T-Mobile/AT&T with Aussie NON-HLOS on JB Verizon XT907 confirmed - Droid RAZR M Android Development

I still do not know how to get FastBoot_SU working on my XT907 so these things are just experimental.
Verizon XT907 Razr M US with US T-Mobile using NON-HLOS.bin from AUSSIE ICS
I know Edge and Voice is working with my Sim.
No idea how to get FastBoot_SU working so i did this a bit different.
You will need:
VZW_XT907_4.1.1-9.8.1Q-27-2-4_1FF.xml (http://forum.xda-developers.com/showthread.php?t=2017200)
RSDLite6.1.4_FLASH
MotorolaDeviceManager_2.3.4 DRIVERS
NON-HLOS.bin from AUSSIE Razr M it is 102.400KB compared to the US 49.xxxKB (http://dl.dropbox.com/u/8648738/NON-HLOS.bin)
WinRar or any Zip Program
1. Navigate inside VZW_XT907_4.1.1-9.8.1Q-27-2-4_1FF.xml using winrar or winzip and find the original NON-HLOS.Bin over write this with the Aussie Radio 100kb one. Make sure its packed normal again.
2. Use RSDLite, make sure Phone is in Debug mode, flash the new VZW_XT907_4.1.1-9.8.1Q-27-2-4_1FF.xml with the modified Radio.
3. Let the update do its thing, once done insert SIM and enjoy GSM reception.
4. Find a way to gain root access ahhahahaha bc this should wiped ur root access.
There is a way to use FastBoot_SU somehow but it does not work me ...
This is the same modification done to ICS to get it to work with US carriers, except you are on JB or in this case i used JB to flash the entire device.
Some one feel free to clean up these steps or improve this for easy use of tutorial ? You are welcome to edit LOL

followed the steps. but it seems the radio is problematic, because att signal is vey vey weak. I couldnot place call.the same micro sim had 4 bar at my hd2 win phone.
any fix?
Sent from my XT907 using Tapatalk 2

Just tried flashing following your instructions and got stuck.
RSD Lite v5.6 Multi-Flash reports:
Failed flashing process. 16/19 flash "cdrom" -> Phone returned FAIL.; phone connected
Please help!!! Phone now stuck in Fastboot Flash Mode...
Thank you

I did not use 5.6
Also make sure ur battery is above 50% I did have issues flashing when my phone was at about 30-40 ish %
It will show up as low battery.
Get the Stock Verizon JB reflash it with 6.X and up.
Then use a clean version of JB with a modded PJcon Aussie Radio.
And reflash it from there.
To get out of there just Reboot by holding all buttons Power and Volume until reboot.

Thank you!
It only works with version 6 and above.
All is good now.
BTW I just traveled through the documented refarmed areas in Chicago and Cleveland and still no 3g.

yeah same here.
We still figuring out how to get 3G or 4G

Just to add some "fuel to the fire"...a year or so ago I got bored with my Defy and got an Atrix 4G online from the US (I live in Australia). It was AT&T branded and locked so had to purchase an unlock code. When I got it going on Telstra, the reception was just never that good. People always complained they couldn't hear me and I had similar experiences with hearing them. I even gave it to my bro on the other side of the country and he had the same issues.
I suppose what I'm putting forward is that even if it is 2100mhz band or 850mhz band which the Aussie radio does (I don't know what AT&T/T-Mobile run on), it's possibly more than that? I recall reading a VERY interesting article about how much work carriers do to get phones to work on their selected band - no disrespect to any Devs intended, this is just my thoughts as this may be a ghost we're chasing?
Or is the Electrify M XT905 going to work any better?

Works perfectly fine in Germany though Germany uses Stock Rom for XT907
I am getting Super strong signal everywhere better than my iPhone 4, I am using Aussie radio.
I even get better signal than the AT&T users. So it maybe the area, AT&T been getting worse bc they share some towers with T-mobile now.
By that the same tower rent space T-mobile is allowed to put up their Antenna gear, which sometimes decreases signal strength of AT&T.
Which happened alot in my area, alot of AT&T users loosing more signal... and running a modded phone is probably isn't helping the matter.
But T-Mobile seems to have few more frequencies after the refarm ? Maybe that's why ?

The XT907 Definitively is able to get H+ on GSM with Stock Rom in Europe.
H+ we managed to get it to 2.xMB but her normal area we only get 1.5-1.9MB ish
She also picks up E and 3G here and there.
This is on O2 Germany (DE) in Munich Testing to Frankfurt.
Using Stock Verizon Firmware un-modified stock radio.
I will test Aussie Radio next week in Germany see what happens.
But right now She is enjoying H+ with GSM on a XT907.

Hi guys,
I've read the threads in Q/A and this one about different sim cards in RAZR M, and I must say I'm pretty sad because it doesn't work.
I like this phone very much. It's the best phone I've ever seen. But I won't buy it because I don't have money to pay for expensive plans to Verizon (nor I will be in the US for 2 years which is the minimum contract time), and it doesn't work on T mobile which I would like to use. I guess I will have to stay on my Defy and wait for some new unlocked version of Motorola (never gonna happen imo).
Or should I buy it and try this method so I can use it partially with T mobile? Please advise.
Sent from my MB525 using xda app-developers app

I am using it with this method with T-Mobile.
Though when i am in Germany I have to take the mod out to get onto 3G in Germany.
With US-T-mobile we only managed to get Edge Connectivity so far.
I like it because i dont use much data and edge is enough for geting GPS to work smooth and surfing is slooow.
Else all is well =)

Thanks for the info~~~!!

