Database Develop

[Q] Problem Rooting LG Optimus 2x

Hi all,
So I've tried lots of forums on here about how to root my LG Optimus 2x but keep running into the same problem. Here are the steps I've been following:
Remove the battery.
Plug in your USB cable to your PC.
Hold Volume Up and Volume Down at the same time keeping them held down.
Plug in the USB cable to your phone. (Keep the buttons held until Windows detects a new APX device.)
Open Device Manager in Windows and you should see "APX Device" listed with an error icon.
Right click on the APX device.
Select 'Update driver software'.
Select 'Browse my computer...'.
Select 'Let me pick...'.
Select 'Have disk'.
Browse to directory you extracted the *driver* software to: One-Click-G2x-recovery-flasher-09-23\APX.
Accept any warnings, including the big red alert (you may need to disable UAC).
Now in Device Manager under 'USB Controllers' you should have an 'NVIDIA USB Boot-recovery driver for mobile devices'.
If not, uninstall the driver, reboot, rinse and repeat.
I'm on a Windows 7 32 bit PC. When I check for an APX device in the Device manager I don't see one?
I do see an unknown device but when I try to click have disk etc for this, it does not recognise the drivers I'm pointing at and does not install. Can anyone help me with this?
Many thanks,
Derek

What version are you on? Froyo or Gingerbread? It seems you are flashing CWM but that's a longer way to root. You could always try Super one click, which works on froyo.

Yes, I am on 2.2. So Superoneclick is safe to use?

Absolutely. I used it when I was on froyo. Do you have any sensitive data however on your phone? Just in case you mess up, it's always good to have a backup of it. Probably hook up your USB cable to your pc/laptop and copy/paste the files to be safe.

Ok, thanks. So I have rooted the phone using SuperOneClick. Can you send me a link where I can find information about how to put on Gingerbread 2.3 now? Or maybe there is a better ROM I can use that that? Any advice would be appreicated.
Thanks,
Derek

You can try Cyanogen Mod, but that is experimental, even the RC one (Release Candidate).
You can try other leaked versions of ROMs, or you can download the latest v10L Gingerbread release. Before installing any ROM, I recommend doing a CWM or Nandroid backup.
The link to download gingerbread (it's only out in a few countries in Europe) is located in the development sub section of the LG 2x forums. However, try using the update tool and see if it tells you that you have an update.

I seem to have a bit of a problem. I took your advice and found a forum that helped me to do a Nandroid Backup. As part of the steps it asked me to install ROM manager from the Market. I started this and chose my phone model. I started the Flash ClockworkMod Recovery’ in the ROM manager but it stopped and said a permissions error occured. Then I tried to open other programs but they wouldn't open. I tried to reboot the phone but now it just flashes on the LG logo and won't boot up. Please help me with this.

Hello people on this great forum i am new here so i salud you all.
i installed Cyanogenmod 2.3.4 android on lg optimus 2x butt here is the thing how do you update to a newer version or do you have to unstall everything and start from scratch.any tips are welcome and is there a new version of cyanogenmod

derbeast said:
Hi all,
So I've tried lots of forums on here about how to root my LG Optimus 2x but keep running into the same problem. Here are the steps I've been following:
Remove the battery.
Plug in your USB cable to your PC.
Hold Volume Up and Volume Down at the same time keeping them held down.
Plug in the USB cable to your phone. (Keep the buttons held until Windows detects a new APX device.)
Open Device Manager in Windows and you should see "APX Device" listed with an error icon.
Right click on the APX device.
Select 'Update driver software'.
Select 'Browse my computer...'.
Select 'Let me pick...'.
Select 'Have disk'.
Browse to directory you extracted the *driver* software to: One-Click-G2x-recovery-flasher-09-23\APX.
Accept any warnings, including the big red alert (you may need to disable UAC).
Now in Device Manager under 'USB Controllers' you should have an 'NVIDIA USB Boot-recovery driver for mobile devices'.
If not, uninstall the driver, reboot, rinse and repeat.
I'm on a Windows 7 32 bit PC. When I check for an APX device in the Device manager I don't see one?
I do see an unknown device but when I try to click have disk etc for this, it does not recognise the drivers I'm pointing at and does not install. Can anyone help me with this?
Many thanks,
Derek
Click to expand...
Click to collapse
Only select the DEBUG USB, and its ok!
Settings > Applications.
I hope this help, because you can only do the root with the DEBUG USB activate

