Related
laptop no longer recognizes tilt or tytn; changed usb cables; rebooted both devices and laptop; no go..
mssg I get is "one of the usb devices attached to this computer has malfunctioned. and windows does not recognize it"; any suggestions; cannot sunc nor tether via ISharing.
tia
a in yul said:
laptop no longer recognizes tilt or tytn; changed usb cables; rebooted both devices and laptop; no go..
mssg I get is "one of the usb devices attached to this computer has malfunctioned. and windows does not recognize it"; any suggestions; cannot sunc nor tether via ISharing.
tia
Click to expand...
Click to collapse
Hi
First of all try to reinstall Microsoft ActiveSync, than in the ActiveSync options, in your device, be sure that in "Connections..." setting "Synchronize all PC by this connection" is checked and below "USB" showed!
Otherwise, if your device, when connected to the PC, also doesn't charge (if you have this option enebled on your PDA!) there is some problem on your PC settings concerning the USB! Try to connect to someother PC to test it!
Ciao
thx...
@[email protected] said:
Hi
First of all try to reinstall Microsoft ActiveSync, than in the ActiveSync options, in your device, be sure that in "Connections..." setting "Synchronize all PC by this connection" is checked and below "USB" showed!
Otherwise, if your device, when connected to the PC, also doesn't charge (if you have this option enebled on your PDA!) there is some problem on your PC settings concerning the USB! Try to connect to someother PC to test it!
Ciao
Click to expand...
Click to collapse
hello there, first n foremost thanks for your input!
Before trying out your possible solution i tried to connect and for some reason i was able to connect via the device today...??!!
i really dont know why, but will try your soln if this situation reocurrs.
NB: this happenned to me twice in the last 3-4 months, n i never figured out the cause ??
any other advice or ideas gratefully accepted.;
its probably the same as me and loads of other people - the pins have bent on your usb connector - probably caused by using non standard chargers and usb leads. Its been widely reported. The non-standard leads have too much space around them when plugged in and wiggle causing the connector on the tytn II to bend. Try using the lead which came in the box and see if it helps. and try using the charger that came with it too.
Can bent pins be fixed?
Hello -- I'm one of those people with a non-recognition problem. Is it possible to fix the bent pins? My problem seems to have begun around the time I lost my original USB cable. Now, all the cables I have -- ones that have been specifically sold to work with my HTC Tilt -- have the symmetrical, sort-of-trapezoidal mini-usb connection, rather than the rectangle-with-one-corner-cut-off shape of the original cable. I should say these cables do charge my device, but none of my computers recognizes it as a USB device.
Help?
Thank you,
J. Georgia
bent pins continued
I should add that the charging cable that originally came with my phone has the same connector shape, so I'm not sure what's going on.
USB Device not recognised
This is known to happen at times win Windows, and not just for the TYTN2 but a myriad of devices.
The fastest fix for this:
Reboot ur PC/ Laptop.
If this Doesn't help - Then add in a reboot for the TYTN 2 also.
The problem will go away for some time.
I know its annoying, but this is way faster than troubleshooting for contacting MicroShaft Support.
axeman said:
This is known to happen at times win Windows, and not just for the TYTN2 but a myriad of devices.
The fastest fix for this:
Reboot ur PC/ Laptop.
If this Doesn't help - Then add in a reboot for the TYTN 2 also.
The problem will go away for some time.
I know its annoying, but this is way faster than troubleshooting for contacting MicroShaft Support.
Click to expand...
Click to collapse
Unfortunately this is no soution for me. I seem to have this problem as well, since about two weeks.
I use two notebooks (Dell & Acer) and both do not show any activity when connecting my Kaiser to the original USB cable. The device is not even switched on when I connect it, nor does this happen when I connect it to the (original) cable in my car, which did work before.
Charging works fine, both in the car and when connected to both notebooks, but no Sync at all.
I have tried another USB-cable with the same result, so I suspect some hardware-problem causing me to be unable to copy files between my notebook and my phone and worse, rendering me unable to flash a new ROM onto it.
Who knows what to do next?
I am mystified, too. USB Charging and audio connections work. I have rebooted my computer and done a soft reset on my phone several times, to no effect. I uninstalled and reinstalled Windows Mobile Device Center. Still nothing at all via USB. Once, yesterday, I somehow got a Bluetooth connection long enough to sync, but haven't been able to since then. Even then, Windows Media and AudibleManager couldn't see the phone. The really weird thing is, I can see the phone connection in my Bluetooth manager, but even with all the proper boxes checked, I can't sync. When I try from my device, I get an empty progress box which disappears after a fraction of a second. When I try from my computer, it says the device is not connected, but doesn't give me any option to connect.
Would a hard reset help?
If so, would returning an unlocked AT&T Tilt to factory defaults lock it back up? And what do I do if it does?
Please help!