It'd be really cool if the dropbox link worked. Unless im doing something wrong. Unless i can pull it out of another stock/rom file

Great info. Is the dropbox link down for good? I cant seem to find any mirrors :-/

This method has been made obsolete by the discovery of a much simpler procedure that edits a single bit in the radio NVM that enables full service on US carriers.
I wrote up the updated method in the Q&A section.
http://forum.xda-developers.com/showthread.php?t=2166542

Can someone please reupload AUSSIE RADIO as Radiocomm method is not working for me!

Proda said:
Hi guys,
I've read the threads in Q/A and this one about different sim cards in RAZR M, and I must say I'm pretty sad because it doesn't work.
I like this phone very much. It's the best phone I've ever seen. But I won't buy it because I don't have money to pay for expensive plans to Verizon (nor I will be in the US for 2 years which is the minimum contract time), and it doesn't work on T mobile which I would like to use. I guess I will have to stay on my Defy and wait for some new unlocked version of Motorola (never gonna happen imo).
Or should I buy it and try this method so I can use it partially with T mobile? Please advise.
Sent from my MB525 using xda app-developers app
Click to expand...
Click to collapse
May I suggest buying the RAZR i

Germanese said:
I still do not know how to get FastBoot_SU working on my XT907 so these things are just experimental.
Verizon XT907 Razr M US with US T-Mobile using NON-HLOS.bin from AUSSIE ICS
I know Edge and Voice is working with my Sim.
No idea how to get FastBoot_SU working so i did this a bit different.
You will need:
VZW_XT907_4.1.1-9.8.1Q-27-2-4_1FF.xml (http://forum.xda-developers.com/showthread.php?t=2017200)
RSDLite6.1.4_FLASH
MotorolaDeviceManager_2.3.4 DRIVERS
NON-HLOS.bin from AUSSIE Razr M it is 102.400KB compared to the US 49.xxxKB (http://dl.dropbox.com/u/8648738/NON-HLOS.bin)
WinRar or any Zip Program
1. Navigate inside VZW_XT907_4.1.1-9.8.1Q-27-2-4_1FF.xml using winrar or winzip and find the original NON-HLOS.Bin over write this with the Aussie Radio 100kb one. Make sure its packed normal again.
2. Use RSDLite, make sure Phone is in Debug mode, flash the new VZW_XT907_4.1.1-9.8.1Q-27-2-4_1FF.xml with the modified Radio.
3. Let the update do its thing, once done insert SIM and enjoy GSM reception.
4. Find a way to gain root access ahhahahaha bc this should wiped ur root access.
There is a way to use FastBoot_SU somehow but it does not work me ...
This is the same modification done to ICS to get it to work with US carriers, except you are on JB or in this case i used JB to flash the entire device.
Some one feel free to clean up these steps or improve this for easy use of tutorial ? You are welcome to edit LOL
Click to expand...
Click to collapse
is there a way to flash it in a RAZR-M with JB 4.1.2 ?

toroloco73 said:
is there a way to flash it in a RAZR-M with JB 4.1.2 ?
Click to expand...
Click to collapse
Yes it is.
Though I am not sure if it is possible on the 98.18.78.
Earlier ones will work.

Germanese said:
Yes it is.
Though I am not sure if it is possible on the 98.18.78.
Earlier ones will work.
Click to expand...
Click to collapse
now i'm on xt907_stock_deodex_98.16.3
i can't find NON-HLOS.bin from AUSSIE Razr M file

Related

3G Internet Issue

I just saw that early today was added a Fastboot Package for Claro Argentina (Milestone 3 XT860) in this thread: [Fastboot Files] Gingerbread 2.3.5 and 2.3.6 for UMTS XT860 Milestone 3 (Can't link, sorry).
Here is my problem: two weeks ago I was able to access internet from my XT860 using 3G from my house, but since the 24th of December I'm not able to (2G - EDGE works good). I don't know why. If I move two blocks away from my house I have perfect reception and I can use 3G data without any problems. I already took the phone no customer's service and they gave it back to me with another blur version but still it doesn't work. I'm making almost daily calls to Claro but they don't do anything.
Currently I'm using: 2.3.4 with 5.1.790. Should I expect any change if I flash the new files?
Thank you for your help.
P.S: I don't live inside a Faraday cage
Milt75 said:
I just saw that early today was added a Fastboot Package for Claro Argentina (Milestone 3 XT860) in this thread: [Fastboot Files] Gingerbread 2.3.5 and 2.3.6 for UMTS XT860 Milestone 3 (Can't link, sorry).
Here is my problem: two weeks ago I was able to access internet from my XT860 using 3G from my house, but since the 24th of December I'm not able to (2G - EDGE works good). I don't know why. If I move two blocks away from my house I have perfect reception and I can use 3G data without any problems. I already took the phone no customer's service and they gave it back to me with another blur version but still it doesn't work. I'm making almost daily calls to Claro but they don't do anything.
Currently I'm using: 2.3.4 with 5.1.790. Should I expect any change if I flash the new files?
Thank you for your help.
P.S: I don't live inside a Faraday cage
Click to expand...
Click to collapse
That sounds more like a problem with their network. I don't know why your device would selectivly not work just at your house. That's an odd software bug.
Sent from my XT860 using xda premium
Endoroid said:
That sounds more like a problem with their network. I don't know why your device would selectivly not work just at your house. That's an odd software bug.
Click to expand...
Click to collapse
I don't know what's going on but it's weird for me too. Anyway I'm going to flash the new firmware with RSD. First time doing this with Android, any tips?
Milt75 said:
I don't know what's going on but it's weird for me too. Anyway I'm going to flash the new firmware with RSD. First time doing this with Android, any tips?
Click to expand...
Click to collapse
Make sure your battery is fully charged, recently another user borked his phone as it died during flashing. I have a thread called xt860, custom roms and you that has a full guide on fastboot flashing, rooting and custom roms
Sent from my XT860 using xda premium
Well, I've already successfully flashed the new firmware but the problem is still there. That's it, I have no clue on what to do next. Thank you for your support anyway.
Milt75 said:
Well, I've already successfully flashed the new firmware but the problem is still there. That's it, I have no clue on what to do next. Thank you for your support anyway.
Click to expand...
Click to collapse
I think its with their network, or perhaps physical interference from something nearby. I can't think of why it would selectivly not work only at your house if it was a hardware/software issue it would be either all the time or totally random. Try mapping out the area where it cuts in/out and report it to your carrier.
Sent from my XT860 using xda premium
Endoroid said:
I think its with their network, or perhaps physical interference from something nearby. I can't think of why it would selectively not work only at your house if it was a hardware/software issue it would be either all the time or totally random. Try mapping out the area where it cuts in/out and report it to your carrier.
Click to expand...
Click to collapse
I've already reported it. Several times. But they just answer "the computer shows that the antenna is working fine, you shouldn't have any troubles". I call every day to complain about it but they just don't do anything.