[Q] Go back from Rogers GB to ATT Froyo

I updated from ATT firmware to Rogers V20C.
I don't like the update since it doesn't support Spanish, that I need to use for my wife.
Also, I wasn't able to make the FM radio work.
I want to go back to ATT original firmware
I tried 'Recovery Phone' in the LGMobile Support tool, but it tells me that this model can't be updated.
How can I go back to the original firmware?

https://rapidshare.com/#!download|2...391931|R~8193971AC5B3613D32ECF33EA9EC4787|0|0
Fallow that link to dl bin for thrill then flash using bin flash lgflashtool
thrillin

Link for how to in general section o3d forum or in our dev section you pick where to look and enjoy
thrillin

link to lgflashtool download?
could you pls?

Go to o3d forum general section then look its the first post its a sticky
thrillin

adixtra said:
IN ENGLISH
Read the update at the bottom
(18 SEPTEMBER 2011)
NOTE !!!!!
Before installation, uninstall all LG's programs and drivers from your computer.
Tested on Windows XP.​
Download all these files.
http://csmg.lgmobile.com:9002/data/Setup_LGFlashTool_1.1.zip
https://rapidshare.com/files/2393374474/file.zip
http://csmg.lgmobile.com:9002/swdata/WEBSW/LGP920/AVIVML/20110623_05/OMAPFlashInstaller-4.10(2).zip
http://csmg.lgmobile.com:9002/data/LGUnitedModemDriver_WHQL_ML_Ver_4.9.7_All_Win7_LGEAll.zip
LGFLASHTool 1.2 http://forum.xda-developers.com/showpost.php?p=19094799&postcount=107
Thread with Optimus 3d Roms in *.bin format. http://forum.xda-developers.com/showthread.php?t=1246678Thanks to nasirahmed
1.Extract "Setup_LGFlashTool_1.1.zip" and Install.
2.Extract "file.zip" and put "LGFlashTool.exe" to location where you installed "Setup_LGFlashTool_1.1.zip" (default: C:\LG\LGFlashTool\)
3.Extract and Install "OMAPFlashInstaller-4.10(2).zip"
4.Exract "LGUnitedModemDriver_WHQL_ML_Ver_4.9.7_All_Win7_LGEAll.zip" and Install "LGUnitedMobileDriver_S497CA20_WHQL_ML_Ver_1.0.exe " and "LGUnitedMobileDriver_S497MA20_WHQL_ML_Ver_1.0.exe "
5.Turn Off phone, Remove your phone's SIM and SD cards.
6.Press and hold voll up button in phone.
7.When u holding "voll up button" connect the USB cable.
8.When computer detects the new hardware (Omap4430) release "voll up button".
9.Driver Installation:
a.
b.
c.
d.
e.
f.
g.
10.After Driver installation, go to device manager and change the port "LGE CDMA USB SERIAL PORT" to "com41".
a.
b.As I wrote above, you must change the port for "LGE CDMA USB SERIAL PORT" not for "LGE Mobile USB serial port" as pictured.
c.
d.
11.Run LGFlashTool.
12.In DLL select file for p920 or p920h ( from here http://forum.xda-developers.com/showthread.php?t=1246678"
13.In S/W select only *.bin file from downloaded rom.
14. Choice (Check) "USB" and click OK.
15. Click on Port COM settings(COM plug icon)
16.Check as on photos.
a.
b.
17. Click start(The Port 1 window should appear READY).
18. Disconnects USB cable and wait 5 seconds.
19. Press and hold voll up button in phone and connect USB cable.
20. The update process will begin automatically after that release the "vol up".
21.When the progress bar reaches 100%, Power ON the phone.
WARNING!!!
If the update process has stopped for a longer time (about 5 minutes) not disconnect the phone from USB, , press and hold Vol Up + Power and wait when update process resume.
You do this on your own risk!​
Jeśli widzicie błędy, piszcie.
UPDATE 18 SEPTEMBER 2011​
To flashing rom with LGFLASHTOOL without errors you need right USB cable.
Between 4 and 5 pin you have to solder resistor 910 Kohm.
The update process is the same ,but u don't need press any button when connect USB cable to phone.
Phone screen during update
This fix update screen isue
After flashing the phone will restart.
Update screen appears again(don't disconnect usb cable from phone and don't close LGDLASHTOOL)
Please wait until you see the info about error of OTA update.
After that the phone rebots and power On automaticaly.
Thanx to Marti701
Click to expand...
Click to collapse
thrillin
thrillin