J. Georgia
I have had similar problems with my touch pro in the past, even bluetooth internet sharing eventually gave up the ghost.
I tried a myriad of leads and then eventually reinstalled active sync- which did the trick.
USB sync not working
[email protected] said:
I am mystified, too. USB Charging and audio connections work. I have rebooted my computer and done a soft reset on my phone several times, to no effect. I uninstalled and reinstalled Windows Mobile Device Center. Still nothing at all via USB. Once, yesterday, I somehow got a Bluetooth connection long enough to sync, but haven't been able to since then. Even then, Windows Media and AudibleManager couldn't see the phone. The really weird thing is, I can see the phone connection in my Bluetooth manager, but even with all the proper boxes checked, I can't sync. When I try from my device, I get an empty progress box which disappears after a fraction of a second. When I try from my computer, it says the device is not connected, but doesn't give me any option to connect.
Would a hard reset help?
If so, would returning an unlocked AT&T Tilt to factory defaults lock it back up? And what do I do if it does?
Please help!
J. Georgia
Click to expand...
Click to collapse
I've had the same problem with my first Tilt. There's multiple threads that detail this known problem. Some seem to be due to bent pins, some are general hardware failures (possibly the USB controller). There are some HardSPL images out there that have a "force usb" option enabled. This never worked for me, but it might be worth a shot for you.
...a word of warning....
If you end up reflashing your phone (via MicroSD) and the flash goes bad, you may be stuck, as many of the solutions for repairing a bad flash require you to USB sync. My first Tilt was a victim of this after a bad stock ROM flash that left my device without audio, and unable to flash via MicroSD.
replace usb board
you need to replace your usb board. It will run you less than $10 if you do it yourself. you can get the board on ebay
really? 4 years later?
Hey guys I realy could do with some help here
When I connect my bran new x1 to my laptop (vista 32)
I get this message....
"One of the devices attached to this computer has malfunctioned and windows dose not recognize it for assistance in solving this problem click this message."
And then i get...
"This device has malfunctioned try reconnecting the device or replace it"
I sometimes had this problem on my last x1 but it worked after few reconnection's (my other usb devices allways work fine and so did my first 2 x1s). After trying over 40 times with different ports and different usb
Cables I assumed that it must be a problem with my laptop.
so I did a full destructive restore totally wiped everything off my laptop. Turned it back on and got a different message when I connected the phone.
"Windows mobile adapter has failed"
I typed this into google looking for a solution and found a few random forums that showed other people had had the same problem in Aug 14, 2008, March 17, 2008. a problem thats over a year old will have been fixed I thought. So ill have to wait for windows update to finnish.
After 16 hours of vista updating and resetting updating and resetting i plugged the x1 in and got this message
"usb devise not recognized. One of the devices attached to this computer has malfunctioned and windows dose not recognize it for assistance in solving this problem click this message."
And then i get...
"This device has malfunctioned try reconnecting the device or replace it"
iv updated all my drivers. iv tried Microsoft's fix it tool that scans your computer for errors and it came back with....
"No problems have been detected on your system."
Iv been on the tech guys website.
Iv tried different usb cables,
Istalling windows mobile device center makes no difference,
Iv even tried it on a different computer (running xp)
and still no joy! xp fails to find settings and asks for the cd that came with the device (I didnt get one with this phone (x1)so I used the one from the old phone(x1i) this didnt work and it also gave the option of searching for settings on the internet, this didnt work ither!
Surely theres something iv missed I cant have had 4 Sony Ericsson x1s and they've all been ****ed? each have had different problems. iv tried phoning Sony Ericsson support all they say is send it off for repair but how many times do I have to send these things off? its beyond a joke! I just want one that works!
Any help with my usb problem would be highly appreciated.
Is anybody els having the same problems?
AAAAAAHHHHHHHHHHH
It could be a problem with the software on my phone coz my insurence companie sent me this letter.....
dear re:j 47299
please be advised that the following return of your mobile phone to our service center and your consequent request for the refund postage that upon further inspection of this unit we have found that your issue dose not fall into either "engineering failure" or "parts failure" and therefore dose does not qualify under our refund policy,
we have enclosed your receipt for your reference and assure you of a our prompt and personal attention at all times
yours sincerely
administration
but becouse the usb connection dosnt work I cant update the software or flash a rom (sd card method requires hard spl - hard spl requires usb) anybody know of a way round this?
(I have an sd card reader and bluetooth dongle)
w.i.n.d.l.e said:
but becouse the usb connection dosnt work I cant update the software or flash a rom (sd card method requires hard spl - hard spl requires usb) anybody know of a way round this?
(I have an sd card reader and bluetooth dongle)
Click to expand...
Click to collapse
Generic roms don't need to be HardSPL'd to flash via Micro SD method.