[Q]XT860 Radio Image

Is there a XT860 Radio Image or sbf / fastboot file that
will work on gsm (U.S. Bands, I.E. T-Mobile)?
instead of the chinese one, you know!
We have fastboot files from Brazil, Argentina and Mexico. All of these will work on an XT860 and GSM bands. Check out this thread for details and downloads:
http://forum.xda-developers.com/showthread.php?t=1370721
As far as I know, these will not give you H+, only 3G speeds. Currently the only way to have H+ on an XT860 is to be on the Bell Firmware, which we do NOT yet have an SBF for.
Hope that helps.
gbarayah said:
We have fastboot files from Brazil, Argentina and Mexico. All of these will work on an XT860 and GSM bands. Check out this thread for details and downloads:
http://forum.xda-developers.com/showthread.php?t=1370721
As far as I know, these will not give you H+, only 3G speeds. Currently the only way to have H+ on an XT860 is to be on the Bell Firmware, which we do NOT yet have an SBF for.
Hope that helps.
Click to expand...
Click to collapse
i could flash em :/
If you have an xt860 afaik any firmware will work on american gsm though T-Mobile will ply get edge speeds. If you have an xt862 I do not know if xt860 radio.img will work on an xt862. They have different radio hardware
Sent from my XT860 using xda premium
Endoroid said:
If you have an xt860 afaik any firmware will work on american gsm though T-Mobile will ply get edge speeds. If you have an xt862 I do not know if xt860 radio.img will work on an xt862. They have different radio hardware
Sent from my XT860 using xda premium
Click to expand...
Click to collapse
afaik they all have the exact same hardware, idk i have a 62, but i want a better radio, the chinese is INDECIPHERABLE :/, i would like 3g going on tmo which i'm pretty sure possible just not on the chinese radio image, also i can flash the 60's image, i just need a proper(er) img (Hopefully bell's) And a build prop to go with it, i'm making a "Ghetto Fastboot"
ericerk said:
afaik they all have the exact same hardware, idk i have a 62, but i want a better radio, the chinese is INDECIPHERABLE :/, i would like 3g going on tmo which i'm pretty sure possible just not on the chinese radio image, also i can flash the 60's image, i just need a proper(er) img (Hopefully bell's) And a build prop to go with it, i'm making a "Ghetto Fastboot"
Click to expand...
Click to collapse
As far as I know the best you can do with T-Mobile is edge speeds due to them using a band neither device ca use. I wish you the best of luck, if you succeed im sure others would be interested in your results
Sent from my XT860 using xda premium
Endoroid said:
As far as I know the best you can do with T-Mobile is edge speeds due to them using a band neither device ca use. I wish you the best of luck, if you succeed im sure others would be interested in your results
Sent from my XT860 using xda premium
Click to expand...
Click to collapse
Thanks!! we'll see how it goes
T-Mobile uses 1700 MHz for its 3G. These phones do not have compatibility with that frequency. This is what I was trying to tell you before, when I said T-Mobile's 4G is not compatible: it's the same exact network. 3G=4G, only they call it 4G when your phone is capable of greater speeds due to more advanced radio technology, not a different frequency.
T-Mobile only uses 1900 MHz for Edge, and 2100 won't work because it's 4G only, and won't work if you don't also have access to 1700, which is for both 3G and 4G. I hope this makes sense.
I'm glad you made your own thread to deal with this issue, and I hope I am wrong and that someone more knowledgeable comes along and corrects me and tells us all how to make it work. If you figure it out I will apologize as well. However, I just want it to be clear that no one who has made gsm work on the D3 has been able to (let alone interested in) getting 3G/4G to work on T-Mobile. I have assumed it is because it's an incompatibility problem between the hardware of these phones and the network you're trying to use.
Even if you had an xt860, it wouldn't work on 3G on T-Mobile, so using their radio.img and build.prop won't help on the xt862. Just because you can flash them doesn't mean they will work.
By all means, please post results and let me know if I'm wrong. As I said, I would prefer to be wrong in this case, but I don't think I am.
By the way, the xt883 radio.img shouldn't change the functionality of the phone beyond letting it connect to gsm in the US. I really don't see what your gripe is with it. Not that I'm offended or something; who cares. But I use it every day and haven't seen any results worth frowning over, let alone trying to switch to the xt860's which is not at all compatible with CDMA.
BenSWoodruff said:
T-Mobile uses 1700 MHz for its 3G. These phones do not have compatibility with that frequency. This is what I was trying to tell you before, when I said T-Mobile's 4G is not compatible: it's the same exact network. 3G=4G, only they call it 4G when your phone is capable of greater speeds due to more advanced radio technology, not a different frequency.
T-Mobile only uses 1900 MHz for Edge, and 2100 won't work because it's 4G only, and won't work if you don't also have access to 1700, which is for both 3G and 4G. I hope this makes sense.
I'm glad you made your own thread to deal with this issue, and I hope I am wrong and that someone more knowledgeable comes along and corrects me and tells us all how to make it work. If you figure it out I will apologize as well. However, I just want it to be clear that no one who has made gsm work on the D3 has been able to (let alone interested in) getting 3G/4G to work on T-Mobile. I have assumed it is because it's an incompatibility problem between the hardware of these phones and the network you're trying to use.
Even if you had an xt860, it wouldn't work on 3G on T-Mobile, so using their radio.img and build.prop won't help on the xt862. Just because you can flash them doesn't mean they will work.
By all means, please post results and let me know if I'm wrong. As I said, I would prefer to be wrong in this case, but I don't think I am.
By the way, the xt883 radio.img shouldn't change the functionality of the phone beyond letting it connect to gsm in the US. I really don't see what your gripe is with it. Not that I'm offended or something; who cares. But I use it every day and haven't seen any results worth frowning over, let alone trying to switch to the xt860's which is not at all compatible with CDMA.
Click to expand...
Click to collapse
That's how i've understood it, our devices lack the 1700 band. It will work on t-mobile network, but only at edge speeds. I do believe this has been tried. I also don't think an xt860 radio.img will work as expected on an xt862, but i wish him the best of luck. I would like to use t-mobile when i travel to the states, they have a really good pay per day plan compared to others i looked at(although for a week at a time i can live with edge speeds). and yes, xt860 is GSM only if the flash does work there will be no CDMA functionality
bp.img VS radio.img
What is the difference between bp.img and radio.img ?
Is it the same file ?
SX86 said:
What is the difference between bp.img and radio.img ?
Is it the same file ?
Click to expand...
Click to collapse
Open in a Hex Editor to compare. I don't think they are the same... I took apart all of the files in the latest Bell update with no success, as well I tried dd'ing all of the different partition blocks to my phone just before sending it into the shop to get Bell firmware re-loaded onto it and didn't get any luck... in the end it was basically an encrypted bootloader problem.
If we can get the phone bootloader-unlocked we *might* be able to use some of the dd images that were created (I have each partition from bell 2.3.4) flashed through RSD then do the upgrade to the latest Bell, which overwrites the radio and boot partitions...
Let me know if anybody is interested in them. Please note, they the whole partitions and have extra padding on them. Also, I think I missed /preinstall, but I can't remember.
I created a new thread for this... again it's the original Bell stuff 2.3.4. I can probably do the same thing for the current Firmware as well.
Please see http://forum.xda-developers.com/showthread.php?t=1449027 for the 2.3.4 dd images
I've never seen/heard of that first one you mentioned before.
Sent while mobile using Tapatalk.
BenSWoodruff said:
I've never seen/heard of that first one you mentioned before.
Sent while mobile using Tapatalk.
Click to expand...
Click to collapse
its in a candian rom, no its not the same, don't try to flash you'll mess up ur phone
So... did anyone try the XT860 radio on the XT862?