There ya go enjoy
thrillin

[Q] need help if someone can...

ok i tryied to use all in one tool and i want to flash to ics to my thrill but as far as i got is on the tool it goes to stage 2 but waiting for device stays there even after i do place to battery in it.. it acts all over again as if it cant find the driver for cosmo i think that is what it is called....but im running windows 7

When it says waiting on device try pulling out the usb and then plug it right back in. I use to have to do that, but if that doesn't work then it may be a driver issue.
Maybe start the tool and when it says waiting for omap4430 device, hold down vol+ and plug in your phone but don't let go of vol+. Pop in battery like normal and it should boot you into download mode. See if that helps get your LG Cosmo driver to install, though it should install as LGE CDMA USB SERIAL PORT. if that doesn't happen, as a last resort uninstall all LG mobile drivers, reboot cpu, download the files from step 1 and step 5 of this post---> http://forum.xda-developers.com/showthread.php?p=39269819 (bag of goodies and wkparks 1.21) Turn off your anti virus and windows defender before doing anything. Once thats done unzip the two files mentioned above. Run the omap flash installer and re install both Sets of LG mobile drivers in the bag of goodies package (second set will pop up a warning for unsigned drivers a few times; hit YES do it anyways, and then re install omap by directing the driver update to the windows drivers folder in the wkparks bootloader1.21 tool. Hopefully this helps.
Here is a much better explaination from drastic00's tutorial. Follow these steps to the T and you should be flashing in no time
" A) Uninstall any LG Drivers:
a1) Open Programs and Features through Control Panel
a2)Find any drivers called "LG United Mobile Driver." Right click and select Uninstall, let it work.
a3)Reboot your pc!
B) Be sure you disabled antivirus/Windows Defender, etc. before unpacking these files.
C) Install OMAP4430 by running "OMAPFlashInstaller."
NOTE: if you have Fastboot installed SKIP this step (if you don't know, you don't have it...), but DO link the driver as in f4.
D) Install the two LG Drivers in the “LG United Mobile Drivers” folder: These are “LGUnitedMobileDriver_S497CA20_WHQL_ML_Ver_1. 0” and “LGUnitedMobileDriver_S497MA20_WHQL_ML_Ver_1. 0” The second one will warn it is unsigned, choose to install anyway (you will have to insist on this a few times here).
E)Reboot your pc!
F)Install PC/phone drivers:
f1)Shut down your phone. Remove external sd card, SIM card and battery.
f2) Open Device Manager from Control Panel
f3) Hold volume up on phone and connect to USB port. Keep holding volume up.
f4)Look for "OMAP4430" blinking on and off in Device Manager with a yellow question mark under "Other Devices." (You can let go of the phone). If you do not see it, look for "TI Boards" blinking in device manager and quickly open the arrow. Then uninstall that OMAP4430 (right click, check box to uninstall device and driver, confirm), disconnect phone and reconnect with volume up. Then...
f.4.1) You will need to 'catch' OMAP4430 (with yellow question mark) by right-clicking on it when it appears under "Other Devices." Choose "Update Driver Software."
f.4.2) Pick "Browse my computer for driver software." Then "Let me pick..."
f.4.3) Leave "All..." selected under Devices. Then "Have Disk."
f.4.4) Navigate to the omap4boot-for_optimus-v1.21 folder and choose "omap_winusb" in the usb_drv_windows folder.
f.4.5) Windows will warn the driver is unsigned. Install anyway. An OMAP4430 device should appear under the list of devices. Confirm the selection. Let the driver install.
f.4.6) Disconnect the phone and again reconnect with volume up held.
f5) You should see a popup at the bottom of your screen about drivers (the LG USB drivers) installing. (If you do not see it, disconnect phone, reboot your pc, and again connect it without battery while holding volume up). When you do see drivers installing, let go of the volume button. Click the popup to see the progress. Let it finish.
f6) Look for “LGE CDMA USB SERIAL PORT” in Device Manager. Right click on it and go to Properties
f7) Select the "Port Settings" tab and click 'Advanced'.
f8) Change 'COM Port Number:' to COM41. Click OK, then OK again.
f9) Disconnect your phone from the PC." (From drastic00's noob tutorial)
Sent from my LG-P925g using xda premium

[Q] HELP!

