[ONE-CLICK] Automated Freedom-Boot and TWRP installer - Kindle Fire 2 Android Development

INTRODUCING TWEEZERMOD INSTALLER
Not for the new bootloader. Make sure you are on the old bootloader.
There are two ways to use Tweezermod now!
-Desktop Version
-Cordless version (Directly from the Kindle itself!)
**WARNING**
YOU MUST HAVE ROOT ALREADY ON YOUR KINDLE FIRE 2
Just because this does not require a fastboot cable, does not mean you should not have one! Please know that there is always a chance for things to go wrong when you modify your device, and the only sure-fire way to fix things is with a fastboot cable!
Info
Tweezermod installer is an application including freedom-boot.img and TWRP for KF2. It runs a script.sh written by me, and derived from my desktop script, which was in turn derived from my method of getting CM10.1 on my own KF2 without a fastboot cable.
This package will automatically install the freedom-boot bootimage and TWRP recovery built by Hashcode.
I have tested this myself multiple times, and it is based on the method that I used the first time I installed CM10.1 prerelease on my KF2.
Installation
Desktop
Instructions:
Download
Unzip
Run the runme.sh or .bat depending on your operating system
Profit
Download:MOD EDIT LINK REMOVED
Cordless (APK)
Instructions:
Download
Install on your KF2
Open Tweezermod Installer
Press install
Grant su access
Profit
Download:MOD EDITcom.powerpoint45.FMKilo-2.apk - 10.48 MB
MD5:add2c3cb1aa1e80dfa0644ea06207a0d
If all goes well, you will see a switch from the orange Kindle Fire bootlogo to a blue one with a menu at the bottom!
Additional Info
This method uses dd to write the recovery and boot partitions, so no fastboot driver needed on windows.
If necessary, you may need to grant superuser access to adb. (You will see the superuser popup on your Kindle)
Some linux users may need to run the .sh as root.
Roms
You may have done everything here successfully at this point, BUT you will still need to choose and install a ROM. Here are the two out so far to choose from. Both have guides with them on how to install.
Powerpoint45's MooRom (With SGT7!)
Hashcode's CM10.1 Base ROM
Disclaimer:
This package comes with no warranty, nor do you have the right to sue me or my affiliates because something went wrong, and you have a brick.
If you modify this script, and you end up with a brick, I will advise everyone not to help you with your idiocy.
You are welcome to reproduce this package in its entirety, not in bits and pieces.
I did not make nor do I own the rights to the kernel or the recovery in the package.
Support:
Support for this package is offered 25/8 (whenever I'm online) either on this thread, or better yet, on freenode irc #kf2-dev
For in thread support that requires the output of the script, please use pastebin.com to post the output, and post a link to it here.
Credits:
Hashcode -- CM10.1 for KF2, Freedom-Boot, TWRP for KF2
Powerpoint45 -- Tablet UI rom for kf2, Primary tester for Hashcode, wrote and compiled tweezermod installer
FMKilo -- Figured out how to get to fastboot without a cable, Wrote cableless script, script for tweezermod installer(I commissioned him)
Special Thanks:
MisterSir69 -- Alerted me to the brick created by Desktop Script V1
DiscoGecko -- discovered the problem with and helped fix Desktop Script V4 on windows
iytrix -- Did this fancy pants layout for all the info stuff
FAQ:
Q: Why the name Tweezermod?
A: Tweezermod is a reference to the first fastboot cable I used. it was just an opened up cable, with a wire spliced into pin one. I used a pair of tweezers to contact pin 4, the one that sends the device into fastboot. Pin 4 is ironic because issuing the command idme bootmode 4 from an elevated terminal or adb shell will send the device into fastboot mode upon reboot. The only way to get out of fastboot after this is by issuing the command, fastboot -i 0x1949 oem idme bootmode 1, which reboots to system upon fastboot -i 0x1949 reboot(perhaps it is ironic in the opposite way).
The name Tweezermod is ironic in the fact that you never go to fastboot whilst installing cm by the use of the .apk or the Desktop Script.

Old Versions
Old versions are only included so you can examine them and see what exactly was changed. Please always use the current version linked in the first post.
Desktop Script
V1:BRICK WARNING DO NOT USE!
MD5: fa65668bd268d48ca1c0e563fdf07169
V2:KF2CM10.zip - 10.30 MB
MD5:4156e28006386b6c96c9190abf071b80
V3:KF2CM10.zip - 11.23 MB
MD5:25a01c57280af427091924ebe365d0ef
V4:KF2CM10.zip - 11.23 MB
MD5:e3d5aecfa2f563ded5e7bcbd3b132a7e
V5:KF2CM10.zip - 11.23 MB
MD5:c1b7703ffe1b15eeac70bbfb265646ae
V6:KF2CM10.zip - 11.24 MB
MD5:aa2b4da68fcb6f8e77ef5fc391ef30ca
Tweezermod Installer
V1:AlienBox (2).apk - 10.45 MB
MD5:ead9d23cd12e877c267adf19c243d3ae
V2:Tweezermod_Installer.apk
MD5sum: 4f2f6c805e4d28476b409a8b30fe16ca
V3:Tweezermod_Installer2.apk - 10.47 MB
MD5:1e7b518f0ad0c9d4c133cc2acd388d23
V4:com.powerpoint45.FMKilo-2.apk - 10.48 MB
MD5:add2c3cb1aa1e80dfa0644ea06207a0d
Changelog
Desktop Script
V1: Bricks(if you don't want them, throw them through my window, I can fix it...)
V2: No longer tries to create stack using adb shell, stack is now included in the archive.
V3: Adb now included for those of you who did not modify your $PATH. Also added @echo off to .bat and rearranged archive
V4: Removes install-recovery.sh and recovery image in the system partition of the stock rom.
V5: Fixed for windows. No update for linux users.
V6: Added new freedom-boot.img, now with fastboot in secondary bootloader. No need for -i 0x1949 flag.
Tweezermod Installer
V1: Actually works, in launcher, it is named Main Activity launch and grant access.
V2: Tweezermod Installer. Install this apk on your kindle fire2 press install and no profit from a system rom that won't delete twrp, secondary bootloader, and a fully functional twrp. (Roms not included.) APK by powerpoint45, script inside by me.
V3: Fixed the directory issue within V2, should work now.
V4:Added new freedom-boot.img, now with fastboot in secondary bootloader. No need for -i 0x1949 flag.
This package will be updated if any changes are made to the freedom-boot or TWRP recovery by Hashcode.
I AM OFFICIALLY DONE TRYING TO HELP ANYONE WHO USES KFU ON THEIR KF2, DO THE RESEARCH FIRST, THEN ATTEMPT THE MOD.

Downloaded this and ran the runme, Now im in bootloop. Screen just keeps flashing Kindle Fire.

Reserved

same thing! just stuck in bootloop! How do I fix this?

grantpatrickfarrell said:
same thing! just stuck in bootloop! How do I fix this?
Click to expand...
Click to collapse
the same way he did.

Just purchased a fast boot cable. Needed it anyways. Hopefully by time it comes all the bugs will be worked out.
fmkilo said:
the same way he did.
Click to expand...
Click to collapse

grantpatrickfarrell said:
Just purchased a fast boot cable. Needed it anyways. Hopefully by time it comes all the bugs will be worked out.
Click to expand...
Click to collapse
If you ordered one from SkOrPn, it should be there within the week, if you ordered one from hong kong, expect it within the month

i got this to work, but i had to run the script multiple times to finally boot into recovery. the first time i ran it the bootloader just said "booting..." forever and never booted into recovery. the second time i ran it, it booted right into recovery, but when i loaded .zips to flash and tried to boot back into recovery i just got "booting..." forever again, so i ran the script a third time and was able to boot into recovery to flash a new rom. either way, it works and you're awesome. thanks a lot.