Download one of the generic roms and extract the nbh file (if it's an .exe use winrar to extract the file), rename kovsimg.nbh, whack it on the micro sd card and put the phone into boot loader mode (hold vol down and power when turning on).
Once you have flashed the generic rom, check to see if the usb connection works properly on this version before making any changes.
You should try and get your phone back to stock before sending it away for warranty repair.
You are using Vista, what did you expect lol?
i gave up trying to sync with vista on my laptop. i use xp and active sync.
wish you good luck bro
quite shocked when saw a screen break xperia, lol
I had a Motorola MPx220 which had this problem (I was using XP at the time), the socket on the phone motherboard had gone bad.
If XP is asking for drivers, you need to install ActiveSync first. If you've had 4 X1s and they haven't worked on your Vista computer it is probably your computer. Go back to the XP computer, install ActiveSync (download it off microsoft.com) and try again!
Vista does work with the X1. I think I'm not the only person who can testify to this. It is possible that your computer is not supplying enough power through the USB port- in this case you need to disable charging over a computer USB port on your phone.
have you tried other usb ports? i've had no problems. even on vista 64 or win7 64. i did had problems once, my pc didn't recognize my xperia, but it was to a faulty usb cable, maybe that's your problem too.
Check the settings on your phone. Settings, USB to PC, uncheck that checkbox under ActiveSync. Oh, and switch to Windows 7, bro.
Every now and then (say once every 3 months) I get over-zealous with adding USB ports to my laptop. It comes with two ports standard but I have another two through the use of a PCMCIA extension slot. Say I have a 2.5 HDD, 3.5 HDD, printer and wireless router connected at the same time, most of the ports go bonko.
Thats the source of the "One of the USB Devices has Malfunctioned" warnings. I think its just collectively, there is not enough power to run them efficiently at the same time. Changing USB ports or disconnecting some of the devices tend to work for me.
w.i.n.d.l.e said:
Hey guys I realy could do with some help here
AAAAAAHHHHHHHHHHH
Click to expand...
Click to collapse
Was that photoshop'ed?
the screen is off an iphone lol its a drag and drop via ms paint.
id like to jump up and down on my x1 then force feed it to vodafone
yes iv had 4 x1s but this is the first that wont connect to my laptop
many great suggestions here! some things I havnt tryed yet and im glad to hear I can still flash roms. thanks guys ill let you know how i get on
Pretty sure it's a problem with WMDC caused by a windows update.
You have to delete the device, uninstall WMDC (fully) and reinstall. I'll see if I can find the instructions again.
EDIT:
Uninstall WMDC and WMDC driver update and reinstall the latest WMDC.
OR
Try:
1. Keep your device connected
2. Press START+r and enter "devmgmt.msc" (without the quotation marks).
3. Look under the "Network adapters" node for "Microsoft Windows Mobile Remote Adapter". If this is not present, skip to step 4. Otherwise, right-click "Microsoft Windows Mobile Remote Adapter" and choose to "Uninstall"
4. Look under the "Mobile Devices" node for "Microsoft USB Sync". If this is not present, skip to step 5. Otherwise, right-click "Microsoft USB Sync" and choose to "Uninstall"
5. Disconnect and reconnect your device. Your device driver will re-install and Windows Mobile Device Center will launch.
Then:
6. restart your PC
7. uninstalling (make sure you click the box to remove associated software) both WMDC and WMDC driver update
7. install the latest WMDC 6.1 from link above.
8. restart your PC
Hi everyone,
I'm having issues connecting my Samsung Captivate to my computer. For about a week, it worked fine, I was able to transfer files to my phone but recently I noticed that the "USB connected" notification is not showing on the phone when plugged in to the computer.
Now, when I plug in my phone to the computer it just charges but doesn't comunicate with my computer. A friend of mine bought the same phone right after I did and he gets the "USB connected" connected when he plugs in his.
I tried using his USB cable but again, the phone is not recognized by Windows nor the phone detects it is connected to the computer. I've tried installing several USB drivers that I've come across on several forums, but nothing. I even downloaded and updated Kies to the latest version, but still nothing.
My phone is unlocked and NOT rooted, and I'm using Windows 7 x64. I've set the USB Settings to Mass Storage, even to Ask on Connection, but it doesn't ask anything when I connect the phone to a USB on my computer.
Sometimes Windows knows there is a device connected but says it couldn't recognize it.
I already did a factory reset, but the issue was not solved. I've tried connecting it to other computers, but still hasn't been able to connect my phone correctly.
What could it be?
Thanks!
Hmm. You have Mass Storage selected and up-to-date USB drivers. Try selecting USB-Debugging and Stay Awake in the Development option of your phone. If that doesn't fix it, then I have a few other ideas.
Make sure the usb door is completely open, it should click into place, some users have reported this solves their usb issues.
I did what you told me, but still my phone ain't recognized by Windows nor my phone is aware that it has been conected to a computer
What other ideas do you have in mind?
catire said:
Make sure the usb door is completely open, it should click into place, some users have reported this solves their usb issues.