Hi everyone,
So while I was updating my lg2x to 4.0.4 it got interrupted! I found my phone shut off so I tried to turn it on and it worked even though the LG support tool said the update was not completed but when I opened it, it was working fine with 4.0.4 system BUT after a day it turned off!! I couldn't turn it on anymore, it won't work!! I send it to LG company in my country and they told me they don't know how to deal with it! (lg 2x didn't get released in my country!) I really don't know what to do!? can somebody help me??! :crying: :crying:

It seems you have a hardver problem, but may be not.
Download V30A ics rom.
Download AIO TOOLKIT and install it.
Remove battery from your phone
Connect USB cable to the phone while you are pressing and holding voulme_up and volume_down button.
Stat AIO-TOOLKIT
Select option "I" (capital i) to install APX (NVFLASH recovery) and follow the instrucitons.
Then select option 4 on the next screen option 1 and on the next screen select 1 again, then select 2, hit enter then type "ok" and hit enter
Wait until the process is finished.
Remove phone.
Insert battery then turn it on.
It will boot up into a wierd menu, don't be afraid of that
If it booted up turn off your phone by removing battery
In AIO-TOOLKIT select option 5 hten option 1 then drag and drop the v30A.kdz file to the AIO-Toolkit window and hit enter.
After the extraction press "N"
The extracted files are in the V30A_00 folder where AIO-Toolkit was installed.
Select option 7 in AIO-toolkit then option "a"
"SmartFlash Tool" window appears
Select ROM copy D/L
In the CP bin section select the "P990_CP.fls" file (you extracted it before, it is in the V30C_00 folder)
In the Ap bin section select the "P990_AP.bin" file (it is next to the "P990_CP.fls" file in the V30C_00 folder)
Insert battery again to you phone.
Connect USB cable while you are pressing and holding volume_down button. Hold it until a screen appears telling you that "S/W download".
You can release the button.
Press start in SmartFlash window.
If it the smartflashing process fails due Timeout error, keep trying. Remove batter then do it again from number 21. If it still fails try to flash only P990_CP.fls until it succesfully finished then try to flash P990_AP.bin until it finishes

bitdomo said:
It seems you have a hardver problem, but may be not.
Download V30A ics rom.
Download AIO TOOLKIT and install it.
Remove battery from your phone
Connect USB cable to the phone while you are pressing and holding voulme_up and volume_down button.
Stat AIO-TOOLKIT
Select option "I" (capital i) to install APX (NVFLASH recovery) and follow the instrucitons.
Then select option 4 on the next screen option 1 and on the next screen select 1 again, then select 2, hit enter then type "ok" and hit enter
Wait until the process is finished.
Remove phone.
Insert battery then turn it on.
It will boot up into a wierd menu, don't be afraid of that
If it booted up turn off your phone by removing battery
In AIO-TOOLKIT select option 5 hten option 1 then drag and drop the v30A.kdz file to the AIO-Toolkit window and hit enter.
After the extraction press "N"
The extracted files are in the V30A_00 folder where AIO-Toolkit was installed.
Select option 7 in AIO-toolkit then option "a"
"SmartFlash Tool" window appears
Select ROM copy D/L
In the CP bin section select the "P990_CP.fls" file (you extracted it before, it is in the V30C_00 folder)
In the Ap bin section select the "P990_AP.bin" file (it is next to the "P990_CP.fls" file in the V30C_00 folder)
Insert battery again to you phone.
Connect USB cable while you are pressing and holding volume_down button. Hold it until a screen appears telling you that "S/W download".
You can release the button.
Press start in SmartFlash window.
If it the smartflashing process fails due Timeout error, keep trying. Remove batter then do it again from number 21. If it still fails try to flash only P990_CP.fls until it succesfully finished then try to flash P990_AP.bin until it finishes
Click to expand...
Click to collapse
Thank you so so so much~!
but I only got through the 7th step!! so when I selected option 2 it told me to "Change layout to NEW ICS Partition layout and Unlocked BL" and honestly I don't know how to do so!? can you help me with this too, please?!
sorry for any disturbing!