Can this device the 4G one work on tmobile Hugh speed network?

Sent from my SGH-T999 using xda app-developers app
Probably not. T-Mobile's and ATTs 3g bands were different frequencies (1700mhz vs 850/1900). However, in some places T-mobile has started to use 1900mhz and unlocked ATT devices will work. This seems to be random right now and even T-mobile support may not be able to tell you where.
Or you can do what I did, and get nrvate's CM10 build for the i957 (I'm a noob so no links for me yet) then flash this radio: Tmo_SGH-T989_UVLE1_radio.zip (Google it). I get full HSPA+ and have clocked DL speeds up to 19000kbs. Of course YMMV, and no guarantees that it will work for you, won't brick your tab or kill your pets.
cambertoe said:
Probably not. T-Mobile's and ATTs 3g bands were different frequencies (1700mhz vs 850/1900). However, in some places T-mobile has started to use 1900mgz and unlocked ATT devices will work. This seems to be random right now and even T-mobile support may not be able to tell you where.
Or you can do what I did, and get nrvate's CM10 build for the i957 (I'm a noob so no links for me yet) then flash this radio: Tmo_SGH-T989_UVLE1_radio.zip (Google it). I get full HSPA+ and have clocked DL speeds up to 19000kbs. Of course YMMV, and no guarantees that it will work for you, won't brick your tab or kill your pets.
Click to expand...
Click to collapse
WHOA!, are you saying you are getting HSPA+ on TMobile!?
can you PM me a link how to do this. I have my tab rooted, but no roms installed yet. Do you have the links for the roms? What recovery are you using to flash?
Thanks!
BriCo84 said:
WHOA!, are you saying you are getting HSPA+ on TMobile!?
can you PM me a link how to do this. I have my tab rooted, but no roms installed yet. Do you have the links for the roms? What recovery are you using to flash?
Thanks!
Click to expand...
Click to collapse
Yeah it works well with the only problem being the power usage is rather high, and drains faster in idle. After looking at logcat I think this radio doesn't go into idle mode properly so keeps sucking power when not in use. Running it's a little less usage (maybe 30 min less) but on idle it drains in 24 hrs. Turning off 3g helps but for me I can live with this to get 20mb down. When ICS for the i957 finally shows up it should be possible to see a better radio get put in CM10 (which is still in early development, but that's what the ROM below is based on).
I'm using TWRP for recovery. After Clockwork being kind of wonky I have seen the light and use TWRP on all my devices. It just works.
The ROM is here: http://forum.xda-developers.com/showthread.php?t=1867579 and go to post#2. There are some issues but it runs remarkably well for being like 3 weeks old.
This is the radio I used from a Galaxy SII. Google Tmo_SGH-T989_UVLE1_radio.zip and get it from Dev Host. I found out about it looking at radios for similar hardware and found that the Note is close so I took a chace and did it. So far so good!
cambertoe said:
Yeah it works well with the only problem being the power usage is rather high, and drains faster in idle. After looking at logcat I think this radio doesn't go into idle mode properly so keeps sucking power when not in use. Running it's a little less usage (maybe 30 min less) but on idle it drains in 24 hrs. Turning off 3g helps but for me I can live with this to get 20mb down. When ICS for the i957 finally shows up it should be possible to see a better radio get put in CM10 (which is still in early development, but that's what the ROM below is based on).
I'm using TWRP for recovery. After Clockwork being kind of wonky I have seen the light and use TWRP on all my devices. It just works.
The ROM is here: http://forum.xda-developers.com/showthread.php?t=1867579 and go to post#2. There are some issues but it runs remarkably well for being like 3 weeks old.
This is the radio I used from a Galaxy SII. Google Tmo_SGH-T989_UVLE1_radio.zip and get it from Dev Host. I found out about it looking at radios for similar hardware and found that the Note is close so I took a chace and did it. So far so good!
Click to expand...
Click to collapse
This is great to hear. I am going to hold off for now, as I would have to open a TMobile account, and I really dont NEED to have this until I start traveling in a few months.