Click to expand...
Click to collapse
I'm sure usb door is completely opened
Have you tried using a different USB outlet on your computer? I had this same issue when I plugged my phone up using the USB outlet on the front of my computer then when I tried the one on the back of my computer it worked just fine.
Are you running a launcher app? I use launcher pro and can't connect until I change back to the default launcher with home switcher and launch it.
jgchaval said:
I did what you told me, but still my phone ain't recognized by Windows nor my phone is aware that it has been conected to a computer
What other ideas do you have in mind?
Click to expand...
Click to collapse
First off, think back. If it worked for a week and then suddenly stopped, what changed? Maybe you updated something on Windows or changed something on your phone. There's a reason it just stopped.
You can try using a free program called USBDeview.
It might do the trick for you and help you install the correct drivers. I'm thinking you no longer have them.
1. Download USBDeview (link is above)
2. Plug your phone in and open the program. Find all the HTC drivers-delete them
3. Unplug your phone and plug it back in
4. The correct drivers should install automatically
You can also try updating the drivers manually.
Galaxy S drivers (These are for ADB, but will work fine)
1. Click the Start Menu on your computer and right click "Computer"
2. Choose "Manage" --> it will ask you to continue --> "Device Manager"
3. Plug you phone in and look for it to pop up, probably under Portable Devices
4. Right click --> "Properties" --> "Update Driver" --> "Browse" --> "Let Me Pick" --> and navigate to the location you extracted the drivers to.
This is most likely a driver issue. I doubt your phone is messed up. You'll get it eventually. I also had a hard time getting my Captivate to connect. After uninstalling and reinstalling my drivers (more than once) it finally worked. One last thing, for now. When you uninstall drivers, also make sure you don't have any installed under your program list. As in, Control Panel --> Uninstall a program. Good luck!
climber1872000 said:
Have you tried using a different USB outlet on your computer? I had this same issue when I plugged my phone up using the USB outlet on the front of my computer then when I tried the one on the back of my computer it worked just fine.
Click to expand...
Click to collapse
A friend of mine, who bought the same phone on the same day as I did, plugged in his phone on my computer using my cable to the same port my phone was connected, and he did get the "USB Connected" notification on his phone
govgeek said:
Are you running a launcher app? I use launcher pro and can't connect until I change back to the default launcher with home switcher and launch it.
Click to expand...
Click to collapse
No, i'm using the default launcher that comes with the Captivate
jgchaval said:
Hi everyone,
I'm having issues connecting my Samsung Captivate to my computer. For about a week, it worked fine, I was able to transfer files to my phone but recently I noticed that the "USB connected" notification is not showing on the phone when plugged in to the computer.
Now, when I plug in my phone to the computer it just charges but doesn't comunicate with my computer. A friend of mine bought the same phone right after I did and he gets the "USB connected" connected when he plugs in his.
I tried using his USB cable but again, the phone is not recognized by Windows nor the phone detects it is connected to the computer. I've tried installing several USB drivers that I've come across on several forums, but nothing. I even downloaded and updated Kies to the latest version, but still nothing.
My phone is unlocked and NOT rooted, and I'm using Windows 7 x64. I've set the USB Settings to Mass Storage, even to Ask on Connection, but it doesn't ask anything when I connect the phone to a USB on my computer.
Sometimes Windows knows there is a device connected but says it couldn't recognize it.
I already did a factory reset, but the issue was not solved. I've tried connecting it to other computers, but still hasn't been able to connect my phone correctly.
What could it be?
Thanks!
Click to expand...
Click to collapse
I just did the new AT&T update and mine is now having this problem. I have to manually go into manage applications > usb settings > mass storage to get it to work now
a.n said:
First off, think back. If it worked for a week and then suddenly stopped, what changed? Maybe you updated something on Windows or changed something on your phone. There's a reason it just stopped.
You can try using a free program called USBDeview.
It might do the trick for you and help you install the correct drivers. I'm thinking you no longer have them.
1. Download USBDeview (link is above)
2. Plug your phone in and open the program. Find all the HTC drivers-delete them
3. Unplug your phone and plug it back in
4. The correct drivers should install automatically
You can also try updating the drivers manually.
Galaxy S drivers (These are for ADB, but will work fine)
1. Click the Start Menu on your computer and right click "Computer"
2. Choose "Manage" --> it will ask you to continue --> "Device Manager"
3. Plug you phone in and look for it to pop up, probably under Portable Devices
4. Right click --> "Properties" --> "Update Driver" --> "Browse" --> "Let Me Pick" --> and navigate to the location you extracted the drivers to.