bessi96 said:
Thank you so so so much~!
but I only got through the 7th step!! so when I selected option 2 it told me to "Change layout to NEW ICS Partition layout and Unlocked BL" and honestly I don't know how to do so!? can you help me with this too, please?!
sorry for any disturbing!
Click to expand...
Click to collapse
Do a screenshot, please. If you want to make it quick, then install Team viewer and send me your ID and password in e-mail: [email protected]

I sent my ID and password~! and here is a screenshot~

What I see from this picture is that you didn't installed the drivers or you didn't connected the phone properly or your phone is truly dead
I didn't get the e-mail
send me a private message in xda then

so I resend my ID and password! I accidently send it to another person!
I hope you got it now!

Problem solved. :highfive:

@bitdomo
Just wanted to know if I can use the list you put in the 2nd post.....good detailed info in it for using the AIOT
I would like to put this in the sticky thread and if possible (if I have any space left in my signature) in my signature too
Thanks my friend

SREEPRAJAY said:
@bitdomo
Just wanted to know if I can use the list you put in the 2nd post.....good detailed info in it for using the AIOT
I would like to put this in the sticky thread and if possible (if I have any space left in my signature) in my signature too
Thanks my friend
Click to expand...
Click to collapse
Yes, you can.
Sent from my LG-P990 using xda app-developers app

bitdomo said:
Yes, you can.
Sent from my LG-P990 using xda app-developers app
Click to expand...
Click to collapse
thanks my friend
luckily my thanks was your 100th too
Best wishes

[ROM][JB4.2.2] Lenovo IdeaTab A3000-H Call - A3000_A422_011_022_140127_WW_CALL_FUSE