Now what would be AMAZING, is if somehow this tablet could work on verizon. I have a huge corporate account with them and it would cost me next to nothing to add the tablet to the account, assuming it would work. I didn't think it was possible, but then again, I didn't think TMobile high speed connection was possible either.
Any idea if there is a way to get this working on verizon? Or if anyone is even trying?
BriCo84 said:
Any idea if there is a way to get this working on verizon? Or if anyone is even trying?
Click to expand...
Click to collapse
I can tell you that is impossible. T-Mobile uses GSM and Verizon uses CDMA. You can only put a SIM card device on GSM carriers (TMO and ATT).
cambertoe said:
I can tell you that is impossible. T-Mobile uses GSM and Verizon uses CDMA. You can only put a SIM card device on GSM carriers (TMO and ATT).
Click to expand...
Click to collapse
What about the LTE radios?
Thanks for the reply. Bought one already and hacking it today. Going to do the same thing i did to
Att's note, radio flash!
Sent from my SAMSUNG-SGH-I957 using xda app-developers app
cambertoe said:
Probably not. T-Mobile's and ATTs 3g bands were different frequencies (1700mhz vs 850/1900). However, in some places T-mobile has started to use 1900mgz and unlocked ATT devices will work. This seems to be random right now and even T-mobile support may not be able to tell you where.
Or you can do what I did, and get nrvate's CM10 build for the i957 (I'm a noob so no links for me yet) then flash this radio: Tmo_SGH-T989_UVLE1_radio.zip (Google it). I get full HSPA+ and have clocked DL speeds up to 19000kbs. Of course YMMV, and no guarantees that it will work for you, won't brick your tab or kill your pets.
Click to expand...
Click to collapse
Did you unlock the device, is that necessary?
Sent from my SAMSUNG-SGH-I957 using XDA Premium App
BriCo84 said:
What about the LTE radios?
Click to expand...
Click to collapse
I could not tell you as T-Mobile doesn't have LTE yet. TMO will use a band that the i957 can support, but it will probably take another radio (if any) to work. I've seen 21mb down from HSPA+ so even if I never see LTE I can't be too disappointed
biggie827 said:
Did you unlock the device, is that necessary?
Click to expand...
Click to collapse
Yes it is. The device was locked at ATT and AFAIK there is no other way other than going through a unlock service. I used cell​unlocker.ne​t. $25 and your IMEI gets you a code in a few hours.
cambertoe said:
I could not tell you as T-Mobile doesn't have LTE yet. TMO will use a band that the i957 can support, but it will probably take another radio (if any) to work. I've seen 21mb down from HSPA+ so even if I never see LTE I can't be too disappointed
I am talking about Verizon LTE. Any way of getting it working on Verizon LTE?
Yes it is. The device was locked at ATT and AFAIK there is no other way other than going through a unlock service. I used cell​unlocker.ne​t. $25 and your IMEI gets you a code in a few hours.
Click to expand...
Click to collapse
I can tell you that this is legit. this is what I did. After paying I had the code in minutes and it worked
Sent from my DROID4 using Tapatalk 2
BriCo84 said:
I am talking about Verizon LTE. Any way of getting it working on Verizon LTE?
Click to expand...
Click to collapse
As I said that is impossible because the carriers use incompatible setups. SIM card carriers (GSM) will only work with other SIM card carriers. Verizon uses CDMA with no SIM cards. The networks themselves are completely different and hardware cannot be hacked to work. Most of the world uses GSM with SIM cards and if you travel overseas, you'll need a GSM device to use unlocked devices on any networks. Blame Verizon for picking a standard that 80% of the world doesn't use
Has anyone tried flashing the tmobile high speed radio but on the current rooted stock ICS rom instead of the cm10 rom?
In other words, i have a stock rooted sgh-i957 on samsungs ICS rom and i want to be able to use tmobile high speed network (HSPA+). Does anyone know if thats possible?
Sent from my DROID4 using Tapatalk 2

[Q] What can I do with Developer edit. and...?