755 said:
i got this to work, but i had to run the script multiple times to finally boot into recovery. the first time i ran it the bootloader just said "booting..." forever and never booted into recovery. the second time i ran it, it booted right into recovery, but when i loaded .zips to flash and tried to boot back into recovery i just got "booting..." forever again, so i ran the script a third time and was able to boot into recovery to flash a new rom. either way, it works and you're awesome. thanks a lot.
Click to expand...
Click to collapse
Hashcode is addressing the issues with the booting into the twrp

fmkilo said:
Hashcode is addressing the issues with the booting into the twrp
Click to expand...
Click to collapse
Awesome.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2

Good news some questions first do i need root from the start i have a fresh new kindle and i just need standard cable and the programme and new rom seems to root is a bit harder than my mobiles
Sent from my GT-I9100 using xda app-developers app

dannyling said:
Good news some questions first do i need root from the start i have a fresh new kindle and i just need standard cable and the programme and new rom seems to root is a bit harder than my mobiles
Sent from my GT-I9100 using xda app-developers app
Click to expand...
Click to collapse
you need to use the root with restore method and the qemu root method to root this device first, then come back here.

fmkilo said:
Hashcode is addressing the issues with the booting into the twrp
Click to expand...
Click to collapse
turns out, most of the problems with booting into twrp were actually people letting their devices boot stock os, without anyone realizing that there was an install-recovery.sh that would break twrp. This has been fixed in the latest version of computer one click and also tweezermod_installer.apk

fmkilo said:
turns out, most of the problems with booting into twrp were actually people letting their devices boot stock os, without anyone realizing that there was an install-recovery.sh that would break twrp. This has been fixed in the latest version of computer one click and also tweezermod_installer.apk
Click to expand...
Click to collapse
Great, so how do I know it worked and how do I boot into recovery?

Does terminal emulator work to get to twrp?
Su
Reboot recovery

Installed the apk and ran it, but nothing seems to be changed..when i su reboot recovery it doesnt boot into twrp..

What about hd

Hondologe said:
Installed the apk and ran it, but nothing seems to be changed..when i su reboot recovery it doesnt boot into twrp..
Click to expand...
Click to collapse
Does you get an orange or blue kindle fire logo when you boot.?
Edit: Just tried this myself. Not tried installing the recovery or modded boot before, and I'm not seeing a blue kindle fire logo.
The latest apk doesn't seem to work yet.
Sent using my Jelly Atrix.

restlessrob said:
What about hd
Click to expand...
Click to collapse
I mean does this work on kindle fire hd

Related

[REF] [ROM] aosp 2.3.2 .img's for crespo (Nexus S) *UPDATED 2/3/11*

Here are the 2.3.2 .img's compiled from aosp source for crespo (Nexus S)
We don't have a pure 2.3 ROM compiled from aosp source yet, so I decided build one, and here are the .img's from my build.
These can be used to restore Nexus S back to aosp, or flash all images for a pure aosp experience.
HOWEVER: These are NOT the official Google factory images for Nexus S, only compiled from source.
Attached are: system.img boot.img recovery.img userdata.img
Installation:
Code:
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
All images being provided work 100%, as I have it installed on my nexus S currently and flashed via fastboot.
disclaimer: WARNING! I am in no way shape or form responsible for ANY DAMAGE you may do to your phone. I am simply providing the files, however you decide to flash on your own, not me.
These images also do not contain any proprietary apps such as the Google apps (Maps, Market, Gmail, etc)
Clear? ok then, proceed to download
system .img link: http://www.mediafire.com/file/k2jopya0o416m8j/system.img
others are attached below.
UPDATE: these .img's are for 2.3.2
Attached bcm4329.ko module to fix wifi for users who flashed my boot.img on a non-aosp ROM (push to /system/modules)
2.3.2 OTA package
Here is the 2.3.2 ota update package for those of you who don't like/wanna use fastboot for whatever reason.
Rename as update.zip, place on sdcard and flash as usual.
http://www.mediafire.com/file/fl1nxdpleitd392/2.3.2_full_crespo-ota-eng-signed.zip
WARNING! This ota update package is fully stock, has NO ROOT or Google proprietary applications, and will revert you to the stock recovery.
Google Applications archive can be found here: http://goo-inside.me/gapps/
Atached below are the files needed to manually root: SuperUser.apk, su, busybox.
Code:
adb push SuperUser.apk /system/app
adb push su /system/xbin
adb push busybox /system/xbin
chmod 6775 /system/xbin/su
chmod 6775 /system/xbin/busybox
adb shell reboot
If terminal doesn't let you remount in adb you may have to do it through the phone. Place all root files on sdcard:
Code:
mount -o rw,remount /dev/block/mmcblk0p2 /system
cp /sdcard/SuperUser.apk /system/app/
cp /sdcard/su /system/xbin/
cp /sdcard/busybox /system/xbin/
chmod 6775 /system/xbin/su
chmod 6775 /system/xbin/busybox
Reboot with a battery pull.
reserved again. You Never know
Thanks alot I've been looking for the stock recovery img
Sent from my Nexus S using Tapatalk
brian6685 said:
Thanks alot I've been looking for the stock recovery img
Sent from my Nexus S using Tapatalk
Click to expand...
Click to collapse
The recovery image from this post sadly still does not allow to flash the update from Google.
Getting signature verification error and yes i reverted back to the boot.img posted here as well.
EDIT: the boot.img here is also breaking wifi.
thanks for the effort though
clubtech said:
The recovery image from this post sadly still does not allow to flash the update from Google.
Getting signature verification error and yes i reverted back to the boot.img posted here as well.
EDIT: the boot.img here is also breaking wifi.
thanks for the effort though
Click to expand...
Click to collapse
Why wouldn't the ota work if you were using the stock recovery? That's weird
Sent from my Nexus S using Tapatalk
clubtech said:
The recovery image from this post sadly still does not allow to flash the update from Google.
Getting signature verification error and yes i reverted back to the boot.img posted here as well.
EDIT: the boot.img here is also breaking wifi.
thanks for the effort though
Click to expand...
Click to collapse
??? I flashed everything before posting and all was working perfect. I flashed all .img's though, maybe wifi broke for having a different system image and different wifi modules than aosp.. I just flashed paul's rom and reverted to stock recovery.img without a hitch with the one I posted.
brian6685 said:
Why wouldn't the ota work if you were using the stock recovery? That's weird
Sent from my Nexus S using Tapatalk
Click to expand...
Click to collapse
That's because it is not really stock recovery, it is a recovery built from source.
I guess it does not have google's signature.
Do you know of anywhere I can get the stock recovery? Or does fastboot oem lock bring back stock recovery?
Sent from my Nexus S using Tapatalk
jroid said:
??? I flashed everything before posting and all was working perfect. I flashed all .img's though, maybe wifi broke for having a different system image and different wifi modules than aosp.. I just flashed paul's rom and reverted to stock recovery.img without a hitch with the one I posted.
Click to expand...
Click to collapse
I can install your recovery, no problem. but i am not able to use the update.zip from Google with your stock recovery (signature verification failed).
I also tried with you stock recovery and boot.img - same issue.
When i booted the device with you stock recovery + boot.img but my original (stock) system.img - wifi could not start.
clubtech said:
When i booted the device with you stock recovery + boot.img but my original (stock) system.img - wifi could not start.
Click to expand...
Click to collapse
That's probably where the problem lies. I flashed all .img's including my system.img and wifi worked perfectly
Does this include gapps?
Anderdroid said:
Does this include gapps?
Click to expand...
Click to collapse
no, they're aosp images built from source.
clubtech said:
When i booted the device with you stock recovery + boot.img but my original (stock) system.img - wifi could not start.
Click to expand...
Click to collapse
Issue fixed. Please see the OP.
Hi jroid,
I tried to compile the 2.3.1 sources from AOSP today and ran into hundrets of warnings (no errors though so I might be OK). I did some coding for linux before but have no experience building Android from source. Can you provide the steps required to build?
As far as I can tell my environment is setup properly: I did a fresk Debian 64bit, JDK 6 and all the packages listed on sources.android.com - even if the information listed there is outdated. I installed Eclipse as well but didn't use it so far because I want to get the unchanged AOSP build correctly first.
To build I ran env_setup.sh, then lunch and picked crespo, then make... that's where I'm stuck right now.
I want to get the base build correctly before starting any changes. I'd love to get this setup in a way that allows me to test the build in the emulator first and then flash to the NS... Not sure if that's the best way or using fastboot boot instead of flash to see if it's working properly directly on the device (all new to me, sorry if these are dumb questions).
I searched the forum and the wiki but didn't find general or NS specific documentation for AOSP builds...
ToSa2 said:
Hi jroid,
I tried to compile the 2.3.1 sources from AOSP today and ran into hundrets of warnings (no errors though so I might be OK). I did some coding for linux before but have no experience building Android from source. Can you provide the steps required to build?
As far as I can tell my environment is setup properly: I did a fresk Debian 64bit, JDK 6 and all the packages listed on sources.android.com - even if the information listed there is outdated. I installed Eclipse as well but didn't use it so far because I want to get the unchanged AOSP build correctly first.
To build I ran env_setup.sh, then lunch and picked crespo, then make... that's where I'm stuck right now.
I want to get the base build correctly before starting any changes. I'd love to get this setup in a way that allows me to test the build in the emulator first and then flash to the NS... Not sure if that's the best way or using fastboot boot instead of flash to see if it's working properly directly on the device (all new to me, sorry if these are dumb questions).
I searched the forum and the wiki but didn't find general or NS specific documentation for AOSP builds...
Click to expand...
Click to collapse
I'm away from my laptop right now, but get adb installed first. Repo sync then cd to /crespo and run extract-files.sh
.Build env_setup.sh
Lunch full_crespo-userdebug
Make
Warnings should be fine, I got them too and it compiled perfectly. If you get errors, u will know. The compile with stop
Sent from my Nexus S
Thanks!
I did the extract-files.sh now which I missed before - running make over night so I'll see tomorrow if I get any errors...
Any advice how to test minimizing the risk (emulator / fastboot boot)?
ToSa2 said:
Thanks!
I did the extract-files.sh now which I missed before - running make over night so I'll see tomorrow if I get any errors...
Any advice how to test minimizing the risk (emulator / fastboot boot)?
Click to expand...
Click to collapse
yea you can use the fastboot boot command to test. I personally just flashed all the images through fastboot and it booted fine. aosp 2.3.1 (which I compiled) is in my experience FASTER and more smooth than the stock rom that shipped with the NS. Call audio quality is MUCH more rich robust than it is on the factory builds. have no idea why but it is
Since the Google apps aren't included, I'm guessing they all may be downloaded/installed from the Market... is that correct?
Thanks,
jankyboy said:
Since the Google apps aren't included, I'm guessing they all may be downloaded/installed from the Market... is that correct?
Thanks,
Click to expand...
Click to collapse
no, not all. Only some, but this doesn't even include the market so you couldn't even do that. I'm compiling from source again and probably release an AOSP rom in a day or 2, maybe even today..