This is most likely a driver issue. I doubt your phone is messed up. You'll get it eventually. I also had a hard time getting my Captivate to connect. After uninstalling and reinstalling my drivers (more than once) it finally worked. One last thing, for now. When you uninstall drivers, also make sure you don't have any installed under your program list. As in, Control Panel --> Uninstall a program. Good luck!
Click to expand...
Click to collapse
I did all that yesterday, but the device ain't listed in the USBDeview nor it shows up in the Device Manager
did you finally fix this problem? because I'm having the same issue here
Same here. It was working fine, I could connect to Kies, transfer music in Media mode and see both sd drives in Mass Storage mode. Then I rooted today and now I get nothing. In anything but Kies mode I get the Windows Bong of Recognition, but still not visible in Explorer. Also, my Home screen stays active instead of switching to the USB animation like it did before. I know this can't be a consequence of rooting the phone, can it?
EDIT: More weirdness, with the phone connected in Mass Storage mode if I look at My Computer in Explorer there are 2 extra drives showing, but they are greyed out and when I click on either of them it asks me to insert a card as the drive is empty. WTF???
UPDATE: I unrooted and managed to get my USB connection back to working. It is still a bit flaky as I sometimes have to disconnect/reconnect several times before it works, but at least it now works although it sometimes loses sync in the middle of transferring a file. Can't imagine why simply rooting the phone would cause the loss of USB connectivity. I am going to reroot and see if it occurs again.
OK, a rerooted the phone and this problem is now back. I have no problem connecting while in debugging mode. I installed OCD (non-Market apps mod) and when I turn off debugging and connect I get the Windows bong and see the USB icon in the Notification bar, but the MTP screen never comes up and I can't see the phone in Explorer (Mass Storage mode) or in WMP (Media mode). Kies can;t see it in that mode, either. I really don't want to have to unroot every time I want to look at the phone contents. Any ideas? PLEASE!
I'm having a similar problem - I installed the Perception ROM and immediately afterwards I can't see the USB connection at all from my PC or my Mac. The USB icon on the phone does not come up either.
I'm trying to get my hands on a different cable - but the weird thing is when I plug the USB into my computer the phone starts charging for like half a second and then stops.
This is really annoying. I tried changing the rom to Cognition 3.02 but that didn't change anything.
There are a few topics on this here on the forum - I would recommend the following:
How are you rooting your phones? Nobody has said exactly how they are doing this. Are you using recommended rooting methods? Or are you using some app found on the market?
Make sure you have USB De-Bugging is turned on.
Make sure you have it listed as ask on connection.
For those who can see the drives in Windows...
Plug in your phone and then pull down your notification bar and click on the USB connected message. It will give you an option there to mount your SDCard(s) to Windows allowing you to transfer files.
Kies is junk - I'd recommend uninstalling it as it seems to cause more issues then it solves.
Use the drivers I have posted in the Q&A section (these are the ones that are linked in Design Gears Odin 1 Click Back to Stock post btw) - but I would try and COMPLETELY removing the pre-existing drivers before installing the new ones.
Make sure the USB Cable is plugged into the back USB port that is directly on your motherboard - this will ensure it's not a computer/hardware related issue.
I know of one user who had to go through his computer and manually remove all remnants of other drivers. I have my phone connected to both a Windows XP 32bit and a Windows 764bit systems and have been lucky to not have any USB issues.
If none of that works - I'd suggest taking it to your nearest AT&T/Rodgers shop and see if they can get the phone to connect (make sure it's back to stock!). If not they should warranty replace the device.
avgjoegeek said:
There are a few topics on this here on the forum - I would recommend the following:
How are you rooting your phones? Nobody has said exactly how they are doing this. Are you using recommended rooting methods? Or are you using some app found on the market?
Make sure you have USB De-Bugging is turned on.
Make sure you have it listed as ask on connection.
For those who can see the drives in Windows...
Plug in your phone and then pull down your notification bar and click on the USB connected message. It will give you an option there to mount your SDCard(s) to Windows allowing you to transfer files.
Kies is junk - I'd recommend uninstalling it as it seems to cause more issues then it solves.
Use the drivers I have posted in the Q&A section (these are the ones that are linked in Design Gears Odin 1 Click Back to Stock post btw) - but I would try and COMPLETELY removing the pre-existing drivers before installing the new ones.
Make sure the USB Cable is plugged into the back USB port that is directly on your motherboard - this will ensure it's not a computer/hardware related issue.
I know of one user who had to go through his computer and manually remove all remnants of other drivers. I have my phone connected to both a Windows XP 32bit and a Windows 764bit systems and have been lucky to not have any USB issues.
If none of that works - I'd suggest taking it to your nearest AT&T/Rodgers shop and see if they can get the phone to connect (make sure it's back to stock!). If not they should warranty replace the device.
Click to expand...
Click to collapse
This isn't my first rodeo... But to answer your questions:
I used the rooting method posted in XDA forums - the one-click rooting.
I've used the drivers included in the xda-forum. Not the kies software.