Hi all,
I'm waiting patiently for my 64gb developer phone which I should be getting next week. In the meantime I've been combing through the forums trying to get as much information as I can regarding the developer's edition HTC One. When I think I got the answer I'm looking for I see something else that makes me think another way. With this thread I'm hoping to get answers in one place to avoid confusion. Someone please educate me on this phone.
1. Will I be able to get 4G LTE, and or HSPA+?
2. Unlocked bootloader means I can flash roms but not kernels? How will I know which roms/kernels are the correct ones to flash for the dev edition?
3. Has anyone achieved s-off yet and if so which method is the best and easiest?
4. Tmo is going to be my carier. Whats this about Non Tmo devices needing the Tmobile 4GLTE APN added to the phone to connect to 4G LTE? Does this mean I don't have LTE (I guess it related to 1st question). And how do I add the tmo 4gLTE APN?
5. How does insurance work with unlocked phones and who do I get it from?
Sorry for all these questions. I'm fascinated and I want to be a developer one day so I'm trying to find my way. Any help would be greatly appreciated.
saco274 said:
Hi all,
I'm waiting patiently for my 64gb developer phone which I should be getting next week. In the meantime I've been combing through the forums trying to get as much information as I can regarding the developer's edition HTC One. When I think I got the answer I'm looking for I see something else that makes me think another way. With this thread I'm hoping to get answers in one place to avoid confusion. Someone please educate me on this phone.
1. Will I be able to get 4G LTE, and or HSPA+?
2. Unlocked bootloader means I can flash roms but not kernels? How will I know which roms/kernels are the correct ones to flash for the dev edition?
3. Has anyone achieved s-off yet and if so which method is the best and easiest?
4. Tmo is going to be my carier. Whats this about Non Tmo devices needing the Tmobile 4GLTE APN added to the phone to connect to 4G LTE? Does this mean I don't have LTE (I guess it related to 1st question). And how do I add the tmo 4gLTE APN?
5. How does insurance work with unlocked phones and who do I get it from?
Sorry for all these questions. I'm fascinated and I want to be a developer one day so I'm trying to find my way. Any help would be greatly appreciated.
Click to expand...
Click to collapse
1. You can get lte if your in a lte area. You will get hspa if your in a Markey with the 1900 band
2. You can flash roms kernels and radios now with s on
3. Prob no need for s off anymore
4. Put in the SIM should be auto or just Google it
5. Squaretrade.com
Sent from my HTC One using xda premium
I am still struggling, some people say that you will never get 3g, but yes on 4g, some other says that you will never get both of them since you are Tmobile. I can tell you, I have Tmobile wiht my HTC One Dev edition and I am getting HSDPA, and I pretty happy wiht that, but I am also worried why we are not getting 4G, so I also have started reading about that, the specs are almost the same, but it looks like the problem is the radio installed in the dev edition. So it look like if some dev are able to pull the radio out of the Tmobile HTC One version and try to adapt it or maybe directly installed in out dev edition it will work. I heard this a couple of days ago from another topic in this forum.
Good luck:good:
So 4glte runs on AWS 1700 and dev version doesn't support it unless a developer figures out how to flash it on the dev phone. Do you think that possibility is high? Thanks for the info.
Sent from my Evo 4G LTE using Tapatalk 2
Wow... when you say neither that's pretty scary. I certainly hope that's not the case. I live in NJ in a 1900 rich area. I really do hope we can get LTE and hspa+. I told my wife we are getting 4g with these new phones but I guess I read wrong. We're coming from Sprint so even if we get hspa+ it's a major improvement.
Sent from my Evo 4G LTE using Tapatalk 2
saco274 said:
So 4glte runs on AWS 1700 and dev version doesn't support it unless a developer figures out how to flash it on the dev phone. Do you think that possibility is high? Thanks for the info.
Sent from my Evo 4G LTE using Tapatalk 2
Click to expand...
Click to collapse
So I heard that the problem with dev version is that it has the compatibility built in hardware, but the radio which comes with the dev version doesn't support it, the problem here is that I don't know if flashing the radio from Tmobile HTC one will brick our phone.
If some developer could come to the thread and give us some answer, I don't have enough knowledge about how radios works.
flipy34 said:
So I heard that the problem with dev version is that it has the compatibility built in hardware, but the radio which comes with the dev version doesn't support it, the problem here is that I don't know if flashing the radio from Tmobile HTC one will brick our phone.
If some developer could come to the thread and give us some answer, I don't have enough knowledge about how radios works.
Click to expand...
Click to collapse
You can flash it without bricking, but based on a thread in here that it doesn't work. There might be addition files other than the radio or something.
based on this http://forum.xda-developers.com/showthread.php?t=2223236 we have the same devices with T-Mobile and AT&T
http://forum.xda-developers.com/showthread.php?t=2248586 is where some people have tried and it booted, but they don't get HSPA+ on non-refarmed areas.
Tidbits said:
You can flash it without bricking, but based on a thread in here that it doesn't work. There might be addition files other than the radio or something.
based on this http://forum.xda-developers.com/showthread.php?t=2223236 we have the same devices with T-Mobile and AT&T
http://forum.xda-developers.com/showthread.php?t=2248586 is where some people have tried and it booted, but they don't get HSPA+ on non-refarmed areas.
Click to expand...
Click to collapse
I suspect that we are going to need S-Off in order to get this working, assuming that there is not in fact some hardware difference between the dev and TMO versions. I've read the threads, but I don't know where they get their information. I have not seen anything from HTC on which hardware is in the various phones.
stevedebi said:
I suspect that we are going to need S-Off in order to get this working, assuming that there is not in fact some hardware difference between the dev and TMO versions. I've read the threads, but I don't know where they get their information. I have not seen anything from HTC on which hardware is in the various phones.
Click to expand...
Click to collapse
I have not either, but based on current information to go by that's all we have. I think the only way we could tell for sure is a complete tear down of each model, but so far that has not been accomplished. If there are any variations in the hardware we'd see them and could say "It isn't going to work". If there is no difference then it has to be software/firmware thing.