How to install TWRP custom recovery (no MCU updates possible afterwards)

pakidermo5000 said:
Ok, I need some help here to understand pretty basic things. I think I am trying to do the wrong thing. I get into bootloader mode. I get the black screen and detection of "class for rockchip" in device manager.
Now, I want to flash TWRP. My idea was to get into bootloader mode and use ADB to flash TWRP. But, I cannot connect to HuiFei when in bootloader mode because adb does not see any device.
Instead, if I boot the unit and use Wifi ADB, then I can connect to the unit.
So, should I flash TWRP through wifi ADB with the unit booted, or should I do it through bootloader mode? I could probably do it via recovery, but I do not really know how (just do update from sd card and select the TWRP I downloaded from 1-2-hak ?) otherwise, how do I do it if my adb does not detect any device?
sorry for the basic questions, but it is the first time I am doing this...
Click to expand...
Click to collapse
You dont need bootloader to flash TWRP. You just need to know how to get there if something goes wrong.
Check this link http://www.freaktab.com/showthread....itions-from-android-No-PC-needed-For-rockchip
get the flash_image from the link.
the get your wifi adb going
do a
adb push flash_image /sdcard/flash_image
adb push TWRP_KGL-7650G /sdcard/TWRP_KGL-7650G
then i go to adb shell
usually just cp them to dev
cd /sdcard
cp flash_image /dev/flash_image
cp TWRP_KGL-7650G /dev/TWRP_KGL-7650G
then flash it
/dev/flash_image recovery /dev/TWRP_KGL-7650G
then if you want to test
reboot recovery
you will need an mouse attached.
I am gong to see if I can get the touch working in this when I get my unit back.
Do a backup of the whole system in TWRP.
Then you are pretty well set.
Not sure if you need original recovery to update new MCU.images. When i uploaded mine I just flashed back the original recovery in the same way.
You can back up the original recovery by the steps in the link above. Which is good to have a complete copy of what you have now before tinkering too.
Hope that helps.
v3 with init.d support!
Here are v3 images for both screen resolutions in both KGL and KLD variants:
KVV_KitKat_XRESxYRES_yymmdd_rooted_light_reparted_init.d_v3:
rooted:
- ClockworkMod's Superuser apk, su binary and root daemon (root daemon needed on 4.3+ roms)
reparted: (seems popular these days )
- system reduced from 768MB to 512MB
- oem reduced from 128MB to 64MB
- data increased from 1GB to 3GB
- internal sd in now a bit less than 4GB
removed apks:
- Gmail2 (available on Play Store)
- Maps (available on Play Store)
- GoogleSearch (available on Play Store)
- VoiceSearch (included in GoogleSearch on Play Store)
- Talkback (available on Play Store)
- Google TTS and its libs and files (available on Play Store)
- Adobe Reader and its libs (available on Play Store)
- Instructions (surely useless, not relevant and badly translated from chinese...)
- Chinese and Japanese Keyboards (also removed their libs that are now useless)
- Navgear (just a stupid shortcut to the selected nav app in settings...)
updated/added apks:
- Google Play Store (updated to latest version)
- Google Play Services (updated to latest version with libs correctly installed so no more Google Play Services errors! Fixed on 1024x600 v3.1 thanks to @ESTIMULO)
- Browser bookmarks sync adapter (added, missing in KLD and KGL)
- Google calendar sync adapter (added, missing in KGL)
- Google contacts sync adapter (added, missing in KGL)
modded:
- init.d support added (late in boot process so every external storages are mounted), you can drop your scripts to /etc/init.d (chmod 755)
- added compatibility symlinks for storage mount points (it may fix issues with apps using hard-coded path to access sdcards and usb, if not it won't hurt anywway!)
- flash_image binary by Androtab, with dump_image and erase image symlinks to flash/erase/dump full partitions (dump_image return an error at the end but you can ignore it, dump is valid)
IT WILL WIPE YOUR DATA AND INTERNAL SD so backup first!
Please note that 1024x600 versions are untested as I don't own such a device but it's modded the same way so it should work flawlessly.
Updated TWRP image
This is an updated Team Win Recovery Project image based on 2.7.0.0 by Abdul from freaktabs (most credits goes to him! )
Updated fstab to new KK part scheme (was mounting kpanic and oem instead of system and internal sd)
updated kernel, modules and config files (full SElinux support)
Still no touchscreen you have to use a mouse. I've spent days trying to make touchscreen work but no luck, I'm starting to think that touchscreen is handled by mcu which then emulates a touch device or some weird things like that...
Now with a 1024x600 image
Please note that 1024x600 version is untested as I don't own such a device but it's Updated the same way so it should work.
Download latest versions HERE
How to flash recoveries back and forth to backup/restore data over flashes
Install Jack Palevich's Terminal Emulator for Android from Play Store and use a root explorer to save the apk file to your sd card or usb storage.
Download flash_image binary and use a root explorer to copy it to /system/bin and change permission to 755 rwxr-xr-x (if you are on one of my modded fw it's already installed you can skip this step).
Launch Terminal Emulator and type su to gain root, then type cd /path/to/recovery/folder, then type flash_image recovery twrp.img
You now have twrp installed, type reboot recovery to reboot to twrp.
In twrp use a mouse and go to backup menu to backup data (do not backup to internal sd it will be formatted by update).
Now reboot to system and place update.img at the root of you external sd or usb storage but don't update if prompted
Launch Terminal Emulator and type su to gain root, then type cd /path/to/recovery/folder, then type flash_image recovery recovery.img
You now have standard recovery installed, type reboot recovery to reboot to recovery.
Now you can flash update.img from the menu using power button.
When back into Android use backed up Jack Palevich's Terminal Emulator for Android apk to reinstall it quickly without having to set up google account.
Launch Terminal Emulator and type su to gain root, then type cd /path/to/recovery/folder, then type flash_image recovery twrp.img
You now have twrp installed, type reboot recovery to reboot to twrp.
In twrp use a mouse and go to restore menu to restore data.
webdude12 said:
Just a quick update.
I have copied over multiple different SU using TWRP to my stock 1024 x 600 4.4.2 unit. All them result in the same thing. Superuser not being able to use it. I have confirmed its there, messed with permissions on su and the system folders.
On thing I noticed through the TWRP command line is that SELinux is enabled. So thinking I might to research that to figure out if I need to do anything to get around that.
Back to the drawing board.
Click to expand...
Click to collapse
I've updated the twrp image for 1024x600 with 100% scaling factor so it should fit the whole screen now. Grab it HERE if you want to try.
Why don't you just flash a superuser zip from twrp, it will take care of the files, permissions and starting the daemon for you. You can grab ClockworkMod's superuser installer here: http://download.clockworkmod.com/superuser/superuser.zip
Note:
You can get required files here: https://docs.google.com/file/d/0B3FXCUVt554Mb1Nnai14eWM2cWc/edit
This is not provided by me! I copied the link from @pakidermo5000's old OP-Post
With TWRP MCU-Updates are no longer possible!
Normally you do not need TWRP as any custom roms can and have to be flashed using original recovery
coudu said:
I've updated the twrp image for 1024x600 with 100% scaling factor so it should fit the whole screen now. Grab it HERE if you want to try.
Why don't you just flash a superuser zip from twrp, it will take care of the files, permissions and starting the daemon for you. You can grab ClockworkMod's superuser installer here: http://download.clockworkmod.com/superuser/superuser.zip
Click to expand...
Click to collapse
"Twrp image" Link is dead
Guy I know this is bringing up a thread from the dead but a question. I did install TWRP but my issue is when in TWRP to do a backup it is only backing up about 60MB of data even w/ all partitions chosen. It shows 0MB in data, is there a way I can back up the entire ROM like you can do on my android based phones w/ TRWP or CM recovery? Also I've read how to switch to stock recovery but whenn I go to TWRP and backup it just backs up TWRP backup files (ext4.win) no .img file is created. I think I just need a copy of the stock recovery.img and then i'd be golden. Am I wrong? If im not, does anyone know where I can find that?
Thanks
Dave
TT_Vert said:
Guy I know this is bringing up a thread from the dead but a question. I did install TWRP but my issue is when in TWRP to do a backup it is only backing up about 60MB of data even w/ all partitions chosen. It shows 0MB in data, is there a way I can back up the entire ROM like you can do on my android based phones w/ TRWP or CM recovery? Also I've read how to switch to stock recovery but whenn I go to TWRP and backup it just backs up TWRP backup files (ext4.win) no .img file is created. I think I just need a copy of the stock recovery.img and then i'd be golden. Am I wrong? If im not, does anyone know where I can find that?
Thanks
Dave
Click to expand...
Click to collapse
Yea i need the same, managed to lose my back up of it.
Have you guys ever gotten this to back up the data partition? It always says 0mb.
Was able to take the recovery.img from a joying update.. if someone needs it let me know ill send a link.
PLEASE!!
TT_Vert said:
PLEASE!!
Click to expand...
Click to collapse
Pm'd, xda isn,t letting me post links just yet. I guess i can not be trusted. Let me know if that works for you!
Must appreciated man, it was perfect. It seems TWRP is pretty much useless on these devices for bare metal backup/recovery like they are on phones.
Courtesy of jgarci44. Stock joying recovery
hi, this talk is the TWRP recovery for rockchip 3188? Excuse my intrusion would like to know how to install on my unit "kit kat 4.4.4"
don't waste your time currently.
TT_Vert said:
don't waste your time currently.
Click to expand...
Click to collapse
Why are you saying this ? Explain.
bettuccio said:
Why are you saying this ? Explain.
Click to expand...
Click to collapse
If you have to ask how to do it, most likely you won't be able to do anything with it at this point.
Sent from my Nexus 5X using XDA-Developers mobile app
---------- Post added at 08:37 PM ---------- Previous post was at 08:31 PM ----------
bettuccio said:
Why are you saying this ? Explain.
Click to expand...
Click to collapse
If you must here is a website where I got it (although not much you can do with it) be sure to have a mouse as the touch screen doesn't work. If you need to revert, which you will if you plan to update you will need to find a copy of the stock recovery.
http://freaktab.com/forum/main-category/freaktab-downloads/11780-twrp-2-7-0-0-for-rockchip-s
Sent from my Nexus 5X using XDA-Developers mobile app
rollback recovery stock
Hi.
Do you have any idea how to get back to the recovery stock version? I installed the TWRP under Rk3188 Stereo Card, it works fine but at the time of updating the file upgrade.img does not work.
Thanks you for your help.
I have a post on this somewhere. Search for it but here is what I have documented. Here is the joying stock recovery if that'll help you. https://www.dropbox.com/s/h5o46v24911nbsp/Joying stock recovery.img?dl=0 Same process as my post on installing TWRP on these except you use this image.
Dave
Ok, let me get this straight...
1. With TWRP you can't flash mcu.img (but you can flash update.img? how does this exactly work? how do I flash an update.img from TWRP? or do I lose the ability to flash update.img as well?)
2. The ROMs do not come with recovery images and overwrite TWRP? I thought they did, like other ROMs...