The only thing that changed was the loading of a new custom rom. The cable works (confirmed on my friend's phone). I can't get odin to restore back to stock because I can't get the computer to recognize the phone in either normal or in download mode. I've restored to stock using the jh7 in the stickied q&a thread
I don't think it's a hardware issue either - I think it's software-based. I'm going to try to take it to an at&t store today at lunch to see what they say.
I also have that problem only I noticed it when I cleared the dalvik cache. It messed up the auto rotate so it was always sideways and now I have no connectivity to the PC. Let me know how ATT treats you.
greeto4 said:
I also have that problem only I noticed it when I cleared the dalvik cache. It messed up the auto rotate so it was always sideways and now I have no connectivity to the PC. Let me know how ATT treats you.
Click to expand...
Click to collapse
What rom are you on
Does anyone else have this problem? When I connect my phone to either my laptop (winXP) or my desktop (win7x64) I periodically - constantly, really - get this message:
"One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message."
When I click the message, it identifies my phone as a Generic USB Hub (4 ports) with the first child being a USB Mass Storage Device, the second being the problematic "Unknown Device" and the last two are "Unused Port"s.
This happens whether the phone is in charge-only or mass storage mode. I tried installing the autoplay drivers and that didn't help, so I uninstalled them. No hubs are involved - I've always plugged straight into the tower or laptop. I've also tried two different quality (first party Motorola) cables.
Mass storage mode works fine despite the error - I can access the Internal storage as well as the SD card. Is this a problem with my phone, or am I missing some software on the Windows side?
Ben
crt_ben said:
Does anyone else have this problem? When I connect my phone to either my laptop (winXP) or my desktop (win7x64) I periodically - constantly, really - get this message:
"One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message."
When I click the message, it identifies my phone as a Generic USB Hub (4 ports) with the first child being a USB Mass Storage Device, the second being the problematic "Unknown Device" and the last two are "Unused Port"s.
This happens whether the phone is in charge-only or mass storage mode. I tried installing the autoplay drivers and that didn't help, so I uninstalled them. No hubs are involved - I've always plugged straight into the tower or laptop. I've also tried two different quality (first party Motorola) cables.
Mass storage mode works fine despite the error - I can access the Internal storage as well as the SD card. Is this a problem with my phone, or am I missing some software on the Windows side?
Ben
Click to expand...
Click to collapse
Have you tried installing the WHQL drivers for this device from here: http://www.lgforum.com/resources ?
majorpay said:
Have you tried installing the WHQL drivers for this device from here: http://www.lgforum.com/resources ?
Click to expand...
Click to collapse
Thanks for the suggestion major. I tried those drivers with no luck - the message still pops up frequently in both charge and mass storage modes.
crt_ben said:
Thanks for the suggestion major. I tried those drivers with no luck - the message still pops up frequently in both charge and mass storage modes.
Click to expand...
Click to collapse
Odd... I had issues with the original drivers, but once installed, I never had another prompt again.
edit: I had it one more time, but it found them and installed them
that's very interesting. i also use 2 machines--one with xp and one with win7. my usb connection worked flawlessly on both. fyi...my connection default is mass storage, and i've actually never tried the other options. i wonder why the difference? did you make any changes? are you rooted? i am not.
gr33nT said:
that's very interesting. i also use 2 machines--one with xp and one with win7. my usb connection worked flawlessly on both. fyi...my connection default is mass storage, and i've actually never tried the other options. i wonder why the difference? did you make any changes? are you rooted? i am not.
Click to expand...
Click to collapse
Hi gr33nT,
Thanks for responding. I'm 100% stock at the moment, not rooted or anything (though it will be soon ) Sometimes I use charge only if I have it connected to my laptop at work but I still want to listen to music from the SD card. I may see if I can get Verizon to swap out the phone, the message pops up all the time and it's getting annoying...
A quick follow-up on this one: I tried the stock LG cable on my win7 machine (I had been using moto cables). I installed BOTH the bootstrap drivers as well as the LG drivers from the web - still happening. I rooted with these drivers via S1C so I know the drivers are good. If nobody else has run into this, something is probably wonky with my phone, so I'm probably going to exchange it.
For mine, every time I connect, it asks me if I want to install bootstrap. Even though, they have already been installed cuz I am rooted.
I've had the same issue both as stock, and rooted and in every configuration with the phone and PC you can think of. I've downloaded the drivers and installed them from both the phone and web site all to no avail. This is really getting annoying.
I hope someone has a fix for this.
AndroidCraig said:
I've had the same issue both as stock, and rooted and in every configuration with the phone and PC you can think of. I've downloaded the drivers and installed them from both the phone and web site all to no avail. This is really getting annoying.
I hope someone has a fix for this.
Click to expand...