[Q] San Jose, CA: HTC ONE, no LTE at LTE tower and loss of BT audio

Good evening,
I'm an Ericsson(Sprint) tech (Since 2000) in the San Francisco Bay Area.
My phone is unlocked (Via HTC unlock), had TWRP 2.5.0.0 installed, and is running stock other than that. Rooted with SuperSU
I recently got an HTC ONE and found two odd things:
1. After flashing http://forum.xda-developers.com/showthread.php?t=2251788 , and Power Toggles from the Play store, my Bluetooth audio would go away. The call still connects to the BT headset, but no audio. A stock rom re-flash takes care of that issue 100%. Semi-noob lesson learned, back up BEFORE trying new mods.
2. This phone will not connect to 4G LTE. (more detail to come)
I have tried all the obvious choices: Reflash/Reset, make sure CMDA/LTE mode is set, even changed my LTE Next Timer to 5 from 300 in the ##DATA# screen. I even called employee care and verified that my UICC ID is properly set on the account.
Of course, the local store employees have no idea what to tell me.
I exchanged that brand-new HTC ONE for another brand new handset yesterday. It exhibits the very same exact issues.
This morning on the drive to work, it briefly connected to 4G LTE for a speedtest and I haven't seen LTE since.
For those of you who will say "Yes, but you're in a pre-launch market." I hear you. My response to that is that I physically work on the NV sites. I can take a cabinet key and open the cell site up to verify operation. I am testing this standing UNDER or a few feet away from a NV site running 1900mhz LTE, and my company-issued test LTE phone (different model) is picking up LTE no problem. In fact, I'm so close my download speeds are approaching 30mbps.
I've been lurking here for a while but wanted to see what the community thinks. Did I get TWO faulty handsets, or is there something I'm missing? I still have 1.5 weeks to exchange for yet another handset if I need to.
Thanks in advance for your time.
Disclaimer, these are my own opinions, and not those of Ericsson or Sprint in any way.
I'm pretty sure BT audio is a known issue in most custom ROMs.
Look up "Force LTE" in the Sprint forums. See if that changes anything. (You might have already done this, though)
EDIT: Dial *#*#4636#*#* and change it to LTE only and if that works, LTE + CDMA. If that works, try CDMA/EVDO/LTE (default).
BTW: Where is said tower in San Jose? I live there (here?) and I rarely get LTE signals (but I do).
sauprankul said:
Look up "Force LTE" in the Sprint forums. See if that changes anything.
BTW: Where is said tower in San Jose? I live there (here?) and I rarely get LTE signals (but I do).
Click to expand...
Click to collapse
PM Sent. I'll look up Force LTE on the Sprint forums.
sharksfan98 said:
PM Sent. I'll look up Force LTE on the Sprint forums.
Click to expand...
Click to collapse
Forcing LTE only didn't seem to help.
Here's my plan for tomorrow:
1. Drive to official LTE launch market
2. Test for LTE connection with phone as-is
3. If LTE=YES, happy camper
4. If LTE=NO, run the RUU to flash everything back stock (I know I shouldn't need this, but I'm grasping at straws here)
5. Test for LTE after RUU is complete.
6. If LTE=YES, happy camper
7. If LTE=NO, exchange for a black Sprint HTC ONE (Have Silver now). Maybe there's a bad few in a row.
I'll post tomorrow with results.
Also, to be clear, I'm NOT on a custom ROM. I'm on the Stock Sprint ROM, just unlocked and rooted.
I have had better luck with setting my network mode to automatic instead of cdma/lte ... I live In the Fremont area I see tons of areas light up with LTE now ..
But once I get to my house or my shop for work I have nothing lol.
Sent from my HTCONE using xda premium
NORCALkID said:
I have had better luck with setting my network mode to automatic instead of cdma/lte ... I live In the Fremont area I see tons of areas light up with LTE now ..
But once I get to my house or my shop for work I have nothing lol.
Sent from my HTCONE using xda premium
Click to expand...
Click to collapse
There are a lot of people working really hard to get launched. Glad you're seeing some of that paying off.
I've been going into panic mode with my personal HTC One. I had a horrible experience directly with Samsung on my Galaxy SII. I was hoping to just pick this up and see the heavens open and the light shine down lol.
That hasn't been my experience thus far I'm jealous of all of you happy modders going crazy on this beautiful device. I hope to join you soon
sharksfan98 said:
There are a lot of people working really hard to get launched. Glad you're seeing some of that paying off.
I've been going into panic mode with my personal HTC One. I had a horrible experience directly with Samsung on my Galaxy SII. I was hoping to just pick this up and see the heavens open and the light shine down lol.
That hasn't been my experience thus far I'm jealous of all of you happy modders going crazy on this beautiful device. I hope to join you soon
Click to expand...
Click to collapse
You will soon .. I blame most of it on the network. I know you guys are working hard to get it done. I live in union city and and I have been roaming for the past 2 weeks which really sucks ... I have been forced to use roam control and change my prl to have better roaming ... It sucks to say that I am currently roaming on to metro pcs and have great connection both voice and data lolololol
Sent from my HTCONE using xda premium
Well, here's my results:
1. Drive to official LTE launch market DONE
2. Test for LTE connection with phone as-is NO LTE NEXT TO TOWER IN LAUNCHED MARKET
3. If LTE=YES, happy camper NOT A HAPPY CAMPER
4. If LTE=NO, run the RUU to flash everything back stock (I know I shouldn't need this, but I'm grasping at straws here) FLASHED
5. Test for LTE after RUU is complete. NO LTE
6. If LTE=YES, happy camper NOT A HAPPY CAMPER
7. If LTE=NO, exchange for a black Sprint HTC ONE (Have Silver now). Maybe there's a bad few in a row. CALLING TO EXCHANGE NOW
So frustrating. It worked for one connection the morning I got it and then nothing.
Maybe I'll ask for a black ONE just in the hopes that it came from a different production run.
I really want to like this phone, its beautiful. But this will now be my third brand-new handset.