[UNOFFICIAL] TWRP 3.0.0-0 for the Pixel C (dragon-ryu) :: Current: 02-11-2016-1

This is UNOFFICIAL TWRP for the Pixel C. That said, the TeamWin team greatly helped me in getting this working. But at the same time, neither TeamWin nor me take any responsibility whatsoever for any undesired outcome resulting from any kind of use of this project and project files! If you don't exactly know what you're doing then just walk away and do something good. Don't touch any options of which you don't exactly know what they're for!
What works:
* So far, everything; encryption support should work, but some feedback on this would be welcome
Problems:
* The GUI will be sometimes slow, sometimes super slow. This is probably due to the high screen resolution of the Pixel C.
How to install:
- Unlock bootloader
- In the bootloader, run "fastboot flash recovery <.img file>"
- Reboot into Pixel C bootloader
- Boot into recovery (or later on/from Android through "adb reboot recovery")
If the recovery doesn't stick after booting into Android:
- Do the install procedure as above
- Do NOT reboot into Android
- Press Vol-Down + Power until you see the bootloader menu
- Select "Boot into Android Recovery"
- When in TWRP, mount system
- Using TWRP's File Manager, or using adb, delete the file "/system/bin/install-recovery.sh"
- Reboot
After doing this, OTAs won't work any longer, but they wouldn't work anyway after installing TWRP. Just so you know
DOWNLOAD
twrp-3.0.0-0-dragon-ryu-02-11-2016-1.img
SHA1 hash: 3e97aae6cc18975683eda2bd3732faaecec14166
Changelog
:: 01-19-2016-1
- Removed screen timeout by default, since the GUI is very slow and the screen unlock slider is very hard to use
- Added an option to fix the Fastboot Full Cap flag directly from TWRP; you find the option in "Advanced". If the Pixel C should ever not let you flash in fastboot, boot into TWRP, select Advanced -> Fix Fastboot, swipe to confirm, and you're set.
:: 02-11-2016-1
- Rebased on twrp/android-6.0 branch (i.e. upgraded to TWRP 3.0.0-0)
The recovery is based on the Pixel C stock kernel.
Awesome! I can survive without root for the time being but being able to enable multiwindow would be amazing!
Thanks!
Edit: I am getting a FAILED (remote: unsupported command) error and cant flash this. Anyone know a work around?
Worked fine for me with "fastboot flash recovery [image name]" did you unlock your bootloader? Also root works just fine, you just have to boot from your PC.
Sent from my Pixel C using Tapatalk
brando56894 said:
Worked fine for me with "fastboot flash recovery [image name]" did you unlock your bootloader? Also root works just fine, you just have to boot from your PC.
Sent from my Pixel C using Tapatalk
Click to expand...
Click to collapse
I did unlock my bootloader but can't get anywhere. Tried updating my sdk, drivers everything. I guess I will have to keep playing with it.
Edit: I relocked my bootloader, and then unlocked it again and now it is working. If anyone else runs into this give it a try.
it successfully installed on my pixel c. is reachable as the Android Recovery option. and boots to bootloader to allow boot of boot.img
this is a good thing. thanks to all involved.
it's been 1 month since release and good way to celebrate.
Good work. Thanks you
hooray thanks! just to clarify: I need encryption disabled to use twrp or just to flash SuperSU?
I'm currently using phhusson's noverity boot-img to boot and with a modified vendor img root is working fine while encryption is enabled ... just having to boot via fastboot every time is a bit awkward. And since I don't know what happens if the device got stuck and reboots itselfe without the modfied boot it would be awesome to have at least a nandroid backup
doumer said:
hooray thanks! just to clarify: I need encryption disabled to use twrp or just to flash SuperSU?
I'm currently using phhusson's noverity boot-img to boot and with a modified vendor img root is working fine while encryption is enabled ... just having to boot via fastboot every time is a bit awkward. And since I don't know what happens if the device got stuck and reboots itselfe without the modfied boot it would be awesome to have at least a nandroid backup
Click to expand...
Click to collapse
Hey... You can use TWRP even with encryption enabled, you just can't write anything to /data.
However for the next build I'm going to enable TWRP's decryption option and see if it works with the Pixel C. If it does I'll post a new build this evening (European Time).
I tried the systemless SuperSU on a decrypted /data partition but it wouldn't work (bootloop), clearly there's a lot of ground to cover here, but like I said maybe the decryption functionality will help us here.
EDIT: I'm also working on a boot.img with disabled forced encryption. Looks like we're going to get proper root very soon.
cheep5k8 said:
This is UNOFFICIAL TWRP for the Pixel C. That said, the TeamWin team greatly helped me in getting this working. But at the same time, neither TeamWin nor me take any responsibility whatsoever for any undesired outcome resulting from any kind of use of this project and project files! If you don't exactly know what you're doing then just walk away and do something good. Don't touch any options of which you don't exactly know what they're for!
What works:
* Well, basically everything IN TWRP works, it's just that without a kernel that disables forced encryption this is not of very much use. I tried flashing SuperSU, but it wouldn't work properly.
Problems:
* The GUI will be sometimes slow, sometimes super slow. This is apparently still a problem with how TWRP uses the graphics mode that is used on the Pixel C. Best is if you immediately disable the screen lock once you boot into TWRP because the unlock slider is abysmally sluggish.
How to install:
- Unlock bootloader
- In the bootloader, run "fastboot flash recovery <.img file>"
- Reboot into Pixel C coreboot bootloader
- Boot into recovery (or later on/from Android through "adb reboot recovery")
DOWNLOAD
2.8.7.0-01082016-1
Click to expand...
Click to collapse
Hello thank you for this. Yesterday I tried to build as well twrp but it wasn't fully working.
I just imported this config with TW_INCLUDE_L_CRYPTO := true && TW_INCLUDE_CRYPTO := true
I didnt copy paste the twrp.fstab I added but added its path to BOAR_smthing.
Also I used omnirom's android-6.0 revision with dragon's device tree.
The recovery seems to boot, as
Code:
adb devices
returns XXXXXx recovery.
Also I can reach the device's shell with adb shell. Just the screen stays black.