Click to collapse
Hmm...that is troubling. I'm still having the issue running the stock rom and rooted, now. When I get time I'm going to drop by the Verizon store and hopefully they'll replace the phone - I suggest you try the same, as I doubt it's the computers we're using. My win7 box and winXP work laptop could hardly be more different!
I doubt a replacement will fix anything, I experience the same thing as majorpay. Drivers worked for a while and then it started asking for it again. This also causes issues when using usb tether as its connecting and disconnecting. The issue is not present when used as a mass storage device.
bwhxeon said:
I doubt a replacement will fix anything, I experience the same thing as majorpay. Drivers worked for a while and then it started asking for it again. This also causes issues when using usb tether as its connecting and disconnecting. The issue is not present when used as a mass storage device.
Click to expand...
Click to collapse
Hi bwhxeon,
The issue (USB device not recognized - it sounds like you're referring to the autoplay driver installation) happens for me in mass storage mode also. I believe it has to be the phone as I've never had this problem on any of my PCs with my OG Droid or any other USB device. With this phone, I have the problem on all of my PCs.
I had the same problem. The error popups seemed random at first. I noticed if I enabled/disabled the WIFI on the device while it was connected, I could make the error popup.
I ended up getting a new replacement device when I also noticed the 4G Hotspot wasn't working either even after a factory restore. There was definitely a hardware issue with the phone.
USB Unknown Device
same issue here.. when using ADB though I have to set to Internet Connection then it goes away for a while until I want mass storage or just charge from USB again, then re-appears.
LG is not like most other phones as in usb debugging only works in internet connection mode where others go into it as soon as you plug it in.
Just kind of scanned this thread but have you tried a different USB cable? I was having a problem with mine only wanting to charge with the stock so I grabbed another cable and it has worked right ever since
Same issue, two different pcs, with two different cables. Bootstrap does not load anymore so I am using the drivers from the links, both sets of Lg verizon drivers
Sent from my VS910 4G using XDA App
Hello forum !
i have used a couple of hours now trying to find a solution to my problem both here on the site but also on the internets.
i just recently became the happy owner of a Note, but i have been completely unable to connect it to any of my pc's ive had a galaxy i9000 that i didnt have any problems with but with my note it wont work.
under win7 64bit - when i plug the usb cable a "boc opens" in the drop down menu called MTP and when i klick that nothing happens, ive trid the varies ways of removing the sd card unmounting it etc. and debugging and so on but wont work.
it randomly connected once but then it dissapeared from my computer.
under winXP 32bit it just says usb device not recognised, i really wanna root this thing so i can play with the true power of this amazing device.
and on both pc's ive tried with kies and driver packs both together and seperately.
anyone out there that can help me out with this problem ?
cheers
and happy new year
Prosasan
Before connecting it to the PC with the cable, click "connect storage to pc" in the USB settings. After clicking it, then it will ask you to connect to pc. If you connect to pc before clicking it will not connect.
Sent from my GT-N7000 using Tapatalk
Hello i have done that but the same happens ive done it like it says i should i just dont get why my pc wont recognise it , when i press it and then it waits for me to plug it in, i do that the dialogue box shuts and then nothing happens besides windows saying unrecognised device connected
Strange, Mine connect fine just like how marinervijay mentioned. Go to Settings > Wireless> Usb Utilities and press connect first and then insert your USB, then press connect USB. Voila. There should be a window prompting to open in your windows just like when u insert a flashdrive to ur computer.
iknow its supposed to work like that.
the problem is that it doesnt work :/
Okay, have u tried resetting your Note to factory default?
no i havent tried that, because its all new it didnt work since i got it, i never thought that that might help, ill give it a go.
thx
On another, you might have a defective USB given to you by ur retailer. Perhaps you can contact them somehow and ask them to replace your USB?
do you mean the USB cable delivered with the phone ?
Cheers
Yes. Could be a defect. I'd suggest you check with your retailer if it is replaceable if none of what mentioned is working for you.
Hi,
Have you ticked USB debugging? Its under Settings>Apps>Development
Then it should show usb connection in notification tab, tap it and set usb storage as on.
There may be few problems here so I will suggest different solutions, one might work for you
1. Turn off your antivirus and connect, it should work, see after connecting mobile that does it install something near "Bottom clock"?, open "my computer" see if it gives you N7000 (give it a minute). sometimes your computer settings are a problem
2. If no, Install latest Kies on your computer as it downloads Samsung drivers for your phone
3. after connecting 1st time, computer takes some time to recognize your mobile--be patient--
4. if all of above doesnot work, restart computer, connect USB to another (or same) port (turn off antivirus) and see
5. Nothing, try in Setting>Applications>Development>debugging Mode
6. if not, try on another computer
7. still does not connect, change USB cable
8. Still nothing there might be a issue with your device, but I will not conceive that every quickly, trying all above few times should resolve the issue..
7.