NOTE : These Firmwares developed by Lenovo, not me.
I am just helping people to take advantage from their Lenovo A3000-H by Giving small guides and resources.
Click to expand...
Click to collapse
Here is the Lenovo A3000-H Android 4.2.2 Firmware With the Calling Option..
Flash Tool Inside the RAR Archive (If not found inside rar Archive, Just download it separately from Download Section)
Click to expand...
Click to collapse
Here is a Small Guide How To Install the Firmware (I assume you already Installed the Lenovo Drivers
- See Download Section For Drivers)
Click to expand...
Click to collapse
** Short note to Install Drivers Quickly, Download the drivers package and extract it into a new folder in your desktop, open device manager and wait..
- then switch off the tab, connect the cable to your computer and tab, device manager will show a new device something like MT65xx,
- right click it and click " Update Driver Software, then select " Browse from My Computer " and Select the extracted Driver folder from your desktop, Click Next..
- It will Install Drivers, If any confirmations asking " Do You Want to Continue " or " Do You Want to Install " Just click " YES "
- For Windows 8 and 8.1, You must restart your PC in Driver Signature Enforcement Mode (Search on Internet how to Disable Driver Signature Enforcement in Windows 8). After Booting into that Mode, Follow above Instructions.
WARNING : DO NOT TOUCH THE OPTION " FORMAT " IN THE FLASH TOOL.
IF YOU FORMAT YOU WILL LOSE YOUR TAB's IMEI NUMBER & WIFI MAC ADDRESS.
Click to expand...
Click to collapse
IMPORTANT : BEFORE YOU PLAY AROUND, IT IS BETTER YOU TAKE A BACKUP OF YOUR " NVRAM " FOLDER FROM ROOT ==>> data ==>> nvram
COPY THE COMPLETE " nvram " FOLDER TO YOUR SD CARD AND KEEP A COPY IN YOUR PC.
THIS nvram FOLDER CONTAINS YOUR IMEI, WIFI MAC, SERIAL NUMBER AND OTHER IMPORTANT DATA.
Click to expand...
Click to collapse
1. Unpack the RAR archive to Somewhere in Your Computer (Me Extracted to a Folder in Desktop)
(You will find 4 Folders Inside the rar Named : modemdb, SP_Flash_Tool_NEW, SP_Flash_Tool_OLD, target_bin)
- Some Firmwares does not contain all the folders. So don't worry about that, Just the Important folder is target_bin.
2. Open " SP_Flash_Tool_OLD " Folder, There You Will Find a Blue Icon, Flash_tool.exe file
3. Double Click Flash_tool.exe (If you are using windows Vista/ 7/ 8/ 8.1 Right Click the Flash_tool.exe and Run As Administrator.
4. Then the Flashtool will Open up.. There you can Find Lots of Options.. Be careful, Do not Click any other Options until u get a knowledge about that, otherwise your Device will be Ruined..
5. Now Click the " Scatter-loading " In the Top Right Corner of the Tool, then Navigate to the Extracted Firmware Folder, and goto the target_bin, there you will find a file named " MT6589_Android_scatter_emmc.txt " Select that file and Click " Open "
6. Make Sure " DA DL All with check sum " option is Ticked
** NOTE : If " FAC " is not selected, please tick the FAC option and click on the name " FAC " it will give you file explorer to select the FAC file
then select " FAC.img " file from the firmware folder. (This only applicable for A3000_A422_* and later firmwares)
7. Now Switch off the tablet, wait for 15 seconds And Prepare the USB cable, And Click " DOWNLOAD " (in case if you get any error messages when you click DOWNLOAD, then Please Click " FIRMWARE->UPGRADE " option) then wait 5 Seconds and Connect the USB cable to the Tablet. It will Start Flashing. A yellow Bar will appear, It will take 3 to 5 Minutes to Finish the flash Operation. Do not Disconnect until that. Finally A small Green Round Box Appear, That means Everything Success.. Now Disconnect the Cable and Start the Tablet
It will take Few Minutes to start the Tablet First time, So wait Patiently. After Start It will ask you to select the language, Select English or any language you want.. and Configre time and Everything.. Thats all.
Click to expand...
Click to collapse
VIDEO TUTORIAL :
Click to expand...
Click to collapse
DOWNLOADS
Click to expand...
Click to collapse
Android 4.2.2 Latest Firmware With All Languages & FUSE Partition
A3000_A422_011_022_140127_WW_CALL_FUSE
Firmware Released on 27th January 2014..
CLICK HERE TO DOWNLOAD A3000_A422_011_022_140127_WW_CALL_FUSE FIRMWARE
انقر هنا لتحميل أحدث البرامج الثابتة حزمة.
Click to expand...
Click to collapse
OTHER (OLD) DOWNLOADS - IN THE FOLDER (FOR ADVANCED USERS ONLY )
CLICK HERE TO OPEN THE DOWNLOADS FOLDER!
Click to expand...
Click to collapse
UPDATED Drivers (23rd February 2014) (Flash and ADB) : http://www.mediafire.com/download/juzwauwy9rx9yw6/Drivers_v1.2.zip
Click to expand...
Click to collapse
Latest Flash Tool : http://www.mediafire.com/download/k0lpbxp5fmuvpzu/SP_Flash_Tool_exe_v3.1328.0.183.zip
.

Recovery and Gapps
TWRP Recovery and Gapps (OPTIONAL - ONLY FOR ADVANCED USERS )
Click to expand...
Click to collapse
** RECOVERY INSTALLATION ALSO SAME LIKE INSTALLING FIRMWARE. JUST LOAD THE SCATTER FILE FROM THE RECOVERY PACKAGE AND HIT DOWNLOAD! IF ANY WARNINGS APPEARS, JUST IGNORE THEM!
Install this TWRP RECOVERY ONLY If You are Running " A3000_A422_000_006_130517_WW_CALL " Firmware!
CLICK HERE TO DOWNLOAD TWRP RECOVERY FOR " A3000_A422_000_006_130517_WW_CALL " FIRMWARE
Click to expand...
Click to collapse
Install this TWRP RECOVERY ONLY If You are Running " A3000_A421_000_029_130327_CN_3G " Firmware!
CLICK HERE TO DOWNLOAD TWRP RECOVERY FOR " A3000_A421_000_029_130327_CN_3G " FIRMWARE
Click to expand...
Click to collapse
Install This GAPPS after Installing " A3000_A421_000_029_130327_CN_3G " Firmware and Recovery..
** Put the GAPPS Package on a Memory card and Install through TWRP Recovery
CLICK HERE TO DOWNLOAD GAPPS FOR A421
Click to expand...
Click to collapse
Use framroot to root your tab.
Download : CLICK HERE TO DOWNLOAD FRAMROOT 1.6.0 APK
Click to expand...
Click to collapse
Check here How to Install GAPPS manually using Root Explorer..
Note : Your Tab must be rooted before Install the Gapps manually..
Extract the gapps zip package somewhere in your memory card using computer before copy.
Click to expand...
Click to collapse
Some Screenshots!