I was wondering if I missed something. Is your device tree available online ?
Khaon said:
Hello thank you for this. Yesterday I tried to build as well twrp but it wasn't fully working.
I just imported this config with TW_INCLUDE_L_CRYPTO := true && TW_INCLUDE_CRYPTO := true
I didnt copy paste the twrp.fstab I added but added its path to BOAR_smthing.
Also I used omnirom's android-6.0 revision with dragon's device tree.
The recovery seems to boot, as
Code:
adb devices
returns XXXXXx recovery.
Also I can reach the device's shell with adb shell. Just the screen stays black.
I was wondering if I missed something. Is your device tree available online ?
Click to expand...
Click to collapse
Not yet. I'm going to upload it later on to the TWRP devs for official inclusion.
You need to merge the minui patch so TWRP can use DRM for video on the Pixel C; there is no fb0 device.
there were some new boot images out today. i flashed one of them. when i boot to recovery the sdcard is not able to be mounted. do you have any suggestions on what i need to do or look at in order to get it fixed?
dkryder said:
there were some new boot images out today. i flashed one of them. when i boot to recovery the sdcard is not able to be mounted. do you have any suggestions on what i need to do or look at in order to get it fixed?
Click to expand...
Click to collapse
Because /data is (force-)encrypted. I uploaded a new TWRP build with various fixes but decryption doesn't work.
What I also found out is that the boot image for the Pixel C is NOT an Android boot image (!), but a ChromeOS one. This puts a lot of things in doubt, for example I am not sure if systemless SuperSU can handle this.
But, I'm working on all that (working on boot img without forced encryption right now, but so far it doesn't want to boot completely)
OK, so, I'm running the device unencrypted now, but there are many issues still to resolve.
OK guys, if you really want actual SuperSU, and other root stuff, and decrypted /data, here's how it works but it's complicated and will only work tethered as far as I can tell.
First, download this boot image: dragon-boot-encryptable-01092016-1.img
Now here are the steps:
- make sure you have a stock boot.img handy in case something goes wrong (as usual I can not take responsibility but chances of bricking are extremely slim if you know what you're doing)
- boot into fastboot
- flash the above boot image to boot ("fastboot flash boot dragon-boot....")
- flash the TWRP recovery (latest version) ("fastboot flash recovery twrp-dragon-...")
- hold power+vol down pressed.. the device will turn off, keep it pressed even as it turns off, it will turn on again and you are in the coreboot menu
- select "Android Recovery" which will start TWRP
- in TWRP, select system as read only when it asks ("never write onto the system partition").. my boot image does not disable dm-verity which seems to be still in effect, so if you change /system, the Pixel will refuse to boot (even though it's unlocked... no idea)
- once in TWRP, go to "Wipe" and then choose at the bottom "Format Data" (just wiping will not work)
- when that's done stay in the recovery
- get SuperSU 2.66 from somewhere and flash it through TWRP (using sideload for example)
- when it's done, go to "Backup" in TWRP and only backup boot (the kernel) - no password - no compression
- somehow copy the backed up kernel from the device to your computer ("adb pull" for example), but in no case let the Pixel boot into Android
- when that's done, tell TWRP to boot back into the bootloader
Now get ready to be real quick...
- boot (just boot, not flash) the TWRP backed up boot image (it's 32MB large and called boot.emmc.win, but it's all good): "fastboot boot boot.emmc.win" (and now you have to be rather quick)
- It will boot up for a second and then go back to the "The OS will boot in 30 seconds screen"
- Again press power+vol down and hold it, even as the device turns off, until you're in the coreboot bootloader
- There, choose fastboot again
- And once again boot the boot.emmc.win image ("fastboot boot boot.emmc.win")
- Now let it boot up
- If everything went OK you should be in Android, with decrypted /data, and SuperSU should be installed and working
If you want to avoid being encrypted again (although SuperSU should survive that) you will have to boot tethered everytime using that boot.emmc.win image.
Known Issues: Somehow because /data is decrypted, "Security" settings in Android will crash. Hopefully you don't need anything in there. You might also want to skip setting a lock pattern or pin when doing the initial setup, it might crash too.
So far, I tried installing AdAway using root which worked just fine.
If someone figures out how make this untethered: you da real MVP!
Thank you sir!! I will report back if I encounter any undocumented issues.
OK so I've managed to install Xposed, was pretty straightforward except for the tethered boot. Still looking into making it untethered.
since your modified boot and no encryption it seems to be smoother in graphics. in any event, the thing worked in format of data and install of the supersu zip. so, well done.
cheep5k8 said:
How to install:
- Unlock bootloader
- In the bootloader, run "fastboot flash recovery <.img file>"
- Reboot into Pixel C coreboot bootloader
- Boot into recovery (or later on/from Android through "adb reboot recovery")
DOWNLOAD
2.8.7.0-01082016-2 UPDATE: Includes various fixes from first build; decryption of data does NOT yet work
Click to expand...
Click to collapse
So, followed these instructions and whenever I try to reboot into recovery I get the no command screen. Am I missing something? lol
Edit: So figured thats the stock recovery stuff. Got to the stock recovery but can't get into twrp
2nd Edit: I redownloaded the file and didnt rename it shorter this time and now it works...weird
cheep5k8 said:
Not yet. I'm going to upload it later on to the TWRP devs for official inclusion.
You need to merge the minui patch so TWRP can use DRM for video on the Pixel C; there is no fb0 device.
Click to expand...
Click to collapse
Thank you for those informations .
Thank you so much for this! Aside from the laggy UI, which isn't an issue since we got TWRP (f yes!!!), this is amazing. Do you foresee any issues flashing fonts? I am not familiar with ChromeOS and Android structure combination as it seems there is a lot of talk about. Flashing a file that replaces the stock fonts with the ones of my choosing hypothetically should not pose a problem to /system/fonts/, correct? Thank you for your work