Prosasan said:
Hello forum !
i have used a couple of hours now trying to find a solution to my problem both here on the site but also on the internets.
i just recently became the happy owner of a Note, but i have been completely unable to connect it to any of my pc's ive had a galaxy i9000 that i didnt have any problems with but with my note it wont work.
under win7 64bit - when i plug the usb cable a "boc opens" in the drop down menu called MTP and when i klick that nothing happens, ive trid the varies ways of removing the sd card unmounting it etc. and debugging and so on but wont work.
it randomly connected once but then it dissapeared from my computer.
under winXP 32bit it just says usb device not recognised, i really wanna root this thing so i can play with the true power of this amazing device.
and on both pc's ive tried with kies and driver packs both together and seperately.
anyone out there that can help me out with this problem ?
cheers
and happy new year
Prosasan
Click to expand...
Click to collapse
suresh.my said:
Hi,
Have you ticked USB debugging? Its under Settings>Apps>Development
Then it should show usb connection in notification tab, tap it and set usb storage as on.
Click to expand...
Click to collapse
i already tried that ive done all that i could think of
nasgilani said:
There may be few problems here so I will suggest different solutions, one might work for you
1. Turn off your antivirus and connect, it should work, see after connecting mobile that does it install something near "Bottom clock"?, open "my computer" see if it gives you N7000 (give it a minute). sometimes your computer settings are a problem
2. If no, Install latest Kies on your computer as it downloads Samsung drivers for your phone
3. after connecting 1st time, computer takes some time to recognize your mobile--be patient--
4. if all of above doesnot work, restart computer, connect USB to another (or same) port (turn off antivirus) and see
5. Nothing, try in Setting>Applications>Development>debugging Mode
6. if not, try on another computer
7. still does not connect, change USB cable
8. Still nothing there might be a issue with your device, but I will not conceive that every quickly, trying all above few times should resolve the issue..
7.
Click to expand...
Click to collapse
thanks ill try that now.
Cheers and thanks for all the answers and inputs
tried all but the usb cable..
nasgilani said:
There may be few problems here so I will suggest different solutions, one might work for you
1. Turn off your antivirus and connect, it should work, see after connecting mobile that does it install something near "Bottom clock"?, open "my computer" see if it gives you N7000 (give it a minute). sometimes your computer settings are a problem
2. If no, Install latest Kies on your computer as it downloads Samsung drivers for your phone
3. after connecting 1st time, computer takes some time to recognize your mobile--be patient--
4. if all of above doesnot work, restart computer, connect USB to another (or same) port (turn off antivirus) and see
5. Nothing, try in Setting>Applications>Development>debugging Mode
6. if not, try on another computer
7. still does not connect, change USB cable
8. Still nothing there might be a issue with your device, but I will not conceive that every quickly, trying all above few times should resolve the issue..
7.
Click to expand...
Click to collapse
Okey ive tried them all now, more then a few times most of these ive tried already and the antivirus isnt an issue as i dont have any on this pc. i think the problem either lays at the usb cable or the device itself. i will try and get to borrow a cable from a friend or something
Cheers for all the replies and helpfull inputs
Happy new year to everyone ^^
Have you tried connecting note to the pc using wireless?
Kies allows you to connect wirelessly.
good point!
sunnysurya said:
Have you tried connecting note to the pc using wireless?
Kies allows you to connect wirelessly.
Click to expand...
Click to collapse
i havent tried that, but does that work when u need to root it ?
cheers
I got root access
Prosasan said:
i havent tried that, but does that work when u need to root it ?
cheers
Click to expand...
Click to collapse
Hey,
I am able to get USB storage, and I got root access thru the batch files and help provided in this link: http://forum.xda-developers.com/showthread.php?t=1329360
I have Kies installed and this probably helped detect the phone.
Hope this helps..
USb Problem
Hi I've had the same problem.
I have been using the Note quite happily as a Mass USB storage since early December. Plugged it in this morning and I don't get anything. I have also tried the debugging and all the other things listed. Here's what I get:
Usb debugging on - just a sound and a charging indication
Usb debugging off -usb connected Mtp connected on the notification pull down page. When I click on notification it just shuts the window.
I have tried dialling *#7284# and selecting USB PDA which didin't do anything for me but others seem to have had some luck. See this link:
blog.vacs.fr/index.php?post/2010/12/24/How-to-repair-the-USB-not-detected-problem-on-Android-Samsung-phones
I will be rebooting tonight but I don't really want to.
only the Samsung USB wire works
I had this problem today. The Note would never connect the USB or external storage. I searched and found this thread.
I then noticed it was another USB cable (I gave about 1,000 now!). I tried the Samsung one, and it worked first time.
It is annoying, because these cables are normally swappable with any device. It appears Samsung have defined their own standard. The great thing about standards, of course, is that there are some many to choose from!
USB cable was defect - and replaced
Thanks for the help everyone