sharksfan98 said:
Well, here's my results:
1. Drive to official LTE launch market DONE
2. Test for LTE connection with phone as-is NO LTE NEXT TO TOWER IN LAUNCHED MARKET
3. If LTE=YES, happy camper NOT A HAPPY CAMPER
4. If LTE=NO, run the RUU to flash everything back stock (I know I shouldn't need this, but I'm grasping at straws here) FLASHED
5. Test for LTE after RUU is complete. NO LTE
6. If LTE=YES, happy camper NOT A HAPPY CAMPER
7. If LTE=NO, exchange for a black Sprint HTC ONE (Have Silver now). Maybe there's a bad few in a row. CALLING TO EXCHANGE NOW
So frustrating. It worked for one connection the morning I got it and then nothing.
Maybe I'll ask for a black ONE just in the hopes that it came from a different production run.
I really want to like this phone, its beautiful. But this will now be my third brand-new handset.
Click to expand...
Click to collapse
Black HTC One all the way! With any luck you just got two lemons. That's pretty awful luck though, and kind of crazy. Maybe you need to sit on top of the tower.
Rirere said:
Black HTC One all the way! With any luck you just got two lemons. That's pretty awful luck though, and kind of crazy. Maybe you need to sit on top of the tower.
Click to expand...
Click to collapse
>Getting my climbing gear out now< LOL
Black ONE is on the way.
Should I just leave the bootloader saying "Re-locked" or go through the dance to get it back to saying "locked?"
I sent the first dud back "Re-locked" as the guys in the store didn't seem to care at all. I guess it's probably no big deal.
I have done very minimal identical items to both phones:
1. Unlock via HTC /Fastboot
2. Install TWRP 2.5 into Recovery via Fastboot
3. Install SuperSU by following the prompts from TWRP 2.5
4. Installed the 3-button mod here: http://forum.xda-developers.com/showthread.php?t=2251788 via TWRP 2.5
5. Installed "Power Toggles" from the Google Play store. (After this step on each phone, Bluetooth would connect, but no audio. I also never saw LTE work again)
6. Reflashed the official RUU after things aren't working.
You guys are all pro modders, is there any step here that would stand out to you as potentially damaging to getting 4G LTE or maybe hurting the radio file somehow? I see everyone having a field day modding and flashing custom ROMs, now I'm scared to do even the basics for fear that somethings going on behind the scenes.
I've got to go do some actual work now. I'll post an update when the Black ONE comes in.
I have had the same problem of LTE not connecting anywhere. I have done the same things as you, including installing power toggles. If I remember correctly, I believe my LTE quit working after installing it as well. I find it hard to believe that the power toggles app could be the culprit, but it's a possibility I guess.
Sent from my HTCONE using xda premium
Hmm...weird. Before and after I rooted my phone and installed TWRP 2.5 with Super SU and left my phone "as-is" I fortunately have always had LTE in the downtown Hayward area.
I've been able to flash custom roms and not really have any issues other than those related to the Rom itself. Hopefully you really did just have bad luck...maybe buy a lottery ticket? Lol.
Good luck with your next One!
Hope it works out for you!
Sent from my HTCONE using xda app-developers app
tristandespain said:
I have had the same problem of LTE not connecting anywhere. I have done the same things as you, including installing power toggles. If I remember correctly, I believe my LTE quit working after installing it as well. I find it hard to believe that the power toggles app could be the culprit, but it's a possibility I guess.
Sent from my HTCONE using xda premium
Click to expand...
Click to collapse
The only thing that doesn't sit right with me is that after I run the RUU to restore everything, you'd think the issue would be fixed right?
Well look at this everyone...does this sound familiar?
From: http://www.howardforums.com/showthr...scuss-All-Related-Questions-Here-ONLY/page509
"UPDATE: awww, one of those 2g/3g toggle widgets permanetly turned off the LTE radio. Yesterday I could see LTE from Tmo, ATT, Cricket, and MetroPCS. Today all LTE options are gone. When I go into *#*#4636#*#* I can re-select LTE/GSM/WCDMA as a preferred network, but when manually searching for network the phone still can't see any LTE. Power cycling the phone, the field goes back to "GSM auto (PRL)", does anyone know how to make the preferred network stick with LTE without changing back in this hidden menu? What should be in this preferred network blank? and how do you make it stick? anyone?"
sharksfan98 said:
The only thing that doesn't sit right with me is that after I run the RUU to restore everything, you'd think the issue would be fixed right?
Click to expand...
Click to collapse
Yeah you would think so. I have ran the RUU on 2 seperate occasions just to make sure and still no LTE. I will probably just end up trying to exchange it for another one and hope the new one holds up better.
Sent from my HTCONE using xda premium
Now we just need one more brave soul to test power toggles to see if it really is a problem. If it is, contact the dev and tell 'em to declare it incompatible with this device!
sauprankul said:
Now we just need one more brave soul to test power toggles to see if it really is a problem. If it is, contact the dev and tell 'em to declare it incompatible with this device!
Click to expand...
Click to collapse
I agree. If this app is causing this kind if an issue with the One, we need to verify and make sure that nobody else installs it. Maybe someone has a One that they are about to exchange for a different issue would be willing to test this theory for us.
Sent from my HTCONE using xda premium
I don't know about the 2G/3G facet of it (simply because it's never been noted as compatible with my device in Power Toggles), but I've used this app for a long time and I pull LTE quite comfortably.
Update: called Sprint about the issue and they notified my local Sprint store that when I brought my phone in, they were to exchange it for a new One (not refurbished) at no cost. They were out of stock and I should be receiveing it Saturday or Monday
Sent from my HTCONE using xda premium

Categories

Resources