[ROOT][6.0][XT1097] Systemless root for Moto X 2014

Hello, everyone!
TL;DR: You're about to perform a systemless root installation on your phone so make sure you have uninstalled Xposed Framework, uninstalled root, the device's bootloader is unlocked and your phone's boot image is in its untouched stock state. Then boot into TWRP and install SuperSU-v.279-SR3 or newer.
UPDATE 2017-01-19:
- Provided missing bootloader information regarding root. Thanks, @Charlita for the heads-up!
- Moved TL;DR section to the top.
UPDATE 2017-01-15:
- SuperSU-v.279-SR3 learned how to use systemless mode as default flashing method for Motos. This is great news as the installation process now is just a matter of flashing the SuperSU installer. The segmentation fault had been fixed on SR2 and this version also includes that fix.
- Included a TL;DR section.
UPDATE 2016-12-25:
- SuperSU-v.279-SR1 contains a regression bug regarding the "segmentation fault". Skip this version for now. I've already contacted Chainfire.
- suhide: as the Chainfire himself stated, the tool is a losing game so I'm not putting any further effort here.
UPDATE 2016-11-03:
- As of SuperSU-v2.78-SR3 boot image patching works out-of-the-box. Just install it and you're done!
- TWRP version 3.x works as expected.
- Unfortunately, SafetyNet checking fails as Google constantly updates the server-side code.
- WIP: Check if Chainfire's suhide are able to help here.
UPDATE 2016-08-08:
- Added a backup reminder.
- Added flashable zip systemless_root_enabler_by_glauberlima.zip.
After a few days playing with it, I finally managed to perform a systemless root install for our beloved Moto X 2014
Benefits:
- Install OTA updates when they arrive;
- SafetyNet checking will pass so Android Pay can be used (not available in Brazil yet).
Requirements (links below) :
- Android 6 Marshmallow
- Bootloader must be unlocked otherwise you won't be able to root your phone;
- Boot partition must be in its original untouched stock state otherwise, SuperSU installer won't be able to patch it;
- System partition must be untouched as well but a simple uninstall of applications that have changed it should be enough. This step is not mandatory but if your system partition remains changed SafetyNet checking will fail;
- Your device must be unrooted. SuperSU has the option "Completly remove root". Use it;
- If you have Xposed Framework installed, uninstall it;
- You'll need ADB and Fastboot in order to flash stock boot.img if applicable;
- TWRP. Version 3.0.2-2 works just fine. If you prefer 2x series, I highly recommend version 2.8.7.1;
- SuperSU-v2.79-SR3 zip installer (or a newer version). DO NOT TRY AN OLDER VERSION. WILL NOT WORK;
Install guide:
- Make a Nandroid backup first using TWRP;
- Uninstall Xposed Framework if applicable;
- Uninstall SuperSU;
- Connect your device to your computer via USB;
- Reboot into bootloader:
Code:
adb reboot-bootloader
- Restore stock boot partition (you can skip this step if you already been on stock boot):
Code:
fastboot flash boot xt1097_boot_stock_with_may_2016_update.img
VERY IMPORTANT: The binary file boot xt1097_boot_stock_with_may_2016_update.img is device dependent. I have extracted stock boot.img from victara May 2016 update full ROM package and put it here. If you are trying on the other variants, make sure you will use the right image.
- Reboot into Recovery (TWRP);
- Flash the attached zip file systemless_root_enabler_by_glauberlima.zip. This will set both variables SYSTEMLESS=true and BINDSYSTEMXBIN=false. Without these variables set, SuperSU will fail to systemless root the device. Feel free if you want to manually enter the commands in the Command Prompt:
Code:
adb shell "echo SYSTEMLESS=true>/data/.supersu"
adb shell "echo BINDSYSTEMXBIN=false>>/data/.supersu"
- Install SuperSU and reboot system. If the first boot fails, just wait - the second will work I promise you!
- As soon as Android UI shows up you should be systemless rooted;
- Confirm SuperSU is installed by recognizing the green icon on your app drawer;
- Open up any root app you have. The world-famous Superuser permission request dialog should pop-up;
- Install SafetyNet Helper, in order to attest your Android, is passing Google's SafetyNet checking: https://play.google.com/store/apps/details?id=com.scottyab.safetynet.sample
Now you should be good. Congrats!
Go ahead and get some systemless apps:
- Systemless Xposed Framework
- Systemless Adaway
This procedure should work for the other variants too - all you need is the original boot.img
If you need any help feel free to ask.
Attached you can find the screenshots taken from my XT1097 after the procedure
Related links:
SuperSU-v2.79-SR3:
https://download.chainfire.eu/1021/SuperSU/SR3-SuperSU-v2.79-SR3-20170114223742.zip
Latest stable SuperSU:
http://download.chainfire.eu/supersu-stable
Systemless Xposed Framework:
http://forum.xda-developers.com/xposed/unofficial-systemless-xposed-t3388268
Systemless AdAway:
http://forum.xda-developers.com/showthread.php?t=2190753
Material Design Xposed Installer:
http://forum.xda-developers.com/xposed/material-design-xposed-installer-t3137758
Minimal ADB and Fastboot:
http://forum.xda-developers.com/showthread.php?t=2317790
TWRP for Moto X 2014:
http://forum.xda-developers.com/mot...recovery-twrp-2-8-0-0-touch-recovery-t2911523
Thanks:
@Chainfire
Even if I am on stock I have to flash boot*.img?
Sent from my XT1097 using Tapatalk
rtrotsky said:
Even if I am on stock I have to flash boot*.img?
Sent from my XT1097 using Tapatalk
Click to expand...
Click to collapse
Since your device already has the untouched stock boot you don't need to flash anything.
I seem to be having trouble installing the "Systemless Xposed". It errors out with - ! Failed: Unable to extract zip file!
I have verified "systemless root - ver 2.76" and tried re-downloading the zip. Any thoughts?
jbaumert said:
I seem to be having trouble installing the "Systemless Xposed". It errors out with - ! Failed: Unable to extract zip file!
I have verified "systemless root - ver 2.76" and tried re-downloading the zip. Any thoughts?
Click to expand...
Click to collapse
Could you provide your recovery.log from TWRP so we can see the detailed logging information?
You can pull it from your device by running the following command in command prompt:
Code:
adb shell cat /tmp/recovery.log | clip
This will copy recovery.log contents to the clipboard. Paste it into notepad then save and attach here.
glauberlima said:
Could you provide your recovery.log from TWRP?
You can pull it from your device by running the following command in command prompt:
Code:
adb shell cat /tmp/recovery.log | clip[code]
This will copy contents to the clipboard. Paste it in notepad then save and attach here.[/QUOTE]
This is pretty neat. Given what I read as the requirements am I correct this only works with stock ROM? (and test will only pass on stock).
Click to expand...
Click to collapse
vpxf said:
This is pretty neat. Given what I read as the requirements am I correct this only works with stock ROM? (and test will only pass on stock).
Click to expand...
Click to collapse
Hi @vpxf
The unmodified boot.img is a requirement for SuperSU as it tries to patch the boot image on-the-fly during the install process (by the time you flash it using TWRP). If the image is not in its original state, SuperSU will fail to install in systemless mode.
Regarding your question about custom ROMs compatibility I don't know if the SafetyNet checking will pass/fail. That's a good test to perform.
glauberlima said:
Could you provide your recovery.log from TWRP so we can see the detailed logging information?
You can pull it from your device by running the following command in command prompt:
Code:
adb shell cat /tmp/recovery.log | clip
This will copy recovery.log contents to the clipboard. Paste it into notepad then save and attach here.
Click to expand...
Click to collapse
I've attached the log. I did notice "unzip: zip flags 1 and 8 are not supported".
NOTE: I was able to flash the 85.7 version found in the second post of the "Systemless Xposed" thread. The newest 86.2 is the one giving me troubles.
As glauberlima found out in the other thread, you need to re-zip the xposed installer with 7-zip (that's what i used at least) and the install will work.
bertolehm said:
As glauberlima found out in the other thread, you need to re-zip the xposed installer with 7-zip (that's what i used at least) and the install will work.
Click to expand...
Click to collapse
jbaumert said:
I've attached the log. I did notice "unzip: zip flags 1 and 8 are not supported".
NOTE: I was able to flash the 85.7 version found in the second post of the "Systemless Xposed" thread. The newest 86.2 is the one giving me troubles.
Click to expand...
Click to collapse
As stated by @bertolehm I've discussed in the other posts the exactly same issue with the zip installer you have reported @jbaumert. Take a look at them:
http://forum.xda-developers.com/showpost.php?p=67792193&postcount=1193
http://forum.xda-developers.com/showpost.php?p=67805517&postcount=1233
Regarding your device being systemless rooted check with SafetyNet Helper Sample app. If everything turns green you are good
** Duplicated **
Thanks for the tutorial.
The first boot fails, ok ; but how long is the second boot ?
I wait a long time (around 15 minutes) blocked at the first screent (static moto logo) and I stop it, reboot and reinstall my backup. I panic a little
oyoyl said:
Thanks for the tutorial.
The first boot fails, ok ; but how long is the second boot ?
I wait a long time (around 15 minutes) blocked at the first screent (static moto logo) and I stop it, reboot and reinstall my backup. I panic a little
Click to expand...
Click to collapse
Which variant is your X?
glauberlima said:
Which variant is your X?
Click to expand...
Click to collapse
XT1092
oyoyl said:
XT1092
Click to expand...
Click to collapse
15 minutes... That's definitely too much.
I'm about to update this guide with my new findings so If you don't mind I'd like to suggest you this:
Repeat the steps but this time skip the update to latest version. After the reboot access SuperSU. It should display a message regarding your su needs update. Accept it.
Make sure your nandroid backup is up to date.
Same thing, but it's possible that my boot image is not up to date and I have no other boot backup to test.
I have only a complete backup (boot + system without root), perahps I'll try later with complete restore ...
Thanks
Something went wrong, the root works fine, but when I run the SafetyNet test, I got "CTS profile match: false", I just want to keep the OTA upgrades working, if I did something wrong, is there any way to unroot and do the systemless root again?? Thankss
Hi! Hey, I followed the steps and my MotoX got stuck when rebooting after flashing. I'm trying to enter fastboot with power+Volume down but no luck so far, any idea? I hope you can help me!
oyoyl said:
Same thing, but it's possible that my boot image is not up to date and I have no other boot backup to test.
I have only a complete backup (boot + system without root), perahps I'll try later with complete restore ...
Thanks
Click to expand...
Click to collapse
OK. Just leave a reply by the time you have the result of your test.
guilhermoaraujo said:
Something went wrong, the root works fine, but when I run the SafetyNet test, I got "CTS profile match: false", I just want to keep the OTA upgrades working, if I did something wrong, is there any way to unroot and do the systemless root again?? Thankss
Click to expand...
Click to collapse
One of your installed apps modified system partition. Did you test on a completly stock image?