Does this firmware include the "fused" internal storage partitions, a single 13GB partition instead of one 1GB for apps and one 12GB for other?

MrBeck said:
Does this firmware include the "fused" internal storage partitions, a single 13GB partition instead of one 1GB for apps and one 12GB for other?
Click to expand...
Click to collapse
It Includes 1GB for Apps and 12GB For Files

Lenovo drivers
how can i install the lenovo a3000 drivers? via PC or on the tablet itself?

bedrock0220 said:
how can i install the lenovo a3000 drivers? via PC or on the tablet itself?
Click to expand...
Click to collapse
Download the drivers package, extract it to the desktop. Then Open flash tool and Initialize the flashing procedure, then hit download and connect the tablet to the pc, it will ask to install drivers, if not then goto device manager, u can see there your device right click it and click update drivers, then give the extracted location of the drivers. it will install.

Point 7 is not clear ! why wait seconds ?!
* What means prepare usb cable to plug it or to prepare it ?!
* All previous points should be done while USB connected to pc ?

lenovo a3000
Sir,
I followed your instruction on installing driver via device mgr and the result is driver is updated.I followed your instruction on flashing and when off my tab and push the download button and wait 5 secs after that to connect the USB to pc. But when I push the download the flasher started reading and the bar is in pink color, when I put my USB after 5 secs there is no reaction on the flasher, only on my tab has an icon of battery and under charging.PLEASE HELP.
note: my tab FW already jb 4.2.2 without call function.

jazmy said:
Point 7 is not clear ! why wait seconds ?!
* What means prepare usb cable to plug it or to prepare it ?!
* All previous points should be done while USB connected to pc ?
Click to expand...
Click to collapse
After Turning off the tablet, it is better you wait few seconds before connecting to pc for flashing.
You Should not Connect the Cable to the tablet Before 7th Stage, All previous points should be done WITHOUT CONNECTING USB to PC.
You Should connect the Cable after You Click the Button " DOWNLOAD "

bedrock0220 said:
Sir,
I followed your instruction on installing driver via device mgr and the result is driver is updated.I followed your instruction on flashing and when off my tab and push the download button and wait 5 secs after that to connect the USB to pc. But when I push the download the flasher started reading and the bar is in pink color, when I put my USB after 5 secs there is no reaction on the flasher, only on my tab has an icon of battery and under charging.PLEASE HELP.
note: my tab FW already jb 4.2.2 without call function.
Click to expand...
Click to collapse
After you hit the DOWNLOAD button connect the Cable to the tablet. If its started in charging Mode(tab has an icon of battery and under charging) Just reset the tablet while its connected to the pc. Reset button is near the 2nd SIM Slot.

azam426 said:
After you hit the DOWNLOAD button connect the Cable to the tablet. If its started in charging Mode(tab has an icon of battery and under charging) Just reset the tablet while its connected to the pc. Reset button is near the 2nd SIM Slot.
Click to expand...
Click to collapse
i followed your instruction sir to reset it while connected to PC but still no response on the flasher, no yellow bar status either.any other suggestion for such result?

bedrock0220 said:
i followed your instruction sir to reset it while connected to PC but still no response on the flasher, no yellow bar status either.any other suggestion for such result?
Click to expand...
Click to collapse
Can you check the device manager after connecting the tab to pc??? see is there any un installed drivers left there or not..

