me. My palm is always touching the screen which causes some minor issues but my biggest complaint is while playing a game such as Trials Frontier. When playing a game like this, it starts to become uncomfortable after just 5 minutes of play. It's most likely due to the phones thin edges which are rounded but still sharp when holding it horizontally.
Anyway, this case fixed all of my issues. It still keeps the phone very thing but it provides just enough thickness to the edges to make the phone feel more comfortable when using. The case itself feels well made but I suppose there isn't much to screw up with a TPU case. All of the cutouts match up and the buttons stay very crisp. The case provides a nice grip without providing to much grip to where it becomes an issue sliding your phone in and out of your pockets. The actual fit of the case is very snug but it's still easy to remove. I suppose if you keep on removing it and installing it, there is a possibility it could become loose.
In regards to protection it's not going to work any miracles but I'm sure it would provide some kind of protection during drops. It's a super thin case that has the corners slightly raised. They are raised just enough to keep the display off of a hard surface if the phone falls face down or if you like keeping your phone face down on the table. These raised corners however only slightly sit above the front glass so dropping it on an uneven surface such as asphalt could have dire consequences. The back is no problem at all as the raised corners give the back glass more clearance.
If you're looking for a crystal clear super thin case that offers nice grip, decent protection and allows you to showcase this nice looking phone then you might be interested in it. If you care more about protection than the way your phone looks and feels then this probably isn't the case for you.
You can pick it up on Amazon for $12.99 (PRIME Eligible.)
Side Note: The Edge display keeps full functionality if that's important to you.
Where are all the "Real" pictures?
felloffthetruck said:
Where are all the "Real" pictures?
Click to expand...
Click to collapse
I did this late last night. I'll take some pictures today and add them.
i bought 4 luvvitt cases when they were like $4-5 on slickdeals including this one. haven't opened this one yet, but will. thanks for the review.
Does the back have texture? Does part of the phones glass back stick to it at all?
Also btw the sale on these cases (including the normal clear one) are still going on with the code SLICK007
johnnyz86 said:
Does the back have texture? Does part of the phones glass back stick to it at all?
Also btw the sale on these cases (including the normal clear one) are still going on with the code SLICK007
Click to expand...
Click to collapse
Yes. The back sides are textured. I also just removed it to see if it stuck and no it doesn't.
I don't know what kind of deal that coupon code gets you but it its $10 or less then I'd definitely get one. I needed the case same day shipped through Amazon Prime so I just paid full price.
Sent from my SM-G935T using Tapatalk
Actual pics?
Sent from my SM-G935T using Tapatalk
I also got one as well during the SD promo as well, Posted some pictures of it bellow and sorry if the quality is not up to par.
Just wanted to help out on the real pictures. It's fine I've been using the Spigen Tough Armor for now. Just wanted a clear one for home or if show of how nice the phone looks while still on case.
Thanks from the real pictures. I knew I was forgetting something today. My wife had me running around like a chicken with my head cut off today since we are having family over our house for Easter tomorrow.
Sent from my SM-G935T using Tapatalk
cmart4 said:
i bought 4 luvvitt cases when they were like $4-5 on slickdeals including this one. haven't opened this one yet, but will. thanks for the review.
Click to expand...
Click to collapse
can you detail your opinions about the build and pros cons of the Luvvitt cases.
Bought sleek armor and aside from the lack of lip it seems like a nice low profile case with some protection. Just dont like the fact that the phone when face down with the case does not have enough lip to protect the screen.
The home button rest directly on the surface.Testing this out I caused micro scratches on the home button which is naturally a bit raised.
Would love pics and opinions on what yours are like...