TWRP, ROOT and disable Encryption for Yoga Tab 3 Plus (YT-X703F/L)

TWRP is an open source, community project. TWRP development is done by roughly 4 people at this point. We also have a large support community with many people who are willing to answer questions and help people with their devices either through our IRC channel or on forums like xda-developers.
Team Win was originally formed to work on porting WiMAX to CM7 for the HTC EVO 4G. After our work on the EVO 4G we wanted to work on a project that would work on more devices than just the EVO 4G and we settled on working on a recovery. Today TWRP is the leading custom recovery for Android phones.
A custom recovery is used for installing custom software on your device. This custom software can include smaller modifications like rooting your device or even replacing the firmware of the device with a completely custom "ROM" like OmniROM
Click to expand...
Click to collapse
WARNING!!! Be careful what you do here. One mistake and the device is soft-bricked. I take no responsibility for bricked devices, lost warranty or even OTAs not working!! Booting and/or flashing files from this post is on your own risk.
Requirements
Unlocked bootloader
Yoga Tablet 3 Plus with and without LTE (YT-X703L and YT-X703F) are supported
Known Issues
WARNING! Our device uses dm-verity (verified boot). The system partition should remain read-only. Otherwise a bootloop will occur. You can flash my modified kernel or SuperSU to resolve this but OTA's are no longer possible! You have to restore a factory image or clean system backup to receive OTAs
Potentially DRM keys are lost! Pure unlocking and rooting does not cause the issue. However, there have been reports of lost DRM keys by some unknown action. It is advised to act with caution. Losing your DRM keys can lead to issues with some apps which use DRM which could then have limited or no functionality. E.g. Netflix will only stream in SD (480p). You can check with DRM info if you still have L1 security level which means DRM keys are intact.
Download
Official TWRP for YT-X703F (Wifi): twrp.me
Official TWRP for YT-X703L (LTE): twrp.me
Instructions
Install fastboot and adb on your PC, e.g. from here
Enable developer options and in there select to unlock your bootloader by enabling OEM unlock and enable USB debugging
Connect your PC to your tablet and run
Code:
adb reboot bootloader
using adb on command line. The tablet will reboot into bootloader mode where you will only see the Lenovo logo. Now you use
Code:
fastboot oem unlock-go
to unlock. This will factory reset your device
Setup the tablet again and reboot again to the bootloader
Then run
Code:
fastboot boot twrp-3.2.1-0-yt_x703f.img
to temporarily boot into TWRP. You can also flash if you are sure
Select to keep system read only when TWRP starts to avoid modification which will make OTAs impossible
Optionally flash SuperSU or Magisk in TWRP which should install system less. Keep OEM unlock enabled if you flash or modify anything
Additional Downloads
Backup of original boot, recovery and system image for YT-X703F S000936: MEGA
Modified Boot image with forceencrypt disabled and it switches off CABC fully. You need to factory reset after flashing to format data without encryption boot_yt_x703f_s000963_noforceencrypt_cabc.img (YT-X703F S000963) / boot_yt_x703l_s000963_noforceencrypt_cabc.img (YT-X703L S000963) . Use
Code:
fastboot flash boot boot_yt_x703f_s000963_noforceencrypt_cabc.img
to flash the kernel in fastboot. SuperSU or Magisk should be flashed afterwards if root is desired.
Full factory images with flash tool and instructions YT_X703F_S000689, YT_X703L_S000704, YT_X703F_S000725, YT_X703L_S000725, YT_X703F_S000734, YT_X703L_S000734, YT_X703L_S000744, YT-X703F_S000744, YT-X703L_S000963, YT-X703F_S000963 and OTA updates: MEGA (These images contain the individual boot, recovery and system images that you need to restore from any modification mentioned above)
System Updates (OTA)
In order to successfully apply Lenovo system updates after root you have to restore the original boot, recovery (if you flashed TWRP) and system partitions from your current installed version (e.g. S000744) for your variant of the tablet. This will NOT delete your apps and data but will unroot. Note that OTAs are block based and always check the contents of most of the partitions. This means that all of these partitions (except your data) have to be original and have to be on the exact same version (e.g. S000734) for the update to succeed.
See here for instructions how to restore the partitions with fastboot.
Credits
@pogo1975 - for providing the factory images and fixing the AV sync issue
@launcher20 and @deecept - for testing the LTE version
TeamWin
Changelog
v4:
Now official TWRP with version 3.0.3-0
v3:
enable full disk encryption for access to the encrypted data partition
update TWRP kernel to latest S000725 version
v2:
add support for LTE variant (YT-X703L)
add further mount points to be able to backup more data
Thanks buddy! You are an absolute champion! Tell me what you need me to do and I'll do it before rooting and up load what you need.
Doing good work here.
Who wants to bet on a race between matshias and Lenovo support for who can fix the issues with this device first?
That's great and fast, I'm thinking tab 3 plus is getting hot now.
Great to see there is something moving for the yoga now. You think it will support the lte Version anytime? Or maybee even lineageos?
so you know, i've managed to install xposed thanks to this thread https://forum.xda-developers.com/xposed/unofficial-systemless-xposed-t3388268 and is working well.
wayney said:
Thanks buddy! You are an absolute champion! Tell me what you need me to do and I'll do it before rooting and up load what you need.
Click to expand...
Click to collapse
Well if you haven't modified anything yet then it'd be great if you can boot into TWRP with system read only and then connect via ADB to the tablet with a big SD card inserted which has enough free space (4 GB).
The run the following command
Code:
dd if=/dev/block/bootdevice/by-name/system of=/sdcard1/system.img
This will take a while. Then copy the file system.img from your SD card to a PC and zip it (or 7z, rar). Then upload it
Gogoho said:
Great to see there is something moving for the yoga now. You think it will support the lte Version anytime? Or maybee even lineageos?
Click to expand...
Click to collapse
The LTE variant is probably very similar and it wouldn't be much work. But I don't own the device, so I would need some help. So someone with the LTE variant who is not afraid to experiment with fastboot and adb and who can provide me with the details needed I am happy to compile a TWRP for it.
LineageOS is much much more work than TWRP. For an experienced cyanogenmod/LineageOS dev it is not much of a thing and would take only a few days, especially since it is a Qualcomm device and there are already ports for devices with SD 652. But for me this is new as well so it'll take much longer. As soon as I have time I'll look into it.
matshias said:
Well if you haven't modified anything yet then it'd be great if you can boot into TWRP with system read only and then connect via ADB to the tablet with a big SD card inserted which has enough free space (4 GB).
The run the following command
Code:
dd if=/dev/block/bootdevice/by-name/system of=/sdcard1/system.img
This will take a while. Then copy the file system.img from your SD card to a PC and zip it (or 7z, rar). Then upload it
Click to expand...
Click to collapse
You forgot to tell me to go to adb shell :silly:
DD is currently doing a dump, non interactive so I hope it is still alive, it has been close to 1 hour so far. I will upload the clean image once it is done and await further instructions from you. :good:
I'm in Perth, Western Australia (UTC +8:00), so we might be playing timezone tag.
wayney said:
You forgot to tell me to go to adb shell :silly:
DD is currently doing a dump, non interactive so I hope it is still alive, it has been close to 1 hour so far. I will upload the clean image once it is done and await further instructions from you. :good:
I'm in Perth, Western Australia (UTC +8:00), so we might be playing timezone tag.
Click to expand...
Click to collapse
I think I forgot one more thing. The external SD card needs to be mounted in the TWRP menu. I believe it's not mounted automatically. So the DD command does nothing. It shouldn't take that long. Sorry about that!
It's UTC +1:00 here in Germany
matshias said:
Well if you haven't modified anything yet then it'd be great if you can boot into TWRP with system read only and then connect via ADB to the tablet with a big SD card inserted which has enough free space (4 GB).
The run the following command
Code:
dd if=/dev/block/bootdevice/by-name/system of=/sdcard1/system.img
This will take a while. Then copy the file system.img from your SD card to a PC and zip it (or 7z, rar). Then upload it
Click to expand...
Click to collapse
matshias said:
I think I forgot one more thing. The external SD card needs to be mounted in the TWRP menu. I believe it's not mounted automatically. So the DD command does nothing. It shouldn't take that long. Sorry about that!
It's UTC +1:00 here in Germany
Click to expand...
Click to collapse
I was wondering why nothing was happening after 3 hours.
I have rared it and it is uploading at the moment, it is going to take 5 hours.
wayney said:
I was wondering why nothing was happening after 3 hours.
I have rared it and it is uploading at the moment, it is going to take 5 hours.
Click to expand...
Click to collapse
Wow ok. Well thanks a lot for your efforts. This will not just help me but anyone with modified system partition to get OTAs.
Unmodified System Image
Here is the vanilla image via DD of the system partition.
Software Version : YT-X703F_160817
Android Version : 6.0.1
Security Patch Level : 1 September 2016
Kernel Version : 3.10.84-perf
Build Number : YT-X703F_S000689_161105_ROW
Tablet purchased retail from Australia.
https://mega.nz/#!bos0GIjI!vcO9dpSJX...Grjb7k3z6mjnqA
wayney said:
Here is the vanilla image via DD of the system partition.
Software Version : YT-X703F_160817
Android Version : 6.0.1
Security Patch Level : 1 September 2016
Kernel Version : 3.10.84-perf
Build Number : YT-X703F_S000689_161105_ROW
Tablet purchased retail from Australia.
https://mega.nz/#!bos0GIjI
Click to expand...
Click to collapse
Perfect!!
Can you send me the key for the download via PM or post it?
matshias said:
Perfect!!
Can you send me the key for the download via PM or post it?
Click to expand...
Click to collapse
Let's try that again.
https://mega.nz/#!bos0GIjI!vcO9dpSJXp6cKtdH07Kt0RSaqpqQ7Grjb7k3z6mjnqA
matshias said:
Wow ok. Well thanks a lot for your efforts. This will not just help me but anyone with modified system partition to get OTAs.
Click to expand...
Click to collapse
Thank you guys for spending times on it, it would be wonderful if Lenovo people do thing like this way, too.
In the depths of the Russian Internet i have found this
YT-X703F_USR_S000689_1611051146_Q00237_ROW.zip
https://drive.google.com/drive/folders/0B_jGuhC9WsNfYUZzZmhRY2NhQlU?usp=sharing
it is supose to be complete image to Wifi-Version.
I HAVE NOT FLASHED THIS YET. Do it on your risk.
pogo1975 said:
In the depths of the Russian Internet i have found this
YT-X703F_USR_S000689_1611051146_Q00237_ROW.zip
https://drive.google.com/drive/folders/0B_jGuhC9WsNfYUZzZmhRY2NhQlU?usp=sharing
it is supose to be complete image to Wifi-Version.
I HAVE NOT FLASHED THIS YET. Do it on your risk.
Click to expand...
Click to collapse
Hahaha got to love the dark corner of the Russian internets :laugh:
pogo1975 said:
In the depths of the Russian Internet i have found this
YT-X703F_USR_S000689_1611051146_Q00237_ROW.zip
https://drive.google.com/drive/folders/0B_jGuhC9WsNfYUZzZmhRY2NhQlU?usp=sharing
it is supose to be complete image to Wifi-Version.
I HAVE NOT FLASHED THIS YET. Do it on your risk.
Click to expand...
Click to collapse
If that's real it would have saved me a lot of time finding the loophole in the system to extract the boot and recovery image. But still a great find which will rescue some soft-bricked devices.
matshias said:
If that's real it would have saved me a lot of time finding the loophole in the system to extract the boot and recovery image. But still a great find which will rescue some soft-bricked devices.
Click to expand...
Click to collapse
so long as it's safe and not loaded with malware...

Categories

Resources