azam426 said:
After you hit the DOWNLOAD button connect the Cable to the tablet. If its started in charging Mode(tab has an icon of battery and under charging) Just reset the tablet while its connected to the pc. Reset button is near the 2nd SIM Slot.
Click to expand...
Click to collapse
Sir, i just followed your instruction to rest the tab while it is connected to the PC but still no response from the flasher, even yellow bar status is not present. i transfer the device to other usb ports but after i push the DOWNLOAD button but the PC is looking for MTK65xx driver? so the flashing did not push thru. where can i get this driver?
i 2x check the device manager for my tab that is connected to PC, i only found out portable device with 2 drives (D,E) and some usb ports. i update the drivers of both using the file locations but it is up to date.
please help...
---------- Post added at 02:17 PM ---------- Previous post was at 02:12 PM ----------
azam426 said:
After you hit the DOWNLOAD button connect the Cable to the tablet. If its started in charging Mode(tab has an icon of battery and under charging) Just reset the tablet while its connected to the pc. Reset button is near the 2nd SIM Slot.
Click to expand...
Click to collapse
Sir, i just followed your instruction to rest the tab while it is connected to the PC but still no response from the flasher, even yellow bar status is not present. i transfer the device to other usb ports but after i push the DOWNLOAD button but the PC is looking for MTK65xx driver? so the flashing did not push thru. where can i get this driver?
i 2x check the device manager for my tab that is connected to PC, i only found out portable device with 2 drives (D,E) and some usb ports. i update the drivers of both using the file locations but it is up to date.
please help...
---------- Post added at 02:27 PM ---------- Previous post was at 02:17 PM ----------
i check the device manager and i think all drivers are already installed. any other solution for me to try?

azam426 said:
After you hit the DOWNLOAD button connect the Cable to the tablet. If its started in charging Mode(tab has an icon of battery and under charging) Just reset the tablet while its connected to the pc. Reset button is near the 2nd SIM Slot.
Click to expand...
Click to collapse
I didn't try it yet but maybe bedrock0220 has different Jellybean version !!

check the screenshot of my tab maybe it will help...TY

bedrock0220 said:
check the screenshot of my tab maybe it will help...TY
Click to expand...
Click to collapse
do i need to off my tab before i go to device manager?
is there a USB debugging or developer option on the tab that i will open?

bedrock0220 said:
Sir, i just followed your instruction to rest the tab while it is connected to the PC but still no response from the flasher, even yellow bar status is not present. i transfer the device to other usb ports but after i push the DOWNLOAD button but the PC is looking for MTK65xx driver? so the flashing did not push thru. where can i get this driver?
i 2x check the device manager for my tab that is connected to PC, i only found out portable device with 2 drives (D,E) and some usb ports. i update the drivers of both using the file locations but it is up to date.
please help...
---------- Post added at 02:17 PM ---------- Previous post was at 02:12 PM ----------
[/COLOR]
Sir, i just followed your instruction to rest the tab while it is connected to the PC but still no response from the flasher, even yellow bar status is not present. i transfer the device to other usb ports but after i push the DOWNLOAD button but the PC is looking for MTK65xx driver? so the flashing did not push thru. where can i get this driver?
i 2x check the device manager for my tab that is connected to PC, i only found out portable device with 2 drives (D,E) and some usb ports. i update the drivers of both using the file locations but it is up to date.
please help...
---------- Post added at 02:27 PM ---------- Previous post was at 02:17 PM ----------
i check the device manager and i think all drivers are already installed. any other solution for me to try?
Click to expand...
Click to collapse
Try the Drivers From Next Post, Download it, Extract it then double click install.bat it will install Drivers. Then try to flash.
Your tab should be always off when you do flash operations (Install flash drivers, flash new firmware etc) by connecting the USB cable

New usb flash driver!
NEW USB FLASH DRIVER!
Try to Install this Driver and Flash... :good:

bedrock0220 said:
do i need to off my tab before i go to device manager?
is there a USB debugging or developer option on the tab that i will open?
Click to expand...
Click to collapse
I am Busy today, Inshaallah tomorrow i will try to Make a Video Tutorial for Install Drivers, firmware etc..

Firmware upgrade
Hi.....We need to press "Download" or "Firmware-Upgrade". If I press "Download", I am getting message to press "Firmware-Upgrade".
Thanks,